Simply Engineered Better
Technical Manual
Undercounter
Dishwasher
Model
401-HT
401-HTN
401-LT
Machine Serial No.
February, 2003
Manual P/N 0509604
REV. G
2674 N. Service Road
Jordan Station, Ontario, Canada L0R 1S0
905/562-4195
Fax: 905/562-4618
Moyer Diebel, Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
REVISIONS
Revision History
Revision
Date
Revised
Pages
Serial Number
Effectivity
Comments
02/28/97
09/09/98
09/09/98
02/28/00
07/21/00
08/22/01
12/12/01
11/04/02
11/04/02
11/04/02
2/5/03
All
7791
7791
7791
7791
7791
—
Issue of manual and replacement parts lists.
Changed booster tank part number.
Changed item 15 hose part number.
Revised electrical schematic.
27
29
40, 41, 42, 43
17, 23, 37
Revised part numbers.
21
27
17
23
37
37
Revised part numbers.
—
Revised fill hose part number.
—
Revised part number for front panel.
Revised part number for pump assembly.
Revised part number for control cabinet.
Revised part number 108391 to 113622.
—
—
—
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE
INTENTIONALLY
LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
CONTENTS
Page
INTRODUCTION....................................................................................................................................... 1
WARRANTY.............................................................................................................................................. 2
GENERAL .................................................................................................................................................. 3
INSTALLATION........................................................................................................................................ 5
Unpacking ............................................................................................................................................ 5
Electrical Connections.......................................................................................................................... 5
Plumbing Connections ......................................................................................................................... 6
Detergent .............................................................................................................................................. 6
Rinse-Aid ............................................................................................................................................. 6
Chemical Sanitizer ............................................................................................................................... 6
Completing Installation........................................................................................................................ 7
OPERATION .............................................................................................................................................. 8
Operation Summary ............................................................................................................................. 8
Operation Procedures ........................................................................................................................... 8
MAINTENANCE........................................................................................................................................ 10
Cleaning Schedule................................................................................................................................ 10
Deliming............................................................................................................................................... 11
Deliming Process.................................................................................................................................. 11
Maintenance Schedule.......................................................................................................................... 12
TROUBLESHOOTING .............................................................................................................................. 13
REPLACEMENT PARTS........................................................................................................................... 15
ELECTRICAL DIAGRAMS ...................................................................................................................... 39
TIMER CHARTS AND DIAGRAMS........................................................................................................ 44
LIST OF FIGURES
Figure 1—Track and Panel Assembly......................................................................................................... 16
Figure 2—Door and Switch Assembly........................................................................................................ 18
Figure 3—Tank/Drain Assembly ................................................................................................................ 20
Figure 4—Pump Assembly ......................................................................................................................... 22
Figure 5—Wash System Assembly............................................................................................................. 24
Figure 6—Booster Assembly and Water Inlet Piping (HT Only)............................................................... 26
Figure 7—Water Inlet Piping (HTN, LT Only) .......................................................................................... 28
Figure 8—Fill System ................................................................................................................................. 30
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Figure 9—Detergent Pump Assembly......................................................................................................... 32
Figure 10—Sanitizer/Rinse-Aid Pump Assembly....................................................................................... 34
Figure 11—Control Panel Assembly........................................................................................................... 36
Figure 12—Electrical Diagram, 401-HT..................................................................................................... 40
Figure 13—Electrical Diagram, 401-HTN.................................................................................................. 41
Figure 14—Electrical Diagram, 401-LT ..................................................................................................... 42
Figure 15—Electrical Diagram, 401-HT (50 Hz) ....................................................................................... 43
Figure 16—Timer Chart and Diagram, 401-HT, HTN ............................................................................... 44
Figure 17—Timer Chart and Diagram, 401-LT.......................................................................................... 45
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
INTRODUCTION
Welcome to Moyer Diebel.
Thank you for choosing Moyer Diebel and for allowing us to take care of your dishwashing
needs.
This manual covers several models. Model numbers are shown on the front cover.
Your machine has been completely assembled, inspected, and thoroughly tested at our factory to
eliminate problems at installation before it was shipped to your installation site. This manual
provides:
•
•
•
•
•
Warranty information
Installation and operation procedures
Maintenance instructions
Troubleshooting guide
Replacement parts lists.
Complete and return your warranty registration card as soon as possible.
Moyer Diebel constantly improves its products; therefore, specifications contained in this
manual may have changed.
For your protection, factory authorized parts should always be used.
Replacement parts may be ordered from your Moyer Diebel authorized parts distributor or
service agency. When ordering parts, supply the model number, serial number, voltage and phase
of your machine, the part number, part description, and quantity.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
LIMITED WARRANTY
Champion Industries/Moyer Diebel Limited, P.O. Box 4183, Winston-Salem, North Carolina 27115, and P. O. Box 301, 2674
North Service Road, Jordan Station, Ontario, Canada L0R 1S0 warrants machines, and parts, as set out below.
Warranty of Machines: Champion Industries/Moyer Diebel Limited warrants all new machines of its manufacture bearing
the name “Champion” or "Moyer Diebel" and installed within the United States and Canada to be free from defects in
material and workmanship for a period of one (1) year after the date of installation or fifteen (15) months after the date of
shipment by Champion/Moyer Diebel, whichever occurs first. [See below for special provisions relating to Model Series DF
and SW.] The warranty registration card must be returned to Champion/Moyer Diebel within ten (10) days after installation.
If warranty card is not returned to Champion/Moyer Diebel within such period, the warranty will expire after one year from
the date of shipment.
Champion/Moyer Diebel will not assume any responsibility for extra costs for installation in any area where there are
jurisdictional problems with local trades or unions.
If a defect in workmanship or material is found to exist within the warranty period, Champion/Moyer Diebel, at its election,
will either repair or replace the defective machine or accept return of the machine for full credit; provided, however, as to
Model Series DF and SW, Champion/Moyer Diebel's obligation with respect to labor associated with any repairs shall end
(a) 120 days after shipment, or (b) 90 days after installation, whichever occurs first. In the event that Champion/Moyer
Diebel elects to repair, the labor and work to be performed in connection with the warranty shall be done during regular
working hours by a Champion/Moyer Diebel authorized service technician. Defective parts become the property of
Champion/Moyer Diebel. Use of replacement parts not authorized by Champion/Moyer Diebel will relieve Champion/
Moyer Diebel of all further liability in connection with its warranty. In no event will Champion/Moyer Diebel's warranty
obligation exceed Champion/Moyer Diebel's charge for the machine. The following are not covered by Champion/Moyer
Diebel's warranty:
a. Lighting of gas pilots or burners.
b. Cleaning of gas lines.
c. Replacement of fuses or resetting of overload breakers.
d. Adjustment of thermostats.
e. Adjustment of clutches.
f. Opening or closing of utility supply valves or switching of electrical supply current.
g. Adjustments to chemical dispensing equipment.
h. Cleaning of valves, strainers, screens, nozzles, or spray pipes.
i. Performance of regular maintenance and cleaning as outlined in operator’s guide.
j. Damages resulting from water conditions, accidents, alterations, improper use, abuse,
tampering, improper installation, or failure to follow maintenance and operation procedures.
