Mountfield Lawn Mower 550 SP User Manual

Mountfield

550 SP TRI-CUT

Owner’s Manual

Model: . . . . . . . . . . . . . . . .

Type: . . . . . . . . . . .

(Year) . . . . . . .

S/N° . . . . . . . . . . . . . . . .

O P S T

Call our Helpline if you have any problems:

Helpline Number

0870 240 2114

Open from 9:00am to 4:00pm daily

Manufactured by:

GGP ITALY SPA - Via del Lavoro, 6 - 31033 Castelfranco Veneto (TV) - ITALY

71503852/0

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

C) OPERATION

SAFETY REGULATIONS

A) TRAINING

1) Do not operate the engine in a confined

space where dangerous carbon monoxide

fumes can collect.

2) Mow only in daylight or good artificial light.

3) If possible, avoid operating the equipment in

wet grass.

4) Always be sure of your footing on slopes.

5) Walk, never run and do not allow yourself to

be pulled along by the lawnmower.

6) Mow across the face of slopes, never up and

down.

7) Exercise extreme caution when changing

direction on slopes.

8) Do not mow on slopes of more than 20°.

9) Exercise extreme caution when pulling the

lawnmower towards you.

10) Stop the blade if the lawnmower has to be

tilted for transportation when crossing surfaces

other than grass, and when transporting the

lawnmower to and from the area to be mowed.

11) Never operate the lawnmower with defec-

tive guards, or without safety devices, such as

the stone-guard and/or grass-catcher, in place.

12) Do not change the engine governor settings

or overspeed the engine.

1) Read the instructions carefully. Get familiar

with the controls and proper use of the equip-

ment. Learn how to stop the engine quickly.

2) Only use the lawnmower for the purpose for

which it was designed, i.e. for cutting and col-

lecting grass. Any other use can be hazardous,

causing damage to the machine.

3) Never allow children or people unfamiliar with

these instructions to use the lawnmower. Local

regulations may restrict the age of the operator.

4) Never use the lawnmower:

– When people, especially children, or pets are

nearby.

– If the operator has taken medicine or sub-

stances that can affect his ability to react and

concentrate.

5) Remember that the operator or user is

responsible for accidents or hazards occurring

to other people or their property.

13) On power-driven models, disengage the

drive clutch before starting the engine.

14) Start the engine carefully, following the

instructions and keeping feet well away from

the blade.

B) PREPARATION

1) While mowing, always wear sturdy footwear

and long trousers. Do not operate the equip-

ment when barefoot or wearing open sandals.

2) Thoroughly inspect the area where the equip-

ment is to be used and remove all objects which

may be thrown by the machine or damage the

cutter assembly and the engine (stones, sticks,

metal wire, bones, etc.)

15) Do not tilt the lawnmower when starting the

engine. Start the engine on a flat surface that is

free of obstacles and tall grass.

16) Do not put hands or feet near or under rotat-

ing parts. Keep clear of the discharge opening

at all times.

17) Never pick up or carry a lawnmower while

the engine is running.

3) WARNING: DANGER! Engine fuel is highly

flammable:

18) Stop the engine and disconnect the spark

plug wire:

– Store fuel in containers specifically designed

for this purpose.

– Before carrying out any work underneath the

cutting deck or before unclogging the chute;

– Before checking, cleaning or working on

lawnmower;

– Refuel using a funnel and outdoors only. Do

not smoke while refuelling or whenever han-

dling the fuel.

– Add fuel before starting the engine. Never

remove the cap of the fuel tank or add fuel while

the engine is running or when the engine is hot.

– If fuel is spilled, do not attempt to start the

engine but move the machine away from the

area of spillage and avoid creating any source

of ignition until the fuel has evaporated and the

vapour dispersed.

– After striking a foreign object. Inspect the

lawnmower for damage and make repairs

before restarting and operating the lawnmower;

– If the lawnmower starts to vibrate abnormal-

ly (find and remove the cause of the vibration

immediately).

19) Stop the engine:

– Whenever you leave the lawnmower unat-

tended. Remove the key from models with elec-

tric starters.

