OPERATION AND PARTS MANUAL
MODEL MQ-D306HA
DIAPHRAGM PUMP
(Honda Gasoline Engine)
Revision #3 (01/09/07)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA —TABLE OF CONTENTS
MQ-D306HA Gasoline
Powered Diaphragm
HONDAGX120K1QX2 Engine
Air Cleaner Assembly......................................... 36-37
Camshaft Assembly ........................................... 38-39
Carburetor Assembly ......................................... 40-41
Control Assembly ............................................... 42-43
Crankcase Cover Assembly............................... 44-45
Crankshaft Assembly ......................................... 46-47
Cylinder Barrel Assembly................................... 48-49
Cylinder Head Assembly.................................... 50-51
Fan Cover Assembly .......................................... 52-53
Flywheel Assembly ............................................ 54-55
Fuel Tank Assembly ........................................... 56-57
Ignition Coil Assembly ........................................ 58-59
Muffler Assembly ............................................... 60-61
Piston Assembly................................................. 62-63
Recoil Starter Assembly..................................... 64-65
Gasket Kit Assembly .......................................... 66-67
Pump
Proposition 65 Warning ............................................. 2
Table of Contents ...................................................... 3
Parts Ordering Procedures .................................... 4-5
Specifications (Pump/Engine) ....................................6
Pump Dimensions ......................................................7
Safety Message Alert Symbols .............................. 8-9
Rules For Safe Operation .................................. 10-11
General Information .................................................12
Pump Components ..................................................13
Basic Engine ............................................................14
Pre-Inspection (Engine) ...........................................15
Pre-Set-up (Pump)............................................. 16-17
Initial Start-up (Engine) ...................................... 18-19
Maintenance (Pump) ......................................... 20-21
Maintenance (Engine)........................................ 22-23
Preparation for Long-Term Storage.........................24
Troubleshooting (Pump)...........................................25
Troubleshooting (Pump/Engine) ..............................26
Explanation Of Code In Remarks Column ...............28
Suggested Spare Parts ............................................29
Terms and Condition Of Sale
—
Parts .................... 68
As a continuing effort to
update our parts book,
contact the MULTIQUIP
literature department for the
latest revision of your
"Operation and Parts
Manual"
ComponentDrawings
Water Box and Groove Assembly ...................... 30-31
Pump Assembly ................................................. 32-35
Specification and part number
are subject to change without
notice.
PAGE 4 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective:June 1st, 2005
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
■ Next Day
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
Unless otherwise indicated by customer, all orders are treated asStandard Orders and will ship
within24hours.WewillmakeeveryefforttoshipAirShipmentsthesamedaytheorderisreceived,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA— SPECIFICATIONS (PUMP/ENGINE)
Table 1. Specifications (Pump)
MQ-306H Diaphragm
Type
Pump
Suction & Discharge
3.00 in. (76 mm.)
Size
Maximum Pumping
Capacity
5,100 gallons/hour
(19,305 liters/hour)
Pump
Max. Soilds Diameter
Max Lift
1.5 in. (38 mm)
25 ft. (7.62 meters)
50 ft. (15.24 meters)
160 lbs. (72 Kg.)
Max. Head
Dry Net Weight
Table 2. Specifications (Engine)
Model
HONDA GX120K1QX2
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Type
2.4 in. x 1.7 in.
(60 mm x 42 mm)
Bore X Stroke
Displacement
Max Output
119 cc (7.2 cu-in)
4.0 H.P./3600 R.P.M.
0.66 US gal. (2.5 liters)
Engine
Fuel Tank Capacity
Unleaded Automobile
Gasoline
Fuel
Lube Oil Capacity
0.63 qts. (60 liters)
Centrifugal Fly-weight Type
Recoil Start
Speed Control
Method
Starting Method
11.7 x 13.4 x 12.5 in.
(297 x 341 x 318 mm)
Dimension
(L x W x H)
Dry
Net Weight
28.7 lbs (13 Kg.)
PAGE 6 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA— DIMENSIONS (PUMP)
Figure 1. MQ-D306HA Pump Dimensions
Table 3. Dimensions
A
B
C
MODEL
LENGTH
WIDTH
HEIGHT
36.0 in.
(91 cm.)
19.0 in.
(48 cm.)
27.0 in.
(69 cm.)
MQ-306HA
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA— SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Potential hazards associated with the operation of the MQ
Model D-306H, B and R Diaphragm Pumps. will be referenced
with Hazard Symbols which appear throughout this manual,
and will be referenced in conjunction with Safety Message
Alert Symbols.
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
WARNING - Lethal Exhaust Gas Hazards
operation of the MQ Model
D306HA Diaphragm Pump. Refer
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide ample free flow
air.
to the engine manufacturers
instructionsfordatarelativetoitssafe
operation.
Before using these pumps, ensure that the operating
individual has read and understands all instructions in this
manual.
SAFETY MESSAGE ALERT SYMBOLS
DANGER - Explosive Fuel Hazards
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER, WARNING, or CAUTION.
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
WARNING - Burn Hazards
WARNING
You CAN be KILLED or SERIOUSLY injured if you DO
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
NOT follow directions.
CCAUTION
You CAN be INJURED if you DO NOT follow directions.
WARNING - Respiratory Hazards
ALWAYS wear approved respiratory
protection when required.
PAGE 8 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA— SAFETY MESSAGE ALERT SYMBOLS
CAUTION - Equipment Damage Hazards
CAUTION - Rotating Parts Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your light tower, other
property, or the surrounding environment.
CAUTION - Accidental Starting Hazards
CAUTION - Read Manual
ALWAYS place the power source, circuit
breakers or ON/OFF switch in the OFF
position, when the generator is not in use,
unless connected to transfer switch.
Before attempting to operate
the pump, and to avoid serious
injury to personnel, always
read and understand operation
manual. Failure to read and
understand operation manual
could result in serious harm
or even death!
CAUTION - Eye and Hearing Hazards
ALWAYS wear approved eye and
hearing protection.
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or mixer.
Read this manual!
DANGER
Failure to follow instructions in this manual may lead to
serious injury or even death! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
■
High Temperatures – Allow the
engine to cool before adding fuel or
performing service and maintenance
functions. Contact with hot! components can cause
serious burns.
The following safety guidelines should always be used when
operating the MQ Model D-306H Diaphragm Pump.
■
The engine section of this mixer requires an adequate
free flow of cooling air. NEVER operate the mixer in any
enclosed or narrow area where free flow of the air is
restricted. If the air flow is
GENERAL SAFETY
■
DO NOT operate or service this
equipment before reading this entire
manual.
restricted it will cause
serious damage to the
mixer or engine and may
cause injury to people.