Examples of the defects not covered by warranty include, but are not limited to: (1) Damage to the exterior or interior finish
as a result of the above, (2) Use with utility service other than that designated on the rating plate, (3) Improper connection to
utility service, (4) Inadequate or excessive water pressure, (5) Corrosion from chemicals dispensed in excess of recom-
mended concentrations, (6) Failure of electrical components due to connection of chemical dispensing equipment installed
by others, (7) Leaks or damage resulting from such leaks caused by the installer, including those at machine table connec-
tions or by connection of chemical dispensing equipment installed by others, (8) Failure to comply with local building
codes, (9) Damage caused by labor dispute.
Warranty of Parts: Champion/Moyer Diebel warrants all new machine parts produced or authorized by Champion/Moyer
Diebel to be free from defects in material and workmanship for a period of 90 days from date of invoice. If any defect in
material and workmanship is found to exist within the warranty period Champion/Moyer Diebel will replace the defective
part without charge.
DISCLAIMER OF WARRANTIES AND LIMITATIONS OF LIABILITY. CHAMPION/MOYER DIEBEL'S
WARRANTY IS ONLY TO THE EXTENT REFLECTED ABOVE. CHAMPION/MOYER DIEBEL MAKES NO
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF
MERCHANTABILITY, OR FITNESS OF PURPOSE. CHAMPION/MOYER DIEBEL SHALL NOT BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THE REMEDIES SET OUT ABOVE ARE THE EXCLU-
SIVE REMEDIES FOR ANY DEFECTS FOUND TO EXIST IN CHAMPION/MOYER DIEBEL DISHWASHING
MACHINES AND CHAMPION/MOYER DIEBEL PARTS, AND ALL OTHER REMEDIES ARE EXCLUDED,
INCLUDING ANY LIABILITY FOR INCIDENTALS OR CONSEQUENTIAL DAMAGES.
Champion/Moyer Diebel does not authorize any other person, including persons who deal in Champion/Moyer Diebel
dishwashing machines, to change this warranty or create any other obligation in connection with Champion/Moyer Diebel
Dishwashing Machines.
rev. 8699
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
GENERAL
This manual covers the Moyer Diebel 401 undercounter dishwashing machine. This machine
is fully automatic and is equipped with a 1/2 H.P. pump motor. All models are available for
mounting directly to the floor or on optional stands (see accessories listed on page 4).
Standard equipment includes:
-Automatic tank fill
-Wash/rinse arm
-Common utility connections
-120 Volt control circuit
-Two dish racks (peg and flat)
-Exclusive vent design for
venting of condensation
-Convenient, easy to use controls
-Door latch activated start switch
-Pumped drain (to 3 ft/1m) (vertical)
-Stainless steel heavy-gauge construction
This series of dishwashers is available in the following models:
Model Numbers
401-HT, 401-HTN, 401-LT
•
•
The 401-HT model is a high temperature (82°C/180°F rinse) sanitizing model with booster.
The 401-HTN model is a high temperature (82°C/180°F rinse) sanitizing model without
booster.
•
The 401-LT model is a low temperature (60°C/140°F rinse) sanitizing model for use with
5.25% or 8.4% sodium hypochlorite solution (chlorine bleach) as a sanitizing agent. The
rinse aid pump is optional.
Options
•
•
•
•
•
•
•
•
Kit 512 - Detergent pump (P/N 0709624)
Kit 504 - Top and side panels (P/N 0708756)
Kit 505 - Top panel only (P/N 0708744)
Kit 506 - Left side panel only (P/N 0708745)
Kit 507 - Right side panel only (P/N 0708746)
Kit 508 - Rinse aid pump kit (P/N 0708754)
Kit 510 - Extended reach pumped drain kit (P/N 0708766)
Kit 511 - 30°C/70°F temperature rise booster (P/N 0708753)
(for 49°C/110°F supply water).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
Accessories
•
•
•
•
•
17RS - 17" rack stand (raises working height and adds rack storage)
17T - 17" cabinet (raises working height and adds storage)
CST - Combination sink/table (scraping and sorting station)
101285 - Dish Rack (Peg Rack)
101273 - Silverware Rack (Flat Bottom Rack)
Electrical Power Requirements
Booster
Rise
Machine
Power Requirement
Model
401-LT
401-HTN
401-HT
401-HT
401-HT
401-HT
Voltage
Full Load Amp (125% Service Factor)
115/60/1
115/60/1
208/60/1
240/60/1
208/60/1
240/60/1
N/A
N/A
40
9
15
15
42
47
57
64
9
33
37
45
51
40
70
70
NOTE:
208-230V/60Hz/1PH electrical supply service must be a 3-wire plus ground for connection
as shown.
00036
—3-Wire Plus Ground Diagram
115v
115v
208-230
L1
L2
N
G
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSTALLATION
Unpacking
WARNING:
!
Care should be taken when lifting the machine to prevent damage.
1. Immediately after unpacking your machine, inspect for any shipping damage. If damage is
found, save the packing material and contact the carrier immediately.
2. Remove the dishwasher from the skid. Adjust the feet if required, then move the machine to
its permanent location.
3. Level the machine (if required) by placing a level on the top of the machine and adjusting
the feet. Level the machine front-to-back and side-to-side.
CAUTION:
!
After locating your machine, the installation must meet local health codes. An example may
be to seal your machine to the floor using a good grade of silicone sealant.
Electrical Connections
WARNING:
!
Electrical and grounding connections must comply with the National Electrical Code
and/or Local Electrical Codes.
WARNING:
!
When working on the dishwasher, disconnect the electric service and tag it to indicate work
is being done on that circuit.
1. The electrician should compare the electrical specifications on the machine electrical rating
label (located on the lower left front panel) to the electrical power supply before connecting
the machine to the incoming service at a fused disconnect switch.
NOTE:
The 208-240V/60Hz/1PH electrical supply service for this machine must be a
3-wire plus ground service.
2. On the 208V-240V models, a terminal block is provided on the left front side of the
machine (located behind the front panel) for electrical service connections. A fused
disconnect switch or circuit breaker (supplied by user) is required to protect each power
supply circuit.
3. On 115V models, your machine is already equipped with a 4-foot power cord and plug
suitable for 115V-15A service.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Plumbing Connections
CAUTION:
!
Plumbing connections must comply with local sanitary and plumbing codes.
Water Connections
1. Connect the hot water supply (60°C/ 140°F Min) to the 1/2" I.D. fill hose provided. The fill
solenoid valve is equipped with a flow control that will accept water pressures from 172
kPa/25 psi to 665 kPa/95 psi.
