Miele Refrigerator K 1801 Vi User Manual

Operating and Installation  
Instructions  
Refrigerator  
K 1801 Vi, K 1811 Vi  
K 1901 Vi, K 1911 Vi  
en - US, CA  
To prevent accidents  
and appliance damage  
read these instructions  
before  
installation or use.  
M.-Nr. 09 169 670  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caring for the environment  
Disposal of packing materials  
Disposal of an old appliance  
The cardboard box and packing  
materials are biodegradable and  
recyclable. Please recycle.  
Old appliances contain materials that  
can be recycled. Please contact your  
local recycling center about the  
possibility of recycling these materials.  
Ensure that any plastic wrappings,  
bags, etc., are disposed of safely and  
kept out of the reach of babies and  
young children. Danger of suffocation!  
Before discarding an old appliance,  
disconnect it from the electrical supply  
and cut off the power cord to prevent it  
from becoming a hazard.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Installation site  
Have the appliance installed by a  
qualified technician, according to  
the enclosed installation instructions.  
The appliance should be installed in a  
dry, well ventilated room.  
Do not install the appliance:  
- outdoors,  
WARNING  
- in an environment with dripping  
water,  
This appliance is top-heavy and  
must be secured to prevent it from  
tipping forward.  
- in rooms which are at risk of frost.  
Keep the door closed until the  
appliance is completely installed  
and secured as per the installation  
instructions.  
The installation location should not be  
exposed to direct sunlight, nor near a  
heat source, such as an oven,  
radiator, etc.  
The ambient temperature should not  
drop below 55°F (13°C) or rise above  
110°F (43°C), otherwise malfunctions  
Empty weight of your machine:  
K 18x1 Vi . . . . . . . . . . 419 lbs (189 kg)  
K 19x1 Vi . . . . . . . . . . 452 lbs (205 kg) may occur.  
If installation next to a heat source is  
unavoidable observe the following  
minimum distances from the heat  
source:  
– 1 1/4" (3 cm) from an electric cooktop  
or electric oven.  
– 12" (30 cm) from a gas or oil  
cooktop, range or oven.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Base  
Ventilation  
A fully loaded appliance is very heavy.  
The load-bearing capacity of your floor  
must meet the following requirements:  
The air intake and outlet must not be  
blocked or covered in any way. They  
also need to be dusted/cleaned on a  
regular basis.  
K 18x1 Vi . . . . . . . . . . 996 lbs (452 kg)  
K 19x1 Vi . . . . . . . . . 1,191 lbs (540 kg)  
Installation niche  
To ensure that the appliance is installed  
securely and functions properly, the  
base must be flat, level and made of a  
hard, rigid material.  
To ensure safe, trouble-free installation  
and the best possible cosmetic result,  
check to be sure that the installation  
space complies with the installation  
dimensions. See "Niche dimensions".  
If in doubt, contact Miele.  
The side walls of the installation cavity  
must be plumb.  
Furniture/fixtures  
The minimum thickness of the side  
walls and the top wall must be 5/8"  
(16 mm).  
The new appliance will be mounted  
securely to adjacent and overhead  
furniture/fixtures.  
For this reason it is essential that all  
attachable furniture/fixtures are  
connected securely to the base or the  
wall by suitable means.  
The minimum thickness of the toe-kick  
panel must be ½" (13 mm). A thickness  
of 3/4" (19 mm) is recommended.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Stainless steel panels  
Side-by-side  
Stainless steel door panels and toe-kick This appliance can be installed  
covers are available from Miele.  
"side-by-side" with another  
fridge/freezer using a "Merging Kit".  
Custom door panels  
The "Merging Kit" is available from  
Miele.  
This appliance is compatible with all  
styles and designs of kitchen cabinetry.  
Contact Miele or your dealer for  
specific information about which  
combinations will work with your  
appliance.  
The total weight of the decorative  
panel(s) must not exceed the following:  
K 18x1 Vi. . . . . . . . . . . . 110 lbs (50 kg)  
K 19x1 Vi. . . . . . . . . . . . . 81 lbs (37 kg)  
For instructions on how to attach the  
appliances and install the heating  
mat, please refer to the instructions  
included with the "Merging Kit",  
available from Miele.  
Installation options  
There are many different installation  
options. These are limited only by the  
design of the kitchen.  
Installation without a partition using  
the "Merging Kit"  
The door hinge cannot be  
exchanged.  