– Replace all fuel tanks and containers caps

securely.

4) Substitute faulty silencers.

– Before refuelling.

5) Before use, always inspect the machine,

especially the condition of the blades, and

check that the screws and cutting assembly are

not worn or damaged. Replace worn or dam-

aged blades and screws in sets to preserve bal-

ance.

– Every time you remove or replace the grass-

catcher.

– Before adjusting the cutting heigh.

20) Reduce the throttle before turning off the

engine and turn the fuel off when you have fin-

ished mowing, following the instructions in the

engine handbook.

6) Before mowing, attach the discharge opening

guards (grass-catcher or stone-guard).

21) When mowing, always keep to a safe dis-

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

tance from the rotating blade. This distance is

the length of the handle.

•

Do not dispose of used lead-acid batteries in a

rubbish bin. Take them to a battery collection

point for recycling (applies to battery-powered

machines and machines with battery start).

Replace the silencer if faulty. When carrying out

repairs, always use original spare parts.

If the machines was originally equipped with a

catalyser which is now faulty, a new one must

be fitted when the silencer is replaced.

Always seek professional help when the carbu-

rettor requires adjustment.

Clean the air filter according to the directions.

When, after many years of service, your

machine needs to be replaced or is no longer

required, we recommended that the machine is

returned to your distributor for recycling.

D) MAINTENANCE AND STORAGE

•

1) Keep all nuts, bolts and screws tight to be

sure the equipment is in safe working condition.

Regular maintenance is essential for safety and

performance.

2) Never store the equipment with fuel in the

tank inside a building where vapour may reach

a flame or a spark or a source of extreme heat.

3) Allow the engine to cool before storing in an

enclosed space.

4) To reduce the fire hazard, keep the engine,

exhaust silencer, battery compartment and fuel

storage area free of grass, leaves, or excessive

grease. Do not leave containers with grass cut-

tings in rooms.

5) Check the stone-guard and grass-catcher

frequently for wear and deterioration.

•

6) If the fuel tank has to be drained, this should

be done outdoors and when the engine is cool.

7) Wear strong work gloves when removing and

reassembling the blade.

8) Check the blade’s balance after sharpening.

9) For reasons of safety, do not use the equip-

ment with worn or damaged parts. Parts are to

be replaced and not repaired. Use genuine

spare parts (blades should always bear the

PRODUCT IDENTITY

The identity of the product is determined by the

article and serial numbers of the machine.

These can be found on the label fixed to the chas-

sis of the machine:

symbol

). Parts that are not of the same qual-

ity can damage the equipment and be danger-

ous for your safety.

10) Whenever the machine is to be handled,

transported or tilted you must:

ART. NR

➔

SERIE NR.

– wear strong working gloves;

– grasp the machine at the points that offer a

safe grip, taking account of the weight and its

distribution.

Use this identification whenever you contact a

service workshop or buy replacement parts.

As soon as possible after buying the machine,

write the above numbers on the back page of this

booklet.

THE ENVIRONMENT

In order to protect the environment, we recom-

mend that the following points should be given

special consideration:

The manufacturer reserves the right to make

changes to the product without prior notice.

•

Always use pure unleaded petrol.

Always use a funnel and/or a petrol can with a

level control to avoid spillage when refilling the

fuel tank.

Do not fill the fuel tank completely.

Do not overfill with engine and/or transmission

oil.

When changing the oil, ensure that all the used

oil is collected. Avoid spillage. Take the used oil

to a recycling unit.

Do not dispose of used oil filter in a rubbish bin.

Take it to a recycming unit.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

IMPORTANT

INSTALLATION

For the instructions relative to the engine and

the battery, please read the relevant instruction

handbooks.

LOOSE PARTS IN THE BOX

2 brackets for the grass collector

4 screws for the brackets

1 Allen key

1 socket wrench

+ Instruction books

SYMBOLS

The following symbols can be found on the

machine to remind you of the care and attention

that are required during use.