2. Install a manual shut-off valve with 3/4" garden hose connection in the water supply line
close to the machine to accommodate installation and servicing the machine. The shut-off
valve should be the same size or larger than the supply line.
3. The fill solenoid valve is equipped with a built-in strainer to protect from particles in the
water supply.
Drain Connections
1. All Models are supplied with a flexible 5/8" I.D. drain hose, which must be connected to a
1-1/2" drain using a wye (Y) fitting close to the machine.
Detergent/Chemicals
Use a qualified detergent/chemical supplier for your detergent, rinse aid, and chemical
sanitizer needs.
1. Your machine may be fitted with an optional liquid detergent dispensing pump. Insert the
labeled detergent pickup tube into the detergent container. The pickup tube has a strainer on
the end to prevent crystallized chemical from clogging the supply lines.
2. The cycle timer located in the main control cabinet is equipped with adjustable cams for the
chemical dispensing pump(s). The cams control the length of time that the pumps operate.
A qualified person may adjust the cam settings if necessary. Refer to the timer chart
diagram(s) at the end of the manual for timer cam locations. Factory time settings are only
approximate. Have your chemical supplier check the concentration and make the necessary
adjustments.
NOTE:
A nonchlorinated detergent is recommended for your dishwasher.
Rinse Aid
1. An optional rinse aid pump may be added for all models. Insert the labeled Rinse Aid
pickup tube into the rinse aid container. Contact your chemical supplier for adjustment to
ensure proper dosage.
Chemical Sanitizer
1. Model 401-LT is supplied with chemical sanitizer dispensing pump. Using a 5.25% or 8.4%
sodium hypochlorite solution, insert the labeled Chemical Sanitizer pickup tube into the
chemical sanitizer container. Have your chemical supplier set chemical dosage according to
local code.
2. Contact your chemical supplier for adjustment of the chemical sanitizer to ensure proper
dosage.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Completing Installation
1. Remove any foreign material from inside the machine.
2. Center the scrap screen over the sump opening.
3. Prime the booster using the following procedure (if applicable).
CAUTION:
!
To prime the booster, the following procedure must be followed AFTER the electrical
and plumbing connections have been made and water has been turned on.
a. Open the dishwasher door.
b. Make sure the On-Fill/Off-Drain switch is in the Off-Drain position.
c. Push the Detergent/Rinse prime switch “down” to the Rinse position.
d. Hold the prime switch in the Rinse position until you observe water entering the wash
tank. The water inlet port is on the lower right side of the tank interior.
e. Release the switch. You have completed the booster priming process.
00034
ON
DET
FILL
RINSE
OFF
DRAIN
IN
CYCLE
WARNING:
!
Failure to prime the booster may cause damage to the booster
elements and other electrical components and will void the
warranty.
4. Check the machine for water leaks by depressing the ON/FILL switch on the front panel,
then close and latch the door. This allows the tank to automatically fill by using the rinse
cycle. Check for leaks.
5. Open the door and check the water level. The water level should be 1/2" over the scrap
screen.
6. Depress the OFF/DRAIN switch, close and latch the door to drain the machine. This allows
the machine to complete the 105-second wash and drain cycle. Check the drain plumbing
for leaks or kinks in drain hose.
7. Replace the front panel. Installation is now complete.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATION
Operation Summary (See Timer Chart in back of manual)
The following is a summary of your Undercounter Dishwashing Machine operating cycle:
1. The cycle begins when you close and latch the door.
2. The green cycle lamp lights and the wash pump starts.
3. The pump runs during the wash cycle for approximately 80 seconds.
4. The wash pump stops, and the drain valve is opened.
5. After a 2-3 second pause, the pump drain cycle begins and continues for approximately 30
seconds.
6. After a 2-3 second pause, the fill valve opens, and the pump starts for the rinse cycle.
7. Within approximately 25 seconds, the rinse cycle is complete. The pump stops, the green
cycle lamp turns off, and the cycle is complete.
8. Open the door and remove the rack of clean ware. The door must remain open for 5
seconds to allow the timer to reset before starting another cycle.
Daily Operation Procedures
The operation of your dishwasher will be more efficient when these procedures are followed:
1. Check that the spray arm and scrap screen are in place.
2. Close and latch the door. Push the ON/FILL switch to the ON position. The tank will begin
filling with water. This procedure is followed only when the tank is empty.
3. When the tank is full, check the wash tank temperature gauge. Minimum wash temperatures
are:
• 401-HT, 401-HTN - 66°C/150°F.
• 401-LT - 60°C/140°F.
CAUTION:
!
If the wash water temperature falls below the minimums listed
above, you must run an empty cycle to refill with fresh hot water.
4. Scrap and preflush all items to be washed, and load the items into the rack. DO NOT
OVERLOAD the rack. Wash only one layer of silverware in a rack.
5. Open the door and insert the rack into the machine.
6. Close and latch the door. This will start the wash cycle. The green cycle lamp located on the
front control panel will light. This lamp will remain on until the entire wash and rinse cycle
are completed.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
NOTE:
The machine may be stopped at any time by opening the door. When restarted, the cycle
does not start over. It will continue from the point at which it was interrupted.
7. Check the rinse temperature during the final rinse (120 seconds into cycle). The rinse
temperature must be 82°C/180°F minimum for models 401-HT and 401-HTN and
60°C/140°F for model 401-LT.
8. The pump will automatically stop and the green cycle light will turn off indicating the cycle
is completed.
9. Open the door and remove the rack.
10. Repeat steps 4-9 for additional cycles. Machine operation is automatic.
11. CLEAN the scrap screen after every meal period. During heavy usage, the scrap screen
should be cleaned more frequently.
CAUTION:
!
Poor machine performance and/or damage to the machine can occur if the scrap
screen becomes clogged with soil or waste particles.
12. To drain water out of the tank at the end of each day. Flip OFF/DRAIN switch to DRAIN
position. Close and latch door. Machine will drain completely in approximately 105
seconds.
CAUTION:
!
DO NOT LEAVE WATER IN THE TANK OVERNIGHT. Water left in the tank
overnight will allow harmful chemicals to deteriorate the tank.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MAINTENANCE
The efficiency and life of your machine is increased by regularly scheduled preventive
maintenance. A well maintained machine gives better results and service. An investment of a few
minutes of daily maintenance will be worthwhile.
The best maintenance you can provide is to keep your machine clean. Components that are not
regularly cleaned and flushed will clog and become inoperative.
Intervals shown in the following schedules represent an average length of time between
necessary maintenance. Maintenance intervals should be shortened whenever your machine is
faced with abnormal working conditions, hard water, or multiple shift operations.
