Miele Washer W3824WPS User Manual

Operating instructions

for Washing machine

W 3824 WPS

en - GB

To avoid the risk of accidents or

damage to the machine it is

essential to read these instructions

before it is installed and used for the

first time.

M.-Nr. 07 171 200

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Caring for our environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating the washing machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Washing environmentally and economically . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Energy and water consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

How to wash correctly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Final spin speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Rinse and interim spin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

To omit the final spin (Rinse hold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

To omit rinse and interim spin and the final spin (No u) . . . . . . . . . . . . . . . . . 19

Delay start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Garment care label symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Cancelling a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Interrupting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Changing a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Adding or removing laundry after a programme has started . . . . . . . . . . . . . . . . 28

Safety lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

The correct detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Washing with several components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Fabric conditioners and liquid starch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Automatic dispensing of fabric conditioner or liquid starch to laundry

at the end of a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Colour run and dye removers / dyes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

External casing and fascia panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Extra cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Cleaning the detergent dispenser drawer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Descaling the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning the filter in the water inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

The programme does not start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Fault messages in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

An unsatisfactory wash result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

The drum door does not open when you press the Door button. . . . . . . . . . . . . . 39

Opening the drum door in the event of a blocked drain outlet and/or power failure . 40

Blocked drain outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Appliance guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Installation surface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Installing the washing machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Removing the transit bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Re-fitting the transit bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Levelling the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Screwing out and adjusting the feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Building under a continuous worktop/in a kitchen run . . . . . . . . . . . . . . . . . . . 49

Washer and Dryer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

The Miele Waterproof system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Connection to the water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Connection to the drainage system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Notes for test institutes: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

To access programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

To select a programmable function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

To alter a programmable function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

To come out of programmable functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Language F. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Water plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Gentle action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Suds cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Temperature unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Standby display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Anti-crease. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

This washing machine is not

intended for use by persons (including

This washing machine conforms to

current safety requirements.

Inappropriate use can, however,

lead to personal injury and damage

to property.

children) with reduced physical,

sensory or mental capabilities, or lack

of experience and knowledge, unless

they are supervised whilst using it or

have been given instruction concerning

its use by a person responsible for their

safety.

To avoid the risk of accidents and

damage to the washing machine,

please read these instructions

carefully before using it for the first

time. They contain important

Safety with children

Keep children away from the

information on its installation, safety,

use and maintenance.

washing machine at all times. It is not a

toy! To avoid the risk of injury do not

allow children to play on or near it or to

play with its controls. Supervise

Keep these instructions in a safe

place and ensure that new users are

familiar with the content. Pass them

on to any future owner.

children whilst you are using it.

Older children may only use the

washing machine if its operation has

been clearly explained to them and

they are able to use it safely,

Correct application

Only use the washing machine to

wash items which are specified by the

manufacturer to be machine-washable

on the wash-care label, and textiles

composed of hand-washable wool or

wool blend fabrics as well as satin,

lace, silk and other hand-washable

garments. Any other applications may

be dangerous. The manufacturer

cannot be held liable for damage

resulting from incorrect or improper use

or operation.

recognising the dangers of misuse.

For machines with a 'porthole' door,

remember that the porthole glass will

be hot when washing at very high

temperatures.

Do not let children touch it.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

Technical safety

Unauthorised repairs could result in

unforeseen dangers for the user, for

which Miele cannot accept liability.

Repairs should only be undertaken by a

Miele approved service technician.

Ensure current is not supplied to the

machine until after maintenance or

repair work has been carried out.

Before setting up the washing

machine, check it for any externally

visible damage.

Do not install or use a damaged

washing machine.

Before connecting the washing

machine, ensure that the connection

data on the data plate (voltage and

connected load) match the mains

electricity supply. If in any doubt,

consult a qualified electrician.

If the connection cable is faulty it

must only be replaced by a Miele

approved service technician to protect

the user from danger.

In the event of a fault or for cleaning

purposes, the washing machine is only

completely isolated from the electricity

supply when:

The electrical safety of this washing

machine can only be guaranteed when

continuity is complete between it and

an effective earthing system which

complies with current local and national

safety regulations. It is most important

that this basic safety requirement is

present and regularly tested, and

where there is any doubt the household

wiring system should be inspected by a

qualified electrician. The manufacturer

cannot be held liable for the

– it is switched off at the wall socket

and the plug is withdrawn, or

– it is switched off at the mains, or

– the mains fuse is withdrawn, or the

screw-out fuse is removed (in

countries where this is applicable).

The Miele "Water protection system"

protects from water damage provided

the following conditions have been met:

– the machine is correctly plumbed in

and connected to the electricity

supply.

consequences of an inadequate

earthing system (e.g. electric shock).

Do not connect the washing

– if a fault has been identified, the

machine must be examined by a

competent person before further use,

and repaired if necessary.

machine to the mains electricity supply

by an extension lead. Extension leads

do not guarantee the required safety of

the appliance (e.g. danger of

overheating).

In countries where there are areas

which may be subject to infestation by

cockroaches or other vermin, pay

particular attention to keeping the

machine and its surroundings in a

clean condition at all times. Any

Faulty components must only be

replaced by genuine Miele original

spare parts. Only when these parts are

fitted can the safety standards of the

machine be guaranteed.

damage which may be caused by

cockroaches or other vermin will not be

covered by the machine guarantee.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

This washing machine may only be

Turn off the stopcock if the machine

is to be left for any length of time (e.g.

used in mobile installations such as

ships if a risk assessment of the

installation has been carried out by a

suitably qualified engineer.

holiday), especially if there is no floor

drain (gully) in the immediate vicinity.

Flooding danger.

If hooking the drain hose into a wash

basin, check that the water can drain

off quickly enough to prevent the sink

from overflowing. Make sure the drain

hose is secure, so that the force of the

water flowing out of the hose does not

dislodge it.

Correct use

Do not install your washing machine

in rooms where temperatures below

freezing may occur. Frozen hoses may

burst or split. The reliability of the

electronic control unit may be impaired

at temperatures below freezing point.

Take care to ensure that foreign

objects (e.g. nails, pins, coins, paper

clips) do not find their way into the

machine with the laundry. These may

damage components of the machine

(e.g. suds container, drum), which in

turn can result in damage to the

laundry.

Before using the washing machine

for the first time, check that the transit

bars at the rear of the machine have

been removed (see section on

"Installation"). During spinning, a transit

bar which is still in place may result in

damage to both the machine and

adjacent furniture or appliances.

If the correct amount of detergent is

dispensed, the machine should not

need to be descaled. If, however, you

do wish to descale the machine only

use proprietary non-corrosive descaling

agents and strictly observe the

instructions on the packaging. A

special descaling agent is available to

order from the Miele Spare Parts

Department or via the internet on

www.miele-shop.com.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety instructions

Textiles which have been

Only remove laundry from the

pre-treated in solvent based cleaning

agents must be thoroughly rinsed in

clean water before being washed in the moving drum is extremely dangerous

washing machine once the drum has

stopped turning. Reaching into a

machine.

and could result in injury.

Never use solvent based cleaning

agents, e.g. those containing benzene,

Accessories

in this machine, as this may result in

damage to component parts and create

toxic fumes. Such agents also pose a

fire and explosion hazard.

Accessory parts may only be fitted

when expressly approved by Miele. If

other parts are used, guarantee,

performance and product liability

claims will be invalidated.

Never use solvent based cleaning

agents, e.g. those containing benzene,

to clean the outside surfaces of this

machine. They can cause damage to

plastic surfaces.

Miele cannot be held liable for

damage caused by non-compliance

with these Warning and Safety

instructions.

Only use dyes specified by the

manufacturer as being suitable for use

in a domestic washing machine. Always

observe the manufacturer's instructions

carefully.

Colour run and dye removers

contain sulphur compounds which can

cause damage such as corrosion. Do

not use these products in this machine.

