Miele Refrigerator F 1411 Vi User Manual

Operating and Installation

Instructions

Freezer

with Ice Maker

F 1411 Vi

en - US, CA

To prevent accidents

and appliance damage

read these instructions

before

installation or use.

M.-Nr. 09 743 780

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Stainless steel panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Custom door panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

RemoteVision module installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Preparing the installation niche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Sliding the appliance into the niche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Aligning the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Attaching the appliance to the installation niche. . . . . . . . . . . . . . . . . . . . . . . . . . 62

Preparing the custom door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Attaching and aligning the custom door front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

RemoteVision (optional accessory) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

When using the appliance, follow

basic safety precautions, including

the following:

Electrical Safety

Before installation, make sure that

the voltage and frequency listed on the

data plate correspond with the

Read all instructions before

installation and use to prevent

accidents and machine damage.

household electrical supply. This data

must correspond to prevent injury and

machine damage. Consult a qualified

electrician if in doubt.

Before installation or service,

This appliance is intended for

disconnect the power supply to the

work area by unplugging the unit,

"tripping" the circuit breaker or

removing the fuse.

residential use only. Use only as

described in this Operating manual.

Only use the appliance for its

intended purpose.

Do not use an extension cord to

connect this appliance to electricity.

Extension cords do not guarantee the

required safety of the appliance

(e.g., danger of overheating).

This appliance complies with current

safety requirements. Improper use

of the appliance can lead to

personal injury and material

damage.

Be certain your appliance is

properly installed and grounded by a

qualified technician. To guarantee the

electrical safety of this appliance

continuity must exist between the

appliance and an effective grounding

system. It is imperative that this basic

safety requirement be met. If there is

any doubt, have the electrical system of

the house checked by a qualified

electrician.

Keep these operating instructions in

a safe place and pass them on to

any future user.

Only connect power to the

appliance when all installation and

plumbing work is complete.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Installation

In appliances with an automatic ice

maker, avoid contact with the moving

This appliance is top-heavy and

must be secured to prevent the

possibility of tipping forward.

Keep the door closed until the

appliance is completely installed

and secured per installation

instructions.

parts of the ejector mechanism, or with

the heating element located on the

bottom of the ice maker. Do not place

fingers or hands on the automatic ice

making mechanism while the freezer is

plugged in.

The ice cube maker is not suitable

for connection to a hot water supply.

This appliance must be installed

and connected in compliance with the

Do not use water that is

installation instructions.

microbiologically or chemically unsafe

or of unknown quality without adequate

disinfection or other treatment before or

after the filter is used; the filter alone is

not an adequate safeguard.

Installation and repair work should

be performed by a Miele authorized

service technician. Work by unqualified

persons could be dangerous and may

void the warranty.

Use

Installation must comply with local

plumbing regulations and state laws.

This appliance is not designed for

commercial use. It is intended for use in

domestic households and in similar

working and residential environments

such as:

Do not operate any appliance with a

damaged cord or plug, or if the

appliance has been damaged in any

manner. Contact Miele’s Technical Ser-

vice Department.

– shops, offices and similar work

environments

This appliance must not be used in

a non-stationary location (e.g. on a

– by customers in hotels, motels, Bed

& Breakfasts or similar residential

environments.

ship).

Do not install the freezer in a room

This appliance is not intended for

outdoor use.

with too low an ambient temperature,

e.g., a garage, as this may lead to the

appliance switching off for longer

periods so that it cannot maintain the

required temperature.

The appliance is only intended for

residential use to store frozen foods,

freeze fresh foods and prepare ice.

All other uses are prohibited and may

be dangerous.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Persons who lack physical, sensory

Do not use defrosting sprays or

de-icers, as they might contain

or mental abilities, or experience with

the machine should not use it without

supervision or instruction by a

responsible person.

substances which could damage the

plastic parts or which could cause a

build-up of gases and pose a danger to

health.

To reduce the risk of injury, do not

allow children to play in, on or near the

appliance, especially in the door hinge

area.

Do not use any oils or grease on the

door seal, as these will cause the seal

to deteriorate and become porous with

time.

After your freezer is in operation, do

not touch the cold surfaces in the

Do not block the ventilation gaps in

freezer compartment, particularly when the plinth or the top of the appliance

hands are damp or wet. Skin may

adhere to these extremely cold

surfaces.

housing unit, as this can impair the

efficiency of the appliance, increase the

electricity consumption and cause

damage to the appliance.

Do not refreeze frozen foods which

have thawed completely.

Never use a steam cleaner to clean

the appliance. Pressurized steam could

damage electrical components and

cause a short circuit.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

Do not deactivate the water filter

display.

Do not use sharp-edged objects to

remove frost and ice, or separate

frozen foods and remove ice trays.

They will damage the evaporator,

causing irreversible damage to the

appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Disposal of your old appliance

Before disposing of an old

appliance, first make the door latch or

lock unusable.

Take off the door.

Leave the shelves in place so that

children may not easily climb inside.

Consult with your municipal policy

on recycling.

Be careful not to damage any part of

the pipework while awaiting disposal

by:

puncturing the refrigerant

channels in the evaporator.

bending any pipework.

scratching the surface coating.

Splashes of refrigerant can damage the

eyes.

Your old freezer may have a cooling

system that used CFCs

(chlorofluorocarbons). CFCs are believed

to harm stratospheric ozone.

If you intentionally release this CFC

refrigerant, you can be subject to fines

and imprisonment under provisions of

environmental legislation. Make sure the

CFC refrigerant is removed and disposed

of by a qualified technician.

SAVE THESE

INSTRUCTIONS

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the freezer

aDoor shelves (height adjustable)

bShelves (height adjustable)

cIce cube maker

dIce cube container

eControl panel

fMain switch to turn the appliance

On/Off

gFreezer baskets

hWater filter

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the freezer

Control panel

aAccess button "p"

dOn/Off sensor button for the ice cube

maker

bTemperature display

X colder; Y warmer

eSensor button for the temperature

and door alarm*

Allows you to set the desired

temperature in the freezer

fWater filter change indicator*

cOn/Off sensor button for the

SuperCool function

* Only visible when the relevant

function is activated

Download from Www.Somanuals.com. All Manuals Search And Download.

Before use

Before using for the first time

Turning the appliance On/Off

^ Clean the inside of the appliance and ^ Open the appliance door.

the accessories with a mild solution

of warm water and liquid dish soap.

Dry with a soft cloth.

If the appliance was transported to

the installation site horizontally,

^ Turn the appliance On/Off with the

leave the appliance standing

main switch.

upright for approx. 8 hours before

connecting it to the electrical supply.

The main switch is located on the

This is very important to ensure

right-side underneath the control panel.

correct functioning.

Once on, the appliance begins cooling.

When the door is open, the interior

lights come on.

The access button will light in the

control panel.

The preset temperatures (factory

default settings) are reached after a few

hours. Do not put any food in the

appliance until the preset temperatures

are reached.

,^{Turning off the appliance with}

the main switch does not safely

isolate it from the power supply.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Using the settings

Additional settings

This appliance is operated with the use In the settings mode you can select

of touch keys activated by a finger. and change functions.

– An available button will appear white. In settings mode, certain settings can

be changed. The function possibilities

– A selected button will appear yellow.

are described in the respective

chapters of this manual.

Overview of the selectable function

settings:

^ Touch the access button "p" so it

turns yellow.

Function

Display text

To enter and exit the

Settings mode

On the control panel you will see

additional sensor buttons to operate the

appliance.

Temperature unit

°C - °F

†

These buttons allow you to:

– adjust the temperature,

(see "Setting the

temperature")

– select the SuperCool function, or

– turn the ice maker On/Off.

RemoteVision

;

Module settings

(optional accessory)

For additional information, see the

Button sound on/off

(see "Settings")

corresponding sections in this manual.

No function

^ To leave the settings menu, touch the

access button "p" so it turns white.

The last settings entered are stored.

If the access button is not pressed

the display will go out after approx.

30 secs.

The other sensor buttons now

disappear from the control panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Turning the button sound

On/Off

^ While holding down the X button,

press the access button "p" once.

Keep holding the X button down until

the following appears in the display

(approx. 5 seconds).

If you prefer the buttons to be silent

when touched the button sound can be

turned off.

^ Tap the X button until = appears in

^ Touch the access button "p" so it

turns yellow.

the display.

^ Touch the access button "p" to

confirm.

^ Note the position of the X button, but

do not touch.

^ By touching the X button, you can

choose between:

^ Touch the access button "p" again so

it turns white.