Cleaning Schedule
•
Daily-Every 8 Hours
1. Depress the OFF/DRAIN switch to OFF and close and latch the door to drain the
tank.
2. Open the door and remove the lower spray arm by unscrewing the knurled fastener.
3. Remove the scrap screen carefully to keep soil or waste particles from falling into the
sump. Remove any material caught in pump intake.
4. Clean inside the tank with clean water. Backflush the scrap screen until it is clean. Do
not strike the screen against solid objects.
5. Clean the wash arm to remove any debris from spray openings. Do not strike the spray
arm against solid objects.
6. Reinstall the scrap screen and spray arm.
7. Leave the door open overnight to allow drying.
8. Report any unusual conditions to your supervisor.
Meal Periods
•
1. Clean the scrap screen after every meal period and more frequently during heavy
usage. Do not allow the scrap screen to become clogged with soil or waste particles.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Deliming
Your dishwasher should be delimed regularly as required. This will depend on the mineral
content of your water.
Inspect your machine interior for lime deposits. If deliming is required, a deliming agent should
be used for best results.
If you have the chemical sanitizing model (401-LT), carefully follow the following procedure
before deliming:
DANGER:
!
Deliming solution or other acids must not come in contact with household bleach (sodium
hypochlorite) or any chemicals containing chlorine, iodine, bromine, or fluorine. Mixing
will cause hazardous gases to form. Skin contact with deliming solutions can cause severe
irritation and possible chemical burns. Consult your chemical supplier for specific safety
precautions.
1. Remove the sanitizer tube from the container. Place the tube into a container of hot water.
2. Depress and hold the SANITIZER prime switch (located on the front panel) until all
sanitizer has been purged from the hoses.
3. Close the door and depress the door latch. Complete two operating cycles to purge the
machine of all sanitizer.
Deliming Procedure
Complete the following procedure to delime your machine:
1. Add the delime chemical to wash the tank (per chemical supplier specifications).
2. Close and latch the door.
3. The dishwasher will complete a regular cycle.
4. Check the deliming results and repeat if necessary per the chemical supplier’s
specifications.
5. Operate the dishwasher for at least four complete cycles to purge the machine of any
deliming chemicals.
6. For chemical sanitizing Model 401-LT, re-prime sanitizer chemical line and run an
additional cycle to flush any excess sanitizer from machine.
7. Drain the dishwasher. Deliming is complete.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance Schedule
•
As Required
1. Check the temperature gauge reading.
2. Check the chemical supplies and refill as necessary.
Weekly
•
1. Inspect all water lines for leaks and tighten them at joints if required.
2. Clean all detergent residue from the exterior of the machine.
3. Check the drain for leaks.
4. Remove and closely inspect the spray arm for blockage.
5. Check for damage to the scrap screen. Ineffective screening can cause wash system
failures, or poor washing results.
6. Clean the detergent, sanitizer, and rinse aid supply tubes (if equipped). Complete the
following procedure:
a. Remove the detergent, sanitizer, and rinse aid pick-up tube(s) from the
container(s). Place the tube(s) into a container of hot water.
b. Ensure ON/OFF switch is in the ON position depress and hold the DET prime
switch (located on the front panel) until clear water enters the tank through the
fill air gap (located on the right side of the tank).
c. If your machine is equipped with a sanitizer and/or rinse aid pump, follow the
same procedure by pressing the SANITIZER and/or the RINSE AID prime
switch until clear water enters the tank through the fill air gap.
d. When completed, remove the pickup tubes from the hot water and reinsert them
into the correct chemical containers. Repeat the priming procedures to ensure
that chemicals have filled the tubes for the next operating period.
e. Run a complete cycle to flush chemicals from the tank.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TROUBLESHOOTING
Before determining any specific cause of a breakdown or abnormal operation of your dishwasher,
check that:
1. Power supply is turned on. All switches are ON.
2. Wash arm is clean.
3. Scrap screen is properly positioned and clean.
4. Thermostat is at the correct setting.
5. Sanitizer, detergent, and rinse additive dispensers (if equipped) are adequately filled.
6. All plumbing valves are open and drain hose is not kinked.
If a problem still exists, use the following table for troubleshooting.
CONDITION
CAUSE
SOLUTION
Machine will not start
Door not closed and latched. . . . . . . .
Main switch off, or unit unplugged . .
Make sure door is fully latched
Check disconnect or plug into outlet
Low or no water
Main water supply is turned off . . . .
Water level setting low. . . . . . . . . . . .
Turn on house water supply
Adjust water level
Chemical not feeding
No chemical in container . . . . . . . . . .
Feed tubes to/from chemical . . . . . . .
pump clogged
Replace or fill container
Clear obstruction and flush
with hot water
Screen on feed tube clogged. . . . . . . .
Tubing kinked or split . . . . . . . . . . . .
Clean and replace
Straighten or replace tubing
Water temperature
is low when in use
Incoming water temperature. . . . . . . .
at machine too low
Raise house supply temperature to
60°C/140°F for all machines
Insufficient pumped spray
pressure
Clogged spray arm . . . . . . . . . . . . . . .
Scrap screen full. . . . . . . . . . . . . . . . .
Clean
Must be kept clean and in place
Low final rinse temperature
Low incoming water. . . . . . . . . . . . . .
temperature
Check the booster - be sure the
thermostat is set to maintain 66°C/180°F
temperature (401-LT is 60°C/140°F)
(Check all valves to be
sure they are clean and operating)
Poor washing results
Detergent dispenser not . . . . . . . . . . .
operating properly
Contact service agent
Insufficient detergents . . . . . . . . . . . .
Check dosage
Check and fill
Contact detergent supplier
Contact detergent supplier
See above booster temperatures, run cycle
Clean wash arm
Check scraping procedures
Use proper racks - do not overload
racks
Detergent setting too low . . . . . . . . .
Wash water temperature too low . . . .
Wash arm clogged . . . . . . . . . . . . . . .
Improperly scraped dishes . . . . . . . . .
Ware being improperly. . . . . . . . . . . .
placed in rack
Improperly cleaned . . . . . . . . . . . . . .
equipment
Unclog wash arm to maintain
proper pressure and flow conditions
No water in wash well
Opening door prior. . . . . . . . . . . . . . .
to cycle completion
Close and latch door. Wait for green light
to go out before opening door.
Water supply is turned off . . . . . . . . .
Turn on supply
No water in wash tank
after activating the
ON/FILL switch
Door not latched. . . . . . . . . . . . . . . . .
Latch door
Wait for wash tank to fill
13
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE
INTENTIONALLY
LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
REPLACEMENT
PARTS
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00050
12
11
10
12
7
6
4
9
5
3
12
2
8
1
Figure 1 — Track and Panel Assembly
16
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
TRACK AND PANEL ASSEMBLY
Description
Fig. 1
Part
Qty
Item No. No.