Remember the pump's
engine gives off DEADLY
carbon monoxide gas.
■
■
This equipment should not be operated
by persons under 18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, llness or taking
medicine.
ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool.DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
NEVER operate this equipment under the
influence of drugs or alcohol.
■
■
NEVER operate the pump in an
explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■
ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the mixer.
Topping-off to filler port is dangerous, as it tends to spill
fuel.
■
■
■
■
NEVER place hands inside the drum while the blades are
rotating.
■
■
Maintain this equipment in a safe operating condition at
all times.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacture does not assume responsibility for any
accident due to equipment modifications.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
PAGE 10 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — RULES FOR SAFE OPERATION
■
■
■
ALWAYS be sure the operator is familiar with proper safety
TRANSPORTING
precautions and operation techniques before using pump.
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
NEVER leave the pump unattended, turn off engine when
unattended.
NEVER pump volatile, explosive, flammable or low flash point
fluids.These fluids could ignite or explode.
■
Drain fuel when transporting pump over long distances
or bad roads.
■
■
NEVER operate the pump in an explosive atmosphere.
MAINTENANCE
Keep all inexperienced and unauthorized people away
from the equipment at all times.
■
NEVER lubricate components or attempt service on a
running pump.
■
Before starting the pump, check that the clean-out cover is
securely fasten.
■
ALWAYS allow the pump a proper amount of time to
cool before servicing.
■
■
ALWAYS ensure pump is on level ground before use.
■
■
Keep the pump in proper running condition.
Fix damage to the pump immediately and always replace
broken parts.
Become familiar with the components of the pump before
operating.
■
■
ALWAYS replace any worn or damaged warning decals.
■
■
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste.
NEVER pump corrosive chemicals or water containing toxic
substances. These fluids could create serious health and
environmental hazards. Contact local authorities for
assistance.
■
NEVER open the priming plug when pump is hot. Hot water
inside could be pressurized much like the radiator of an
automobile. Allow pump to cool to the touch before loosening
plug.
EMERGENCIES
■
ALWAYS know the location of the nearest fire
extinguisher and first aid kit.
■
■
NEVER open the pump housing during operation or start the
pump with the clean-out cover removed.The rotating impeller
inside the pump can cut or sever objects caught in it.
NEVER block or restrict flow from discharge hose. Remove
kinks from discharge line before starting pump. Operation
with a blocked discharge line can cause water inside pump
to overheat.
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■
ALWAYS fill the pump casing with water before starting the
engine. Failure to maintain water inside the pump housing
will cause severe damage to the pump.
■
■
In winter drain water from pump housing to prevent freezing.
ALWAYS test the engine ON/OFF switch before operating.
The purpose of this switch is to shut down the engine .
■
Refer to the HONDA Engine Owner's Manual for engine
technical questions or information recommended by
Multiquip for this equipment. Damage to the equipment
and/or injury to user may result.
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — GENERAL INFORMATION
Elevation
APPLICATION
Higher elevations will effect the performance of the pump. Due to
less atmospheric pressure at higher altitudes, pumps DO NOT
have the priming ability that they have at sea level. This is due to
the “thinner air” or lack of oxygen at higher altitudes.
The MQ Model D305HA diaphragm pump is designed to be
used for de-watering applications. The suction and discharge
ports on this pump use a 3-inch diameter opening, which allows
the pump to pump at rate of approximately 5,100 gallons/hour
(gph) or 19,305 liters/hour (lph).
A general rule of thumb is that for every 1,000 feet of elevation
above sea level a pump will lose one foot of priming ability.
Diaphragm pumps use a positive displacement design rather
than centrifugal force to move water through the casing. This
means the pump will deliver a specific amount of flow per stroke,
revolution or cycle. These pumps are commonly referred to as
mud hogs, mud hens and mud suckers.Their names reflect their
popularity for use in applications where shallow depths and slurry
water render centrifugal pumps ineffective
For example, in Flagstaff, Arizona where the elevation is
approximately 7,000 feet, the pump would have a suction lift of
only 18 feet rather than the 25 feet at sea level. Table 3 shows
suction lift at various elevations.
Table 3. Suction Lift at Various Elevations
Altitude
Power Plant
Suction Lift in Feet (Meters)
Feet (Meters)
This diaphragm pump is powered by a 5.5 horsepower air cooled,
4-stroke, single cylinder, HONDA GX-120 gasoline engine that
incorporates a low "Oil Alert Feature" . The drive shaft of the
engine is coupled to an offset connecting rod that is coupled to a
flexible diaphragm. The connecting rod alternately raises
(expands) and lowers (contracts) the diaphragm at a rate
between 40 and 65 strokes per minute depending on engine
speed.
Sea Level
10.0 (3.048) 15.0 (4.572) 20.0 (6.096) 25.0 (7.620)
8.80 (2.680) 13.2 (4.023) 17.6 (5.364) 22.0 (6.705)
7.80 (2.377) 11.7 (3.566) 15.6 (4.754) 19.5 (5.943)
6.90 (2.103) 10.4 (3.169) 13.8 (4.206) 17.3 (5.273)
6.20 (1.889) 9.30 (2.834) 12.4 (3.779) 15.5 (4.724)
2,000 (610)
4,000 (1,219)
6,000 (1,829)
8,000 (2,438)
10,000 (3,048) 5.70 (1.737) 8.60 (2.621) 11.4 (3.474) 14.3 (4.358)
Oil Alert Feature
Table 4 shows percentage drops in performance as elevation
In the event of low oil or no oil, the HONDA GX-120 engine has increases.
a built-in oil alarm engine shut-down feature. In the event the oil
level is low the engine will automatically shut-down.
Table 4. Performance Loss at Various
Elevations
Suction Lift
This pump is intended to be used for dewatering applications
and is capable of suction lifts up to 25 feet at sea level. For optimal
suction lift performance keep the suction hose or line as short as
possible. In general always place the pump as close to the water
as possible.
Altitude
Feet (Meters
Discharge Flow
Discharge Head
Sea Level
100%
97%
95%
93%
91%
88%
100%
95%
91%
87%
83%
78%
2,000 (610)
Pump Support
4,000 (1,219)
6,000 (1,829)
8,000 (2,438)
10,000 (3,048)
The pump should always be placed on solid stationary ground
in a level position.
NEVER place the pump on soft soil. The suction hose or pipe
connection should always be checked for tightness and leaks. A
small suction leak in the hose or fittings could prevent the pump
from priming.
Please contact your nearest authorized MQ
dealer for any accessories that your pump
may require.