If liquid detergent comes into

contact with the eyes, rinse them

thoroughly with lukewarm water imme-

diately. If swallowed, seek medical

assistance immediately and retain the

packaging or label for reference. Those

with skin problems or sensitive skin

should avoid their skin coming into

contact with liquid detergent.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating the washing machine

Control panel

aExtra option buttons

Various extra options can be added

to the washing programmes.

fPC / Optical interface

This is used by service technicians

to run diagnostic checks on your

machine and can also be used to

update programming data in the

future.

bDisplay

See the following page for more

information.

gStart/Stop button

cDelay start button

For delaying the start time of a

programme.

For starting the programme selected

and cancelling a programme once it

has started.

dTemperature button

For selecting a temperature.

hProgramme selector

For selecting a programme. The

indicator light next to the selected

programme will come on. The

programme selector can be turned

clockwise or anti-clockwise.

eSpin speed button

For selecting the final spin speed or

e (Rinse hold) or No u (Without

spin).

iI-On/0-Off button

For switching the machine on or off.

jDoor button

Opens the machine door.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating the washing machine

Programme duration

After the start of a programme, the

estimated programme duration will

appear in the display in hours and

minutes.

When delay start is being used, the

programme duration will appear after

the delay start time has elapsed.

During the first 8 minutes the washing

machine measures how much water is

being absorbed by the laundry and

uses this to calculate the load. The

programme duration may be longer or

shorter depending on this absorbency

rate.

The following are selected via the

display:

– wash temperature

– spin speed

Delay start

– delay start

The delay start time selected will

appear in the display.

– cancellation of a programme

– safety lock

After the Start/Stop button has been

pressed, the delay start time will start

counting down. If the delay start time is

more than 10 hours, it will count down

by the hour. If it is less than 9 hours and

59 minutes it will count down minute by

minute.

– programmable functions

The display also shows:

– the programme duration

– the programme sequence

Once the delay start time has elapsed,

the programme begins and the

estimated programme duration shows

in the display.

Programmable functions

The programmable functions can be

used to tailor washing programmes to

suit your individual requirements. In

programming mode, the display will

show the function selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

Setting the language

Before using the machine for the first

time ensure that it is correctly

installed and connected. See

"Installation and connection". Also

check that the drain filter is securely

tightened to prevent the risk of water

leaks during use.

You will be asked to select the

language you require for the display. It

is possible to change the language at

any time via the programmable

functions.

deutsch

^ If the language shown is not the one

you want, select the language you do

want by turning the programme

selector. Confirm your selection by

pressing the Start/Stop button.

This washing machine has

undergone a thorough functional test

in the factory and there will be some

residual water in the drum from this

process.

Reminder to remove transit bars

For safety reasons, spinning is not

possible until the machine has been

prepared for using for the first time. To

activate the spinning function you must

run a wash programme without laundry

and without detergent.

To avoid the risk of damage, the

transit bars must be removed before

the machine is used for the first time.

See "Installation and connection" for

instructions on how to do this.

Using detergent could result in an

excessive build-up of foam.

^ After removing the transit bars (if this

has not already been done by your

fitter), press the Start/Stop button.

This also activates the ball valve. The

ball valve prevents detergent escaping

from the suds container into the sump

during a wash programme, thus making

maximum use of the detergent.

Running your first programme

Run a Cottons 60°C programme without

any laundry and without detergent.

^ Press the I-On/0-Off button in.

^ Open the stopcock.

If the washing machine is being

switched on for the first time, the

welcome screen will appear.

^ Press the Start/Stop button.

^ At the end of the programme switch

the machine off.

The welcome screen will appear in

the display every time the machine is

switched on until a programme

lasting longer than 1 hour has been

completed.

The machine is now ready for use.

Download from Www.Somanuals.com. All Manuals Search And Download.

Washing environmentally and economically

Energy and water consumption

Detergent

– Water consumption and energy

usage are determined by the size of

the load.

– Do not exceed the amounts of

detergent recommended by the

manufacturer on the packaging.

To make the most out of your

machine, load the maximum dry load

for the programme you are using.

– Adjust the dosage to the degree of

soiling of the laundry.

– Reduce the amount of detergent with

smaller loads (approx. ¹/₃less than

the amount recommended can be

used when washing a half load).

– Use the Automatic and Express

programmes for small loads.

– When smaller amounts of laundry are

washed using the Cottons

programme, the automatic load

recognition system will reduce the

amount of water, time and energy

used. This may mean that the time

left shown in the display is adjusted

during the course of the wash

programme.

Choosing the correct extra option

(Short and Pre-wash)

Select:

– A wash programme together with the

Short extra option for light to normal

soiling where there are no obvious

marks.

– Using the Cottons 60°C programme,

instead of the Cottons 95°C

– A wash programme without any extra

options for normal to heavy soiling

with visible staining.

programme will give energy savings

of between 35% and 45%. This is

sufficient for most levels of soiling.

– The Pre-wash extra option for laundry

with large amounts of dirt (e.g. dust,

sand).

When drying with a tumble dryer

Selecting the highest possible spin

speed for the wash programme will

save energy when drying in a tumble

dryer afterwards.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to wash correctly

Brief instructions

,^{If you use a solvent-based clean-}

ing agent (e.g. one containing ben-

zene) to pre-treat a stain, make sure

that any plastic parts (e.g. buttons)

are protected, and that the cleaning

agent is rinsed off before washing the

garment in the machine.

The headings numbered A, B, C, . . .

show the operating sequence and can

be used as brief instructions.

ASort the laundry

,^{Do not use solvent-based}

cleaning agents in this machine.

^ Sort the laundry by colour and by

care label. Most garments have a

textile care label in the collar or side

seam.

Dark textiles often contain excess dye

and should be washed separately

several times before being included in

a mixed load. Always wash whites and

coloureds separately.

^ Empty all pockets.

,^{Foreign objects (e.g. nails,}

coins, paper clips, etc.) can cause

damage to garments and

– Curtains: Remove lead weights first

or place in a laundry bag.

components in the machine.

– Underwiring and collar stiffeners:

Any loose wiring in bras, shirt collar

stiffeners, etc. should be removed or

sewn in.

^ Badly soiled areas, stains etc. should

be cleaned as soon as possible,

preferably whilst still fresh. Spillages

should be carefully dabbed off using

a soft colourfast cloth. Do not rub!

– Knitted garments, trousers and

jeans, T-shirts and sweat shirts: Turn

inside out, if recommended by the

manufacturer.

Badly soiled areas can be pre-treated

with liquid detergent, stain removers

etc. first, following the manufacturer's

instructions. With particularly stubborn

stains ask your dry cleaner for advice.

– Close any zips, fasten hooks and

eyes etc before washing.

– Fasten duvet covers etc. to prevent

small items from being rolled up

inside them.

Do not wash any items in this machine

which are specified by the

manufacturer as not washable on the

care label. (h symbol)

Download from Www.Somanuals.com. All Manuals Search And Download.

How to wash correctly

BSwitch on the washing machine

DSelect a programme

CLoad the drum

^ Press the Door button to open the

drum door.

^ Unfold the laundry and load loosely

in the drum. Mixing both large and

small items gives better wash results

and also helps distribute the load

evenly during spinning.

The most efficient use of energy and

water is achieved when a full load is

washed. However, do not overload as

this causes creases and reduces

cleaning efficiency.

^ Turn the programme selector

clockwise or anti-clockwise to the

required programme. The

Make sure that no garments are

caught between the drum door and

seal.

programme indicator light for the

programme selected will come on.

ESelect a temperature / spin speed

The suggested temperature and/or spin

speed can be changed.

1:49

60°

1600

^ Press the Temperature button to alter

the temperature and press the Spin

speed button to alter the spin speed.