= 0 : Button sound is off

= 1 : Button sound is on

= – : Return to menu.

Only the access button "p" is visible.

^ Place one finger on the position of

the X button and hold (the X button

will not be visible).

^ Touch the access button "p" to

confirm the setting.

^ Tap the X button until you see ; in

the display.

^ Touch the access button "p".

You have now left the Custom settings

mode.

When you are in the Custom settings

mode the door alarm is turned off

automatically. Once the door is

closed it is reactivated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Turning off for longer periods

of time

If the appliance is not going to be used

for an extended time (for example,

during a vacation) some precautions

need to be taken:

^ Shut off the water supply line,

(several hours before switching off

the appliance)

^ Take all food out of the appliance

^ Turn the appliance off

^ Unplug the appliance

^ Empty the ice cube container

^ Clean the interior

^ Remove and discard the water filter

(secure the filter cap)

^ Leave the door open to prevent

odors

Download from Www.Somanuals.com. All Manuals Search And Download.

Temperature and door alarm

The appliance is equipped with an

alarm system, to ensure that the

temperature does not rise unnoticed

because of energy loss or an open

door.

Turning the temperature alarm Off

As soon as the alarm condition is

corrected, the alarm signal turns off

and the affected zone stops flashing in

the display. The "alarm" indicator goes

out.

The alarm system is always

operational, it does not need to be

switched on.

Temperature alarm

^ To turn the alarm off early, press

the "alarm" sensor button.

If the temperature becomes too warm,

an alarm sounds and the "alarm"

indicator turns red and flashes and the

temperature flashes in the control

panel.

The alarm signal turns off. The "alarm"

indicator remains on until the alarm

condition is corrected.

If the temperature in the freezer

zone reaches 0°F (-18°C) or higher,

check that food has not defrosted.

The temperature display shows the

highest temperature reached during the

alarm.

The alarm will sound and the display

will flash if:

Door alarm

If the appliance door is left open, an

alarm signal will sound and the "alarm"

indicator will turn red after five minutes.

– too much warm air flows into the

appliance, for example when food is

being loaded, re-arranged, or taken

out.

Once the door is closed the alarm will

turn off and the "alarm" indicator will go

out.

– large amounts of food are being

frozen at once.

Turning the door alarm Off

– the power fails.

To turn the alarm off early:

As soon as the alarm condition is

corrected the alarm with turn off and

the sensor button for alarm will go out.

^ The "alarm" indicator and signal will

turn off.

The alarm will turn off and the "alarm"

indicator will go out.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the temperature

Temperature range

The temperature can be set within the

following range:

7°F to -11°F (-14°C to -24°C).

To freeze fresh food and store frozen

food for an extended period of time, a

temperature of 0°F (-18°C) is

suggested.

^ Touch the access button "p" so it

turns yellow.

The room temperature and the

installation location can affect the time it

takes for the appliance to drop to the

coldest temperature. If the room

temperature is too high, it may not be

possible for the appliance to reach the

lowest temperature.

^ Use the X and Y buttons next to the

temperature display to set the

temperature warmer or colder.

Tap the X and Y sensor buttons to

raise/lower the temperature 1°, or hold

it down to move through the

temperature range more quickly.

The temperature display on the

control panel always shows the

desired temperature.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the temperature

Temperature unit

^ While holding down the X button,

press the access button "p" once.

Keep holding the X button down until

the following appears in the display

(approx. 5 seconds).

(Fahrenheit/Celsius)

The temperature can be displayed in

degrees Fahrenheit (°F) or Celsius (°C).

^ Touch the access button "p" so it

turns yellow.

^ Tap the X button until † appears in

the display.

^ Note the position of the X button, but

^ Touch the access button "p" to

confirm.

do not touch.

^ Touch the access button "p" again so

it turns white.

^ By touching the X button you can

select either Fahrenheit or Celsius for

the temperature display.

† 0: Fahrenheit

† 1: Celsius

† –: return to menu.

Only the access button "p" is visible.

^ Place one finger on the position of

the X button and hold (the X button

will not be visible).

^ Touch the access button "p" to

confirm the setting.

^ Tap the X button until a ; appears in

the display.

^ Touch the access button "p".

You have left the Custom settings

mode.

When you are in the Custom settings

mode the door alarm is turned off

automatically. Once the door is

closed it is reactivated.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the freezer efficiently

Freezing food

Placing food in the freezer

Fresh food should be frozen as quickly

as possible. This helps maintain the

nutritional value, vitamin content,

appearance and taste of the food.

Food to be frozen can be placed

anywhere in the freezer.

The freezer baskets can hold a

maximum of 35 lbs (16 kg) of frozen

food.

Never refreeze partially or fully

defrosted food. Consume defrosted

food as soon as possible, it will lose its

nutritional value and spoil if left for too

long. Do not refreeze defrosted food

unless it has been cooked.

^ Spread the food to be frozen across

the bottom of the freezer basket or

across the shelves, so that it will

freeze through to the core as quickly

as possible.

Before placing food in the freezer

^ When placing items in the freezer,

make sure the packaging and

^ When you are planning to freeze

large amounts of food (more than

4 ½ lbs [2 kg]), switch on the

SuperCool function ahead of time

(see "SuperCool").

containers are dry, to keep them from

sticking together when frozen.

When freezing, try not to let frozen

food come into contact with

unfrozen food, this could cause the

frozen food to defrost.

This will provide the food already in

the freezer with a protective boost of

cold air.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the freezer efficiently

Defrosting

Cooling drinks quickly

Frozen food can be defrosted in

different ways:

To cool drinks quickly, switch on the

SuperCool function. See "SuperCool" for

more information.

– in a microwave oven,

– at room temperature,

Do not leave bottles in the freezer for

more than 1 hour, closed containers

could burst.

– in the refrigerator (the cold given off

by the frozen food helps to keep the

other food cold),

– in a steam oven.

Poultry It is especially important to

observe proper hygiene when

defrosting poultry. Never save the liquid

from defrosted poultry. Drain it away

and promptly wash the container, the

sink and your hands. Danger of

salmonella poisoning.

Fruit should be defrosted at room

temperature in its packaging, or in a

covered bowl.

Most vegetables can be cooked while

still frozen. Simply place directly into

boiling water or hot oil.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the freezer efficiently

Freezing tips

– Do not place hot foods or drinks in

the freezer. This causes already

frozen food to thaw, and increases

the energy consumption

– The following are examples of foods

suitable for freezing:

Fresh meat, poultry, game, fish,

vegetables, herbs, fresh fruit,

pastry/dough, leftovers, and a range

of pre-cooked meals.

considerably. Allow hot foods and

drinks to cool down before placing

them in the freezer.

– The following examples of foods not

suitable for freezing:

Packing tips

^ Unsuitable packing material

- wrapping paper

Lettuce, radishes, sour cream,

mayonnaise, eggs in their shells,

onions, whole raw apples and pears.

- greaseproof paper

- cellophane

– To retain color, taste and vitamin C,

vegetables should be trimmed,

washed, and blanched.

- garbage bags

- plastic shopping bags

To blanch: bring a large saucepan of

water to a boil, then submerge the

vegetables in rapidly boiling water

for 2-3 minutes, depending on type.

Remove, and plunge into ice-cold

water to cool quickly. Drain and pack

for freezing.

Suitable packing material

- plastic freezer bags/wrap

- aluminum foil

- freezer containers

^ To help prevent freezer burn, expel

as much air as possible from

bags, etc., before sealing them.

– Lean meat freezes better than fatty

meat, and can be stored for

considerably longer.

^ Close the packaging tightly with

- plastic clips

- twist ties

– To prevent chops, steaks, cutlets or

rolled meats from freezing together in

solid blocks when packed, separate

with a sheet of plastic freezer wrap.

- rubber bands

^ Mark the package to indicate the

contents and the date of freezing.

– Do not season fresh foods or

blanched vegetables before

freezing. Cooked food can be lightly

seasoned before freezing, but care

should be taken as the taste of some

spices alters when frozen.

Download from Www.Somanuals.com. All Manuals Search And Download.

SuperCool

When the SuperCool function is

activated, the appliance is cooled as

cold as possible (to a factory-preset

temperature).

Switching off SuperCool

The SuperCool function automatically

switches off after approx. 52 hours. The

sensor button turns white, and the

appliance continues running at normal

power.

SuperCool

The SuperCool function is ideal for

freezing large quantities of unfrozen

food. Ideally the function should be

switched on 4 - 6 hours before the food

is placed in the freezer.