NOTE
PAGE 12 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — PUMP COMPONENTS
Figure 2 shows a typical application using the MQ D306HA series diaphragm pump. Please note that this pump is intended for the
removal of clean water and water containing some debris and solids. Maximum size of solids should not exceed 1.5 inch (38 mm)
in diameter. DO NOT set strainer on bottom of water bed. Placing the strainer above the water bed will prevent the pump from
drawing in excessive amounts of sand and foreign debris.
Contact your nearest
Multiquip dealer for
quick disconnect hoses
and fittings.
Figure 2. MQ-D306HA Pump Application
4. Worm Clamp – Used to secure the hose to the inlet and
outlet ports on the pump. Use two clamps to secure the
hose on the inlet side of the pump.
5. Discharge Hose – Connect a flexible rubber hose to the
discharge port on the pump. Make sure that the hose lays
flat and is not kinked. Use only recommended type discharge
hose. Contact Multiquip parts department for ordering
information.
1. Pump – The MQ D306HA is a 3-inch diaphragm pump
that is used in general de-watering applications. Typical
dewatering applications consist of cleaning out cesspools
6. Suction Port – Connect a 3-inch inlet hose to this port.
and septic tanks, draining slow seepage from small
excavations, trenches and construction sites, or pumping
out industrial waste.
Use two worm clamps to secure the hose.
7. Suction Hose – Connect a flexible rubber hose to the
suction port on the pump. Make sure that the hose lays flat
and is not kinked. Use only recommended type suction hose.
Contact Multiquip parts department for ordering information
2. Fill Cap – Prior to operation, the pump casing should be
filled with water.Remove this cap to add water to the pump.
After the initial prime, a sufficient amount of water will be
retained in the casing so that the operator will not need to
re-prime later.
8. Strainer – Always attach a strainer to bottom side of the
suction hose to prevent large objects and debris from
entering the pump. Strainer should be positioned so that it
will remain completely under water.Running the pump with
the strainer above water for long periods can damage pump.
If the casing is dry or has insufficient water, the pump will
have difficulty in priming which could lead to premature
mechanical seal wear thus causing damage to the pump.
9. Support Body – This unit is equipped with a hinged
support assembly, that allows for easy access to the pump
body.
3. Discharge Port – Connect a 3-inch discharge hose to
this port. Use two worm clamps to secure the hose.
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — BASIC ENGINE
Figure 3. Engine Controls and
Components
INITIAL SERVICING
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
The engine (Figure 3) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the Honda manufacturers
engine manual for instructions and details for operation and
servicing.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
Explosive Fuel
DANGER - Explosive Fuel
allow dirt to enter the engine,
causing rapid engine wear.
Adding fuel to the tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until
the fuel residue has been completely wiped up,
and the area surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
9. Muffler – Used to reduce noise and emissions.
CAUTION - Burn Hazard
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediately after operating. NEVER operate
the engine with the muffler removed.
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
PAGE 14 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — PRE-INSPECTION (ENGINE)
CAUTION - Read Manual
Please read the entire maintenance section
in this manual before servicing the pump. In
addition for operator safety, please read all
safey messages at the begining of the
manual
Figure 5. Engine Oil Dipstick (Oil Level)
Inspection
1.
2.
3.
4.
Clean the pump, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
Table 5. Oil Type
Temperature
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
Season
Summer
Spring/Fall
Winter
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
25°C or Higher
25°C~10°C
Check carburetor for external dirt and dust. Clean with dry
compressed air.
Check fastening nuts and bolts for tightness.
0°C or Lower
Engine Oil Check
1.
To check the engine oil level, place the pump on secure
level ground with the engine stopped.
DANGER - Explosive Fuel
Motor fuels are highly flammable and can be
dangerous if mishandled. DO NOT smoke
while refueling. Adding fuel to the tank
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 4) and wipe clean.
should be done only when the engine is
stopped and has had an opportunity to cool
down. DO NOT attempt to refuel the pump if the engine is
hot! or running In the event of any spilled fuel, wipe up
immediately. DO NOT attempt to start the engine until the
fuel residue has been completely wiped up, and the area
surrounding the engine is dry.
Fuel Check
Figure 4. Engine Oil Dipstick (Removal)
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
3. When refueling, be sure to use a strainer for filtration. DO
4. If the oil level is low (Figure 5), fill to the edge of the oil filler
hole with the recommended oil type (Table 5).Maximum oil
capacity is .63 quarts (.60 liters)
NOT top-off fuel. Wipe up any spilled fuel immediately!
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — PRE-SETUP (PUMP)
3. Remember suction hoses must be rigid enough not to
Before Starting:
CAUTION - General Safety Precautions
collapse when the pump is in operation.
4. Check that the discharge hose (Figure 2) is not restricted.
Place hose so that it lays as straight as it is possible on the
ground. Remove any twists or sharp bends from hose which
may block the flow of water.
NEVER operate the pump in a confined
area or enclosed area structure that does
not provide ample free flow of air.
ALWAYS wear approved eye and hearing
protection before operating the
compactor.
Suction and discharge hoses are
NOTE
available from Multiquip. Contact
your nearest dealer for more
information.
Before Starting
5. The discharge hose is usually a collapsible (thin-walled)
hose, however if a thin-walled discharge hose is not avail-
able, a rigid suction hose can be substituted in its place.
1. Read safety instructions at the
beginning of manual.
2. Place pump as near to water as
possible,onafirmflat,levelsurface.
6. Make sure the suction strainer (Figure 2) is clean and
securely attached to the water end of the suction hose. The
strainer is designed to protect the pump by preventing large
objects from being pulled into the pump.
3. Toprimepump,removefillcap(Figure2)andfillpumpcasing
with water.If the pump casing is not filled with water before
starting, it will not begin pumping.
CAUTION - Strainer
The strainer should be positioned so it will remain completely
under water. Running the pump with the strainer above
water for long periods can damage the pump.
CAUTION - Pump Casing
Pump casing must be filled with water before using
pump. Otherwise pump will not be able to begin
pumping.
CAUTION - Flammable Fluids
DO NOT pump flammable fluids, corrosive chemicals or fluids
containing toxic substances. These fluids can create potentially
dangerous health and environmental hazards. Contact local
authorities for assistance.
WARNING - Fill Cap
DO NOT open fill cap if pump is hot! Water inside may
be under pressure.
4. Checkforleaksbetweenpumpandengine.Ifwaterisleaking
between the pump and engine housing, the seal inside the
pumpmaybewornordamaged.Continued operationofthe
pumpisnot recommended.Furtherusageofthe pumpunder
theseconditionsmaycauseseverewaterdamagetoengine.