^ Shut the door with a gentle swing.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to wash correctly

FSelect an extra option(s)

Water plus

The water level in the main wash and

the rinses will be increased if the Water

plus option is selected.

However, you can select other settings

for Water plus. These are described in

"Programmable functions".

Pre-wash

For laundry with large amounts of dirt

e.g. dust, sand.

Buzzer

^ Select any extra options by pressing

the appropriate button. The relevant

indicator light will come on to show

which extra option has been

selected.

An audible tone sounds repeatedly at

the end of a programme and when

Rinse hold is reached. The buzzer will

sound repeatedly until the machine is

switched off. The volume of the buzzer

can be changed, see "Programmable

functions".

Not all the extra options are suitable for

use with every programme.

You can only select extra options which

are compatible with the basic

programme being used.

GSelect Delay start (if required)

The start of a programme can be

delayed from 30 minutes up to 24

hours, allowing you to make use of

night-time economy electricity rates, for

example.

Short

For light to normal soiling with no visible

staining.

See "Delay start" for more information.

The duration of the main wash is

reduced.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to wash correctly

HAdd detergent

It is important to dispense the correct

amount, because . . .

. . . too little detergent results in:

– Laundry not getting properly clean

and with time it may become grey

and hard to the touch.

– Greasy particles clinging to the

laundry.

– Limescale deposits on the heater

elements.

^ Pull out the detergent drawer and

place detergent in the compartments

as follows:

. . . too much detergent results in:

– Excessive foam which causes a low

level of agitation and poor wash,

rinse and spin results.

Detergent for the pre-wash (divide

the total recommended amount as

follows: add ¹/₃to compartment i

and ²/₃to compartment j)

– Higher water consumption (an

additional rinse cycle will

automatically switch in).

– A burden to the environment.

Detergent for the main wash

Fabric conditioner or liquid starch

^ Close the detergent drawer.

See "Detergent" for further information.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to wash correctly

IStart the programme

Check that all items have been

removed from the drum. Items left in

the drum could discolour other items

in the next wash or become

^ Press the flashing Start/Stop button.

If a delay start time has been selected,

then this will count down in the display.

At the end of the delay start time or im-

mediately after the programme has

started (if no delay start time has been

selected) the estimated programme

duration will appear in the display.

During the first 8 minutes the machine

measures how much water is being

absorbed by the laundry. The

discoloured themselves.

programme duration may be longer or

shorter depending on this absorbency

rate.

The programme sequence is also

shown in the display. The washing

machine shows you when each section

of the programme is reached.

^ Check the folds in the door seal for

any small articles, e.g. buttons, which

might be lodged there.

JRemove the laundry when the

programme has finished

^ Switch the machine off with the

In the anti-crease phase after the

programme has finished, the following

will appear alternately in the display:

I-On/0-Off button.

^ Close the drum door. Otherwise there

is the danger of objects being placed

inadvertently in the drum. If these

remained unnoticed and were

washed in the next load, they could

damage the laundry.

0:00 Anti-crease

and

0:00 Finish

^ Press the Door button to open the

drum door.

^ Remove the laundry.

Download from Www.Somanuals.com. All Manuals Search And Download.

Spinning

Final spin speed

To omit the final spin (Rinse hold)

Programme

Cottons

rpm

1600

1200

600

^ Select the e setting using the Spin

speed button. The laundry will not be

spun and will remain suspended in

the final rinse water. This reduces

creasing if the laundry is not going to

be removed from the drum immedi-

ately after the end of the programme.

Minimum iron

Delicates

Woollens

Silks

1200

400

Express

1600

1200

600

– To start the final spin:

Automatic

Shirts

The washing machine will display the

maximum spin speed possible. You

can select a spin speed lower than

this. Start the final spin by pressing

the Start/Stop button.

Denim

900

Outerwear

Dark garments

Spin

800

1200

1600

– To end the programme:

You can reduce the final spin speed.

However, you cannot select a final spin

speed higher than that shown in the

chart above.

Press the Door button. The water will

drain away. Press the Door button

again to open the door.

To omit rinse and interim spin and

Rinse and interim spin

the final spin (No u)

There is a spin after the main wash and

between the rinses. A reduction in the

final spin speed will also reduce the

interim spin speed. If a spin speed of

less than 700 rpm is selected for a

Cottons programme, an additional rinse

is introduced.

^ Select the No u setting using the

Spin speed button. The laundry is not

spun after the final rinse. The water

will drain away and the machine will

go straight into the anti-crease stage.

An additional rinse is introduced if

this setting is selected with the

Cottons, Minimum iron, Express and

Automatic programmes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Delay start

Delay start allows you to choose when

you want the programme to start. The

start of a programme can be delayed

from 30 minutes up to a maximum of 24

hours, allowing you to make use of

night-time economy electricity rates, for

example.

Altering delay start

You can change the delay start time at

any time by pressing the Delay start

button.

Cancelling delay start before delay

start has been activated

Selecting delay start

^ Press the Delay start button until

24 h appears in the display. Then

press the Delay start button again

briefly to cancel delay start.

^ Press the Delay start button. The

following will appear in the display:

0:30 ,

60°

1600

If you cancel delay start after the delay

start time has started counting down,

the washing programme will start imme-

diately.

^ Each press on the Delay start button

increases the delay start time:

– in 30 minute steps up to 10 hours,

– in 1 hour steps from 10 hours

upwards.

If you keep the Delay start button

pressed in, the time will continue to

count up to 24 hours.

Activating delay start

^ Press the Start/Stop button to activate

delay start. The following will appear

in the display:

4:30 , until start

After the delay start time has elapsed,

the washing programme will start and

the estimated programme duration and

the programme sequence will show in

the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme chart

Cottons 9ö8E76*

Fabric

30°C to 95°C

Max. load 6.0 kg

Cottons, linens or cotton mix fabrics, e.g. table linen, towelling,

underwear, T-shirts etc.

Extra options Short, Water plus, Pre-wash

Note for test institutes:

Short programme: 3.0 kg load and Short extra option

Minimum iron

30°C to 60°C

Max. load 3.0 kg

43218E76*

Fabric

Synthetics, mixed fibres and easy care cottons. If fabrics have a

high proportion of man-made fibres it is advisable to programme

the machine for "Gentle action". See "Programmable functions".

Note

Reduce the spin speed for fabrics which crease easily.

Extra options Short, Water plus, Pre-wash

Delicates 4321ac* cold to 60°C

Max. load 2.0 kg

Fabric

For delicate garments made of synthetic fibres, mixed fibres,

rayon and easy care cottons.

Curtains, including net curtains, specified as machine-washable

by the manufacturer.

Notes

– Dust in curtains usually makes using a programme with

pre-wash advisable.

– For curtains which crease easily, reduce the spin speed or

deselect the spin.

Extra options Short, Pre-wash

Woollens /ac*

cold to 40°C

Max. load 2.0 kg

Fabric

Machine-washable or hand-washable wool or wool blend fabrics.

If the care label does not specify a temperature, wash using the

cold setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme chart

Silks /c*

cold to 30°C

Max. load 1.0 kg

Fabric

Silks and other handwashable fabrics with no wool content, e.g.

satin, lace and silk.

Note

Place tights, bras etc. in a washing bag.

Extra option Water plus

Express 76*

cold to 40°C

Max. load 3.0 kg

Fabric

Small loads of items which require freshening up and which can

be washed in a Cottons programme.

Note

This programme can be used for rinsing individual items. Select

the cold setting, and do not add any detergent.

Extra option Water plus

Automatic 7621*

cold to 40°C

Max. load 3.5 kg

Fabric

Mixed loads of garments suitable for the Cottons and Minimum

iron programmes. Sort according to colour.

Note

The wash parameters (e.g. water level, wash rhythm and spin

speed) are adjusted automatically in this programme to ensure

the best possible care and wash result for each item.

Shirts

cold to 60°C

Max. load 2.0 kg

Notes

– Pre-treat collars and cuffs if necessary.