To save energy, you can switch off the

SuperCool function once the food is

sufficiently chilled.

If the max. freezing capacity is used,

24 hours are recommended.

This helps food to freeze quickly and

retain its nutrients, vitamins, flavor and

appearance.

^ Touch the SuperCool sensor so that it

turns white.

The temperature display returns to the

original temperature setting.

Switching on SuperCool

The appliance now continues running

at normal power.

^ Touch the SuperCool sensor so that

it turns yellow.

The temperature now begins to fall, with

maximum cooling performance.

The new temperature setting appears in

the display -22°F (-30°C).

Download from Www.Somanuals.com. All Manuals Search And Download.

Ice cube maker

Once the ice cube container is full, the

ice cube maker switches off

automatically.

For the automatic ice cube maker to

operate, it must be connected to the

household water supply. See

"Plumbing".

Do not use the ice cube container

for rapid cooling of food or drinks.

The ice cube maker may become

blocked and be damaged.

Turning on the ice cube maker

^ Make sure that the ice cube

container is under the ice cube

maker, as far as possible.

Do not use the first three containers

of ice cubes from the ice cube

maker.

Ice cubes will not be produced unless

the container is completely closed.

Discard the ice produced in the first

24 hours after switching on the ice

cube maker.

This applies for the very first use,

and whenever the appliance has

been out of service for an extended

period of time.

^ Touch the sensor button for the ice

cube maker so that it turns yellow.

The amount of ice cubes produced

depends on the temperature in the

freezer section. The lower the

As soon as the freezer has cooled to a

freezing temperature, the ice cube

container fills with water. Cold air is

blown directly over the container.

temperature, the more ice cubes will be

produced in a given period of time.

As soon as the ice cubes are frozen,

they fall into the ice cube container.

Turning off the ice cube maker

The ice cube maker can produce

approx. 120 ice cubes within 24 hours.

Note: Ice production will vary due to

your water supply temperature,

pressure and hardness.

The water supply line must be shut

off several hours before the

appliance or ice cube maker is

switched off.

The production volume of the ice

depends on the temperature in the

freezer. The lower the temperature the

more ice cubes produced.

After the appliance is turned on for the

very first time, it can take up to 10 hours

for the first ice cubes to drop out of the

ice cube maker and collect in the

container.

^ Touch the sensor button for the ice

cube maker so that it turns white.

Download from Www.Somanuals.com. All Manuals Search And Download.

Automatic defrost

The freezer defrosts automatically.

The moisture generated in the

appliance collects in the evaporator. It

is automatically defrosted and

dissipated by the condenser

periodically.

This automatic defrosting system

enables the freezer to remain

permanently ice-free, while ensuring

that the food stored in the freezer stays

frozen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the interior fittings

Moving the shelves

Replacing a door shelf

The shelves can be adjusted according ^ Start at the top of the slide-rails and

to the height of the food.

slide the shelf down into the desired

position.

^ Using both hands, grasp the shelf

from underneath and lift slightly so

that the rear of the shelf is slightly

above the mountings.

Freezer baskets

For easier loading, unloading, and

cleaning, the freezer baskets can be

shifted or completely removed.

^ Pull the shelf forward.

^ Move the shelf to the desired height,

then insert the (rear) hooks into

place.

^ Pull the basket forward until

resistance is felt.

On the hinged-side of the door is a

safety lock, which must be turned to a

horizontal position before the drawer

can be removed.

^ Make sure the shelf is level.

Top shelf

^ Lift the shelf up and out.

^ When replacing the shelf, make sure

that the latches on the corners at the

back are correctly engaged.

Adjusting the door shelves

For easier loading, unloading, and

cleaning, the door shelves can be

shifted or completely removed.

^ Using a suitable object, e.g., coin,

turn the safety lock to a horizontal

position a.

^ Using both hands, grasp the door

shelf by the frame and tip it slightly

forward.

^ On both sides of the basket, pull the

latches b upward and lift the basket

out of the freezer.

^ Slide the tipped shelf up or down

along the slide-rails, and click it into

place with the lower hooks.

Replacing the freezer basket

^ Make sure the shelf is level.

^ Fully extend the telescopic tracks.

^ Lay the basket onto the tracks so that

Removing a door shelf

it connects in the front and back.

^ Slide it upward all the way to the top

of the slide-rails, until it can be

removed.

^ Turn the safety lock back to the

vertical position.

^ Slide the freezer basket in.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the interior fittings

Ice cube container

The ice cube container is set on

telescopic tracks, and can be removed

for loading, unloading and cleaning.

^ Slide the container forward until

resistance is felt.

^ On both sides of the container, pull

the latches (see arrow) upward and

lift the container out of the freezer.

Push the tracks back into the freezer

to avoid injury.

Replacing the ice cube container

^ Completely extend the telescopic

tracks.

^ Lay the container onto the tracks so

that it connects in the front and back.

^ Slide the ice cube container

completely in.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

To better maintain your appliance

avoid the following:

To reduce the risk of electrical

shock, disconnect the appliance

from the power supply by shutting

off the power main, tripping the

circuit breaker or unplugging the

power cord before maintenance.

– cleaners containing soda, ammonia,

thinners, or chlorides

– cleaners containing descaling

agents or lime removers,

– abrasive cleaners,

Never use cleaning agents

– stainless steel cleaners,

– dishwasher soap (powder),

– caustic (oven) cleaners,

containing abrasive substances

such as sand, soda, acids, chlorides

or chemical solvents.

Non-abrasive cleaning agents are

also unsuitable, as they can cause

matte areas to appear.

– scouring pads, steel wool, hard

brushes,

– metal scrapers,

Only use a mild solution of warm

water and liquid dish soap to clean

this appliance.

– eraser sponges,

– steam cleaning products.

Glass cleaners may be used to

clean the exterior. However do not

allow them to sit or "puddle", this can

cause damage to the surface.

Remove the cleaner promptly.

Do not use a steam cleaner to clean

this appliance. Pressurized steam

could penetrate electrical

components and cause a short

circuit.

Do not allow water to get into the

electronic unit or lights.

The data plate located inside the

appliance must not be removed. It

contains information which is

required in the event of a service

call.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Before cleaning

Aluminum frames

The shelf frames and the door baskets

are made of aluminum.

^ Clean the frames with a mild solution

of warm water and liquid dish soap.

^ Use the main switch to turn the

Aluminum is susceptible to

appliance off completely.

scratches and nicks, treat with care.

The main switch is located on the right

side underneath the control panel.

The aluminum frames may become

discolored or otherwise altered if

soiling is not cleaned away

promptly.

^ Unplug the power cord.

^ Remove any food from the appliance

and store it in a cool place.

Do not use stainless steel cleaners;

lime removers; scouring pads, such

as pot scrubbers; or used sponges

that still contain abrasive cleanser

residue to clean the frames.

^ Take out any removable parts,

e.g., shelves.

Cleaning the interior and

accessories

Use a mild solution of warm water and

liquid dish soap. Wash all accessories

and drawers by hand. Do not wash in a

dishwasher.

^ Clean the appliance as needed.

^ After washing, wipe down the interior

and accessories with a clean wet

cloth, then dry with a soft cloth.

Leave the appliance door open for a

short time, so the moisture can

evaporate.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Ventilation slits

After cleaning

^ Check the ventilation slits in the base ^ Return all shelves and accessories.

panel regularly. Remove any

^ Shut the appliance door, plug in the

dirt/dust with a vacuum cleaner or

appliance and turn it on with the main

brush. Clean as needed.

switch.

^ Turn on the SuperCool function. The

Door seals

freezer section will cool down

quickly.

Do not use any oils or grease on the

door seals. This may cause the

^ Once the temperature is cold

seals to deteriorate and become

enough, place the freezer baskets

porous over time.

containing the frozen food into the

freezer.

^ Clean the door seals with warm water

^ Turn off the SuperCool function on a

temperature of 0 °F (-18 °C) is

reached.

and dry with a soft cloth.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Changing the light bulb

The lighting automatically switches off

after the door has been open for

approx. 5 minutes. This is not a fault.

After the bulb has cooled for a short

time it will turn on again.

If the light does not come on when the

door is opened briefly, the light bulb

should be changed.

^ Remove the defective light bulb.

^ Place the new bulb in the socket.

Halogen bulb type:

^ Use the main switch to turn the

appliance off.

20 W/12 V/socket GY 6.35.

To reduce the risk of electric shock,

disconnect the appliance from the

power supply by unplugging or

tripping the circuit breaker.