Single column  
The appliance can be installed at any  
preferred location in the kitchen.  
However, be sure the door will open  
and close properly in the chosen  
location.  
If the appliances are installed directly  
next to each other (without a partition),  
they need to be attached together  
using the "Merging Kit".  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Installation with partition using the  
"Merging Kit"  
Side panels  
If one side of the appliance is visible, a  
side panel must be used.  
The minimum thickness of the partition  
is 5/8" (16 mm).  
The side panel must be firmly secured  
to the wall, the floor and the overhead  
furniture/fixtures before the appliance is  
placed in the cavity.  
The dimensions of the side panel are  
taken from the opposite wall of the  
installation space. During installation,  
ensure that the cavity is square and the  
measurements are correct.  
If there is a partition with a thickness  
from 5/8" (16 mm) to 6 5/16" (160 mm)  
between the adjacent appliances, then  
each appliance should be individually  
installed within its own niche using the  
mounting accessories included.  
The "Merging Kit" will also be needed.  
The "Merging Kit" is available from  
Miele.  
Installation with partition without  
using the "Merging Kit"  
If there is a partition with a thickness of  
more than 6 5/16" (160 mm) between  
the adjacent appliances, then each  
appliance should be individually  
installed within its own niche using the  
mounting accessories included (the  
"Merging Kit" is not necessary).  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Adjusting the door opening  
angle (optional accessory)  
Front panel gap kit (optional  
accessory)  
Depending on the installation site, it  
may be necessary to adjust the door  
opening angle to 90°.  
^ Open the door.  
Two adjacent furniture doors can be  
attached instead of one large door.  
To connect these furniture doors on the  
rear, a metal strip can be purchased as  
an optional accessory. Contact Miele.  
^ Insert the banking pin through the  
holes and drive in with a hammer.  
The door opening angle is now limited  
to 90°.  
When attaching the metal strip to the  
furniture doors, observe the maximum  
length of the screws and the position of  
the drill holes.  
Always screw into the best possible  
load-bearing material of the custom  
doors.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Door dimensions (open min. 90°)  
*The dimensions of the door fronts and  
handles will vary according to each  
individual kitchen.  
3/8" (10 mm)  
A
B
C
K 18X1 Vi 32 5/8" (829 mm)  
Door front max. 1 1/2" (38 mm) Door handle*  
K 19X1 Vi 38 11/16" (982 mm) Door front max. 1 1/2" (38 mm) Door handle*  
Door dimensions (open min. 115°C)  
*The dimensions of the door fronts and  
handles will vary according to each  
individual kitchen.  
A
B
C
D
K 18X1 Vi 32 5/8" (829 mm) Door front max.  
Door handle* 14 5/16"  
(363 mm)  
1 1/2" (38 mm)  
K 19X1 Vi 38 11/16" (982 mm) Door front max.  
Door handle* 16 7/8"  
(428 mm)  
1 1/2" (38 mm)  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Niche dimensions  
Niche width (A)  
K 18X1 Vi  
K 19X1 Vi  
30" (762 mm)  
36" (915 mm)  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Power supply  
1. Power supply  
A
K 18X1 Vi  
K 19X1 Vi  
15" (381 mm)  
18" (458 mm)  
Door front dimensions  
A
B
K 18X1 Vi 79 1/8"  
29 3/4"  
(2029 mm) (756 mm)  
K 19X1 Vi 79 1/8"  
35 3/4"  
(2029 mm) (908 mm)  
4" - 5 3/16" (102 - 132 mm)  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Before you begin  
– Level  
– Tape measure  
– Square  
Read these instructions completely  
and carefully.  
Have the appliance installed by a  
qualified technician, according to  
the enclosed installation instructions.  
When fastening the cabinet to the wall  
behind it (see "Installing the appliance")  
use:  
– suitable plugs/screws depending on  
the type of wall.  
To reduce the risk of injury or  
damage to the product, two people  
should be used for installation.  
– several mounting brackets, if required.  
Other  
These installation instructions are  
intended for use by qualified installers.  
In addition to these instructions, the  
appliance must be installed in  
accordance with all local codes. In the  
absence of a local code, the following  
should be used:  
– Stepladder  
– Dolly, hand truck  
– Wooden beam  
(cross section min. 3" x 4"  
[75 mm x 100 mm] as an alternative  
tilt protection, length depends on the  
width of the installation cavity)  
– In the USA, the National Electric  
Code, ANSI/NFPA 70 - latest  
edition/State and Municipal codes  
and/or local codes.  