CAUTION - Mechanical Seal
This pump uses a water-cooled mechanical seal to prevent
water from seeping into the engine. The passage of water
through the pump casing lubricates the seal and prevents it
from overheating. NEVER! operate the pump without water
in the casing as this will cause damage to the mechanical
seal.
Hoses and Clamps
1. Check that all hoses are securely attached to the pump.
Make certain suction hose (Figure 2) does not have any air
leakage.Tighten hose clamps and couplings as required.
2. Itisrecommendedthat 2 clampsbeusedwhensecuringthe
suction hose to the inlet side (suction) of the pump.
PAGE 16 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — PRE-SETUP (PUMP)
Connecting Rod Bearing Lubrication
Gear Reduction Oil (Transmission)
1. Grease connecting rod bearing thru the access
1.
Remove the transmission oil level plug (Figure 6). If oil
begins to seep out as the plug is being removed, then it
can be assumed that the transmission oil is at the proper
operating level.
hole (Figure 7) every 25 hours of operation.
2.
Use only premium lithium based grease, conforming to
NLG1 Grade #2 consistency.
2.
If oil does not seep out as the oil level plug is being removed,
then remove the transmission oil fill plug and fill with
SAE 80/90 EP gear oil to the proper operating level.
Transmission oil capacity is capacity is 1-1/4 pints (590 ml.).
Figure 7. Connecting Rod Bearing Lubrication
Figure 6.Transmission Oil Level
Diaphragm pumps will handle fluids
containing considerable solids (not to
exceed 1.5 inch/28 mm), however, if
the mixture is too heavy to be pumped,
water must be added until the mixture
becomes sufficiently fluid for pumping.
NOTE
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA— INITIAL START-UP (ENGINE)
4. Placethechokelever(Figure 9)inthe"CLOSED"position
CAUTION - Read Manual
if starting a warm engine or the temperature is warm.
DO NOT attempt to operate the pump until the
Safety, General Information and Inspection
sections of this manual have been read and
thoroughly understood.
This section is intended to assist the operator with the initial
start-up of the diaphragm pump. It is extremely important that
this section be read carefully before attempting to use the pump
in the field.
Starting the Engine (HONDA engine)
1. Place the engine fuel valve lever (Figure 8) to the "ON"
position.
Figure 11. Engine Choke Lever (Closed)
5. Place the engine ON/OFF switch (Figure 12) in the "ON "
position.
Figure 8. Engine FuelValve Lever (ON Position)
2. Move the throttle lever (Figure 9) away from the slow
position, about 1/3 of the way toward the fast position.
Figure 12. Engine ON/OFF Switch (ON Position)
6. Grasp the starter grip (Figure 13) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
Figure 9. Throttle Lever (1/3 Start Position)
3. Place thechokelever(Figure10)inthe"OPEN"positionif
starting a cold engine.
Figure 13. Starter Grip
Figure 10. Engine Choke Lever (Open)
PAGE 18 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA— INITIAL START-UP (ENGINE)
7. If the engine has started, slowly return the choke lever Stopping The Engine
(Figure14)tothe“CLOSED”position.Iftheenginehasnot
started repeat steps 1 through 6.
Normal Shutdown
1. Movethethrottlelever tothe IDLEposition (Figure16)and
run the engine for three minutes at low speed.
Figure 16.Throttle Lever (Idle)
2. Aftertheenginecools,turntheengineON/OFFswitchtothe
“OFF” position (Figure 17).
Figure 14. Choke Lever (Closed)
8. Beforethepumpisplacedintooperation,runtheenginefor
severalminutes. Checkfor fuelleaks,andnoisesthatwould
associate with a lose component.
9. To begin pumping, place the throttle lever (Figure 15) in the
"RUN" position.
Figure 17. Engine ON/OFF Switch (OFF)
3. Place the fuel shut-off lever (Figure 18) in the ”OFF”
position.
Figure 15.Throttle Lever (Run)
Figure 18. FuelValve Lever (OFF)
Emergency Showdown
1. Move the throttle lever quickly to the “IDLE” position, and
Pump speed can be regulated with
the engine throttle control from full
place the engine ON/OFF switch in the “OFF” position.
volume, 65 strokes per minute, to
about 40 strokes per minute for
lesser volume. Smoothest operation
can be determined by trying to pump at several speeds. Limit
maximum speed to 65 strokes per minute of the diaphragm (2,800
RPM engine speed).
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — MAINTENANCE (PUMP)
Pump Vacuum Test
CAUTION - Priming Pump
Pump Cleaning
After pumping water containing large amounts of dirt and
debris, perform the following:
DO NOT attempt to start the engine unless the pump has
previously been primed with water. Severe pump damage
will occur if pump has not been primed.
1. Remove the drain plug from the pump housing (Figure 2)
and drain any water left in the pump.
3. Clean and remove dirt, debris from pump casing.Inspect
impeller and volute for wear. Replace any damaged or
worn parts.
To perform the pump vacuum test do the following:
Gear Reduction Oil (Transmission)
1. Remove the pump fill cap (Figure 2), and fill the pump
with water.
1.
Change transmission oil after the first 40 hours of
operation. Use SAE 80/90 EP gear oil. Transmission oil
capacity is 1-1/4 pints (590 ml.). Check oil level periodically
and change oil after every 400 hours of operation.
2. Start the engine as outlined in the initial start-up section,
and wait for the pump to begin pumping.
3. As shown in Figure 19 (next page), place a water hose
inside the discharge opening of the pump, and turn on
the water.This flow of water into the discharge opening
will prevent the pump from running dry.
Connecting Rod Bearing Lubrication
1. Grease connecting rod bearing thru the access
hole (Figure 7) every 25 hours of operation.
2.
Use only premium lithium based grease, conforming to
NLG1 Grade #2 consistency.
4. Place the Pump Vacuum Tester (P/N 7000030) over
the pump suction (inlet) opening (Figure 19) with the
vacuum gauge facing upwards. It may be necessary to
apply a small amount of water around the rubber seal of
the vacuum tester to make a good suction fit.
Connecting Rod Bearing Lubrication
1. Keep interior of pump and valves clean. Flush out
pump with clear water after operation.
2. Remove connecting rod guard occasionally and wipe
up excess grease from connecting rod bearing.
5. Check and make sure that there are no air leaks between
the vacuum tester and the inlet port on the pump. If air
leaks are present reseat vacuum tester.
6. Run the pump for a few minutes while monitoring the
vacuum gauge. If the gauge indicates a reading between
-25 and -20 in. Hg. (inches of mercury) then it can be
assumed that the pump is working correctly.
25 in. Hg (inches of mercury)
translates into 25 feet of lift at sea
level.