^ Slip the rear of the light cover back

into position, then pull it forward and

into place.

Upper lighting

^ Grasp the front of the light cover with

both hands, and slide it back.

^ Carefully pull the cover forward and

out.

Never touch a halogen bulb with e

fingers.

When inserting a glass halogen bulb

always hold with a soft cloth.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Side lighting

^ Turn the light cover counterclockwise

and pull out.

Never touch a halogen bulb with

bare fingers.

When inserting a glass halogen bulb

always hold with a soft cloth.

^ Pull the defective light bulb from the

socket.

^ Place the new bulb in the socket.

Halogen bulb type:

5 W/12 V/socket G 4.

^ Put the light cover back on and turn

clockwise into place.

^ Restore power to the appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Water filter

The appliance is supplied with an

active charcoal filter which improves

the taste and smell of ice cubes by

removing chlorine and other

substances from the incoming tap

water.

Note:

– After installing a new water filter and

switching on the ice maker, discard

the first 24 hours' worth of ice

production.

– If the ice maker has not been used

for a prolonged time discard any ice

cubes in the freezer, empty the

container and discard the ice

Additional water filters are available

from Miele.

production of the next 24 hours.

It is important to change the water

filter regularly.

– If the appliance or ice maker have

not been routinely used for several

weeks or months, or if the ice cubes

have an unpleasant odor, change

the water filter.

To avoid serious illness or death, do

not use water that is

microbiologically or chemically

unsafe or of unknown quality without

adequate disinfection or other

treatment before or after use of a

filter.

Water filter change indicator

The change indicator will appear

approx. every 6 months depending on

the quantity of ice produced.

– When the filter indicator lights red,

this is an indication that a filter

change will soon be necessary.

New water filters (Bypass and Active

charcoal filters) are available from

Miele.

^ When the filter indicator flashes red in

the display the filter must be

changed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Water filter

Exchanging the water filter

Note: Air trapped in the system may

cause water and the filter cartridge

to eject forcefully. Use caution when

removing.

^ Remove the cap from the used filter,

^ Take a new filter cartridge out of the

packaging and remove the protective

cap.

^ Push the cap onto the new filter

cartridge, 4.

^ Push in and rotate the filter cap on

the base panel of your appliance

counterclockwise 180°, 1.

^ Pull the used filter cartridge out of the

appliance, 2.

^ Push the filter cartridge with cap, in a

horizontal position, all the way into

the opening in the base panel, 5.

^ Rotate the filter cartridge clockwise

180° until the cap is in a horizontal

position, 6.

Download from Www.Somanuals.com. All Manuals Search And Download.

Water filter

Using an external water filter

If your household water supply already

has an external water filter installed,

leave the standard water filter (bypass

cartridge) installed in the appliance.

^ After the filter change the filter

indicator in the display still flashes.

The change must be be confirmed in

the electronic.

Confirming the filter change

^ Press and hold the filter change

sensor button.

^ At the same time place a finger on

the access button. Press and hold

both sensor buttons for approx. 5

seconds until a beep is heard.

The water filter change has been

confirmed and the filter change

indicator had been reset.

The filter change indicator goes out.

^ Close the door.

After installing a new water filter

discard the first 24 hours of ice

production.

Download from Www.Somanuals.com. All Manuals Search And Download.

Water filter

State of California

Department of Public Health

Water Treatment Device

Certificate Number

06 - 1775

Date Issued: March 10, 2006

Date Revised: April 3, 2008

Trad

mark/Mod

Designation

eplacement Elements

9000 077095

9000 077104

07134220

Miele 07134220

Manufacturer: Cuno, Incorporated

wat

r tr

atm

nt d

(s) list

d on th

s c

cat

hav

t th

irements pursuant to Section

116830 of th

th and Saf

ty Cod

for th

th relat

d contami

nants:

crob

Cysts

Turbidity

an c Contam

None

Contam

nants and Turb

Inor

ganic/Radiological Contaminants

None

inants

Rat

d S

Capacity: 740 gals

0.75 gpm

ow:

Rat

on:

d S

Cond

ons of C

rtificati

Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems certified for

cyst reduction may be used on disinfected waters that may contain filterable cysts.

Download from Www.Somanuals.com. All Manuals Search And Download.

Water filter

Performance Data Sheet For Filter Model 07134220

Using Replacement Cartridge 07134220

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances

listed below. The concentration of the indicated substances in water entering the system was reduced to a

concentration less than or equal to the permissible limit for water leaving the system, as specified in

NSF/ANSI 42 and 53.

Note that while the testing was

performed under standard

laboratory conditions, actual

performance may vary.

System tested and certified by NSF International in Model 07134220

against NSF/ANSI Standard 53 for the reduction of Cysts and

Turbidity and against Standard 42 for the reduction of Chlorine Taste

and Odor; Nominal Particulate Class I.

To a capacity of 739.68 gallons (2800 liters).

Substance

Average

Inﬂuent

Concentration

Inﬂuent Challenge

Concentration

mg/L

Product

Water

Concentration Reduction

Average Maximum Permissible

Max.

Min. %

NSF

Test

Product Water

Concentration

Efﬂuent Reduction

Cysts*

166500 Minimum 50,000/L

99.99

97.09

99.95

99.99

95.42

516458-05

516456-05

Turbidity

10.7

11 + 1 NTU

0.31

0.5 NTU

0.49

Particulate

Class I Particle size:

> 0.5 to < 1 um

Chlorine taste

and odor

At least 10,000

particles/ml

5700000

1.9

30583

0.05

99.52

97.3

> 85%

> 50%

69000

0.06

98.9

511079-03

511081-03

2.0 mg/L 10%

96.84

* Based on the use of Cryptosporium parvum oocysts

IMPORTANT: Must be installed and operated

in accordance with application guidelines.

Application Guidelines/Water Supply Parameters

Water pressure

Water temperature*

Service ﬂow

30- 120 psi (207 - 827 kPa)

33°F - 100°F (0.6°C - 38°C)

0.75 gpm (2.83 lpm)

Failure to do so may void warranty.

Change filter at least every 6 months.

Flush new cartridge for 3 minutes.

CAUTION: To avoid property damage due to water

leakage, you MUST read and follow these operating

instructions before installation and use of this

product.

For estimated costs of replacement

elements please visit your local appliance

dealer or parts distributor.

WARNING: Do not use with water that is

microbiologically unsafe or of unknown quality

without adequate disinfection before or after the

system. Systems certified for cyst reduction may be

used on disinfected waters that may contain filterable

cysts.

NSF is a registered trademark of NSF International.

CUNO is a trademark of 3M Company used under license.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lead free certificate

This product F 1411 Vi (KIMSDF18US) is tested and certified by WQA against

ORD0902 for California "lead free" compliance.

Miele & Cie. KG

Carl-Miele-Straße 29

D-33332 Gütersloh

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

With the aid of the following guide minor problems can be corrected without a ser-

vice call.

Repairs should only be carried out by a qualified and trained person in strict

accordance with local and national safety regulations. Unauthorized repairs

could cause personal injury or machine damage and may void the warranty.

Problems with temperature

Issue

Possible fault

Solution

The freezer

does not get

cold.

The machine is not

turned on.

Check whether the appliance is

turned on at the main switch. The

temperature display must be lit up.

The machine is not

plugged in.

Check that the plug is correctly

inserted in the power outlet.

Check that the fuse has Reset the circuit breaker.

not tripped.

If the breaker trips again the

appliance or the outlet may be

defective. Contact Miele or a

qualified electrician.

The temperature is set Check the display.

incorrectly.

The temperature Select a warmer

in the freezer is temperature.

too low.

See "Selecting the correct

temperature".

The SuperCool function SuperCool automatically shuts off

is still on. after 52 hours.

The door is not closed. Check that the door has been

closed properly.

A large amount of food This makes the compressor run

is being frozen at the

same time.

longer, causing the temperature to

fall automatically.

The freezer is

too warm.

The room temperature Raise the temperature of the room.

is lower than the Operating the appliance in a room

ambient temperature that is too cold will cause the cooling

for which the appliance system to switch off for too long,

is designed. causing the freezer section to

become too warm.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

General problems

Issue

Possible fault

Solution

Water is flowing out of Close the shut-off valve immediately.

the appliance.

Check whether the water

pipe in the appliance is

defective.

Contact Miele Technical

Service.

Check whether the water

pressure is too low.

Contact a plumber.

Check whether the correct Self-tapping valves and

water valve has been

installed.