HANDLE

1. Fold up the lower part of the handle.

The symbols mean:

2. Secure the upper part of the handle with wash-

ers and locking wheels. There is a lug on the

right hand side for the starter handle (fig. 1).

Important: Read the instruction handbook

before using the

3. Then tighten the locking wheels onto the lower

part of the handle. When these have been tight-

ened, the height of the handle can be adjusted

by tightening the screws A with the wrench pro-

vided. (fig. 2)

Warning! Keep onlookers away. Beware of

objects being flung out.

CABLE HOLDER

Warning! Keep hands and feet clear of the

cutting deck when the machine is running.

Secure the cables in the cable holders (fig. 3):

D: Start/Stop cable + Clutch cable

E: Throttle cable + Clutch cable

Warning! Before starting any repair work,

remove the spark plug cable from the spark

plug.

GRASS COLLECTOR

Warning! Always tilt the lawnmower

backwards when cleaning the

Raise the collector flap and attach the two brack-

ets to the grass collector with the screws provided.

The brackets are marked with «L» and «R» and

should be installed at the corresponding mark on

the rear of the mower (fig. 4).

underside. Petrol and oil can run out

if the lawnmower is tilted in the other direction.

Fit the fabric bag over the steel frame and then

snap the bag onto the plastic lid (fig. 5).

INTRODUCTION

Open the flap on the machine and attach the grass

collector to the brackets.

P O

S T

NOTE! The lawnmower can be operated without

the grass collector. The grass is then left in a line

behind the machine.

USING THE MOWER

COMBI

Your new lawnmower combines two different func-

tions in the same machine:

1. “MULCHING“

Start/Stop loop

Throttle control

Clutch loop

The machine comes equipped with a plug (P),

installed in the ejector opening (fig. 6). The machine

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

can be used for ‘Mulching’ i.e. the blade finely cuts

up the grass during mowing. The grass then falls

into the lawn where it is allowed to rot.

This provides the lawn with nourishment.

To remove the plug, press in the catch (R - fig. 6).

On reinstalling the plug ensure that both pins are

pressed firmly into the holes so that the plug snaps

in place.

REAR WHEEL DRIVE (*)

Engage the drive by pressing the clutch loop J

towards the handle. Disengage the drive by releas-

ing the clutch loop J (fig. 7).

CUTTING HEIGHT

2. COLLECTION

Do not set the cutting height so low that

the blade(s) come into contact with

uneven ground.

Assemble the grass collector provided (fig. 5).

Open the flap, remove the plug and instead hook

the collector onto the rear of the machine.

When mowing, the grass is collected in the collec-

tor.

Empty the grass onto the compost heap or spread

it over borders as fertiliser. The machine is also

ideal for collecting up leaves in the autumn.

The mower has single-lever control for adjusting

the cutting height. Pull the lever out, and set the

cutting height to one of the nine positions best

suited to your lawn (fig. 8).

3. REAR EJECTION

MAINTENANCE

Use the mower without the plug or the grass col-

lector (flap closed). The grass is released behind

the machine without being cut up.

IMPORTANT – Regular, careful maintenance is

essential for keeping the safety level and origi-

nal performance of the machine unchanged in

time.

STARTING THE ENGINE

Wear strong working gloves during any cleaning,

maintenance or adjustment operation on the

machine.

1. Place the lawnmower on flat, firm ground. Do

not start in long grass.

Should it be necessary to access the lower part,

only tilt the machine from the side shown in the

engine handbook; following the relative instruc-

tions.

2. Make sure the spark plug cable is connected to

the spark plug.

3. Press in the Start/Stop loop G towards the han-

dle. NOTE! The Start/Stop loop G must be kept

pressed in to prevent the engine stopping (fig.

7).

CLEANING

4. Grasp the starter handle and start the engine by

pulling briskly on the starter cord.

Carefully clean the machines with water after each

cut; remove the grass debris and mud accumulat-

ed inside the chassis to avoid their drying and thus

making the next start-up difficult.

5. For the best mowing results, the engine should

always be driven at full throttle.