7. If the vacuum tester gauge indicates a reading
below -20 in. Hg, it can then be assumed that the pump
is not functioning correctly, and corrective action needs
to be taken.
6. To test the flapper valve, shut down the engine. The
vacuum tester should remain attached to the pump
suction inlet port by vacuum. This indicates the pump's
flapper valve is seating properly to hold water in the
suction hose when the engine is stopped.This prevents
backflow and allows for faster priming when the engine
is restarted.
PAGE 20 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — MAINTENANCE (PUMP)
Figure 19. PumpVacuumTester
Pressure reading may vary depending on
altitude. See Tables 3 and 4.
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — MAINTENANCE (ENGINE)
Engine Maintenance
Perform engine maintenance procedures as referenced by
Table 6 below:
Table 6. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA shop Manual for service procedures
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
Reference manufacturer engine
manual for specific servicing
instructions.
PAGE 22 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — MAINTENANCE (ENGINE)
Maintenance
DANGER - Combustion (Fire , Explosion)
Performtheenginemaintenanceproceduresasindicatedbelow:
DO NOT usegasoline as a cleaning solvent.The possibility
exists of fire or explosion..
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
spring box and bellows for oil leaks. Repair or replace as
needed.
ENGINEAIRCLEANER
1. Remove the air cleaner cover and foam filter element as
shown in Figure 22.
WEEKLY
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
2. Tap the paper filter element (Figure 22) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
elementfromtheaircleanercaseside.NEVER brushoffdirt.
Brushingwillforcedirtintothefibers.Replacethepaperfilter
element if it is excessively dirty.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 20), then adjust
the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
3. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
Figure 20. Spark Plug Gap
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 21.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 5. Engine oil capacity is 1.16 quarts (1.1 liters).
DO NOT overfill.
4. Install drain bolt with sealing washer and tighten se-
curely.
Figure 22. Engine Air Cleaner
Figure 21. Engine Oil (Draining)
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — PREPARATION FOR LONG -TERM STORAGE
Pump Storage
For storage of the pump for over 30 days, the following is
required:
z
z
z
Drain the fuel tank completely.
Run the engine until the fuel is completely consumed.
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
z
Remove the pump cover and clean inside of pump
housing. Coat inside of pump housing with a light film of
oil to reduce corrosion. A spray can of oil works well for
this application.
z
z
z
Cover suction and discharge ports with duct tape to
prevent any foreign matter from falling into pump.
Cover pump and engine with plastic covering or
equivalent and store in a clean, dry place.
To protect the water cooled-seals, place one-half pint of
lubricating oil (new or used) through the discharge opening
on the pump and crank the engine several times. This
will prevent excessive corrosion and also keep the
mechanical seal lubricated.
PAGE 24 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to start
POSSIBLE PROBLEM
SOLUTION
Ignition plug being bridge?
Carbon deposit at ignition?
Check ignition system.
Clean or replace ignition.
Replace insulators.
Fuel is available but spark plug
will not ignite. (Power available
at high tension cable).
Short circuit due to defective
insulators?
Improper spark gap?
Set spark plug gap to the correct gap.
Check stop switch circuit. Replace stop switch if defective.
Replace ignition coil.
Short circuit at stop switch?
Ignition coil defective?
Fuel is available but spark plug
will not ignite. (Power NOT
available at high tension cable).
Muffler clogged with carbon
deposits?
Clean or replace muffler.
Mixed fuel quality is
inadequate?
Check fuel to oil mixture.
Fuel is available and spark plug
ignites (compression normal).
Fuel in use inadequate (water,
dust)?
Flush fuel sytem and replace with fresh fuel.
Air Cleaner clogged?
Defective cylinder head gasket?
Cylinder worn?
Clean or replace air cleaner.
Tighten cylinder head bolts or replace head gasket.
Replace cylinder.
Fuel is available and spark plug
ignites (compression low ).
Spark plug loose?
Tighen spark plug.
Operation not satisfactory
Air cleaner clogged?
Air in fuel line?
Clean or replace air cleaner.
Bleed (remove air) from fuel line.
Not enough power available
(compression normal, no miss-
firing).
Fuel level in carbureator float
chamber improper?
Adjust carbureator float
Carbon deposits in cylinder?
Ignition coil defective?
Clean or replace cylinder
Flush fuel sytem and replace with fresh fuel.
Replace ignition wires, clean ignition.
Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss-
firing).
Ignition plug often shorts?
Fuel in use inadequate (water,
dust)?
Excessive carbon depostion in
combustion chamber?
Clean or replace crankcase.
Clean or replace muffler.
Engine overheats.
Exhaust or muffler clogged with
carbon.
Spark plug heat value incorrect? Replace spark plug with correct type spark plug.
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — TROUBLESHOOTING (ENGINE/PUMP)
TABLE 7. ENGINE TROUBLESHOOTING (Continued)
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Operation not satisfactory
Governor adjustment improper?
Governor spring defective?
Fuel flow erratic?
Adjust governor to correct lever.
Clean or replace ignition.
Check fuel line.
Rotational speed fluctuates.
Air taken in through suction
line?
Check suction line.
Dust in rotating part?
Spring spring failure?
Clean recoil starter assembly.
Replace sprial spring.
Recoil starter not working
properly.
TABLE 8. PUMP TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Not enough priming water in the housing?
Engine speed too low?
Add water.
Increase throttle.
Clean strainer.
Strainner plugged?
Suction hose damaged?
Replace or repair hose, and clamps
Check that fittings are tight and properly sealed.
Move pump closer to water.
Air leak at suction port?
Pump is located too high above water line?
Debris collecting in pump housing?
Pump does not take on water.
Clean pump housing.
Water leaking out weep hole between pump and Check condition of mechanical seal and gaskets,
engine?
between pump end and engine housing.
Check that valves are seated correctly. Pour water in
in suction chamber to help seal valves.
Valves not seated correctly?
Pump does not prime correctly?
Engine speed too low?
Check diaphragm for breaks or leaks.
Increase throttle speed.
Clean strainer.
Pump takes in water, little or no
discharge.
Suction strainer partially plugged?
Tighten, replace or add clamp. (Keep extra seals on
pump)
Fittings/clamps are not sealed properly?
Suction hose leaks at inlet.
Hose diameter is too large?
Pressure too high?
Use smaller diameter hose or replace hose.
Check pressure, add additional clamp.
Check hose.
Discharge hose does not stay
on coupling.
Hose kinked or end blocked?
PAGE 26 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
he contents of this catalog are
ubject to change without notice.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number”Column
All parts with same symbol in the number column, , #,
or <, belong to the same assembly or kit.