3/16" (4.76 mm) saddle

valves reduce the water

pressure and can block

the pipe.

The door to the

This is not a fault.

Wait a few minutes, then

try again. It should now

open without force.

freezer section will not The suction caused by

open.

opening and closing the

door too many times in

succession prevents it

from opening.

The compressor kicks The ventilation slits are

Clean with a vacuum or

brush.

on very frequently and covered or dusty.

for too long.

The door has been

Once the freezer gets

opened too frequently, or a down to the set

large amount of unfrozen

food has been put in at

once for freezing.

temperature the

compressor will turn off.

The door is not closed.

Check that the door has

been closed properly.

The freezer runs

continuously.

To save energy the compressor runs at a lower speed,

but for longer when less cooling is required.

The temperature

This is not abnormal. When the ice maker is in use and

reading in the freezer the temperature of the room is above freezing the

shows -18°C, although temperature automatically stays at -18°C to ensure

a higher temperature proper functioning.

is set.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Alarm / Indicator warnings

Issue

Possible fault

Solution

The alarm is going off.

The appliance door(s)

have been open for

longer than 5 minutes.

Close the door.

The alarm is ringing and The door is not closed.

Once the alarm condition

has been corrected, the

alarm will turn off and the

"alarm" indicator will stop

flashing.

the "alarm" indicator is

A large amount of food is

flashing.

being frozen at the same

time.

There has been a power

failure.

The filter display is red. This is a warning that the Order replacement filters

water filter needs to be

changed soon.

from Miele.

The filter display is

flashing red.

The water filter needs to

be changed.

See "Exchanging the

water filter".

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problems with the ice maker

Issue

Possible fault

Solution

The ice cube maker

will not switch on.

The appliance is not

plugged in.

Check that the appliance is

connected to the power

supply.

The ice cube maker is When the appliance is turned on for the very first time, it

not producing any ice can take up to 10 hours for the first ice cubes to drop

cubes.

out of the ice cube maker and collect in the container.

The appliance is not turned Check that the appliance is

on.

switched on.

The water supply line was Contact Miele.

not primed (purged of air)

before the appliance was

used for the first time.

Check if:

See "Ice Cube Maker"

and/or "Plumbing" for more

information.

– the ice cube maker is

switched on.

– the water supply line is

open.

– there are ice cubes

stuck together and

blocking the exit.

– the ice cube container is

in the right position.

– the freezer compartment

temperature is too high.

– the water pressure is too

low. The water pressure

must be between 25 and

80 psi (1.7-5.5 bar).

Check whether the correct Self-tapping valves and

water valve has been

installed.

³/₁₆" (4.76 mm) saddle

valves reduce the water

pressure and can block the

pipe.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problems with the ice maker

Issue

Possible fault

Solution

The ice cubes are Other domestic appliances Avoid using such items as a

small.

that use water are in

operation.

dishwasher, washing

machine or shower at the

same time.

Check whether the water

filter needs changing.

See "Water filter" for more

information.

Check the water pressure.

The water pressure must be

between 25 and 80 psi

(1.7-5.5 bar).

Consult a plumber.

Check whether the correct

water valve has been

installed.

Self-tapping valves and ³/₁₆"

(4.76 mm) saddle valves

reduce the water pressure

and can block the pipe.

The ice cubes have When ice is stored for an

Use the ice maker more

frequently.

an unpleasant

odor/flavor.

extended period it may

absorb odors, which affects

the taste.

Check if the ice cube

container is dirty.

Clean the container.

Unsealed packages in the

freezer will transfer

odor/flavor particles to the

ice cubes.

Check that food has been

packed in airtight

containers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problems with the ice maker

Issue

Possible fault

Solution

The ice maker is not

producing enough ice

or the ice cubes are

misshapen.

Check the water

Contact a plumber.

pressure. The water

pressure must be

between 25 and 80 psi

(1.7-5.5 bar).

Check that the freezer

temperature is too high.

See "Selecting the correct

temperature".

Change the water filter.

See "Water filter".

Ice is forming in the

supply hose to the ice

maker.

Check the water

Contact a plumber.

pressure. The water

pressure must be

between 25 and 80 psi

(1.7-5.5 bar).

Check whether the

See "Selecting the correct

temperature".

freezer compartment

temperature is too high.

Download from Www.Somanuals.com. All Manuals Search And Download.

After sales service

In the event of a fault which you cannot MieleCare

easily fix yourself, please contact the

(USA only)

Miele Technical Service Department at

the address on the back of this booklet. MieleCare, our Extended Service

Contract program; gives you the

When contacting the Technical Service

assurance of knowing that your

department, please quote the model

appliance investment is covered by 5

and serial number of your appliance

years of worry-free ownership.

given on the data plate inside the

MieleCare is the only Extended Service

appliance.

Contract in the industry that guarantees

repairs by a Miele Authorized Service

Provider using genuine Miele parts.

Only genuine Miele parts installed by

factory-trained professionals can

guarantee the safety, reliability and

longevity of your Miele appliance.

Please note that unless expressly

approved in writing by the Miele Ser-

vice department, Extended Service

Contracts offered by other providers for

Miele products will not be recognized

by Miele. Our goal is to prevent

unauthorized (and untrained) service

personnel from working on your Miele

products, possibly doing further

damage to them, you and/or your

home.

To learn more about MieleCare

Extended Service Contracts, please

contact your appliance dealer or visit

us online at:

http://mieleusa.com/mielecare

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Instructions

Information is subject to change. Please refer to our website to obtain the most

current product specification, technical & warranty information.

To prevent accidents

and machine damage

read these instructions

before

installation or use.

Download from Www.Somanuals.com. All Manuals Search And Download.

Caring for the environment

Disposal of packing materials

Disposal of an old appliance

The cardboard box and packing

materials are biodegradable and

recyclable. Please recycle.

Old appliances contain materials that

can be recycled. Please contact your

local recycling center about the

possibility of recycling these materials.

Ensure that any plastic wrappings,

bags, etc., are disposed of safely and

kept out of the reach of babies and

young children. Danger of suffocation!

Before discarding an old appliance,

disconnect it from the electrical supply

and cut off the power cord to prevent it

from becoming a hazard.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Installation site

Have the appliance installed by a

qualified technician, according to

the enclosed installation instructions.

The appliance should be installed in a

dry, well ventilated room.

Do not install the appliance:

- outdoors,

WARNING

- in an environment with dripping

water,

This appliance is top-heavy and

must be secured to prevent it from

tipping forward.

- in rooms which are at risk of frost.

Keep the door closed until the

appliance is completely installed

and secured as per the installation

instructions.

The installation location should not be

exposed to direct sunlight, nor near a

heat source, such as an oven,

radiator, etc.

The ambient temperature should not

drop below 55°F (13°C) or rise above

110°F (43°C), otherwise malfunctions

may occur.

Empty weight of your machine:

F 1411 Vi . . . . . . . . . . 317 lbs (144 kg)

If installation next to a heat source is

unavoidable observe the following

minimum distances from the heat

source:

– 1 ¹/₄" (3 cm) from an electric cooktop

or electric oven.

– 12" (30 cm) from a gas or oil

cooktop, range or oven.

The following should also be taken into

consideration:

– The electrical outlet must be easily

accessible in case of an

emergency,not concealed behind

the appliance.

– The plug and cord must not touch

the rear of the appliance as they

could be damaged by vibrations

from the appliance.

– Do not plug in other devices behind

this appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Important! When there is high

humidity a build-up of condensation

on the outer surfaces of the

appliance can occur.This can cause

the surfaces to corrode.To prevent

this, it is advisable to install the

appliance in a dry and/or an

air-conditioned room with sufficient

ventilation.Please ensure that doors

close and seal properly after

installation and that the appliance is

installed in accordance with these

installation instructions and and with

the required ventilation openings.

– If the room is too cold, it will cause

the cooling system in the appliance

to remain off for too long.This can

cause the temperature in the

appliance to rise, resulting in

damage.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Base

Ventilation

A fully loaded appliance is very heavy.

The load-bearing capacity of your floor

must meet the following requirements.

The approx. weight of a fully loaded

machine is:

The air intake and outlet must not be

blocked or covered in any way. They

also need to be dusted/cleaned on a

regular basis.

Installation niche

F 1411 Vi . . . . . . . . . . . 584 lbs (265 kg)

To ensure safe, trouble-free installation

and the best possible cosmetic result,

check to be sure that the installation

space complies with the installation

dimensions. See "Niche dimensions".