– Wood screws in different sizes  
Optional accessories  
– In Canada, the Canadian Electric  
code C22.1 - latest edition/Provincial  
and Municipal codes and/or local  
codes.  
– "Merging Kit" for side-by-side installation  
– Front panel gap kit  
– RemoteVision module for wireless  
monitoring  
Tools needed for installation  
– Cordless screwdriver  
– Torx screwdriver  
– Hammer drill  
– Wood drills in different sizes  
– Hammer  
– rachet 5/16" (8 mm)  
– Adhesive tape  
– Multi-grip pliers  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Aligning the housing unit  
Check the installation niche  
To ensure a safe, trouble-free  
installation and the best possible  
cosmetic result, check to be sure  
that the installation space complies  
with the installation requirements.  
^ Check the base (see "Installation").  
^ Check the dimensions of the cavity.  
^ Check that the cavity is square.  
^ Check the location of the power  
outlet.  
^ Check that all furniture parts in the  
vicinity of the appliance are securely  
connected to the wall.  
The housing unit must be carefully  
aligned using a spirit level before  
installing the appliance. The unit  
corners must be at right angles, as  
otherwise the furniture door will not  
align correctly with the 4 corners of the  
appliance.  
^ Check that the adjacent  
furniture/fixtures do not collide with  
the open door.  
Before installation  
,Caution - the appliance is very  
heavy. Use caution when unpacking  
and opening the door, danger of  
tipping.  
– The side panels of the housing must  
be even.  
– The housing unit panels must be at  
least 5/8" (16 mm) thick.  
^ To protect the base from damage  
during installation, attach a hard  
board, linoleum, etc., to the floor in  
front of the intended installation  
location.  
– The plinth facing must be at least  
1/2" (13 mm) thick, preferably 3/4"  
19 mm).  
^ Remove any cable clips from the  
back of the appliance.  
^ Take the supplied accessories out of  
the protective packaging.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
^ From the rear of the appliance  
carefully lift it from the pallet.  
Once the appliance is on the ground it  
can be wheeled around.  
RemoteVision module  
installation  
(optional accessory)  
^ Do not remove the installation  
supports from the appliance door.  
They will be used later in the  
installation niche.  
Always disconnect the appliance  
from the power supply when  
performing installation, maintenance  
or service work.  
There are transportation safety  
devices inside the appliance to  
protect the shelves and storage  
compartments until installation is  
complete. Do not remove them, or  
parts may be damaged.  
Install the RemoteVision module  
before placing the appliance in its  
installation niche.  
Once connected the RemoteVision  
module will increase the energy  
consumption of the appliance.  
^ Check the appliance for damage in  
The slot for the RemoteVision module is  
located in the lower area of the back of  
your appliance.  
transit.  
Do not install the appliance if it is  
visibly damaged. If in doubt, contact  
your dealer.  
^ Unscrew the screws a on the cover  
b and pull off the sticker c.  
^ Loosen the bracket that holds the  
appliance to the pallet.  
^ Remove the cover b.  
,Caution! The appliance is no  
longer secured and may be unstable.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
^ Push the module into the slot until it  
locks into place.  
^ Pull the antenna d straight out.  
^ Connect the appliance to the power  
supply and turn it on. After several  
seconds the indicator light e will  
come on.  
^ Guide the cover b over the antenna  
d and screw on the cover.  
^ Angle the antenna d so that it faces  
to the right or left.  
The indicator light will display different  
colors one after the other; any control  
light at the end indicates that the  
module was correctly installed.  
^ If necessary, disconnect the power  
supply and continue installing the  
appliance.  
If the indicator light does not come on,  
installation of the module was  
Preparing the installation  
niche  
unsuccessful. In that case, repeat the  
process. If that does not correct the  
problem, contact Miele.  
,Keep the appliance door closed  
until it is securely fastened in the  
niche. Tipping hazard.  
Because of the size and weight of  
the appliance, it is essential to  
ensure that the appliance cannot tip  
over once it has been mounted in  
the niche.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Mounting Accessories  
The mounting accessories needed for  
installing the appliance into the niche  
are included in the packaging. Several  
plastic bags are included which are  
numbered alphabetically.  
The bag needed for each step will be  
marked with its respective letter.  
The distance "D" between the anti-tip  
brackets b is the width of the  
appliance.  