– Wash silk garments in the Silks programme.

Extra options Short, Water plus

Denim

cold to 60°C

Max. load 3.0 kg

Notes

– Wash denim inside out.

– Denim often contains excess dye and will run during the first

few washes. Wash light and dark coloured items separately.

Extra options Short, Pre-wash

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme chart

Outerwear

cold to 40°C

Max. load 2.0 kg

Garment

Outerwear made from micro-fibres such as Gore-Tex^®,

SYMPATEX^®, WINDSTOPPER^®etc.

Notes

– Zip up jackets before washing.

– Do not use fabric conditioner.

Extra options Short, Water plus, Pre-wash

Dark garments cold to 40°C

Max. load 3.0 kg

Item

Note

Black and dark garments made from cotton or mixed fibres.

Wash inside out.

Extra option Short

Spin

Notes

– Drain only: Select No u.

– Make sure you select the appropriate spin speed.

* Please note that the "buckets" represent garment care label symbols. See

"Garment care label symbols".

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme sequence

Main wash

Rinses

Spinning

Water

level

Wash

Water Rinses Interim

Final

spin

rhythm

level

(

–

spin

–

Cottons

(

–

2-4¹⁾

Minimum iron

Delicates

Woollens

Silks

2-3²⁾

–

Express

Automatic

Shirts

2-3²⁾

–

abc

Denim

–

Outerwear

Dark garments

Spin

L³⁾

–

d = Low water level

a= Intensive rhythm

b= Normal rhythm

c= Gentle rhythm

d= Sensitive rhythm

( = Medium water level

e = High water level

e= Handwash rhythm

See the following page for more information about the programme sequences.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme sequence

This machine has fully electronic

controls with automatic load

Special features in the programme

sequences:

recognition. It takes in the right amount

of water required for the programme

depending on the amount of laundry

and its absorbency rate. This means

that programme cycles and durations

can vary.

Anti-crease:

At the end of every programme, with

the exception of the Woollens

programme, the drum continues to turn

at intervals for up to 30 minutes to help

prevent creasing. The door can be

opened and laundry removed at any

time during the anti-crease phase.

The programme sequences outlined in

the chart are based on the basic

programme with a full load. Extra

options which can be selected have not

been taken into account.

A second rinse is carried out when a

temperature of 60°C to 95°C has

been selected. A third rinse is

carried out when a temperature

below 60°C is selected.

The display shows the stage the

programme has reached.

A third/fourth rinse is carried out if:

– there is too much foam in the drum

– a spin speed lower than 700 rpm has

been selected

– No u has been selected

A third rinse takes place

automatically if:

No u has been selected

In the Outerwear programme,

laundry is only spun after the main

wash.

Download from Www.Somanuals.com. All Manuals Search And Download.

Garment care label symbols

Washing

Ironing

The figure quoted in the bucket is the

maximum temperature the garment

can be washed at. The number of

bars under the symbol indicates the

level of agitation permitted.

The number of dots indicates the

ironing temperature

Hot iron (max sole plate temp.

approx. 200°C)

Medium hot iron (max sole

plate temp. approx. 150°C)

No bar under the symbol: =

normal agitation

Cool iron (max sole plate

temp. approx. 110°C). Do not

steam iron garments carrying

this symbol.

One bar under the symbol: =

reduced agitation

Two bars under the symbol: =

much reduced agitation

Do not iron

Hand wash (if no temperature

is specified use the lowest

temperature or cold)

Professional cleaning

Dry clean only. The letters

indicate the type of cleaning

agent required.

Do not wash

Professional Wet Clean only

Do not dry clean

Drying

The number of dots indicates the

drying temperature

Bleaching

Normal temperature

Low temperature

Do not tumble dry

{

Any oxidising bleaching

agent can be used

Only use an oxygen based

bleach or a non-chlorine

bleach

Do not bleach

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the programme sequence

Cancelling a programme

Changing a programme

You can cancel a programme at any

time after it has started.

After the start of a programme it is no

longer possible to select a different

programme.

^ Press the Start/Stop button.

Temperature

Cancel programme

It is possible to select a different

temperature up to 5 minutes after the

programme has started.

^ Press the flashing Start/Stop button

again.

The suds will be pumped away.

If you want to remove the laundry:

^ Press the Door button.

^ Press the Temperature button.

Spin speed

It is possible to change the spin speed

up until the final spin begins.

If you want to select a different

programme:

^ Press the Spin speed button.

^ Switch the machine off with the I-On/

0-Off button.

Extra options

^ Switch the washing machine back on

It is possible to select or deselect the

Short and Water plus extra options up

to five minutes after the programme has

started.

again.

^ Check that there is still detergent in

the detergent drawer. Add detergent,

if necessary.

A programme cannot be cancelled

or changed if the safety lock has

been activated.

^ Select and start a new programme.

Interrupting a programme

^ Switch the machine off with the I-On/

0-Off button.

To continue with the same programme:

^ Switch the machine back on with the

I-On/0-Off button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the programme sequence

Adding or removing laundry

after a programme has started

Safety lock

The safety lock prevents the machine

from being opened, the programme

from being cancelled or the machine

from being switched off during a

wash programme.

^ Press the Door button to open the

drum door.

^ Add or remove items.

^ Close the drum door.

To activate the safety lock

The programme will continue

automatically.

^ Press and hold in the Start/Stop

button after the programme has

started.

Please note:

Once a programme has started the

machine cannot recognise any

adjustment to the load.

Stop or in 3 secs 0

^ Keep the Start/Stop button pressed in

until the time has elapsed and the

following appears in the display:

For this reason, if laundry is added or

removed after the start of a programme,

the machine will always complete the

programme cycle assuming a full load

which can lead to an increase in the

programme duration shown in the

display.

Locked 0

The safety lock is now activated. It is

deactivated automatically at the end of

the programme.

The door cannot be opened, if:

To deactivate the safety lock

– the suds temperature is above 55°C.

– the water is above a certain level.

^ Press and hold in the Start/Stop

button after the programme has

started.

– the programme has reached the

Unlock in 3 secs 0

Final spin stage.

^ Keep the Start/Stop button pressed in

until the time has elapsed and the

following appears in the display:

If you press the Door button when the

above conditions are present, the

following will appear in the display:

Unlocked 1

Door locked

Download from Www.Somanuals.com. All Manuals Search And Download.

Detergent

The correct detergent

All modern detergents produced for automatic washing machines are suitable.

Use dispensing aids, e.g. balls, if these are supplied with the detergent. Tablets

are suitable for full loads, but note that it may be impractical to reduce tablets for

smaller loads. Some tablets do not dissolve as rapidly as others, and may not be

suitable for programmes with short durations. Do not use biological detergents on

silk, as the enzymes may damage the silk. Instructions for use and recommended

dosage amounts are given on the detergent packaging.

Liquid detergent should be dispensed using a ball provided by the manufacturer

for programmes without a pre-wash.

For programmes with a pre-wash you will need to purchase a special container

from the Miele Spare Parts department which sits in the main wash compartment

j of the detergent dispenser drawer. Add liquid detergent to this container for

the main wash and to compartment i for the pre-wash.

All purpose

detergent for

whites*

Detergent for

delicates

coloured fabrics*

Cottons

Minimum iron

Delicates

Woollens

Silks

Liquid detergent for machine-washable woollens

Liquid detergent for machine-washable silk and woollens

Express

Automatic

Shirts

Denim

X¹⁾

Outerwear

Dark garments

X¹⁾

1) Only use liquid detergent

* Powder detergent, tablet detergent, liquid detergent and liquid tab detergent

Download from Www.Somanuals.com. All Manuals Search And Download.

Detergent

The right amount to dispense will

depend on the following:

Water softener

A water softener can be used to cut

down on the use of detergents in hard

water areas. Dispense according to the

amount specified on the packaging.