To ensure that the appliance is installed

securely and functions properly, the

base must be flat, level and made of a

hard, rigid material.

If in doubt, contact Miele.

The side walls of the installation cavity

must be plumb.

Furniture/fixtures

The minimum thickness of the side

walls and the top wall must be ⁵/₈"

(16 mm).

The new appliance will be mounted

securely to adjacent and overhead

furniture/fixtures.

The minimum thickness of the toe-kick

panel must be ½" (13 mm). A thickness

of ³/₄" (19 mm) is recommended.

For this reason it is essential that all

attachable furniture/fixtures are

connected securely to the base or the

wall by suitable means.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Stainless steel panels

Side-by-side

Stainless steel door panels and toe-kick This appliance can be installed

covers are available from Miele.

"side-by-side" with another

fridge/freezer using a "Merging Kit".

Custom door panels

The "Merging Kit" is available from

Miele.

This appliance is compatible with all

styles and designs of kitchen cabinetry.

Contact Miele or your dealer for

specific information about which

combinations will work with your

appliance.

The total weight of the decorative

panel(s) must not exceed the following:

F 1411 Vi . . . . . . . . . . . 123 lbs (56 kg)

For instructions on how to attach the

appliances and install the heating

mat, please refer to the instructions

included with the "Merging Kit",

available from Miele.

Fitting a door panel which is heavier

than the max. permitted could

damage the hinges.

Installation options

There are many different installation

options. You are limited only by the

design of the kitchen.

Installation without a partition using

the "Merging Kit"

The door hinge cannot be

exchanged.

Single column

The appliance can be installed at any

preferred location in the kitchen.

However, be sure the door will open

and close properly in the chosen

location.

If the appliances are installed directly

next to each other (without a partition),

they need to be attached together

using the "Merging Kit".

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Installation with partition using the

"Merging Kit"

Side panels

If one side of the appliance is visible, a

side panel must be used.

The minimum thickness of the partition

is ⁵/₈" (16 mm).

The side panel must be firmly secured

to the wall, the floor and the overhead

furniture/fixtures before the appliance is

placed in the cavity.

The dimensions of the side panel are

taken from the opposite wall of the

installation space. During installation,

ensure that the cavity is square and the

measurements are correct.

If there is a partition with a thickness

from ⁵/₈" (16 mm) to 6 ⁵/₁₆" (160 mm)

between the adjacent appliances, then

each appliance should be individually

installed within its own niche using the

mounting accessories included.

The "Merging Kit" will also be needed.

The "Merging Kit" is available from

Miele.

Installation with partition without

using the "Merging Kit"

If there is a partition with a thickness of

more than 6 ⁵/₁₆" (160 mm) between

the adjacent appliances, then each

appliance should be individually

installed within its own niche using the

mounting accessories included (the

"Merging Kit" is not necessary).

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensions

Door dimensions (open 115°)

F 1411 Vi

20 ¹¹/₁₆"

Door front max.

1 1/2" (38 mm)

Door

handle

9 ³/₁₆"

(234 mm)

(525 mm)

The dimensions of the door fronts and handles will vary according to each

individual kitchen.

Miele recommends using the full door opening angle of 115° for this freezer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensions

Niche dimensions

Niche width (A)

F 1411 Vi

18" (457 mm)

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensions

Power supply and water connection

1. Power supply

2. Water connection

F 1411 Vi

9" (229 mm)

Install a pressure limiting device and water hammer arrester for inlet water

pressures exceeding 80 psi.(Refer to Uniform Plumbing Code, Sections 608.2

and 609.10) Never install or operate where inlet water pressure may exceed

120 psi.

Door front dimensions

F 1411Vi 79 ⁷/₈"

17 ³/₄"

(2029 mm) (451 mm)

4" - 5 ³/₁₆" (102 - 132 mm)

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Before you begin

– Multi-grip pliers

– Level

Read these instructions completely

and carefully.

– Tape measure

– Square

Have the appliance installed by a

qualified technician, according to

the enclosed installation instructions.

When fastening the cabinet to the wall

behind it (see "Installing the appliance")

use:

To reduce the risk of injury or

damage to the product, two people

should be used for installation.

– suitable plugs/screws depending on

the type of wall.

– several mounting brackets, if

required.

These installation instructions are

intended for use by qualified installers.

In addition to these instructions, the

appliance must be installed in

accordance with all local codes. In the

absence of a local code, the following

should be used:

Other

– Stepladder

– Dolly, hand truck

– Wooden beam (cross section

min. 3" x 4" [75 mm x 100 mm] as an

alternative tilt protection, length

depends on the width of the

installation niche)

– In the USA, the National Electric

Code, ANSI/NFPA 70 - latest

edition/State and Municipal codes

and/or local codes.

– In Canada, the Canadian Electric

code C22.1 - latest edition/Provincial

and Municipal codes and/or local

codes.

– Wood screws in different sizes

– Edge protector(s)

Optional accessories

Tools needed for installation

– Cordless screwdriver

– Torx screwdriver

– "Merging Kit" for side-by-side

installation

– RemoteVision module for wireless

monitoring

– Hammer drill

– Wood drills in different sizes

– Hammer

– Rachet 5/16" (8 mm)

– Adhesive tape

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Aligning the housing unit

Check the installation niche

To ensure a safe, trouble-free

installation and the best possible

cosmetic result, check to be sure

that the installation space complies

with the installation requirements.

^ Check the base (see "Installation").

^ Check the dimensions of the cavity.

^ Check that the cavity is square.

^ Check the location of the power

outlet.

^ Check the location of the water

connection (see "Plumbing").

The housing unit must be carefully

aligned using a spirit level before

installing the appliance. The unit

corners must be at right angles, as

otherwise the furniture door will not

align correctly with the 4 corners of the

appliance.

^ Check that all furniture parts in the

vicinity of the appliance are securely

connected to the wall.

^ Check that the adjacent

furniture/fixtures do not collide with

the open door.

– The side panels of the housing must

be even.

Before installation

,^{Caution - the appliance is very}

heavy. Use caution when unpacking

and opening the door, danger of

tipping.

– The housing unit panels must be at

least 16 mm thick.

The plinth facing must be at least 13

mm thick (or preferably 19 mm).

^ To protect the base from damage

during installation, attach a hard

board, linoleum, etc., to the floor in

front of the intended installation

location.

^ Take the supplied accessories out of

the protective packaging.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

^ From the rear of the appliance

carefully lift it from the pallet.

Once the appliance is on the ground it

can be wheeled around.

RemoteVision module

installation

(optional accessory)

^ Do not remove the installation

supports from the appliance door.

They will be used later in the

installation niche.

Always disconnect the appliance

from the power supply when

performing installation, maintenance

or service work.

There are transportation safety

devices inside the appliance to

protect the shelves and storage

compartments until installation is

complete. Do not remove them, or

parts may be damaged.

Install the RemoteVision module

before placing the appliance in its

installation niche.

Once connected the RemoteVision

module will increase the energy

consumption of the appliance.

^ Check the appliance for damage in

The slot for the RemoteVision module is

located in the lower area of the back of

your appliance.

transit.

Do not install the appliance if it is

visibly damaged. If in doubt, contact

your dealer.

^ Unscrew the screws a on the cover

b and pull off the sticker c.

^ Loosen the bracket that holds the

appliance to the pallet.

^ Remove the cover b.

,^{Caution! The appliance is no}

longer secured and may be unstable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

^ Push the module into the slot until it

locks into place.

^ Pull the antenna d straight out.

^ Connect the appliance to the power

supply and turn it on. After several

seconds the indicator light e will

come on.

^ Guide the cover b over the antenna

d and screw on the cover.

^ Angle the antenna d so that it faces

to the right or left.

The indicator light will display different

colors one after the other; any control

light at the end indicates that the

module was correctly installed.

If necessary, disconnect the power

supply and continue installing the

appliance.

If the indicator light does not come on,

installation of the module was

Preparing the installation

niche

unsuccessful. In that case, repeat the

process. If that does not correct the

problem, contact Miele.

,^{Keep the appliance door closed}

until it is securely fastened in the

niche. Tipping hazard.

Because of the size and weight of

the appliance, it is essential to

ensure that the appliance cannot tip

over once it has been mounted in

the niche.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Mounting Accessories

The mounting accessories needed for

installing the appliance into the niche

are included in the packaging. Several

plastic bags are included which are

marked alphabetically.

The bag needed for each step will be

marked with its respective letter.

Two anti-tip brackets are

recommended for each appliance. For

side-by-side installations 4 brackets are

recommended.

