AT Commands
For CDMA Wireless Modems
Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Contents
Chapter 1 - Introduction .....................................................................................................................................11
Scope of This Document................................................................................................................................11
Related References .......................................................................................................................................11
Definitions ......................................................................................................................................................12
Chapter 2 - AT Command Features ...................................................................................................................14
Line Settings ..................................................................................................................................................14
Command Line...............................................................................................................................................14
Information Responses and Result Codes.....................................................................................................14
Chapter 3 - Unsolicited AT Result Codes..........................................................................................................15
Cell Broadcast Message Directly Displayed +CBM.......................................................................................15
Cell Broadcast Message Stored in Memory +CBMI......................................................................................15
Cell Environment Description Indication +CCED ..........................................................................................15
Call Waiting Indication +CCWA ....................................................................................................................16
SMS Status Report Indication Directly Displayed +CDS...............................................................................16
SMS Status Report Indication Stored in Memory +CDSI ..............................................................................16
Key Press or Release +CKEV ......................................................................................................................17
Caller ID Presentation +CLIP........................................................................................................................17
Incoming Message Directly Displayed +CMT ...............................................................................................17
Incoming Message Stored in Memory +CMTI...............................................................................................18
Mode Preference +COPS .............................................................................................................................18
Registration & Roaming +CREG...................................................................................................................18
Incoming Call +CRING..................................................................................................................................19
RxLev Indication +CSQ.................................................................................................................................19
Incoming Call +RING ....................................................................................................................................19
Call Answered +WANS.................................................................................................................................20
Call Connected +WCNT................................................................................................................................20
Call Ended +WEND ......................................................................................................................................20
Feature Notification Message +WFNM .........................................................................................................21
Flash Indication +WFSH ...............................................................................................................................21
General Indicator +WIND..............................................................................................................................22
Call Originated +WORG................................................................................................................................23
Call Privacy Indication +WPRV.....................................................................................................................23
Roaming Indication +WROM ........................................................................................................................24
Emergency Mode +WSOS............................................................................................................................24
Current NAM Change +WNAM.....................................................................................................................25
Voice Mail Indicator +WVMI..........................................................................................................................25
SMS Message Storage Full +WMGF............................................................................................................25
Power Save +WSPS.....................................................................................................................................26
Chapter 4 - General Commands.........................................................................................................................27
Request Revision Identification +CGMR.......................................................................................................27
Electronic Serial Number +CGSN.................................................................................................................27
Select TE Character Set +CSCS ..................................................................................................................27
Request IMSI +CIMI......................................................................................................................................28
Capabilities List +GCAP................................................................................................................................28
Repeat Last Command A/.............................................................................................................................28
Phone Offline +CPOF ...................................................................................................................................28
Set Phone Functionality +CFUN...................................................................................................................29
Phone Activity Status +CPAS .......................................................................................................................30
Report Mobile Equipment Errors +CMEE .....................................................................................................30
Keypad Control +CKPD ................................................................................................................................30
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Clock Management +CCLK ..........................................................................................................................31
Ring Melody Playback +CRMP.....................................................................................................................31
Ringer Sound Level +CRSL..........................................................................................................................32
Subscriber Number +CNUM .........................................................................................................................32
Select Type of Address +CSTA ....................................................................................................................32
View Modem Timers +WTMR.......................................................................................................................33
Modem Serial Number +WMSN....................................................................................................................33
Chapter 5 - Call Control Commands..................................................................................................................34
Dial Command D...........................................................................................................................................34
Hang-Up Command H ..................................................................................................................................35
Answer a Call A ............................................................................................................................................36
Remote Disconnection...................................................................................................................................36
Extended Error Report +CEER.....................................................................................................................36
DTMF Signals +VTD, +VTS.........................................................................................................................37
DTMF START and STOP Continuous +WSDT, +WSDS.............................................................................37
Redial Last Telephone Number DL...............................................................................................................38
Automatic Dialing with DTR %Dn..................................................................................................................38
Automatic Answer S0....................................................................................................................................38
Incoming Call Bearer +CICB.........................................................................................................................39
Single Numbering Scheme +CSNS ..............................................................................................................39
Microphone Gain +VGT ................................................................................................................................40
Volume Gain Control +VGR..........................................................................................................................40
Microphone Mute Control +CMUT ................................................................................................................41
Speaker & Microphone Selection +SPEAKER..............................................................................................41
Echo Cancellation +ECHO............................................................................................................................42
Side Tone Modification +SIDET....................................................................................................................42
Initialize Voice Parameters +VIP...................................................................................................................43
TTY Mode +WTTY........................................................................................................................................43
Chapter 6 - Network Service Commands..........................................................................................................44
Signal Quality +CSQ.....................................................................................................................................44
Mode Preference +COPS .............................................................................................................................44
Band Preference +WBND.............................................................................................................................45
Roam Preference +WRMP ...........................................................................................................................46
Network Registration & Roaming +CREG.....................................................................................................47
Change NAM Selection +WNAM ..................................................................................................................48
Read Current NAM +WCNM.........................................................................................................................48
Emergency Mode +WSOS............................................................................................................................49
Extended Roam Indication +WRMW.............................................................................................................50
Chapter 7 - SIM Card Operational Commands..................................................................................................51
Enter PIN +CPIN...........................................................................................................................................51
Enter PIN2 +CPIN2.......................................................................................................................................52
PIN Remaining Attempt Number +CPINC.....................................................................................................52
Facility Lock +CLCK......................................................................................................................................53
Change Password +CPWD...........................................................................................................................54
Card Identification +CCID .............................................................................................................................54
Chapter 8 - Short Messages Commands ..........................................................................................................55
Parameters Definition ....................................................................................................................................55
Select Message Service +CSMS..................................................................................................................56
New Message Acknowledgement +CNMA ...................................................................................................56
Preferred Message Storage +CPMS.............................................................................................................57
Show Text Mode Parameters +CSDH ..........................................................................................................57
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
New Message Indication +CNMI...................................................................................................................58
Read Message +CMGR................................................................................................................................59
List Message +CMGL ...................................................................................................................................61
Send Message +CMGS ................................................................................................................................62
Write Message to Memory +CMGW .............................................................................................................63
Send Message From Storage +CMSS..........................................................................................................63
Delete Message +CMGD..............................................................................................................................64
Select Broadcast Messages +CSCB.............................................................................................................65
Message Status Modification +WMSC..........................................................................................................65
Message Overwriting +WMGO .....................................................................................................................66
Change SMS Status +WUSS........................................................................................................................66
Set SMS Compose Language and Encoding +WSCL ..................................................................................67
Set Timestamp of MT SMS +WSTM.............................................................................................................67
Chapter 9 - Supplementary Services Commands ............................................................................................68
Call Forwarding +CCFC................................................................................................................................68
Calling Line Identification Restriction +CLIR.................................................................................................69
Calling Line Identification Presentation +CLIP..............................................................................................69
Send Flash to Base Station +WFSH.............................................................................................................70
List Current Call State +CLCC......................................................................................................................71
Chapter 10 - Data Commands ............................................................................................................................72
Using AT Commands During a Data Connection...........................................................................................72
Select Mode +FCLASS.................................................................................................................................72
Cellular Result Codes +CRC ........................................................................................................................73
DTE-DCE Local Rate Reporting +ILRR ........................................................................................................73
V42 Bis Data Compression +DS...................................................................................................................74
V42 Bis Data Compression Report +DR.......................................................................................................75
Chapter 11 – V.24-V.25 Commands ...................................................................................................................76
Fixed DTE Rate +IPR ...................................................................................................................................76
DTE-DCE Character Framing +ICF ..............................................................................................................76
DTE-DCE Local Flow Control +IFC...............................................................................................................77
Set DCD Signal &C.......................................................................................................................................77
Set DTR Signal &D .......................................................................................................................................78
Set DSR Signal &S .......................................................................................................................................78
Back to Online Mode O.................................................................................................................................78
Result Code Suppression Q..........................................................................................................................78
DCE Response Format V..............................................................................................................................79
Auto-Tests &T...............................................................................................................................................79
Echo E ..........................................................................................................................................................79
Display Configuration &V..............................................................................................................................80
Request Identification Information I...............................................................................................................81
Restore Factory Setting &F...........................................................................................................................81
Save Configuration &W.................................................................................................................................81
Chapter 12 - Phone Book Commands...............................................................................................................82
Select Phonebook Memory Storage +CPBS.................................................................................................82
Return Selected Phonebook Locations +CPBU............................................................................................83
Find Phonebook Entries +CPBF...................................................................................................................83
Write Phonebook Entry +CPBW ...................................................................................................................84
Phonebook Read +CPBR .............................................................................................................................85
Phonebook Search +CPBP...........................................................................................................................85
Avoid Phonebook Init +WAIP........................................................................................................................86
Delete Calls From Phonebook +WDCP ........................................................................................................86
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 13 - Position Determination .................................................................................................................87
(GPS) AT Commands..........................................................................................................................................87
Position Determination Session Type +WPDST ...........................................................................................87
Position Determination Operating Mode +WPDOM ......................................................................................88
Position Determination Data Download +WPDDD........................................................................................88
Position Determination Fix Rate +WPDFR ...................................................................................................89
Position Determination Privacy Level +WPDPL............................................................................................89
Position Determination NV Privacy Level +WPPRV......................................................................................89
Position Determination Transport Setting +WPTLM......................................................................................90
Position Determination Start Session +WPDSS ...........................................................................................91
Position Determination End Session +WPDES.............................................................................................91
Position Determination Start Session Result +WPDSS ................................................................................92
Set IP Address of gpsOne Session +WPDIP................................................................................................93
Set Port of gpsOne Session +WPDPT..........................................................................................................93
Chapter 14 - Specific AT Commands ................................................................................................................94
Manufacturer Identification +WGMI...............................................................................................................94
Request Model Identification +WGMM..........................................................................................................94
Cell Environment and RxLev Indication +CCED...........................................................................................94
Analog Digital Converters Measurements +ADC..........................................................................................96
Mobile Equipment Event Reporting +CMER.................................................................................................96
Read GPIO Value +WIOR ............................................................................................................................97
Write GPIO Value +WIOW............................................................................................................................97
Play Tone +WTONE .....................................................................................................................................98
Play DTMF Tone +WDTMF ..........................................................................................................................99
Hardware Version +WHWV ..........................................................................................................................99
Select Voice Gain +WSVG .........................................................................................................................100
Status Request +WSTR..............................................................................................................................100
Ring Indicator Mode +WRIM.......................................................................................................................101
32kHz Sleep Mode +W32K.........................................................................................................................101
Change Default Melody +WCDM................................................................................................................102
Software Version +WSSW..........................................................................................................................102
Custom Character Set +WCCS ..................................................................................................................103
CPHS Command +CPHS ...........................................................................................................................104
Change Default Player +WCDP..................................................................................................................104
Reset +WRST.............................................................................................................................................105
Set Standard Tone +WSST ........................................................................................................................105
Set Voice Privacy Level +WPRV.................................................................................................................106
Security PIN +WPIN....................................................................................................................................107
Request PRL Version Information +WPRL .................................................................................................108
Minute Alert +WMBP...................................................................................................................................108
Configure LED Indicator +CLED.................................................................................................................109
Keypad Enable/Disable +WPAD.................................................................................................................110
Chapter 15 - SIM TOOLKIT ...............................................................................................................................111
Overview of SIM Application ToolKit............................................................................................................111
Messages Exchanged During a SIM ToolKit Operation...............................................................................112
SIM ToolKit Set Facilities (+STSF)..............................................................................................................114
Error Codes..................................................................................................................................................115
SIM ToolKit Indication (+STIN) ...................................................................................................................115
Last SIM Toolkit Indication:..........................................................................................................................116
SIM ToolKit Get Information +STGI) ...........................................................................................................117
Unsolicited Result: SIM ToolKit Control Response (+STCR)......................................................................120
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SIM ToolKit Give Response (+STGR).........................................................................................................121
Chapter 16 - Provisioning AT Commands ......................................................................................................124
Service Programming Code +WSPC ..........................................................................................................124
Mobile Directory Number +WMDN..............................................................................................................124
Set IMSI +WIMI...........................................................................................................................................125
SID and NID +WSID ...................................................................................................................................125
Access Overload Class +WAOC.................................................................................................................126
Slot Cycle Index +WSCI..............................................................................................................................126
Primary Browser Gateway +WBGP ............................................................................................................126
Secondary Browser Gateway +WBGS........................................................................................................126
Packet Dial String +WPDS..........................................................................................................................127
Primary CDMA Channels +WPCC..............................................................................................................127
Secondary CDMA Channels +WSCC .........................................................................................................127
Service Option Management +WSOM........................................................................................................128
Commit Changes +WCMT..........................................................................................................................128
Read SID/NID Entries +WSNR...................................................................................................................129
Service Programming Example....................................................................................................................130
Chapter 17 - Extended AT Commands in IS707.3...........................................................................................131
Remote Async/Fax Command X.................................................................................................................131
Reset to Default Configuration Z0...............................................................................................................131
Select Tone Dialing T..................................................................................................................................131
Select Pulse Dialing P.................................................................................................................................132
Basic S-Registers S<X>..............................................................................................................................132
Error Control Operation +EB.......................................................................................................................133
Numeric Parameter Control +EFCS............................................................................................................133
Error Control Report +ER............................................................................................................................134
Error Control Selection +ES........................................................................................................................134
Error Control Selection +ESR .....................................................................................................................135
Error Control Selection +ETBM...................................................................................................................135
Request Manufacture Identification +GMI...................................................................................................136
Request Manufacture Identification +GMM.................................................................................................136
Request Revision Identification +GMR .......................................................................................................136
Request Product Serial Number Identification +GSN..................................................................................137
Request Global Object Identification +GOI .................................................................................................137
Modulation Selection +MS ..........................................................................................................................137
Modulation Automode Control +MA............................................................................................................138
Modulation Reporting Control +MR.............................................................................................................138
V.18 Reporting Control +MV18R.................................................................................................................138
V.18 Selection +MV18S..............................................................................................................................139
Cellular Extension +CXT.............................................................................................................................139
Configuration String +CFG..........................................................................................................................140
Query Service +CAD...................................................................................................................................140
Um Interface Data Compression Reporting +CDR.......................................................................................140
Um Interface Data Compression +CDS........................................................................................................141
Set Rm Interface Protocol +CRM................................................................................................................141
Battery Charge +CBC .................................................................................................................................142
Command State Inactivity Timer +CQD......................................................................................................142
Mobile Station IP Address +CMIP...............................................................................................................142
Base Station IP Address +CBIP..................................................................................................................143
Serving System +CSS ................................................................................................................................144
Select Multiplex Option +CMUX..................................................................................................................145
Um Interface Fax Compression +CFC .........................................................................................................145
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Hang-up Voice +CHV..................................................................................................................................146
Dial Command for Voice Calls +CDV..........................................................................................................146
IWF Content List +CGCAP .........................................................................................................................146
IWF Device Identification +CGOI................................................................................................................147
Um Packet Data Inactivity Timer +CTA........................................................................................................147
Chapter 18 – Fax Parameters...........................................................................................................................148
Chapter 19 - Qualcomm Defined AT Commands for CDMA Operation ........................................................150
Transition to Diagnostics Monitor $QCDMG ...............................................................................................150
Quick Net Connect $QCQNC......................................................................................................................150
Protocol Revision in Use $QCPREV...........................................................................................................151
Originate M-to-M Packet Data Call $QCMTOM ..........................................................................................151
Dump RLP Protocol Statistics $QCRLPD ...................................................................................................151
Reset RLP Protocol Statistics $QCRLPR ...................................................................................................152
Dump PPP Protocol Statistics $QCPPPD...................................................................................................152
Reset PPP Protocol Statistics $QCPPPR...................................................................................................152
Dump IP Protocol Statistics $QCIPD ..........................................................................................................152
Reset IP Protocol Statistics $QCIPR ..........................................................................................................153
Dump UDP Protocol Statistics $QCUDPD..................................................................................................153
Reset UDP Protocol Statistics $QCUDPR ..................................................................................................153
Dump TCP Protocol Statistics $QCTCPD...................................................................................................153
Reset TCP Protocol Statistics $QCTCPR...................................................................................................154
Set Data Service Option $QCSO................................................................................................................154
Clear Mobile Error Log $QCCLR ................................................................................................................154
Answer Incoming Voice Call $QCCAV........................................................................................................155
Automatic Packet Detection $QCPKND......................................................................................................155
Pre-arrangement Setting $QCVAD.............................................................................................................155
Set DM Baud Rate $QCDMR......................................................................................................................156
Set Medium Data Rate $QCMDR ...............................................................................................................156
Dump RLP 3 Protocol Statistics $QCRL3D.................................................................................................156
Reset RLP 3 Protocol Statistics $QCRL3R.................................................................................................157
SCRM’ing Selection $QCSCRM .................................................................................................................157
R-SCH Selection $QCTRTL........................................................................................................................157
R-SCH Selection $QCMIP ..........................................................................................................................158
MIP Selection $QCMIPP.............................................................................................................................159
RFC2002bis Selection $QCMIPT ...............................................................................................................159
Current Active Profile $QCMIPEP...............................................................................................................159
Return Profile Information $QCMIPGETP...................................................................................................160
Set NAI for Active Profile $QCMIPNAI........................................................................................................160
Set Reverse Tunneling $QCMIPRT............................................................................................................161
Set MN-AAA Shared Secrets $QCMIPMASS .............................................................................................161
Set MN-HA Shared Secrets $QCMIPMHSS ...............................................................................................162
Set MN-AAA Shared Secrets $QCMIPMASSX...........................................................................................162
Set MN-HA Shared Secrets $QCMIPMHSSX.............................................................................................163
Set MN-AAA Shared Secrets $QCMIPMASPI ............................................................................................163
Set MN-HA Shared Secrets $QCMIPMHSPI ..............................................................................................164
Set Primary HA IP Address $QCMIPPHA...................................................................................................164
Set Secondary HA IP Address $QCMIPSHA..............................................................................................165
Set Home HA IP Address $QCMIPHA........................................................................................................165
Chapter 20 - Reference Information ................................................................................................................166
MS Error Result Code : +CME ERROR: <error> .........................................................................................166
Message Service Failure Result Code: +CMS ERROR :<error> .................................................................167
Specific Error Result Codes.........................................................................................................................167
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Extended Error Report (+CEER) Call Processing Codes.............................................................................167
Final Result Codes.......................................................................................................................................167
Intermediate Result Codes...........................................................................................................................168
Parameters Storage.....................................................................................................................................168
Codes for SMS-STATUS-REPORT (+CDS and +CMGR) ...........................................................................169
Code Meaning..............................................................................................................................................169
AT Commands Supported When SIM Card Removed.................................................................................170
AT Commands for AMPS Operation............................................................................................................170
Chapter 21 - AT Command Examples .............................................................................................................171
Example 1: When the MS Has Already Been Powered On..........................................................................171
Examples Where a Voice Call is Originated.................................................................................................171
Example with Incoming Calls .......................................................................................................................171
Example of a Call Waiting Situation.............................................................................................................172
Examples About Short Messages................................................................................................................172
Chapter 22 - Verizon® Specific AT Commands..............................................................................................174
SMS Status Report Indication Directly Displayed +CDS.............................................................................174
(Chapter 3)...................................................................................................................................................174
Incoming Message Directly Displayed +CMT (Chapter 3) ..........................................................................175
Roaming Indication +WROM (Chapter 3) ...................................................................................................175
Enhanced Roaming Indication +WERI........................................................................................................176
Emergency Mode +WSOS (Chapter 3)........................................................................................................177
Read message +CMGR (Chapter 8)............................................................................................................178
List Message +CMGL (Chapter 8) ..............................................................................................................180
Send Message +CMGS (Chapter 8) ...........................................................................................................181
Write Message to Memory +CMGW (Chapter 8) ........................................................................................182
Service Programming Code +WSPC (Chapter 16) .....................................................................................183
Verizon®. System Selection +WVSS..........................................................................................................183
Initial Programming Required +WOT0 ........................................................................................................184
Programming In Progress +WOT1..............................................................................................................184
Programming Successful +WOT2...............................................................................................................184
Programming Unsuccessful +WOT3...........................................................................................................184
Commit Successful +WOTC .......................................................................................................................184
SPL Unlocked +WOTS ...............................................................................................................................185
NAM Download Ok +WOTN .......................................................................................................................185
MDM Download Ok +WOTM ......................................................................................................................185
MSI Download Ok +WOTI...........................................................................................................................185
PRL Download Ok +WOTP.........................................................................................................................185
Excess SPC Failures +WLCK.....................................................................................................................186
Position Determination Lock Level +WPLCK..............................................................................................186
Chapter 23 - Sprint® Specific AT Commands ................................................................................................187
SMS Status Report Indication Directly Displayed +CDS.............................................................................187
(Chapter 3)...................................................................................................................................................187
Set Phone Functionality +CFUN.................................................................................................................188
Signal Quality +CSQ...................................................................................................................................188
Facility Lock +CLCK....................................................................................................................................189
Mobile Directory Number +WMDN..............................................................................................................190
Serving System +CSS ................................................................................................................................191
Packet Zone Identifier +PZID......................................................................................................................192
Boot URL +WBURL ....................................................................................................................................192
Trusted Domain +WTDMN..........................................................................................................................192
Proxy Address +WDPXY ............................................................................................................................193
WIOTA Connection Control +WIOTA..........................................................................................................193
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Sprint®. System Selection +WSSS.............................................................................................................193
IOTA Error +WOAE.....................................................................................................................................194
Preparing Data Services +WOAP...............................................................................................................194
Please Retry +WOAR .................................................................................................................................194
Display PRI Checksum +WSUM.................................................................................................................194
Reset MIN and MDN to factory defaults +WRMM.......................................................................................195
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 - Introduction
CHAPTER 1 - INTRODUCTION
The AT command set is one of the main interfaces for the modem to interact with an external application
layer. CDMA AT commands are defined in TIA/EIA/IS707.3. However, as the wireless applications increase,
TIA/EIA/IS707.3 is not sufficient. In addition, a lot of GSM applications already exist and GSM customers
would like to maintain the same interface in order to make no or minimum changes to the applications to be
used with CDMA modem. To meet the all these needs, CDMA AT command set is designed to cover:
1) IS707.3 AT commands;
2) GSM 07.07 when applicable;
3) GSM 07.05 when applicable,
4) ITU-T v25 when applicable;
5) Proprietary AT set;
6) Customer specific AT commands;
7) Qualcomm defined AT commands.
Please note that in several instances, the GSM 7.07 and 7.05 specifications could not be followed because
of fundamental differences between CDMA and GSM call processing behaviors. In these cases, minimal
changes were made to the GSM-related commands.
Scope of This Document
This document describes the CDMA AT command, its syntax, its responses, and result codes. It serves as
the reference for wireless application development based on the CDMA modem and for its integration and
testing. The intended audience is expected to be familiar with CDMA data services protocol and AT modem
commands.
This document is also intended for use in the North American market. SIM/R-UIM and its related AT
commands are not documented here.
Related References
This interface specification is based on the following recommendations or standards:
1. ETSI GSM 07.05: Digital cellular telecommunications system (Phase 2); Use of DTE-DCE interface for
Short Message Service (SMS) and Cell Broadcast Service (CBS)
2. ETSI GSM 07.07: Digital cellular telecommunications system (Phase 2); AT command set for GSM
Mobile Equipment (ME)
3. ITU-T Recommendation V.25 ter: Serial asynchronous automatic dialing and control
4. ETSI GSM 03.40: Digital cellular telecommunications system (Phase 2); Technical implementation of the
Short Message Service (SMS) Point-to-Point (PP)
5. ETSI GSM 03.38: Digital cellular telecommunications system (Phase 2); Alphabets and language-
specific information
6. ETSI GSM 04.80: Digital cellular telecommunications system (Phase 2): Mobile radio interface layer 3,
Supplementary service specification, Formats and coding
7. TIA/EIA/IS-707.3: Data Service Options for Wideband Spread Spectrum Systems: AT Command
Processing and the Rm Interface
8. Qualcomm Application Note (CL93-V0327-1 X10): AT COMMANDS FOR DMSS
9. IS-131: Data Transmissions Systems and Equipment – Extensions to Asynchronous Dialing and Control.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 - Introduction
Definitions
This is an alphabetical list of terms and acronyms used throughout this document and the CDMA cellular
industry.
2G:
Second Generation. All digital cellular systems developed to replace the first analog cellular
systems. )GSN and CDMA).
3G:
Third Generation. Next generation digital cellular systems designed to have high-speed data
access and higher voice capacity (W CDNA & CDNA2000).
CBM:
CDMA:
Cell Broadcast Message. Ah SMS message that is broadcast to all mobiles on the network
Code Division Multiple Access. CDMA is a spread spectrum, digital wireless modulation
scheme for cellular communications systems. It has approximately 3 times the voice
capacity of GSM networks. Se IS-95, IS-95B, IS-2000.
CDMA2000:
DCE:
See IS-2000.
Data Communications Equipment. This is the modem in the traditional serial communication
paradigm of a computer connected via two modems to another computer.
Data Terminal Equipment. This is the computer in the traditional serial communication
paradigm of a computer connected via two modems to another computer.
Dual Tone Multi-Frequency: A pre-defined set of tones sent over the air when keys are
pressed on the keypad.
DTE:
DTMF:
Handset (Path): The audio path (microphone & speaker) that connects to a traditional hand held telephone
receiver, usually dual balanced electrical lines.
Headset (Path): The audio path (microphone & speaker) that connects to an earpiece with a microphone,
usually single electrical lines.
IMSI:
International Mobile Station IS. This is an international 15 digital phone number that uniquely
identifies a mobile. IMSI=MCC + MNC + MIN.
IOTA:
IS-95:
IS-95A:
Internet Over The Air.
The first CDMA standard published by Qualcomm in 1993.
A CDMA standard with improved voice quality. This standard is widely used throughout the
world.
IS-95B:
This CDMA standard contains Medium Data Rate capabilities and bug fixes for system
access failures. It is considered a 2.5G system. This standard is mostly deployed in Korea.
The first 3G CDMA standard based on IS-95B. It contains a significant increase in voice
capacity and high-speed data rates. It is backward compatible with IS-95B and IS-95A. The
DCMA is IS-2000 compatible.
IS-2000:
IS-707:
TIA/EIA/IS-707 describes data services available on wideband spread spectrum systems. It
is organized into a series of related recommendations, some of which address functions
common to all CDMA data services and others that describe a specific data service.
Mobile Country Code. A pre-defined 30-digital number that represents a country in the IMSI.
Mobile IS Number: The traditional 10 digit phone number of the mobile.
Mobile Network Code. A pre-defined 2-digital number that represents a sub-network in the
IMSI (usually set to “00”).
MCC:
MIN:
MNC:
MO:
Mobile Originated. An action (usually a call) that is first started from the phone. An outgoing
call or SMS>
MS:
MT:
Mobile Station. The term MS is commonly used to represent the phone or mobile.
Mobile Terminated: An action usually a call) that is first started from a land based network.
An incoming call or SMS.
MSM:
NAM:
Mobile Station Modem. This is the main processing ASIC for a CDMA phone.
Number Assignment Modem. The NAM is collection of internal parameters that define a
working phone for a given network (phone number, access parameters, etc.).
Network ID. The NID is an identification number that represents geographic location of a
common coverage area; but is a subset of the SID, usually a neighborhood in a large city.
NID is usually not used and is set to zero. Also se SID
NID:
NV-RAM:
OTAPA:
Non-Volatile Random Access Memory, NV-RAM is a data storage device that does not lose
it’s data when power is turned off.
Over The Air Parameter Administration. An automatic update in internal software parameters
(PRL for example) by means of a specially defined CDMA data call that is mobile terminated
(MT).
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 - Introduction
OTASP:
PDU:
Over The Air Service Programming. An automatic update in internal software parameters
PRL for example) by means of a specially defined CDMA data call that is mobile terminated
(MT).
A GSM SMS standard where any type of binary data can be transported via an SMS
message. In the CDMA system, the PDU mode will not be supported; instead, the Unicode
format message is supported.
PN Offset:
Pseudorandom Noise Offset: In a CDMA network the PN offset is a variable time delay
offset of a repeating random noise generator that is used to distinguish individual sectors of
a base station.
P-REV:
PRL:
The CDMA revision of the mobile or base station.
Preferred Roaming List. The PRL is a collection of Frequencies, SIDs and NIDs that the call
processing software uses to search for approved and unapproved CDMA networks. The
PRL is loaded into the phone and is saved in NV-RAM.
PSTN:
RF:
Public Switching Telephone Network. The traditional telephone network.
Radio Frequency.
RSSI:
Receive Signal Strength Indicator: This parameter represents the total RF received signal
power from the base station(s) the mobile sees.
SID:
System ID. The SID is an identification number that represents geographic locations of a
common coverage area, usually a large city. Also see NID.
Short Messaging Service; A supplement service that is capable of sending and receiving
short length text messages to/from the mobile.
Terminal Application/Terminal Equipment. This is the end “device” (combination of hardware
and software) that communicates with a modem via a serial link. In this context, it is the
device (PDA/Computer) connected to the WISMO Quik. Also see DTE.
Type Of Number/Numbering Plan Identification.
SMS:
TA/TE:
TON/NPI:
V24-V25:
V42:
A data compression algorithm.
A data compression algorithm.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 – At Command Features
CHAPTER 2 - AT COMMAND FEATURES
Line Settings
A serial link handler is set with the following default values (factory settings): 115,200bps, 8 bits data, 1 stop
bit, no parity, RTS/CTS flow control.
Please use the +IPR, +IFC and +ICF commands to change these settings.
Command Line
Commands always start with AT (which means ATtention) and finish with a <CR> character.
Information Responses and Result Codes
Responses start and end with <CR><LF>, except for the ATV0 (response format) and the ATQ1 (result code
suppression) commands.
•
•
If command syntax is incorrect, an ERROR string is returned.
If extended error reports are enabled (+CMEE), the +CME ERROR: <Err> or +CMS ERROR: <SmsErr>
strings are returned with different error codes. Refer to the appendix for a definition of error codes and
their meanings.
•
If the command line has been performed successfully, an OK string is returned.
In the following examples <CR> and <CR><LF> are intentionally omitted.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
CHAPTER 3 - UNSOLICITED AT RESULT CODES
This section describes unsolicited AT codes that are sent to the modem as the result of an AT command or
network notification. These commands are used throughout the sections of this document. Refer to this
section for an explanation on any unsolicited command that is mentioned in the subsequent sections for
result code range and value definitions.
Cell Broadcast Message Directly Displayed +CBM
Description: This response indicates a Cell Broadcast message has been received and according to the
message storage preferences (+CNMI), is to be directly displayed.
Values:
<oa>
Originator Address
<scts>
Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
Type-of-Address of <oa>
<tooa>
<lang>
Language
<encod> Encoding method
<length> The number of characters in the following <data> field
<data>
Message contents
Syntax:
Response syntax: +CBM: <oa>, <scts>, [<tooa>,]<lang>,<encod>[,<length>]
<CR><LF><data>
Example Result
+CBM: “123456”,”98/10/01,12 :3000+00”,129,1,2,5<CR><LF>
Hello
Note: Cell broadcast message received
Cell Broadcast Message Stored in Memory +CBMI
Description: This response indicates a Cell Broadcast message has been received and according to the
message storage preferences (+CNMI), is to be stored in memory.
Values:
Syntax:
<mem>
<index>
NVRAM storage area (always “BC” for this response)
location of message within storage area
Response syntax: +CBMI: <mem>,<index>
Example Result
+CBMI: “BC”,5
Note: Cell broadcast message received and stored in “BC” memory at index 5
Cell Environment Description Indication +CCED
Description:
This response is used to return information that has been requested by the +CCED AT command. Refer to
the +CCED AT command in chapter 14 for more information and a definition of the returned values.
Syntax:
Response syntax: +CCED: <requested dump>
Example Result
+CCED: 1,725,4,65535,6,,0,,,-104,-35,-63
Note: Cell environment description indication in response to AT+CCED=0,1
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Call Waiting Indication +CCWA
Description: This response indicates that another incoming call is occurring during an existing call. See
+WFSH, Send Flash to Base Station in chapter 9 for information about handling call-waiting
situations
Values:
<caller_id>
<type>
Caller identification number
always 129 for this response
Syntax:
Response syntax: +CCWA: <caller_id>, <type>
Example Result
+CCWA: 18005551212,129
Note: Incoming call from 1-800-555-1212, type always equals 129.
SMS Status Report Indication Directly Displayed +CDS
Description: This response indicates an SMS status report has been received and according to the
message storage preferences (+CNMI), is to be directly displayed. +CDS is also used in the
data compression functionality as an active command. Refer to chapter 17 (Um Interface
Data Compression) for an explanation of +CDS usage for data compression.
Values:
<mr>
Message Reference
<ra>
Recipient Address
<tora>
<scts>
Type-of-Address of <ra>
Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
<dt>
Discharge Time in string format: “yy/MM/dd,hh :mm :ss±zz”
(Year [00-99], Month [01-12], Day [01-31], Hour, Minute, Second and Time Zone
[quarters of an hour] )
<st>
Status of a SMS-STATUS-REPORT (See Chapter 20)
Syntax:
Response Syntax: +CDS: <mr>, [<ra>] , [<tora>], <scts>,<dt>,<st> (Text mode)
Example Result
+CDS : 2, 116, ”3146290800”, 129, “98/10/01,12 :30 :07+04”, “98/10/01 12 :30 :08+04”, 0
Note: SMS status report received
SMS Status Report Indication Stored in Memory +CDSI
Description: This response indicates an SMS status report has been received and according to the
message storage preferences (+CNMI), is to be stored in memory.
Values:
Syntax:
<mem>
<index>
NVRAM storage area (always “SR” for this response)
location of message within storage area
Response syntax: +CDSI: <mem>,<index>
Example Result
+CDSI: “SR”,5
Note: SMS status report received and stored in “SR” memory at index 5
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Key Press or Release +CKEV
Description: This response indicates that a key has been pressed or released.
Values:
<key> Key input (0-9, *, #)
<press>
0: key release
1: key press
Syntax:
Response syntax: +CKEV: <key>,<press>
Example Result
+CKEV: 9,0
Note: Indicates key 9 has been released
Caller ID Presentation +CLIP
Description: This response indicates that caller ID information is available for the current incoming call.
See +CLIP, Calling Line Identification Presentation, in chapter 9, for enable and disabling
this result.
Values:
Syntax:
<caller_id> Caller identification number
<type> Always 129 for this response
Response syntax: +CLIP: <caller_id>, <type>
Example Result
+CLIP: 18005551212,129
Note: Incoming call from 1-800-555-1212, type always equals 129.
Incoming Message Directly Displayed +CMT
Description: This response indicates that an incoming message has been received and according to the
message storage preferences (+CNMI), is to be directly displayed.
Values:
<oa>
Originator Address.
<scts>
Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
Type-of-Address of <oa>
<tooa>
<lang>
Language
<encod> Encoding method
<priority>: Message priority:
0 – Normal
1 – Interactive
2 – Urgent
3 – Emergency
<cbn>
<length> The number of characters in the following <data> field
<data> Message contents
Call Back Number
Syntax:
Response syntax: +CMT: <oa>, <scts>, <tooa>, <lang>, <encod>, <priority> [,<cbn>],
<length> <CR><LF> <data> (text mode)
Example Result
+CMT: “123456”,”98/10/01,12 :3000+00”,129,1,2,0,”5550000”,5<CR><LF>
Hello
Note: Incoming message received
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Incoming Message Stored in Memory +CMTI
Description: This response indicates that an incoming message has been received and according to the
message storage preferences (+CNMI), is to be stored in memory.
Value:
<mem>
<index>
NVRAM storage area (always “MT” for this response)
location of message within storage area
Syntax:
Response syntax: +CMTI: <mem>,<index>
Example Result
+CMTI: “MT”,5
Note: Incoming message received and stored in “MT” memory at index 5
Mode Preference +COPS
Description: This response indicates that a change in mode preference has taken place. See +COPS,
Mode Preferences, in chapter 6 for information about Changing Mode Preference.
Values:
<mode> (For System Determination 2.0)
0: Automatic.
1: CDMA only.
2: CDMA or AMPS only.
3: Analog only.
<term>
0: Permanent – this mode persists until another +COPS command is issued
1: Power cycle – this mode persists until power cycle is performed
Syntax:
Response syntax: +COPS: <mode>,<term>
Example Result
+COPS:0,0
Note: Unsolicited +COPS result confirms Automatic mode is requested.
+COPS:2,0
Note: Unsolicited +COPS result confirms CDMA or AMPS only mode is requested.
Registration & Roaming +CREG
Description: This response indicates the current state of roaming. See +COPS, Mode Preferences, in
chapter 6 for information about Changing Mode Preference
Values:
<stat>
0: not registered, MS is not currently searching for a new operator.
1: registered, home network.
2: not registered, MS currently searching for a base station.
4: unknown.
5: registered, roaming
Syntax:
Response syntax: +CREG: <stat>
Example Result
+CREG: 1
Note: Modem has found the home network and is registered.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Incoming Call +CRING
Description: This response indicates an incoming call. See +CRC, Cellular Result Codes, in chapter 10
for information about enabling this result.
Values:
<type>
VOICE: normal voice call
DATA: all types of data calls
FAX: all types of fax calls
OTAPA: over the air parameter administration call
TEST: markov, loopback, or test call
Syntax:
Response syntax: +CRING: <Type>
Example Result
+CREG: VOICE
Note: Incoming normal voice call.
RxLev Indication +CSQ
Description: This response is used to return information that has been requested by the +CCED AT
command. Refer to the +CCED AT command in chapter 14 (Cell Environment and RxLev
Indication) for command usage information.
Values:
<rssi>:
0-31: Valid value ranges. Exact meaning of the value shall be manufacturer defined.
The lowest value is 0 and the highest is 31.
99: Represents signal quality unknown.
<fer>:
99: Not known or not detectable Currently always returns 99.
Syntax:
Response syntax: +CSQ: <rssi>,<fer>
Example Result
+CSQ: 29, 99
Note: RSSI notification
Incoming Call +RING
Description: This response indicates an incoming call.
Syntax:
Response syntax: +RING
Example Result
+RING
+RING
Note: Incoming Call
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Call Answered +WANS
Description: This response indicates that a voice call has been answered.
Values:
<call type>
0: incoming call
1: outgoing call answered by other party (only available on networks supporting
answering supervision for payphone applications)
Syntax:
Response syntax: +WANS:<call type>
Command
Possible Responses
ATA
+RING
OK
+WANS:0
Note: Incoming call answered
+WCNT:3
Call Connected +WCNT
Description: This unsolicited command indicates that an incoming or outgoing voice call has been
connected into a traffic channel state. If the service option is not available, +WCNT: will
output “NULL”.
Values:
<so> Service option of call.
Speech: 3, 17, 32768
Loopback: 2, 9, 55
OTAPA: 18, 19
Position Determination: 35, 36
Syntax:
Response syntax: +WCNT: <so>
Command
Possible Responses
ATD18005551212;
OK
+WORG:18005551212
+WCNT:3
Note: Call Connected with service option 3
Call Ended +WEND
Description: This response indicates that a voice call or attempt to establish a voice call has ended.
Values (for WISMO Quik 24xx) :
<reason>
0: Phone is offline
20: Phone is CDMA locked
21: Phone has no service
22: Call Faded/Dropped
23: Received Intercept from Base Station
24: Received Reorder from Base Station
25: Received a Release from Base Station (This is a normal call termination).
26: Service Option rejected by Base Station
27: Received Incoming Call
28: Received an alert stop from Base Station
29: Software ended the call (Normal release).
30: Received End Activation – OTASP calls only.
31: Internal Software aborted the origination/call.
32: Maximum Access probes exhausted (The modem failed to contact the Base Station)
34: RUIM not present
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
35: Origination already in progress
36: General Access Failure
37: Received retry order (IS-2000 only).
Syntax:
Response syntax: +WEND: <reason>
Command
Possible Responses
ATD18005551212;
OK
+WORG:18005551212
+WCNT:3
OK
ATH
+WEND:29
Note: Call Ended with a normal release
ATD18005551212;
OK
+WORG:18005551212
+WEND:22
Note: Call failed because the signal faded.
Feature Notification Message +WFNM
Description: This response displays a broadcast message that the carrier may send to all mobiles in an
emergency. This event is required for CDMA specifications.
Syntax:
Response Syntax: +WFNM=”<message>”
Command
Possible Responses
+WFNM=”Help, I have fallen and I can’t get up!”
Flash Indication +WFSH
Description: This response confirms that a flash has been sent to the base station. See +WFSH
command, Chapter 9, for more information on using flash commands.
Syntax:
Response Syntax: +WFSH
Command
Possible Responses
AT+WFSH
OK
+WFSH
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
General Indicator +WIND
Description: This is a general mechanism to send unsolicited non-standardized indications to the
application. The identified unsolicited non-standardized indications are:
•
•
Indication during mobile originated call setup that the calling party is ringing.
Indication of the availability of the product to receive AT commands after boot.
The +WIND is overloaded with two functionalities:
1) posts non-standardized indications and
2) allows the user to specify indication level. For each of these indications, a “bit flow” has
to be indicated.
Values:
<IndLevel>
1 (bit-0):
R-UIM Presence
2 (bit-1):
Reserved
4 (bit-2):
Reserved
8 (bit-3):
Indication that the product is ready to process all AT commands
16 (bit-4):
32 (bit-5):
64 (bit-6):
128 (bit-7):
256 (bit-8):
512 (bit-9):
Reserved
Reserved
Network service available indication
Network lost indication
Reserved
Reserved
1024 (bit-10): Corrupted RF calibration values (checksum mismatch)
Note 1: If <IndLevel> is equal to 0, no unsolicited “+WIND: <IndNb>” will occur.
Note 2: If <IndLevel> bit 10 is set, the modem will transition to OFFLINE mode.
A combination (addition of the values) is used to allow more than one indication flow. 0 < In
d Level ¡Ü 2047 For example: 128 (network lost indication) + 64 (network service available
indication) = 192.
The response is OK if the values are in the previous range.