+, %,
*
If more than one of the same
reference number is listed, the
last one listed indicates newest
(or latest) part available.
PAGE 28 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA— SUGGESTED SPARE PARTS
MQ-D306HA DIAPHRAGM PUMP
1TO 3 UNITS WITH
HONDA GX120K1QX2 ENGINE
Qty.
P/N
Description
3 ......... 17210ZE0505 .. ELEMENT AIR CLEANER DUAL
3 ......... 9807955846 ..... SPARK PLUG
1 ......... 17620ZH7023 .. CAP, FUEL WITH GASKET
1 ......... 28462ZH8003 .. ROPE STARTER
1 ......... 3052726 ........... DIAPHRAGM
2 ......... 3054937 ........... FLAP VALVE
1 ......... 1506060 ........... PLUG, FILL PLASTIC
1 ......... 1506064 ........... O-RING
1 ......... 0742304080 ..... STRAINER
Part number on this Suggested
Spare Parts List may super cede/
replace the P/N shown in the text
pages of this book.
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — WATERBOX AND GROOVE ASSY.
WATERBOX AND GROOVE ASSY.
PAGE 30 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — WATERBOX AND GROOVE ASSY.
WATERBOX AND GROOVE ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
3053041
3054932
3065985
3054935
3054936
3054938
3054937
3054939
2021032
1506064
1506060
3054933
306EC400037
3054929
PART NAME
QTY.
2
1
8
2
2
2
2
2
4
1
1
1
8
1
3
1
1
1
1
2
1
1
4
3
REMARKS
NIPPLE, SUCTION AND DISCHARGE
SUCTION CONNECTION
STUD 3/8”-16 X 2-1/8”, H.N., L.W.
GASKET, SUCTION AND DISCHARGE
FLAP VALVE SEAT WITH SPRING PIN
VALVE WEIGHT
FLAP VALVE
VALVE BINDER
SCREW MACHINE RND HEAD 10-32x1/2
O-RING FILL PLUG
PLUG FILL PLASTIC
DISCHARGE CONNECTION
NUT, 3/8"-16
WATERBOX
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
25
26
306A0200500200ZC 1/2” -13 X2” CARRIAGE BOLT, H.N.
3052724
3052726
3055026
3054992
3051812
3054944
0742304080
3051213
DIAPHRAGM BOTTOM
DIAPHRAGM
CONNECTING ROD, CARRIAGE BOLD
DIAPRHAGM TOP
SPRING PIN (1/8" DIA.x1/2')
SPRING COMPRESSION
STRAINER
SCREW HEX 1/2"x1-3/4" 13 UNCX
NUT, HEX 1/2"-13
306EC400050
2023800
WASHER, LOCK 3/8"
8
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — PUMP ASSY.
PUMP ASSY.
PAGE 32 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — PUMP ASSY.
PUMP ASSY.
PART NO.
NO.
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
PART NAME
QTY. REMARKS
3064771
3051213
3051200
3054850
2024540
3054858
2063070
2024853
2020807
2025058
2063040
2024852
2023417
2023020
2021434
2064851
2021827
2061880
3051421
2021421
2024945
3051420
2021402
2024854
2029106
2025100
2024859
2024856
2025160
2025165
2025601
2025162
2025167
GX120K1QX2
3054953A
2024964
3051012
PUMP FRAME
1
4
4
1
1
1
1
1
2
1
2
1
1
1
2
1
2
1
9
11
1
2
2
1
1
1
1
1
4
4
1
4
8
SCREW, HEX 1/2"x1-3/4" 13 UNCX
WASHER, WASHER 1/2"
GEAR CASE
PLUG PIPE VENTED 3/8" PLASTIC
GASKET, GEAR CASE
BEARING BALL
GEAR SHAFT
KEYWOODRUFF #807
GEAR 79T
BEARING BALL
PINION 11T
GEAR INTERNAL 85T
BEARING BALL
PIN DOWEL 1/4 DIA.x3/4"
COVER, GEAR CASE
PIPE PLUG 1/8" NPT SQ.HD.
NEEDLE BEARING
SCREW, HEX 1/4"-20x1
WASHER, LOCK 1/4"
LIFTING HOOK
SCREW, HEX HEAD PLATED
WASHER, FLAT 1/4"
PINION 14T 3/4 BORE
BEARING BALL
RING RETAINING EXTERNAL
“O” RING
ENGINER ADAPTER
SCREW 8W HDCP 5/16" 18UNCx1"
WASHER,TOOTH LOCK
KEY 3/16" SQ.x1"
SCREW HEX 5/16" 24UNFx1"
WASHER, LOCK 5/16"
ENGINE HONDA GX120K1 3/4" KEYED SHAFT
GUARD
1
1
1
2
CAP, GREASE PLASTIC
WASHER,SLOTTED HEX 10 x1/2
TYPE “F” SELF TAPPING MACH. SCREWS
WASHER, RETAINING
60
3053317
2
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA— PUMP ASSY. (CONT.)
PUMP ASSY. (CONT.)
PAGE 34 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MQ-D306HA — PUMP ASSY. (CONT.)
PUMP ASSY. (CONT.)
NO.
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
83
84
85
PART NO.
2023212
3054847B
2020316
3065581
3065583
2025656
2021211
3053416
2021232
3064779
3063327
3063320A
306W274A
2023800
306A0100310200
3055160
2022676C
306606075Y
2025111
PART NAME
QTY. REMARKS
SCREW, MACHINE FLT HD 10-32x1/2
CONNECTING RODTOP
FITTING, GREASE 3/16 STR
CONNECTING ROD BEARING
CRANK ARM
6
1
1
1
1
1
1
3
1
1
1
2
2
4
2
8
8
2
4
2
2
2
4
4
SCREW SOCKET SET 5/16"-18x5/16" L.G.
SCREW HEX 1/2"x1-1/2" 13UNC
NUT, HEX JAM LOCK NYLON 3/4-16"UNF
OIL SEAL
STUB AXLE
BUMPER
TOWING POLE
WHEEL 8 X 1.75 SEMI-PNEUMATIC
WASHER, LOCK
SCREW, HEX 5/16"-18 x 2, HN, LW
WASHER, FLAT 5/16"
WASHER, SLOTTED HOLE 1/32”THK.
WASHER, FLAT 3/8 SAE
NUT, HEX 5/16" 18 UNC
306A0100310225
306A0100500250
306H7200180125Z
306EC400037
306A0100370125
5/16-18 X 2-1/4, SCREW, HEX, HN, LW
SCREW, HEX 1/2" 12 X 2-1/2”, LW
COTTER PIN 3/16” O.D. X 1-1/4”
NUT, 3/8"-16
SCREW, HEX 3/8”-16 X 1-1/4”
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 36 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
*
4
PART NO.