Anti-tip brackets

The anti-tip brackets a keep the

appliance safely secured in the

installation niche b and prevent it from

tipping.

^ Position the anti-tip brackets on the

left and right in the installation niche

so that there is no more than 3/8"

(10 mm) of space between the

brackets and the side walls.

^ Mark the drill holes in the anti-tip

brackets on the back wall and on the

ceiling of the installation niche.

^ Set the brackets aside - they will be

needed again later.

Screws are supplied with the

appliance for various

applications/materials.

,^{Risk of tipping}

The installation niche must be

securely attached to the wall behind

it. This is the only way the appliance,

which is later secured in the niche,

can be prevented from tipping!

If the anti-tip brackets cannot be

attached securely with the screws

supplied, an alternative anti-tip

device can be used.

Ensure that there are no electrical

wires or plumbing in the area which

the screws could penetrate - risk of

injury and damage.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

In a cabinet without a back wall

^ Now attach the installation niche to

the wall.

The built-in cabinet must be secured to

the wall behind it with several screws.

In a cabinet with a back wall

^ screw the cabinet to the wall behind

it in several places using suitable

mounting brackets.

For this, use suitable plugs/screws

depending on the type of wall.

^ screw the back wall of the cabinet in

several places directly to the wall

behind it.

For this, use suitable plugs/screws

depending on the type of wall.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Securing an alternative anti-tip

device

– If the installation niche is deeper than

the appliance, select a beam with a

larger cross section, or attach two

beams.

If the anti-tip brackets cannot be

attached securely, an alternative

anti-tip device can be used.

– The beam must cover the appliance

by at least 2" (50.8 mm).

Ensure that there is no "give" between

the appliance and the anti-tip device.

^ Mark the installation height (lower

edge of the beam) on the rear wall of

the niche.

^ Select screws according to the

thickness of the wooden beam.

Example: 3 ½" screw for 2x4 beam.

Determine the number of screws

based on the niche width, to ensure

that the beam will be attached

securely.

^ Locate wall studs near the rear wall

of the cavity and mark drill holes in

the beam.

^ Pre-drill the wooden beam.

^ Attach the wooden beam to the rear

wall of the niche.

Now prepare the water connection

from the appliance to the main

supply line (see "Plumbing").

If possible, always screw the

wooden beam to existing studs.

– Cut a wooden beam

(cross section min. 3" x 4"

[75 mm x 100 mm] to the required

length).

– The length is equal to the width of

the installation niche.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Sliding the appliance into the

niche

^ Plug the appliance into the power

outlet a.

The plug of the appliance should be

easily accessible after installation.

If the plug is not accessible after the

appliance has been installed,

disconnection from the power

supply should be completed via the

circuit breaker.

If a side-by-side installation is

desired, connect the two appliances

together. See the Installation Manual

included with the "Merging Kit".

In the case of side-by-side

installations, a separate outlet must

be used for each appliance.

^ To prevent the power cord from

becoming caught:

Tie a piece of string to the middle of

the power cord and feed it forward

under the appliance. When sliding

the appliance in, pull the cable

forward b.

^ Unscrew the plinth.

^ Carefully slide the appliance into the

space.

If resistance is felt when attempting to

slide the appliance into the installation

niche - for example, because the floor

is uneven,

^ Turn the rear adjustable wheels slightly

outward (see "Aligning the appliance"),

then push the appliance in.

Be careful not to damage the water pipe

or power cord attached to the floor.

^ Remove the edge protectors.

^ To protect the corners of the

installation space, attach edge

protectors where needed (not

included).

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Aligning the appliance

Important!

^ Align the appliance with the custom

When unscrewing the

front.

height-adjustable feet, proceed

gradually, alternating between left

and right.

^ Unscrew the height-adjustable feet

until the mark on the base has

reached the indicated guide

dimension 1 1/4" (32 mm). The guide

dimension of 1 1/4" (32 mm) is

related to a niche height of 84"

(2134 mm).

The installation aids c on the

appliance door have been designed for

custom door thicknesses of 3/4"

(19 mm) and 1 1/2" (38 mm).

The height-adjustable feet at the front

and rear can all be adjusted from the

front:

– Front feet:

Adjust with a rachet 5/16" (8 mm) d

– Rear feet:

^ Align the appliance again using a

Adjust with a (cordless) screwdriver

and/or a rachet 5/16" (8 mm) for fine

adjustment e

level.

Note:

^ Use a level to align the installation

– When unscrewing the

height-adjustable feet, proceed

gradually, alternating between left

and right.

aids c on the door.

– If using a wooden beam as an

alternative anti-tip device, rotate the

appliance all the way toward the

wooden beam.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Attaching the appliance to the

installation niche

^ Secure the attachment plate side lugs.

If there is a fairly large gap above the

appliance, cut a wooden beam to fit

exactly and place it in the gap.

^ Screw the attachment plate lugs f to

the overhead furniture/fixtures.

^ If necessary, shorten the filler strip h

to the required height.

If there is no way to attach the top of

the appliance, it can be attached to the

sides of the installation niche.

^ Place the 2 strips on top of each

other i.

^ Insert the filler strip until you hear it

click into place j.

^ Pull out the plate side lugs g.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

For a side-by-side combination the filler ^ Open the appliance door.

strips from both appliances are put

together to form one long filler strip:

^ Take the peg from the "Side-by-side

Merging kit" and insert it halfway into

the filler strip rail on the left-side

appliance.

^ Place the second filler strip on the

peg and press both filler strips

together.

^ Screw the attachment plate lugs k to

the adjacent furniture/fixtures.

With side-by-side combinations, only

the external side of the appliances can

be secured to the niche.

^ Insert both filler strips into the

installation space above the

appliance, until they click into place.

Now connect the water supply to the

appliance (see "Plumbing").

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Preparing the custom door

^ Open the appliance door.

^ Unscrew the installation supports l

from the appliance door.

^ Measure the distance X between the

bracket from the door and the

overhead furniture/fixtures.

^ Loosen the remaining screws from

the strips m on each side of the door,

then remove.

^ Loosen the two nuts.

Set aside the nuts - you will need

them again later.

^ Set aside the screws and side strips

m - you will need them again later.

^ With the inside facing up, lay the

custom door on a stable surface (to

avoid scratch marks, place some

plastic or a cloth on the surface).

^ Remove the light switch cover (see

arrow).

^ Close the appliance door.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

The bracket includes a variety of holes

for the various design options of

custom doors.

When performing work on the custom

door, always observe the following:

– Always select the best load-bearing

surface of the custom door as the

location for screws.

– Always select a screw length that is

shorter than the thickness of the door

front.

^ Secure the door handle to the front of

the appliance from the inside.

^ Mark the distance X on the back-side

of the custom door.

^ Also calculate and mark the center of

the custom door Y.

^ Remove the mounting frame from the

appliance door and position it

according to the markings on the

custom door.

^ Pre-drill the holes.

^ Tightly screw on the bracket using

the pre-drilled holes:

Attach the bracket to each

attachment point with at least one

screw.

^ Attach the bracket at the top with at

least 6 screws.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Attaching and aligning the

custom door front

^ Align the custom door height with the

threaded bolts n.

^ Now tighten the nuts o on top. This

secures the appliance door.

^ Open the door and hang the custom

door with the mounting frame over

the threaded bolts n.

^ Put the side strips m back into place

and screw them completely down on

both sides of the appliance door.

Bag E contains spare screws for this

purpose.

^ Screw the nuts o a few turns onto

the threaded bolts n. Do not tighten

the nuts completely.

^ Close the appliance door and check

the distance to doors of adjacent

furniture/fixtures.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Attaching the covers

^ Insert the cover strip into the space

between the appliance and the side

panel.

^ To mount the cover strips on both

sides of the door, click them into

place from bottom to top, into the

gap between the appliance door and

the custom door.

For side-by-side combinations, the

cover strips (on both sides of the

appliance) are applied to the

outermost spaces only.

^ Attach the light switch cover.

^ Screw the brackets onto both sides

of the appliance, to hold the cover

strip.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Attaching the toe-kick cover

^ Remove the foil from the adhesive

strips.

The maximum height of the toe-kick

cover is 4" (102 mm) from the top of

the floor. Do not cover the ventilation

slits in the plinth. Risk of damage to

the appliance.

^ Attach the toe-kick cover to the

plinth.

^ If required, cut the toe-kick cover to

the required length and height.