First add detergent and then the water

softener.

– The quantity of laundry

– The soiling level of the laundry

Lightly soiled

No visible dirt or stains. Possibly

slight body odour.

Miele branded water softening tablets

are available from the Miele Spare Parts

Department or via the internet on

www.miele-shop.com.

Normally soiled

Visibly dirty and/or just a few slight

stains.

Heavily soiled

Use a quantity of detergent as for soft

Visible dirt and stains and/or dried on water.

soiling.

Miele do not recommend connecting

– The water hardness level.

Check with your local water supplier

if you do not know the hardness level

in your area.

the machine to a household water

softener.

Washing with several

components

If you wash using several components

(e.g. special application detergents),

we recommend always dispensing the

agents into compartment j in the

following order:

1. Detergent

2. Water softeners

3. Stain remover

This way the agents are distributed

more evenly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Detergent

Fabric conditioners and liquid

starch

If starching frequently, thoroughly

clean the dispenser compartment,

especially the siphon tube and the

fabric conditioner channel, regularly.

See "Cleaning the detergent

Fabric conditioners

make garments soft to handle and help

prevent static cling when tumble

drying.

dispenser drawer". Do not use

powder starch formulations or

viscous liquid starch in the §

compartment as it will clog up.

Starch

stiffens and gives body to items of

laundry, e.g. shirts, tablecloths and bed

linen.

Colour run and dye removers /

dyes

Automatic dispensing of fabric

conditioner or liquid starch to

laundry at the end of a programme

^ Do not use colour run or dye

removers in this machine.

^ Dyes suitable for use in domestic

washing machines can be used.

However, please note that the salt

used in the dyeing process can

cause corrosion to stainless steel

components in the machine if you

dye frequently. Always observe the

manufacturer's instructions carefully.

^ Add the fabric conditioner or liquid

starch to compartment §. Do not

exceed the maximum level mark.

It will be automatically dispensed in the

last rinse. At the end of the programme

a small amount of water remains in the

fabric conditioner compartment §.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Extra cleaning

,^{Disconnect the machine from the}

mains electricity supply and

Carry out a hot wash (70°C or above)

with powder detergent approx. every 6

weeks to help prevent deposits building

up in the machine. These can occur

when washing is mainly done at low

temperatures, and also lead to

withdraw the plug from the socket

before cleaning the machine.

,^{The washing machine must not}

be hosed down.

unpleasant smells. If you have no

reason to wash occasionally at this high

temperature, then run a Cottons 95°C

programme with detergent but no

laundry at regular intervals.

A range of Miele branded cleaning and

conditioning agents are available to

order from your Miele dealer, the Miele

Spare Parts Department, or via the

internet on www.miele-shop.com

Cleaning the detergent

dispenser drawer

External casing and fascia

panel

Remove detergent residues regularly.

Clean the casing using a Miele E-Cloth,

or with a mild non-abrasive cleaning

agent or soap and water using a well

wrung-out cloth. Wipe dry with a soft

cloth.

^ The drum and any stainless steel

outer panels can be cleaned using a

suitable proprietary stainless-steel

cleaning agent following the

manufacturer's instructions on the

packaging.

^ Pull out the detergent dispenser

drawer until a resistance is felt. Press

down the release catch and at the

same time pull the drawer right out of

the machine.

,^{Do not use solvents, abrasive}

cleaners, glass cleaners or

all-purpose cleaning agents.

These might damage plastic

surfaces and other components

because of the chemicals they

contain.

^ Clean the detergent drawer with

warm water.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Cleaning the detergent dispenser

drawer housing

^ Clean the siphon.

1. Remove the siphon from

compartment § and rinse under

warm running water. Clean the

siphon tube in the same way.

^ Use a bottle brush to remove

detergent residues and limescale

from the jets inside the detergent

dispenser drawer housing.

2. Replace the siphon.

Descaling the machine

If starching frequently, thoroughly

clean the siphon and siphon tube

regularly. A build-up of starch will

cause them to get clogged.

If the correct amount of detergent is

dispensed, the machine should not

need to be descaled. If, however, you

do wish to descale the machine only

use proprietary non-corrosive descaling

agents and strictly observe the

instructions on the packaging.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Cleaning the filter in the water

inlet

^ First turn off the stopcock.

^ Unscrew the threaded union

connecting the free end of the inlet

hose to the stopcock.

The washing machine has a filter to

protect the water inlet valve.

The accessible filter in the union in the

open end of the inlet hose should be

checked every six months, or more

often if there are frequent interruptions

to the external water supply.

^ Remove the rubber seal 1 from the

recess.

^ Using pointed pliers, take hold of the

plastic filter bar 2 and remove.

^ Clean the plastic filter.

^ Put the filter and seal back in the

reverse order and reconnect the

hose.

Turn on the stopcock and check the

connection is watertight. If water drips

out, tighten the connection.

Never forget to put the filter back in

place after cleaning.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

With the help of the following notes, minor faults in the performance of the

machine, some of which may result from incorrect operation, can be put right

without contacting the Service Department.

,^{Repair work to electrical appliances should only be carried out by a}

suitably qualified person in strict accordance with current local and national

safety regulations. Repairs and other work by unqualified persons could be

dangerous. The manufacturer cannot be held liable for unauthorised work.

The programme does not start

Problem

Possible cause

Remedy

Check whether

The display remains

dark, and the Start/

Stop button indicator

light does not come

on.

There is no power to

the machine.

– the mains plug is plugged

in and switched on.

– the fuse or circuit breaker

has tripped.

You are asked to enter Access via a code has Enter the code and confirm

a code.

been activated.

the entry. Deactivate the code

if you do not wish this

message to appear in the

display the next time the

machine is switched on.

The display is dark.

The display has

switched off

Press a button. Standby

comes to an end.

automatically to save

energy (Standby

mode).

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

Fault messages in the display

Problem

Possible cause

Remedy A

; lights up in the

display and

– The water outlet is

blocked or

– Clean the drain filter and

the drain pump.

Drain fault

restricted.

– The maximum delivery

head is 1 m.

flashes.

– The drain hose has

been fixed too high.

; lights up in the

display and

– The water inlet is

blocked or

Check whether

– the stopcock is opened

properly.

Water inlet

fault

restricted.

– the inlet hose is kinked.

flashes.

–

the water pressure is too

low.

; lights up in the

display and

The water protection

system has reacted.

Call the Service Department.

Waterproof

fault

flashes.

; lights up in the

display and

There is a fault.

Start the programme again.

If the fault message appears

again, contact the Service

Department.

Technical

fault

flashes.

Anti-crease

Excessive foam has

built up during

washing.

Use less detergent next time

and follow the manufacturer's

instructions on dosage given

on the packaging.

Chk detergent

flashes in the display.

ATo switch off the fault message: Switch the machine off with I-On/0-Off button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

General problems

Problem

Possible cause

Remedy

The machine shakes

during the spin cycle.

The machine feet are not Level the machine (see

level.

"Installation").

The laundry has not been The machine detected an Include both large and

spun properly and is still imbalance during the final small items in the load as

wet. spin and reduced the this will give better

spin speed automatically. distribution.

The laundry has not spun The spin speed selected Select a higher spin

satisfactorily. was too low. speed next time.

The pump makes strange This is not a fault! These noises occur at the end of a

noises.

pump sequence as a normal part of the operation.

There is a lot of

The water pressure is too – Clean the water inlet

detergent residue in the low.

detergent drawer.

filter.

– Select Water plus.

Powder detergent used

Add washing powder

with water softeners can and then add the water

be sticky.

softener.

Fabric conditioner is not The siphon tube is not

Clean the siphon, (see

completely dispensed or correctly positioned or is "Cleaning and care -

too much water remains clogged up.

Cleaning the detergent

dispenser drawer").

in the § compartment.

The display is in a

different language.

A different language has Set the language you

been selected in the want. The flag symbol

Programmable functions will guide you.