The paintwork on the inside of the chassis may

peel off in time due to the abrasive action of the cut

grass; in this case, intervene promptly by touching

up the paintwork using a rustproof paint to prevent

the formation of rust that would lead to corrosion of

the metal.

STOPPING THE ENGINE

The engine may be very warm immedi-

ately after it is shut off. Do not touch the

silencer, cylinder or cooling flanges. This

can cause burn injuries.

Remove the transmission casing by removing the

screws S (fig. 9) and clean around the transmission

and drive belts with a brush or compressed air

once or twice a year.

Release the Start/Stop loopG (fig. 7) to stop the

engine.

Once every season, the drive wheels should be

cleaned internally. Remove both wheels.

If the start/stop loop ceases to work,

stop the engine by removing the spark

plug cable from the spark plug.

Immediately take the lawn mower to an

authorised workshop for repair.

Clean the gear wheel and the wheel gear rim of

grass and dirt using a brush or compressed air (fig.

10).

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

LUBRICATING DRIVE SHAFT

STORAGE

Once per season, the wedge on the drive shaft

should be greased. Remove the wheel (wheel cap,

screw and washer).

The same petrol must not remain in the tank for

more than one month.

Then remove the circlip and washer so that the

gear wheel can be removed from the shaft.

Lubricate the wedge with universal grease.

Thoroughly clean the mower and store it indoors in

a dry place.

Reinstall the wedge (the wedge is installed differ-

ently on the right and left side, fig. 11 - 12). Install

the gear wheel so that the «L» faces out on the left

side and the «R» faces out on the right side

(machine viewed from the rear).

SERVICING

Genuine spare parts are supplied by service work-

shops and by many dealers.

We recommend that you take the machine to an

authorised service station for annual servicing,

maintenance and inspection of safety equipment.

ADJUSTING CLUTCH CABLE

If the drive does not engage when the clutch loop

is pressed against the handle, or if the lawnmower

feels cumbersome or slow, this may be because

the clutch in the transmission is slipping.

For service and spare parts, please contact the

dealer where the machine was purchased.

To rectify this situation, adjust the clutch cable as

follows (with the engine off):

1. When the clutch loop is released, it should be

possible to push the mower backwards without

any resistance. If this is not the case, screw in

the nipple T until the mower can be pushed (fig.

13).

2. When the clutch loop is pressed in approx. 2 cm

(position 1), there should be some resistance

when pushing the lawnmower. With the clutch

loop fully pressed in (position 2) it should not be

possible to push the mower. Unscrew the nipple

T until this position is achieved.

CHANGING BLADES

To replace the blade, undo the screw (fig. 14).

Fit the new blade so that the stamped logo is

turned up facing the blade holder (not facing the

grass).

Reinstall as illustrated. Tighten the screw properly.

Tightening torque 40 Nm.

When replacing the blade, the blade screw should

also be replaced.

SHARPENING THE BLADES

Sharpening of the blades must be done by wet

method grinding, using a whetstone or a grind-

stone.

For safety reasons, the blades should not be

sharpened on an emery wheel. A very high temper-

ature could cause the blades to become brittle.

Download from Www.Somanuals.com. All Manuals Search And Download.

..................................................................................................................................

✍

..................................................................................................................................

Download from Www.Somanuals.com. All Manuals Search And Download.

..................................................................................................................................

✍

..................................................................................................................................

Download from Www.Somanuals.com. All Manuals Search And Download.

..................................................................................................................................

✍

..................................................................................................................................

Download from Www.Somanuals.com. All Manuals Search And Download.

Multi Tech Systems Modem MT9234ZBA User Manual
NETGEAR Network Router D500 User Manual
Net Optics Switch N IDP POBPSX 001 N IDP POBPLX 002 User Manual
Network Technologies Network Card Adapter User Manual
NewAir Dishwasher ADW 2600W User Manual
Nextar Car Stereo System NCU101 User Manual
Olympus Camera Accessories C 5500 User Manual
Onkyo DVD Player DV SP503E User Manual
Onkyo Stereo Receiver TX nr838 User Manual
Panasonic All in One Printer KX MC6020CX User Manual