The unsolicited response will then be: +WIND : <event>
Example Result
+WIND:8
Note: General indication that AT commands are ready to be accepted
The supported events are:
<event>
0:
R-UIM not present
1:
R-UIM present
2:
Reserved
4:
Reserved
16:
32:
64:
128:
256:
512:
Reserved
Reserved
The network service is available for an emergency call.
The network is lost.
Reserved
Reserved
1024: Corrupted RF calibration values (checksum mismatch)
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Syntax:
Command syntax: AT+WIND=<IndLevel>
Command
Possible Responses
AT+WIND?
WIND: 8
OK
Note: Show current setting.
AT+WIND=?
Note: Default 8. (9 if RUIM is present)
+WIND: (0-2047)
Note: Show <IndLevel> range.
OK
AT+WIND=128
OK
Note: Turn on Network lost indication only.
Note: Command accepted.
Call Originated +WORG
Description: This response indicates that an attempt to establish a voice call has occurred.
Syntax: Response Syntax: +WORG: <number>
Command
ATD1800555121
2;
Possible Responses
OK
+WORG:18005551212
+WCNT:3
OK
Note: <number> is the dialing string sent to the base station. You may see extra numbers before the
intended dialing string, this is a result of pre-pended numbers or other call options such as +CLIR.
Call Privacy Indication +WPRV
Description: This response confirms that the call privacy level has changed during a call.
Syntax:
Response Syntax: +WPRV: <prv>
Command
Possible Responses
AT+WPRV=1
OK
+WPRV: 1
<prv>
0: Indicates normal privacy
1: Indicates enhanced privacy
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Roaming Indication +WROM
Description: This response indicates that the roaming status has changed.
Syntax:
Response Syntax: +WROM: <roam>
Command
Possible Responses
+WROM:1
<roam>
0: Home.
1: Roam Icon ON (affiliated network)
2: Roam Icon Blink (foreign network)
The following values apply to enhanced roaming:
3: Out of Neighborhood
4: Out of Building
5: Roaming - Preferred System
6: Roaming - Available System
7: Roaming - Alliance Partner
8: Roaming - Premium Partner
9: Roaming - Full Service Functionality
10: Roaming - Partial Service Functionality
11: Roaming Banner On
12: Roaming Banner Off
13 – 63: Reserved for Standard Enhanced Roaming Indicator Numbers
64 – 127: Reserved for Non-Standard Enhanced Roaming Indicator Numbers
128 - 255: Reserved
Emergency Mode +WSOS
Description: This unsolicited command indicates a change in the status of Emergency Mode has taken
place. In the event that Emergency Mode is entered as the result of an emergency call, this
response will be sent to indicate that the modem is now in emergency mode. After this point,
to exit the modem out of Emergency Mode, an AT+WSOS or AT+COPS command must be
sent, which will result in a +WSOS response to confirm that Emergency Mode has been
exited. See +WSOS, section for more information about Emergency Mode.
Values:
The parameters values are the following ones:
<flag>
0: Emergency Mode Exited
1: Emergency Mode Entered
Syntax:
Response Syntax: +WSOS: <flag>
Command
Possible Responses
ATD911;
OK
Note: Make emergency call
+WSOS:1
+WORG:911
Note: Unsolicited +WSOS result confirms
Emergency Mode is entered
OK
AT+WSOS
Note: Exit Emergency Mode
+WSOS:0
Note: Unsolicited +WSOS result confirms
Emergency Mode is exited
OK
AT+COPS=0,0
Note: While in Emergency Mode, the mode
preference is changed, resulting in Emergency
Mode being exited
+WSOS:0
+COPS:0,0
Note: Unsolicited +WSOS result confirms
emergency mode exited and unsolicited +COPS
result confirms Automatic mode is requested
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Current NAM Change +WNAM
Description: This response indicates that the current NAM has changed.
Syntax:
Response Syntax: +WNAM: <nam>
Command
Possible Responses
+WNAM:2
<nam>
1: NAM 1
2: NAM 2
3: NAM 3
4: NAM 4
Voice Mail Indicator +WVMI
Description: This response indicates the status of the Voicemail Inbox.
Syntax:
Response syntax: +WVMI: <LineId>,<Num>
Command
Possible Responses
+WVMI: 1,2
OK
Note: 2 messages are in your voicemail box.
SMS Message Storage Full +WMGF
Description: This response indicates that the SMS Service Center has attempted to send an SMS
message but it was rejected because SMS Message Storage is Full. No new SMS
messages will be received until some room is created by deleting old messages from SMS
storage. Message deletion can be done using AT+CMGD.
Values:
<LineId>
1: Line 1
<Num>
The number of messages waiting in the inbox. Maximum value is 99.
0: No message waiting.
1: One message is waiting
3: Three messages are waiting
Example:
AT+CPHS?
+CPHS: 1,0
OK
Interrogate the status of CPHS functionality
The voice mail indicator functionality is deactivated
AT+CPHS=3,1
+CME ERROR:
AT+CPHS=1,1
OK
Syntax error
3
Activate the voice mail indicator functionality
AT+CPHS?
+CPHS: 1,1
OK
Interrogate the status of CPHS functionality
The voice mail indicator functionality is activated
**** the message box contains 1 message *****
+WVMI: 1,1
AT+CPHS=2,1
OK
A message is waiting on Line 1
Interrogate the status of voice mail indicator functionality
+WVMI: 1,1
AT+CPHS?
+CPHS: 1,1
OK
A message is waiting on LINE 1
Interrogate the status of CPHS functionality
The voice mail indicator functionality is activated
Syntax:
Response Syntax: +WMGF
Example Result
+WMGF
Note: Incoming message rejected. Message center notified with “out of resources” message.
Message center will attempt to re-send the message at a later time.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 – Unsolicited AT Result Codes
Power Save +WSPS
Description: This response is output whenever a change occurs in the power save status. The +WSPS
command can also be used to exit power save mode.
Note: This response is not used in Verizon software versions.
Syntax:
Response Syntax: +WSPS: <state>
Command
Possible responses
+WSPS: 1
Note: Entering power save mode.
AT+WSPS
OK
+WSPS: 0
Note: Send command to leave power save mode.
AT+WSPS?
Note: Command accepted.
+WSPS: 0
OK
Note: Display current power mode state.
<state>
Note: Leaving power save mode.
0: Leaving power save
1: Entering power save
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 – General Commands
CHAPTER 4 - GENERAL COMMANDS
Request Revision Identification +CGMR
Description: This command is used to display the operating software version.
Syntax:
Command syntax: AT+CGMR
Command
Possible Responses
AT+CGMR
+CGMR: S/W VER: WISMOQ WQ1.1 Mar 20 2002 17:30:00
OK
Note: Get software version
Note: Software Version WISMOQ, revision WQ1.1 generated
on the March 20th, 2002 at 17:30:00
Electronic Serial Number +CGSN
Description: This command allows the user application to get the ESN of the product. The ESN value is
displayed in hexadecimal format.
Syntax:
Command syntax: AT+CGSN
Command
AT+CGSN
Possible Responses
+CGSN: FE7A7704
OK
Note: Get the ESN
Note: ESN read from NV
Select TE Character Set +CSCS
Description: This command informs the MS which character set is in use by the TE. The MS uses this
information to convert each character of entered or displayed text data. The character set is
used for send, read or write of short messages.
Values:
Syntax:
<Character Set>
“CDMA” CDMA default (ASCII) character set.
“CUST” Custom character set.
Command syntax: AT+CSCS=<Character Set>
Command
Possible Responses
AT+CSCS=”CDMA”
Note: CDMA default alphabet
AT+CSCS?
OK
Note: Command valid
+CSCS: “CDMA”
OK
Note: Custom character set
Note: Command valid
+CSCS: ("CDMA","CUST")
OK
AT+CSCS=?
Note: Get possible values
Note: Possible values
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 – General Commands
Request IMSI +CIMI
Description: This command is used to read and identify the IMSI (International Mobile Subscriber
Identity) of the modem. The PIN may need to be entered using the CPIN command before
reading the IMSI.
Syntax:
Command syntax: AT+CIMI
Command
Possible Responses
AT+CIMI
Note: Read the IMSI
+CIMI: 310008585551212
OK
Note: IMSI value (15 digits)
Capabilities List +GCAP
Description: This command gets the complete list of capabilities.
Syntax:
Command syntax: AT+GCAP
Command
Possible Responses
AT+GCAP
Note: Get capabilities list
+GCAP: +CGSM, +CIS707-A, +MS, +ES, +DS, +FCLASS
OK
Repeat Last Command A/
Description: This command repeats the previous command. Only the A/ command itself cannot be
repeated.
Syntax:
Command syntax: A/
Command
Possible Responses
A/
Note: Repeat last command
Phone Offline +CPOF
Description: This command sends all CDMA software stack tasks offline. AT command can still be
received, however, there is no RF functionality. The AT+CFUN=0 command is equivalent to
+CPOF.
Syntax:
Command syntax: AT+CPOF
Command
Possible Responses
AT+CPOF
+CPOF:
Note: Stop CDMA stack
OK
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 – General Commands
Set Phone Functionality +CFUN
Description: This command selects the mobile station’s level of functionality. AT+CFUN=0 is equivalent
to AT+CPOF
The AT+CFUN=1 (by default, AT+CFUN will act the same as AT+CFUN=1) command
restarts the entire CDMA stack and CDMA functionality: a complete software reset is
performed. In addition, the OK response will be sent at the last baud rate defined by the
+IPR command.
Values:
Syntax:
<functionality level>
0: Set the phone to OFFLINE mode.
1: Set the phone to ONLINE mode and resets the stet.
Command syntax: AT+CFUN=<functionality level>
Command
AT+CFUN?
Possible Responses
+CFUN: 1
Note: Ask for current functionality level
OK
Note: Full functionality
AT+CFUN=0
OK
Note: Set phone offline
AT+CFUN=1
Note: Command valid
OK
Note: Set phone ONLINE. A software reset is performed.
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 – General Commands
Phone Activity Status +CPAS
Description: This command returns the activity status of the mobile equipment.
Values
<pas>
0: ready (allow commands from TA/TE)
1: unavailable (does not allow commands)
2: unknown
3 ringing (ringer is active)
4: call in progress
5: asleep (low functionality)
6: corrupted RF calibration values (checksum mismatch)
Syntax:
Command syntax: AT+CPAS
Command
Possible Responses
AT+CPAS
Note: Current activity status
+CPAS: <pas>
OK
Report Mobile Equipment Errors +CMEE
Description: This command disables or enables the use of the “+CME ERROR : <xxx>” or “+CMS
ERROR :<xxx>” result code instead of simply “ERROR”. See chapter 20 (MS Error Result
Codes) for +CME ERROR result codes description and chapter 20 (Message Service Failure
Result Codesfor +CMS ERROR result codes.
Syntax:
Command syntax: AT+CMEE=<error reporting flag>
Command
AT+CMEE=0
Possible Responses
OK
Note: Disable MS error reports, use only « ERROR »
AT+CMEE=1
OK
Note: Enable «+CME ERROR: <xxx>» or «+CMS ERROR: <xxx>»
Keypad Control +CKPD
Description: This command emulates the MS keypad by sending each keystroke as a character in a
<keys> string.
If emulation fails, a +CME ERROR: <err> is returned. If emulation succeeds, the result
depends on the CDMA sequence activated: <keys>: string of the following characters (0-
9,*,#).
Syntax:
Command syntax: AT+CKPD=<keys>
Command
AT+CKPD=”*#21#”
Possible Responses
OK
Note: Key sequence allowed
AT+CKPD=1234
+CME ERROR 3
Note: Sequence not allowed
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 – General Commands
Clock Management +CCLK
Description: This command is used to set or get the current date and time of the MS real-time clock.
String format for date/time is: “yy/MM/dd,hh:mm:ss”.
Valid years are 98 (for 1998) to 97 (for 2097). The seconds field is not mandatory.
Default date/time is “98/01/01,00:00:00” (January, 1998 / midnight).
Syntax:
Command syntax: AT+CCLK=<date and time string>
Command
Possible Responses
AT+CCLK=”00/06/09,17:33:00”
Note: set date to June , 2000,
and time to 5:33pm
OK or ERROR
Note: Date/Time stored – ERROR returned when RTC
not enabled
AT+CCLK=”00/13/13,12:00:00”
Note: Incorrect month entered
AT+CCLK?
+CME ERROR 3
+CCLK: “00/06/09,17:34:23”
Note: Get current date and time
Note: current date is June 9, 2000 current time is 5:34:23
pm – network time if available, otherwise calculated
based on previous network time if available, otherwise
ERROR.
Ring Melody Playback +CRMP
Description: This command causes a melody to be played. The specified melody will playback in an
endless loop until stopped with another +CRMP command. All melodies are manufacturer
defined. Up to ten manufacturer-defined melodies can be available for individual playback.
Note: Looped melodies must be stopped by a +CRMP command with the <index> field set
to 0 (example: +CRMP=0,,,0).
When the +CRMP command is performed, the <volume> parameter overwrites the <sound
level> value of the +CRSL command.
Values:
<call type>
0:
Incoming voice call
1:
Incoming data call
2:
Incoming fax call
3:
Incoming short message (SMS)
<volume>
0:
1:
4:
Min volume (mute)
Default volume
Max volume
<type>
0:
Manufacturer Defined (default)
<index>
0:
Stop Melody Playback
1-10
Melody ID for voice/data/fax call type (default:1)
Syntax:
Command syntax: AT+CRMP=<call type>[,<volume>,<type>,<index>]
Command
Possible Responses
AT+CRMP=0,2,0,2 Note: Play voice call
melody index 2 with volume level 2.
AT+CRMP=0,,,0
OK Note: Melody Playback.
OK
Note: Stop the melody.
AT+CRMP=?
Note: supported parameters
Note: The melody is stopped.
+CRMP: (0-3),(0-4),(0-0),(0-10)
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 – General Commands
Ringer Sound Level +CRSL
Description: This command is used to set/get the sound level of the ringer on incoming calls.
Values:
<sound level>
0: Min volume (muted)
1: Default volume
4: Max volume
Syntax:
Command syntax: AT+CRSL=<sound Level>
Command
Possible Responses
AT+CRSL=0
OK
Note: Set volume to Min (muted).
Note: Current ring playing is muted.
AT+CRSL=4
OK
Note: Set volume to Max.
AT+CRSL?
Note: Current ring playing with Max. volume.
CRSL:4
OK
Note: Get current ringer sound level
AT+CRSL=4
Note: Supported parameters
Note: Current level is 4
CRSL: (0-4)
OK
Subscriber Number +CNUM
Description: This command is used to return the subscriber MSISDN. If the subscriber has different
MSISDNs for different services, each MSISDN is returned on a separate line.
Values:
<alphax>
<numberx>
<typex>
optional alphanumeric string associated with <numberx>
string type phone number with format as specified by <typex>
type of address byte in integer format – only supports 129
Syntax:
Command syntax: AT+CNUM
Response syntax: +CNUM: <alpha1>, <number1>, <type1>, <CR><LF>+CNUM: <alpha2>,
<number2>, <type2> …
Command
Possible Responses
AT+CNUM
Note: Get MSISDN
+CNUM :“Phone”,”8585551212”,129
Note: MSISDNs
AT+CNUM=?
+CNUM:
OK
Select Type of Address +CSTA
Description:
This command is used to select the type of phone address to use.
Values:
<typex> type of address byte in integer format – only supports 129
Syntax:
Command syntax: AT+CSTA=<typex>
Command
AT+CSTA?
Possible Responses
+CSTA: 129
Note: Get type of address
AT+CSTA=?
Note: Get supported address types
Note: Local Number format
+CSTA: (129-129)
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 – General Commands
View Modem Timers +WTMR
Description: This command is used to read the modem’s accumulated internal timers. These timers
include Uptime, Call Time, Call Count, and Last Call Time. Uptime is the number of seconds
the modem has been running since boot-up. Call Time is the total number of seconds the
modem has been in a call since manufacture (Voice, Data, Fax, OTASP, and CDMA Test
Calls; but SMS is not included). Call count is the total number of calls made since
manufacture. Last Call Time returns the time of the most recent call in seconds. It is not
stored in NV and is initialized to zero on boot-up. The range of all returned timer items is 0 to
4294967295 (136 years).
Values:
<Uptime>
seconds since modem boot-up
<Call Time>
<Call Count>
total call seconds since modem manufacture (excluding SMS)
total calls made since modem manufacture
<Last Call Time> time of the most recent call in seconds
Syntax:
Command syntax: AT+WTMR
Response syntax: +WTMR: <Uptime>,<Call Time>, <Call Count>, <Last Call Time>
Command
Possible Responses
AT+WTMR
Note: Display modem timers
+WTMR: 1029, 45670,289, 85
OK
Note: Uptime = 1029 seconds
Call Time = 45670 seconds
Call Count = 289 calls
Last Call Time = 85 seconds
Modem Serial Number +WMSN
Description: This command allows the user application to get the serial number of the modem.
Values:
The serial number is fifteen digits in length and structured as follows. Each X represents a
digit of the serial number.
Modem Type Year Built Week Built Unit Number Bench Number Part Number
XX
X
XX
XXXXX
XX
XXX
Syntax:
Command syntax: AT+WMSN
Command
AT+WMSN
Possible Responses
+WMSN: 123456789012345
OK
Note: Get the modem SN
Note: SN read from NV memory
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
CHAPTER 5 - CALL CONTROL COMMANDS
Dial Command D
Description: The ATD command is used to originate a voice, data or fax call. The dial command also
controls supplementary services.
For a data or a fax call, the application sends the following ASCII string to the product:
ATD<nb> where <nb> is the destination phone number.
Note: ATD<nb> is followed by PPP negotiation.
For a voice call, the application sends the following ASCII string to the product:
ATD<nb>; where <nb> is the dialing string or destination phone number, followed a
semicolon “;”. The dialing string may only contain characters “0-9”,”#”,”*” only. Note that
some countries may have specific numbering rules for their CDMA handset numbering.
The response to the ATD command is one of the following:
Verbose Result Code Numeric Code (with
Description
ATV0 set)
OK
0
Command executed (voice)
CONNECT <speed>
10,11,12,13,14,15
If the call succeeds, for data calls only, <speed> takes
the value negotiated by the product.
BUSY
7
8
3
6
If the called party is already in communication,
If no hang up is detected after a fixed network time-out
Call setup failed or remote user release.
Voice call with missing “;”
NO ANSWER
NO CARRIER
NO DIALTONE
Direct Dial
Syntax:
Command syntax: ATD<nb>[;]
Command
Possible Responses
ATD18005551212;
OK
Note: Attempt a voice Note: Command executed
call.
+WORG:18005551212
Note: Voice call origination sent to Base Station with dial string “18005551212”.
+WCNT: 9
Note: Call Connected, CDMA traffic channel established with service option 9.
You can now hear audio of the calling party’s phone ringing. However, this event
does not means the other calling party has answered.
OK
Note: Command executed
+WORG:5551212
ATD5551212;
Note: Example of a
failed voice call
attempt.
Note: Voice call origination sent to Base Station with dialing string “5551212”.
+WEND: 3
Note: Call Attempt failed/ended. Reason 3, signal faded.
Dialing from a phonebook entry (stored in the RUIM card or NV) can be performed with the
following commands:
ATD><index>; Call <index> from the +CPBS selected phonebook.
ATD>”Bill”; Call “Bill” from the +CPBS selected phonebook.
ATD><mem><index>; <mem> is a +CPBS=? listed phonebook and <index> is a valid l
location within the phonebook
Note: A semicolon must be used at the end of the AT command to signal phonebook dialing.
Otherwise, the command will result in an error.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
Phonebook
Syntax:
Command syntax: ATD><index>[;]
ATD>[<mem>]<name>[;]
ATD>[<mem>]<index>[;]
Command
Possible Responses
+CPBS: ME,11,100
OK
AT+CPBS?
Note: Which phonebook is selected.
Note: Command executed
ATD>5;
OK
Note: Dial location #5 from ME
phonebook.
Note: Command executed
+WORG:5551212
Note: Voice call origination sent to Base Station with dialing
string “5551212”.
+WEND: 3
Note: Call Attempt failed/ended. Reason 3, signal faded.
See Chapter 14, Unsolicited Commands.
ATD>SM202;
OK
Note: Dial location 202 from the
SM(RUIM card) phonebook.
Note: Command executed
+WORG:5551212
Note: Voice call origination sent to Base Station with dialing
string “5551212”.
+WEND: 3
Note: Call Attempt failed/ended. Reason 3, signal faded.
See Chapter 14 on Unsolicited commands.
OK
ATD>”Bill”;
Note: This command is NOT valid for
MC, RC, and LD phonebooks as they
are supported in CDMA networks
Note: Command executed
+WORG:5551212
Note: When the FD facility is enabled, only the numbers in the FDN phonebook can be
called. For example, if “014629” is present in the FD phonebook, the command ATD014629;
will be successful. Data calls are not allowed when the FD facility is enabled.
Hang-Up Command H
Description: The ATH (or ATH0) command is used by the application to disconnect the remote user. In
the case of multiple calls, all calls are released (active, on-hold and waiting calls).
The specific ATH1 command has been appended to disconnect the current outgoing call,
only in dialing or alerting state (i.e. ATH1 can be used only after the ATD command, and
before its terminal response (OK, NO CARRIER, ...). It can be useful in the case of multiple
calls.
Syntax:
Command syntax: ATH
Command
Possible Responses
ATH
OK
Note: Ask for disconnection
+WEND: 10
Note: Every call, if any, is released
ATH1
ERROR
Note: Ask for outgoing call
disconnection
+WEND: 10
Note: Outgoing call, if any, is released
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
Answer a Call A
Description: When the product receives a call, it sets the RingInd signal and sends the ASCII “RING” or
“+CRING: <type>” string to the application (+CRING if the cellular result code +CRC is
enabled). Then it waits for the application to accept the call with the ATA command.
Syntax:
Command syntax: ATA
Command
Possible Responses
RING
Note: Incoming call
ATA
+WANS:0
Note: Answer to this incoming call
+WCNT: 10
Note: Call accepted
ATH
OK
Note: Disconnect call
+WEND: 10
Note: Call disconnected
Remote Disconnection
Description: A message is used by the product to inform the application that the remote user has
released an active call. The product sends +WEND: <result code> to the application. The
DCD signal may be set based upon the AT&C2 setting for packet calls. See chapter
3,Unsolicited Results for more information on the +WEND command.
Extended Error Report +CEER
Description: This command gives the cause of any general call processing error or malfunction. See
Chapter 20, Extended Error Report.
Syntax:
Command syntax: AT+CEER
Command
ATD18005551212;
Possible Responses
OK
+WORG:18005551212
+WCNT:3
ATD1234567;
ERROR
Note: Outgoing voice call while already in a call
Note: Call setup failure
AT+CEER
+CEER: Error 2
OK
Note: Operation not allowed when call in progress
AT+CEER
+CEER : Error <x>
OK
Note: Ask for reason of release
Note: <x>is the cause information element values
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
DTMF Signals +VTD, +VTS
+VTD
Description: The product enables the user application to send DTMF tones over the CDMA network. This
command is used to define tone duration (the default value is 0,0). To define this duration,
the application uses: AT+VTD=<on>,<off>.
Values:
<on> on tone duration
0: 95 milliseconds
1: 150 milliseconds
2: 200 milliseconds
3: 250 milliseconds
4: 300 milliseconds
5: 350 milliseconds
<off> off tone duration
0: 60 milliseconds
1: 100 milliseconds
2: 150 milliseconds
q3: 200 milliseconds
+VTD Syntax: Command syntax: AT+VTD=<on>,<off>
Command
AT+VTD=4,3
Possible Responses
OK
Note: To define 300 ms on tone duration and 200 ms off tone duration.
AT+VTD=?
Note: Display valid parameter ranges.
Note: Command valid
+VTD: (0-5), (0-3)
OK
+VTS
Description: The product supports the ability of the user application to send burst DTMF tones over the
CDMA network. This command enables the transmission of burst DTMF tones. To transmit
DTMF tones (only when there is an active call), the application uses: AT+VTS=<Tone>
where <Tone> is in {0-9,*,#}.
+VTS Syntax: Command syntax: AT+VTS=<Tone>
Command
Possible Responses
AT+VTS=#
OK
Note: Command valid
AT+VTS=11
AT+VTS=4
OK
OK
Informative Example: To send tone sequence 13#, the application sends: AT+VTS=13#
DTMF START and STOP Continuous +WSDT, +WSDS
Description: Starts and stops a continuous DTMF tone while in a call state (conversation).
Values:
Syntax:
<X>: (0-9, #,*)
Command syntax: AT+WSDT=<X>
Command
AT+WSDT=2
Possible Responses
OK
Starts DTMF tone
AT+WSDS
OK
Stops DTMF tone
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
Redial Last Telephone Number DL
Description: This command is used by the application to redial the last number used in an ATD
commanded voice call. The ATDL command causes the last voice call number to be
redialed. The phonebook is not referenced for the redial. Data call numbers are not
supported by this command; only voice call numbers.
Syntax:
Command syntax: ATDL
Command
Possible Responses
ATDL
OK
Note: Redial last number
+WORG: 8585551212
Note: Last call was a voice call. Command valid
Automatic Dialing with DTR %Dn
Description: This command enables and disables the automatic sending of the short message (SMS)
stored in the first location. The number is dialed and then short message is sent when DTR
OFF switches ON.
Values:
<n>
(0-2) Enable or disable automatic message transmission or number dialing.
Informs the product that the number is a voice rather than a fax or data number.
Disables automatic DTR number dialing / message transmission.
Currently not implemented.
Activates automatic DTR message transmission if DTR switches from OFF to
ON.
AT%D0
AT%D1
AT%D2
Syntax:
Command syntax: AT%D<n>
Command
Possible Responses
AT%D2
OK
Note: Activates DTR short message sending
Note: Command has been executed
Automatic Answer S0
Description: This S0 (zero) register parameter determines and controls the product automatic answering
mode.
Values:
Syntax:
<value>
(0-255)
No automatic answer.
Answers after the specified number of rings.
0:
1 – 255:
Command syntax: ATS0=<value>
Command
ATS0=2
Possible Responses
OK
Note: Automatic answer after 2 rings
ATS0?
002
OK
Note: Current value
ATS0=0
Note: always 3 characters padded with zeros
OK
Note: No automatic answer
Note: Command valid
Other S-parameter registers are implemented. See Chapter 17, Basic S-Registers.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
Incoming Call Bearer +CICB
Description: This specific command is used to set the type of incoming calls when no incoming bearer is
given (see +CSNS). The setting the +CICB command affects the current value of +CSNS.
Values:
<mode>
0: Data
1: Fax
2: Speech
3: Data once (10 minute timeout)
4: Fax once (10 minute timeout)
Syntax:
Command syntax: AT+CICB=<mode>
Command
Possible Responses
AT+CICB=1
OK
Note: If no incoming bearer,
force a fax call
Note: Command accepted
AT+CICB=2
OK
Note: If no incoming bearer,
force a voice call
AT+CICB?
Note: Command accepted
+CICB: 2
Note: Interrogate value
OK
Note: Default incoming bearer: voice call
AT+CICB=?
+CICB: (0-4)
Note: Test command
OK
Note: Speech, data or fax default incoming bearer
Single Numbering Scheme +CSNS
Description: This command selects the bearer to be used when an MT single numbering scheme call is
set up (see +CICB, these commands are the same).
Note: The setting the +CSNS command affects the current value of +CICB.
Values:
Syntax:
<mode>
0: Data
1: Fax
2: Speech
3: Data once (10 minute timeout)
4: Fax once (10 minute timeout)
Command syntax: AT+CSNS
Command
Possible Responses
AT+CSNS=0
OK
Note: Force a data call
Note: Command accepted
AT+CSNS=2
OK
Note: Force a voice call
AT+CSNS?
Note: Command accepted
+CSNS: 2
Note: Interrogate value
OK
Note: Default incoming bearer: voice call
AT+CSNS=?
+CSNS: (0-4)
Note: Test command
OK
Note: Voice, data or fax default incoming bearer
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
Microphone Gain +VGT
Description: This command sets the microphone gain of the current audio path.
Values:
<MicGain> value to Microphone relative gain:
AT+VGT Value
Microphone Relative Gain Step (dB)
0
1
2
3
-2
+6
+8
+16
Syntax:
Command syntax: AT+VGT=<MicGain>
Command
Possible Responses
AT+VGT=2
OK
Note: Command valid
AT+VGT?
+VGT: 2
Note: Interrogate value
OK
Note: Current value
+VGT : (0-3)
OK
AT+VGT=?
Note: Test command
Note: Possible values
Volume Gain Control +VGR
Description: This command is used by the application to tune the receive gain of the speaker. If the
modem is in the Idle state, it will generate an audible tone at the selected volume.
Values:
<RGain> value to Speaker relative gain:
AT+VGR Value
Speaker Relative Gain Step (dB)
0
1
2
3
4
Mute
-23
-17
-11
-5
Syntax:
Command syntax: AT+VGR=<Rgain>
Command
Possible Responses
AT+VGR=2
OK
Note: Command valid
AT+VGR?
+VGR: 2
Note: Interrogate value
OK
Note: Current value
AT+VGR=?
+VGR : (0-4)
Note: Test command
OK
Note: Possible values; default: 3
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
Microphone Mute Control +CMUT
Description: This command is used to mute the microphone input on the product (for the active
microphone set with the +SPEAKER command). This command is only allowed during a call.
Values:
Syntax:
<mode>
0: Microphone mute off (default value).
1: Microphone mute on.
Command syntax: AT+CMUT=<mode>
Command
AT+CMUT=?
Possible Responses
+CMUT : (0-1)
OK
Note: Test command
AT+CMUT?
Note: Enable / disable mute
+CMUT : 0
OK
Note: Ask for current value
AT+CMUT=1
Note: Current value is OFF
OK
Note: Mute ON (call active)
AT+CMUT?
Note: Command valid
+CMUT : 1
OK
Note: Ask for current value
AT+CMUT=0
Note: Mute OFF (call not active)
Note: Mute is active (call active)
+CME ERROR: 3
Note: Command not valid
Speaker & Microphone Selection +SPEAKER
Description: This command is used to select the speaker and the microphone set.
Values:
<ActiveSpkMic >
0: HEADSET
1: HANDSET
Syntax:
Command syntax: AT+SPEAKER=<ActiveSpkMic>
Command
Possible Responses
AT+SPEAKER=1
OK
Note: Speaker ONE and Micro ONE
Note: Command valid
AT+SPEAKER?
+SPEAKER: 1
OK
Note: Speaker ONE and Micro ONE are active.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
Echo Cancellation +ECHO
Description: This command is used to enable, disable or configure the Echo Cancellation functions for
voice calls (in rooms, in cars, etc.). The +SPEAKER function automatically sets echo
cancellation based upon handset or headset choice and this command allows non-standard
operation.
Values:
<mode>
0: Vocoder Echo Cancellation Off
1: Ear Seal Echo Cancellation
2: Head Set Echo Cancellation
3: AEC
4: Speaker Echo Cancellation for car kit operation
5: Default Echo Cancellation for current path settings
Syntax:
Command syntax: AT+ECHO= <mode>
Command
Possible Responses
AT+ECHO?
Note: Read current settings
+ECHO: 0
OK
AT+ECHO=0
OK
Note: Set Echo Cancellation Off
AT+ECHO=1
OK
Note: Set Echo Cancellation to Ear Seal
AT+ECHO=2
Note: Set Echo Cancellation to Headset
OK
OK
AT+ECHO=4
Note: Set Echo Cancellation to Handset
Side Tone Modification +SIDET
Description: This command is used to set the level of audio feedback in the speaker (microphone
feedback in the speaker).
Values:
<val1>
0: Sidetone is disabled
1: Sidetone is enabled
<val2>
0: No side tone
1: Handset Sidetone levels
2: Headset Sidetone levels
3: Max Sidetone level
Syntax:
Command syntax: AT+SIDET=<val1>,<val2>
Command
Possible Responses
AT+SIDET=1,0
OK
Note: Command valid
AT+SIDET?
Note: Current value
+SIDET: 1,0
OK
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 – Call Control Commands
Initialize Voice Parameters +VIP
Description: This command allows voice parameters to be restored from NV memory.
Values:
Gain controls are restored (+VGT and +VGR)
Voice path selection is restored (+SPEAKER)
Echo cancellation is restored (+ECHO)
Sidetone values are restored (+SIDET)
Syntax:
Command syntax: AT+VIP
Command
Possible Responses
AT+VIP
OK
Note: Command valid
TTY Mode +WTTY
Description: This command enables TTY mode on the headset audio path. The modem must be in a
voice call to set this command, and when the call ends it goes back to standard audio mode.
Syntax:
Command syntax: AT+WTTY
Command
Possible Responses
AT+WTTY
OK
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 – Network Service Commands
CHAPTER 6 - NETWORK SERVICE COMMANDS
Signal Quality +CSQ
Description: This command is used to ascertain the received signal strength indication (<rssi>) and the
channel frame error rate (<fer>). The exact meaning of the SQM (RSSI) value is
manufacturer defined.
Note: See Chapter 24 for Sprint® specific version of this command.
Values:
Syntax:
<rssi>:
0-31: Valid value ranges.
255: Represents an unknown signal quality.
<fer>:
99: Not known or not detectable. Currently always returns 99.
Command syntax: AT+CSQ
Command
AT+CSQ
Possible Responses
+CSQ: <rssi>,<fer>
OK
Note: <rssi> and <fer> as defined below
Mode Preference +COPS
Description: The Mode Preference of a CDMA modem governs the basic system acquisition behavior of
the MS in conjunction with the PRL (Preferring Roaming List). It’s important to note that the
PRL takes precedence over mode preference when guiding the phone to a band or system.
The PRL must allow a particular band first, before the mode preference can take effect. In
other words, a mode preference change is simply a request; the PRL decides whether or not
to allow it. After execution of the +COPS command, an unsolicited +COPS: <mode> will
follow soon to confirm the new mode selection, but not in all cases. See Unsolicited Result
Codes in Chapter 3. All changes to +COPS are automatically saved in NV RAM.
Note 1: AMPS selection is available only in modems that support AMPS mode.
Note 2: Refer to Chapter 20 for AT commands that are applicable to AMPS operation.
Note 3: This command is not available in Sprint®. and Verizon. software versions.
Note 4: CDMA Only (<mode> 1) is the only available mode in RUIM software versions. An
attempt to select any other mode in RUIM software versions will result in an error return.
Values:
The parameter values are the following ones:
<mode>
0: Automatic.
1: CDMA Only.
2: CDMA or AMPS only.
3: Analog only.
<term>
0: Permanent – this mode persists until another +COPS command is issued
1: Power cycle – this mode persists until power cycle is performed
Note:
1: AT+COPS by itself is a short-hand equivalent to AT+COPS=0,0.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 – Network Service Commands
Syntax:
Command syntax: AT+COPS=<mode>,<term>
Command
Possible Responses
AT+COPS?
Note: Ask for current Mode Preference
+COPS: 0,0
OK
Note: Automatic mode, use PRL order, Permanent
AT+COPS=?
+COPS: (0-3),(0-1)
OK
Note: Modes: Automatic, CDMA Only, CDMA or AMPS
only; Term: Permanent, Power Cycle.
AT+COPS=0,0
OK
Note: Ask for Automatic mode
+COPS: 0,0
Note: Unsolicited +COPS result confirms Automatic
mode, Permanent term is requested.
AT+COPS=1,1
OK
Note: Ask for CDMA Only mode
+COPS: 1,1
Note: Unsolicited +COPS result confirms CDMA Only
mode, Power Cycle term is requested.
AT+COPS=2,0
OK
Note: Ask for CDMA or AMPS only mode +COPS: 2,0
Note: Unsolicited +COPS result confirms CDMA or
AMPS only mode, Permanent term is requested.
AT+COPS=3,0
OK
Note: Ask for Analog only mode
+COPS: 3,0
Note: Unsolicited +COPS result confirms Analog only
mode, Permanent term is requested.
Band Preference +WBND
Description: The Band Preference of a CDMA modem governs the basic system acquisition behavior of
the MS in conjunction with the mode preference (+COPS) and the PRL (Preferring Roaming
List). It’s important to note that the PRL takes precedence over band preference when
guiding the phone to a band. The PRL must allow a particular band first, before the band
preference can take effect. In other words, a band preference change is simply a request;
the PRL decides whether or not to allow it. If the setting is accepted by the MS, the value will
be written to non-volatile RAM and persist after a power-cycle.
Note 1: This command is not available in Sprint®. and Verizon. software versions.
Note 2: <band> 1 (PCS) is not available in RUIM software versions.
Values:
The parameter values are the following ones:
<band>
0: Any
1: PCS
2: Cellular A or B
3: Cellular A
4: Cellular B
Syntax:
Command syntax: AT+WBND=<band>
Command
Possible Responses
AT+WBND?
+WBND: 0
Note: Ask for current Band Preference
OK
Note: Any
AT+WBND=?
+WBND: (0-4)
OK
Note: Any, PCS, Cell, Cell A, Cell B
AT+WBND=0
OK
Note: Allow Any Band
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 – Network Service Commands
Roam Preference +WRMP
Description: The Roam Preference of a CDMA modem informs the MS whether it is allowed to roam on
foreign CDMA networks or only allow operation on home networks. The determination of
what is a foreign or home network is programmed into the PRL (Preferring Roaming List).
This command simply enables or disables the capability of the MS to roam, based on the
PRL configuration. If the setting is accepted by the MS, the value will be written to non-
volatile RAM and persist after a power-cycle. After execution of the +WRMP command, the
MS may change roaming states. The unsolicited result +WROM: <mode> will indicate the
new state. See Unsolicited Result Codes in Chapter 3.
Note: This command is not available in Sprint®. and Verizon. software versions.
Values:
Syntax:
The parameter values are the following ones:
<mode>
0: Home Networks only, as defined in the PRL (default value)
1: Roaming on Affiliated networks, as defined in the PRL
2: Roaming on Any Network, as defined in the PRL.
Command syntax: AT+WRMP=<mode>
Command
AT+WRMP?
Possible Responses
+WRMP: 0
Note: Ask for current Mode
Preference
OK
Note: Home only
AT+WRMP=?
+WRMP: (0-2)
OK
Note: Home, Affiliated, Any
AT+WRMP=0
OK
Note: Allow Home only networks
+WROM: 0
Note: Unsolicited +WROM may or may not appear
based on current circumstances
AT+WRMP=1
OK
Note: Allow Roaming Affiliated
Networks
+WROM: 1
Note: Unsolicited +WROM may or may not appear
based on current circumstances
OK
AT+WRMP=2
Note: Allow Roaming on Any
Network
+WRMP: 2
Note: Unsolicited +WROM may or may not appear
based on current circumstances
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 – Network Service Commands
Network Registration & Roaming +CREG
Description: This command is used by the application to ascertain the registration and roaming status of
the product.
Note: Also see +WROM unsolicited command for CDMA roaming status.
Values:
<mode>
0: Disable network registration unsolicited result code (default)
1: Enable network registration unsolicited code result code +CREG: <stat>
<stat>
0: not registered, MS is not currently searching for a new operator.
1: registered, home network.
2: not registered, MS currently searching for a base station.
4: unknown.
5: registered, roaming
Syntax:
Command syntax: AT+CREG= <mode>
Response syntax: +CREG: <mode>, <stat>
Command
AT+CREG=0
Possible Responses
+CREG: 0,1
Note: Disable network registration unsolicited result
code.
OK
Note: Command valid
AT+CREG=1
Note: Enable network registration unsolicited result
code
+CREG: 1,1
OK
Note: Command valid
AT+CREG?
+CREG: 1,5
OK
Note: Unsolicited enabled, MS currently roaming.
AT+CREG=?
+CREG: (0-1)
OK
Note: 0,1 <mode> values are supported
Note: Example of the unsolicited result code. MS is
searching for a base station.
+CREG: 2
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 – Network Service Commands
Change NAM Selection +WNAM
Description: This command is used to request a change in the NAM (Number Assignment Modem)
selection. The modem supports up to 4 NAMs. However, if a NAM is not fully programmed,
the modem will not switch to the requested NAM. The default NAM for the modem is 1. The
response to this command is only OK, and is no guarantee that the NAM will change. If the
NAM selection request is accepted, the unsolicited command +WNAM: <nam> will be
returned. If or when the actual NAM changes, the unsolicited command +WCNM: <nam> will
be returned. See Unsolicited Result Codes in Chapter 3.
Values:
<nam>
1: NAM 1
2: NAM 2
3: NAM 3
4: NAM 4
5: Auto NAM
Syntax:
Command syntax: AT+WNAM=<nam>
Command
Possible Responses
AT+WNAM=2
Note: Use NAM 2, if
programmed
OK
+WNAM: 2
+WCNM: 2
AT+WNAM=3
OK
Note: Use NAM 3, if
programmed
Note: No unsolicited response indicates that
NAM 3 is not valid, thus no change in NAM.
AT+WNAM=5
OK
Note: Try Auto NAM
+WNAM: 5
+WCNM: 1
Note: Auto NAM is selected, NAM 1 chosen.
AT+WNAM?
+WNAM: 1
AT+WNAM=?
+WNAM: (1-5)
Read Current NAM +WCNM
Description: This command is used to read the current NAM (Number Assignment Modem). The modem
supports up to 4 NAMs. Also, note that there exists an unsolicited command +WCNM:
<nam> that is returned any time the NAM changes. See Unsolicited Result Codes in
Chapter 3.
Syntax:
Command syntax: AT+WCNM
Command
Possible Responses
AT+WCNM
Note: Ask for the current NAM
+WCNM: 1
OK
Note: NAM 1 in use
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 – Network Service Commands
Emergency Mode +WSOS
Description: In the event of an emergency call, the modem will automatically put itself into emergency
mode. After the call has ended and/or emergency mode is no longer desired, this command
must be sent to exit the modem out of emergency mode.
Note: Changing the mode preference using +COPS while emergency mode is in effect will
exit the modem out of Emergency Mode.
Note: For RUIM capable modems, the emergency numbers 110, 112, 119, and 120 are also
supported by the modem software in addition to 911.
Values:
Syntax:
The parameters values are the following ones:
<flag>
0: Exit Emergency Mode
1: Manually enter Emergency Mode (not supported)
Note: 1: AT+WSOS by itself is a short-hand equivalent to AT+WSOS=0.