1
2
3
4
5
6
7
8
9
0508751
Screw, 10-32 x 1-1/2" Lg. Truss Head.......................................
Front Panel .................................................................................
Screw, 10-32 x 3/8" Lg. Round Head.........................................
Screw, 10-32 x 5/8" Lg. Round Head.........................................
Track, RH ...................................................................................
Track, LH ...................................................................................
Cover, Vent.................................................................................
Panel, LH Side ...........................................................................
Panel, Rear ................................................................................
Panel, RH Side ..........................................................................
Panel, Top ..................................................................................
Screw, 10-32 x 3/8" Lg. Truss Head ..........................................
2
1
2
4
1
1
2
1
1
0309572
0501413
0501415
0308632
0308631
0708647
0308736
0308734
0308737
0308735
0501412
10
11
12
1
1
10
17
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00020
11
1
5
4
8
7
6
10
9
12
3
1
14
13
2
1
15
18
16
17
15
Figure 2 — Door and Switch Assembly
18
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
DOOR AND SWITCH ASSEMBLY
Description
Fig. 2
Part
Qty
Item No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
-
0501412
Screw, 10-32 x 3/8" Truss Head.................................................
Plate, Door Latch........................................................................
Handle, Door Latch....................................................................
Retaining Ring, Plunger.............................................................
Assembly, Door Catch (Includes items 4, 6)..............................
Plunger, Door Catch...................................................................
Gasket, Steam.............................................................................
Screw, Round Head (6-32 x 3/8") ..............................................
Plate, Door Switch......................................................................
Switch, Door Magnetic Reed .....................................................
Gasket, Upper Door....................................................................
Gasket, Side Door ......................................................................
Nut, Plain 1/4-20 ........................................................................
Spring, Door Hinge ....................................................................
Bolt, 1/4-20 x 1-1/4" Hex Head .................................................
Arm, Door Hinge........................................................................
Washer, Lock 1/4" Split .............................................................
Door............................................................................................
Wiring, Harness, Door Switch ...................................................
6
1
1
1
1
1
2
2
1
1
1
2
2
2
4
2
2
1
1
0308596
0308597
0508721
0709462
0509436
0508545
104883
0709431
111090
0508544
0508543
0501539
0503715
0501421
0708564
0501501
0708527
0508555
-
0708526
Door Assy. (includes items 1-6, 18)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00037
1
2
3
4
5
THERMOMETER
(CALLED OUT IN
CONTROL BOX)
6
7
TO PUMP
10
11
11
12
8
TO DRAIN
9
Figure 3 — Tank/Drain Assembly
20
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
TANK/DRAIN ASSEMBLY
Description
Fig. 3
Part
Qty
Item No. No.
1
2
3
4
5
6
7
8
9
0508628
201029
Scrap Screen...............................................................................
Locknut, 1/2 NPT Nickel-Plated................................................
O-Ring, Thermometer................................................................
Adapter, Thermometer ...............................................................
Nut, Plain 1/4-20 ........................................................................
Washer, Lock, 1/4" Split.............................................................
Support, Drain Valve..................................................................
Valve, Drain................................................................................
Screw, 1/4-20 x 1/2" Lg. Round Head .......................................
Hose, 5/8" ID x 7/8" OD PVC Braided (3 ft.) ..............................
Clamp, hose................................................................................
Hose 5/8" ID x 1" OD Braided PVC..........................................
1
1
2
1
2
2
1
1
2
2
2
1
0501836
0508872
0501539
0501501
0308611
0306618
0501418
0507265
0510082
0509302
10
11
12
21
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00005
1
3
2
4
7
5
6
8
9
10
13
14
11
12
TANK
BOTTOM
Figure 4 — Pump Assembly
22
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
PUMP ASSEMBLY
Description
Fig. 4
Part
Qty
Item No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
*-
*-
-
0508542
Spindle, Lower Wash Arm.........................................................
Screw, 8-32 x 1-1/8" Round Head..............................................
Screw, 8-32 x 5/8" Round Head.................................................
Housing, Top (No Hole).............................................................
Diffuser.......................................................................................
Impeller ......................................................................................
Adapter Plate, Suction................................................................
Plate, Drain lnlet.........................................................................
O-ring .........................................................................................
Propeller/Rotating Seal Assembly .............................................
Mounting Plate/Seal Assembly (Includes Item 10)....................
Gasket, Pump .............................................................................
Screw, 10-32 x 5/8" Hex Washer Head......................................
Washer, Sealing Teflon...............................................................
Pump/Motor Assembly (50/60 Hz, 220V) (Export machines) ..
Pump/Motor Assembly (50/60 Hz (115V).................................
Nut, Grip 10-32, SST (Not Shown) (For mounting Item 1).......
1
4
4
1
1
1
1
1
1
1
1
1
8
8
1
1
1
0501431
0501425
0502742
0502741
0502704
0502746
0502745
0502703
0502744
0502743
0501881
0508665
0508570
0508973
0710072
107966
* Motor not available as a separate repair part
23
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00038
1
2
3
4
PUMP
TANK BOTTOM
Figure 5 — Wash System Assembly
24
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
WASH SYSTEM ASSEMBLY
Description
Fig. 5
Part
Qty
Item No. No.
1
2
3
4
0501563
Screw, #8 x 3/8" (Sheet Metal) Truss Head ...............................
Nut, Spray Arm Lock.................................................................
Wash Arm, Lower ......................................................................
Bushing, Lower Wash Arm........................................................
4
1
1
1
0501684
0705049
0508540
25
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
Figure 6 — Booster Assembly and Water Inlet Piping
(HT Only)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
BOOSTER ASSEMBLY AND WATER INLET PIPING
(HT ONLY)
Fig. 6
Part
Description
Qty.
Item No. No.
1
2
3
4
5
6
7
8
9
0509214
Hose, 1/2" I.D.............................................................................
Clamp, hose................................................................................
Elbow, 3/8 MPT X1/2 Hose x 90°..............................................
Bushing, reducing 3/4 NPT x 3/8 NPT Brass ............................
Nut, grip 6-32 w/nylon insert.....................................................
Thermostat, high limit................................................................
Tank, booster (tank only) ...........................................................
Bolt (1/4-20 x 1/2" Hex Hd).......................................................
Washer, lock 1/4 split .................................................................
Hose 1/2” x 7’ ............................................................................
Coupler, 3/8 MPT x 1/2..............................................................
Valve, solenoid (3/8 NPT)..........................................................
Repair kit, 3/8" valve..................................................................
Coil, 115V 3/8" valve.................................................................
Flow washer, 3/8" valve.............................................................
Elbow, reducing 1/2 MPT x 3/8 MPT 90° .................................
Plug, pipe 1/8"............................................................................
O ring, gasket .............................................................................
Heater element, 9KW (70° rise) 208/230V 1PH
3 ft.