PART NAME
QTY.
REMARKS
16271ZE1000
17210ZE0505
17218ZE0505
17230ZE0820
17232891000
17238ZE0010
17239ZE1000
17410ZE0030
90325044000
957010602000
9405006000
GASKET, ELBOW
1
ELEMENT, AIR CLEANER (DUAL) ................... 1.............INCLUDES ITEMS W/
FILTER, OUTER
COVER, AIR CLEANER (DUAL)
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW, AIR CLEANER ................................... 1.............INCLUDES ITEMS W/
WINGNUT, TOOL BOX SETTING
BOLT, FLANGE 6X20
*
1
1
1
2
1
5
*
7
8
9
#
#
#
12
13
14
2
1
2
NUT, FLANGE 6MM
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 38 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
QTY.
REMARKS
14100ZE0812
14410ZE0010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF0010
14721ZF0000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE0010
90012ZE0010
90206ZE1000
CAMSHAFT ASSEMBLY.................................. 1.............INCLUDES ITEMS W/
*
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
2
2
2
2
1
1
1
2
1
1
1
1
2
2
5
6
*
7
8
VALVE, EX.
SPRING, VALVE
9
10
11
12
13
14
15
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
NUT, PIVOT ADJ.
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 40 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
*
2
*
3
*
4
*
5
*
6
*
7
*
8
*
9
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE1811
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH7W51
16124ZE0005
16166ZH7W50
16173001004
16211ZE0000
16212ZH7800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1812
16954ZE1811
16956ZE1811
16957ZE1812
16967ZE0811
93500030080G
9430520122
GASKET SET
1
1
1
1
1
1
1
1
VALVE SET, FLOAT
FLOAT SET
CHAMBER SET, FLOAT
SCREW SET
SCREW SET, DRAIN
SCREW SET B
CHOKE SET
CARBURETOR ASSEMBLY, BE60B B............. 1.............INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
GASKET, FUEL STRAINER CUP
INSULATOR, CARBURETOR
GASKET, INSULATOR
SPACER, CARBURETOR
GASKET, CARBURETOR
*
10
1
1
1
1
1
1
1
*
11
*
12
*
13
14
15
16
17
LEVER, CHOKE (STANDARD) ......................... 1.............INCLUDES ITEMS W/+
LEVER,VALVE
18
1
1
1
1
1
2
1
1
1
1
1
*
19
*
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN (3 X 6)
PIN, SPRING (2 X 12)
JET, MAIN (#55) (OPTIONAL)
JET, MAIN (#58) (OPTIONAL)
JET, MAIN (#60)
20
*
21
*
22
*
23
*
24
25
25
25
26
#
99101ZH80550
99101ZH80580
99101ZH80600
99204ZE00350
*
*
JET, SET, PILOT (#35)
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 42 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
3
4
5
6
PART NO.
PART NAME
QTY.
REMARKS
16500ZH7820
16551ZE0010
16555ZE0000
16561ZE0020
16562ZE0020
16571ZH7000
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH7810
16584883300
16592ZE1810
90013883000
90015ZE5010
90022888010
90114SA0000
93500050250H
93500050160A
9405006000
CONTROL ASSEMBLY (REMOTE) ........... 1 ............ INCLUDES ITEMS W/
#
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
LEVER, CONTROL
SPRING, LEVER
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE CONTROL
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE 6X12 (CT200)
BOLT, GOVERNOR ARM
BOLT, FLANGE 6X20 (CT200)
NUT, SELF- LOCK 6MM
SCREW, PAN 5X25
1
1
1
1
1
1
1
7
8#
#
9
10
11
12
14
15
16
18
19
20
21
24
25
26
#
#
#
#
#
#
1
1
1
1
1
1
1
1
1
1
#
#
#
SCREW, PAN
NUT, FLANGE 6MM
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 44 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
1
2
PART NO.
PART NAME
QTY.
REMARKS
11300ZE0640
11381ZH7800
15600ZE1003
15600ZG4003
15625ZE1003
15625ZE1003
90015883000
91001878003
91203ZE0003
9430108140
COVER ASSEMBLY, CRANKCASE (W- TYPE)....... 1 ..............INCLUDES ITEMS W/
*
#
GASKET, CASE COVER
CAP ASSEMBLY, OIL FILLER ................................ 1 ..............INCLUDES ITEMS W/
CAP ASSEMBLY, OIL FILLER ................................ 1 ..............INCLUDES ITEMS W/+
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
BOLT, FLANGE 6X28
BEARING, RADIAL BALL
OIL SEAL 22X41X6
1
3
4
7#
1
1
7
1
1
2
8+
9
10
*
11
12
*
PIN A, DOWEL 8X14
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 46 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
1
2
PART NO.
13310ZE0601
90745ZE1600
PART NAME
CRANKSHAFT, H-TYPE
KEY 4.78 X4.78X38
QTY.
1
1
REMARKS
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 48 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
2
3
PART NO.
PART NAME
QTY.
REMARKS
120A0ZH7810
15510ZE1033
16510ZE1000
16511ZE1000
16512ZE1000
16513ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
90451ZE1000
90601ZE1000
90602ZE1000
91001878003
91202ZE6003
91353671003
9405010000
CYLINDER ASSEMBLY (OIL ALERT) ........1 ............ INCLUDES ITEMS W/
*
#
SWITCH ASSEMBLY, OIL LEVEL
GOVERNOR ASSEMBLLY .........................1 ............ INCLUDES ITEMS W/
1
4
5#
6#
7#
8
9
WEIGHT, GOVERNOR
HOLDER, GOVERNORWEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER, THRUST 6mm
WASHER, DRAIN PLUG 10.2mm
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL 62/22
OIL SEAL 22X35X6
O- RING 13.5X1.5 (ARAI)
NUT, FLANGE 10mm
2
1
2
1
1
2
1
2
1
1
1
1
1
2
1
2
10
11
12
13
14
15
16
17
18
19
20
*
*
9410106800
9425108000
957010601200
WASHER, PLAIN 6mm
PIN, LOCK 8mm
BOLT, FLANGE 6X12
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 50 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12210ZH7000
12204ZE1306
12205ZE1315
12216ZE5300
12251ZH7800
12310ZE1000
12310ZE1010
12391ZE1000
15721ZH8000
90013883000
90043ZE1020
90047ZE1000
9430110160
CYLINDER HEAD ..................................................1.............. INCLUDES ITEMS W/
*
2
3
GUIDE, VALVE (OS) OPTIONAL
GUIDE, EX. VALVE (OS) OPTIONAL ................... 1.............. INCLUDES ITEMS W/+
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER, HEAD
COVER, HEAD
GASKET, CYLINDER HEAD COVER
TUBE, BREATHER
BOLT, FLANGE 6X12 (CT200)
BOLT, STUD 6X109
1
*
*
4 +
1
1
1
1
1
1
4
2
2
2
4
1
*
5
6
6
7
8
9
10
11
12
14
15
BOLT, STUD 8X32
PIN, A, DOWEL 10X16
BOLT, FLANGE 8X55
SPARK PLUG BPR6ES (NGK)
957230805500
9807955846
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 52 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
1
2
3
4
5
6
7
7
8
9
10
11
13
PART NO.