Command syntax: AT+WSOS=<flag>
Command
Possible Responses
AT+WSOS?
+WSOS: 1
Note: Ask for current Emergency Mode status
OK
AT+WSOS=?
+WSOS: (0-0)
OK
AT+WSOS
OK
Note: Exit Emergency Mode.
Note2: This is the same as AT+WSOS=0
+WSOS:0
Note: Unsolicited +WSOS result confirms Emergency
Mode exit
AT+WSOS=0
OK
Note: Exit Emergency Mode.
+WSOS:0
Note: Unsolicited +WSOS result confirms Emergency
Mode exit
AT+WSOS=1
ERROR
Note: Try to manually enter Emergency Mode.
This is not allowed.
ATD911;
Note: This is not allowed. Emergency Mode will only be
entered as a result of an emergency call
+WSOS: 1
Note: Emergency Mode entered as the result
of an emergency call
+WORG: 911
AT+COPS=0,0
+WSOS: 0
Note: Changing the mode preference while in
Emergency Mode, will result in Emergency
Mode being exited
+COPS: 0,0
Note: An unsolicited response for both +WSOS and
+COPS are returned when mode preference is changed
while in Emergency Mode.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 – Network Service Commands
Extended Roam Indication +WRMW
Description: This command is used to suppress output of non-standard Extended Roam Indicators (64
through 127) that are displayed by the +WROM unsolicited response. This setting is written
to NV and is persistent across resets.
Note: This command is not available in Sprint®. and Verizon®. software versions.
Values:
Syntax:
<value>
0: Suppress output of ERI indicators 64 through 127.
1: Enable output of ERI indicators 64 through 127.
Command syntax: AT+WRMW=<value>
Command
Possible Responses
AT+WRMW=?
+WRMW: (0-1)
OK
AT+WRMW?
+WRMW: 0
Note: Display current setting.
OK
Note: ERI 64 through 127 suppressed.
AT+WRMW=1
OK
Note: Enable output of ERI 64 through 127.
AT+WRMW?
+WRMW: 1
Note: Display current setting.
OK
Note: ERI 64 through 127 displayed.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - SIM Card Operational Commands
CHAPTER 7 - SIM CARD OPERATIONAL COMMANDS
This section details the commands that are available when a SIM card is present. These commands are
available only in RUIM software versions.
Note that the PIN codes used in this section are for example purposes only and do not reflect the actual PIN
codes programmed into the modem. Contact your service provider to obtain the actual PIN codes used by
your modem.
Enter PIN +CPIN
Description: This command is used to enter the ME (Mobile Equipment) passwords (CHV1 / CHV2 /
PUK1 / PUK2, etc.), that are required before any ME functionality can be used. CHV1/CHV2
must be 4 to 8 digits long, PUK1/PUK2 must be 8 digits long. The application is responsible
for checking the PIN after each reset or power on if the PIN was enabled.
Syntax:
Command syntax: AT+CPIN=<pin>
Command
Possible Responses
AT+CPIN=1234
OK
Note: PIN code is correct
After 3 unsuccessful attempts to enter the PIN (Personal Identification Number), the PUK
(Personal Unblocking Key) will be required. PUK validation forces the user to enter a new
PIN code as a second parameter and this will be the new PIN code if PUK validation
succeeds. CHV1 is then enabled if PUK1 is correct. The application therefore uses this
command:
Command syntax: AT+CPIN=<Puk>,<NewPin>
Command
AT+CPIN=00000000,1234
Note: Enter PUK and new PIN
AT+CPIN=12345678,1234
Note: Enter PUK and new PIN, 2nd attempt
Possible Responses
+CME ERROR: 16
Note: Incorrect PUK
OK
Note: PUK correct, new PIN stored
To ascertain which code must be entered (or not), the following query command can be
used: AT+CPIN?
The possible responses are:
+CPIN: READY
+CPIN: UIM PIN
ME is not pending for any password
CHV1 is required
+CPIN: UIM PUK
+CPIN: UIM PIN2
+CPIN: UIM PUK2
+CPIN: PH-UIM PIN
+CPIN: PH-NET PIN
+CME ERROR: <err>
PUK1 is required
CHV2 is required
PUK2 is required
UIM lock (phone-to-UIM) is required
Network personalization is required
SIM failure (13) absent (10) etc.
Note: that in this case the mobile equipment does not end its response with the OK string.
The response ‘+CME ERROR: 13’ (SIM failure) is returned after 10 unsuccessful PUK
attempts. The SIM card is then out of order and must be replaced by a new one.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - SIM Card Operational Commands
Enter PIN2 +CPIN2
Description: This command is used to validate the PIN2 code (CHV2), or to validate the PUK2 code
(UNBLOCK CHV2) and to define a new PIN2 code. Of course, the +CPIN command allows
PIN2 or PUK2 codes to be validated, but only when the last command executed resulted in
PIN2 authentication failure. PIN2 length is between 4 and 8 digits. The PUK2 length must be
8 digits.
Syntax:
Command syntax: AT+CPIN2=<pin2>
Command
Possible Responses
AT+CPIN2=1234
OK
Note: PIN2 code is correct
After 3 unsuccessful attempts, PUK2 will then be required. PUK2 validation forces the user
to enter a new PIN2 code as a second parameter and this will be the new PIN2 code if
PUK1 validation succeeds. The application therefore uses this command:
Command syntax: AT+CPIN2=<puk2>,<NewPin2>
Command
AT+CPIN2=00000000,1234
Note: Enter PUK2 and new PIN2
AT+CPIN2=12345678,1234
Note: Enter PUK2 and new PIN2, 2nd attempt
Possible Responses
+CME ERROR: 16
Note: Incorrect PUK2
OK
Note: PUK2 correct, new PIN2 stored
To ascertain which code must be entered (or not), the following query command can also be
used: AT+CPIN?
The possible responses are:
+CPIN: READY
ME is not pending for any password
CHV2 is required
PUK2 is required
+CPIN: UIM PIN2
+CPIN: UIM PUK2
+CME ERROR: <err>
SIM failure (13) absent (10) etc.
The product requires that the PIN2 code be successfully entered in order to write a entry into
the Fix Dialing Phonebook (FDN).
Command
Possible Responses
AT+CPBS=”FD”
OK
Note: Select Phonebook FDN
AT+CPBW=5,”12345678”,145”test1”
Note: Write entry 5 in the FDN
AT+CPIN2=1234
+CME ERROR: 17
Note: PIN2 not yet entered
OK
Note: Enter PIN2
Note: PIN2 successfully entered
AT+CPBW=5,”12345678”,145”test1”
Note: Write entry 5 in the FDN
OK
Note: Command now successful
PIN Remaining Attempt Number +CPINC
Description: This command is used to get the number of valid attempts for PIN1 (CHV1), PIN2 (CHV2),
PUK1 (UNBLOCK CHV1) and PUK2 (UNBLOCK CHV2) identifiers.
Values:
Syntax:
<n1>, <n2> are the attempts left for PIN1, PIN2 (0 = blocked, 3 max)
<k1>, <k2> are the attempts left for PUK1, PUK2 (0 = blocked, 10 max)
For this to work, the card should be present at the time of initialization. Otherwise, an error
will be sent (+CME ERROR: 10).
Command syntax: AT+CPINC
Response syntax: +CPINC: <n1>,<n2>,<k1>,<k2>
Command
Possible Responses
AT+CPINC
+CPINC: 2,3,10,10
Note: Get the number of attempts left
OK
Note: First CHV1 attempt was a failure
AT+CPINC?
+CPINC: 2,3,10,10
Note: Get the number of attempts left
OK
Note: First CHV1 attempt was a failure
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - SIM Card Operational Commands
Facility Lock +CLCK
Description: This command is used by the application to lock, unlock or interrogate an ME or network
facility <fac>. The call barring facilities “A0” and “AI” require that a password value be
included in the command even though passwords are not currently enforced for these
facilities. The “SC” and “FD” facilities are available only in builds, which include UIM support.
This command is also used for the control of the call barring supplementary service.
Functions for the barring of data and voice calls is provided as well as querying the status of
call barring. Note that emergency voice calls cannot be barred.
Values:
The following <fac> values are supported:
“SC”: SIM PIN enabled (<mode> = 1) / disabled (<mode> = 0)
“FD”: SIM FDN feature enabled (<mode> = 1) / disabled (<mode> = 0)
“AO”: BAOC; Barr Outgoing Calls
“AI”: BAIC; Barr Incoming Calls
<mode>
0: Unlock the facility (<passwd> required)
1: Lock the facility (<passwd> required)
2: Query status
<passwd>
Use PIN1 for the “SC” facility
Use PIN2 for the “FD” facility
Use any four digit value for the “AO” and “AI” facilities
Syntax: (for Facility Lock):
Command syntax: AT+CLCK= <fac>,<mode>[,<passwd>]
Response syntax: +CLCK: <status>
Command
Possible Responses
AT+CLCK=”SC”,1,1234
Note: Enable SIM PIN
AT+CLCK?
OK
Note: SIM PIN enabled
+CLCK:(“SC”,1),(“FD”,0),(“AO”,1),(“AI”,1)
Note: Get current facility lock status
OK
Note: SIM PIN is enabled, SIM FDN feature is disabled,
Outgoing call barring is enabled, Incoming call barring is
enabled
AT+CLCK=”SC”,0,5555
Note: Disable SIM PIN
AT+CLCK=”AO”,1,1234
Note: Bar Outgoing Calls
AT+CLCK=”AI”,1,1234
Note: Bar Incoming Calls
AT+CLCK=”AO”,2
+CME ERROR: 16
Note: Incorrect password used
OK
Note: Outgoing calls are barred
OK
Note: Incoming calls are barred
+CLCK: 1
Note: Query outgoing call barring status OK
Note: Outgoing calls are barred
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - SIM Card Operational Commands
Change Password +CPWD
Description: This command is used by the application to change a password, PIN1or PIN2. The “SC” and
“P2” facilities are available only in builds, which include stet support.
Values:
The following <fac> values are supported:
“SC”: PIN1
“P2”: 7.6.2 PIN2
<oldpwd>
Current PIN1 or PIN2 password
<newpwd>
Desired PIN1 or PIN2 password
Syntax:
Command syntax: AT+CPWD= <fac>, <oldpwd>, <newpwd>
Command
Possible Responses
AT+CPWD=”SC”,1234,5555
Note: Change stet PIN1
AT+CPWD=”SC”,1234,5555
Note: Change stet PIN1
AT+CPWD?
OK
Note: PIN1 now 5555
+CME ERROR: 16
Note: PIN incorrect
+CPWD:(“SC”,8),(“P2”,8)
Note: Get status
OK
Note: PIN1 & PIN2 passwords are supported with 8 digit maximum
Card Identification +CCID
Description: This command is used to display the SIM card ESN. The data is output in hexadecimal
format. If there is no ESN present on the SIM card, only the OK portion of the message will
be output.
Syntax:
Command syntax: AT+CCID
Command
Possible Responses
AT+CCID
+CCID: C3729F82
Note: Get card ID
Note: ESN is presented in hexadecimal format.
AT+CCID?
+CCID: C3729F82
Note: Get current value
AT+CCID=?
Note: Same result as +CCID
OK
Note: Get possible value
Note: No parameter but this command is valid.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
CHAPTER 8 - SHORT MESSAGES COMMANDS
For SMS messages, in the CDMA system, the PDU mode will not be supported, instead, the Unicode format
message is supported. The Unicode header code will start at 0x80 and above.
Parameters Definition
<cbn>
<da>
Call Back Number
Destination Address
<dcs>
<dt>
Data Coding Scheme, coded like in document [5].
Discharge Time in string format :
“yy/mm/dd,hh :mm :ss”(Year [00-99], Month [01-12],
Day [01-31], Hour, Minute, Second
<encod> Encoding
<fo>
First Octet, coded like SMS-SUBMIT first octet in document [4], default value is 17 for SMS-
SUBMIT
<index>
<lang>
Place of storage in memory.
Language
<length> Length of SMS User Data field.
<mem1> Memory used to list, read and delete messages (+CMGL, +CMGR and +CMGD).
<mem2> Memory used to write and send messages (+CMGW, +CMSS).
<mid>
<mr>
<oa>
CBM Message Identifier.
Message Reference.
Originator Address.
Protocol Identifier.
<pid>
<priority> Message Priority
<ra>
Recipient Address.
<sca>
<scts>
Service Center Address
Service Center Time Stamp in string format : “yy/mm/dd,hh :mm :ss”
(Year/Month/Day,Hour:Min:Seconds)
CBM Serial Number
<sn>
<st>
Status of a SMS-STATUS-REPORT (see Chapter 17for possible values)
Status of message in memory.
Type-of-Address of <oa>.
Type-of-Address of <ra>.
Type-of-Address of <sca>.
Number of message locations in <mem1>.
Number of messages locations in <mem2.
Timestamp for MT SMS.
<stat>
<tooa>
<tora>
<tosca>
<total1>
<total2>
<ts>
<used1> Total number of messages locations in <mem1>.
<used2> Total number of messages locations in <mem2.
<vp>
Validity Period of the short message, default value is 167
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Select Message Service +CSMS
Description: This command is used to display the supported SMS services. The supported services are
originated (SMS-MO) and terminated short message (SMS-MT) + Cell Broadcast Message
(SMS-CB) services.
Values:
<MO>
0: Mobile Originated SMS not supported.
1: Mobile Originated SMS supported.
<MT>
0: Mobile Terminated SMS not supported.
1: Mobile Terminated SMS supported.
<CB>
0: Broadcast SMS not supported.
1: Broadcast SMS supported.
Syntax:
Command syntax: AT+CSMS?
Command
Possible Responses
AT+CSMS?
+CSMS: <MO>,<MT>,<CB>
Note: Display current values
OK
Note: SMS-MO, SMS-MT and SMS-CB support
New Message Acknowledgement +CNMA
Description: This command allows reception of a new message routed directly to the TE to be
acknowledged.
In TEXT mode, only positive acknowledgement to the network (RP-ACK) is possible.
Acknowledge with +CNMA is possible only when a +CMT or +CDS indication is shown (see
+CNMI command).
Note: This AT command is not designed for input of the command into the Hyper terminal by
hand since the acknowledgement will not be quick enough to be received by the network.
However, it is possible for the client system to automatically send this command when the
+CNMI is set to “2,2,0,0,0”.
Syntax:
Command syntax: AT+CNMA
Command
Possible Responses
AT+CNMI=2,2,0,0,0
OK
+CMT:”8587351530”,”02/04/03,11 :06
:38”,129,7,0<CR><LF>
Testing
Note: Message received
AT+CNMA
OK
Note: Acknowledge the message received
Note: Send positive acknowledgement to the network
AT+CNMA
+CMS ERROR : 340
Note: Try to acknowledge again
Note: No +CNMA acknowledgment expected
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Preferred Message Storage +CPMS
Description: This command allows the message storage area to be selected (for reading, writing, etc).
The total storage area size is: 30 for “MT”, “MO”, “BC” and 10 for “SR”. For RUIM software
loads, these sizes vary and are dependent on the configuration of the SIM card.
Values:
<mem1>: Memory area to be used to list, read and delete messages. It can be:
“MT”: SMS Mobile Terminated message storage in NV (default)
“BC”: CBM message storage in NV.
“SR”: Status Report message storage in NV.
<mem2>: Memory used to write and send messages.
“MO”: Mobile Originated SMS message storage.
In response to a properly entered +CPMS command, the following message indication is
sent:
+CPMS: <used1>,<total>,<used2>,<total> where:
<used1> is the number of used locations for the select area “MT”, “BC”, or “SR” and
<used2> is the number of used locations for the “MO” area. <total> is the total number of
available storage locations (shared by all storage areas).
When <mem1> is selected, all following +CMGL, +CMGR and +CMGD commands are
related to the type of SMS stored in this memory.
Syntax:
Command syntax: AT+CPMS=<mem1>,[<mem2>]
Command
Possible Responses
AT+CPMS=?
+CPMS: (“MT”,”BC”,”SR”),(“MO”)
Note: Display available message
storage areas.
OK
Note: Read, list, delete: SMS, CBM or SMS Status Report. Write,
send: SMS
AT+CPMS?
Note: Display currently selected area
information.
+CPMS: “MT”,3,30,”MO”,3,30
OK
AT+CPMS=”AM”
+CMS ERROR: 302
Note: Select invalid message storage
area.
AT+CPMS=”BC”
+CPMS: 2,30,3,30
Note: Select CBM message storage
OK
Note: Read, list, delete CBM from NV RAM
Show Text Mode Parameters +CSDH
Description: This command gives additional information on text mode result codes. This information is
given in brackets in the +CMTI, +CMT, +CDS, +CMGR, +CMGL commands.
Syntax:
Command syntax: AT+CSDH
Command
Possible Responses
AT+CSDH?
+CSDH: 0
Note: Current value
OK
Note: Do not show header values
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
New Message Indication +CNMI
Description: This command selects the procedure for message reception from the network.
Values <mode>
The <mode> value controls the processing of unsolicited result codes. Only mode 2 is
supported at this time. The other mode values are accepted and return OK but the
processing of unsolicited result codes will be the same as with mode value 2.
0: Buffer unsolicited result codes in the TA. If the TA result code buffer is full,
indications can be buffered in some other place or the oldest indications may be
discarded and replaced with the new received indications
1: Discard indication and reject new received message unsolicited result codes when
TA-TE link is reserved. Otherwise forward them directly to the TE
2: Buffer unsolicited result codes in the TA when TA-TE link is reserved and flush them
to the TE after reservation. Otherwise forward them directly to the TE
3: Forward unsolicited result codes directly to the TE. TA-TE link specific in band used
to embed result codes and data when TA is in on-line data mode
<mt> sets the result code indication routing for SMS-DELIVERs. Default is 2.
0: No SMS-DELIVER indications are routed.
1: SMS-DELIVERs are routed using unsolicited code: +CMTI: “MT”, <index>
2: SMS-DELIVERs (except class 2 messages) are routed using unsolicited code:
+CMT: <oa>, <scts>, <tooa>, <lang>, <encod>,
<priority>[,<cbn>],<length><CR><LF><data> (text mode)
<bm> sets the result code indication routing for received Cell Broadcast Messages. Default
is 2.
0: No CBM indications are routed to the TE. The CBMs are stored.
1: The CBM is stored and an indication of the memory location is routed to the
customer application using unsolicited result code: +CBMI: “BC”, <index>
2: New CBMs are routed directly to the TE using unsolicited result code (format
matches that of +CBM: <oa>, [<alpha>,] <scts> [,<tooa>, <length>]
<CR><LF><data> (text mode)
<ds> sets the routing for SMS-STATUS-REPORTs. Default is 1.
0: No SMS-STATUS-REPORTs are routed.
1: SMS-STATUS-REPORTs are routed using unsolicited code: +CDS: <fo>, <mr>,
[<ra>] , [<tora>], <scts>, <dt>, <st> (Text mode)
2: SMS-STATUS-REPORTs are stored and routed using the unsolicited result ode:
+CDSI: “SR”, <index>
<bfr> Default is 0.
0: TA buffer of unsolicited result codes defined within this command is flushed to the
TE when <mode> 1…3 is entered (OK response shall be given before flushing the
codes)
1: TA buffer of unsolicited result codes defined within this command is cleared when
<mode> 1…3 is entered.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Syntax:
Command syntax: AT+CNMI=<mode>,<mt>,<bm>,<ds>,<bfr>
Command
Possible Responses
AT+CNMI=2,1,0,0,0
Note: <mt>=1
OK
AT+CMTI : “MT”,1
Note: message received
AT+CNMI=2,2,0,0,0
Note: <mt>=2
OK
+CMT : “8585551212”,”98/10/01,12 :30
00”,129,1,2,0,5<CR><LF>
Hello
Note: message received
AT+CNMI=2,0,0,1,0
OK
Note: <ds>=1
AT+CMGS=”8585551212”<CR>
Message to send <ctrl-Z>
Note: Send a message in text mode
+CMGS : 7
OK
Note: Successful transmission
+CDS : 2, 116, ”8585551212”, 129, “98/10/01,12 :30
:07”, “98/10/01 12 :30 :08”, 32768
Note: message was correctly delivered
Read Message +CMGR
Description: This command allows the application to read stored messages. The messages are read
from the memory selected by +CPMS command. A message read with status “REC
UNREAD” will be updated in memory with the status “REC READ”.
Note: The <stat> parameter for SMS Status Reports is always “READ”.
Values:
<stat> Status of message in memory. Possible values are as follows:
Text Mode Possible Values
Status of Messages in Memory
received unread messages
received read messages
stored unsent messages
stored sent messages
all messages
“UREAD”
“READ”
“USENT”
“SENT”
“ALL”
Note: For SMS Status Reports, only “ALL” and “READ” values of the <stat> parameter will
list messages ; other values will only return OK.
<oa/da>:
<mr>:
Origination/destination address value in string format.
Message Reference
<scts>:
Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
Discharge Time in string format: “yy/MM/dd,hh :mm :ss±zz” (Year [00-99],
Month [01-12], Day [01-31], Hour, Minute, Second and Time Zone [quarters
of an hour] )
<dt>:
<st>:
Status of a SMS-STATUS-REPORT (See Chapter 20)
Language
Encoding
<lang>:
<encod>:
<priority>:
Message priority:
0 – Normal
1 – Interactive
2 – Urgent
3 – Emergency
<cbn>:
Call Back Number
<length>:
<data>:
Length of the text message (in bytes).
Message text
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Syntax:
Command syntax: AT+CMGR=<index>
Response syntax: +CMGR: <stat> [,<oa>], <scts>, <lang>, <encod>, <priority>[,<cbn>],
<length> <CR><LF> <data> (for SMS-DELIVER only)
+CMGR: <stat> [,<da>], <dt>, <lang>, <encod>, <priority>[,<cbn>], <length> <CR><LF>
<data> (for SMS-SUBMIT only)
+CMGR: <stat>,<mr>,<scts>,<dt>,<st> (for SMS-STATUS-REPORT only)
Command
Possible Responses
+CMTI: “MT”,1
Note: New message received
+CMGR: “REC UNREAD”,”8585551212”,
”98/10/01,18 :22
AT+CMGR=1
Note: Read the message
:11+00”,1,2,0,”8585550000”,9<CR><LF>
ABCdefGHI
OK
AT+CMGR=1
Note: Read the message again
+CMGR: “REC READ”,”8585551212”, ”98/10/01,18
:22 :11”,1,2,0,”8585550000”,9<CR><LF>
ABCdefGHI
OK
Note: Message is read now
AT+CMGR=2
+CMS ERROR: 321
Note: Read at a wrong index
AT+CPMS=”SR”;+CNMI=,,,2
Reset to text mode, set read memory
to “SR”, and allow storage of further
SMS Status Report into “SR” memory
AT+CMSS=3
Note: Error : invalid index
+CPMS:0,10,0,10
OK
+CMSS: 160
Send an SMS previously stored
OK
+CDSI: “SR”,1
New SMS Status Report stored in “SR” memory at
index 1
AT+CMGR=1
Read the SMS Status Report
+CMGR: “READ”,160,
“8585551212”,129,”01/05/31,15:15:09”,
“01/05/31,15:15:09”,0
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
List Message +CMGL
Description: This command allows the application to read stored messages, by indicating the type of the
message to read. The messages are read from the memory selected by the +CPMS
command.
Values:
<index>: Place of storage in memory.
<stat>: Possible values, the status of messages in memory, are as follows:
Text Mode Possible Values
Status of Messages in Memory
received unread messages
received read messages
stored unsent messages
stored sent messages
all messages
“UREAD”
“READ”
“USENT”
“SENT”
“ALL”
Note: For SMS Status Reports, only “ALL” and “READ” values of the <stat> parameter will
list messages ; other values will only return OK.
<oa/da> : Origination/destination address value in string format.
<fo>:
First Octet, coded like SMS-SUBMIT first octet in document [4], default value is
17 for SMS-SUBMIT
<mr>:
Message Reference
<dt>:
Discharge Time in string format: “yy/MM/dd,hh :mm :ss±zz” (Year [00-99],
Month [01-12], Day [01-31], Hour, Minute, Second and Time Zone [quarters of
an hour] )
<st>:
<lang>:
Status of a SMS-STATUS-REPORT
Language
<encod>: Encoding
<length> : Length of the text message (in bytes).
<data>:
Message text
Syntax:
Command syntax: AT+CMGL=<stat>
Response syntax: +CMGL: <index>,<stat>,<da/oa>,<lang>,
<encod>,<length><CR><LF><data> (for SMS-DELIVER and SMS-SUBMIT, may be
followed by other <CR><LF>+CMGL:<index>…)
+CMGL: <index>,<stat>,<fo>,<mr>,<scts>,<dt>,<st> (for SMS-STATUS-REPORT only, may
be followed by other <CR><LF>+CMGL:<index>…)
Command
Possible Responses
AT+CMGL=“UREAD”
Note: List unread messages
in text mode
+CMGL: 1,”REC UNREAD”,”8585551212”,1,2,15
<CR><LF>Unread message!
+CMGL: 3,”REC UNREAD”, “8585551212”,
1,2,5<CR><LF>Hello
OK
Another message unread!
Note: 2 messages are unread, these messages will then have
their status changed to “REC READ” (+CSDH:0)
AT+CMGL=”READ”
Note: List read messages in
text mode
+CMGL: 2,”REC READ”,”8585551212”,1,2,9<CR><LF>
Keep cool
OK
AT+CMGL=”SENT”
Note: List stored and sent
messages in text mode
OK
Note: No message found
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Send Message +CMGS
Description: The <da> field is the address of the terminal to which the message is sent. To send the text
message, type <ctrl-Z> (0x1A) as the final character of the message. This command can be
aborted using the <ESC> (0x1B) character while entering the message text.
The <length> parameter is optional, it is used to set the length of the text string. When
<length> is specified, the CMGS command will only process the number of bytes specified
by <length> regardless of whether it contains <ctrl-Z>, <ESC>, or <backspace> characters.
The parameters <priority> and <cbn> are optional. When not specified, they default as
follows:
Priority: 0 (Normal)
Call back number: Not included in the message.
Values:
<da> : Destination address value in string format.
<length> : Length of the text message (in bytes).
<priority>: Message priority:
0 – Normal
1 – Interactive
2 – Urgent
3 – Emergency
<cbn>: Call Back Number
Note: If the “FD” facility is enabled, only the <da> entries in the FDN phonebook can be
sent.
Syntax:
Command syntax: AT+CMGS=<da> [,<length>] [,<priority>] [,<cbn>] <CR>entered text<ctrl-
Z / ESC>
Command
AT+CMGS=”8585551212”<CR>
Please call me soon, Fred. <ctrl-Z>
Note: Send a message
Possible Responses
+CMGS:<mr>
OK
Note: Message reference
output.
AT+CMGS=”8585551212”,12<CR>
Please call.<ctrl-Z>
+CMGS:<mr>
OK
Note: Send 12 byte message
Note: Message reference
output.
AT+CMGS=”8585551212”,2,1,1”5550000” <CR>
Please call ASAP<ctrl-Z>
+CMGS:<mr>
OK
Note: Send a message with the specified priority,
privacy, reply option and call back number. Notice
length field is omitted.
Note: Message reference
output.
AT+CMGS="12345"<CR>
+CMGS:<mr>
<Unicode message><0x00><0x1A>
Note: Unicode message without length field. Two byte
Unicode message <ctrl-Z> terminator.
AT+CMGS="1234",4
OK
Note: Message reference
output.
+CMGS:<mr>
<Unicode message><dummy byte>
Note: Unicode message with length. Final <dummy
byte> (any value) required for message transmission.
OK
Note: Message reference
output.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Write Message to Memory +CMGW
Description: This command stores a message in memory (SMS-SUBMIT). The memory location <index>
is returned (no choice possible as with phonebooks +CPBW). A text or Unicode message is
entered as described for the Send Message +CMGS command.
The <length> parameter is optional, it is used to set the length of the text string. When
<length> is specified, the CMGW command will only process the number of bytes specified
by <length> regardless of whether it contains <ctrl-Z>, <ESC>, or <backspace> characters.
The parameters <priority> and <cbn> are optional. When not specified, they default as
follows:
Priority: 0 (Normal)
Call back number: Not included in the message.
Values:
<oa/da> : Origination/destination address value in string format.
<length> : Length of the text message (in bytes).
<priority>: Message priority:
0 – Normal
1 – Interactive
2 – Urgent
3 – Emergency
<cbn>: Call Back Number
Syntax:
Command syntax: AT+CMGS= <oa/da> [,<length>] [,<priority>] [,<cbn>] <CR>
enter text <ctrl-Z / ESC>
Response syntax: +CMGW: <index> or +CMS ERROR: <err> if writing fails
Command
Possible Responses
AT+CMGW=”8585551212”<CR>
Hello how are you ?<ctrl-Z>
+CMGW: 4
OK
Note: Write a message
Note: Message stored in index 4
AT+CMGW=”8587777777”,6<CR>
Hello?<ctrl-Z>
+CMGW: <index>
OK
Note: Write a message with specified length of 6 bytes
AT+CMGW=”8585551212”,2,1,1”5550000”
Please call ASAP<ctrl-Z>
Note: Message stored in <index>
+CMGW: 5
OK
Note: Write message with the specified priority, privacy,
reply option and call back number. Notice length field is
omitted.
Note: Message stored in index 5
Send Message From Storage +CMSS
Description: This command sends a message stored at location value <index>.
Syntax:
Command syntax: AT+CMSS=<index>[,<da> [,<toda>] ]
Response syntax: +CMSS: <mr> or +CMS ERROR: <err> if sending fails
If a new recipient address <da> is given, it will be used instead of the one stored with the
message.
Command
Possible Responses
AT+CMGW=”8585551212”<CR>
Today is my birthday <CTRL-Z>
Note: Store message in phonebook.
AT+CMSS=5,8582221212
+CMGW : 5
OK
Note: Message stored with index 5
+CMSS: 1
Note: Send message 5 to a destination number OK
Note: Successful transmission. One SMS message sent
since power up.
AT+CMSS=5,8583331212
+CMSS: 2
Note: Send message 5 to a different destination OK
number Note: Successful transmission. Two SMS messages sent
since power up.
For response mode, <mr> is the number of SMS messages that have been sent since power
up. The maximum count is 65,535 messages.
Note: If the “FD” facility is enabled, only the <da> entries in the FDN phonebook can be set.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Delete Message +CMGD
Description: This command is used to delete one or several messages from preferred message storage.
Values:
<index>
0-9
When the preferred message storage is “BC”. Integer type values in the range of location
numbers of Message memory when the preferred message storage is “MT” or “SR”.
<DelFlag>
0 Delete message at location <index>
1 Delete All READ messages
2 Delete All READ and SENT messages
3 Delete All READ, SENT and UNSENT messages
4 Delete All messages.
Note: When the preferred message storage is “SR”, as SMS status reports are assumed to
have a “READ” status, if <DelFlag> is greater than 0, all SMS status reports will be deleted.
Syntax:
Command syntax: AT+CMGD=<Index> [,<DelFlag>]
Command
Possible Responses
+CMTI:”MT”,3
Note: New message received
AT+CMGR=3
Note: Read it
+CMGR: “REC UNREAD”,”8585551212”,
“98/10/01,18 :19 :20”,1,2,0,17 <CR><LF>
Message received!
OK
Note: Unread message received from 8585551212 on the 01/10/1998 at
18H19m 20s
AT+CMGD=3
Note: Delete it
AT+CMGD=1,0
OK
Note: Message deleted
OK
Note: The message from the preferred message storage at the location 1 is
deleted
AT+CMGD=1,1
AT+CMGD=1,2
AT+CMGD=1,3
AT+CMGD=1,4
OK
Note: All READ messages from the preferred message storage are deleted
+CMS ERROR:321
Note: NV Error deleting READ messages and SENT (no messages to delete)
OK
Note: All READ, SENT and UNSENT messages are deleted
OK
Note: All messages are deleted
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Select Broadcast Messages +CSCB
Description: This command turns on/off the reception of Broadcast SMS messages.
Values:
The <bm> parameter of +CNMI command controls the indication of an incoming BC SMS
message.
<mode>:
0: Activates reception of BC SMS.
1: Turns off reception of BC SMS. Emergency BC SMS will be received in this mode.
Syntax:
Command syntax: AT+CSCB=<mode>
Command
Possible Responses
AT+CSCB=0
OK
Note: Turn on reception of BC SMS
Note: BC SMS can be received
+CBMI: “BC”,5
Note: A BC SMS was received, and stored in slot 5
AT+CSCB=1
OK
Note: Turn off reception of BC SMS
Note: Only Emergency BC SMS can be received.
Reception of all other BC SMS will be stopped.
Message Status Modification +WMSC
Description: This command is used to change the status of one message from preferred message
storage.
Values:
<loc> Location number of the stored message (integer)
<status> new status to be stored, as for +CMGL command :
Text Mode
“UREAD”
“READ”
“USENT”
“SENT”
Possible responses:
OK
Location is valid and has been changed
Non-volatile memory error
Invalid index (out of range or no SMS stored)
if attempting to change Status Report SMS or if syntax is
incorrect
+CMS ERROR: 341
+CMS ERROR: 321
+CMS ERROR: 302
Note: Status of SENT or USENT indicate changing MO memory SMS. Status of READ or
UREAD implies using preferred memory. Changes are not accepted when preferred memory
is set to Status Report (all status reports are always assumed to be READ and cannot be
changed).
Syntax:
Command syntax: AT+WMSC= <loc>, <status>
Command
Possible Responses
AT+WMSC=4,”UREAD”
OK
Note: Message stored in preferred memory index 4 status
changed to NOT READ
AT+WMSC=8,”USENT”
AT+CPMS=”SR”
+CMS ERROR: 321
Note: Invalid index, no message at location 8 of MO memory
+CPMS:1,10,4,10
Note: Change preferred memory to Status OK
Report
AT+WMSC=0,”UREAD”
+CMS ERROR: 302
Note: Cannot change Status Report messages
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Message Overwriting +WMGO
Description: The +CMGW command writes an SMS to the first location available. To write an SMS to a
specified location, the +WMGO command forces the product to write an SMS (with the
+CMGW command) to the location specified with +WMGO, but for just one +CMGW
command.
Values:
Syntax:
<loc>: Location number of the record to write or overwrite
Command syntax: AT+WMGO= <loc>
Command
Possible Responses
AT+WMGO=0
OK
Note: Next MSG write will be to index 0
AT+WMGO=30
+CMS ERROR: 302
Note: Invalid index (out of range)
On the next AT+CMGW command, the record number used will be the one specified by the
AT+WMGO command. The location is forgotten and, in order to perform a second overwrite,
+WMGO has to be used again.
If the external application specifies a free location, and if an incoming message is received
before the AT+CMGW command, the product may store the incoming message at a location
available. This could be the one specified by +WMGO (the product does not prevent from
this). If the user then issues an AT+CMGW command without changing the AT+WMGO
location, the new message will be overwritten!
Note: that this location number is not kept over a software reset.
Change SMS Status +WUSS
Description: The +WUSS command enables or disables a change of the SMS message status following
a +CMGR or +CMGL command.
Values:
Syntax:
<mode>:
0: The SMS Status will change.
1: The SMS Status will not change.
Command syntax: AT+WUSS = <mode>
Command
Possible Responses
AT+WUSS=1
AT+WUSS=0
OK
OK
Note: If lower layer failure, +CMS ERROR: 513
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 – Short Messages Commands
Set SMS Compose Language and Encoding +WSCL
Description: The +WSCL command sets the SMS composition language and encoding types. When
composing a message (+CMGS, +CMGW), the SMS language and encoding fields will be
set using the current +WSCL value.
Values:
<lang>
0: Unspecified
1: English
2: French
3: Spanish
4: Japanese
5: Korean
6: Chinese
7: Hebrew
<enc>
0: Octet (or Unspecified)
1: IS91EP
2: ASCII
3: IA5
4: UNICODE
Syntax:
Command syntax: AT+WSCL = <lang>, <encod>
Command
Possible Responses
AT+WSCL=1,2
OK
Note: Set language to English, encoding to ASCII
AT+CMGW=”8585551212”<CR>
Hello how are you ?<ctrl-Z>
Note: Write a message in English
AT+WSCL=6,4
+CMGW: 4
OK
Note: Message stored in index 4
OK
Note: Set language to Chinese, encoding to UNICODE
AT+CMGS=”8585551212”<CR>
Ãû×Ö<ctrl-Z>
+CMGS: <mr>
OK
Note: Send a message in Chinese
Note: Message sent
Set Timestamp of MT SMS +WSTM
Description: The +WSTM command sets the timestamp that will be used when the modem receives a
Mobile Terminated SMS. When a new MT SMS message is received the setting of this
command determines if the timestamp that was received with the message is kept, or
modem’s CDMA time, which represents the actual time of message arrival is used. When
choosing to use modem’s CDMA time, the command gives the option of using local or GMT
time.
Values:
<ts>
0: Original Time Stamp of the received MT SMS
1: Time of arrival – GMT Time
2: Time of arrival – Local Time
Syntax:
Command syntax: AT+WSTM = <ts>
Command
Possible Responses
AT+WSTM=2
OK
Note: Set MT SMS timestamp to time of arrival (local time zone)
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 – Supplementary Service Commands
CHAPTER 9 - SUPPLEMENTARY SERVICES COMMANDS
Supplementary Service commands are specialized call processing commands used to control carrier
features on the modem such as caller ID, call forwarding, call waiting, 3-way calls, and specialized CDMA
test calls.
Call Forwarding +CCFC
Description: This command allows control of the call forwarding supplementary service, if supported by
the carrier. All calls will be forwarded unconditionally to the phone number specified. The
modem will make a brief call to the CDMA network using an ATD specified prefix number
(country and carrier specific) to setup or cancel call forwarding. An audio tone will be
produced in the audio path to confirm the change of the call forwarding state.
Values:
Syntax:
<number>: The phone number to forward all calls to.
Note 1: Country and carrier specific call forwarding services (e.g. *68, *72, etc.) may also be
available to the host application in addition to the modem provided +CCFC functionality. The
host application can utilize these enhanced services for call forwarding with the modem ATD
command (e.g. ATD*72).
Note 2: If the “FD” facility is enabled, only the entries in the FDN phonebook can be
forwarded.
Command syntax: AT+CCFC= <number>
Command
Possible Responses
ATD*72
OK
Note: Specify the call forwarding
prefix number.
Note: Prefix number set.
OK
AT+CCFC=8585551212
Note: Register to an unconditional call
forwarding.
+WORG:*728585551212
+WCNT:3
Note: Call forwarding active for all incoming calls to phone number
858-555-1212
AT+CCFC=0
OK
Note: Cancel unconditional call
forwarding
+WORG:*720
+WCNT:3
Note: Call forwarding cancelled.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 – Supplementary Service Commands
Calling Line Identification Restriction +CLIR
Description: This command allows control of the outgoing caller ID restriction supplementary service.
Values:
<mode>: sets the caller ID restriction for outgoing calls
0: Outgoing Caller ID works normally, according to the subscription of the Caller ID
service.
1: Outgoing Caller ID is restricted. The called party will see ‘Restricted’ on their Caller ID
display.
Note that this command works by automatically pre-pending a *67 to the outgoing dialing
string. Thus, this command will only work on CDMA networks that recognize a *67 to
suppress outgoing caller ID. Also, the original dialing string cannot be longer than 29
characters in length.
Syntax:
Command syntax: AT+CLIR=<mode>
Command
AT+CLIR=1
Possible Responses
OK
Note: Restrict outgoing caller ID.
AT+CLIR?
Note: Ask for current functionality
Note: Command valid
+CLIR :<mode>
OK
Note: <mode> as defined below
Calling Line Identification Presentation +CLIP
Description: This command allows control of the incoming caller ID presentation supplementary service.
When presentation of the CLI (Calling Line Identification) is enabled (and the carrier allows),
+CLIP response is returned after the RING unsolicited result code. By default, +CLIP is
enabled.
Values:
<mode>: parameter enable or disables the caller ID unsolicited command
0: Disable
1: Enable
Syntax:
Command syntax: AT+CLIP=<mode>
Command
Possible Responses
AT+CLIP=1
OK
Note: Enable CLIP
Note: CLIP is enabled
AT+CLIP?
+CLIP:<mode>
Note: Ask for current functionality
OK
Note: <mode> defined as below
RING
Note: Incoming call
+CLIP: “8585551212”,129
Note: Incoming call with number presentation
OK
AT+CLIP=0
Note: Disable CLIP presentation
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 – Supplementary Service Commands
Send Flash to Base Station +WFSH
Description: This command sends a flash or flash with information to the base station. The flash
command is used to manage call waiting and 3-way calls. For call waiting situations when
the 3 party call is received, send a flash (AT+WFSH) to toggle between the two different call
parties. The +WFSH unsolicited AT command will be returned if a flash was sent to the base
station over the air. Note that on CDMA networks, this does not guarantee that an actual
switch between calls took place, because there is no acknowledgement to the modem. For
3-way calls, initiate the first call to party # 1 (see ATD). Then send a flash with information
(AT+WFSH=18005551212) to initiate a call to party # 2, party # 1 will automatically be
placed on hold. The “information” is the phone number of party # 2. Once a conversation
with party # 2 is established, send a regular flash (AT+WFSH) to connect all 3 parties. Send
another flash (AT+WFSH) to disconnect party # 2, or End call (see ATH) to end the call with
all parties. rd
Syntax:
AT+WFSH
Command syntax: AT+WFSH
Command syntax AT+WFSH= < phone_number > (for a flash with information)
Unsolicited result syntax: +WFSH (confirms a flash was sent to the base station)
Command
ATD8585551212;
Note: Make a voice call
Possible Responses
OK
+WORG:8585551212
+WCNT:3 Note: Conversation…
+CCWA:”8582701234”,129
Note: Indication of another incoming call
OK
+WFSH
AT+WFSH
Note: Send a flash to the Base Station (toggle to the second
call).
Note: Flash sent to the Base Station. Call to the
second call. However, this is not 100%
guaranteed because there is no confirmation
from the Base Station.
Note: Conversation with second call.
AT+WFSH
OK +WFSH
Note: Send a flash to the Base Station (toggle to the first call).