- Language J menu.

When laundry is dry, it

feels hard to the touch.

Too vigorous wash action. Programme in gentle

action and more water.

Not enough detergent

used.

Increase detergent dose

to prevent limescale

build-up in laundry.

No fabric conditioner

used

Use fabric conditioner in

last rinse.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

An unsatisfactory wash result

Problem

Possible cause

Remedy

Liquid detergent

does not give the

required result.

Liquid detergents

usually contain no

bleaching agents.

They do not remove

fruit, coffee and tea

stains.

– Use a general purpose

detergent containing a

bleaching agent.

– Pour stain removers into

compartment j of the

dispenser drawer and liquid

detergent into a dispenser ball.

– Never put stain removers and

liquid detergent together in the

dispenser drawer.

Grey, greasy

Insufficient amounts of – Use more detergent.

detergent were used

particles cling to

washed laundry.

– Before washing the next load

to break down the

run a Cottons 95°C programme

with powder detergent but

without a load.

particles of grease in

heavily soiled laundry.

A stale smell is in

the drum and on

laundry.

Low temperature

washing.

– Before washing the next load

run a Cottons 95°C programme

with powder detergent but

without a load.

White residues

which look like

powder detergent

are seen on dark

textiles after

The detergent

– Try and brush off the residues

with a soft brush once the

laundry is dry.

contained compounds

(zeolites) to aid water

softening which are

not soluble in water.

They have ended up

on the laundry.

– Wash dark textiles using a

detergent which contains no

zeolites. Liquid detergents

usually contain no zeolites.

washing.

– Use the Dark garments

programme.

Clothes are coming Programme was

– Reduce quantity of clothes in

drum.

out creased.

overloaded.

The wrong

– Check care labels and the

programme chart.

programme was used.

– Use easy iron conditioners.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

The drum door does not open when you press the Door button

Possible cause

Remedy

The machine is not

connected to the

Insert the plug in the socket and switch on and/or

switch the machine on with the I-On/0-Off button.

electricity supply and/or is

not switched on.

The safety lock has been

activated.

Deactivate the safety lock as described in

"Changing the programme sequence - Safety

lock".

Access via a code has

been activated.

Deactivate the code as described in

"Programmable functions - Code".

Power cut.

Open the drum door as described in the next

section.

The door was not correctly Press hard against the lock side of the drum door

engaged.

and then press the Door button.

There is still water in the

drum and the machine is

unable to drain.

Clean the drain filter and drain pump as described

in the next section.

For safety reasons the drum door cannot be opened if the suds temperature is

higher than 55°C.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

Opening the drum door in the

event of a blocked drain outlet

and/or power failure

Blocked drain outlet

If the drain outlet is blocked, up to

25 litres of water will be retained in the

machine.

^ Switch the washing machine off.

There is a lever behind the detergent

drawer fascia panel.

,^{Caution: if laundry has been}

washed at a high temperature, water

draining out of the machine will still

be hot. Danger of scalding!

Procedure for draining the machine

^ Place a suitable container under the

access flap.

When draining water from the

machine, do not unscrew the drain

filter completely or take it right out.

^ Remove the lever.

^ Unscrew the drain filter lid until water

runs out.

To interrupt the flow of water:

^ Use it to open the access flap.

^ Tighten the drain filter back up again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

Once the flow of water ceases:

,^{Make sure the drain filter is}

securely tightened. Otherwise there

is a risk of water leakage during use.

Opening the drum door

,^{Always make sure that the drum}

is stationary before reaching into the

machine to remove laundry.

Reaching into a moving drum is

extremely dangerous.

^ Remove the drain filter completely.

^ Clean it thoroughly.

^ Pull the emergency release

downwards (see illustration). The

drum door will open.

^ Remove any foreign objects (e.g.

buttons, coins, etc.) and fluff from the

filter housing. Turn the impeller by

hand to check that it rotates freely.

Any foreign object causing an

obstruction should be removed.

^ Put the drain filter back in place and

secure.

Download from Www.Somanuals.com. All Manuals Search And Download.

After sales service

In the event of any faults which you

cannot remedy yourself, please

contact:

Future updates (PC)

The indicator light marked PC is the

interface used by Miele service

technicians during servicing work for

testing purposes and for updating the

machine's programme data.

– your Miele Dealer or

– the Miele Customer Contact Centre

(see back cover for contact details).

When contacting your Dealer or Miele,

please quote the model and serial

number of your machine, both of which

are shown on the data plate visible

above the porthole glass when the door

is open.

Appliance guarantee

Please see the guarantee card

supplied with your machine.

Optional accessories

Optional accessories for this washing

machine are available from your Miele

Dealer, the Miele Spare Parts

Department or via the internet at

www.miele-shop.com.

Please note that telephone calls may

be monitored and recorded for

training purposes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Front view

aInlet hose with "Waterproof" system

hDetergent dispenser drawer

bElectricity supply cable

iDrum door

c - f Flexible drain hose (with

detachable swivel elbow)

jAccess to drain filter, drain pump

and emergency release

gControl panel

kHandle recesses for moving the

machine

lFour height adjustable feet

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Rear view

aProtruding lid for holding when

moving the machine

eTransit bar covers

fRestraining clip for inlet hose and

drain hose

bElectricity supply cable

cInlet hose with "Waterproof" system

dDrain hose

gRestraining clips for transit bars

when removed

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Installation surface

Installing the washing machine

A concrete floor is the most suitable

installation surface for a washing

machine, being far less prone to

vibration during the spin cycle than

wooden floorboards or a carpeted

surface.

To manoeuvre the machine out of its

packing case to its installation site hold

it by the edge of the lid where it

protrudes to the rear of the washing

machine as well as by the handle

recesses at the front.

Please note the following points:

,^{Ensure that the machine feet and}

the floor are dry to prevent the

machine from slipping during the

spin cycle.

^ The machine must be level and

securely positioned.

^ To avoid vibrations during spinning,

the machine should not be installed

on soft floor coverings.

Removing the transit bars

If installing on a wooden joist floor:

^ We recommend a plywood base

(at least 59x52x3 cm). The base

should span several joists and be

bolted to the joists and not only to the

floorboards. Check for the presence

of pipes and cables.

If possible, install the machine in a

corner, as this is usually the most stable

part of the floor.

,^{If the machine is installed on a}

raised plinth, it has to be secured

against slippage during spinning

using retaining clips (available from

the Miele Spare Parts Dept).

^ To remove the left and right covers

1. Use a screwdriver to prise out the

cover as illustrated.

2. Pull the cover forwards to remove.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

^ Using the spanner supplied turn the

^ Turn the right-hand transit bar 90°,

left-hand transit bar 90°, then

then

^ withdraw the transit bar.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

,^{To avoid the risk of injury the}

holes for the transit bars must be

covered after the transit bars have

been removed.

^ Secure the transit bars to the back of

the washing machine. Make sure that

holes b are fitted over retainers a.

,^{The washing machine must not}

be moved without the transit bars in

place.

^ Fit the covers on to the two holes.

Then plug the holes as shown with

the caps.

Store the transit bars as shown or

keep them in a safe place for future

use. They must be re-fitted if the

machine is to be moved again

(e.g.when moving house).

Re-fitting the transit bars

Re-fitting is carried out by reversing the

procedure.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Levelling the machine

The machine must stand perfectly level

on all four feet to ensure safe and

proper operation.

Incorrect installation may increase

electricity and water consumption and

may cause the machine to move about.

Screwing out and adjusting the feet

The four adjustable screw feet are used

to level the machine. All four feet are

screwed in when the machine is

delivered.

^ Use a spirit level to check the

machine is standing level.

^ Hold foot 1 securely with a pipe

wrench. Turn counter nut 2 again

using the spanner supplied until it

sits firmly up against the housing.