^ Use the included Torx screwdriver to  
tighten the screws.  
^ Position the anti-tip brackets b on  
the left and right walls of the  
appliance niche.  
Anti-tip brackets  
The anti-tip brackets help keep the  
appliance safely secured to the  
installation niche to prevent tipping.  
^ Mark the holes through the anti-tip  
brackets b on the floor of the  
installation niche.  
Two anti-tip brackets are  
recommended for each appliance or  
appliance combination (side-by-side).  
^ Set the brackets aside.  
Screws are supplied with the  
appliance for various  
applications/materials.  
If the anti-tip brackets cannot be  
attached securely with the screws  
supplied, an alternative anti-tip  
device can be used.  
If the installation niche is deeper than  
the appliance, a solid wooden beam a  
can be placed behind the anti-tip  
Assure that there are no electrical  
wires in the area which the screws  
could penetrate - risk of injury and  
damage.  
brackets b so the appliance can be  
securely attached to the base or wall.  
The length of the wooden beam a  
should be the width of the installation  
space.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
In a cabinet with a back wall  
^ Drill pilot holes:  
1/8" (3 mm) for the 5 x 60 mm wood  
screws  
1/16" (2 mm) for the 4 x 15 mm wood  
screws.  
^ screw the back wall of the cabinet in  
several places directly to the wall  
behind it.  
^ Tightly secure the anti-tip brackets in  
For this, use suitable plugs/screws  
depending on the type of wall.  
the niche.  
Be certain the screws penetrate  
through the flooring and into the wall  
plate a minimum of 3/4" (19 mm).  
In a cabinet without a back wall  
If the included anti-tip brackets cannot  
be secured in the niche, the built-in  
cabinet must be secured to the wall  
behind it with several screws. Only in  
this way can the appliance later  
secured in the built-in cabinet be  
prevented from tipping.  
screw the cabinet to the wall behind it  
in several places using suitable  
mounting brackets.  
For this, use suitable plugs/screws  
depending on the type of wall.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Securing an alternative anti-tip  
device  
– The beam must cover the appliance  
by at least 2" (50.8 mm).  
If the anti-tip brackets cannot be  
attached securely, an alternative  
anti-tip device can be used.  
^ Mark the installation height (lower  
edge of the beam) on the rear wall of  
the niche.  
Ensure that there is no "give" between  
the appliance and the anti-tip device.  
^ Select screws according to the  
thickness of the wooden beam.  
Example: 3 ½" (89 mm) screw for 2x4  
beam.  
If possible, always screw the  
wooden beam to existing studs.  
^ Determine the number of screws  
based on the cavity width, to ensure  
that the beam will be attached  
securely.  
^ Locate wall studs near the rear wall  
of the cavity and mark drill holes in  
the beam.  
^ Pre-drill the wooden beam.  
^ Attach the wooden beam to the rear  
wall of the niche.  
– Cut a wooden beam  
(cross section min. 3" x 4"  
[75 mm x 100 mm] to the required  
length).  
– The length is equal to the width of  
the installation niche.  
– If the installation niche is deeper than  
the appliance, select a beam with a  
larger cross section, or attach two  
beams.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Sliding the appliance into the  
installation space  
^ Plug the appliance into the power  
outlet b.  
The plug of the appliance should be  
easily accessible after installation.  
If the plug is not accessible after the  
appliance has been installed,  
disconnection from the power  
supply should be completed via the  
circuit breaker.  
If a side-by-side installation is  
desired, connect the two appliances  
together. See the Installation Manual  
included with the "Merging Kit".  
In the case of side-by-side  
installations, a separate outlet must  
be used for each appliance.  
^ To prevent the power cord from  
becoming caught:  
Tie a piece of string to the middle of  
the power cord and feed it forward  
under the appliance. When sliding  
the appliance in, pull the cable  
forward c.  
^ Unscrew the plinth.  
^ Carefully slide the appliance into the  
space until the height-adjustable  
wheels interlock with the anti-tip  
brackets d.  
If resistance is felt when attempting to  
slide the appliance into the installation  
niche - for example, because the floor  
is uneven,  
^ Turn the rear adjustable wheels  
slightly outward (see "Aligning the  
appliance"), then push the appliance  
in.  
Be careful not to damage the power  
cord attached to the floor.  
^ To protect the corners of the  
installation space, attach the  
supplied edge protector a on both  
sides with adhesive tape.  
^ Remove the edge protector a.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Aligning the appliance  
Important!  