Note: Flash sent to the Base Station. Call
switches to the first call. However, this is not
100% guaranteed because there is no
confirmation from the Base Station.
OK
ATH
Note: Release the all calls
+WEND:10
Note: All Calls End
ATD858551212
OK
Note: Make a voice call
+WORG:858551212
+WCNT:3
Note: Conversation
OK
+WFSH
Note Modem now places first call on hold and
attempts connection to second call.
AT+WFSH=6195552121
OK
Note: Place first call on hold, connect to second party.
+WFSH
Note: All 3 parties now connected.
AT+WFSH
OK
Note: Connect all 3 parties.
+WFSH
Note: Disconnect second party, connected to
first party only.
AT+WFSH
ATH
OK
+WEND:10
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9 – Supplementary Service Commands
List Current Call State +CLCC
Description: This command is used to return the current call state of the modem.
Values:
<state> (state of the call):
0: no call
1: traffic
2: dialing (MO call)
3: incoming (MT call)
<mode> (teleservice) :
0: voice
1: data
2: fax
3: sms
4: otasp
5: markov or loopback
9: unknown or not applicable
<termination>
0: unknown or not applicable
1: mobile terminated (MT) call
2: mobile originated (MO) call
Syntax:
Command syntax: AT+CLCC
+CLCC: <state>, <mode>, <termination>
Command
Possible Responses
AT+CLCC
Note: Seek current phone state
+CLCC: 0,9,0
OK
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 – Data Commands
CHAPTER 10 - DATA COMMANDS
Using AT Commands During a Data Connection
To use AT Commands during a data connection (e.g. while the product is in online mode), it is necessary
either to switch to offline mode, or to use the +WMUX command to enable Commands / Data multiplexing.
Note: currently the +WMUX command is not supported yet.
Switch From Online to Offline Mode
To switch from online mode to offline mode, the “+++” sequence must be sent. Following this, the product
gets back to offline mode with an “OK” response, and an AT command can be sent.
Note: the “+++” sequence only works with the +ICF command using the following settings:
•
•
8 data bits, with no parity
7 data bits, with even parity
Switch From Offline to Online Mode
See the ATO command description.
Select Mode +FCLASS
Description: This command puts the product into a particular operating mode for fax.
Values:
<n>
0: Data
1: Fax class 1
2.0: Fax class 2.0
Syntax:
Command syntax: AT+FCLASS= <n>
Command
Possible Responses
AT+FCLASS=?
+FCLASS: 0, 2.0
Note: Test command
OK
Note: If fax class 1 not supported
AT+FCLASS=0
OK
Note: Data mode requested
Note: Command valid
AT+FCLASS=2.0
OK
Note: Fax class 2 mode requested
AT+FCLASS?
Note: Current value
Note: Command valid
+FCLASS: 2.0
OK
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 – Data Commands
Cellular Result Codes +CRC
Description: This command gives more detailed ring information for an incoming call. Instead of the
string “RING”, an extended string is used to indicate which type of call is ringing (e.g.
+CRING:VOICE).
These extended indications are:
+CRING:VOICE
+CRING:DATA
+CRING:FAX
for normal voice calls
for all types of data calls
for all types of fax calls
+CRING:OTAPA
+CRING:TEST
+CRING:UNKNOWN
for OTAPA calls
for markov, loopback, and test calls
for unknown/undefined calls types
Syntax:
Command syntax: AT+CRC
Command
Possible Responses
AT+CRC=0
OK
Note: Extended reports disabled
Note: Command valid
AT+CRC=1
OK
Note: Extended reports enabled
Note: Command valid
DTE-DCE Local Rate Reporting +ILRR
Description: This parameter controls whether or not the extended-format “+ILRR:<rate>” information text
is transmitted from the DCE to the DTE. Currently the product only supports 0 = OFF.
Values:
Syntax:
<value>
Decimal number corresponding to the selected option. Currently, only 0 is supported
(disables reporting of local port rate).
Command syntax: AT+ILRR=<value>
Command
Possible Responses
AT+ILRR=0
Note: Local port
rate report
OK
Note: Command valid
disabled
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 – Data Commands
V42 Bis Data Compression +DS
Description: This command enables or disables V.42bis data compression if this feature is provided on
the PSTN in the IWF.
Values:
Four numeric sub-parameters are accepted:
< dir >: specifies the desired direction(s) of operation of the data compression function; from
the DTE point of view, (default is 3),
0: Negotiated … no compression
1: Transmit only
2: Receive only
3: Both directions, accept any direction
< neg >: specifies whether or not the DCE should continue to operate if the desired result is
not obtained, (default is 0),
0: Do not disconnect if V.42 bis is not negotiated by the remote DCE as specified in
<dir>
1: Disconnect if V.42 bis is not negotiated by the remote DCE as specified in <dir>
< P1 >
512-4096: specifies the maximum number of dictionary entries that should be
negotiated, (default is 4096),
< P2 >
6-250: specifies the maximum string length to be negotiated, (default is 250).
Syntax:
Command syntax: AT+DS=<dir>,<neg>,<P1>,<P2>
Command
Possible Responses
AT+DS=3,0,4096,250
Note: Set new parameters
AT+DS?
OK
Note: Command valid
+DS: 3,0,4096,250
OK
Note: Current values
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10 – Data Commands
V42 Bis Data Compression Report +DR
Description: This command returns the results of data compression capability. If data reporting is
enabled, this command returns the data compression type of an incoming or outgoing data
call. Otherwise, the command returns NONE.
The intermediate result code represents current DCE-DCE data compression type. The
syntax for +DR reporting is: +DR<result>, and the result code is defined as follows:
+DR: NONE
Data compression is not in use
+DR: V42B
Rec. V.42 bis is in use in both directions
Rec. V.42 bis is in use in receive direction only
Rec. V.42 bis is in use in transmit direction only
+DR: V42B RD
+DR: V42B TD
The +DR intermediate result code, if enabled, is issued before the final result code, before
the +ILRR intermediate report and after the service report control +CR.
Values:
Syntax:
This syntax is for setting the +DR reporting method.
<val>
0: Disable reporting
1: Enable reporting
Command syntax: AT+DR=<val>
Command
Possible Responses
AT+DR=1
OK
Note: Reporting enabled
Note: Command valid
AT+DR?
+DR: 1
Note: Display the current value
OK
Note: Command valid
AT+DR=?
+DR: (0,1)
Note: Display the supported values
OK
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 – V24-V25 Commands
CHAPTER 11 – V. 2 4 -V.2 5 COMMANDS
Refer to ITU-T Recommendation V.25 per specification for more details on the following commands.
Fixed DTE Rate +IPR
Description: This command specifies the data rate at which the DCE will accept commands.
Syntax:
Command syntax: AT+IPR
Command
Possible Responses
AT+IPR?
+IPR: 9600
Note: Read syntax.
OK
Note: Current rate is 9600 bps
AT+IPR=?
+IPR: (0,1200,2400,4800,9600,19200), (45,50,75,
Note: List of supported <rate> values,[(list 110,150,300,600,38400,57600,115200,230400)
of fixed-only <rate> values)]
OK
Note: Possible value (*)
AT+IPR=38400
OK
Note: Disable autobaud and set rate to
38400 bps
AT+IPR=0
OK
Note: Enable autobaud
(*) the first set of values indicates the range of auto-detectable speeds. The second set of
values indicates all possible speeds that can be used by the DCE. The DCE supports
Autobaud based on the data sent from the DTE.
DTE-DCE Character Framing +ICF
Description: This command is used to determine the local serial port start-stop (asynchronous) character
framing that the DCE uses.
Values:
<format>
0: Autodetect (Not supported)
1: 8 Data 2 Stop (Not supported)
2: 8 Data 1 Parity 1 Stop (Not supported)
3: 8 Data 1 Stop (Supported)
4: 7 Data 2 Stop (Not Supported)
5: 7 Data 1 Parity 1 Stop (Not Supported)
6: 7 Data 1 Stop (Not Supported)
<parity>
0: Odd (Supported)
1: Even (Supported)
2: Mark (Supported)
3: None (Supported)
Note: The Rm interface is only supported at 8 data bits, No Parity, 1 stop bit. ERROR is
returned for other formats.
Syntax:
Command syntax: AT+ICF= <format>, <parity>
Command
Possible Responses
AT+ICF=3,3
OK
Note: Set values.
AT+ICF?
Note: New values set
+ICF: 3,3
Note: Display current settings.
OK
Note: Current values
+ICF: (3-3),(0-3)
OK
AT+ICF=?
Note: Display valid parameter ranges.
Note: Possible values
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 – V24-V25 Commands
DTE-DCE Local Flow Control +IFC
Description: This command is used to control the operation of local serial connection flow control
between the data terminal device and the mobile.
Values:
<Tx>
0: None
1: XON/XOFF Remove Xon (0x19) and Xoff (0x17) characters from data stream.
2: Hardware Use RTS (Request To Send) signal (default)
3: XON/XOFF Leave Xon (0x19) and Xoff (0x17) characters in data stream.
<Rx>
0: None
1: XON/XOFF Remove Xon (0x19) and Xoff (0x17) characters from data stream.
2: Hardware Use CTS (Clear To Send) signal (default)
Transmit data flow control disabled.
Receive data flow control disabled.
Syntax:
Command syntax: AT+IFC=<Tx>,<Rx>
Command
Possible Responses
AT+IFC=?
+IFC: (0-3),(0-2)
Note: Display valid parameter ranges.
OK
Note: Valid parameter ranges
AT+IFC?
+IFC: 2,2
Note: Display current settings.
OK
Note: Default values are 2,2 (hardware flow control).
AT+IFC=3
OK
Note: Set Tx flow control to XON/XOFF.
Note: New Tx flow control value set.
AT+IFC=,1
OK
Note: Set Rx flow control to XON/XOFF.
AT+IFC?
Note: New Rx flow control value set.
+IFC: 3,1
Note: Display current settings.
OK
Note: Settings displayed.
AT+IFC=2,2
OK
Note: Set Tx and Rx flow control to hardware.
Note: New Tx and Rx flow control values set.
Set DCD Signal &C
Description: This command controls the Data Carrier Detect (DCD) signal.
Syntax:
Command syntax: AT&C
Command
Possible Responses
OK
AT&C0
Note: DCD always on
Note: Command valid
AT&C1
OK
Note: DCD matches state in accordance with
the specified service
Note: Command valid
AT&C2
OK
Note: Wink indicator on channel disconnect
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 – V24-V25 Commands
Set DTR Signal &D
Description: This commands controls the Data Terminal Ready (DTR) signal.
Values:
<n>
0: The DTR signal is ignored.
1: Enter online command state following ON-to-OFF transition of circuit 108/2
2: Enter command state following ON-to-OFF transition of circuit 108/2.
Syntax:
Command syntax: AT&D<n>
Command
Possible Responses
AT&D0
OK
Note: The DTR signal is ignored
Note: Command valid
AT&D1
OK
Note: Enter online command state following ON-to-OFF transition of circuit 108/2
AT&D2
Note: Command valid
OK
Note: Enter command state following ON-to-OFF transition of circuit 108/2
Note: Command valid
Set DSR Signal &S
Description: This commands controls the Data Set Ready (DSR) signal.
Values:
<n>
0: The DSR signal is always on.
1: The DSR signal is always off.
Syntax:
Command syntax: AT&S<n>
Command
AT&S0
Possible Responses
OK
Note: The DSR signal always on.
Note: Command valid
AT&S1
OK
Note: The DSR signal is always off.
Note: Command valid
Back to Online Mode O
Description: If a connection has been established and the MS is in command mode, this command allows
you to return to online data mode.
Syntax:
Command syntax: ATO
Command
ATO
Possible Responses
OK
Note: Return to online mode from offline mode
ATO
NO CARRIER
Note: Return to online mode from offline mode
Note: Not in a call
Result Code Suppression Q
Description: This command determines whether the mobile equipment sends result codes or not.
Syntax:
Command syntax: ATQ
Command
ATQ0
Possible Responses
OK
Note: Return result codes
Note: Command valid
ATQ1
(none)
Note: Result codes are suppressed and not transmitted
Note: No response
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 – V24-V25 Commands
DCE Response Format V
Description: This command specifies the DCE result code format; with or without the header characters
<CR><LF> and the use of numeric result codes. Numeric result codes are available for AT
commands only. Result codes, both word and numeric, can be suppressed by the ATQ
command.
Unsolicited responses (see Chapter 3) are not affected by the ATV command and will
always
be displayed in word format as documented .
Note: The unsolicited response +RING is not affected by the ATV command. The +RING
response can be formatted by the +CRC command.
Syntax:
Command syntax: ATV
Command
Possible Responses
ATV0
0
Note: Display result codes as numbers
Note: Command is valid (0 means OK)
ATV1
OK
Note: Display result codes as words (Default)
Note: Command valid
Auto-Tests &T
Description: AT&T1 is used to perform audio loop back in the current audio path. This command can be
used to validate the audio loop.
Values:
Syntax:
<num>
0: Not defined; returns OK.
1: Audio loopback on for current path.
2: Audio loopback is off.
Command syntax: AT&T<num>
Command
Possible Responses
AT&T1
OK
Note: Audio loopback is on.
AT&T2
OK
Note: Audio loopback is off.
Echo E
Description: This command is used to determine whether or not the modem echoes characters received
by an external application (DTE).
Syntax:
Command syntax: ATE
Command
Possible Responses
ATE0
OK
Note: Characters are not echoed
Note: Done
ATE1
OK
Note: Characters are echoed
Note: Done
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 – V24-V25 Commands
Display Configuration &V
Description: This command is used to display the modem configuration. It lists all the commands
supported by the modem and their possible parameters.
Values:
<num>
0: Manufacturer data
1: Not used
2: Not used
3: Software revision data
4: Not used
5: Configuration data
6: Capability data
7: Not used
Note: For the data returned by the ATI6 command, the use of the IS-707 +GCAP command
is preferred.
Syntax:
Command syntax: AT&V
Command
Possible Responses
AT&V
&C: 2; &D: 2; …
Note: Display the active parameter settings
…
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 11 – V24-V25 Commands
Request Identification Information I
Description: This command causes the product to transmit one or more lines of information from the
DCE.
Syntax:
Command syntax: ATI<num>
Command
Possible Responses
ATI0
MODEM
Note: Display manufacturer data
800 1900
OK
ATI3
S/W VER: WISMOQ …
Note: Display software revision data
OK
ATI6
+CGSM, +CIS707, …
OK
Note: Display capability data
Restore Factory Setting &F
Description: This command is used to restore the factory setting from NV memory. The settings that are
affected by this command are shown in Chapter 20. This command will reset the modem as
the very last part of its operation.
Syntax:
Command syntax: AT&F
Command
Possible Responses
AT&F
OK
Note: Command valid, modem resets
Save Configuration &W
Description: This command writes the current configuration to NV. See table in Chapter 20 for a list of
items.
Syntax:
Command syntax: AT&W
Command
Possible Responses
AT&W
OK
Note: Command valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 – Phone Book Commands
CHAPTER 12 - PHONE BOOK COMMANDS
In this chapter, the AT commands are used to operate on mobile phonebook. These phonebook commands
adhere to the set defined in GSM 07.07 specification. Please refer to GSM 07.07 for further AT command
usage and description.
For all phonebook read commands (+CPBR, +CPBF, +CPBP), the TON/NPI MSB of each number is set to 1
(ex: a TON/NPI stored as 17 is displayed as 145).
When accessing numbers in the call history phonebooks (“LD”, “MC”, or “RC”), if a matching number is found
in one of the other phonebooks, the text portion of the matching entry is copied to the call history entry.
The phone book “SM” is only supported in an RUIM capable modem.
When an RUIM is present, the “MT” phonebook is a combination of two phonebooks as shown in the
example below. This must be taken into account when using a phone book AT command index to access an
entry in this phonebook.
ME Index range 1 to 100
SM Index range 1 to 150 (SIM card)
MT ME start at 1, SM start at 101 (SIM
card)
< - - - - - - - ME - - - - - - -> < - - - - - - -
SM - - - - - - - - ->
1 100 101 250
Select Phonebook Memory Storage +CPBS
Description: This command selects the type of memory where the phonebook will be stored. Possible
phone books are listed below under the <bk> section. If there’s no RUIM card present,
selecting “SM” phonebook returns ERROR.
Syntax:
Command syntax: AT+CPBS=”<bk>”
Command
Possible responses
AT+CPBS=?
+CPBS: (“ME”,”MC”,”LD”,”RC”,”EN”)
Note: Possible values, not all may be supported
Note: Not all may be supported
AT+CPBS=”EN”
OK
Note: Select the emergency phonebook
AT+CPBS?
Note: Emergency phonebook selected
+CPBS: EN,0,9
Note: Return the currently selected phonebook
OK
Note: EN phonebook selected, 0 locations used,
9 available
AT+CPBS=”MT”
OK
Note: Select the MT phonebook (RUIM present).
AT+CPBS?
Note: MT phonebook selected
+CPBS: MT,5,300
Note: Display MT phonebook information.
Combination of ME and SM phonebooks.
OK
Note: 5 locations used, 300 available
(combination of ME and RUIM phonebooks).
<bk>:
“SM”: ADN (RUIM phonebook)
“ME”: ME (ME NV phonebook)
“LD”: LND (ME or RUIM last dialed phonebook; depending on presence of RUIM)
“EN”: EN (ME NV emergency numbers)
“MC”: MSD (ME missed calls list)
“MT”: MT (combined ME and RUIM phonebook)
“RC”: LIC (ME received calls list)
“FD”: FDN (SIM Fix Dialing, restricted phonebook)
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 – Phone Book Commands
Return Selected Phonebook Locations +CPBU
Description: This command returns information about the currently selected phonebook. This includes
the starting entry location, the total number of locations, maximum length of the phone
number, the TON/NPI value range, and the maximum number of characters for the text
portion of each entry.
The format of the returned data for the “MT” phonebook is different. It is a combination of the
“ME” and “SM” phonebooks with values that describe each.
Syntax:
Command syntax: AT+CPBU?
Command
Possible Responses
AT+CPBS=”ME”
OK
Note: Select the ME phonebook.
AT+CPBU?
Note: ME phonebook selected
+CPBU: (1 –100),32,(0-255),12
OK
Note: Display ME phonebook
information.
AT+CPBS=”MT”
Note: 100 locations starting at 1, 32 digits maximum, TON/NPI
value range is 0-255, and 12 characters for the text.
OK
Note: Select the MT phonebook.
AT+CPBU?
Note: MT phonebook selected
+CPBU: (1-100,101-180),(32,20),(0-255),(12,12)
OK
Note: Display MT phonebook
information.
Note: 100 locations starting at 1 for the ME phonebook, 80
locations starting at 101 for the SM phonebook, 32 digits maximum
for the ME phonebook and 20 digits maximum for the SM
phonebook, TON/NPI value range is 0-255, and 12 characters for
the text in both the ME and SM phonebooks.
Find Phonebook Entries +CPBF
Description: This command returns the first ten phonebook entries with alphanumeric fields starting with
a given string. The user can use a string that is more exact to ensure that the entry they are
looking for is found. The string search is case sensitive.
When the “MT” phonebook is selected, the find operation searches the “ME” portion first
followed by the “SM” portion. The returned values may be a combination of entries from both
the “ME” and “SM” phonebooks.
Note: This command is functional for the “ME”, “EN”, “SM”, and “MT” phonebooks only.
Syntax:
Command syntax: AT+CPBF=”string”
Command
Possible Responses
AT+CPBF=”TES”
+CPBF: 1,”6195551212”,145,”test1”
OK
Note: Displays location starting with “TES”
AT+CPBF=”NEXT”
+CME ERROR: 22
Note: Find entries that start with “NEXT”
Note: Entry not found
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 – Phone Book Commands
Write Phonebook Entry +CPBW
Description: This command writes a phonebook entry to location <index> in the current phonebook
selected with the +CPBS command.
If the “MT” phonebook is selected, <index> is in the range of the combined “ME” and “SM”
phonebooks. When using auto address mode (<index> not specified in the command), the
“ME” phonebook is accessed first for an available location. If a location is not available in the
“ME” phonebook, the “SM” phonebook is accessed.
The +WSPC command must be issued with a valid SPC code value before entries in the
“EN” phonebook can be changed.
Values:
<index> Integer type value depending on the capacity of the currently selected phonebook.
<phoneNumber> Phone number is in ASCII format. Valid characters are 0-9 and *, #, -.
<TON/NPI> Type of address in integer form. The MSB of this will always be set high.
<text string>Any text string.
Note: PIN2 verification is required to do this command on the FDN. If the PIN2
authentication has been performed during the current session, the +CPBW command with
FDN is allowed.
Command
Possible Responses
AT+CPBS=”FD”
OK
Note: Select FDN phonebook
AT+CPBW=5,”8585551212”,145,”test”
Note: Write in FDN at location 5
+CME ERRO: 17
Note: PIN2 is required
AT+CPIN2?
RUIM PIN2
Note: SIM PIN2 is required
AT+CPIN2=1234
OK
Note: Example PIN2 entered
Note: PIN2 successfully entered
AT+CPBW=5,”8585551212”,145,”test”
Note: Write in FDN at location 5
OK
Note: Write in FDN successful
Syntax:
Command syntax: AT+CPBW=<index>,”<phoneNumber>”,<TON/NPI number>,”<text
string>”
Command
Possible Responses
AT+CPBW=1,”6195551212”,145,”test1”
OK
Note: Data stored in location 1.
AT+CPBW=2
OK
Note: Erase location 2
AT+CPBW=1,”8585551212”,145,”test1”
Note: Location 1 overwritten
OK
AT+CPBW=80,”8585551212”,145,”test80
Note: Error left off trailing quotes
AT+CPBW=,”8585551212”,145,”test”
Note: Write to the first open location
AT+CPBW=,”8585551212”,145,”FullBook”
Note: Phone book is full
ERROR
OK
+CME ERROR: 20
Note: Phonebook full
AT+CPBW=,”8585551212”,145,”Text is too long for this ”
Note: Write to first location that is open 24 ASCII characters
+CME ERROR: 24
Note: Text string exceed maximum character
length
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 – Phone Book Commands
Phonebook Read +CPBR
Description: This command returns phonebook entries from a range of locations from the currently
selected phonebook.
When the “MT” phonebook is selected, a request for the range 95 through 105 will return
locations 95 through 100 of the “ME” phonebook and locations 1 through 5 of the “SM”
phonebook (“MT” phonebook locations 101 through 105).
Note: There are only 9 entries total in the Emergency Numbers phonebook (1 – 9).
Syntax:
Command syntax: AT+CPBR=<first>[,last]
Command
Possible Responses
AT+CPBR=1
AT+CPBR=1,3
Note: Read location 1 to 3 and return and data they
+CPBR:1,”6185551212”,145,”test”
+CPBR:1,”6185551212”,145,”test1”
+CPBR:2,”6185551212”,129,”test2”
may contain. Only 10 entries starting at the first entry +CPBR:3,”6185551212”,115,”test3”
are displayed. User can enter command multiple
times with different indices.
AT+CPBR=12,1
Note: The MSB of the TON/NPI is ALWAYS set high
ERROR
Note: <x,y> where x<y
Note: Invalid range x>y
AT+CPBR=300
+CMEE:21
Note: Invalid index
Note 1: When the range is more than 10, only the first 10 hit entries will be displayed.
Note 2: For the LD, MC, and RC phonebooks, the TON/NPI number will not be displayed.
Phonebook Search +CPBP
Description: This searches the currently selected phonebook for a phone number match and returns the
entry if found. The search looks for the exactly number string match.
When the “MT” phonebook is selected, the search operation searches the “ME” portion first
followed by the “SM” portion.
Syntax:
Command syntax: AT+CPBP= ”<phone number>”
Command
Possible Responses
AT+CPBP= ”8585551212”
Note: Find ”8585551212” in
current phonebook if it exists.
+CPBP=1,”8585551212”,145,”FullBook”
OK
Note: ME phone book previously selected. Display the entry that
matches.
AT+CPBP=”123”
+CME ERROR: 22
Note: Entry not found
Note: The phone number to search should match that stored in phone book. Partial number
searching is not supported and will return an error.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 12 – Phone Book Commands
Avoid Phonebook Init +WAIP
Description: This command controls access to the available phonebooks. If +WAIP is set to 1,
phonebook entries are not accessible. When +WAIP is set to 0, access to phonebook
entries is permitted.
Syntax:
Command syntax: AT+WAIP=<mode>
Command
Possible Responses
AT+WAIP?
+WAIP: 1
Note: No phonebook commands are allowed after boot. If a command is
entered it returns “+CMEE ERROR: 3”
AT+WAIP=?
AT+WAIP=1
+WAIP: (0-1)
OK
OK
AT&W
Note: Save value to NV
<mode>
0: Normal operating mode. Enable.
1: No phonebook initialization. Disable.
Delete Calls From Phonebook +WDCP
Description: This command will delete all entries from a selected phonebook if it supports this feature.
Typically, +WDCP is used to delete the calls stored in LD, MC, and RC phonebooks.
Values:
Syntax:
<call phonebook>:
LD, MC, or RC
Command syntax: AT+WDCP=”<call phonebook>”
Command
Possible Responses
AT+WDCP?
+WDCP: “LD”
Note: Returns phonebook(s) that support deleting calls.
AT+WDCP=?
+WDCP: (“LD”,”MC”,”RC”)
Note: Possible supported phonebooks
AT+WDCP=”LD”
OK
Note: Erase call history for last dialed phone book
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 – Position Determination (GPS) AT Commands
CHAPTER 13 - POSITION DETERMINATION
(GPS) AT COMMANDS
These AT commands are supported on gpsOne equipped CDMA modems. GpsOne is a wireless-assisted
hybrid solution that utilizes both GPS and base-station trilateration to determine the mobile positions in more
covered situations other than GPS alone.
The following includes several set-up commands (+WPDST, +WPDOM, +WPDDD, +WPDFR, +WPDPL), the
start-session command (+WPDSS), the end-session command (+WPDES), and responses. Setup
commands are not required in most cases (as defaults will be provided) before the start-session commands.
Note that these commands are preliminary. Changes may be made when carrier plans for location services
are more readily available.
Position Determination Session Type +WPDST
Description: This command sets and returns the PD session type.
Values:
<type>
0: session to provide the last position info available
1: session to provide single-shot fix
2: tracking mode independent fixes – session to provide continuous independent
position fixes
3: tracking mode – session to provide continuous position fixes
4: data download – session to download ephemeris/almanac data only to minimize
delays to obtain future fixes
Note that when a tracking mode is requested (continuous position fixes) and the TCP/IP
transport layer is used, the position fixes will not be retrieved until the data call ends. Only
the last 10 position fixes will be presented.
Syntax:
Command syntax: AT+WPDST=<type>
Command
Possible Responses
AT+WPDST?
+WPDST: 0
Note: Request current setting type
OK
AT+WPDST=0
OK
Note: select the last position info available
AT+WPDST=9
+CME ERROR: tbd (PD session already active)
+CME ERROR: tbd (invalid PD parameter)
Note that these 2 errors can happen on all +WPD requests below, and may not be listed.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 – Position Determination (GPS) AT Commands
Position Determination Operating Mode +WPDOM
Description: This command sets and returns the PD session operating mode.
Values:
<mode>
0: Standalone only (currently not available)
1: Network only
2: Speed optimal (minimize time-to-fix, MS-based first, PDE-based later if failed)
3: Accuracy optimal (PDE preferred, MS in case of failure)
4: Data optimal– minimize data exchanged
5: MS-based only
Syntax:
Command syntax: AT+WPDOM=<mode>
Command
Possible Responses
+WPDOM: 5
OK
AT+WPDOM?
Note: Request current setting mode
AT+WPDOM=1
AT+WPDOM=0
OK
+CME ERROR: tbd (PD parameter not supported)
Position Determination Data Download +WPDDD
Description: This command specifies and returns the PD data download setting.
Note: The default for +WPDDD is zeros. User must set the appropriate parameters prior to
starting a gpsOne session.
Values:
Syntax:
<type>
0: single-shot download of data valid for the specified duration periodically download
data for the specified duration
<duration>
Specified in terms of minutes; type is declared as a word.
Note: The download duration is not currently used in the gpsOne software.
Command syntax: AT+WPDDD=<type>,<duration>
Command
Possible Responses
AT+WPDDD?
+WPDDD: 0,10
Note: Request current setting type
OK
AT+WPDDD=0,10
OK
Note: single-shot data valid for 10 minutes
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 – Position Determination (GPS) AT Commands
Position Determination Fix Rate +WPDFR
Description: This command specifies and returns the PD fix rate setting. This is used in Tracking
sessions only.
Note: The default for +WPDFR is zeros. The user must set the appropriate parameters prior
to starting a gpsOne session.
Values:
Syntax:
<num>
Number of fixes. The type <num> is a double word.
<time>
Time between fixes in milliseconds, limited to 1800 seconds.
Command syntax: AT+WPDFR=<num>,<time>
Command
Possible responses
AT+WPDFR?
+WPDFR: 10,100
Note: Request current setting type
OK
AT+WPDFR=10,100
OK
Note: maximum 10 fixes with 100
seconds in between fixes
Position Determination Privacy Level +WPDPL
Description: This command specifies and returns the PD privacy setting (this is per PD session).
Values:
<level>
0: least privacy (no restriction)
1: medium
2: highest
Syntax:
Command syntax: AT+WPDPL=<level>
Command
Possible Responses
AT+WPDPL?
+WPDPL: 0
Note: Request current setting type
OK
AT+WPDPL=2
OK
Note: Select highest level of security
Position Determination NV Privacy Level +WPPRV
Description: This command specifies and returns the NV Privacy level for gpsOne. If the value is set to 0,
then MS will answer location requests. If the value is set to 1, then the mobile will only
answer to location requests in emergency mode. The new value is committed to NV.
Values:
Syntax:
<level>
0: Allow all
1: Emergency only
Command syntax: AT+WPPRV=<level>
Command
Possible Responses
AT+WPPRV?
+WPPRV: 0
Note: Request current setting type
OK
AT+WPPRV=1
OK
Note: Phone will respond to emergency location requests only.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 – Position Determination (GPS) AT Commands
Position Determination Transport Setting +WPTLM
Description: This command specifies and returns the transport layer setting of the PD session.
Values:
<setting>
0: TCP/IP
1: DBM (Data Burse Message)
Syntax:
Command syntax: AT+WPTLM=<setting>
Command
Possible Responses
AT+WPTLM?
+WPTLM: 1
Note: Request current setting type
OK
AT+WPTLM=0
OK
Note: Sets the transport setting to TCP/IP
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 – Position Determination (GPS) AT Commands
Position Determination Start Session +WPDSS
Description: This command starts the PD session to get position. Resulting data will come in as
unsolicited responses.
Values:
<service>
“P” Position only
“PV” Position and Velocity
“PH” Position and Height
“PVH” Position, Velocity, and Height
<performance>
0: no time allowed for GPS search, use AFLT only.
1-255: upper bound of GPS search time in seconds, with 255 seconds the maximum
<accuracy>
Accuracy threshold in meters, used by MS-based only. If position uncertainty higher
than the threshold, PDE-calculated fixes will be try. The input can be between 1 to 255.
But, the reasonable range may be much smaller.
Syntax:
Command syntax: AT+WPDSS=<service>,<performance>,<accuracy>
Command
Possible Responses
AT+WPDSS=”PH”
OK
Note: Start session for position and height
with no limit on GSP search time
AT+WPDSS=”PVH”,20,50
Note: Start session for position, velocity,
and height – requiring GSP search time
limited within 20 seconds, and aim for
accuracy within 50 meters
AT+WPDSS?
+CME: ERROR: tbd (PD session already active)
+CME: ERROR: tbd (modem offline)
OK
+CMD: ERROR: tbd (tracking mode only)
+CMD: ERROR: tbd (tracking mode requires
+WPDFR setup)
+CME: ERROR: tbd (MS-based session only)
+WPDSS=”PV” (“PV” session in progress)
OK
+WPDSS=”PH”,20,50 (said session in progress)
OK (no active PD session)
Position Determination End Session +WPDES
Description: This command ends the PD session to get position.
Syntax:
Command syntax: AT+WPDES
Command
Possible Responses
AT+WPDES
Note: End session
OK
+CME: ERROR: tbd (no active session)
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 – Position Determination (GPS) AT Commands
Position Determination Start Session Result +WPDSS
Description: This unsolicited command returns the position determination data.
Values:
<lat> & <lon>
32-bit integer
<time>
64-bit integer
<fix>
2: 2D fix
3: 3D fix
<mask>
bit 0: altitude valid
bit 1: heading valid
bit 2: velocity valid (e.g. 6 means heading and velocity valid)
<altitude>
16 bit integer
<altitude uncertainty>
byte
<heading>
16 bit unsigned integer
<heading uncertainty>
byte
<velocity horizontal>
16 bit unsigned integer
<velocity vertical>
8 bit signed integer
<velocity uncertainty>
byte
Syntax:
Response Syntax: +WPDSS: <lat>,<lon>,<time>,<uncertainty>,<fix>,<mask>,<alt>,<alt_u>,
<heading>,<ang_u>,<vh>,<vv>,<v_u>
Command
Possible Responses
AT+WPDSS=”P”
OK
Note: Ask for position only.
+WPDSS:#,#,#,#,2
Note: Unsolicited result with position only.
AT+WPDSS=”PV”
OK
Note: Ask for position and velocity.
+WPDSS:#,#,#,#,2,6,#,#,#,#,#
Note: Unsolicited result with heading and velocity.
AT+WPDSS=”PH”
OK
Note: Ask for position and height.
+WPDSS:#,#,#,#,3,3,#,#,#,#,#
Note: Unsolicited result with altitude and heading.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 13 – Position Determination (GPS) AT Commands
Set IP Address of gpsOne Session +WPDIP
Description: This command allows the user to set the IP address of the gpsOne session if the TCP/IP
transport layer is used.
Values:
<ip_address>
Specified in format xxx.xxx.xxx.xxx where xxx is 000 to 255.
Syntax:
Command syntax: AT+WPDIP=<ip_address>
Command
Possible Responses
AT+WPDIP?
+WPDIP:192.168.135.124
Note: Query current gpsOne IP.
OK
AT+WPDIP=192.168.135.124
OK
Note: New gpsOne IP set.
Set Port of gpsOne Session +WPDPT
Description: This command allows the user to set the port value for the gpsOne session if the TCP/IP
transport layer is used.
Values:
Syntax:
<port>
Value is carrier specific.
Command syntax: AT+WPDIP=<port>
Command
Possible Responses
AT+WPDPT?
+WPDPT: 4911
OK
Note: Query current
gpsOne port value.
AT+WPDPT=4911
OK
Note: New gpsOne port value set.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
CHAPTER 14 - SPECIFIC AT COMMANDS
Manufacturer Identification +WGMI
Description: This command gives the manufacturer identification.
Syntax:
Command syntax: AT+WGMI
Command
AT+WGMI
Possible Responses
+WGMI: MODEM
OK
Note: Get manufacturer identification
Note: Command valid, modem
Request Model Identification +WGMM
Description: This command is used to get the supported frequency bands. With multi-band products the
response may be a combination of different bands.
Syntax:
Command syntax: AT+WGMM
Command
Possible Responses
AT+WGMM
+WGMM: 800 1900
Note: Get supported bands
OK
Note: CDMA 800 MHz band and 1900 (PCS)
Cell Environment and RxLev Indication +CCED
Description: This command can be used by the application to retrieve information about the main cell and
up to six neighboring cells. This is an extended command that may be used in two different
settings:
1. Interrogation of the cell environment information
2. Interrogation of the received signal strength indication (RSSI)
The +CCED command supports two modes of operation: on request by the application or
automatically by the product every 5 seconds.
Values:
<mode>
0: Requests a single snapshot of cell data
1: Start automatic snapshot mode
2: Stop automatic snapshot mode
Automatic snapshot mode will not return a terminating “OK”. The unsolicited responses
+CCED and/or +CSQ will be used to return the requested information.
<requested dump>
1: Main Cell: <band class>, <Channel #>, SID, NID, <Base Station P Rev>, [<Pilot PN
offset>], <Base Station ID>, [<Slot cycle index>], [<Ec/Io>], <Rx power>, <Tx power>,
<Tx Adj>
2: Neighbor1 to Neighbor20 (max): The first value is the <number of neighbor entries> in
the response. Each neighbor entry consists of the following values: <band class>, [<Pilot
PN>], <Frequency Assignment>
4: Timing Advance: Always zero for CDMA
8: Main cell RSSI indication (RxLev) from 0 to 31.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Syntax:
Command syntax: AT+CCED=<mode>[, <requested dump>]
Command
Possible Responses
+CCED: (0-2),(1-15)
OK
AT+CCED=?
AT+CCED?
+CCED: 0,13
OK
AT+CCED=0
+CSQ: 15, 99
Note: one time, dump
default (8, 4, and 1)
AT+CCED=0,1
Note: one time, dump main
cell
+CCED: 0,0,1,125,4,65535,6,,0,,,-107,-32,-63
OK
+CCED: 1,725,4,65535,6,,0,,,-104,-35,-63
OK
AT+CCED=1,8
+CSQ: 18, 99
Note: Start automatic
snapshots and dump <rssi>.
AT+CCED=2,8
Note: No OK response. New +CSQ response output every 5 seconds.
OK
Note: Stop automatic snapshots of <rssi>.
AT+CCED=0,2
+CCED:18,0,268,384,0,272,384,0,296,384,0,8,384,0,48,384,0,248,384,0
,164,384,0,16,384,0,12,384,0,224,384,0,108,384,0,476,384,0,472,384,0,
76,384,0,292,384,0,300,384,0,312,384,0,308,384
OK
Note: 18 neighbor cells are present. The first neighbor cell band class is
0, its PilotPN is 268, and its frequency assignment is 384.
Note: one time, dump
neighbor cells. Neighbor
cells must be dumped
separately.
The value displayed for Ec/Io is the index of the Active set in 0.5dB steps from 0 (0dB) to 63 (-31.5dB). For
example: 0 = 0dB, 1 = 0.5dB, 2 = 1dB, … 62 = 31dB, 63 = 31.5dB
If the <requested dump> parameter is not specified, the <requested dump> value from the previous +CCED
command will be used. If no previous +CCED <requested dump> value is available, a default value of 13 (8,
4, and 1) will be used.
For <requested dump> 4, 2, and 1, the requested information is output using the unsolicited +CCED
response. Place holders are used in the +CCED output for fields that cannot be measured or are not
meaningful in the current mode of operation. In this case, consecutive commas will be present in the output.
There are also several optional parameters ([]) that are not displayed in AMPS mode and will result in place
holders in the +CCED command output. Automatic snapshots of these dumps are not supported during
communication or registration.
For <requested dump> 8, the information is output using the unsolicited +CSQ response. The 07.07 format
of the +CSQ response is respected. However, the <fer> portion of the +CSQ response is not evaluated by
this dump request so the <fer> value will always be 99. Automatic snapshots are supported in idle mode and
during communication.
The combination of multiple <requested dump> values (addition of the values) in a single +CCED command
is supported with the exception of <requested dump> 2. The <requested dump> 2 value must be use by
itself and not in combination with other dump request values.
Either or both the +CCED and +CSQ responses are used for output depending upon the <requested dump>
value. Activation or deactivation of a +CCED response flow will not affect an existing +CSQ response flow.
Likewise, activation or deactivation of a +CSQ response flow will not affect an existing +CCED response
flow.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Analog Digital Converters Measurements +ADC
Description: This command returns the current raw value of the specified ADC data item. Two external
and four internal items can be queried.
VBATT
THERM
HDET
Battery voltage (+Vbatt) being supplied to the Modem.
Thermistor level (internal temperature) of the Modem.
Internal test use only.
ADC_0
ADC_1
External general-purpose user defined input (pin 33).
External general-purpose user defined input (pin 38).
ADC_CHG_MON Battery charger monitor (CHG_IN).
Values:
<item>
0: VBATT: 0 to 2.5 volts. Returned value = (+V_BAT*256)/(2.5*2.5) Range: 0-255
1: THERM: 100 °C (68) to –40 °C (240). Returned value = (vt*256)/2.5 vt = -0.012*T +
1.864 “T” is thermistor temperature in °Celsius. Range: 68-240 or
-1.2288 °C per step.
2: HDET: Internal use. Value range: 0-255
3: ADC_0: 0 to 2.5 volts. Value = (Vadc*256)/2.5 Value range: 0-255
4: ADC_1: 0 to 2.5 volts. Value = (Vadc*256)/2.5 Value range: 0-255
5: ADC_CHG_MON: 0 to 4.2 volts. Value = (CHG_IN*256)/4.2 Value range: 0-255
Syntax:
Command syntax: AT+ADC=<item>
Command
Possible Responses
AT+ADC=0
+ADC: 211
Note: Select VBATT
OK
Note: raw value for VBATT (~2.29 volts)
AT+ADC=1
+ADC: 94
Note: Select THERM
OK
Note: raw thermistor temperature (~34 ° C)
AT+ADC=?
+ADC: (0-5)
Note: Ask for the list of possible
values
Note: possible values 0 –5
AT+ADC?
+ADC: 1
Note: Ask for the current item
selected
OK
Note: THERM selected
Mobile Equipment Event Reporting +CMER
Description: This command enables or disables the sending of unsolicited result codes in the case of a
key press.
Values:
Syntax:
<keyp> (keypad) :
0: No keypad event reporting.
1: Keypad events are reporting using the unsolicited response: +CKEV: <key>, <press>.
See Chapter 3, Key Press or Release, for more information on +CKEV.
Command syntax: AT+CMER=<keyp>
Command
Possible Responses
AT+CMER?
+CMER: 0
Note: Display current setting.
OK
Note: Keypad event reporting disabled.
AT+CMER=1
OK
Note: Enable keypad event reporting.
Note: Keypad event reporting enabled.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Read GPIO Value +WIOR
Description: Set the I/O port as an input and read the I/O pin value.
Values:
<index>
The GPIO to read. (0-47)
<value>
Value of the GPIO pin.