2
1
1
2
1
1
2
2
1
1
1
1
1
1
1
1
0503679
0502653
0508840
108954
110562
0509607
0501419
0501501
0509526
0502618
0504952
0502811
0505235
0504958
0509606
0508817
109985
10
11
12
13
14
15
16
17
18
*19
1
111233
(existing 70° rise) .......................................................................
Conversion Kit 410° to 70° Rise................................................
Heater element, 6KW (40° rise) 208/230V 1PH........................
Nut, plain 1/4-20 ........................................................................
Cover, heater element.................................................................
Foot, adjustable ..........................................................................
Bushing, reducing face 3/4" to 1/2" Brass (not shown) .............
1
AR
1
6
1
*19
20
21
22
23
24
0708753
111235
0501539
107908
0503718
100171
4
1
* When converting machine contact factory with serial number. Kit is supplied with new data
plate for machine. Factory will supply jumper settings for element at time of installation.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
Figure 7 — Water Inlet Piping
(HTN, LT Only)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
WATER INLET PIPING
(HTN, LT ONLY)
Description
Fig. 7
Part
Qty
Item No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0503718
Foot, adjustable ..........................................................................
Clamp, hose................................................................................
Hose, 1/2" I.D. clear braided (LT Only).....................................
Hose, 1/2" I.D. white (HTN Only).............................................
Elbow, 3/8 MPT x 1/2" Hose x 90° Brass..................................
Valve, solenoid (3/8NPT)...........................................................
Repair kit, 3/8" valve..................................................................
Coil, 115V 3/8" valve.................................................................
Flow washer, 3/8" valve.............................................................
Washer, lock 1/4" split................................................................
Bolt, 1/4-20 x1/2" Hex Hd .........................................................
Clamp, valve support..................................................................
Coupling, 3/8 MPT x 3/4" hose barb .........................................
Washer, hose...............................................................................
Hose, coupled.............................................................................
4
3
3 ft.
3 ft.
1
1
1
1
1
2
2
1
1
2
1
0503679
0502665
0509214
0502653
0504952
0502811
0505235
0504958
0501501
0501419
0300203
0502618
0505320
0509526
29
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00039
Figure 8 — Fill System
30
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
FILL SYSTEM
Description
Fig. 8
Part
Qty
Item No. No.
1
2
3
4
5
6
7
8
0502665
0501518
106090
Hose, 1/2" I.D. Clear Braided (HTN, LT)..................................
Tie Wrap, Hose...........................................................................
Bracket, Tie Wrap.......................................................................
Nut, Grip, 10-32 w/Nylon Insert ................................................
Gasket, Inlet Chute.....................................................................
Inlet Chute..................................................................................
Tie Wrap, Chemical Hose ..........................................................
Hose, Fill 1/2" I.D. (White)........................................................
A/R
2
2
8
1
1
3
3 ft.
107966
0509048
0508867
0501519
0509214
31
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00022
1
3
2
4
6
7
8
5
12
13
9
14
15
10
11
TO FILL
ASSY
16
16
22
17
18
22
19
20
21
TO DETERGENT
SUPPLY
Figure 9 — Detergent Pump Assembly (optional)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
DETERGENT PUMP ASSEMBLY (OPTIONAL)
Description
Fig. 9
Part
Qty
Item No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
0503757
Motor, Pump...............................................................................
Bracket, Detergent Pump (except LT)........................................
Bracket, Detergent/Sanitizer Pumps (LT) ..................................
Screw, M4 x 35mm Hex Head ...................................................
Screw, 10-32 x 3/8" Lg. Truss Head ..........................................
Housing, Pump...........................................................................
Washer, Lock #8 Split ................................................................
Screw,8-32 x 1/2" Lg. Pan Head ................................................
Screw, 8-32 x 5/8" Round Head.................................................
Screw, Set M6 x 8mm ................................................................
Rotor Assembly..........................................................................
Hose, Pump ................................................................................
Cover, Pump Housing ................................................................
Washer, Flat M4 .........................................................................
Nut, Wing M4.............................................................................
Tie Wrap, Hose...........................................................................
Hose, Detergent, 1/4" I.D. PVC (Clear).....................................
Elbow, 1/4" O.D. x 90° Barbed..................................................
Label, Detergent.........................................................................
Tube, Pick-Up ............................................................................
Strainer, Pick-Up Tube...............................................................
Tie Wrap, Hose...........................................................................
1
1
1
4
2
1
2
2
2
1
1
1
1
4
4
2
A/R
2
0308637
0308610
N/A
0501412
N/A
0501497
0504822
0501425
N/A
N/A
108194
N/A
N/A
N/A
0501519
0502667
0502644
0503695
0306363
0501869
0501519
1
1
1
2
-
-
109829
0708559
Pump Head Assy. (includes items 4, 6, 10-15)
Pump/Motor Assy. (includes items 1, 2, 4, 6-16, 18)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
00002
1
3
2
5
6
7
8
4
15
9
10
TO FILL
SYSTEM
DETERGENT
PUMP (SEE FIG. 9)
10
11
12
13
14
TO CHEMICAL SUPPLY
Figure 10 — Sanitizer/(Optional) Rinse-Aid Pump Assembly
34
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
SANITIZER/(OPTIONAL) RINSE-AID PUMP ASSEMBLY
LT
Fig. 10
Part
Description
Qty
Item No. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0503756
Motor, Pump...............................................................................
Bracket, Detergent/Rinse Pump (Optional)................................
Bracket, Sanitizer Pump.............................................................
Screw, 10-32 x 3/8" Lg. Truss Head ..........................................
Washer, Lock #8 Split ................................................................
Screw, 8-32 x 1/2" Lg. Pan Head ...............................................
Rotor Assy..................................................................................
Element Tube Assy (45cc/min)..................................................
Screw, 6-32 x 7/8" Lg. Pan Head ...............................................
Hose, 1/8" I.D. PVC (Clear).......................................................
Label, Sanitizer...........................................................................
Label, Rinse-Aid (Optional).......................................................
Tube, Pick-Up ............................................................................
Strainer, Pick-up Tube................................................................
Tie Wrap, Hose...........................................................................
1
1
1
2
4
4
1
1
2
A/R
1
1
1
1
0308610
0308697
0501412
0501497
0504822
0707142
0706635
0506589
0502666
0503694
0505483
0306363
0501869
0501519
2
-
-
0708561
0708754
Detergent Pump Assy. (HT & LT) (Optional)............................
(lncludes Detergent Pump and Items 2, 5-9)
1
Rinse-Aid Pump Assy. (Optional)
(Includes Items 1,3, 5-10, 12-15)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
S
L
U P
Figure 11 — Control Panel Assembly
36
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
CONTROL PANEL ASSEMBLY
Description
Fig. 11
Part
Qty.
Item No. No.