^ Attach the plinth to the appliance,

and put the included cover plates in

place.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing the appliance

Mounting the air separator

The air separator keeps the supply and

exhaust air separate. This prevents

warm exhaust air from flowing into the

machine, optimizing the energy

performance of the unit.

^ Position the air separator in the

center of the appliance door.

^ From below, screw the air separator

firmly onto the door with the 2

screws.

^ If necessary, shorten the three parts

of the air separator.

^ Insert the foam pieces back into the

sides.

Download from Www.Somanuals.com. All Manuals Search And Download.

Plumbing

All plumbing work should be carried

out by a suitably qualified and

competent person, in accordance

with all applicable local and national

regulations.

The shut-off valve for the water

connection must not be located

behind the appliance. It is

recommended to place the shut-off

valve directly next to the appliance

(base unit) or in another easily

accessible location.

Disconnect the appliance from the

electrical power supply before

connecting it to the water supply.

Do not use pipe extenders.

Turn off the water supply before

connecting the water lines to the ice

cube maker.

In the event that the piping has to be

replaced only Original Miele Spare

parts are suitable for use. Contact

Miele.

The water quality must conform to

country requirements for drinking

water.

– The appliance is only suitable for

connection to the cold water supply.

– The water pressure must be between

25 and 80 psi (1.7-5.5 bar).

– A separate shut-off valve must be

installed, so that the water supply

can be interrupted as needed.

– The maximum outer diameter of the

water pipe (without fittings):

³/₈" (10 mm).

Download from Www.Somanuals.com. All Manuals Search And Download.

Plumbing

Preparing the water connection For appliances with a hose guide

The connection to the household

water supply must be installed

before the appliance is installed.

^ Turn off the main water valve to prevent

damage caused by leaking water.

^ Attach the connecting pipe to the

shut-off valve, according to the

instructions supplied by the

manufacturer of the ice cube maker

installation kit.

^ position the device in front of the

niche and push the stainless steel

tube through the hose guide at the

back of the unit.

^ Install the connecting pipe. Always

observe the indicated clearance

dimensions to prevent damage to the

connecting pipe when pushing in the

appliance.

At this point the niche should be ready

for the appliance to be pushed back

into it (see "Installing the appliance").

^ You can now continue with the

installation.

^ Secure the connecting pipe to the

floor with adhesive tape.

^ You may now proceed to install the

appliance. See "Installing the

appliance".

Download from Www.Somanuals.com. All Manuals Search And Download.

Plumbing

Connecting the water supply

^ Push the union nut and seal onto the

water pipe.

When connecting the water pipe to

the solenoid valve of the appliance,

follow the instructions supplied by

the manufacturer of the ice cube

maker installation kit.

^ Push the end of the water pipe into

the appliance connection and screw

on the union nut, 3. First tighten by

hand.

^ Then use an open-ended wrench to

tighten the union nut. Do not over

tighten.

When bending the water pipe, be sure

not to kink it, otherwise there is a risk of

leaks and water damage.

^ Open the shut-off valve and the main

water connection. Check for leaks at

the connection for the shut-off valve

and to the appliance.

Use bending aids.

^ Turn the appliance on.

After a maximum of 10 hours the first

ice cubes will drop out of the ice

cube maker and collect in the ice

cube container.

^ Remove the cap from the appliance

connection, 1.

^ Bend the water pipe to suit the

location of the connection on the

appliance, 2.

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical connection

The appliance is supplied with a

UL-listed, 3-wire power cord and

NEMA 5-15 P plug ready for connection

to a 120 V, 60 Hz supply.

, ^{Avoid the risk of electrical}

shock

- Plug into a grounded 3-prong

outlet.

The fuse rating is 15 amps.

- Do not move the ground plug.

- Do not use an adapter.

- Do not use an extension cord.

The appliance requires a 3-wire

receptacle.

The receptacle must be installed by a

licensed electrician only.

Failure to follow these instructions

can result in death, fire, or electrical

shock.

In the case of side-by-side installations,

a separate outlet must be used for each

appliance. Ideally, the power outlet

should be next to the appliance and

easily accessible. Do not connect the

appliance to the power supply by an

extension cord. Extension cords do not

guarantee the required safety of the

appliance (danger of overheating).

Improper connection of the

equipment grounding conductor

may result in electric shock. If you

are in any doubt as to whether the

appliance has been properly

grounded, have the appliance

checked by a qualified electrician or

service technician.

If any changes are needed to the

household wiring or power supply, this

work must be performed by a qualified

electrician.

Installation, repairs and other work

by unqualified persons could be

dangerous.

Before installing the appliance,

verify that the voltage, load and

circuit rating information found on

the data plate match the household

electrical supply.

If there are any questions regarding the

electrical connection of this appliance

to the power supply, please consult a

licensed electrician or call the Miele

Technical Service.

U1-800-999-1360

V1-800-565-6435

Download from Www.Somanuals.com. All Manuals Search And Download.

RemoteVision (optional accessory)

Miele's RemoteVision Wi-Fi technology

creates a 'virtual link' between your

appliance and our monitoring center. If

a fault occurs, Miele's client service

center will be notified and contact you,

or another trusted individual identified

on your call roster, in order to gain

access to your appliance to fix the

problem.

Be sure your wireless system meets the

following requirements

– A wireless router that supports an

IEEE 802.11b protocol

– Windows XP^®or newer operating

system, Mac^®OS X 10.3 or higher

– Cable or DSL modem

– Microsoft^®Internet Explorer 6 or

higher, Safari 2.0 or higher, Firefox

1.5 or higher

For information on set-up and

installation of the RemoteVision module

see the "Installation" section of this

manual.

* Please note that each wireless router

manufacturer supplies their own device

drivers and setup programs. Due to the

differences in manufacturers, exact

router setup instructions are not

included in this manual. Wording and

instructions may vary.

Download from Www.Somanuals.com. All Manuals Search And Download.

RemoteVision (optional accessory)

Accessing the RemoteVision

^ Tap the X button until ; appears in

the display.

control panel

^ Touch the access button "p" to

confirm.

See the table on the following page for

a description of each setting in the

display.

^ Touch the access button "p" so it

turns yellow.

^ Use the Y or X buttons to select the

^ Note the position of the X button, but

RemoteVision options.

do not touch.

^ Touch the access button "p" again so

it turns white.

The module has been connected to

the network when ; # appears in the

display.

Only the access button "p" is visible.

If ; # does not appear, refer to the

"Network options" section of the

XKM 2000 Installation Instruction

manual.

^ Place one finger on the position of

the X button and hold (the X button

will not be visible).

^ While holding down the X button,

press the access button "p" once.

Keep holding the X button down until

the following appears in the display

(approx. 5 seconds).

^ Press and hold the access button "p"

for 2 seconds to confirm the change.

^ To return to the main menu, tap the X

button until a solid ; - appears in the

display.

^ Press the access button "p" to

confirm.

^ Tap the X button until a ; appears in

Access to the Custom settings mode is

now active for approximately 10

seconds.

the display.

^ Touch the access button "p".

You have left the Custom settings

mode.

When you are in the Custom settings

mode the door alarm is turned off

automatically. Once the door is

closed it is reactivated.

Download from Www.Somanuals.com. All Manuals Search And Download.

RemoteVision (optional accessory)

MasterCool control panel options for RemoteVision

Status indicators Description of function

Flashing ; ~

Flashing ; ‡

Flashing ; |

Module booting phase

Not connected to network

Connection to network established, no IP address

assigned

Solid

; #

Connected to network

Flashing ; <

In Ad-Hoc Mode, not connected

In Ad-Hoc Mode, connected

Flashing ; =

Selectable

options

Description of function

; -

; 2

; 3

; 4

Back

Reboot the module

Reset to factory settings

Enter Ad-Hoc Mode

Note: If you cannot select any option (other than ; - "Back", the module has not

been installed correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alteration rights reserved / 0414

M.-Nr. 09 743 780 / 01

INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST

CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.

Download from Www.Somanuals.com. All Manuals Search And Download.

NetComm Network Card NP6800 User Manual
NETGEAR Network Router R6220 User Manual
Nortel Networks Network Router 5000i User Manual
Omega Speaker Systems Automobile Parts 23221 User Manual
Optimus Cassette Player SCT 540 User Manual
Optiquest Computer Monitor VS12087 User Manual
Oregon Scientific Clock RRM326P User Manual
Oregon Scientific Heart Rate Monitor SE138 User Manual
Packard Bell Server MH4000 User Manual
Panasonic Network Card 2SC4835G User Manual