Syntax:
Command syntax: AT+WIOR=<index>
Response syntax: +WIOR: <value>
Command
Possible Responses
+WIOR: 0
AT+WIOR=32
Read GPIO 32 value
OK
GPIO 32 value is 0
Write GPIO Value +WIOW
Description: Set the I/O port as an output and set the requested I/O pin value. Valid writeable GPIOs for
23xx are: 2, 3, 4, 5, 7, 8, 9, 10, 11, 13, 14, 16, 20, 21, 22, 23, 30, 36, 40, 42, 43, 44, 45, 46, 47.
Values:
<index>
The GPIO to write.
<value>
0: I/O bit is set to 0.
1: I/O bit is set to 1.
The GPIO values for 24xx are: 2, 3, 4, 5, 6, 11, 15, 16, 17, 18, 19, 37, 41, 42, 44, 48, 49, 50,
54, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 66.
Syntax:
Command syntax: AT+WIOW=<index>,<value>
Command
Possible Responses
AT+WIOW=47,1
Set GPIO 47 to 1
OK
GPIO value is written
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Play Tone +WTONE
Description: This specific command allows a tone to be played on the current speaker or on the buzzer.
Frequency, volume and duration can be set.
Values:
<mode>
0: Stop playing.
1: Play a tone
<dest>: This parameter sets the destination (mandatory if <mode>=1)
1: Speaker
2: Buzzer
<freq>: This parameter sets tone frequency (in Hz) (mandatory if <mode>=1). The range is
between 1 and 4000Hz. However, for handset and a person to hear, the effective range may
be 150-4000Hz.
<volume>(0-3): This parameter sets the tone volume. The default value is 1. Values are the
same as +CRSL.
<duration> (0-50): This parameter sets tone duration (unit of 100 ms). When this parameter
is equal to 0 (default value), the duration is infinite, and the tone can be stopped by
AT+WTONE=0.
Syntax:
Command syntax: AT+WTONE=<mode>[,<dest>,<freq>,<volume>,<duration>]
Command
Possible Responses
AT+WTONE=1,1,300,2,50
Note: Play a tone
AT+WTONE?
OK
Note: Done
+WTONE: 1,1,300,2,50
Note: Current value
OK
AT+WTONE=0
OK
Note: Stop playing
AT+WTONE=?
Note: Done
+WTONE: (0-1),(1-2),(1-4000),(0-3),(0-50)
Note: Test command
OK
Note: Done
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Play DTMF Tone +WDTMF
Description: This specific command allows a DTMF tone to be played on the current speaker. DTMF,
volume and duration can be set. This command is only used to play a DTMF tone. To send a
DTMF over the CDMA network, use the +VTS command.
Values:
<mode>
0: Stop playing.
1: Play a DTMF tone
<dtmf>: This parameter sets the DTMF to play in {0-9,*,#,A,B,C,D} (mandatory if
<mode>=1)
<volume> (0-3): This parameter sets tone gain. The values are identical to those of the
+WTONE (speaker) command (mandatory if <mode>=1).
<duration> (0-50): This parameter sets the tone duration (unit of 100 ms). When this
parameter is 0 (default value), the duration is infinite, and the DTMF tone can be stopped by
AT+WDTMF=0.
Syntax:
Command syntax: AT+WDTMF=<mode>[,<dtmf>,<volume>,<duration>]
Command
Possible Responses
AT+WDTMF=1,”*”,2,10
Note: Play a DTMF tone
AT+WDTMF?
OK
Note: Done
+WDTMF: 1,”*”,2,10
Note:
Note: Current value
AT+WDTMF=0
OK
Note: Stop playing
AT+WDTMF=?
Note: Done
ERROR
Note: Test command
Note: Done
Hardware Version +WHWV
Description: This command displays the MSM version along with hardware version number.
MSM version display format: Major.Minor; e.g. 240.16
Major:
Minor:
240 denotes MSM
1 denotes 5105; 06 denotes typeout version 6;
8 denotes 6050; 02 denotes typeout version 2;
The three-digit production hardware version is written to the modem during manufacturing.
First digit represents PCB version (ex: 5. as in V5). The second and third digits represent
last two digits of part-list number (ex. 04). In this case the hardware version number will be
504.
If the hardware version has not been written by manufacturing second filed of this command
will be 0.
Syntax:
Command syntax: AT+WHWV
Command
Possible Responses
AT+WHWV
+WHWV: 240.16,504
Note: Request MSM Version
OK
Note: MSM version is 240.16 (5105 chipset), PCB version is 5 and
parts-list used during manufacture is 04.
+WHWV: 240.82,0
AT+WHWV
Note: Request MSM Version
OK
Note: MSM version is 240.82 (6050 chipset), hardware version is 0
since manufacturing has not written the production number yet.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Select Voice Gain +WSVG
Description: The product has 2 voice gain paths. This command provides a means for selecting the
desired voice path.
Values:
Syntax:
<n> Path
0: HANDSET (Default)
1: HEADSET
Command syntax: AT+WSVG=<n>
Command
AT+WSVG=0
Possible Responses
OK
Note: Select Path 1 (Default)
Note: Path 1 selected
AT+WSVG=1
OK
Note: Select Path 2
AT+WSVG=?
Note: Path 2 selected
+WSVG: (0-1)
Note: Get the list of possible
values
Note: possible values 0 or 1
AT+WSVG?
+WSVG: 1
Note: Get the current value
Note: Path 1 is selected
Status Request +WSTR
Description: This command returns additional information for the initialization sequence and network
status.
Values:
If <status> is 1 (initialization sequence), then:
<value>
0: Not started
1: On going
2: Finished
If <status> is 2 (Network status), then:
<value>
0: No network
1: Network available
Syntax:
Command syntax: AT+WSTR=<status>
Response syntax: +WSTR: <status>,<value>
Command
Possible Responses
+WSTR: 1,2
AT+WSTR=1
Note: Select the status 1 (INIT SEQUENCE)
OK
Note: Init finished
AT+WSTR=2
+WSTR: 2,1
Note: Select the status 2 (NETWORK STATUS)
OK
Note: The network is available
AT+WSTR=?
+WSTR: (1-2)
Note: Ask the list of possible values
Note: possible values : 1, 2
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Ring Indicator Mode +WRIM
Description: This specific command sets or returns the state of the Ring Indicator Mode. In pulse RI
mode, an electrical pulse lasting approximately 10µs is sent on the Ring Indicator signal just
before sending any unsolicited AT response in order not to lose AT responses when client
tasks are in sleep state. Still in RI mode, when receiving incoming calls, electrical pulses are
sent on the RI signal.
In up-down RI mode, no pulses are sent before unsolicited AT response, and up-down
signals are sent when receiving an incoming call.
Values:
Syntax:
<n>
0: up-down RI mode
1: pulse RI mode
Command syntax: AT+WRIM=<n>
Command
Possible Responses
AT+WRIM=0
OK
Note: Select up-down RI mode
Note: up-down RI mode selected
AT+WRIM=1
OK
Note: Select pulse RI mode
AT+WRIM=?
Note: pulse RI mode selected
+WRIM: (0-1)
Note: Ask the list of possible values
OK
Note: possible values 0 or 1
AT+WRIM?
+WRIM: 1
Note: Ask the current value
OK
Note: current RI mode is pulse RI.
32kHz Sleep Mode +W32K
Description: This specific command allows the 32kHz sleep mode to be enabled or disabled. When sleep
mode is entered, the product uses a 32kHz internal clock during inactivity stages. When
enabled, sleep mode is active after 1 to 15 minutes.
Values:
<mode>
0: Disable 32kHz power down mode
1: Enable 32kHz power down mode
Syntax:
Command syntax: AT+W32K=<mode>
Command
Possible Responses
AT+W32K=1
OK
Note: Enable 32kHz sleep mode
Note: 32kHz sleep mode is enabled
AT+W32K=0
OK
Note: Disable 32kHz sleep mode
Note: 32kHz sleep mode is disabled
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Change Default Melody +WCDM
Description: This specific command allows a manufacturer specific melody to be selected. This default
melody will be played for any new incoming voice call, either on the buzzer or on the
speaker. If melody 0 is selected, no melody will be played.
Note: Selection of the player will have effect on the setting of the WCDP command.
Values:
<melody>
0: No melody (default)
1…10: Melody 1 to 10
<player>
0: Melody n°<melody> will be played on the buzzer for any new incoming voice call.
(default)
1: Melody n°<melody> will be played on the speaker for any new incoming voice call.
Syntax:
Command syntax: AT+WCDM=<melody>,<player>
Command
Possible Responses
AT+WCDM=0
OK
Note: Select no melody
AT+WCDM=5
OK
Note: Select melody n°5
AT+WCDM?
+WCDM: 5,0
Note: Indicate the current melody
OK
Note: Melody n°5 is currently selected, and the buzzer is
selected to play it.
RING
Note: An incoming call occurs, and the melody n°5 is
played on the buzzer.
AT+WCDM=,1
OK
Note: Select the speaker to play
the melody on.
AT+WCDM?
+WCDM: 5,1
OK
Note: Now the speaker is selected to play the melody if
an incoming call occurs.
Software Version +WSSW
Description: This command displays the internal software version.
Syntax:
Command syntax: AT+WSSW
Command
AT+WSSW
Possible Responses
+WSSW: WQ1.6
Note: Get Software
version
OK
Note: internal software information
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Custom Character Set +WCCS
Description: This command provides the ability to edit and display the custom character set tables. The
“CUSTOM” mode of the +CSCS command uses the custom character set tables.. In this
mode, when the user enters a string, this string is translated into the CDMA character set
using the ‘Custom To CDMA’ table. In a similar way, when the user requests a string display,
the string is translated from CDMA character set using the ‘CDMA To Custom’ table.
In edit mode, the edit session is terminated by <ctrl-Z> (0x1A), or aborted by <ESC> (0x1B).
Only hexadecimal characters (‘0’…’9’, ‘A’…’F’) can be used; two hexadecimal digits per
character. The number of characters entered must equal the edit range requested, otherwise
the command will terminate with a “+CME ERROR: 3” result.
Values:
<mode>
0: Display the table
1: Edit the table
<table>
0: Custom To CDMA conversion table
1: CDMA To Custom conversion table
<char 1>, <char 2> Character range to display/edit. If only <char 1> is present, only this
char is displayed/edited.
0…127: for CDMA To Custom conversion table
0…127: for Custom To CDMA conversion table
Syntax:
Command syntax: AT+WCCS=<mode>,<table>,<char 1>[,<char 2>]
Command
Possible Responses
AT+WCCS=0,0,20,30
Note: Display character locations 120 through 130
of the Custom To CDMA conversion table
+WCCS: 11, 78797A2020202020097E05
OK
Note: 11 characters displayed
AT+WCCS=1,0,115<CR>
20<ctrl-Z>
OK
Note: Edit successful
Note: Edit character 115 of the Custom To CDMA
conversion table
AT+WCCS=1,1,0,4<CR>
40A324A5E8<ctrl-Z>
OK
Note: Edit successful
Note: Edit the 5 first characters of the CDMA To
Custom conversion table
AT+WCCS=1,1,200
+CME ERROR: 3
Note: Edit character 200 of CDMA To Custom
conversion table
Note: Index out of range
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
CPHS Command +CPHS
Description: This command is used to activate, deactivate or interrogate a CPHS feature (e.g. Voice Mail
Indicator). When performing an interrogation (mode = 2), the selected <FctId> CPHS feature
is automatically enabled (status = 1).
Note: This command may answer +CME ERROR: 3 if the CPHS feature is disabled.
Values:
<Mode>
0: Deactivate a CPHS feature
1: Activate a CPHS feature
2: Interrogate a CPHS status
<FctId>
1: Voice Mail Indicator
<Status>
0: CPHS feature disabled
1: CPHS feature enabled
Syntax:
Command syntax: AT+CPHS=<Mode>,<FctId>
Command
Possible Responses
AT+CPHS=<Mode>,<FctId>
AT+CPHS?
OK
+CPHS: <Status>,<FctId1><CR<LF>
OK
AT+CPHS=?
Note: display the range of values
+CPHS: (0-2),(1-1)
OK
Change Default Player +WCDP
Description: This command is used to select the default destination for the melody player.
Note: Selection of the player will have effect on the setting of the WCDM command.
Values:
Syntax:
<player>
0: Speaker
1: Buzzer
Command syntax: DP = <player>
Command
Possible Responses
AT+WCDP=?
+WCDP : (0-1)
OK
AT+WCDP=0
OK
Select the speaker.
AT+WCDP?
+WCDP: 0
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Reset +WRST
Description: This command is used to reset the modem after the specified <delay> time period. The
<delay> value is entered in terms of hours and minutes.
Values:
<mode>
0: timer reset is disabled
1: timer reset is enabled
<Delay> specify the time for reset (hrs:mins)
“000:00”- “199:59”
<RemainTime> time before next reset
“000:00”- “199:59”
Syntax:
Command syntax: +WRST =<Mode>,<Delay>
Response Syntax: +WRST: <Mode>,<Delay>,<RemainTime>
Command
Possible Responses
AT+WRST=?
AT+WRST=0
ERROR
OK
Note: Disable timer
AT+WRST=1,”001:03”
Note: Enable timer and put delay at
1 hour 3 minutes
AT+WRST?
OK
+WRST: 1,”001:03”,”001:01”
OK
Note: Timer activated to reset after 1 hour and 3 minutes. Actually 1
hour and 1 minute remaining before next reset.
Set Standard Tone +WSST
Description: This command is used to set/get the sound level of the Standard Tones.
Values:
<sound level>
0: Max volume (default)
4: Min volume (muted)
Syntax:
Command syntax: AT+WSST=<sound level>
Command
AT+WSST=0
Possible Responses
OK
Note: Set volume to Max.
AT+WSST=4
OK
Note: Set the volume to Min (muted)
AT+WSST?
Note: Standard Tones are muted
+WSST: 4
Note: get current standard tones sound level
OK
Note: Current level is 4
+WSST: (0-4)
OK
AT+WSST=?
Note: Display valid parameter range.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Set Voice Privacy Level +WPRV
Description: This command requests the CDMA voice privacy level. CDMA voice privacy is an optional
feature of CDMA networks. Therefore, voice privacy will only become enabled during a voice
call if the base station supports voice privacy; otherwise this feature is unavailable on your
CDMA carrier. Thus, this command enables a request from the modem to the base station
for voice privacy. If voice privacy is activated by the base station, the unsolicited command
+WPRV:1 will appear indicating the long code PN mask for the traffic channel has been
scrambled by the base station (also see Chapter 19). This command may be issued before
or during a voice call.
Note: When voice privacy is enabled, an audible alert will be generated if the state of voice
privacy changes (loss or establishment).
Values:
Syntax:
<voice privacy level>
0: Normal (default)
1: Private
Command syntax: AT+WPRV=<voice privacy level>
Command
Possible Responses
AT+WPRV=0
OK
Note: Set to normal voice call
AT+WPRV=1
OK
Note: Request a secure voice call
OK
ATD18005551212;
+WORG:18005551212
+WCNT:3
+WPRV:1
Note: Voice Privacy is now ON
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Security PIN +WPIN
Description: This command sets, enables, or disables the security PIN. When this PIN is enabled, only
ATD (emergency numbers only), ATH, and +WPIN commands will be accepted.
Note 1: The default value of the WPIN will be the last four digits of the mobile directory
number if configured (+WMDN). If not configured, the default value of the WPIN will be
0000.
Note 2: When the security PIN is enabled, the unit will power-up in the “locked” state.
Note 3: For RUIM software builds, the default value for WPIN is '0000' even if a WMDN is
present.
Values:
<mode>
0: Disable modem lock
1: Enable modem lock
2: Change the PIN number
3: Verify the PIN. Unlock the modem until reset. Does not change NV enable/disable
setting.
4: Enable modem lock upon power up
<current val> & <new val>
0000 – 9999
Syntax:
Command syntax: AT+WPIN=<mode>,<current val>,<new val>
Command
Possible Responses
AT+WPIN=0,1111
Note: Disable the security PIN
AT+WPIN?
OK
+WPIN: 0
Note: Query the current state
OK
Note: PIN disabled
+CME ERROR: 44
Note: Invalid PIN
OK
AT+WPIN=1,2222
Note: Enable the security PIN
AT+WPIN=1,1111
Note: Enable the security PIN
AT+WPIN?
+WPIN: 1
Note: Query the current state
OK
Note: PIN enabled
AT+WPIN=2,1111,5555
Note: Change the security PIN code
from 1111 to 5555
OK
AT+CSQ?
+CME ERROR: 44
Note: Modem is locked, only ATD & +WPIN commands will be
accepted
ATD8585551212;
+CME ERROR: 44
Note: Modem is locked, only emergency numbers accepted
using ATD.
AT+WPIN=0,5555
OK
Note: Disable the security PIN
AT+WPIN=3,5555
+CME ERROR: 44
Note: Verify the security PIN
AT+WPIN=3,0000
Note: Wrong PIN value entered. Modem locked.
OK
Note: Verify the security PIN
Note: Correct PIN value entered. Modem unlocked.
AT+WPIN=4,0000
OK
Note: Power up modem lock
Note: Modem locked at power up.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Request PRL Version Information +WPRL
Description: This command requests PRL Version information for the currently selected NAM.
Syntax:
Command syntax: AT+WPRL?
Command
Possible Responses
AT+WPRL?
+WPRL: 1024
Note: Request current NAM’s PRL version
OK
AT+WPRL?
+CME ERROR: 41
Note: Request current NAM’s PRL version
Note: PRL request invalid because there’s no PRL loaded.
Note: The range for PRL is a 16-bit type.
Minute Alert +WMBP
Description: This command is used to set the minute alert while in a voice conversation.
Values:
<mode>
0: Disable alert
1: Enable alert
<interval>
1 – 30: Time in minutes
Syntax:
Command syntax: AT+WMBP=<mode>,<interval>
Command
AT+WMBP=0
Possible Responses
OK
Note: Turn off the alert
AT+WMBP=1,4
OK
Note: Turn on the alert and set 4 minutes apart
AT+WMBP?
+WMBP: 1,4
Note: Request current setting
Note: PRL request invalid because there’s no PRL
loaded.
AT+WMBP=?
+WMBP: (0-1),(1-30)
Note: Display valid parameter ranges.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Configure LED Indicator +CLED
Description: This command is used to configure GPIO 41 and GPIO 54 for general purpose use. The
default use of these two GPIO’s is to drive LED indicators on the Developer Kit board. This
command allows a user application to disable this default behavior. When disabled, the user
application has full control over the state of these GPIO’s. The modem operating software
will be prevented from change them for operational status indications.
The byte value specified with the +CLED command is a bitmap where bit 0 configures
LED1/GPIO 41 and bit 1 configures LED2/GPIO 54. Bit positions 2 through 7 are ignored.
The state of the +CLED specified control bits is not persistent. Both bit positions are always
set active (1) during boot resulting in LED status indicator operation. The +CLED command
must be used by the user application after each boot if GPIO 41 or GPIO 54 are used for
other purposes.
Values:
Syntax:
<bitmap value>
bit 0:
0 = GPIO 41 selected; 1 = LED1 selected.
0 = GPIO 54 selected; 1 = LED2 selected.
bit 1:
bit 2 – bit7: Reserved
Command syntax: AT+CLED=<bitmap value>
Command
Possible Responses
AT+CLED?
CLED: 3
Note: Display current settings.
OK
Note: Both GPIO’s are used for modem operational
status indicators.
AT+CLED=?
CLED: (0-3)
Note: Display valid parameter range.
OK
AT+CLED=1
OK
Note: Set bit 1 to inactive and bit 0 to
active.
Note: GPIO 54 available, LED1 used for modem
status.
AT+WIOW=54,0
OK
Note: Set GPIO state.
Note: Set GPIO 54 to 0.
AT+WIOR=41
+WIOR: 1
Note: Read state of LED1 indicator.
OK
Note: Read current state of LED1 indicator
AT+CLED=2
OK
Note: Set bit 1 to active and bit 0 to
inactive.
Note: LED2 used for modem status, GPIO 41
available.
AT+WIOW=41,1
OK
Note: Set GPIO state.
Note: Set GPIO 41 to 1.
AT+WIOW=54,1
OK
Note: Set LED2 state.
Note: LED2 indicator set to “on”. LED on/off state may
change due to modem status indication.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 14 – Specific AT Commands
Keypad Enable/Disable +WPAD
Description: This command is used to enable or disable the keypad functionality. When enabled, keypad
functionality supports a 5 by 5 keypad matrix of Row and Column lines. When disabled, the
GPIO’s associated with the keypad (57 through 66) are available for custom use. Refer to
the Product Technical Specification [11] for additional details.
Note: The setting established by the AT+WPAD command is not persistent unless saved to
NV by the AT&W command.
Values:
Syntax:
<mode>
0: Keypad disabled
1: Keypad enabled
Command syntax: AT+WPAD=<mode>
Command
Possible Responses
AT+WPAD=?
+WPAD (0-1)
Note: Display valid parameter range.
OK
AT+WPAD?
+WPAD: 1
Note: Display current setting.
OK
Note: Keypad enabled.
AT+WPAD=0
AT&W
OK
OK
Note: Disable keypad and write to NV.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
CHAPTER 15 - SIM TOOLKIT
Overview of SIM Application ToolKit
Summary
SIM ToolKit, also known as .SIM Application ToolKit, introduces new functionalities which open the way to a
broad range of value added services. The principle is to allow service providers the ability to develop new
applications (e.g. banking, travel, ticket booking, etc.) for subscribers and to download them into the SIM.
This solution allows new services to be accessible to the user by adding new SIM-based applications without
modifying the handset.
Functionality
SIM Toolkit refers to the functionalities described in the GSM Technical specification 11.14. It introduces
about 25 new commands for the SIM. Three classes of ToolKit functionalities have been defined with
class 1 offering a subset of commands and class 3 offering the full range of commands.
The SIM Application Toolkit supports:
• Profile Download
• Proactive SIM
• Data Download into SIM
• Menu Selection
• Call Control by SIM
Profile Download
The Profile Download instruction is sent by the customer application to the SIM as part of the
initialization. It is used to indicate which SIM Application Toolkit features the customer application
supports.
The AT command used for this operation is +STSF (SIM ToolKit Set Facilities).
Proactive SIM
A proactive SIM provides a mechanism whereby the SIM can ask the customer application to perform
certain actions.
These actions include:
• display menu
• display given text
• get user input
• send a short message
• play the requested tone
• set up a call
• provide location information
This mechanism allows SIM applications to generate powerful menu-driven sequences on the customer
application and to use services available in the network.
The commands used for this operation are:
+STIN (SIM Toolkit Indication)
+STGI (SIM Toolkit Get Information)
+STGR (SIM Toolkit Give Response)
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
Data Download to SIM
Data downloading to the SIM allows data (SMS, phonebook) or programs (Java applets) received by
SMS or by Cell Broadcast to be transferred directly to the SIM Application.
This feature does not need any AT command. It is transparent to the customer application.
Menu Selection
A set of menu items is supplied by the SIM Application ToolKit. The menu selection command can then
be used to inform the SIM Application which menu item is selected.
The commands used for this operation are:
+STIN (SIM Toolkit Indication)
+STGI (SIM Toolkit Get Information)
+STGR (SIM Toolkit Give Response)
Call control by SIM
The call control mechanism allows the SIM to check all dialed numbers, supplementary service control
strings and USSD strings before connecting to the network. This gives the SIM the ability to allow, bar or
modify the string before the operation starts.
The commands used for this operation are:
+STCR (SIM Toolkit Control Response)
+STGR (SIM Toolkit Give Response)
Messages Exchanged During a SIM ToolKit Operation
The following scheme shows the SIM Toolkit commands and unsolicited results that are exchanged.
+STSF=X,XXXXXXXX
STEP 1: Configuration and Activation
+STIN=X
STEP 2: SIM sends pro-active command
MULTI-TECH
Modem
Customer
Application
+STGI=X
+STGI response
STEP 3: Customer application gets all the information.
+STCR:X
+STGR=X,XXXXXX
STEP 4: User response is sent to the SIM.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
On the first step the customer application informs the modem which facilities are supported. This
operation is performed with the +STSF (SIM ToolKit Set Facilities) command, which is also used to
activate or deactivate the SIM Toolkit functionality. On the second step, an unsolicited result +STIN (SIM
ToolKit indication) is sent by the product to indicate the customer application which command type the
SIM Application Toolkit is running on the SIM card. The last SIM Toolkit indication can be requested by
the +STIN? command. On the third step, the customer application uses the +STGI (SIM ToolKit Get
Information) command to get all the information about the SIM ToolKit command, given by +STIN. On
the fourth step, the customer application uses the +STGR (SIM Toolkit Give Response) to send its
response (if any) to the SIM ToolKit Application.
The +STCR (SIM Toolkit Control response) indication is an unsolicited result sent by the SIM when Call
control functionality is activated and before the customer application has performed any outgoing call,
SMS, SS, or USSD.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
SIM ToolKit Set Facilities (+STSF)
Description: This command allows SIM ToolKit facilities to be activated, deactivated or configured.
Values:
<mode>
0: Deactivates the SIM Toolkit functionalities.
1: Activates the SIM Toolkit functionalities.
2: Configures the SIM Toolkit functionalities.
<Config>
(160060C01F . 5FFFFFFF7F) (hex format)
<Timeout>
1-255: Timeout for user responses (multiple of 10 seconds).
<Autoresponse>
0: Automatic response is not activated
1: Automatic response is activated
The activation or deactivation of the SIM Toolkit functionalities requires the use of the
+CFUN (Set phone functionality) command to reset the product (this operation is not
necessary if PIN is not entered yet).
The <Config> parameter gives the coding of the TERMINAL PROFILE, precisely the list of
SIM Application Toolkit facilities that are supported by the customer application.
The <Timeout> parameter (multiple of 10 seconds) sets the maximum time the user has for
reacting (to select an item, to input a text, etc).
When the <Autoresponse> is activated, the +STIN indication for Play Tone (5), Refresh (7),
Send SS (8), Send SMS (9) or Send USSD (10) is automatically followed by the
corresponding +STGI response.
Note: Some bits are related to the product only and not to the customer application. The
product automatically sets these bits to either 0 or 1 whatever the user enters with the
+STSF command.
Each facility is coded on 1 bit:
• bit = 1: facility is supported by the customer application.
• bit = 0: facility is not supported by the customer application.
Only the first five bytes of the TERMINAL PROFILE (Class 2) can be configured, the other
are set to 0. (See structure of TERMINAL PROFILE in APPENDIX C)
Syntax:
Command syntax: AT+STSF=<mode>[,<config>][,<Timeout>][,<AutoResponse>]
Command
Possible Responses
AT+STSF=<Mode>[,<Config>][,
<Timeout>][,<AutoResponse>]
AT+STSF?
OK
+CME ERROR: <err>
+STSF:
<Mode>,<Config>,<Timeout>,<Autoresponse>
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
Error Codes
+CME ERROR: 3 Operation not allowed . This error is returned when a wrong parameter is entered.
Example:
AT+CMEE=1
OK
AT+WIND=15
OK
Enable the reporting of mobile equipment errors
Set indications
AT+CPAS
+CPAS: 0
OK
Query ME Status
ME is ready.
AT+STSF=?
Test command SIM ToolKit Set Facilities
+STSF: (0-2), (160060C01F . 5FFFFFFF7F),(1-255)
OK
AT+STSF?
+STSF: 0,”160060C000”,3
OK
No activation of SIM ToolKit functionality
AT+STSF=2,”5FFFFFFF7F”
OK
AT+STSF=3
+CME ERROR: 3
AT+STSF=1
OK
Set all SIM ToolKit facilities (class 3).
Syntax Error
Activation of SIM ToolKit functionality
Reboot Software.
AT+CFUN=1
OK
AT+CPIN?
Is the ME requiring a password?
Yes, SIM PIN required
+CPIN: SIM PIN
AT+CPIN=0000
OK PIN Ok
+WIND: 4
Init phase is complete
AT+STSF?
+STSF: 1,”5FFFFFFF7F”,3
OK
SIM ToolKit functionality activated with all facilities
SIM ToolKit Indication (+STIN)
Unsolicited Result:
In order to allow the customer application to identify the pro-active command sent via SIM ToolKit, a
mechanism of unsolicited SIM ToolKit indications (+STIN) is implemented.
Syntax:
+STIN: <CmdType>
Option: <CmdType>
0:
1:
2:
3:
4:
5:
6:
7:
9:
11 :
Indicates that a .Setup Menu. Pro-active command has been sent from the SIM.
Indicates that a .Display Text. Pro-active command has been sent from the SIM.
Indicates that a .Get Inkey. Pro-active command has been sent from the SIM.
Indicates that a .Get Input. Pro-active command has been sent from the SIM.
Indicates that a .Setup Call. Pro-active command has been sent from the SIM.
Indicates that a .Play Tone. Pro-active command has been sent from the SIM. (*)
Indicates that a .Sel Item. Pro-active command has been sent from the SIM.
Indicates that a .Refresh. pro-active command has been sent from the SIM. (*)
Indicates that a .Send SMS. Pro-active command has been sent from the SIM. (*)
Indicates that a SETUP EVENT LIST. Pro-active command has been sent from the
SIM.
98 :
Indicates the timeout when no response from user.
99: Indicates that a .End Session. Has been sent from the SIM.
(*) if the automatic response parameter is activated, this indication is followed by the
corresponding +STGI response.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
Last SIM Toolkit Indication:
The last SIM toolkit indication sent by the SIM can be requested by the AT+STIN? command. This command
is only useable between the sending of the STIN indication by the SIM (Chapter 15, diagram Messages
Exchanged During an SIM ToolKit Operation) and the response of the user with the +STGI command
(Chapter 15).
Command syntax: AT+STIN?
Command
Possible Responses
AT+STIN?
+STIN: 0
Note: Ask for the last SIM toolkit
indication sent by the SIM.
OK
Note: the last SIM toolkit indication was
a Setup Menu
AT+STGI=0
OK
Note: Display the SIM toolkit application
Menu.
AT+STIN?
+CME ERROR: 4
Note: Ask for the last SIM toolkit
indication sent by the SIM.
Note: operation not supported, the
+STGI command has been already used .
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
SIM ToolKit Get Information +STGI)
Description: This command allows you to get the information (text to display, Menu information,
priorities.) of a pro-active command sent from the SIM. The information is returned only after
receiving a SIM Toolkit indication (+STIN).
Syntax:
Command syntax: +STGI=<Cmd>
Command
Possible Responses
+STGI=<Cmd>
See following table.
+CME ERROR: <err>
+STGI: (0-11)
OK
+STGI=?
Note: Display valid parameter range.
Cmd
0
Description
Get information about
‘Setup Menu’ pro-active command.
Possible Responses
+STGI: <Alpha Identifier menu>
+STGI: <Id1>,<NbItems>,<Alpha Id1 Label>,<Help
Info>[,<NextActionId>]<CR><LF>
+STGI: <Id2>,<NbItems>,<Alpha Id2 Label>,<Help
Info>[,<NextActionId>]<CR><LF>
[.]]
No action expected from SIM.
1
2
3
Get information about
+STGI: <Prior>,<Text>,<ClearMode>
No action expected from SIM.
+STGI: <Format>,<HelpInfo>[,<TextInfo>]
SIM expects key pressed (+STGR).
+STGI: <Format>,<EchoMode>,<SizeMin>,<SizeMax
<HelpInfo>[,<TextInfo>]
‘Display text’ pro-active command.
Get information about ‘Get Inkey’
pro-active command.
Get information about ‘Get
Input’ pro-active command.
SIM expects key input (+STGR).
+STGI: <Type>,<CalledNb>,<SubAddress>,<Class>
SIM expects user authorization (+STGR).
+STGI:
<ToneType>[,<TimeUnit>,<TimeInterval>,<TextInfo>]
No action.
4
5
Get information about
‘Setup call’ pro-active command.
Get information about ‘Play
Tone’ pro-active command.
6
Get information about ‘Sel
Item’ pro-active command.
+STGI: <DefaultItem>, <Alpha Identifier
menu><CR><LF>
+STGI: <Id1>,<NbItems>,<Alpha Id1 Label>,<Help
Info>[,<NextActionId>]<CR><LF>
+STGI: <Id2>,<NbItems>,<Alpha Id2 Label>,<Help
Info>[,<NextActionId>]<CR><LF>
[.]]
SIM expects an item choice (+STGR).
7
Get information about
+STGI: <RefreshType>
‘Refresh’ pro-active command.
Get information about ‘Send SS’ pro-
active command.
No action (Refresh done automatically by product).
Currently not supported
8
9
Get information about ‘Send SMS’
pro-active command.
+STGI: <TextInfo>
No action (Send SMS done automatically by product).
10
11
Get information about ‘Send
USSD’ pro-active command
Get information about
Currently not supported
+STGI: <Evt>
‘SETUP EVENT LIST’ pro-
active command.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
Values:
Values when Cmd=0 (Setup menu )
<Alpha Identifier menu> Alpha identifier of the main menu
<Idx> (1 –255)
Menu item Identifier
<NbItems> (1 –255)
<Alpha Idx Label>
<HelpInfo>
Number of items in the main menu
Alpha identifier label of items in ASCII format
0:
1:
No help information available
Help information available
<NextActionId>
Contains a pro-active command identifier.
Compared to other commands the customer application can always get information about setup
menu after having received the +STIN:0 indication.
Values when Cmd=1 (Display text )
<Prior>
0:
1:
Normal priority of display
High priority of display
<Text>
Text to display in ASCII format
<ClearMode>
0:
1:
Clear message after a delay (3 seconds)
Wait for user to clear message
Values when Cmd=2 (Get Inkey )
<Format>
0:
1:
2:
Digit (0-9, *, #,and +)
SMS alphabet defaults
UCS2
3:
Yes/No
<HelpInfo>
0:
1:
No help information available
Help information available
<TextInfo>
Text information in ASCII format
Values when Cmd=3 (Get Input )
<Format>
0:
1:
2:
3:
4:
Digit (0-9, *, #,and +)
SMS alphabet defaults
UCS2
Unpacked format
Packed format
<EchoMode>
0:
1:
Echo off
Echo on
<SizeMin> (1 –255)
<SizeMax> (1 –255)
<HelpInfo>
Minimum length of input
Maximum length of input
0:
1:
No help information available
Help information available
Text information in ASCII format
<TextInfo>
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
Values when Cmd=4 (Setup Call )
<Type>
0:
Set up call but only if not currently busy on another call
1:
2:
Set up call, putting all other calls (if any) on hold
Set up call, disconnecting all other calls (if any)
Called party number in ASCII format
<CalledNb>
<SubAdress>
<Class>
Called party sub-address in ASCII format
0:
1:
2:
Voice call
Data call
Fax call
Values when Cmd=5 (Play tone )
<ToneType>
0:
Tone Dial
1:
Tone Busy
2:
3:
4:
5:
Tone Congestion
Tone Radio ack
Tone Dropped
Tone Error
6:
7:
Tone Call waiting
Tone Ringing
8:
9:
10:
Tone General beep
Tone Positive beep
Tone Negative beep
<TimeUnit>
0:
1:
2:
Time unit used is minutes
Time unit used is seconds
Time unit used is tenths of seconds
<TimeInterval> (1 –255)
<TextInfo>
Time required expressed in units
Text information in ASCII format
Values when Cmd=6 (Sel Item )
<DefaultItem> (1 –255)
<Alpha Identifier menu>
<Idx> (1 –255)
Default Item Identifier
Alpha identifier of the main menu
Identifier items
<NbItems> (1 –255)
<Alpha Idx Label>
<HelpInfo>
Number of items in the menu
Alpha identifier label of items in ASCII format
0:
1:
No help information available
Help information available
<NextActionId>
Contains a pro-active command identifier.
Values when Cmd=7 (Refresh )
<RefreshType>
0:
1:
2:
3:
4:
SlM initialization and full file change notification
File change notification
SIM initialization and file change notification
SIM initialization
SIM reset
Values when Cmd=8 (Send SS )
<TextInfo>
Text information in ASCII format.
Text information in ASCII format.
Text information in ASCII format
Values when Cmd=9 (Send SMS )
<TextInfo>
Values when Cmd=10 (Send USSD )
<TextInfo>
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
Values when Cmd=11 (Setup Event List )
<Evt>
1:
2:
3:
4:
Reporting asked for an.Idle Screen. Event
Reporting asked for an User Activity. Event
Reporting asked for Idle Screen. And User Activity. Events
Cancellation of reporting event
Note: For the UCS2 format, texts are displayed in Hexadecimal ASCII format. For example,
when the SIM sends a Text String containing 0x00 0x41, the text displayed is .0041.
Error Codes
+ CME ERROR: 3
Operation not allowed . This error is returned when a wrong parameter is
detected.
+CME ERROR: 4
Operation not supported . This error is returned when the user wants to get
information about a SIM ToolKit pro-active command (with SIM ToolKit
functionality not activated.)
+CME ERROR: 518
SIM ToolKit indication not received . This error is returned when the SIM
Toolkit indication (+STIN) has not been received.
Example
Initially, all facilities are activated, the PIN is not required and SIM toolkit functionality is activated.
AT+CMEE=1
OK
AT+WIND=15
Enable the reporting of mobile equipment errors
Set indications
OK
AT+STSF?
+STSF: 1,”5FFFFFFF7F”,3
OK
+STIN: 0
SIM ToolKit functionality activated with all facilities.
The main menu has been sent from the SIM.
AT+STIN?
+STIN: 0
OK
AT+STGI=0
Get information about the main menu
Main menu contains 3 items.
+STGI: “SIM TOOLKIT MAIN MENU”
+STGI: 1,3,”BANK”,0
+STGI: 2,3,”QUIZ”,0
+STGI: 3,3,”WEATHER”,0
OK
AT+STIN?
+CME ERROR: 4
Unsolicited Result: SIM ToolKit Control Response (+STCR)
When the customer application makes an outgoing voice or SMS call when the call control facility is
activated, CALL CONTROL and SMS CONTROL responses can be identified. This is also applicable to SS
calls.
Response syntax: +STCR: <Result>[,<Number>,<MODestAddr>,<TextInfo>]
<Result>
0: Control response not allowed
1: Control response with modification
<Number>
Called number, Service Center Address or SS String in ASCII format
MO destination address in ASCII format
<MODestAddr>
<TextInfo>
Text information in ASCII format
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
SIM ToolKit Give Response (+STGR)
Description: This command allows the application/user to select an item in the main menu or to answer the
following proactive commands:
•
•
•
•
•
GET INKEY
GET INPUT
SELECT ITEM
SETUP CALL
DISPLAY TEXT
Key pressed by the user.
Message entered by the user.
Selected item.
User confirmation.
User confirmation to clear the message.
It is also possible to terminate the current proactive command session by sending a Terminal Response to
the SIM with the following parameters:
•
•
•
•
•
BACKWARD MOVE Process a backward move
BEYOND CAPABILITIES Command beyond ME capabilities
UNABLE TO PROCESS ME is currently unable to process command
NO RESPONSE No response from the user
END SESSION User abort.
Values:
<CmdType>
0: Item selection in the main menu
1: User confirmation to clear displayed Text.
2: Response for a ‘Get Inkey’
3: Response for a ‘Get Input’
4: Response for a ‘Setup call’
96: Response for a ‘Sel Item’
95: Backward move
96: Command beyond ME capabilities
97: ME currently unable to process command
98: No response from the user
99: User abort
Values when CmdType=0 (Select an item from the main menu)
<Result>
1: Item selected by the user
2: Help information required by user
<Data>
Contains the item identifier of the item selected by the user
Values when CmdType=1 (Confirm the display text clearing)
No values
Values when CmdType=2 (Get Inkey)
<Result>
0: Session ended by user
1: Response given by the user
2: Help information required by user
<Data>
Contains the key pressed by the user
Values when CmdType=3 (Get Input)
<Result>
0: Session ended by user
1: Response given by the user
2: Help information required by user
<Data>
Contains the string of characters entered by the user. For inputs in UCS2 format, the
data are entered in ASCII format. Example: 8000410042FFFF entered, the SIM
receives 0x00 0x41 0x00 0x42 with UCS2 DCS.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
Values when CmdType=4 (Setup call)
<Result>
0: User refuses the call
1: User accepts call
Values when CmdType=6 (Select Item)
<Result>
0: Session terminated by the user
1: Item selected by the user
2: Help information required by the user
3: Return to the back item
<Data>
Contains the item identifier selected by the user
Sending a Terminal Response to the SIM:
Values when CmdType=95 (Backward Move)
Values when CmdType=96 (Command beyond ME capabilities)
Values when CmdType=97 (ME currently unable to process command)
Values when CmdType=98 (No response from the user)
Values when CmdType=99 (SIM Toolkit Session aborting by the user)
No values. It is possible to send a Terminal Response after the +STIN indication or after
the +STGI command.
For the SETUP MENU Proactive Command, it is only possible to send a Terminal
Response after the +STIN: 0 indication, not after a +STGI=0 request. All of the Terminal
Responses are not possible with all of the Proactive Commands. If a Terminal Response
is attempted during an incompatible Proactive Command session, a +CME ERROR: 3
will be returned.
Possible Error Codes
+ CME ERROR: 3
Operation not allowed. This error is returned when a wrong parameter is
detected.
+CME ERROR: 4
Operation not supported. This error is returned when the user gives a
response with SIM ToolKit functionality not activated. Or if the SIM Toolkit
indication (+STIN) has not been received.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 15 – SIM TOOLKIT
Example
Initially, all facilities are activated, the PIN is not required and the SIM toolkit functionality is activated.
+STIN: 0
AT+STGI=0
+STGI: 1,3,”BANK”,0
+STGI: 2,3,”QUIZ”,0
+STGI: 3,3,”WEATHER”,0
OK
The main menu has been sent from the SIM.
Get information about the main menu
The main menu contains 3 items.
AT+STGR=0,1,1
OK
The item 2 of the main menu has been selected.
+STIN: 6
AT+STGI=6
+STGI: 1,”BANK”.
The Sel item menu has been sent from the SIM.
Get information about the BANK menu
The BANK menu contains two items.
+STGI: 1,2,”PERSONAL ACCOUNT ENQUIRY”,1
+STGI: 2,2,”NEWS”,0
OK
AT+STGR=6,1,1
OK
Select Item 1.
+STIN: 3
User request to enter Password sent.
Get information about this request.
Enter Account Password:”
AT+STGI=3
+STGI: 0,0,4,4,0”
OK
AT+STGR=3,1<CR>
>0000<Ctrl Z>
OK
The user enters the Password.