,^{All four counternuts must be}

firmly up against the housing. Please

also check this for the feet which did

not need adjustment. Otherwise

there is the danger of the machine

moving about.

^ Using the spanner supplied turn

counter nut 2 in a clockwise

direction. Then turn counter nut 2

together with foot 1 to unscrew.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Washer and Dryer stack

The fitting of building under kits and

stacking kits must only be

undertaken by qualified and

competent persons, in accordance

with the instructions supplied with

the kit.

A Miele tumble dryer can be stacked

with the washing machine. A "WTV"

stacking kit* is necessary and can be

purchased from the Miele Spare Parts

Department or via the internet at

www.miele-shop.com.

Building under a continuous

worktop/in a kitchen run

Please note

If you wish to push your machine under

a worktop and there is space to do this

without removing the lid, the

conversion kit is not necessary.

Otherwise the conversion kit is

essential.

– A special building under conversion

kit* is required.

To ensure electrical safety, the

washing machine lid must be

replaced by the cover plate supplied

with the conversion kit.

– For installation under a work surface

900/910 mm from the floor, a raising

kit* is required.

– Connections for electricity, water and

drainage should be installed in such

a way that they remain accessible

when the machine is in place.

a Safety distance to wall:

at least 2 cm

b Height:

Stacking kit with pull-out shelf:

approx. 169 cm

Fitting instructions are supplied with the

conversion kit.

Stacking kit without pull-out shelf:

approx. 170 cm

All parts marked* are available from

your Dealer or the Miele Spare Parts

Department.

Replacing the lid

If the lid has been removed in order to

fit a stacking kit or cover plate, ensure

that, if the lid is replaced, it fits securely

into the rear holders. Otherwise, it is not

properly secure for transport.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

The Miele Waterproof system

2) Electronic unit and washing

machine housing

The Miele Waterproof system protects

the washing machine from water

damage.

– Sump

Any leaking water is collected in a

sump in the base of the machine. A

float switches off the safety valves,

preventing any more water from

flowing into the machine and water in

the suds container is pumped away.

The system consists of three main

components:

1) the inlet hose

2) the electronic unit and the washing

machine housing

– Overflow protection

3) the drain hose

This prevents the washing machine

taking in too much water. If the water

level exceeds a certain level, the

drain pump switches in and pumps

the excess water away.

1) Inlet hose

– The inlet hose is fitted with an

additional electrical safety valve

which works like an automatic

stopcock and is housed in the inlet

hose connection box.

3) Drain hose

The drain hose is protected by a

ventilation system which prevents the

washing machine from being

emptied completely.

– It is pressure tested to between

7,000 and 10,000 kPa.

– The inlet hose has a protective

sleeve.

Any leaking water from the inlet hose

is fed into the sump through this

protective sleeve. A float switches off

the safety valve, preventing any

more water from flowing into the

machine and water in the suds

container is pumped away.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Connection to the water supply The machine should be connected to

the mains water supply in accordance

,^{The plastic casing of the safety}

valve contains electrical

with local and national safety

regulations. The German authorities do

not require it to have a non-return valve

as the washing machine has been

designed to comply with DIN

regulations.

components. The Waterproof system

must only be connected to its own

stopcock. It must not be connected

to mixer taps or similar and must not

be fitted in areas where there is the

risk of water or other liquids

reaching it.

The machine is designed to operate

with a flow pressure of between 100

and 1,000 kPa (1-10 bar). If it is higher

than 1,000 kPa it is essential to fit a

pressure reducing valve.

Connection to the mains water supply

should incorporate a mains stopcock

with ³/₄" thread. The stopcock should

be fitted by a qualified plumber.

,The connection point is subject

to mains water pressure. Turn on the

stopcock slowly and check for leaks.

Correct the position of the washer

and union if appropriate.

Do not get wet.

The washing machine is not suitable

for connection to a hot water supply

and connection to a household

water softener is not recommended.

The protective sleeve of the hose

must not be damaged or kinked.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Maintenance and care

If you intend to unscrew the Miele

Waterproof system hose from the

stopcock it is essential to disconnect

the machine from the electricity supply

first.

Only use a Miele Waterproof system

hose should you need a replacement.

In order to protect the water inlet

valve, the dirt filter in the water inlet

valve connection must not be

removed.

Extension hose

A 1.5 metre long (metal) extension hose

is available from your Miele dealer or

the Miele Spare Parts Department as an

optional extra.

This hose is tested to withstand

pressures of up to 14,000 kPa and can

be used as a flexible extension to the

water supply.

N.B. Using this hose renders the

Waterproof system safety valve on the

inlet hose ineffective.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Connection to the drainage

system

Please note:

The machine drains via a drain pump

with a delivery head of 1 metre*. The

drain hose must not be kinked as this

restricts drainage. The swivel elbow at

the end of the hose can be turned in

either direction, or can be detached if

required, with a sharp twist and pull.

If required, the drain hose can be

extended to a length of 5 m. The

necessary parts can purchased from

the Miele Spare Parts Department or

your Miele dealer.

aAdapter

* For a delivery head of more than 1 m

(up to a max. of 1.8 m) a second

bNut

cHose clip

dEnd of the hose

duo-drain pump is available with the

corresponding kit from the Miele Spare

Parts Department or your Miele Dealer.

^ Fit adapter a to the sink drain outlet

using nut b.

Drain hose connection:

1. Direct into a sink or basin:

Please note the following:

^ Attach the end of the hose d to

adapter a.

^ Use a screwdriver to tighten hose

– Hook the hose over the edge and

secure.

clip c up close to the nut.

– Make sure that the water can drain

away freely without hindrance.

Otherwise there is a risk of water

overflowing or of some of the drained

water being sucked back into the

machine.

2. Connected securely to a plastic

drain pipe with a rubber nipple.

There is no need to use a non-return

valve.

3. Connected securely to a standpipe.

4. Connected securely to a floor gully.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and connection

Electrical connection U.K.

Non-rewireable plugs BS 1363

All electrical work should be carried out The fuse cover must be refitted when

by a suitably qualified and competent

person, in strict accordance with

current national and local safety

regulations (BS 7671 in the UK).

changing the fuse, and if the fuse cover

is lost, the plug must not be used until a

suitable replacement is obtained. The

colour of the correct replacement cover

is that of the coloured insert in the base

of the plug, or the colour that is

Ensure power is not supplied to the

appliance until after installation work

has been carried out.

embossed in words on the base of the

plug (as applicable to the design of

plug fitted).

The appliance is supplied with a mains

cable with moulded plug ready for

connection to a 230-240V mains

supply.

Replacement fuses should be ASTA

approved to BS 1362 and have the

correct rating. Replacement fuses and

fuse covers may be purchased from

your local electrical supplier.

Please ensure the connection data

quoted on the data plate match the

household mains supply.

WARNING: THIS APPLIANCE

MUST BE EARTHED

Connection should be made via a

suitable switched socket which is easily

accessible after installation.

For extra safety it is advisable to install

a suitable residual current device

(RCD). Contact a qualified electrician

for advice.

Do not connect via an extension lead.

Extension leads do not guarantee the

required safety of the appliance (e.g.

danger of overheating).

Download from Www.Somanuals.com. All Manuals Search And Download.

Consumption data

Load

Consumption data

Energy

in kWh

1.99

Water

Duration

in litres

Short

Normal

Cottons

95°C

6.0 kg

3.0 kg

6.0 kg

3.0 kg

2.0 kg

1.0 kg

3.0 kg

3.5 kg

2.0 kg

3.0 kg

2.0 kg

3.0 kg

2 h 09 min

1 h 49 min

60°C

1.02

0.73

1 h 02 min

40°C

0.65

2 h 04 min

0.36

59 min

Minimum iron

Delicates

Woollens /

Silks /

0.50

59 min

1 h 19 min

59 min

30°C

40°C

60°C

40°C

0.35

49 min

0.23

–

39 min

0.25

–

36 min

Express

0.30

–

30 min

Automatic

Shirts

0.35 - 0.50

1.00

40 - 55

–

1 h 18 min

1 h 12 min

1 h 00 min

1 h 03 min

1 h 15 min

1 h 02 min

50 min

53 min

1 h 05 min

Denim

0.50

Outerwear

Dark garments

0.45

0.60

Notes for test institutes:

EN 60456 test programme

Short programme for test institutes; the Short extra option must be selected.