^ Align the appliance with the custom  
When unscrewing the  
front.  
height-adjustable feet, proceed  
gradually, alternating between left  
and right.  
^ Unscrew the height-adjustable feet  
until the mark on the base has  
reached the indicated guide  
dimension 1 1/4" (32 mm). The guide  
dimension of 1 1/4" (32 mm) is  
related to a niche height of 84"  
(2134 mm).  
The installation aids e on the  
appliance door have been designed for  
custom door thicknesses of 3/4"  
(19 mm) and 1 1/2" (38 mm).  
The height-adjustable feet at the front  
and rear can all be adjusted from the  
front:  
– Front feet:  
Adjust with a rachet 5/16" (8 mm) f  
^ Align the custom door with a level.  
– Rear feet:  
Adjust with a (cordless) screwdriver  
and/or a rachet 5/16" (8 mm) for fine  
adjustment g  
Note:  
– When unscrewing the  
height-adjustable feet, proceed  
gradually, alternating between left  
and right.  
^ Use a level to align the installation  
aids e on the door.  
– If using a wooden beam as an  
alternative anti-tip device, rotate the  
appliance all the way toward the  
wooden beam.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Attaching the appliance to the  
installation niche  
^ Secure the attachment plate side lugs.  
If there is a fairly large gap above the  
appliance, cut a wooden beam to fit  
exactly and place it in the gap.  
^ Screw the attachment plate lugs h to  
the overhead furniture/fixtures.  
If there is no way to attach the top of  
the appliance, it can be attached to the  
sides of the installation niche.  
^ If necessary, shorten the filler strip j  
to the required height.  
^ Place the 2 strips on top of each  
other k.  
^ Insert the filler strip until you hear it  
click into place l.  
^ Pull out the plate side lugs i.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
For a side-by-side combination the filler ^ Open the appliance door.  
strips from both appliances are put  
together to form one long filler strip:  
^ Take the peg from the "side-by-side  
merging kit" and insert it halfway into  
the filler strip rail on the left-side  
appliance.  
^ Place the second filler strip on the  
peg and press both filler strips  
together.  
^ Screw the attachment plate lugs m to  
the adjacent furniture/fixtures.  
^ Insert both filler strips into the  
installation space above the  
With side-by-side combinations, only  
the external side of the appliances can  
be secured to the niche.  
appliance, until they click into place.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Preparing the custom door  
^ Open the appliance door.  
^ Unscrew the installation supports n  
from the appliance door.  
^ Measure the distance X between the  
bracket from the door and the  
overhead furniture/fixtures.  
^ Loosen the remaining screws from  
the strips o on each side of the door,  
then remove.  
^ Loosen the two nuts.  
Set aside the nuts - you will need  
them again later.  
^ Set aside the screws and side strips  
o - you will need them again later.  
^ With the inside facing up, lay the  
custom door on a stable surface (to  
avoid scratch marks, place some  
plastic or a cloth on the surface).  
^ Remove the light switch cover (see  
arrow).  
^ Close the appliance door.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
^ Mark the distance X on the back-side  
Please note: When attaching the  
mounting frame onto two adjacent  
doors (see "Front panel gap kit")  
screw into the thicker outer frames  
of the doors only.  
of the custom door.  
^ Also calculate and mark the center of  
the custom door Y.  
^ Remove the mounting frame from the  
appliance door and position it  
according to the markings on the  
custom door.  
The bracket includes a variety of holes  
for the various design options of  
custom doors.  
^ Pre-drill the holes.  
When performing work on the custom  
door, always observe the following:  
^ Tightly screw on the bracket using  
the pre-drilled holes:  
– Always select the best load-bearing  
surface of the custom door as the  
location for screws.  
Attach the bracket to each  
attachment point with at least one  
screw.  
– Always select a screw length that is  
shorter than the thickness of the door  
front.  
^ Secure the door handle to the front of  
the appliance from the inside.  
^ Attach the bracket at the top with at  
least 6 screws.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Attaching and aligning the  
custom door front  
^ Align the custom door height with the  
threaded bolts p.  
^ Now tighten the nuts q on top. This  
secures the appliance door.  
^ Open the door and hang the custom  
door with the mounting frame over  
the threaded bolts p.  
^ Put the side strips o back into place  
and screw them completely down on  
both sides of the appliance door.  
Bag E contains spare screws for this  
purpose.  