+STIN:1
A text info has been sent from the SIM.
Get information about this text.
Password correct, please wait for response”,0
AT+STGI=1
+STGI: 0,”
OK
+STIN: 9
AT+STGI=9
SIM requests a bank account update from bank server via the network (SEND SMS)
Get all information about the SEND SMS
+STGI:
OK
“
Send account balance of user, authorization ok”
********* After a short period of time. ********
+STIN: 5
+STGI=5
Transaction is complete: BEEP
Get information about the Tone
+STGI: 9,1,1
+STIN: 1
AT+STGI=1
+STGI: 0,”
OK
Display text indication
Your account balance is 1000 $”,0
Syntax:
Command syntax: +STGR=<CmdType>[,<Result>,<Data>]
Command
Possible Responses
+STGR=<CmdType>[,<Result>,<Data>]
OK
+CME ERROR: <err>
OK
+CME ERROR: <err>
For Get Input with <Result>=1:
+STGR=3,1<CR>
<Data><Ctrl Z>
For GetInkey with <Result>=1
+STGR=2,1<CR>
OK
+CME ERROR: <err>
<Data><Ctrl Z>
+STGR=?
OK
Note: Display valid parameter range.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 16 – Provisioning AT Commands
CHAPTER 16 - PROVISIONING AT COMMANDS
Service Programming Code +WSPC
Description: This command allows for entry of the service programming code (either MSL or OTKSL).
Upon successful entry of this code, all other service provisioning AT commands may be
used. If this code is not properly entered prior to attempting other provisioning AT
commands, all provisioning commands will return ERROR. If the OTKSL is used to enter
provisioning mode, only the +WIMI, +WMDN, and +WCMT commands will be allowed. All
other commands will return ERROR.
This command supports five attempts to enter the correct service programming code. If five
incorrect attempts are performed, the ME will power down.
Once the correct SPC code is entered, the modem transitions to the Service Programming
state. This state is not exited until a commit is done (+WCMT). While in the Service
Programming state, subsequent validations of the SPC code are ignored until the Service
Programming state is reset.
Values:
<lock type>
0: OTKSL – One Time Key Subsidy Lock
1: MSL – Master Subsidy Lock
<code>
Six character programming code.
Syntax:
Command syntax: AT+WSPC=<lock type>,<code>
Command
AT+WSPC?
Possible Responses
ERROR
Note: Service programming code request
Note: Invalid request
AT+WSPC=?
ERROR
Note: Invalid request
ERROR
AT+WSPC=1,111111
Note: Enter service programming code 111111
Note: Code invalid
AT+WSPC=1,000000
OK
Note: Enter service programming code 000000
Note: Code valid
Mobile Directory Number +WMDN
Description: This command is used to enter a new mobile directory number. Valid numbers are between
10 and 15 digits in length. For support of Wireless Number Portability, changes to the MDN
will ALWAYS update the IMSI_M portion (least significant 10 digits) of the IMSI. Changes to
the MDN will also automatically update the Access Overload Class values unless specifically
modified using the +WAOC command. The new IMSI_M and Access Overload Class values
will not be visible in the WIMI and WAOC commands until after the changes are committed
with the WCMT command.
Syntax:
Command syntax: AT+WMDN=<number>
Command
Possible Responses
AT+WMDN?
+WMDN: 8581111111
Note: Get current mobile directory number
OK
AT+WMDN=8585551212
OK
Note: Set mobile directory number to 8585551212
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 16 – Provisioning AT Commands
Set IMSI +WIMI
Description: This command is used to set the IMSI. Valid IMSI is 15 digits in length. For support of
Wireless Number Portability, changes to the IMSI will NOT update the MDN. Changes to the
IMSI will automatically update the Access Overload Class values unless specifically modified
using +WAOC command.
Syntax:
Command syntax: AT+WIMI=<number>
Command
AT+WIMI?
Possible Responses
+WIMI: 310008581111111
OK
Note: Get current IMSI
AT+WIMI=310008585551212
OK
Note: Set IMSI to 310008585551212
SID and NID +WSID
Description: This command is used to set the home SID and NID for 800Mhz CDMA operation only. The
new SID/NID values are committed to NV with the +WCMT command.
Values:
<index>
The location in the SID/NID list to store the values. A maximum of 20 entries (0-19) are
supported.
<SID number>
SID value range – 0 to 32767.
<NID number>
NID value range – 0 to 65535.
Syntax:
Command syntax: AT+ WSID=<index>,<SID number>,<NID number>
Command
Possible Responses
AT+WSID?
+WSID: 1, 45, 84
Note: Get current SID and NID
OK
Note: The SID/NID pair 45,84 in location 1 is
selected.
AT+WSID=3, 4145, 2102
OK
AT+WSID?
+WSID: 3, 4145, 2102
Note: Set SID to 4145 and NID to 2102.
Store in location 3 of the SID/NID list.
OK
Note: The SID/NID pair 4145,2102 in location 3 is
selected.
AT+WSID=2
OK
AT+WSID?
+WSID: 2, 0, 0
Note: Set SID to 0 and NID to 0. Store in
location 2 of the SID/NID list.
AT+WSID=4, 64
OK
Note: The SID/NID pair 0,0 in location 2 is selected.
OK
AT+WSID?
+WSID: 4, 64, 0
Note: Set SID to 64 and NID to 0. Store
in location 4 of the SID/NID list.
OK
Note: The SID/NID pair 64,0 in location 4 is
selected.
AT+WSID=, 64, 1024
OK
AT+WSID?
+WSID: 4, 64, 1024
Note: Set SID to 64 and NID to 1024.
Store in the currently selected location of
the SID/NID list.
OK
Note: The SID/NID pair 64,1024 in location 4 is
selected.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 16 – Provisioning AT Commands
Access Overload Class +WAOC
Description: This command is used to set the Access Overload Class.
Values:
Syntax:
<number>
Access overload value range – 0 to 15.
Command syntax: AT+WAOC=<number>
Command
Possible Responses
AT+WAOC?
Note: Get current Access Overload Class
+WAOC: 5
OK
AT+WAOC=7
OK
Note: Set Access Overload Class to 7
Slot Cycle Index +WSCI
Description: This command is used to set the slot cycle index.
Values:
Syntax:
<number>
Slot cycle index, ranges from 0 to 7.
Command syntax: AT+WSCI=<number>
Command
Possible Responses
AT+WSCI?
Note: Read the current slot cycle index
+WSCI: 2
OK
AT+WSCI=1
OK
Note: Set the slot cycle index
Primary Browser Gateway +WBGP
Description: This command is used to set the primary browser gateway IP address (Ipv4). If a browser is
not natively supported by the modem, this command will return ERROR.
Values:
Syntax:
<num>
0-255
Command syntax: AT+WBGP=<num>,<num>,<num>,<num>
Command
Possible Responses
AT+WBGP?
+WBGP: 127,0,0,1
Note: Get current gateway
AT+WBGP=255,255,255,0
Note: Set primary gateway to 255.255.255.0
OK
OK
Secondary Browser Gateway +WBGS
Description: This command is used to set the secondary browser gateway IP address (Ipv4). If a browser
is not natively supported by the modem, this command will return ERROR.
Values:
Syntax:
<num>
0-255
Command syntax: AT+WBGS=< num >,< num >,< num >,< num >
Command
Possible Responses
AT+WBGS?
+WBGS: 127,0,0,1
Note: Get current primary gateway
AT+WBGS=255,21,255,0
Note: Set secondary gateway to 255.21.255.0
OK
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 16 – Provisioning AT Commands
Packet Dial String +WPDS
Description: This command is used to set the packet dial string.
Values:
Syntax:
<string>
A string of length 0 to 16 characters.
Command syntax: AT+WPDS=<string>
Command
Possible Responses
AT+WPDS?
+WPDS: ”#777”
OK
Note: Get current Packet Dial String
AT+WPDS=”#999”
Note: Current Packet Dial String is #777
OK
Note: Set the Packet Dial String to #999
Primary CDMA Channels +WPCC
Description: This command is used to set the primary CDMA channels for 800Mhz CDMA operation only.
Values entered must be valid CDMA 800Mhz Channel numbers.
Values:
Syntax:
<channel a number>
Value range: 0 – 2047
<channel b number>
Value range: 0 – 2047
Command syntax: AT+WPCC=<channel a number>,<channel b number>
Command
Possible Responses
AT+WPCC?
+WPCC: 283,384
Note: Get current primary CDMA channels
OK
AT+WPCC=211,432
OK
Note: Set the primary CDMA channels
Secondary CDMA Channels +WSCC
Description: This command is used to set the secondary CDMA channels for 800Mhz CDMA operation
only. Values entered must be valid CDMA 800Mhz Channel numbers.
Values:
Syntax:
<channel a number>
Value range: 0 – 2047
<channel b number>
Value range: 0 – 2047
Command syntax: AT+WSCC=<channel a number>,<channel b number>
Command
Possible responses
AT+WSCC?
+WPCC: 691,777
Note: Get current secondary CDMA channels
OK
AT+WPCC=511,632
OK
Note: Set the secondary CDMA channels
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 16 – Provisioning AT Commands
Service Option Management +WSOM
Description: This command is used to manage Service Options for EVRC. It will allow the user to enable
EVRC, set home page, home origination, and roam origination voice service options for the
current NAM. It is only available for software builds, which include EVRC Service Option
Management feature.
Values:
<enable>
0: disable EVRC
1: enable EVRC
<home page SO>
0: IS96A
1: EVRC
2: 13k
3: IS96
4: WILDCARD
<home orig SO> & <roam orig SO>
0: IS96A
1: EVRC
2: 13k
3: IS96
Syntax:
Command syntax: AT+WSOM=<enable>,<home page SO>,<home orig SO>,<roam orig
SO>
Command
Possible Responses
AT+WSOM?
+WSOM: 0, 1, 2, 0
Note: Get the Service
Options of the current NAM
OK
Note: EVRC disabled, home page is set to EVRC, home orig is set to
13k, roam orig is set to IS96A
AT+WSOM=1,4,2,2
Note: Set current NAM
Service Options
OK
Note: EVRC enabled, set home page to WILDCARD, set home orig to
13k, set roam orig to 13k
Commit Changes +WCMT
Description: This command is used to commit or to undo/revert any changes done during the service
programming session. Changes performed during this session will not take place until a
commit command has been sent (AT+WCMT=1). Commission of these changes will force a
software reset of the modem. Sending this command indicates this service provisioning
session is complete. In order to perform any subsequent provisioning, the service
programming code must be entered using the +WSPC command.
Values:
<val>
0: undo changes
1: commit changes
Syntax:
Command syntax: AT+WCMT=<val>
Command
Possible Responses
OK
AT+WCMT=0
Note: Undo any changes performed during this provisioning AT
session
AT+WCMT=1
OK
Note: Commit all changes performed during this provisioning AT
session to non-volatile memory.
Note: software reset is performed
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 16 – Provisioning AT Commands
Read SID/NID Entries +WSNR
Description: This command is used to read the current SID/NID list entries. The displayed entry will
always be the current value; including those changes made with the +WSID command prior
to being committed to NV with the +WCMT command.
Values:
Syntax:
<index>
0-19: Location in SID/NID list to read.
Command syntax: AT+WSNR=<index>
Command
Possible Responses
AT+WSNR=5
ERROR
Note: Display entry 5 of SID/NID list.
AT+WSPC=1,000000
AT+WSNR=5
Note: Service provisioning code not yet entered.
OK
Note: Service code successfully entered.
Note: Display entry 5 of SID/NID list.
+WSNR: 5, 123, 65535
OK
Note: Entry 5 of SID/NID list contains 123,65535.
AT+WSNR?
Note: Show last read SID/NID list
index. Default: 0.
+WSNR: 5
OK
AT+WSNR=?
Note: Show SID/NID list index
range.
+WSNR: (0-19)
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 16 – Provisioning AT Commands
Service Programming Example
Command
Response
ERROR
AT+WBGP=255,255,255,255
Note: Attempt to set the primary browser gateway
AT+WPDS?
Note: Service Programming code not yet entered
ERROR
Note: Get current Packet Dial String
Note: Service Programming code not yet entered
AT+WSPC=1,000000
OK
Note: Enter service programming code
AT+WPDS?
Note: Service Programming code entered properly
+WPDS: ”#777”
Note: Get current Packet Dial String
OK
Note: Current Packet Dial String is #777
AT+WPDS=”#999”
OK
Note: Set the Packet Dial String to #999
AT+WCMT=1
OK
Note: Commit all changes performed during this
provisioning AT session to non-volatile memory.
AT+WSPC=1,000111
Note: software reset is performed
ERROR
Note: Enter service programming code
Note: Service Programming code incorrect
AT+WSPC=1,000000
OK
Note: Enter service programming code
AT+WPDS?
Note: Service Programming code entered properly
+WPDS: ”#999”
OK
Note: Get current Packet Dial String
AT+WPDS=”#555”
Note: Current Packet Dial String is #999
OK
Note: Set the Packet Dial String to #555
AT+WSCI?
Note: Read the current slot cycle index
AT+WSCI=1
+WSCI: 2
OK
OK
Note: Set the slot cycle index
AT+WCMT=0
OK
Note: Undo any changes performed during this
provisioning AT session.
Note: No software reset since this is an undo
command.
AT+WSPC=1,000000
OK
Note: Enter service programming code
Note: Service Programming code entered properly
AT+WPDS?
+WPDS=”#999”
Note: Get current Packet Dial String
OK
Note: Current Packet Dial String is #999 (changes not
committed from last write)
AT+WSCI?
+WSCI: 2
Note: Read the current slot cycle index
OK
Note: Slot cycle index is 2 (changes not committed
from last write)
AT+WMDN=8585551212
OK
Note: Set mobile directory number to 8585551212
AT+WCMT=1
OK
Note: Commit all changes performed during this
provisioning AT session to non-volatile memory.
Note: software reset is performed
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
CHAPTER 17 - EXTENDED AT COMMANDS IN IS707.3
Multi-Tech CDMA modem also implements the CDMA AT commands as specified in the TIA/EIA/IS-707.3.
Refer to IS707.3 for more information on these commands (range, parameter definition, result codes, etc.).
Note: Some of the AT commands may not be supported by the network. Please verify with the carrier on the
supported IS707.3 commands.
Remote Async/Fax Command X
Description: This command sends a CONNECT message when a connection is established by blind
dialing and enables the additional result codes.
Syntax:
Command syntax: ATX<n>
Command
Possible Responses
ATX0
OK
Note: Ignores dial tone and busy signal.
Note: Command is valid
ATX1
OK
Note: Disable dial tone and busy detection.
Note: Command is valid
ATX2
OK
Note: Disable busy detection & enable dial tone detection.
Note: Command is valid
ATX3
OK
Note: Enable busy detection & disable dial tone detection.
ATX4
Note: Command is valid
OK
Note: Enable busy and dial tone detection.
Note: Command is valid
Reset to Default Configuration Z0
Description: This command is used to reset to the default configuration.
Syntax:
Command syntax: ATZ0
Command
Possible Responses
ATZ0
OK
Note: reset to default configuration.
Note: Command is valid
Select Tone Dialing T
Description: This command is used to select tone dialing. Not relevant to CDMA data services; “T” is not
sent in dial string.
Syntax:
Command syntax: ATT
Command
ATT
Possible Responses
OK
Note: select tone dialing.
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Select Pulse Dialing P
Description: This command is used to select pulse dialing. Not relevant to CDMA data services; “P” is not
sent in dial string.
Syntax:
Command syntax: ATP
Command
ATP
Possible Responses
OK
Note: select pulse dialing.
Note: Command is valid
Basic S-Registers S<X>
Description: The S-registers store configuration parameters that are used for dialing or during an
established call. The value of an S-register may be set by using the syntax: ATSn=<value>
where n is the register number and <value> is a decimal value.
Values:
<n> ATS command index. Ranges from 0-11.
<value> Value for the ATS command.
Syntax:
Command syntax: ATS<n>=<value>
Command
ATS<n>=<value>
Possible Responses
OK
Note: set S-registers value
ATS0?
002
Note: Disable or enable automatic answering (value: 0-255)
OK
0: Disable;
Note: always 3 characters padded with
1-255: Enable after [(value-1)x6 sec.]
ATS3?
Note: Carriage return character
zeros
013
OK
ATS4?
Note: Line feed character
010
OK
ATS5?
Note: Backspace character
008
OK
ATS6?
002
OK
Note: Pause before blind dialing (value: 2-10)
ATS7?
050
Note: Number of seconds to establish end-to-end data connection OK
(value: 1-255)
ATS8?
002
Note: Number of seconds to pause when “,” is encountered in dial OK
string (value: 0-255)
ATS9?
006
OK
Note: Carrier detect threshold in increments of 0.1 seconds
(value: 0-255)
ATS10?
014
OK
Note: Number of tenths of a second from carrier loss to
disconnect (value: 1-254)
Value 255: disable carrier detect
ATS11?
095
Note: DTMF tone duration and spacing in milliseconds (value: 50- OK
255)
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Error Control Operation +EB
Description: This command is used for break handling in error control operations. The extended-format
compound parameter is used to control the manner of V.42 operation on the PSTN line (if
present in IWF). The command is not relevant for packet service. For more details on the
command, refer to IS707.3.
Values:
<Break_selection>
0: Ignore break (do not signal to remote DCE)
1: Non-expedited, non-destructive
2: Expedited, non-destructive
3: Expedited and destructive
<timed>
0: Any transmitted V.42 L-SIGNAL shall not indicate break signal length
1: Any transmitted V.42 L-SIGNAL shall indicate break signal length
<default_length>
0: Do not deliver break to DTE
1-254: Default break length of .01 to 2.54 seconds
Syntax:
Command syntax: AT+EB=[<Break_selection>[,<timed>[,<default_length>]]]
Command
Possible Responses
AT+EB?
+EB: 1,0,30
Note: Display the current setting.
OK
Note: This is the default setting
AT+EB=2
OK
Note: Set value to 2.
Note: Command is valid
Numeric Parameter Control +EFCS
Description: The extended-format numeric parameter is used to control the use of 32-bit frame check
sequence option in V.42 on the PSTN link (if present in IWF). The command is not relevant
for packet service.
Values:
<Val>
0: Use 16-bit FCS
1: Use 32-bit FCS if available in remote DCE; otherwise use 16-bit FCS
2: Use 32-bit FCS if available in remote DCE; otherwise disconnect
Syntax:
Command syntax: AT+EFCS=[<Val>]
Command
AT+EFCS?
Possible Responses
+EFCS: 0
Note: Display the current setting.
OK
Note: Command is valid
AT+EFCS=2
OK
Note: Set value to 2.
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Error Control Report +ER
Description: The extended-format numeric parameter is used to control whether the extended-format
+ER intermediate result code is transmitted from the IWF over the stet interface.
Values:
<Val>
0: Error control reporting disabled
1: Error control reporting enabled
Syntax:
Command syntax: AT+ER=[<Val>]
Command
Possible Responses
AT+ER?
+ER: 0
Note: Display the current setting.
OK
Note: Command is valid
AT+ER=1
OK
Note: Set value to 1.
Note: Command is valid
Error Control Selection +ES
Description: The extended-format compound parameter is used to control the manner of operation of the
V.42 protocol on the PSTN link (if present in IWF). The command is not relevant for packet
service.
Values:
<orig_rqst>
0: Direct mode
1: Initiate call with Buffered mode only
2: Initiate V.42 Detection Phase
3: Initiate Alternative Protocol
<orig_fbk>
0: Error control optional; If error control not established maintain DTE-DCE data rate
1: Error control optional; If error control not established change DTE-DCE data rate to
match line rate
2: Error control required; If error control not established, disconnect
3: Error control required (only LAPM acceptable); If error control not established,
disconnect
4: Error control required (only alternative protocol acceptable); If error control not
established, disconnect
<ans_fbk>
0: Direct mode
1: Error control disabled, use Buffered mode
2: Error control optional; If error control not established maintain DTE-DCE data rate
3: Error control optional; If error control not established change DTE-DCE data rate to
match line rate
4: Error control required; If error control not established, disconnect
5: Error control required (only LAPM acceptable); If error control not established,
disconnect
6: Error control required (only alternative protocol acceptable); If error control not
established, disconnect
Syntax:
Command syntax: AT+ES=[<orig_rqst>[,<orig_fbk>[,<ans_fbk>]]]
Command
Possible Responses
AT+ES?
+ES: 3, 0, 2
Note: Display the current setting.
OK
Note: Command is valid
AT+ES=1
OK
Note: Set value to 1.
AT+ES?
Note: Command is valid
+ES: 1, 0, 2
Note: Display the setting after change.
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Error Control Selection +ESR
Description: The extended-format numeric parameter is used to control the use of selective repeat
(SREJ) option in V.42 on the PSTN link (if present in IWF). The command is not relevant for
packet service.
Values:
<Val>
0: Do not use SREJ
1: Use SREJ if available in remote DCE; continue without it if not
2: Use SREJ if available in remote DCE; disconnect if SREJ is not available
Syntax:
Command syntax: AT+ESR=[<Val>]
Command
Possible Responses
AT+ESR?
+ESR: 0
Note: Display the current setting.
OK
Note: Command is valid
AT+ESR=1
OK
Note: Set value to 1.
Note: Command is valid
Error Control Selection +ETBM
Description: The extended-format compound parameter is used to control the handling of data remaining
in IWF buffers upon service termination. The command is not relevant for packet service.
Values:
<pending_TD>
0: Discard all buffered data immediately and disconnect
1: Attempt until all data is delivered and acknowledged (ignore timer)
2: Attempt until all data is delivered and acknowledged; If timer expires, discard
remainder
<pending_RD>
0: Discard all buffered data immediately and disconnect
1: Attempt until all data is delivered (ignore timer)
2: Attempt until all data is delivered; If timer expires, discard remainder
<timer>
0-30: Deliver timer value in seconds
other: Higher values may be supported at manufacture’s option
Syntax:
Command syntax: AT+ETBM=[<pending_TD>[,<pending_RD>[,<timer>]]]
Command
Possible Responses
+ETBM: 0, 1, 20
OK
AT+ETBM?
Note: Display the current setting.
Note: Command is valid
AT+ETBM=1
OK
Note: Set value to 1.
AT+ETBM?
Note: Display the current setting.
Note: Command is valid
+ETBM: 1, 1, 20
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Request Manufacture Identification +GMI
Description: The command is used to cause the DCE to transmit one or more lines of information text,
determined by the manufacturer, which is intended to permit the user of the DCE to identify
the manufacturer.
Syntax:
Command syntax: AT+GMI
Command
AT+GMI?
Possible Responses
ERROR
Note: Display the current setting.
AT+GMI
Note: Display the manufacturer
Note: Command is not valid
+GMI: MODEM
OK
Note: Command is valid
Request Manufacture Identification +GMM
Description: The command is used to cause the DCE to transmit one or more lines of information text,
determined by the manufacturer, which is intended to permit the user of the DCE to identify
the specific model of device.
Syntax:
Command syntax: AT+GMM
Command
AT+GMM?
Possible Responses
ERROR
Note: Display the current setting.
AT+GMM
Note: Display the model
Note: Command is not valid
+GMM: Model 72
OK
Note: Command is valid
Request Revision Identification +GMR
Description: The command is used to cause the DCE to transmit one or more lines of information text,
determined by the manufacturer, which is intended to permit the user of the DCE to identify
the version, revision level or date, or other pertinent information of the device.
Note: When there is no stored PRL, the value displayed for the PRL ID will be 0.
Syntax:
Command syntax: AT+GMR
Command
AT+GMR?
Possible Responses
ERROR
Note: Display the current setting.
AT+GMR
Note: Display the revision
Note: Command is not valid
+GMR: S/W VER: WISMOQ WQ1.8, 10015
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Request Product Serial Number Identification +GSN
Description: The command is used to cause the DCE to transmit one or more lines of information text,
determined by the manufacturer, which is intended to permit the user of the DCE to identify
the individual alphanumeric string.
Syntax:
Command syntax: AT+GSN
Command
AT+GSN?
Possible Responses
ERROR
Note: Display the current setting.
AT+GSN
Note: Display the serial number.
Note: Command is not valid
+GSN: F607A117
OK
Note: Command is valid
Request Global Object Identification +GOI
Description: The command is used to cause the DCE to transmit one or more lines of information text,
determined by the manufacturer, which is intended to permit the user of the DCE to identify
the device, based on the ISO system for registering unique object identifiers.
Syntax:
Command syntax: AT+GOI
Command
AT+GOI?
Possible Responses
ERROR
Note: Display the current setting.
Note: Command is not valid
AT+GOI
+GOI:
Note: Display the responses to the
command
OK
Note: Command is valid
Note: Currently, no information text is provided.
Modulation Selection +MS
Description: The extended-format compound parameter is used to control the manner of operation of the
modulation capabilities in the DCE.
Values:
<carrier>
manufacturer specific
<automode>
0: Disabled
1: enabled with V.8 or V.32bis Annex where applicable
<min_rate> & <min_rx_rate>
set to 0 if unspecified
<max_rate> & <max_rx_rate>
set to 0 if unspecified
Syntax:
Command syntax:
AT+MS=[<carrier>[,<automode>[,<min_rate>[,<max_rate>[,<min_rx_rate>
[,<max_rx_rate>]]]]]]
Command
Possible Responses
AT+MS?
+MS: V32B,1,1200,14400
Note: Display the parameter information.
Note: Command is valid
AT+MS=?
Note: Display the range of parameters
+MS: (V21,V22),(0,1,),(0,300-14400),(0,300-14400)
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Modulation Automode Control +MA
Description: The extended-format compound parameter is a list of modulations that the DCE may use to
connect with the remote DCE in automode operation, for answering or originating data calls.
Syntax:
Command syntax: AT+MA=[<carrier>[,<carrier>[,<carrier>[,…]]]]
Command
Possible Responses
AT+MA?
+MA: V32, V32B
Note: Display the parameter information.
Note: Command is valid
AT+MA=?
Note: Display the range of parameters
+MA: (V32B,V32,V26B,V22B,V22,V21)
Note: Command is valid
AT+MA=V32
OK
Note: Set to V32
Note: Command is valid
Modulation Reporting Control +MR
Description: The extended-format numeric parameter controls whether the extended-format
+MCR:<carrier> and +MRR:<rate> intermediate result codes are transmitted from the IWF to
the mobile station.
Values:
Syntax:
<Val>
0: Disables reporting of modulation connection
1: Enables reporting of modulation connection (+MCR and +MRR are transmitted)
Command syntax: AT+MR=[<Val>]
Command
AT+MR?
Possible Responses
+MR: 0
Note: Display the current setting.
Note: Command is valid
AT+MR=?
+MR: (0,1)
Note: Display the range of setting.
AT+MR=1
Note: Command is valid
OK
Note: Enable reporting.
Note: Command is valid
V.18 Reporting Control +MV18R
Description: The extended-format numeric parameter controls whether the extended-format +MV18R:
result code is transmitted from the IWF to the mobile station.
Values:
<Val>
0: Disables reporting of V.18 connection
1: Enables reporting of V.18 connection
Syntax:
Command syntax: AT+MV18R=[<Val>]
Command
Possible Responses
AT+MV18R?
+MV18R: 0
Note: Display the current
setting.
OK
Note: Command is valid
AT+MV18R=1
Note: Enable reporting.
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
138
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
V.18 Selection +MV18S
Description: The extended-format numeric parameter is used to control the manner of operation of the
V.18 capabilities (if present) in the DCE.
Values:
<mode>
0: Disables V.18 connection
1: V.18 operation, auto detect mode
2: V.18 operation, connection in 5-bit mode
3: V.18 operation, connect in DTMF mode
4: V.18 operation, connect in EDT mode
5: V.18 operation, connect in V.21 mode
6: V.18 operation, connect in V.23 mode
7: V.18 operation, connect in Bell 103-type mode
<dflt_ans_mode>
0: disables V.18 answer operation
1: no default specified (auto detect)
2: V.18 operation, connect in 5-bit mode
3: V.18 operation, connect in DTMF mode
4: V.18 operation, connect in EDT mode
<fbk_time_enable>
0: disable
1: enable
Syntax:
Command syntax: AT+MV18S=[<mode>[,<dflt_ans>[,<fbk_time_enable>]]]
Command
Possible Responses
+MV18S: 0, 0, 0
OK
AT+MV18S?
Note: Display the current setting.
Note: Command is valid
AT+MV18S=1,1,1
OK
Note: Set mode value to 1.
AT+MV18S?
Note: Display the current setting.
Note: Command is valid
+MV18S: 1, 1, 1
OK
Note: Command is valid
Cellular Extension +CXT
Description: The numeric parameter is used for cellular extension.
Values:
<Val>
0: Do not pass unrecognized commands to the IWF
1: When detecting an unrecognized AT command, open transport layer connection and
pass unrecognized command to the IWF.
Syntax:
Command syntax: AT+CXT=<Val>
Command
Possible Responses
AT+CXT?
+CXT: 0
Note: Display the current setting.
OK
Note: Command is valid
AT+CXT=?
+CXT: (0-1)
Note: Display the range of setting.
OK
Note: Command is valid
AT+CXT=1
OK
Note: Enable extension.
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Configuration String +CFG
Description: The string command is used to set configuration string. The string will be stored by the DCE
and sent to the base station prior to dialing. Each transmission of an AT+CFG command
from DTE replaces the contents of the previous string. The string may be up to 248
characters in length.
Syntax:
Command syntax: AT+CFG=<string >
Command
Possible Responses
AT+CFG?
+CFG: “”
Note: Display the current setting.
OK
AT+CFG=””
OK
Note: Reset the configuration string.
AT+CFG=”data”
Note: Command is valid
OK
Note: Set the configuration string.
Note: Command is valid
Query Service +CAD
Description: The numeric parameter is used to query analog or digital service.
Values:
The command should return one of the following codes:
0: If no service is available
1: If CDMA digital service is available
2: If TDMA digital service is available
3: If analog service is available (values 4 to 255 reserved)
Syntax:
Command syntax: AT+CAD
Command
AT+CAD?
Possible Responses
+CAD: 1
Note: Display the current service.
OK
Note: Command is valid
Um Interface Data Compression Reporting +CDR
Description: The extended-format numeric parameter is used to control whether the extended-format
+CDR: intermediate result code is transmitted by the DCE. The result code is the same as
for the TIA/EIS/IS-131 +DR:<result code>.
Values:
<val>
0: Disable reporting.
1: Enable reporting.
Syntax:
Command syntax: AT+CDR=<val>
Command
AT+CDR?
Possible Responses
+CDR: 0
Note: Display the current code
OK
Note: Command is valid
AT+CDR=1
OK
Note: Reporting enabled
AT+CDR=?
Note: Display the range of code
Note: Command valid
+CDR: (0-1)
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
140
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Um Interface Data Compression +CDS
Description: This command is an overloaded command that serves as an unsolicited SMS command and
also as a data compression command. The unsolicited SMS command is explained in
Chapter 3. The data compression command has an extended-format numeric parameter that
is used to control the V.42bis data compression function on the Um interface. The command
format is the same as for the TIA/EIS/IS-131 +DS command.
Syntax:
Command syntax: AT+CDS=<Val>
Command
AT+CDS?
Possible Responses
+CDS: 0, 1, 2048, 6
OK
Note: Display the current setting.
Note: Command is valid
+CDS: (0-0),(1-1),(512-65535),(6-250)
OK
AT+CDS=?
Note: Display the range of setting.
Note: Command is valid
Note: Currently, mobile only accept 0 as a valid setting.
Set Rm Interface Protocol +CRM
Description: The numeric parameter is used for set the Rm interface protocol.
Values:
<Val> 0: Asynchronous Data or Fax
1: Packet data service, Relay Layer Rm interface
2: Packet data service, Network Layer Rm interface, PPP
Note: The values 3 and 4 are currently not supported.
3: Packet data service, Network Layer Rm interface, SLIP
4: STU-III Service
Syntax:
Command syntax: AT+CRM=<Val>
Command
Possible Responses
+CRM: 0
AT+CRM?
Note: Display the current setting.
OK
Note: Command is valid
AT+CRM=?
+CRM: (0-2)
Note: Display the range of setting.
OK
Note: Command is valid
AT+CRM=1
OK
Note: Set to 1.
Note: Command is valid
Note: This default value for the +CRM parameter shall be 0 if this value is supported by the
DCE.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Battery Charge +CBC
Description: This command is used to query the current state of the modem power source. An estimate
of the remaining capacity is included if a battery connection is in use.
Values:
<BCS> Battery Charge Status:
0: Mobile powered by battery; followed by <BCL>, percent of battery remaining
1: Mobile connected to external power
2: Battery status not available 3: Recognized power fault. Calls inhibited.
<BCL> Battery Charge Level:
0 – 100: Remaining battery capacity is 0 – 100%.
Syntax:
Command syntax: AT+CBC Read-only. Returns <BCS>,<BCL>
Command
Possible Responses
AT+CBC?
+CBC: 0, 77
Note: Display the current status
OK
Note: Command is valid
AT+CBC
ERROR
Note: Command is not valid
Command State Inactivity Timer +CQD
Description: The numeric parameter is used to query and set the Command State Inactivity Timer.
Values:
<val>
0: Ignored
1-255: Release call after 5x<val> seconds have elapsed without activity.
Note: The default <val> shall be 10, corresponding to 50 seconds.
Syntax:
Command syntax: AT+CQD=<val>
Command
AT+CQD?
Possible Responses
+CQD: 10
Note: Display the current setting.
OK
Note: Command is valid
AT+CQD=0
OK
Note: Set the value to 0.
Note: Command is valid
Mobile Station IP Address +CMIP
Description: This read-only command is used to display the mobile station’s temporary IP address. The
value displayed is in standard IP address format.
Note: This command returns an IP value only during a data call when a temporary IP
address has been assigned. When not in a data call, this command returns “OK”.
Syntax:
Command syntax: AT+CMIP
Command
AT+CMIP?
Possible Responses
+CMIP: 198.229.142.90
OK
Note: Display the current setting
Note: Command is valid
AT+CMIP?
OK
Note: Display the current setting
AT+CMIP
Note: When no IP address assigned.
ERROR
Note: Command is not valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
142
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Base Station IP Address +CBIP
Description: This read-only command is used to display the base station’s temporary IP address. The
value displayed is in standard IP address format.
Note: This command returns an IP value only during a data call when a temporary IP
address has been assigned. When not in a data call, this command returns “OK”.
Syntax:
Command syntax: AT+CBIP
Command
Possible Responses
AT+CBIP?
Note: Display the current setting
+CBIP: 198.229.142.65
OK
Note: Command is valid
AT+CBIP?
OK
Note: Display the current setting
AT+CBIP
Note: No IP address assigned.
ERROR
Note: Command is not valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
143
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Serving System +CSS
Description: The numeric parameter is used to query the serving system.
Values: <Class>
0: No service
1: 800Mhz
2: 1900Mhz PCS
<Band>
A – C: Cellular 800
PA – PF: PCS 1900
Z: The mobile station is not registered
Note: For the <Band> parameter, the value will be two letters for PCS. The first will be ‘P’
and the second will be the block (‘A’ – ‘F’).
<SID>
0 – 32767: The mobile station is registered with the system indicated.
99999: The mobile station is not registered.
<BS_P_REV> (Base Station Protocol Revision In Use – Band Class 0/Cellular)
1: IS-95
2: IS-95A
3: TSB74
4: N/A
5: IS-95B
6: IS-2000
7: IS-2000A
<BS_P_REV> (Base Station Protocol Revision In Use – Band Class 1/PCS)
1: J-STD-008C
2: N/A
3: N/A
4: N/A
5: IS-95B
6: IS-2000
7: IS-2000A
<CHANNEL>
0 – Max RF Channel Number
Syntax:
Command syntax: AT+CSS Returns: <Class>,<Band>,<SID>,<BS_P_REV>,<CHANNEL>
Command
Possible Responses
AT+CSS?
+CSS: 2, A, 4145, 6, 334
Note: Display the current setting.
OK
Note: Command is valid
AT+CSS=?
+CSS:
Note: Display the parameter range.
OK
Note: Command is valid however range display is not
supported for this command due to carrier-specific
requirements.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
144
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Select Multiplex Option +CMUX
Description: The numeric parameter is used to select multiplex option.
Values:
<n>
1: Multiplex Option 1
2: Multiplex Option 2
Syntax:
Command syntax: AT+CMUX=<n>
Command
AT+CMUX?
Possible Responses
+CMUX: C, 2
Note: Display the current setting.
OK
Note: Command is valid
+CMUX: (1-9,A-F), (1,2)
OK
AT+CMUX=?
Note: Display valid parameter range.
Note: Command is valid
AT+CMUX=1
OK
Note: Set multiplex option 1.
Note: Command is valid
Um Interface Fax Compression +CFC
Description: The numeric parameter is used to set the Um Interface Fax Compression.
Values:
<Val>
0: No compression
1: V.42bis compression with parameters as set by the +CDS command
2: Modified Read compression
Note: Currently, the values 1 and 2 are not supported.
Syntax:
Command syntax: AT+CFC=<Val>
Command
Possible Responses
AT+CFC?
+CFC: 0
Note: Display the current setting.
OK
Note: Command is valid
AT+CFC=?
Note: Display the range of the setting.
+CFC: (0-2)
OK
Note: Command is valid
AT+CFC=0
OK
Note: Set no compression.
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
145
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
Hang-up Voice +CHV
Description: The numeric parameter is used to Hang-up a voice call. It terminates a voice connection
previously established up +CDV (dial voice) or $QCCAV (answer voice). The only valid
parameter is zero, which is optional.
Values:
Syntax:
<n>
0: Hang-up voice call
1-255: Reserved.
Command syntax: AT+CHV<n>
Command
Possible Responses
AT+CHV
OK
Note: Display the current setting.
Note: Command is valid
AT+CHV0
OK
Note: Hang up the call.
Note: Command is valid
Dial Command for Voice Calls +CDV
Description: The numeric parameter is used to dial command for voice calls. The format of <dialstring> is
identical to that for the ATD command. This command does not cause the DCE to change to
the online state.
Syntax:
Command syntax: AT+CDV=<dial_string>
Command
AT+CDV?
Possible Responses
ERROR
Note: Display the current setting.
AT+CDV=8583693450
Note: Dial for voice call.
Note: Command is not valid
OK
+WORG: 8583693450
+WCNT: 3
Note: Command is valid
IWF Content List +CGCAP
Description: This extended-format command requests the IWF to transmit one or more lines of
information text in a specific format. The content is a list of additional capabilities and AT+
commands which is intended to permit the user of the IWF to identify the minimum
capabilities of the IWF. This is used to determine if the services (such as +CIS707, +MS,
+ES, +DS, and +FCLASS) can be performed by the IWF. See IS-131 on details and
parameter use.
Syntax:
Command syntax: AT+CGCAP
Command
AT+ CGCAP
Possible Responses
+CGCAP:
Note: Display the current setting.
OK
Note: Command is valid
AT+ CGCAP=0
ERROR
Note: Set the value to 0.
Note: Command is not valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
146
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 17 – Extended AT Commands in IS707.3
IWF Device Identification +CGOI
Description: This command causes the IWF to transmit one or more lines of information text, determined
by the manufacturer, which is intended to permit the user of the IWF to identify the device,
based on the ISO system for registering unique object identifiers. Typically, the text will
consist of a single line containing numeric strings delimited by period characters.
Syntax:
Command syntax: AT+CGOI
Command
AT+CGOI
Possible Responses
OK
Note: Display the current settings.
Note: Command is valid.
AT+CGOI=0
ERROR
Note: Set the value to 0.
Note: Command is not valid.
Um Packet Data Inactivity Timer +CTA
Description: This command is used to Set, Read, and Test the Um packet data inactivity timer.
Values:
<val>
0: Traffic Channel not released during inactivity periods.
20-255: Release the Traffic Channel after <value> 1-second intervals have elapsed
since last sending or receiving RLP data frames on the Um interface.
Syntax:
Command syntax: AT+CTA=<val>
Command
AT+CTA ?
Possible Responses
+CTA: 0
Note: Display the current setting.
OK
Note: Command is valid
+CTA: (0-255)
OK
AT+CTA=?
Note: Display valid parameter range.
Note: Command is valid
AT+CTA=1 Note: Set to one second.
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
147
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 18 - Fax Parameters
CHAPTER 18 – FAX PARAMETERS
This chapter lists tables from the IS-707.3 fax parameters for user reference.