Consumption data can vary from the nominal values given depending on water

pressure, water hardness, water inlet temperature, room temperature, type and

volume of load, fluctuations in the electricity supply and any extra options

selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical data

Height

850 mm

Width

595 mm

Depth

580 mm

Depth with door open

Weight

975 mm

94 kg

Maximum floor load

Capacity

1600 Newton (approx. 160 kg)

6 kg dry laundry

see data plate

see data plate / plug

see "Consumption data"

100 kPa (1 bar)

1000 kPa (10 bar)

1.60 m

Voltage

Connected load

Fuse rating

Consumption data

Water flow pressure minimum

Water flow pressure maximum

Inlet hose length

Drain hose length

Mains connection cable length

Delivery head max.

Maximum drainage length

Test certificates awarded

1.50 m

1.60 m

1.00 m

5.00 m

see data plate

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions

for changing default settings

The programmable functions are used to alter the machine's electronics to suit

changing requirements.

Programmable functions can be altered at any time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions

To access programmable functions

To alter a programmable function

You can see the different options

available for a programmable function

by turning the programme selector.

The programmable functions are

accessed via the Start/Stop button

and the programme selector.

The option which is currently set will

Before you begin, first ensure that:

– The washing machine is switched off.

– The machine is properly closed.

have a tick L beside it.

FTurn the programme selector until

the option you want appears in the

display.

APress the Start/Stop button and keep

it pressed in whilst carrying out steps

B-C.

GPress the Start/Stop button to

activate this option.

BPress the I-On/0-Off button in.

To come out of programmable

functions

CAs soon as . . .

HTurn the programme selector until

Back A appears in the display.

Language !...

. . . appears in the display, release

IPress the Start/Stop button.

the Start/Stop button.

Language F

To select a programmable function

DTurn the programme selector until

the programmable function you

require appears in the display.

The display can be set to appear in

one of several different languages.

The flag J after the word Language

acts as a guide to prevent a language

which will not be understood from

being set.

EPress the Start/Stop button to confirm

your selection.

The language selected is saved to

memory.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions

Water plus

Gentle action

This programmable function is used

to select the water intake setting for

the Water plus extra option.

Activating gentle action reduces the

drum action and is suitable for

washing slightly soiled items more

gently. It should be activated for

garments with a single bar under the

care label and for articles which feel

too hard after they have been dried.

There are three different options:

Water +

(the machine is delivered with this

option selected)

Gentle action can be activated for the

Cottons and the Minimum iron

programmes.

The water level is increased in the wash

and rinse stages.

The washing machine is delivered with

the Gentle action setting deactivated.

Extra rinse

An extra rinse is introduced.

Suds cooling

Water+ & Extra rinse

When this is activated, additional

water flows into the drum at the end

of the main wash to cool the suds

down. Hot suds can damage plastic

drainage pipes.

The water intake is increased in the

wash and rinse stages and an

additional rinse is also introduced.

Suds cooling takes place when

temperatures of 95°C and 75°C are

selected.

Suds cooling should be activated:

– to prevent the danger of scalding if

the drain hose is hooked over the

edge of a sink or basin.

– where the drainage pipes do not

comply with DIN 1986.

The machine is delivered with Suds

cooling deactivated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions

Code

A code can be used to lock the

electronics on the washing machine

to prevent it being used without your

knowledge.

^ Press the Start/Stop button.

The following will appear in the display:

Code activated

When the code has been activated, you

have to enter a code after switching the

washing machine on. Otherwise the

washing machine cannot be operated.

Once the machine is switched off, it

can only be used again if the code is

entered.

Code ...

To use the washing machine when

the code is activated

^ Press the Start/Stop button.

When the machine is switched on

To activate the code

again, the display will request the code.

Activate

^ Enter code 125 as described above

and confirm the entry.

^ Press the Start/Stop button.

The washing machine is now unlocked

and ready for use.

The display will now request that a

code is entered.

To deactivate the code

To enter the code

Make sure the washing machine is

switched off and the door is properly

closed. Press the Start/Stop button and

keep it pressed in whilst you press the

l-On/0-Off button in.

The code is 125 and cannot be altered.

__ __

^ Turn the programme selector until the

first number appears in the display.

As soon as . . .

^ Confirm your selection of the number

__ __

by pressing the Start/Stop button.

^ Repeat the process until all three

. . . appears in the display, release

numbers have been entered.

the Start/Stop button.

^ Now enter the code and press the

Start/Stop button.

^ Select Code and confirm Deactivate.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions

Temperature unit

Keypad tone

You can chose for the temperature to

be displayed as °C/Celsius or

°F/Fahrenheit.

An audible tone sounds each time a

button is pressed.

The machine is delivered with the

keypad tone deactivated.

The machine is delivered with

°C/Celsius as the default setting.

Brightness

Buzzer

There are ten different display

brightness settings.

When the buzzer function has been

activated, an audible tone sounds at

the end of a programme or when

Rinse hold is reached.

The bar chart shows you the setting.

The machine is delivered with the

display brightness on setting 5.

There are two volumes:

This will change as soon as a different

setting is chosen.

Normal

(the machine is delivered with this

option as the default setting.)

Contrast

The buzzer sounds at the end of a

programme or when Rinse hold is

reached.

There are ten different display

contrast settings.

The bar chart shows you the setting.

Loud

The machine is delivered with the

display contrast on setting 5.

The buzzer sounds at maximum volume

Loud at the end of a programme or

when Rinse hold is reached.

This will change as soon as a different

setting is chosen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions

Standby display

Memory

To save energy, the display goes out

and the indicator light for the Start/

Stop button will start flashing slowly.

The washing machine will store the

most recently selected settings

(programme, temperature, spin

speed and any extra options) in

memory once the programme has

started.

The display will always go out,

– if a programme is not selected within

10 minutes of the machine being

switched on.

These settings will appear in the

display the next time the machine is

switched on.

– 10 minutes after the end of a

programme.

The machine is delivered with the

memory function deactivated.

Pressing one of the buttons switches

the display back on again.

Anti-crease

You can also choose whether you want

the display to go out 10 minutes after a

programme has started or to remain

visible throughout the programme.

Anti-crease helps prevent creasing if

laundry is not normally removed

immediately after the end of a

programme.

The drum will turn at intervals for up to

30 minutes after the programme has

finished.

The standby function is switched on.

When this option is selected, the

display will go out 10 minutes after a

programme has started.

The door can be opened and laundry

removed at any time during the

anti-crease phase.

Not in current prog.

(the machine is delivered with this

option selected)

(the machine is delivered with this

option selected)

The standby function is switched off.

The display will remain visible during a

programme.

Anti-crease is activated.

Off

Anti-crease is deactivated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alteration rights reserved/1208/W 3824 WPS

M.-Nr. 07 171 200 / 01

Download from Www.Somanuals.com. All Manuals Search And Download.

Multiquip Portable Generator GA 36RZ2 User Manual
National Instruments Power Supply NI PXI 1006 User Manual
NEC TV Cables E323 User Manual
NETGEAR Switch DS104 User Manual
Nikon Binoculars 10x44 SF IL User Manual
Nordyne Heat Pump T3BN User Manual
Omega Vehicle Security Electric Heater SEPHB Series User Manual
Palsonic Flat Panel Television PDP4220HD User Manual
Panasonic DVD Player DVD S42 User Manual
Panasonic Fax Machine KX PW506DL User Manual