*1
*1
2
3
4
5
6
7
-
0708538
Timer assy (HT, HTN) (Includes items 2-5) ..............................
Timer assy (LT only) (Includes items 2-5).................................
Motor, timer................................................................................
Switch, timer ..............................................................................
Bracket, timer support................................................................
Bearing, timer.............................................................................
Contactor, 2 pole 50A, 240V (401 HT only) (Booster) .............
Relay, motor start (220V, 50Hz) ................................................
Relay, motor start (220V, 60Hz) ................................................
1
1
1
A/R
1
1
0708590
0504956
0501379
0308644
0503701
111703
0508974
0509642
0501358
0509428
0501403
0501493
0501472
0501533
0503749
0310330
109069
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
4
1
1
1
1
-
8
9
Relay, motor start (115V
, 50/60Hz)
............................................
Relay, door safety switch (15A, 120VAC coil)..........................
Screw (10-32 x 3/4 Rd Hd) ........................................................
Washer, lock (#10 ext. tooth) .....................................................
Washer, flat (#10 Brass) .............................................................
Nut, plain (10-32 Brass).............................................................
Board, terminal...........................................................................
Bracket, thermostat (401 HT only) ............................................
Thermostat, booster (401 HT only)............................................
Thermometer, 4 ft. Gas Filled (Replaces 108391) .....................
Lamp, green................................................................................
Switch, rocker (DPDT) ..............................................................
Switch, rocker (Spring return)....................................................
Label, switch, overlay ................................................................
French label, switch overlay.......................................................
Screw (10-32 x 3/8" Truss Hd)...................................................
Panel (sheet metal only) ............................................................
Block, terminal (3pole) (220V/50Hz)........................................
Transformer (Not Shown) (220V/50Hz)....................................
Block, fuse 600V, 30A (Not Shown) (220V/50Hz)....................
Fuse, 2.5 Amp, 250VAC (Not Shown) (220V/50Hz).................
10
11
12
13
14
15
16
17
18
19
20
20
21
22
23
-
113622
0508551
0501361
0501369
0509568
0509626
0501412
0309579
0504951
109064
106402
107289
0308967
0509645
107369
-
-
-
-
2
1
1
1
Box, transformer (220V/50Hz)
...............................................
Harness, Control Panel
( 2 2 0 V / 5 0 H z ) ................................
-
Contactor 25 FLA 2p 120V (Not Shown)(220V/50Hz)..............
37
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE
INTENTIONALLY
LEFT BLANK
38
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
ELECTRICAL
SCHEMATICS
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
00041
TO CUSTOMER DISCONNECT SWITCH
CUSTOMER TO SUPPLY RATED
115V NEUTRAL
230V
VOLTAGE/PHASE/Hz, AS SPECIFIED
PER ORDER, TO DISCONNECT SWITCH.
ALL POWER SUPPLIED TO EACH CONNECTION
POINT MUST COMPLY WITH ALL LOCAL
ELECTRICAL CODES.
GND
2
3
1
3
CTC
2
33
CT
2
1
1
NC NC
NO
NO
29
31
31
28
BOOSTER TANK
WTS
BHTR
MSW
30
4
4
HLTS
NO
5
5
35
NC
NO
33
33
32
3
3
TM
NC
35
8
6
NO
NC
1CR
NO
CAM 1
CLT
4
7
NC
WASH
START CW
NO
CAM 8
NC
/RINSE
BLU
13
14
15
1
2
3
4
5
NO
CAM 3
NC
SRC
L
S
9
NO
CAM 2
NC
9
12
19
START CCW
8
RED
BLK
DRAIN
16
17
PSDR
4
M
MAIN
TP
25
NO
CAM 5
3
3
34
WHT
GRN
F V
26
NC
(IF USED)
20
DP
GND
GND
NO
3
20
CAM 4
D V
DM
8
NC
16
17
16
8
NO
3
3
21
CAM 7
NC
17
8
(IF USED)
22
NO
3
RM
CAM 6
NC
DSS
5
5
50
1CR
BHTR
BLK
BLU
BOOSTER HEATER
BLACK
BLUE
CT
CONTACTOR
CONTACTOR COIL
DETERGENT MOTOR
DRAIN PUMP (IF USED)
DOOR SWITCH
DRAIN VALVE
PSDR PRIME SWITCH DETERGENT, RINSE
CTC
DM
DP
ICR
DDS
RM
RELAY
DOOR SAFETY SWITCH
RINSE MOTOR (IF USED)
CAM 1 HOMING
CAM 2 PUMP MOTOR
CAM 3 PUMP MOTOR REVERSING DV
DS
SRC
SS
CURRENT OPERATED START RELAY COIL
SERVICE SWITCH
CAM 4 DRAIN
CAM 5 FILL
CAM 6 RINSE
CAM 7 DETERGENT
CAM 8 CYCLE
EC/D
FV
GND
GRN
EXTENDED CYCLE/DELIME
FILL VALVE
GROUND
TM
TP
WHT
TIMER MOTOR
THERMAL PROTECTOR
WHITE
GREEN
WHTR WATER HEATER
WTS WATER THERMOSTAT
HTLS HIGH LIMIT THERMOSTAT
MSW MAIN SWITCH ON/FILL OFF/DRAIN
CLT
CYCLE ON LIGHT
Figure 12 — Electrical Diagram, 401-HT
40
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
00044
BLK
BLU
BLACK
BLUE
CLT
DM
DP
RL
DV
CYCLE ON LIGHT
DETERGENT MOTOR
PSS
PRIME SWITCH SANITIZER
RELAY
REED SWITCH
ICR
DSS
RM
SRC
SM
TM
TP
WHT
CAM 1 HOMING
DRAIN PUMP
(IF USED)
CAM 2 PUMP MOTOR
CAM 3 PUMP MOTOR REVERSING
CAM 4 DRAIN
CAM 5 FILL
CAM 6 RINSE
CAM 7 SANITIZER
CAM 8 DETERGENT
CAM 9 CYCLE
RELAY
DRAIN VALVE
FILL VALVE
GROUND
RINSE MOTOR
(IF USED)
CURRENT OPERATED START RELAY COIL
SANITIZER MOTOR
TIMER MOTOR
THERMAL PROTECTOR
WHITE
FV
GND
GRN
HTLS
MSW
GREEN
HIGH LIMIT THERMOSTAT
MAIN SWITCH ON/FILL OFF/DRAIN
WHTR WATER HEATER
WTS WATER THERMOSTAT
PSDR PRIME SWITCH DETERGENT, RINSE
Figure 13 — Electrical Diagram, 401-HTN
41
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
00045
TO CUSTOMER RECEPTACLE
CUSTOMER TO SUPPLY RATED
VOLTAGE/PHASE/Hz, AS SPECIFIED
PER ORDER, TO DISCONNECT SWITCH.