^ Screw the nuts q a few turns onto  
the threaded bolts p. Do not tighten  
the nuts completely.  
^ Close the appliance door and check  
the distance to doors of adjacent  
furniture/fixtures.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Attaching the fixing brackets  
Attaching the covers  
(Only for appliances using the "Front  
panel gap kit".)  
^ To mount the cover strips on both  
sides of the door, click them into  
place from bottom to top, into the  
gap between the appliance door and  
the custom door.  
The fixing brackets are used to secure  
the custom door front to the bottom of  
the appliance door.  
^ Open the appliance door all the way.  
^ Slightly loosen the screw (1.).  
^ Position the fixing bracket on the  
appliance door (2.) and pre-drill a  
hole in the custom door front.  
^ Screw the fixing bracket securely to  
the custom door front (3.).  
^ Tighten the screw (4.).  
^ Put the cover on the bracket (5.).  
The number of lower brackets will  
depend on the width and the design of  
the custom door.  
^ Screw the brackets onto both sides  
of the appliance, to hold the cover  
strip.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
Attaching the toe-kick cover  
The maximum height of the toe-kick  
cover is 4" (101 mm) from the top of  
the floor. Do not cover the ventilation  
slits in the plinth. Risk of damage to  
the appliance.  
^ If required, cut the toe-kick cover to  
the required length and height.  
^ Insert the cover strip into the space  
between the appliance and the  
wooden panel.  
For side-by-side combinations, the  
cover strips (on both sides of the  
appliance) are applied to the  
outermost spaces only.  
^ Attach the plinth to the appliance,  
and put the included cover plates in  
place.  
^ Attach the light switch cover.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the appliance  
^ Remove the foil from the adhesive  
strips.  
^ Attach the toe-kick cover to the  
plinth.  
^ Position the air separator in the  
Mounting the air separator  
center of the appliance door.  
The air separator keeps the supply and  
exhaust air separate. This prevents  
warm exhaust air from flowing into the  
machine, optimizing the energy  
performance of the unit.  
^ From below, screw the air separator  
firmly onto the door with the 2  
screws.  
^ If necessary, shorten the three parts  
of the air separator.  
^ Insert the foam pieces back into the  
sides.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical connection  
The appliance is supplied with a  
UL-listed, 3-wire power cord and  
NEMA 5-15 P plug ready for connection  
to a 120 V, 60 Hz supply.  
, Avoid the risk of electrical  
shock  
- Plug into a grounded 3-prong  
outlet.  
The fuse rating is 15 amps.  
- Do not move the ground plug.  
- Do not use an adapter.  
- Do not use an extension cord.  
The appliance requires a 3-wire  
receptacle.  
The receptacle must be installed by a  
licensed electrician only.  
Failure to follow these instructions  
can result in death, fire, or electrical  
shock.  
In the case of side-by-side installations,  
a separate outlet must be used for each  
appliance. Ideally, the power outlet  
should be next to the appliance and  
easily accessible. Do not connect the  
appliance to the power supply by an  
extension cord. Extension cords do not  
guarantee the required safety of the  
appliance (danger of overheating).  
Improper connection of the  
equipment grounding conductor  
may result in electric shock. If you  
are in any doubt as to whether the  
appliance has been properly  
grounded, have the appliance  
checked by a qualified electrician or  
service technician.  
If any changes are needed to the  
household wiring or power supply, this  
work must be performed by a qualified  
electrician.  
Installation, repairs and other work  
by unqualified persons could be  
dangerous.  
Before installing the appliance,  
verify that the voltage, load and  
circuit rating information found on  
the data plate match the household  
electrical supply.  
If there are any questions regarding the  
electrical connection of this appliance  
to the power supply, please consult a  
licensed electrician or call the Miele  
Technical Service.  
U1-800-999-1360  
V1-800-565-6435  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alteration rights reserved / 4911  
M.-Nr. 09 169 670 / 03  
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST  
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Convection Oven H 333 User Manual
Milwaukee Grinder 5211 User Manual
Multiquip Refrigerator HHSD5 User Manual
National Instruments Switch PC DIO 96 User Manual
NEC Computer Hardware PD17062 User Manual
Niles Audio Speaker RS6 Granite User Manual
Nokia Cell Phone RAE 3N User Manual
Olympus Camcorder E 30 User Manual
Palsonic DVD Recorder DVD R 212 User Manual
Parkside Grinder PWS 230 A1 User Manual