PART NAME
QTY.
REMARKS
11347371300
19610ZE0000ZE
19611ZH7810
90601ZH7013
19630ZH7000
32197ZH8003
36100ZE1015
36100ZH7003
36101ZE1010
90013883000
90022888010
34150ZH7003
957010600800
GROMMET, ADJUSTING COVER
COVER, FAN *NH1* BLACK
PLATE, SIDE (OIL ALERT)
CLIP, HARNESS
1
1
1
1
1
1
1
1
1
6
1
1
1
SHROUD
SUB- HARNESS
SWITCH ASSEMBLY, ENGINE STOP
SWITCH ASSEMBLY, ENGINE STOP
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6X12 (CT200)
BOLT, FLANGE 6X12 (CT200)
ALERT UNIT, OIL
BOLT, FLANGE 6X8
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 54 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
5
PART NO.
PART NAME
KEY, SPECIAL WOODRUFF 25X18
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
NUT, SPECIAL 14MM
QTY.
REMARKS
13331357000
19511ZE0000
28451ZH8003
31100ZE0010
90201878003
1
1
1
1
1
7
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 56 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
5
PART NO.
PART NAME
RUBBER, SUPPORTER 107MM
JOINT, FUEL TANK
TANK, FUEL *NH1* (BLACK)
CAP, FUEL FILLER ..................................... 1 .......... INCLUDES ITEMS W/
GASKET, FUEL FILLER CAP
O- RING 13.5X1.5 (ARAI)
NUT, FLANGE 6MM
BULK HOSE, FUEL (4.5X3000) (4.5X140)
CLIP, TUBE (B8)
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE0020ZD
17620ZH7023
17631ZH7003
91353671003
9405006000
1
1
1
*
6
1
1
2
1
2
1
*
11
12
13
14
15
950014500360M
9500202080
90004ZH7003
BOLT, FLANGE 6X29
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 58 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
PART NO.
PART NAME
QTY.
REMARKS
30500ZE1033
30700ZE1013
90121952000
COIL ASSEMBLY, IGNITION
CAP ASSEMBLY, NOISE SUPPRESSOR
BOLT, FLANGE 6X25
1
1
2
8
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 60 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
3
7
10
13
PART NO.
PART NAME
QTY.
REMARKS
18310ZF1000
18320ZF1H01
18381ZH8800
90050ZE1000
94001080000S
MUFFLER
1
1
1
4
2
PROTECTOR, MUFFLER
GASKET, MUFFLER
SCREW, TAPPING 5X8
NUT, HEX. 8MM
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 62 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.
PART NAME
QTY. REMARKS
13010ZK7V01
13011ZE6013
13012ZK7V01
13013ZK7V01
13101ZH7000
13102ZH7000
13103ZH7000
13104ZH7000
13111ZE0000
132A0ZE0000
13200ZE0000
90001ZE1000
90551ZE0000
RING SET, PISTON (STANDARD)
RING SET, PISTON (OS 0.25), OPTIONAL
RING SET, PISTON (OS 0.50) , OPTIONAL
RING SET, PISTON (OS 0.75), OPTIONAL
PISTON, STANDARD
1
1
1
1
1
1
1
1
1
PISTON, OS 0.25
PISTON, OS 0.50
PISTON, 0.75
PIN, PISTON
ROD ASSY, CONNECTING (UNDER SIZE) .... 1 ...... INCLUDES ITEMS W/
ROD ASSEMBLY, CONNECTING.................... 1 ...... INCLUDES ITEMS W/
BOLT, CONNECTING ROD
CLIP, PISTON PIN 13MM
*
*
2
2
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 64 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
28400ZH8013ZB
28410ZH8003ZB
28420ZH8013
28422ZH8013
28433ZH8003
28441ZH8003
28442ZH8003
28443ZH8003
28461ZH8003
28462ZH8003
90003ZH8003
9008ZE2003
STARTER ASSY., RECOIL *NH1* (BLACK) .......... 1.............. INCLUDES ITEMS W/
*
2
CASE, RECOIL STARTER *NH1* (BLACK)
REEL, RECOIL STARTER
RATCHET, STARTER
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
1
1
2
1
1
1
2
1
1
1
3
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
*
12
BOLT, FLANGE 6X10
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — GASKET KIT ASSY.
NO ARTWORK AVALIBLE
PAGE 66 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX120K1QX2 ENGINE — GASKET KIT ASSY.
GASKET KIT ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
2
06111ZH7405
11381ZH7800
12251ZH7800
12391ZE1000
16212ZH7800
16221ZH8801
18381ZH8800
GASKET KIT ......................................................... 1.............. INCLUDES ITEMS W/
*
3
*
4
*
5
*
6
*
7
*
8
*
GASKET, CASE COVER
GASKET, CYLINDER HEAD
GASKET, CYLINDER HEAD COVER
GASKET, INSULATOR
GASKET, CARBURETOR
GASKET, MUFFLER
1
1
1
1
1
1
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: February 22, 2006
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 68 — MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL — REV. #3 (01/09/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ-D306HA DIAPHRAGM PUMP — OPERATION AND PARTS MANUAL— REV. #3 (01/09/07) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
Tel. (800) 421-1244
Fax (800) 537-3927
Fax:800-672-7877
Fax:310-637-3284
310-537-3700
Contact: mq@multiquip.com
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technial Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
BRAZIL
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
© COPYRIGHT 2007, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are
the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MQ-D306HA Diaphragm Pump.
Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the
right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|
NEC Car Video System LCD1510+ User Manual
NEC Crib Toy l102w User Manual
NEC Projector LT220 User Manual
Nortel Networks Switch 42C4911 User Manual
Omnimount TV Video Accessories ECHO 50LE User Manual
Optoma Technology Projector TW330 User Manual
Orange Micro Radio B31100004 B User Manual
Oreck Vacuum Cleaner XL7 605 EYB User Manual
Panasonic Battery Charger EY0230 User Manual
Panasonic Electric Shaver ES7036 User Manual