IS-707.3 Fax Parameters
Description
Parameter
+FAA
+FAP
+FBO
+FBS
+FBU
+FCC
VR
Value (per)
Type
EIA/TIA-592
TIA/EIA/IS-134
EIA/TIA-592
EIA/TIA-592
EIA/TIA-592
Adaptive-answer parameter (see +FCLASS)
Addressing and polling capabilities parameter
Phase-C data-bit-order parameter
Buffer size parameter (read-only)
HDLC-frame-reporting parameter
DCE-capabilities parameters
Vertical-resolution sub-parameter
Bit-rate sub-parameter
Remote
Remote
Remote
Local
Remote
Remote
EIA/TIA-592
[BR]
• 2400 bits/s
0
• 4800 bits/s
1
• 7200 bits/s
• 9600 bits/s
2
31
Page-width sub-parameter
Page-length sub-parameter
WD
[LN]
[DF]
[EC]
BF
EIA/TIA-592
EIA/TIA-5922
EIA/TIA-5922
EIA/TIA-5922
EIA/TIA-592
EIA/TIA-592
Data-compression-format sub-parameter
Error-correction sub-parameter
Binary-file-transfer sub-parameter
Scan-time-per-line sub-parameter
Service-class selection parameter
• Class-0
ST
[+FCLASS]
Remote
0
1
• [Class-1 support unavailable]
• Class-2.0 fax service (EIA/TIA-592)
Copy quality-checking parameter
Capability-to-receive parameter
Current-session results parameters
DTE Phase-C timeout parameter
Phase-C received EOL-alignment parameter
Format-conversion parameter
Call termination-status parameter
Procedure-interrupt-enable parameter
Current session negotiation parameters
Local-ID-string parameter (TSI or CSI)
Flow-control-select parameter
Indicate-document-to-poll parameter
Request DCE manufacturer identification
Request DCE model
2.03
+FCQ
[+FCR]
+FCS
+FCT
+FEA
+FFC
+FHS
+FIE
EIA/TIA-592
EIA/TIA-5922
EIA/TIA-592
EIA/TIA-592
EIA/TIA-592
EIA/TIA-592
EIA/TIA-592
EIA/TIA-592
EIA/TIA-592
EIA/TIA-5922
EIA/TIA-5922
EIA/TIA-592
EIA/TIA-592
EIA/TIA-592
EIA/TIA-592
EIA/TIA-5922
Remote
Remote
Remote
Remote
Remote
Remote
Remote
Remote
Remote
Remote
Local
Remote
See 4.3.5
See 4.3.5
See 4.3.5
Remote
+FIS
[+FLI]
+FLO
+FLP
+FMI
+FMM
+FMR
[+FMS]
Request DCE revision
Minimum-Phase-C-speed parameter
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
148
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 18 - Fax Parameters
IS-707.3 Fax Parameters
Parameter
+FNR
Value (per)
Description
Type
EIA/TIA-592
Negotiation-message-reporting control
Remote
parameters
+FNS
+FPA
EIA/TIA-592
TIA/EIA/IS-134
EIA/TIA-5922
EIA/TIA-5924
EIA/TIA-592
EIA/TIA-5925
TIA/EIA/IS-134
EIA/TIA-5922
EIA/TIA-592
TIA/EIA/IS-134
EIA/TIA-5922
Nonstandard-frame FIF parameter
Selective Polling Address Parameter
Local-polling-ID-string parameter
Packet-protocol-control parameter
Serial port-rate-control parameter
Page-status parameter
Password parameter (Sending or Polling)
Receive-quality-threshold parameters
ECM retry-value parameter
Remote
Remote
Remote
Local
Local
Remote
Remote
Remote
Remote
Remote
Remote
[+FPI]
[+FPP]
+FPR
[+FPS]
+FPW
[+FRQ]
+FRY
+FSA
Sub address Parameter
Request-to-poll parameter
[+FSP]
Notes
1. Use of option 3 may cause degradations in the quality of certain faxes.
2. Some values for this parameter are optional in EIA/TIA-592. In this standard, all parameters of this command
shall be supported.
3. Class 2.0 represents EIA/TIA-592.
4. Support of packet protocol is optional.
5. Values 4 and 5 of this parameter are optional.
IS-707.3 Fax Action Commands
Command
+FDR
+FDT
+FIP
+FKS
Description
Type
Receive Phase-C data.
Transmit Phase-C data.
Initialize facsimile parameters.
Terminate session.
Remote
Remote
Remote
Remote
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
149
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
CHAPTER 19 - QUALCOMM DEFINED AT COMMANDS FOR
CDMA OPERATION
This section contains AT commands that are specified and developed by Qualcomm.
Note: Mobile IP related AT commands work only on the modems that supported the MIP features.
Transition to Diagnostics Monitor $QCDMG
Description: This command returns “OK” and then transitions the phone serial port to DM mode. DM
mode runs at 38.4 Kbps and uses a proprietary half-duplex protocol.
Syntax:
Command syntax: AT$QCDMG
Command
Possible Responses
AT$QCDMG
OK
Note: Transition to DM port
Note: Command is valid
Quick Net Connect $QCQNC
Description: This command is used to enable or disable the Quick Net Connect (QNC) feature.
Values:
<Val>
0: Disable QNC capability. This means that packet Originations will use the Packet Data
Service Option number.
1: Enable QNC capability. This means that Packet Originations will use the Async Data
Service Option number.
Syntax:
Command syntax: AT$QCQNC=<Val>
Command
AT$QCQNC?
Possible Responses
$QCQNC: 0
Note: Display the current setting
OK
Note: Command is valid
$QCQNC: (0-1)
OK
AT$QCQNC=?
Note: Display the range of values
Note: Command is valid
AT$QCQNC=1
OK
Note: Enable QNC compatibility
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
150
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Protocol Revision in Use $QCPREV
Description: This command is used to query the protocol revision in use.
Values:
The command will return one of the following codes:
1: JST008
3: IS-95A
4: IS-95B
6: IS-2000
Syntax:
Command syntax: AT$QCPREV
Command
Possible Responses
AT$QCPREV?
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCPREV
$QCPREV: 6
Note: Display the of value
OK
Note: Command is valid
Originate M-to-M Packet Data Call $QCMTOM
Description: This command is used to originate a Mobile-to-Mobile Packet Data call using the
QUALCOMM proprietary Service Option number.
Values:
Syntax:
<number>
where <number> is the phone number to dial. This command will originate a Mobile-to-
Mobile Packet data call using the QUALCOMM-proprietary Service Option number
0x8003. This is a Rate Set 1 call.
Command syntax: AT$QCMTOM = ‘’<number>’’
Command
Possible Responses
AT$QCMTOM?
$QCMTOM: “”
Note: Display the current setting
OK
Note: Command is valid
$QCMTOM: (20,21,23-7E)
OK
AT$QCMTOM =?
Note: Display the range of values
Note: Command is valid
AT$QCMTOM =”#777”
OK
Note: Packet data call to the number
Note: Command is valid
Dump RLP Protocol Statistics $QCRLPD
Description: This command is used to dump the RLP statistics in ASCII format to the DTE. This does not
apply to RLP 3 statistics (see $QCRL3D).
Syntax:
Command syntax: AT$QCRLPD
Command
Possible Responses
AT$QCRLPD?
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCRLPD
$QCRLPD:
Note: Dump RLP statistics data
Rx Data Cnt :0000 Tx Data Cnt :0000
….
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
151
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Reset RLP Protocol Statistics $QCRLPR
Description: This command is used to zero all the RLP statistics counters. This does not apply to RLP 3
statistics (see $QCRL3R).
Syntax:
Command syntax: AT$QCRLPR
Command
AT$QCRLPR?
Possible Responses
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCRLPR
$QCRLPR:
Note: Reset RLP statistics counter
OK
Note: Command is valid
Dump PPP Protocol Statistics $QCPPPD
Description: This command is used to dump the PPP statistics in ASCII format to the DTE.
Syntax:
Command syntax: AT$QCPPPD
Command
AT$QCPPPD?
Possible Responses
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCPPPD
$QCPPPD:
Note: Dump PPP statistics information
In LCP :0000 Out LCP :0000
….
OK
Note: Command is valid
Reset PPP Protocol Statistics $QCPPPR
Description: This command is used to zero all of the PPP statistics counters.
Syntax:
Command syntax: AT$QCPPPR
Command
AT$QCPPPR?
Possible Responses
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCPPPR
$QCPPPR:
Note: Reset PPP statistics counter
OK
Note: Command is valid
Dump IP Protocol Statistics $QCIPD
Description: This command is used to dump the IP statistics in ASCII format to the DTE.
Syntax:
Command syntax: AT$QCIPD
Command
Possible responses
AT$QCIPD?
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCIPD
$QCIPD:
Note: Dump IP statistics information
IP:
InReceives :0000 InHdrErrors :0000
….
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
152
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Reset IP Protocol Statistics $QCIPR
Description: This command is used to zero all of the IP statistics counters.
Syntax:
Command syntax: AT$QCIPR
Command
AT$QCIPR?
Possible Responses
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCIPR
$QCIPR:
Note: Reset IP statistics counter
OK
Note: Command is valid
Dump UDP Protocol Statistics $QCUDPD
Description: This command is used to dump the UDP statistics in ASCII format to the DTE.
Syntax:
Command syntax: AT$QCUDPD
Command
Possible Responses
AT$QCUDPD?
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCUDPD
$QCUDPD:
Note: Dump UDP statistics information
InDatagrams :0000 OutDatagrams :0000
….
OK
Note: Command is valid
Reset UDP Protocol Statistics $QCUDPR
Description: This command is used to zero all of the UDP statistics counters.
Syntax:
Command syntax: AT$QCUDPR
Command
AT$QCUDPR?
Possible Responses
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCUDPR
$QCUDPR:
Note: Reset UDP statistics counter
OK
Note: Command is valid
Dump TCP Protocol Statistics $QCTCPD
Description: This command is used to dump the TCP statistics in ASCII format to the DTE.
Syntax:
Command syntax: AT$QCTCPD
Command
Possible Responses
AT$QCTCPD?
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCTCPD
$QCTCPD:
Note: Dump TCP statistics information
ActiveOpens :0000 PassiveOpens :0000
….
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
153
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Reset TCP Protocol Statistics $QCTCPR
Description: This command is used to zero all of the TCP statistics counters.
Syntax:
Command syntax: AT$QCTCPR
Command
AT$QCTCPR?
Possible Responses
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCTCPR
$QCTCPR:
Note: Reset TCP statistics counter
OK
Note: Command is valid
Set Data Service Option $QCSO
Description: This command is used to Set Data Service Option number set; saves to non-volatile
memory.
Values:
<Val>
0 : pre-707 SO numbers (RS 1: Async 4, G3 Fax 5, packet 7; RS 2: Async 12, G3 Fax
13, packet 15)
1 : proprietary SO numbers (RS 1: Async 4, G3 Fax 5, packet 7; RS 2: Async 0x8021,
G3 Fax 0x8022, packet 0x8020)
2 : IS-707 SO numbers (RS 1: Async 0x1004, G3 Fax 0x1005, packet 0x1007; RS 2:
Async 12, G3 Fax 13, packet 15)
Syntax:
Command syntax: AT$QCSO =<Val>
Command
AT$QCSO?
Possible Responses
$QCSO: 2
Note: Display the current setting
OK
Note: Command is valid
$QCSO: (0-2)
OK
AT$QCSO =?
Note: Display the range of values
Note: Command is valid
AT$QCSO =1
OK
Note: Set proprietary SO
numbers.
Note: Command is valid
Clear Mobile Error Log $QCCLR
Description: This command is used to clear the mobile error log.
Syntax:
Command syntax: AT$QCCLR
Command
AT$QCCLR?
Possible Responses
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCCLR
$QCCLR:
Note: Clear the mobile error log
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
154
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Answer Incoming Voice Call $QCCAV
Description: This command is used to provide a means to answer an incoming voice call via an AT
command.
Syntax:
Command syntax: AT$QCCAV
Command
AT$QCCAV
Possible Responses
OK
Note: Answer incoming voice call
+WCNT: 3
Note: Command is valid
Automatic Packet Detection $QCPKND
Description: This command is used to enable or disable Automatic Packet Detection after a dial
command.
Values:
<Val>
0 : Disable Packet No Dial. If a PPP packet is received by the mobile without a just prior
dial command (that is, ATD#nnn e.g. ATD#777), then the mobile will originate a Packet
(or QNC) data call.
1 : Enable Packet No Dial. Reception of a PPP packet without a just prior dial command
will NOT Originate a PPP packet (or QNC) call.
Syntax:
Command syntax: AT$QCPKND=<Val>
Command
AT$QCPKND?
Note: Display the current setting
Possible Responses
$QCPKND: 0
OK
Note: Command is valid
$QCPKND: (0-1)
OK
AT$QCPKND=?
Note: Display the range of values
Note: Command is valid
AT$QCPKND=1
OK
Note: Enable Packet No Dial
Note: Command is valid
Pre-arrangement Setting $QCVAD
Description: This command is used to respond to a page message that has a voice service option with a
page response that has a data service option.
Values:
<Val>
0 : Off
1 : Fax for next call
2 : Fax for all calls
3: Async for next call
4: Async for all calls
Syntax:
Command syntax: AT$QCVAD= <Val>
Command
AT$QCVAD?
Possible Responses
$QCVAD: 0
Note: Display the current setting
OK
Note: Command is valid
$QCVAD: (0-4)
OK
AT$QCVAD=?
Note: Display the range of values
Note: Command is valid
AT$QCVAD=1
OK
Note: Set fax for next call
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
155
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Set DM Baud Rate $QCDMR
Description: This command is used to set the DM baud rate.
Values:
Syntax:
<Val> value should be one of the following: 19200, 38400, 57600, 115200
Command syntax: AT$QCDMR= <Val>
Command
Possible Responses
AT$QCDMR?
$QCDMR: 19200
Note: Display the current setting
OK
Note: Command is valid
AT$QCDMR=?
$QCDMR: (19200, 38400, 57600, 115200, 230400, 460800)
Note: Display the range of values
OK
Note: Command is valid
AT$QCDMR=115200
OK
Note: Set DM baud rate to 115200
Note: Command is valid
Set Medium Data Rate $QCMDR
Description: This command is used to Set Medium Data Rate (MDR) (also known as HSPD) setting.
Values:
<Val>
0: MDR Service Only. The mobile will originate with SO 22 or SO 25. The mobile will not
negotiate to any other service option if SO 22 and SO 25 are unavailable.
1: MDR Service, if available. The mobile will originate with SO 22 or SO 25, but will
negotiate to a Low-Speed Packet service option if MDR is not available. The mobile will
not negotiate to SO 33.
2: LSPD only. The mobile will originate a Low-Speed Packet call only. The mobile will
not negotiate to SO 22, SO 25, or SO 33.
3: SO 33, if available. The mobile will negotiate to MDR or Low-Speed Packet service
options if SO 33 is not available.
Syntax:
Command syntax: AT$QCMDR=<Val>
Command
AT$QCMDR?
Possible Responses
$QCMDR: 3
Note: Display the current setting
OK
Note: Command is valid
$QCMDR: (0-3)
OK
AT$QCMDR=?
Note: Display the range of values
Note: Command is valid
AT$QCMDR=1
OK
Note: Set value to 1
Note: Command is valid
Dump RLP 3 Protocol Statistics $QCRL3D
Description: This command is used to dump the RLP 3 statistics in ASCII format to the DTE. This does
not apply to other versions of RLP (see $QCRLPD).
Syntax:
Command syntax: AT$QCRL3D
Command
Possible Responses
AT$QCRL3D?
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCRL3D
$QCRL3D:
Note: Dump RLP 3 statistics information
Rx Data Cnt :00000000 Tx Data Cnt :00000000
….
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
156
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Reset RLP 3 Protocol Statistics $QCRL3R
Description: This command is used to reset the RLP 3 protocol statistics.
Syntax:
Command syntax: AT$QCRL3R
Command
AT$QCRL3R?
Possible Responses
ERROR
Note: Display the current setting
Note: Command is not valid
AT$QCRL3R
$QCRL3R:
Note: Reset TCP statistics counter
OK
Note: Command is valid
SCRM’ing Selection $QCSCRM
Description: This command is used to enable or disable the mobile from SCRM’ing.
Values:
<Val>
0 : Mobile never SCRMs.
1 : Mobile can SCRM as needed.
Note: Command only applies to SO 33 calls. This value is stored in NV. The default is 1.
Command syntax: AT$QCSCRM= <Val>
Syntax:
Command
AT$QCSCRM?
Note: Display the current setting
Possible Responses
$QCSCRM: 1
OK
Note: Command is valid
$QCSCRM: (0-1)
OK
AT$QCSCRM =?
Note: Display the range of values
Note: Command is valid
AT$QCSCRM =0
OK
Note: Set value to 0
Note: Command is valid
R-SCH Selection $QCTRTL
Description: This command is used to enable or disable mobile R-SCH throttling.
Values:
<Val>
0: Mobile never throttles R-SCH
1: Mobile can throttle R-SCH as needed.
Note: Command only applies to SO 33 calls. This value is stored in NV. The default is 1. For
MSM500, MSM5105, and MSM5100 ASICs only.
Syntax:
Command syntax: AT$QCTRTL=<Val>
Command
AT$QCTRTL?
Possible Responses
$QCTRTL: 1
Note: Display the current setting
OK
Note: Command is valid
$QCTRTL: (0-1)
OK
AT$QCTRTL =?
Note: Display the range of values
Note: Command is valid
AT$QCTRTL =0
OK
Note: Set value to 0
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
157
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
R-SCH Selection $QCMIP
Description: This command is used to enable or disable mobile IP.
Values:
<Val>
0: Mobile IP disabled, Simple IP only.
1: Mobile IP preferred. In the initial MIP registration, if the network does not support
Mobile IP, then the mobile automatically reverts to Simple IP (force a PPP renegotiation
by sending a LCP C-Req).
However, if a Mobile IP session is registered, and then enters a network that does not
support Mobile IP, the mobile will drop the session and inform the upper layers of the
failure (for example, by dropping DCD to a laptop).
2: Mobile IP only. The mobile will make data calls only when Mobile IP is supported in
the network. During a MIP session, if the mobile hands off to a network that does not
support MIP, then the mobile will drop the session and inform the upper layers of the
failure (for example, by dropping DCD to a laptop). This value is stored in NV. The
default value is 0.
Note 1: When the AT$QCMIP value is changed to 1 or 2, this modifies the value of
AT+CRM to 2. AT+CRM with a value of 2 enables network model operation. Changing the
value to 0 will reset the AT+CRM to its original value.
Note 2: This change is not supported by DMSS 5105 Release 1.0 Commercial.
Note 3: When the AT$QCMIP value is changed to 1 or 2, this modifies the value of
AT$QCMDR to 3. AT$QCMDR=3 means that the mobile tries Service Option 33 when it is in
a cdma2000 network that advertises P_REV 6 or higher. When AT$QCMIP >0 and an
attempt is made to set AT$QCMDR to less than 3, the mobile will return ERROR.
Note 4: When the AT$QCMIP value is set to 1 or 2, this changes the value of AT$QCPKND
to 0. This means that the mobile must see a dial string (such as ATDT#777) on the serial
interface before it will originate packet data calls. When AT$QCMIP >0 and an attempt is
made to set AT$QCPKND to 1, the mobile returns ERROR.
Note 5: This AT command is for test purposes only and should not be changed by the
mobile phone user.
Syntax:
Command syntax: AT$QCMIP=<Val>
Command
Possible Responses
AT$QCMIP?
$QCMIP: 1
Note: Display the current setting
OK
Note: Command is valid
AT$QCMIP=?
Note: Display the range of values
$QCMIP: (0-2)
OK
Note: Command is valid
AT$QCMIP=0
OK
Note: Set value to 0
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
158
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
MIP Selection $QCMIPP
Description: This command is used to select and activate an MIP user profile.
Syntax:
Command syntax: AT$QCMIPP
Command
AT$QCMIPP?
Possible Responses
$QCMIPP: 0
Note: Display the current setting
Note: User profile 1 is currently used
AT$QCMIPP=2
OK
Note: Set to user profile 2
AT$QCMIPP=?
Note: Display the range of values
Note: Command is valid
$QCMIPP: (0-5)
OK
Note: Command is valid
Note: Takes a profile number between 0 and 5. This value is stored in NV. This AT
command is used to configure Dial-Up Networking.
RFC2002bis Selection $QCMIPT
Description: This command is used to enable or disable the use of rfc2002bis authentication.
Values:
<Val>
0: Use of rfc2002bis authentication is disabled. Rfc2002 style authentication is used
instead.
1: Use of rfc2002bis authentication is enabled.
Note: This AT command is for test purposes only and should not be changed by the mobile
phone user.
Syntax:
Command syntax: AT$QCMIPT=<Val>
Command
AT$QCMIPT?
Possible Responses
$QCMIPT: 1
Note: Display the current setting
OK
Note: Command is valid
$QCMIPT: (0-3)
OK
AT$QCMIPT=?
Note: Display the range of values
Note: Command is valid
AT$QCMIPT=0
OK
Note: Set value to 0
Note: Command is valid
Current Active Profile $QCMIPEP
Description: This command is used to enable or disable the currently active profile.
Values:
<Val>
0: Disable the currently active profile (profile is unavailable until it is re-enabled.
1: Enable the currently active profile.
Syntax:
Command syntax: AT$QCMIPEP=<Val>
Command
AT$QCMIPEP?
Possible Responses
$QCMIPEP: 1
OK
Note: Display the current setting
Note: Command is valid
$QCMIPEP: (0-1)
OK
AT$QCMIPEP=?
Note: Display the range of values
Note: Command is valid
AT$QCMIPEP=0
OK
Note: Set value to 0
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
159
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Return Profile Information $QCMIPGETP
Description: This command is used to return all information corresponding to the specified profile
number.
Values:
<Val>
(0-5): Profile #
Note: If no profile number is entered, all information corresponding to the currently active
profile is returned. If there is no profile associated with the specified number, an error is
returned.
Syntax:
Command syntax: AT$QCMIPGETP=<Val>
Command
Possible Responses
AT$QCMIPGETP?
ERROR
Note: Display the current setting
AT$QCMIPGETP=?
Note: Display the range of values
Note: Command is not valid
$QCMIPGETP: (0-5)
OK
Note: Command is valid
Profile:0 Enabled
…..
AT$ CMIPGETP=0
Note: Set value to 0
OK
Note: Command is valid
Set NAI for Active Profile $QCMIPNAI
Description: This command is used to set the network access identifier (NAI) for the currently active
profile.
Values:
<String> The network access identifier text to be stored.
<Val>
0: Do not commit to NV
1: Commit to NV
Note 1: Double quotes are only required if the string contains a command.
Note 2: If the value provisioned is not committed to NV, the temporary value will be deleted
at the end of the following call if $QCMIPP is called.
Syntax:
Command syntax: AT$QCMIPNAI=<String>,<Val>
Command
Possible Responses
AT$QCMIPNAI?
Note: Display the current setting
OK
Note: Command is valid
AT$QCMIPNAI=?
Note: Display the range of accepted
character values.
$QCMIPNAI: (20,21,23-7E),(0-1)
OK
Note: ASCII hexadecimal character range supported by
this command. (All non-control codes.)
AT$QCMIPNAI=myName@myDom
ain.com,0
OK
Note: NAI is now: [email protected]
Note: Non-committed value set
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
160
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Set Reverse Tunneling $QCMIPRT
Description: This command is used to set the reverse tunneling currently active profile.
Values:
<Val1>
0: Do not request reverse tunneling
1: Request reverse tunneling
<Val2>
0: Do not commit to NV
1: Commit to NV
Note: If the value provisioned is not committed to NV, the temporary value will be deleted at
the end of the following call if $QCMIPP is called.
Syntax:
Command syntax: AT$QCMIPRT=<Val1>, <Val2>
Command
Possible Responses
$QCMIPRT: 1,1
OK
AT$QCMIPRT?
Note: Display the current setting
Note: Command is valid
$QCMIPRT: (0-1), (0-1)
OK
AT$QCMIPRT=?
Note: Display the range of values
Note: Command is valid
AT$QCMIPRT=1,1
OK
Note: Set value to 1 and commit
Note: Command is valid
Set MN-AAA Shared Secrets $QCMIPMASS
Description: This command is used to set MN-AAA shared secrets for the currently active profile.
Values:
<String> The shared secret text to be stored.
<Val>
0: Do not commit to NV
1: Commit to NV
Note 1: Double quotes are only required if the string contains a command.
Note 2: If the value provisioned is not committed to NV, the temporary value will be deleted
at the end of the following call if $QCMIPP is called.
Syntax:
Command syntax: AT$QCMIPMASS =<String>,<Val>
Command
Possible Responses
AT$QCMIPMASS?
Note: Display the current setting
$QCMIPMASS: Set
OK
Note: Command is valid
AT$QCMIPMASS=?
$QCMIPMASS: (20,21,23-7E),(0-1)
Note: Display the range of accepted
character values.
OK
Note: ASCII hexadecimal character range supported by this
command. (All non-control codes.)
OK
AT$QCMIPMASS= my5ecretC0de,0
Note: Non-committed value set
Note: MN-AAA is now: my5ecretC0de
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
161
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Set MN-HA Shared Secrets $QCMIPMHSS
Description: This command is used to set MN-HA shared secrets for the currently active profile.
Values:
<String>The shared secret text to be stored.
<Val>
0: Do not commit to NV
1: Commit to NV
Note 1: Double quotes are only required if the string contains a command.
Note 2: If the value provisioned is not committed to NV, the temporary value will be deleted
at the end of the following call if $QCMIPP is called.
Syntax:
Command syntax: AT$QCMIPMHSS =<String>,<Val>
Command
Possible Responses
$QCMIPMHSS: Set
OK
AT$QCMIPMHSS?
Note: Display the current setting
Note: Command is valid
$QCMIPMHSS: (20,21,23-7E),(0-1)
OK
AT$QCMIPMHSS=?
Note: Display the range of values
Note: Command is valid
AT$QCMIPMHSS=20,0
Note: Set value to 20, 0
OK
Note: Command is valid
Set MN-AAA Shared Secrets $QCMIPMASSX
Description: This command is used to set MN-AAA shared secret for the currently active profile in HEX.
Values:
<HEX> Hex value from 0 to FFFFFFFF
<Val>
0: Do not commit to NV
1: Commit to NV
Note: If the value provisioned is not committed to NV, the temporary value will be deleted at
the end of the following call if $QCMIPP is called.
Syntax:
Command syntax: AT$QCMIPMASSX =<HEX>,<Val>
Command
AT$QCMIPMASSX?
Note: Display the current setting
Possible Responses
$QCMIPMASSX: Set
OK
Note: Command is valid
$QCMIPMASSX: (0-FFFFFFFF),(0-1)
OK
AT$QCMIPMASSX=?
Note: Display the range of values
Note: Command is valid
AT$QCMIPMASSX=FF,0
OK
Note: Set value to 0xFF, but not commit
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
162
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Set MN-HA Shared Secrets $QCMIPMHSSX
Description:
This command is used to set MN-HA shared secret for the currently active profile in HEX.
Values:
<HEX> Hex value from 0 to FFFFFFFF
<Val>
0: Do not commit to NV
1: Commit to NV
Note: If the value provisioned is not committed to NV, the temporary value will be deleted at
the end of the following call if $QCMIPP is called.
Syntax:
Command syntax: AT$QCMIPMHSSX =<HEX>,<Val>
Command
Possible Responses
$QCMIPMHSSX: Set
OK
AT$QCMIPMHSSX?
Note: Display the current setting
Note: Command is valid
$QCMIPMHSSX: (0-FFFFFFFF),(0-1)
OK
AT$QCMIPMHSSX=?
Note: Display the range of values
Note: Command is valid
AT$QCMIPMHSSX=FF,0
OK
Note: Set value to 0xFF, but not commit
Note: Command is valid
Set MN-AAA Shared Secrets $QCMIPMASPI
Description: This command is used to set MN-AAA SPIs for the currently active profile.
Values:
<SPI> SPI value from 0 to 4294967295
<Val>
0: Do not commit to NV
1: Commit to NV
Note: If the value provisioned is not committed to NV, the temporary value will be deleted if
the modem is power cycled or if the $QCMIPP command is used.
Syntax:
Command syntax: AT$QCMIPMASPI =<SPI>,<Val>
Command
Possible Responses
$QCMIPMASPI: 1234,1
OK
AT$QCMIPMASPI?
Note: Display the current setting
Note: Command is valid
$QCMIPMASPI: (0-4294967295),(0-1)
OK
AT$QCMIPMASPI=?
Note: Display the range of values
Note: Command is valid
AT$QCMIPMASPI=2300,0
Note: Set value to 2300, but not
commit
OK
Note: Command is valid
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
163
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Set MN-HA Shared Secrets $QCMIPMHSPI
Description: This command is used to set MN-HA SPIs for the currently active profile. Two arguments –
SPI value and one of the values: 0 and 1.
Values:
<SPI> SPI value from 0 to 4294967295
<Val>
0: Do not commit to NV
1: Commit to NV
Note: If the value provisioned is not committed to NV, the temporary value will be deleted if
the modem is power cycled or if the $QCMIPP command is used.
Syntax:
Command syntax: AT$QCMIPMHSPI =<SPI>,<Val>
Command
Possible Responses
$QCMIPMHSPI: 1234,1
OK
AT$QCMIPMHSPI?
Note: Display the current setting
Note: Command is valid
$QCMIPMHSPI: (0-4294967295),(0-1)
OK
AT$QCMIPMHSPI=?
Note: Display the range of values
Note: Command is valid
AT$QCMIPMHSPI=5500,0
OK
Note: Set value to 5500, but not commit
Note: Command is valid
Set Primary HA IP Address $QCMIPPHA
Description: This command is used to set the primary HA address of the mobile for the currently active
profile. The command takes two arguments, a string corresponding to the IP address of the
HA to be stored and a number (either 0 or 1) indicating whether or not to commit this value
to NV. The IP address should be formatted in standard dotted-decimal notation, e.g.
“10.1.1.20”.
Values:
<IP> IP address in standard dotted-decimal notation, e.g. “10.1.1.20”.
<Val>
0: Do not commit to NV
1: Commit to NV
Note: If the value provisioned is not committed to NV, the temporary value will be deleted if
the modem is power cycled or if the $QCMIPP command is used.
Syntax:
Command syntax: AT$QCMIPPHA =<IP>,<Val>
Command
Possible Responses
AT$QCMIPPHA?
$QCMIPPHA: 10.1.1.20, 0
Note: Display the current setting.
OK
AT$QCMIPPHA =?
$QCMIPPHA: ((0-255).(0-255).(0-255).(0-
Note: Display the range of values.
255)),(0-1)
OK
AT$QCMIPPHA =10.1.2.15,1
OK
Note: Set to 10.1.2.15, and commit to NV.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
164
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 19 – Qualcomm Defined AT Commands for CDMA Operation
Set Secondary HA IP Address $QCMIPSHA
Description: This command is used to set the secondary HA address of the mobile for the currently active
profile. The command takes two arguments, a string corresponding to the IP address of the
HA to be stored and a number (either 0 or 1) indicating whether or not to commit this value
to NV. The IP address should be formatted in standard dotted-decimal notation, e.g.
“10.1.1.20”.
Values:
<IP> IP address in standard dotted-decimal notation, e.g. “10.1.1.20”.
<Val>
0: Do not commit to NV
1: Commit to NV
Note: If the value provisioned is not committed to NV, the temporary value will be deleted if
the modem is power cycled or if the $QCMIPP command is used.
Syntax:
Command syntax: AT$QCMIPSHA =<IP>,<Val>
Command
Possible Responses
AT$QCMIPSHA?
$QCMIPSHA: 10.1.1.20, 0
Note: Display the current setting.
OK
AT$QCMIPSHA =?
$QCMIPSHA: ((0-255).(0-255).(0-255).(0-255)),(0-1)
Note: Display the range of values.
AT$QCMIPSHA =10.1.2.15,1
Note: Set to 10.1.2.15, and commit to NV.
OK
OK
Set Home HA IP Address $QCMIPHA
Description: This command is used to set the home HA address of the mobile for the currently active
profile. The command takes two arguments, a string corresponding to the IP address of the
HA to be stored and a number (either 0 or 1) indicating whether or not to commit this value
to NV. The IP address should be formatted in standard dotted-decimal notation, e.g.
“10.1.1.20”.
Values:
<IP> IP address in standard dotted-decimal notation, e.g. “10.1.1.20”.
<Val>
0: Do not commit to NV
1: Commit to NV
Note: If the value provisioned is not committed to NV, the temporary value will be deleted if
the modem is power cycled or if the $QCMIPP command is used.
Syntax:
Command syntax: AT$QCMIPHA =<IP>,<Val>
Command
Possible Responses
AT$QCMIPHA?
$QCMIPHA: 10.1.1.20, 0
Note: Display the current setting.
OK
AT$QCMIPHA =?
$QCMIPHA: ((0-255).(0-255).(0-255).(0-255)),(0-1)
Note: Display the range of values.
AT$QCMIPHA =10.1.2.15,1
Note: Set to 10.1.2.15, and commit to NV.
OK
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
165
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 20 – Reference Information
CHAPTER 20 - REFERENCE INFORMATION
MS Error Result Code : +CME ERROR: <error>
<error>
3
Meaning
Operation not allowed
Resulting from the following commands
All GSM 07.07 commands (+CME
ERROR: 3)
4
5
Operation not supported
All GSM 07.07 commands (+CME
ERROR: 4)
All GSM 07.07 commands (+CME
ERROR: 5)
PH-SIM PIN required (SIM lock)
10
UIM not inserted
+CPIN
11
12
13
UIM PIN1 required
UIM PUK1 required
UIM failure
+CPIN
+CPIN, +CPIN2
+CPIN, +CPIN2
14-15
16
17
18
20
21
22
23,25
24
26
Reserved
UIM wrong password
UIM PIN2 required
UIM PUK2 required
Phone Book full
Invalid Index for Phone Book
Phone Book entry not found
Reserved
Text string too long
Dial string too long
No network service
Reserved
+CPIN, +CPIN2
+CPIN, +CPIN2
+CPIN, +CPIN2
+CPBF, +CPBW
+CPBF
+CPBF, +CPBP
30
31-39
40
Network personalization PIN required (Network lock)
All GSM 07.07 commands (+CME
ERROR: 40)
41
Software resource not available
For example:
+WPRV, +CICB, +WFSH, +CCFC,
+WNAM, +COPS, +WRMP, +WPRL
All commands
42
43
44
Invalid parameter
Non-Volatile Memory failure
Invalid WPIN code or WPIN required
Invalid WSPC provisioning code
All commands
All commands except ATD
+WSPC, +WMDN, +WIMI, +WSID,
+WAOC, +WSCI, +WBGP, +WBGS,
+WPDS, +WCMT
WMDN, +WSCI, +WBGP, +WBGS,
+WPDS
45
46
OTKSL provisioning code access restricted +
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
166
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 20 – Reference Information
Message Service Failure Result Code: +CMS ERROR :<error>
<error>
1 to 127
301
Meaning
Reserved
Reserved
Resulting from the Following Commands
302
Operation not allowed
All SMS commands (+CMSS, +CMGL,
+CPMS…
303
Reserved
304
305
310-318
321
322
Invalid mode parameter
Invalid text mode parameter
Reserved
Invalid memory index
Reserved
+CMGS, +CMGW
+CMGS, +CMGW, +CMSS
+CMGR, +CMSS, +CMGD
330
Reserved
340
341
No +CNMA acknowledgement expected
Non Volatile Memory failure
+CNMA
All SMS commands
Specific Error Result Codes
<error>
500
Meaning
Resulting from the Following Commands
All commands
unknown error.
512
Reserved
513
514-518
519
Lower layer failure (for SMS)
Reserved
Reset the product to activate or change a
new echo cancellation echo.
+CMGS, +CMSS (+CMS ERROR: 513)
+ECHO, +VIP
Extended Error Report (+CEER) Call Processing Codes
Cause Value
Diagnostic
0
No error detected in call processing
No CDMA service detected
Modem is in a call, operation not allowed
Modem is not in a call, operation not allowed
Modem is in an unknown call state
Call Barring is ON
1
2
3
4
5
6
Invalid or Not allowed CDMA Service Option
Invalid Parameter
7
8
Operation only allowed during an incoming call
Invalid Mode Selection
9
10
11
Invalid Roam Selection
Invalid Band Selection
Final Result Codes
Verbose Result Code
+CME ERROR: <err>
+CMS ERROR: <err>
BUSY
Numeric (V0 set)
Description
As verbose
Error from GSM 07.05 commands
Error from SMS commands (07.07)
Busy signal detected
As verbose
7
4
8
3
0
2
ERROR
Command not accepted
NO ANSWER
NO CARRIER
OK
Connection completion timeout
Connection terminated
Acknowledges correct execution of a command line
Incoming call signal from network
RING
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
167
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 20 – Reference Information
Intermediate Result Codes
Verbose Result Code
+COLP :<number>,<type>
+CR : <type>
Numeric (V0 set)
Description
as verbose
Outgoing Call Presentation
as verbose
Outgoing Call report control
Local TA-TE data rate
+ILRR: <rate>
as verbose
CONNECT 300
10
Data connection at 300 bauds
Data connection at 1200 bauds
Data connection at 1200/75 bauds
Data connection at 2400 bauds
Data connection at 4800 bauds
Data connection at 9600 bauds
Data connection at 14400 bauds
CONNECT 1200
11
CONNECT 1200/75
CONNECT 2400
12
13
CONNECT 4800
14
CONNECT 9600
15
CONNECT 14400
+CSSI: <code1>[,<index>]
16
As verbose
Supplementary service notification
during a call setup
Parameters Storage
Command
General commands
+CSCS
AT&W
Enter to Save
AT&F
Default Values
X
X
X CDMA
X 0
1
+CMEE
+CRSL
+WIND
X
X
X
RUIM: 9; TE:8
Call Control Commands
%D
X 0
ATS0
+CICB
+CSNS
+VGR
+VGT
+SPEAKER
+ECHO
X
X
X
X
X
X
X
X
X
X 2
X
X 3
X 2
X 1
5
0 no auto answer
X
+SIDET
X
Network Commands
+COPS
X
X
X
X
X
0,0
6,4
(n,0 mode)
+CREG
SMS Commands
+CSDH
+WUSS
+WSCL
X 0
X 0
0
X RUIM:
X
Supplementary Service Commands
+CLIP
X
X 1
Data Commands
+CRC
+DS
+DR
X
X
X
X 0
X
X 0
Fax Class 2 Commands
+FCQ
+FCR
+IPR
+ICF
X
X
X
X
X
X
X
115200
3,3
2,2
+IFC
V24-V25 Commands
E
&C
&D
X
X
X
1
2
2
Phonebook
+WAIP
X
1
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
168
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 20 – Reference Information
Codes for SMS-STATUS-REPORT (+CDS and +CMGR)
Code
Meaning
Network Problems (IS-41D)
0
Address vacant
1
Address translation failure
Network resource shortage
Network failure
2
3
4
Invalid Teleservice id
Other Network Problem
5
Terminal Problems (IS-41D)
32
No page response
33
Destination busy
34
No acknowledgment
35
Destination resource shortage
SMS delivery postponed
Destination out of resources
36
37
38
Destination no longer at this address
Other terminal problem
39
Radio Interface Problems (IS-41D)
64
Radio IF resource shortage
Radio IF incompatible
65
66
Other Radio IF problem
General problems (IS-41D)
96
Unexpected parameter size
SMS Origination denied
SMS Termination denied
Supplementary service not supported
SMS not supported
97
98
99
100
101
Reserved
102
Missing expected parameters
Missing mandatory parameters
Unrecognized parameter value
Unexpected parameter value
User data size error
103
104
105
106
107
Other General problems
General Codes (Not defined in IS-41D)
32768
SMS OK. Message successfully delivered to base station
32769
32770
32771
32772
Waiting for transport layer acknowledgment
Out of resources (e.g. out of memory buffer)
Message too large to be sent over access channel
Message too large to be sent over data traffic channel
Code Meaning
32773
32774
32775
32776
32777
Network not ready
Phone not ready
Cannot send message in analog mode
Cannot send broadcast message
Invalid transaction id
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
169
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 20 – Reference Information
AT Commands Supported When SIM Card Removed
The following lists the AT commands that are supported in a RUIM modem (the modem needs a SIM card to
operate) when the SIM card is not present.
# List
1
2
3
4
AT Command
+IPR
+CMEE
+CCLK
+CBC
Note and Explanation
Set modem fixed baud rate
Display the error code
Clock management
Battery charge
5
6
7
8
+WIND
ATE
General status indication
Set modem local echo
Modem Offline mode
Reset the modem
Manufacturer identification
Model identification
Revision identification
Electronic serial dumber
TE character set selection
Phone activity status
Ring melody playback
Ringer sound level
+CPOF
+CFUN
+WGMI
+WGMM
+CGMR
+CGSN
+CSCS
+CPAS
+CRMP
+CRSL
+CSQ
9
10
11
12
13
14
15
16
17
18
19
20
Signal quality
+CREG
$QCDMG
ATIx
Network registration and roaming
Transition to diagnostics monitor
Request Modem Information (x = 0-7)
AT Commands for AMPS Operation
In the APMS mode, only the voice call is applicable. Although user can still issue almost all of AT
commands, the most of the AT commands are not applicable for AMPS operation, e.g. data commands,
SMS, FAX, RUIM commands, service programming etc.
The following table list the AT commands that are meaningful for AMPS operation. Please note that these
listed AT commands are also applicable in CDMA operations.
# List
1
2
AT command
+COPS
ATD
Note and Explanation
+COPS=2,n (n=0,1)
Making a voice call
3
ATA
Answer a voice call
4
ATDL
Redial last #
5
6
7
8
+VGR
+VGT
+CMUT
A/
Change the receiving voice volume
Change the transmitting voice volume
Mute the microphone
Repeat last command
Set auto answer
9
ATS0
10
11
12
13
14
15
16
17
18
ATH
ATIx
+IPR
+CNUM
+CGSN
+CMEE
+WPRL
+CPOF
+CFUN
Hang up a voice call
Request Modem Information (x = 0-7)
Set modem baud rate
Display modem directory #
Display modem ESN # (in hex format)
Display the error code
Read the PRL version
Modem OFF mode
Reset the modem
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
170
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 21 – AT Command Examples
CHAPTER 21 - AT COMMAND EXAMPLES
This chapter gives illustrative examples of general AT command usage.
Example 1: When the MS Has Already Been Powered On.
AT+CMEE=1
OK
Enable the reporting of mobile equipment errors
AT+CPAS
+CPAS: 0
OK
Get the MS Status
MS is ready to receive commands
Examples Where a Voice Call is Originated.
Example 3:
When the MS is powered on.
AT+CMEE=1
Enable the reporting of mobile equipment errors
OK
ATD18001234567;
OK ATD
Make a voice call
Command is being processed
+WORG:18001234567
+WCNT:3
Indication of call origination sent to the Base Station with dialing string 18001234567
Call Connected with CDMA Service Option 3, Traffic channel established.
Conversation…
ATH
Release the call
OK ATH
+WEND:10
Command is being processed
Call Ended, end reason 10 (Normal Release).
Example with Incoming Calls
When the MS is Powered On.
AT+CMEE=1
OK
Enable the reporting of mobile equipment errors
AT+WIND=63
OK
AT+CLIP=1
OK
Ask to display the general indications.
Enable the calling line identification presentation.
Query own number.
AT+CNUM
+CNUM: “Phone”,”8585551212”,129
OK
Call the Number from Another MS.
+RING
Incoming Call.
+CLIP: "8585551212",129
ATA
Identification of the remote party.
Answer the call.
OK ATA
Command is being processed.
+WANS
Call has been answered.
+WCNT:3
Call Connected with CDMA Service Option 3, Traffic channel established.