ALL POWER SUPPLIED TO EACH CONNECTION
POINT MUST COMPLY WITH ALL LOCAL
ELECTRICAL CODES.
115V 60Hz
BLK WHT
GND
1
2
1
1
2
2
8
MSW
CLT
NO
6
NC
NO
NO
NC
NO
NC
8
8
8
4
TM
CAM 1
7
NO
5
WASH
START CW
START CCW
MAIN
NC
CAM 9
1CR
13
BLU
RED
BLK
/RINSE
1
2
3
4
5
NO
NC
SRC
L
S
9
9
12
CAM 3
NO
CAM 2
NC
14
DRAIN
8
NC
M
15
NO
19
20
2
2
WHT
GRN
CAM 5
TP
F V
8
NC
(IF USED)
DP
NO
2
2
20
D V
CAM 4
GND
GND
NC
8
16
NO
NC
21
22
23
2
2
2
DM
CAM 8
16
17
8
PSDR
4
(IF USED)
RM
NO
17
18
CAM 6
34
NC
8
PSS
NO
CAM 7
SM
NC
8
DSS
1
2
50
1CR
BLK
BLU
BLACK
BLUE
CLT
DM
DP
CYCLE ON LIGHT
DETERGENT MOTOR
PSS
ICR
DSS
RM
PRIME SWITCH SANITIZER
RELAY
REED SWITCH
CAM 1 HOMING
CAM 2 PUMP MOTOR
DRAIN PUMP
RELAY
(IF USED)
RL
RINSE MOTOR
(IF USED)
CAM 3 PUMP MOTOR REVERSING
CAM 4 DRAIN
CAM 5 FILL
DV
FV
GND
GRN
HTLS
MSW
DRAIN VALVE
FILL VALVE
GROUND
SRC
SM
TM
TP
WHT
CURRENT OPERATED START RELAY COIL
SANITIZER MOTOR
TIMER MOTOR
THERMAL PROTECTOR
WHITE
CAM 6 RINSE
GREEN
CAM 7 SANITIZER
CAM 8 DETERGENT
CAM 9 CYCLE
HIGH LIMIT THERMOSTAT
MAIN SWITCH ON/FILL OFF/DRAIN
WHTR WATER HEATER
WTS WATER THERMOSTAT
PSDR PRIME SWITCH DETERGENT, RINSE
Figure 14 — Electrical Diagram, 401-LT
42
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
00048
5
TO CUSTOMER DISCONNECT SWITCH
230V
1
2
5
115 VAC
3
FUSE
XFMR
GND
3
1
2
2
33
CT
2
1
NC NC
NO
NO
1
31
29
28
1
BOOSTER TANK
BHTR
30
MSW
NO
WTS
31
HLTS
4
5
35
NC
NO
33
2
33
3
TM
NC
8
6
NO
NC
NO
3
8
8
CLT
Cam 1
4
7
NC
1CR
Wash/
Rinse
Start CW
Start CCW
Main
NO
Cam 8
NC
BLU
RED
BLK
13
35
NO
1
2
3
4
5
L
S
SRC
40
9
12
Cam 3
NO
Cam 2
NC
PSDR
8
14
DRAIN
16
17
NC
4
M
15
25
25
26
NO
41
19
34
WHT
GRN
3
V
TP
Cam 5
F
25
NC
(If used)
DP
3
20
GND
NO
9
9
NO
20
1
2
3
GND
V
D
NC
NC
Cam 4
8
NC
41
40
41
16
16
(If used)
DM
NO
NO
115 VAC
3
3
21
3
40
Cam 7
NC
COIL
17
17
8
(If used)
RM
NO
3
22
Cam 6
NC
3
3
DSS
5
5
50
1CR
BHTR
BLK
BOOSTER HEATER
BLACK
CT
CONTACTOR
1CR
DDS DOOR SAFETY SWITCH
RM RINSE MOTOR (IF USED)
SRC Current Operated Start Relay
RELAY
CTC
DM
DP
CONTACTOR COIL
DETERGENT MOTOR
BLU
BLUE
DRAIN PUMP (IF USED)
DOOR SWITCH
CAM 1
CAM 2
HOMING
PUMP MOTOR
DS
DV
SS
TM
TP
SERVICE SWITCH
TIMER MOTOR
DRAIN VALVE
CAM 3
CAM 4
CAM 5
CAM 6
PUMP MOTOR REVERSING
DRAIN
FILL
FV
FILL VALVE
THERMAL PROTECTOR
GND
GRN
GROUND
GREEN
WHT WHITE
RINSE
WHTR WATER HEATER
HTLS
MSW
PSDR
HIGH LIMIT THERMOSTAT
MAIN SWITCH On/Fill- Off/Drain
Prime Switch, Detergent/Rinse
WTS
WATER THERMOSTAT
CAM 7
CAM 8
CLT
DETERGENT
CYCLE
CYCLE ON LIGHT
0509643B
CUSTOMER TO SUPPLY RATED VOLTAGE/
PHASE/HZ, AS SPECIFIED PER ORDER, TO
DISCONNECT SWITCH. ALL POWER SUPPLIED
TO EACH CONNECTION POINT MUST
COMPLY WITH ALL LOCAL ELECTRICAL CODES.
Figure 15 — Electrical Diagram, 401-HT (50 Hz)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SCHEMATICS
00042
TIMING CHART 401-HT
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
CAM
TIME IN SECS
HOMING
CAM
1
2
WASH PUMP
FORWARD=WASH
WASH PUMP
2
REVERSE=DRAIN
WASH PUMP
REVERSING CAM
3
4
5
6
7
8
DRAIN VALVE
DRAIN PUMP
FILL VALVE
RINSE
OPTIONAL
PUMP
DETERGENT
PUMP
AUTO-FILL
DRAIN
N
C
N
O
COM.
TIMER
SWITCH
DETAIL
8 7 6 5 4 3 2 1
TIMER MOTOR
LOCKING SCREW
TIMER ASSEMBLY 401-HT
Figure 16 —- Electrical Diagram, 401-HT, HTN
44
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMING CHARTS
00043
TIMING CHART 401-LT
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
CAM
TIME IN SECS
HOMING
CAM
1
2
WASH PUMP
FORWARD=WASH
WASH PUMP
2
REVERSE=DRAIN
WASH PUMP
REVERSING CAM
3
4
5
6
7
8
9
DRAIN VALVE
DRAIN PUMP
FILL VALVE
RINSE
PUMP
SANITIZER
PUMP
DETERGENT
PUMP
AUTO-FILL
DRAIN
N
C
N
O
COM.
TIMER
SWITCH
DETAIL
8 7 6 5 4 3 2 1
9
TIMER MOTOR
LOCKING SCREW
TIMER ASSEMBLY 401-LT
Figure 17 —Timer Chart and Diagram, 401-LT
45
Download from Www.Somanuals.com. All Manuals Search And Download.
|