…Conversation…
+WEND:6
Call Ended, end reason 6 (Normal Release), the call has been released by the remote party.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
171
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 21 – AT Command Examples
Example of a Call Waiting Situation
When the MS is Powered On.
AT+CMEE=1
OK
Enable the reporting of mobile equipment errors
ATD8585551212;
OK
Make a voice call
ATD Command is being processed
+WORG:8585551212
+WCNT:3
Indication of call origination sent to the Base Station with dialing string 18001234567
Call Connected with CDMA Service Option 3, Traffic channel established.
Conversation…
Conversation with first call.
+CCWA:”8582701234”,129
AT+WFSH
OK
Indication of another incoming call. You will also hear a beep sound in the earpiece.
Send a flash to the Base Station (toggle to the second call).
AT command is being executed.
+WFSH
Flash sent to the Base Station. Call switches to the second call. However, this is not 100%
guaranteed because the there is no confirmation from the Base Station.
Conversation…
Conversation with second call.
Repeat as Necessary
ATH
OK
+WEND:10
Release the all calls.
ATH command is being executed.
Calls End
Examples About Short Messages
Example 1: Receive a Short Message
AT+CNMI=2,1,1,1,0
OK
SMS-DELIVERs are stored in NV, SMS-STATUS-REPORTs are routed to TE
+CMTI:"MT",0
New message received. Message store in “MT” memory at index 0.
SMS-DELIVERs are routed to TE
AT+CNMI=2,2,1,1,0
+CMT:"8585551212","02/05/17,10 :43 :07",129,1,2,0,”5550000”,17
Test SMS Message
Received message.
AT+CNMA
OK
Acknowledge the received message to the network.
Example 2: Send a Short Message
AT+CNMI=2,1,1,1,0
OK
SMS-DELIVERs are stored in NV, SMS-STATUS-REPORTs are routed to TE
AT+CMGS=”8585551212”
Send a SMS-SUBMIT to mobile phone
Product sends a 4 characters sequence: 0x0D 0x0A 0x3E 0x20
This is the first text line
This is the last text line
+CMGS: 1
Edit first line and press carriage return (<CR>, 0x0D)
Edit last line and send message by pressing <ctrl-Z> (0x1A)
Success: message reference 1 is returned from the SMS Service Center
+CDS:2,1,"8582431439",129,"02/05/17,10 :14 :17","02/05/17,10 :14 :27",32768
Success: report of successful message delivery received. Time of sending of the message
and receiving of the acknowledgment from the SMS Service Center is reported, along with
the status code.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
172
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 21 – AT Command Examples
Example 2: Send a Short Message by a Selected Language and a Coding Format
AT+CNMI=2,1,1,1,0
OK
SMS-DELIVERs are stored in NV, SMS-STATUS-REPORTs are routed to TE
AT+WSCL=6,4
Select SMS in Chinese language and with Unicode format
AT+CMGS=”8585551212”
Send a SMS-SUBMIT to mobile phone
Product sends a 4 characters sequence: 0x0D 0x0A 0x3E 0x20
Chinese characters in Unicode
This is the last message line
Edit first line and press carriage return (<CR>, 0x0D)
The SMS will be sent when passer see <ctrl-Z> (0x001A)
+CMGS: 1
Success: message reference 1 is returned from the SMS Service Center
+CDS:2,1,"8585551212",129,"02/05/17,10 :14 :17","02/05/17,10 :14 :27",129,18,6,4
Success: report of successful message delivery received. Time of sending of the message
and receiving of the acknowledgment from the SMS Service Center is reported, along with
the status code.
Example 3: Send a Short Message by a Selected Priority and with Call Back Number
AT+CNMI=2,1,1,1,0
OK
SMS-DELIVERs are stored in NV, SMS-STATUS-REPORTs are routed to TE
AT+WSCL=6,4
Select SMS in Chinese language and with Unicode format
AT+CMGW=”8585551212”,20,2,”2345678901”
write an SMS to store in mobile phone with 20 characters, priority 2 and the call back
number “2345678901”
Chinese characters in Unicode
This is the last message line
The SMS will be stored when 20 characters are entered
+CMGW: 0
AT+CMSS=0
+CMSS:1
OK
The SMS is stored in the first location of the SIM card
Send the SMS from location index 0
+CDS:2,1,"8582431437",129,"03/04/11,14 :10 :56","03/04/11,14 :11 :02",32768
Example 3: Read Short Messages
AT+CPMS=”MT”
OK
Set Mobile Terminated as preferred memory storage
+CPMS:2,10,1,10
Currently there are 2 MT messages and 1 MO messages stored.
List all stored messages
AT+CMGL=”ALL”
OK
+CMGL:0,"REC READ","8585551111", 1,2,15
Test message #1
+CMGL:1,"REC UNREAD","8585552222",1,2,15
Test message #2
+CMGL:0,"STO UNSENT","8585551212",1,2,24
Test message to be sent.
AT+CMGR
=1 Read the first message in currently selected memory
OK storage (previously set by AT+CPMS).
+CMGR:"REC UNREAD","8585552222","02/05/15,15 :54 :04",1,2,0,”5550000”,15
Test message #2
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
173
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
CHAPTER 22 - VERIZON® SPECIFIC AT COMMANDS
This chapter details AT commands that are Verizon® specific. The detail presented in this chapter should
replace the referenced section in the main document.
SMS Status Report Indication Directly Displayed +CDS
(Chapter 3)
Description: This response indicates an SMS status report has been received and according to the
message storage preferences (+CNMI), is to be directly displayed. +CDS is also used in the
data compression functionality as an active command. Refer to Chapter 17 for an
explanation of +CDS usage for data compression.
For Verizon®, the +CDS response has a secondary format that is used to indicate that a
SMS message was delivered to the recipient (SMS message delivery ACK on). This form of
the +CDS message is not stored in NV memory. In the case of delivery acknowledgement,
the +CNMI setting will not have an effect and delivery acknowledgements will always be
reported with the +CDS response.
Values:
<ind>: Message type indicator
0 - Status report
1 – MO delivery acknowledge message
<mr>: Message Reference
<ra>: Recipient Address
<tora>: Type-of-Address of <ra>
<scts>: Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
<dt>: Discharge Time in string format: “yy/MM/dd,hh :mm :ss±zz” (Year [00-99], Month [01-
12], Day [01-31], Hour, Minute, Second and Time Zone [quarters of an hour])
<st>: Status of a SMS-STATUS-REPORT (See chapter 20)
<msg id>: Message reference. The Id of the sent message.
“<date>,<time>”: Timestamp of the acknowledge receipt.
<delivery ack body>: MO message delivery acknowledgment.
Syntax:
Response Syntax: +CDS: <ind>, <mr>, [<ra>], [<tora>], <scts>, <dt>, <st> (Text mode)
+CDS: <ind>, <msg id>,”<date>,<time>”,<delivery ack body>
Example Result
+CDS: 0, 2, 116, ”3146290800”, 129, “98/10/01,12 :30 :07+04”, “98/10/01 12 :30 :08+04”, 0
Note: SMS status report received
+CDS: 1, 3, "03/09/11,14 :52 :53", Message to 8582431438 delivered
Note: SMS acknowledge report received. "Message to 8582431438 delivered" is the ack message
body.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
174
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Incoming Message Directly Displayed +CMT (Chapter 3)
Description: This response indicates that an incoming message has been received and according to the
message storage preferences (+CNMI), is to be directly displayed.
Values:
<oa> Originator Address. <oa> will be displayed only if the message <privacy> value is
normal (0).
<scts> Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
<tooa> Type-of-Address of <oa>
<lang> Language
<encod> Encoding method
<priority>: Message priority:
0 – Normal
1 – Interactive
2 – Urgent
3 – Emergency
<cbn> Call Back Number
<length> The number of characters in the following <data> field
<data> Message contents
Syntax:
Response syntax: +CMT: <oa>, <scts>, <tooa>, <lang>, <encod>, <priority> [,<cbn>],
<length> <CR><LF> <data> (text mode)
Example Result
+CMT: “123456”,”98/10/01,12 :3000+00”,129,1,2,0,”5550000”,5<CR><LF>
Hello
Note: Incoming message received
Roaming Indication +WROM (Chapter 3)
Description: This response indicates that the roaming status has changed.
Syntax:
Response Syntax: +WROM: <roam>
Command
Possible Responses
+WROM:1
<roam>
0: Roam Icon On (affiliated network)
1: Roam Icon Off (Home)
2: Roam Icon Blink (foreign network)
The following values apply to enhanced roaming:
3: Out of Neighborhood
4: Out of Building
5: Roaming - Preferred System
6: Roaming - Available System
7: Roaming - Alliance Partner
8: Roaming - Premium Partner
9: Roaming - Full Service Functionality
10: Roaming - Partial Service Functionality
11: Roaming Banner On
12: Roaming Banner Off
13 – 63: Reserved for Standard Enhanced Roaming Indicator Numbers
64 – 93: Enhanced Roaming Indicator (+WERI response)
94 - 255: Reserved
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
175
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Enhanced Roaming Indication +WERI
Description: This response indicates that the enhanced roaming status has changed.
Syntax:
Response Syntax: +WERI: <indicator>, <icon image>, <icon mode>, <call prompt>,
<alert/call id>,
<chari type>, <text>
Command
Possible Responses
Note: Example of acquiring service with enhanced roaming.
+WERI: 69,2,0,0,4,2,”Extended Network”
+WROM:2
Note: Both +WERI and +WROM responses.
Note: Example of acquiring service without enhanced
roaming.
+WROM:1
Note: No +WERI response.
<indicator>
64-93: Index number identifying the roaming indicator entry.
<icon image>
0-15: Verizon®. defined value that specifies the Icon Image that is displayed.
<icon mode>
0-3: Verizon®. defined value that specifies how the Icon Image is displayed (On, Off,
Flashing).
<call prompt>
0-3: Verizon®. defined value that identifies the Call Prompt that is displayed for each
roaming indicator. This field is set to a value of ZERO when no call prompt is used. Note
that this field is currently not implemented in the Verizon®. user interface specs. It may
be used in the future.
<alert/call id>
0-7: Verizon®. defined value that identifies the Alert Sound that is used for the indicator.
The value in this field reflects the ID of the Alert Sound that the mobile annunciates to
the end user.
<chari type>
0-31: Character Encoding Type (Ref TSB58E table 9.1-1). Identifies the character code
table used for the <text> field. (Usually set to 2.)
Type
Bit Length
Character Encoding
0
8 Octet,
unspecified
1
2
3
4
see IS-91
7
7
16
IS-91 Extended Protocol Message
7-bit ASCII (ANSI x3.4)
IA5 (Table 11 of ITU-T T.50)
UNICODE (ISO/IEC 10646-1:1993)
Shift-JIS
5
8 or 16
6
7
8
9
8 or 16
Korean (KS x 1001:1998)
Latin/Hebrew (ISO 8859-8:1988)
Latin (ISO 8859-8:1988)
GSM 7-bit default alphabet
Reserved
8
8
7
x
10-31
<text>
Verizon®. defined variable length field that contains the text data used for the banner.
The text is in the format specified in the Character Encoding Type. The text field is
limited to a 32 character maximum length.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
176
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Emergency Mode +WSOS (Chapter 3)
Description: This unsolicited command indicates a change in the status of Emergency Mode has taken
place. In the event that Emergency Mode is entered as the result of an emergency call, this
response will be sent to indicate that the modem is now in emergency mode. After this point,
to exit the modem out of Emergency Mode, an AT+WSOS or AT+COPS command must be
sent, which will result in a +WSOS response to confirm that Emergency Mode has been
exited. See +WSOS, section for more information about Emergency Mode.
Values:
The parameters values are the following ones:
<flag>
0: Emergency Mode Exited
1: Emergency Mode Entered
For Verizon®. releases, the +WSOS:0 result code will also be sent to indicate that
emergency mode has been exited in the following cases:
•
After an emergency call is released and five minutes have passed without another
emergency call.
•
After an emergency call is released and the user dials a non-emergency number.
Syntax:
Response Syntax: +WSOS: <flag>
Command
Possible Responses
ATD911;
OK
Note: Make emergency call
+WSOS:1
+WORG:911
Note: Unsolicited +WSOS result confirms Emergency Mode is entered
AT+WSOS
OK
Note: Exit Emergency Mode
+WSOS:0
Note: Unsolicited +WSOS result confirms Emergency Mode is exited
AT+COPS=0,0
OK
Note: While in Emergency Mode,
the mode preference is changed,
resulting in Emergency Mode
being exited
+WSOS:0
+COPS:0,0
Note: Unsolicited +WSOS result confirms emergency mode exited and
unsolicited +COPS result confirms Automatic mode is requested
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
177
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Read message +CMGR (Chapter 8)
Description: This command allows the application to read stored messages. The messages are read
from the memory selected by +CPMS command. A message read with status “REC
UNREAD” will be updated in memory with the status “REC READ”.
Note: The <stat> parameter for SMS Status Reports is always “READ”.
Values:
tat> Status of message in memory. Possible values are as follows:
Possible Values
“UREAD”
“READ”
Status of Messages in Memory
received unread messages
received read messages
stored unsent messages
stored sent messages
all messages
“USENT”
“SENT”
“ALL”
Note: For SMS Status Reports, only “ALL” and “READ” values of the <stat> parameter will
list messages ; other values will only return OK.
<oa/da>: Origination/destination address value in string format. <od/da> will be displayed
only if the message <privacy> value is 0 (Normal).
<mr>: Message Reference
<scts>: Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
<dt>: Discharge Time in string format: “yy/MM/dd,hh :mm :ss±zz” (Year [00-99], Month [01-
12], Day [01-31], Hour, Minute, Second and Time Zone [quarters of an hour] )
<st>: Status of a SMS-STATUS-REPORT (See Chapter 20)
<lang>: Language
<encod>: Encoding
<priority>: Message priority:
0 – Normal
1 – Interactive
2 – Urgent
3 – Emergency
<privacy>: Message privacy:
0 – Normal
1 – Restricted
2 – Confidential
3 – Secret
<reply>: Message reply option:
0 – No Acknowledge
1 – Delivery Acknowledge
<cbn>: Call Back Number
<length>: Length of the text message (in bytes).
<data>: Message text
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
178
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Syntax:
Command syntax: AT+CMGR=<index>
Response syntax: +CMGR :<stat> [,<oa>], <scts>, <lang>, <encod>, <priority>, <privacy>,
<reply> [,<cbn>], <length> <CR><LF> <data> (for SMS-DELIVER only)
+CMGR: <stat> [,<da>], <dt>, <lang>, <encod>, <priority>, <privacy>, <reply>, <cbn>],
<length> <CR><LF> <data> (for SMS-SUBMIT only)
+CMGR: <stat>,<mr>,<scts>,<dt>,<st> (for SMS-STATUS-REPORT only)
Command
Possible Responses
+CMTI: “MT”,1
Note: New message received
AT+CMGR=1
+CMGR: “REC UNREAD”,”8585551212”, ”98/10/01,18
Note: Read the message
:22 :11+00”,1,2,0,0,0,”8585550000”,9<CR><LF>
ABCdefGHI
OK
AT+CMGR=1
+CMGR: “REC READ”,”8585551212”, ”98/10/01,18 :22
Note: Read the message again
:11”,1,2,0,0,0,”8585550000”,9<CR><LF>
ABCdefGHI
OK
Note: Message is read now
+CMS ERROR: 321
Note: Error : invalid index
+CPMS:0,10,0,10
OK
AT+CMGR=2
Note: Read at a wrong index
AT+CPMS=”SR”;+CNMI=,,,2
Note: Reset to text mode, set read
memory to “SR”, and allow storage
of further SMS Status Report into
“SR” memory
AT+CMSS=3
Note: Send an SMS previously
stored
+CMSS: 160
OK
+CDSI: “SR”,1
Note: New SMS Status Report stored in “SR” memory at
index 1
AT+CMGR=1
Note: Read the SMS Status Report
+CMGR: “READ”,160,
“8585551212”,129,”01/05/31,15:15:09”,
“01/05/31,15:15:09”,0
OK
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
179
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
List Message +CMGL (Chapter 8)
Description: This command allows the application to read stored messages, by indicating the type of the
message to read. The messages are read from the memory selected by the +CPMS
command.
Values:
<index>: Place of storage in memory.
<stat>: Possible values, the status of messages in memory, are as follows:
Possible Values
“UREAD”
“READ”
“USENT”
“SENT”
Status of Messages in Memory
received unread messages
received read messages
stored unsent messages
stored sent messages
all messages
“ALL”
Note: For SMS Status Reports, only “ALL” and “READ” values of the <stat> parameter will
list messages; other values will only return OK.
<oa/da> : Origination/destination address value in string format. <od/da> will be displayed
only if the message <privacy> value is 0 (Normal).
<fo>: First Octet, coded like SMS-SUBMIT first octet in document [4], default value is 17 for
SMS-SUBMIT
<mr>: Message Reference
<dt>: Discharge Time in string format: “yy/MM/dd,hh :mm :ss±zz” (Year [00-99], Month [01-
12], Day [01-31], Hour, Minute, Second and Time Zone [quarters of an hour] )
<st>: Status of a SMS-STATUS-REPORT
<lang>: Language
<encod>: Encoding
<length> : Length of the text message (in bytes).
<data>: Message text
Syntax:
Command syntax: AT+CMGL=<stat>
Response syntax: +CMGL : <index>,<stat>,<da/oa>,<lang>,
<encod>,<length><CR><LF><data> (for SMS-DELIVER and SMS-SUBMIT, may be
followed by other <CR><LF>+CMGL:<index>…)
+CMGL: <index>,<stat>,<fo>,<mr>,<scts>,<dt>,<st> (for SMS-STATUS-REPORT only, may
be followed by other <CR><LF>+CMGL:<index>…)
Command
Possible Responses
AT+CMGL=“UREAD”
Note: List unread
messages in text mode
+CMGL: 1,”REC
UNREAD”,”8585551212”,1,2,15
<CR><LF>Unread message!
+CMGL: 3,”REC UNREAD”, “8585551212”, 1,2,5<CR><LF>Hello
OK
Another message unread!
Note: 2 messages are unread, these messages will then have their
status changed to “REC READ” (+CSDH:0)
AT+CMGL=”READ”
Note: List read messages
in text mode
+CMGL: 2,”REC READ”,”8585551212”,1,2,9
<CR><LF>
Keep cool
OK
AT+CMGL=”SENT”
Note: List stored and
sent messages in text
mode
OK
Note: No message found
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
180
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Send Message +CMGS (Chapter 8)
Description: The <da> field is the address of the terminal to which the message is sent. To send the text
message, type <ctrl-Z> (0x1A) as the final character of the message. This command can be
aborted using the <ESC> (0x1B) character while entering the message text.
The <length> parameter is optional, it is used to set the length of the text string. When
<length> is specified, the CMGS command will only process the number of bytes specified
by <length> regardless of whether it contains <ctrl-Z>, <ESC>, or <backspace> characters.
The <priority>, <privacy>, <reply option>, and <cbn> parameters are optional. When not
specified, they default as follows:
Priority: 0 (Normal)
Privacy: 0 (Normal)
Reply Option: 0 (No Acknowledge)
Call back number: Not included in the message.
Values:
<da> : Destination address value in string format.
<length> : Length of the text message (in bytes).
<priority>: Message priority:
0 – Normal
1 – Interactive
2 – Urgent
3 – Emergency
<privacy>: Message privacy:
0 – Normal
1 – Restricted
2 – Confidential
3 – Secret
<reply>: Message reply option:
0 – No Acknowledge
1 – Delivery Acknowledge
<cbn>: Call Back
Syntax:
Command syntax: AT+CMGS=<da> [,<length>] [,<priority>] [,<privacy>] [,<reply>] [,<cbn>]
<CR> entered text<ctrl-Z / ESC>
Command
Possible Responses
AT+CMGS=”8585551212”<CR>
Please call me soon, Fred. <ctrl-Z>
Note: Send a message
+CMGS:<mr>
OK
AT+CMGS=”8585551212”,12
Please call.<ctrl-Z>
+CMGS:<mr>
OK
Note: Send 12 byte message
AT+CMGS=”8585551212”,,2,1,1,”5550000”
Please call ASAP<ctrl-Z>
+CMGS:<mr>
OK
Note: Send a message with the specified priority, privacy, reply option and
call back number. Notice length field is omitted.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
181
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Write Message to Memory +CMGW (Chapter 8)
Description: This command stores a message in memory (SMS-SUBMIT). The memory location <index>
is returned (no choice possible as with phonebooks +CPBW). A text or Unicode message is
entered as described for the Send Message +CMGS command.
The <length> parameter is optional, it is used to set the length of the text string. When
<length> is specified, the CMGW command will only process the number of bytes specified
by <length> regardless of whether it contains <ctrl-Z>, <ESC>, or <backspace> characters.
The <priority>, <privacy>, <reply option>, and <cbn> parameters are optional. When not
specified, they default as follows:
Priority: 0 (Normal)
Privacy: 0 (Normal)
Reply Option: 0 (No Acknowledge)
Call back number: Not included in the message.
Values:
<oa/da> : Origination/destination address value in string format.
<length> : Length of the text message (in bytes).
<priority>: Message priority:
0 – Normal
1 – Interactive
2 – Urgent
3 – Emergency
<privacy>: Message privacy:
0 – Normal
1 – Restricted
2 – Confidential
3 – Secret
<reply>: Message reply option:
0 – No Acknowledge
1 – Delivery Acknowledge
<cbn>: Call Back Number
Syntax:
Command syntax: AT+CMGS= <oa/da> [,<length>] [,<priority>] [,<privacy>] [,<reply>]
[,<cbn>] <CR> entered text <ctrl-Z / ESC>
Response syntax: +CMGW: <index> or +CMS ERROR: <err> if writing fails
Command
Possible Responses
AT+CMGW=”8585551212”<CR>
Hello how are you ?<ctrl-Z>
Note: Write a message
+CMGW: 4
OK
Note: Message stored in
index 4
AT+CMGW=”8587777777”,6<CR>
¥IÅàø?<ctrl-Z>
+CMGW: <index>
OK
Note: Write a message with specified length of 6 bytes
Note: Message stored in
<index>
AT+CMGW=”8585551212”,,2,1,1,”5550000”
Please call ASAP<ctrl-Z>
+CMGW: 5
OK
Note: Write message with the specified priority, privacy, reply
option and call back number. Notice length field is omitted.
Note: Message stored in
index 5
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
182
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Service Programming Code +WSPC (Chapter 16)
Description: This command allows for entry of the service programming code (either MSL or OTKSL).
Upon successful entry of this code, all other service provisioning AT commands may be
used. If this code is not properly entered prior to attempting other provisioning AT
commands, all provisioning commands will return ERROR. If the OTKSL is used to enter
provisioning mode, only the +WIMI, +WMDN, and +WCMT commands will be allowed. All
other commands will return ERROR.
This command supports fifteen attempts to enter the correct service programming code. If
fifteen incorrect attempts are performed, the ME will report a message and go into offline
mode.
Once the correct SPC code is entered, the modem transitions to the Service Programming
state. This state is not exited until a commit is done (+WCMT). While in the Service
Programming state, subsequent validations of the SPC code are ignored until the Service
Programming state is reset.
Values:
Syntax:
<lock type>
0: OTKSL – One Time Key Subsidy Lock
1: MSL – Master Subsidy Lock
<code>
Six character programming code.
Command syntax: AT+WSPC=<lock type>,<code>
Command
AT+WSPC?
Possible Responses
ERROR
Note: Service programming code request
Note: Invalid request
AT+WSPC=?
ERROR
Note: Invalid request
ERROR
AT+WSPC=1,111111
Note: Enter service programming code 111111
Note: Code invalid
AT+WSPC=1,000000
OK
Note: Enter service programming code 000000
Note: Code valid
Verizon®. System Selection +WVSS
Description: This command is used to set the system selection and is persistent on reset. The values that
are available with the +WVSS command are dependent upon the currently loaded PRL.
Values:
<pref> Preferred only systems:
0: Home Only - Service on home systems
1: Automatic - Roaming allowed on affiliated systems
Non-preferred systems:
0: Home Only - Service on home systems
2: Automatic-A - Roaming allowed on affiliated systems and any A band system
3: Automatic-B - Roaming allowed on affiliated systems and any B band system
Syntax:
Syntax: +WVSS: <pref>
Command
Possible Responses
AT+WVSS=?
+WVSS: (0-3)
Note: Show supported parameters
OK
AT+WVSS?
+WVSS: 1
Note: Get current setting
AT+WVSS=0
OK
OK
Note: Set home only
Note: Home only mode set.
AT+WVSS=3
ERROR
Note: Set automatic-B mode
Note: Automatic-B mode not allowed
in preferred only service.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
183
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Initial Programming Required +WOT0
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that initial device
programming is required.
Syntax:
Response Syntax: +WOT0: “Initial programming required!”
Command
Possible Responses
+WOT0: “Initial programming required!”
Programming In Progress +WOT1
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that device
programming is in progress.
Syntax:
Response Syntax: +WOT1: “Programming in progress”
Command
Possible Responses
+WOT1: “Programming in progress”
Programming Successful +WOT2
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that device
programming has completed successfully. This response will be accompanied by three quick
audio tones from the speaker.
Syntax:
Response Syntax: +WOT2: “Programming Successful”
Command
Possible Responses
+WOT2: “Programming Successful”
Programming Unsuccessful +WOT3
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that device
programming has completed unsuccessfully. This response will be accompanied by three
quick audio tones from the speaker.
Syntax:
Response Syntax: +WOT3: “Programming Unsuccessful”
Command
Possible Responses
+WOT3: “Programming Unsuccessful”
Commit Successful +WOTC
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that the programmed
parameters have be successfully committed to NVRAM.
Syntax:
Response Syntax: +WOTC: “Commit Successful”
Command
Possible Responses
+WOTC: “Commit Successful”
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
184
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
SPL Unlocked +WOTS
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that the Software
Provisioning Lock is in the unlocked state.
Syntax:
Response Syntax: +WOTS: “SPL unlocked”
Command
Possible Responses
+WOTS: “SPL unlocked”
NAM Download Ok +WOTN
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that the NAM download
has completed successfully.
Syntax:
Response Syntax: +WOTN: “NAM Download OK”
Command
Possible Responses
+WOTN: “NAM Download OK”
MDM Download Ok +WOTM
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that the MDM
download has completed successfully.
Syntax:
Response Syntax: +WOTM: “MDM Download OK”
Command
Possible Responses
+WOTM: “MDM Download OK”
MSI Download Ok +WOTI
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that the IMSI download
has completed successfully.
Syntax:
Response Syntax: +WOTI: “IMSI Download OK”
Command
Possible Responses
+WOTI: “IMSI Download OK”
PRL Download Ok +WOTP
Description: This Over-The-Air Service Provisioning (OTASP) response indicates that the PRL download
has completed successfully.
Syntax:
Response Syntax: +WOTP: “PRL Download OK”
Command
Possible Responses
+WOTP: “PRL Download OK”
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
185
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 22 - Verizon® Specific AT Commands
Excess SPC Failures +WLCK
Description: This response indicates that 15 failed attempts have been made to enter the service
programming code. If the modem is not in emergency mode, any active call will be
terminated and the modem will go into offline mode.
Note: A successfully entered service programming code grants access to modem
configuration data.
Syntax:
Response Syntax: +WLCK: “Excess SPC failures!”
Command
Possible Responses
AT+WSPC=0,123456
Note: 15th attempt to enter the SPC.
+WLCK: “Excess SPC failures!”
Note: Modem now in offline mode.
Position Determination Lock Level +WPLCK
Description: This command specifies and returns the position determination lock setting. If the lock is set
to ‘lock all’, then only E911-related position determination events are allowed and all other
position determination requests are denied.
Values:
<level>
0: No lock (allow all)
1: Lock mobile initiated location services
2: Lock mobile terminated location services
3: Lock all
Syntax:
Command syntax: AT+WPLCK=<level>
Command
Possible Responses
AT+WPLCK=?
+WPLCK: (0-3)
Note: Display valid parameter range
OK
AT+WPLCK?
+WPLCK: 0
Note: Request current setting type
AT+WPLCK=3
OK
OK
Note: Select lock all
Note: Command successful
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
186
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
CHAPTER 23 - SPRINT® SPECIFIC AT COMMANDS
This chapter details AT commands that are Sprint® specific. The command presented in this chapter should
replace the corresponding general commands in the main document.
SMS Status Report Indication Directly Displayed +CDS
(Chapter 3)
Description: This response indicates an SMS status report has been received and according to the
message storage preferences (+CNMI), is to be directly displayed. +CDS is also used in the
data compression functionality as an active command. Refer to Chapter 17for an
explanation of +CDS usage for data compression.
For Sprint®, the +CDS response has a secondary format that is used to indicate that a SMS
message was delivered to the recipient (SMS message delivery ACK on). This form of the
+CDS message is not stored in NV memory. In the case of delivery acknowledgement, the
+CNMI setting will not have an effect and delivery acknowledgements will always be
reported with the +CDS response.
Values:
<ind>: Message type indicator
0 - Status report
1 – MO delivery acknowledge message
<mr>: Message Reference
<ra>: Recipient Address
<tora>: Type-of-Address of <ra>
<scts>: Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
<dt>: Discharge Time in string format: “yy/MM/dd,hh :mm :ss±zz” (Year [00-99], Month [01-
12], Day [01-31], Hour, Minute, Second and Time Zone [quarters of an hour])
<st>: Status of a SMS-STATUS-REPORT (See Chapter 20)
<msg id>: Message reference. The Id of the sent message.
“<date>,<time>”: Timestamp of the acknowledge receipt.
<delivery ack body>: MO message delivery acknowledgment.
Syntax:
Response Syntax:
+CDS: <ind>, <mr>, [<ra>], [<tora>], <scts>, <dt>, <st> (Text mode)
+CDS: <ind>, <msg id>,”<date>,<time>”,<delivery ack body>
Example Result
+CDS: 0, 2, 116, ”3146290800”, 129, “98/10/01,12 :30 :07+04”, “98/10/01 12 :30 :08+04”, 0
Note: SMS status report received
+CDS: 1, 3, "03/09/11,14 :52 :53", Message to 8582431438 delivered
Note: SMS acknowledge report received. "Message to 8582431438 delivered" is the ack message
body.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
187
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
Set Phone Functionality +CFUN
Description: This command selects the mobile station’s level of functionality. AT+CFUN=0 is equivalent
to AT+CPOF
The AT+CFUN=1 (by default, AT+CFUN will act the same as AT+CFUN=1) command
restarts the entire CDMA stack and CDMA functionality: a complete software reset is
performed. In addition, the OK response will be sent at the last baud rate defined by the
+IPR command.
If an emergency call is made in OFFLINE mode, the modem will reset and immediately after
boot, originate the emergency call. The functionality of +WSOS is unchanged.
Values:
Syntax:
<functionality level>
0: Set the phone to OFFLINE mode.
1: Set the phone to ONLINE mode and resets the phone.
Command syntax: AT+CFUN=<functionality level>
Command
Possible Responses
AT+CFUN?
+CFUN: 1
Note: Ask for current functionality level
OK
Note: Full functionality
AT+CFUN=0
OK
Note: Set phone offline
AT+CFUN=1
Note: Command valid
Note: Command valid
Note: Set phone ONLINE. A software reset is
performed.
Signal Quality +CSQ
Description: This command will return the raw RSSI data, raw Ec/Io, and the channel frame error rate.
Values:
<raw rssi>
75-105: valid value range in units of -dBm
255: represents an unknown signal quality
<raw Ec/lo>
0-15: valid value range in units of -dB
255: represents an unknown signal quality
<fer>:
0-100%: Traffic channel error rate
255: represents an unknown signal quality
Syntax:
Command syntax: AT+CSQ
Command
Possible Responses
AT+CSQ
+CSQ: <raw rssi>,<raw Ec/Io>,<fer>
OK
Note: <raw rssi>, <raw Ec/lo>, and <fer> as defined below
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
188
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
Facility Lock +CLCK
Description: This command is used by the application to lock, unlock, or interrogate an ME or network
facility <fac>. When changing a lock state, a password value must be included in the
command even though passwords are not currently enforced for these facilities. Any 4 digit
sequence can be entered for the password value.
This command is also used to allow control of the call barring supplementary service.
Barring calls or querying the status of call barring is possible for Data and Voice Calls,
except Emergency Voice Calls.
Values:
The following <fac> and <mode> values are supported:
“AO”: BAOC (Barr Outgoing Calls)
<mode>
0: Allow all outgoing calls
1: Allow outgoing calls only for phonebook entries (use ATD> command) and
emergency voice calls
2: Allow emergency voice calls only
9: Query status
“AI”: BAIC (Barr Incoming Calls)
<mode>
0: Allow all incoming calls
1: Allow incoming calls only for phonebook entries (match number in phonebook) and
emergency voice calls
2: Allow emergency voice calls only
9: Query status
Note: Setting this facility to 0 will force the “AO” facility to 0.
“PB”: BAMC (Barr Outgoing Phonebook Match Calls)
<mode>
0: Allow all outgoing calls
1: Allow outgoing calls only for phonebook entries
9: Query status
Note: Setting this facility to 0 will force the “AO” facility to 0.
“DT”: BADC (Barr Data Calls)
<mode>
0: Allow data calls
1: Barr data calls
9: Query status
<passwd>
Use any four digit value. (e.g. 1234)
Syntax (for Facility Lock):
Command syntax: AT+CLCK= <fac>,<mode>[,<passwd>]
Response syntax: +CLCK: <status>
Command
Possible Responses
AT+CLCK?
+CLCK:(“AO”,1),(“AI”,1),(“PB”,1),(“DT”,1)
Note: Get facility lock status
OK
Note: Outgoing call barring is enabled, Incoming call barring is
enabled, match string from phonebook is enabled, Data calls are
not allowed
AT+CLCK=”AO”,1,1234
Note: Bar Outgoing Calls
AT+CLCK=”AI”,1,1234
Note: Bar Incoming Calls
AT+CLCK=”AO”,9
OK
Note: Outgoing calls are barred
OK
Note: Incoming calls are barred
+CLCK: 1
Note: Query outgoing call
barring status
OK
Note: Outgoing calls are barred
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
189
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
Mobile Directory Number +WMDN
Description: This command is used to enter a new mobile directory number. Valid numbers are between
10 and 15 digits in length. For support of Wireless Number Portability, changes to the MDN
will ALWAYS update the IMSI_M portion (least significant 10 digits) of the IMSI. Changes to
the MDN will also automatically update the Access Overload Class values unless specifically
modified using the +WAOC command. The new IMSI_M and Access Overload Class values
will not be visible in the WIMI and WAOC commands until after the changes are committed
with the WCMT command.
The security PIN (WPIN) is automatically updated using the following logic whenever the
+WMDN command is used to change the mobile directory number (MDN).
If (Security PIN = Last 4 digits of MDNold) Then
Set Security PIN = Last 4 digits of MDNnew
Else
Don't Change Security PIN
EndIf
Example 1:
Current PIN = 1234
Current MDN = 5551234 (last 4 digits are the same as PIN digits)
If MDN is set to 5556789, then PIN changes to 6789.
Example 2:
Current PIN = 3456
Current MDN = 5551234 (last 4 digits and the PIN digits are different)
If MDN is set to 5556789, then PIN remains 3456.
Syntax:
Command syntax: AT+WMDN=<number>
Command
Possible Responses
AT+WMDN?
+WMDN: 8581111111
Note: Get current mobile directory number
OK
AT+WMDN=8585551212
OK
Note: Set mobile directory number to 8585551212
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
190
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
Serving System +CSS
Description: The numeric parameter is used to query the serving system.
Values:
<Class>
0: No service
1: 800 MHz
2: 1900 MHz
<Band>
A – B: Cellular 800
PA – PF: PCS 1900
Z: The mobile station is not registered
Note: For the <Band> parameter, the value will be two letters for PCS. The first will be
'P' and the second will be the block ('A' - 'F').
<SID>
0: No service
1 – 32767: The mobile station is registered with the system indicated.
99999: The mobile station is not registered.
<BS_P_REV> (Base Station Protocol Revision In Use – Band Class 0/Cellular)
1: IS-95
2: IS-95A
3: TSB74
4: N/A
5: IS-95B
6: IS-2000
7: IS-2000A
<BS_P_REV> (Base Station Protocol Revision In Use – Band Class 1/PCS)
1: J-STD-008C
2: N/A
3: N/A
4: N/A
5: IS-95B
6: IS-2000
7: IS-2000A
<CHANNEL>
0 – Max RF Channel Number
Syntax:
Command syntax: AT+CSS Returns: <Class>,<Band>,<SID>,<BS_P_REV>,<CHANNEL>
Command
Possible Responses
AT+CSS?
+CSS: 2, A, 4145, 6, 334
Note: Display the current setting
OK
Note: Command is valid
AT+CSS=?
+CSS:
Note: Display the range of
setting
OK
Note: Command is valid however range display is not
supported for this command due to carrier-specific
requirements.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
191
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
Packet Zone Identifier +PZID
Description: This is a read-only command that displays the Packet Zone Id for the mobile IP.
Values:
Syntax:
Numeric value in range 0 - 255
Command syntax: AT+PZID
Command
Possible Responses
AT+PZID
Note: Display the packet zone ID.
+PZID: 1
OK
Boot URL +WBURL
Description: This command is used to read and write the boot URL value. This value is required for IOTA
connections.
Note: Following a software load, the AT+WPRR command must be used to establish the
default value.
Values:
Syntax:
<string>: 128 character maximum length string value.
Default: http://hcmci.iota.spcsdns.net:8080/ciip
Command syntax: AT+WBURL=<string>
Command
Possible Responses
AT+WBURL?
http://hcmci.iota.spcsdns.net:8080/ciip
Note: Display the current boot URL value.
OK
AT+WBURL=http://hcmci.iota.spcsdns.net/ciip
Note: Set the boot URL value.
OK
Note: New value set.
AT+WBURL=””
+CERROR: BAD REQUEST
Note: Set invalid URL value.
Note: Error message displayed.
Trusted Domain +WTDMN
Description: This command is used to read and write the trusted domain value. This value is required for
IOTA connections and is used to verify the trusted server connection.
Note: Following a software load, the AT+WPRR command must be used to establish the
default value.
Values:
Syntax:
<string>: 32 character maximum length string value. Default: https:.iota.spcsdns.net
Command syntax: AT+WTDMN=<string>
Command
AT+WTDMN?
Note: Display the current trusted domain value.
AT+WTDMN=https:.iota.spcsdns.net
Note: Set the trusted domain value.
AT+ WTDMN =””
Possible Responses
https:.iota.spcsdns.com
OK
OK
Note: New value set.
+CERROR: BAD REQUEST
Note: Error message displayed.
Note: Set invalid URL value.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
192
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
Proxy Address +WDPXY
Description: This command is used to read and write the proxy server address. The proxy server address
is required for IOTA connections.
Note: Following a software load, the AT+WPRR command must be used to establish the
default value.
Values:
Syntax:
<string>: 32 character maximum length string value in URL format.
Default: 68.28.31.1
Command syntax: AT+WDPXY=<address>
Command
Possible Responses
AT+WDPXY?
68.28.31.2
Note: Display the current proxy server address value.
OK
AT+WDPXY=68.28.31.1
OK
Note: Set the proxy server address value.
AT+ WDPXY =””
Note: Set invalid address value.
Note: New value set.
+CERROR: BAD REQUEST
Note: Error message displayed.
WIOTA Connection Control +WIOTA
Description: This command is to start an IOTA session.
Values:
Syntax:
1: Connect – Start IOTA session to get profile.
Command syntax: AT+WIOTA=<value>
Command
Possible Responses
AT+WIOTA=1
OK
Note: Start IOTA session.
Note: Session started.
Sprint®. System Selection +WSSS
Description: This command is used to set the system selection and is persistent on reset. The values that
are available with the +WSSS command are dependent upon the currently loaded PRL.
Values:
Syntax:
<pref> Preferred only systems:
0: Home Only - Modem will operate on Sprint® PCS only.
1: Automatic - Roaming allowed on affiliated systems.
2: Analog only - Roaming rate applies.
Command syntax: +WSSS: <pref>
Command
Possible Responses
AT+WSSS=?
+WSSS: (0-3)
Note: Show supported parameters
OK
AT+WSSS?
+WSSS: 1
Note: Get current setting
AT+WSSS=0
OK
OK
Note: Set home only
Note: Home only mode set.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
193
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
IOTA Error +WOAE
Description: This response indicates that an IOTA failure has occurred. Refer to Sprint® document SEBU
3G NAI dual launch v131 sec 1.2 for additional details.
Syntax:
Response Syntax: +WOAE: “IOTA error 1012”
Command
Possible Responses
+WOAE: “IOTA error 1012”
Preparing Data Services +WOAP
Description: This response indicates that IOTA provisioning is in progress.
Syntax:
Response Syntax: +WOAP: “Preparing Data Services”
Command
Possible Responses
+WOAP: “Preparing Data Services”
Please Retry +WOAR
Description: This response indicates that the previous attempt to start a data session should be retried.
When a data session is started without a valid profile, IOTA provisioning is initiated. Upon
completion of profile provisioning, this response is displayed.
Syntax:
Response Syntax: +WOAR: “Please Retry”
Command
Possible Responses
+WOAR: “Please Retry”
Display PRI Checksum +WSUM
Description: This command is used to display the PRI checksum value. This checksum value is
calculated and programmed into the modem at the time of manufacture. The checksum
value is not updated or changed if a user modification is made to any of the PRI settings.
Syntax:
Command syntax: +WSUM?
Command
Possible Responses
AT+WSUM?
+WSUM: 0004DDCF
Note: Display checksum
value.
OK
Note: The displayed value is a eight digit hexadecimal number.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
194
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 23 - Sprint® Specific AT Commands
Reset MIN and MDN to factory defaults +WRMM
Description: This command is used to reset MIN and MDN to their factory default values. The service
programming code must be successfully entered using the +WSPC command prior to using
the +WRMM command. The modem must be manually reset or power cycled following the
use of the +WRMM command.
Syntax:
Command syntax: +WRMM
Command
Possible Responses
AT+WRMM
OK
Note: Reset MIN and MDN to factory defaults.
Note: Command successful.
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C
195
Download from Www.Somanuals.com. All Manuals Search And Download.
|