Operating and installation instructions
Gas hobs
CS 1012-1
CS 1034-1
en - GB
To avoid the risk of accidents or
damage to the appliance it is
essential to read these
instructions before it is installed
and used for the first time.
M.-Nr. 09 094 640
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CS 1012-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CS 1034-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Rapid ignition system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Switching on, adjusting the flame and switching off . . . . . . . . . . . . . . . . . . . . . . . 22
In-operation indicator and Residual heat indicator . . . . . . . . . . . . . . . . . . . . . . . . 24
Suitable pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Energy-saving tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Stainless steel surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Pan supports, control knobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Burner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Safety instructions for installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Appliance and building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CS 1012-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CS 1034-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing the worktop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Installation of several appliances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Fixing the spring clamps and spacer bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Installing / removing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
General installation tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Conversion to another type of gas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
CS 1012-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Jet table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
CS 1034-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Jet table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Changing the jets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Function test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
After sales service, data plate, guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas-heated appliances
Safety precautions to take if you smell gas
ß Turn off the gas emergency control valve immediately.
This is usually located near the gas meter.
ß Eliminate all sources of ignition in a safe manner.
Do not smoke, light cigarette lighters or matches.
ß Do not operate electrical lights or switches, i.e. do not switch them "On" or "Off".
ß Open all doors and windows to ventilate the area.
ß If the smell of gas persists, evacuate the building.
In the UK you must now:
ß Call the Gas Emergency Contact Centre (Tel: 0 800 111 999)
For any gas work in the UK always use a Gas Safe registered engineer.
In other countries please follow relevant country specific procedures on gas.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
CS 1012-1
aLarge burner
bMedium burner
cPan support
Controls:
frear
gfront
dSymbols to indicate which gas
burner the control is for
eDisplay
Display
lIn-operation indicator
mResidual heat indicator
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
CS 1034-1
aLarge burner
bSmall burner
cLarge burner
dMedium burner
ePan supports
Controls:
hfront right
irear right
jrear left
kfront left
fSymbols to indicate which gas
burner the control is for
gDisplay
Display
lIn-operation indicator
mResidual heat indicator
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Burner
nBurner cap
oBurner head
pIgnition safety device
qIgnitor
rBurner base
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This appliance complies with all current local and
national safety requirements. Improper use can,
however, present a risk of both personal injury and
material damage.
To avoid the risk of accidents and damage to the
appliance, please read these instructions carefully
before installation and before using it for the first time.
They contain important notes on installation, safety,
use and maintenance.
Keep these instructions in a safe place and ensure
that new users are familiar with the content. Pass
them on to any future owner.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Correct application
This hob is not designed for commercial use. It is
intended for use in domestic households and in similar
working and residential environments such as:
~
– Shops
– Offices and showrooms
and by residents in establishments such as:
– Hostels and guest houses.
The hob is intended for domestic use only to cook
food and keep it warm.
~
Any other use is not supported by the manufacturer
and could be dangerous. Miele cannot be held liable
for damage resulting from incorrect or improper use or
operation.
The hob is not intended for outdoor use.
~
The hob can only be used by people with reduced
~
physical, sensory or mental capabilities or lack of
experience and knowledge if they are supervised
whilst using it, or have been shown how to use it in a
safe way and understand the hazards involved.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Safety with children
The hob is not a toy! To prevent the risk of injury, do
not let children play with the appliance or its controls.
~
Children under 8 years of age must be kept away
~
from the hob unless they are constantly supervised.
Children 8 years and older may use the hob only if
they have been shown how to use it in a safe way and
understand the hazards involved.
~
The hob gets hot when in use and remains hot for
~
quite a while after being switched off. Keep children
well away from the appliance until it has cooled down
and there is no danger of burning.
Do not store anything which might arouse a child's
~
interest in storage areas above or next to the hob.
Otherwise they could be tempted into climbing onto the
appliance with the risk of burning themselves.
Keep all pans out of reach of children. Turn pan
handles inwards away from the edge of the hob.
Danger of burning or scalding.
~
Packaging, e.g. cling film, polystyrene and plastic
~
wrappings, must be kept out of the reach of babies
and young children. Danger of suffocation. Dispose of
or recycle all packaging safely as soon as possible.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Before installation, check the hob for visible signs of
damage. Do not install and use a damaged appliance.
It could be dangerous.
~
The electrical safety of the hob can only be
~
guaranteed if correctly earthed. It is most important that
this basic safety requirement is observed and regularly
tested, and where there is any doubt, the household
wiring system should be inspected by a qualified
electrician.
Miele cannot be held liable for the consequences of an
inadequate earthing system (e.g. electric shock).
Before connecting the hob to the mains electricity
~
supply, make sure that the data quoted on the data
plate match the household mains supply, otherwise the
appliance could be damaged. Consult a qualified
electrician if in any doubt.
For safety reasons, the hob may only be used after it
~
has been built in.
Do not open the casing of the hob.
~
Tampering with electrical connections or components
and mechanical parts is highly dangerous to the user
and can cause operational faults.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Connection to the gas supply must be carried out by
~
a suitably qualified and competent person in strict
accordance with current local and national safety
regulations, e.g. a Gas Safe registered technician in
the U.K.
The hob may be connected via a fused plug and
switched socket. If you wish to connect it to a fused
spur connection, or of if the appliance is supplied
without a plug, it must be installed and connected to
the electrical supply by a suitably qualified and
competent person is strict accordance with current
local and national safety regulations. Miele cannot be
held liable for damage caused by incorrect installation
or connection.
Installation, maintenance and repairs may only be
~
carried out by a suitably qualified and competent
person in strict accordance with current national and
local safety regulations.
Repairs and other work by unqualified persons could
be dangerous. Miele cannot be held liable for
unauthorised work.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
During installation, maintenance and repair work, the
hob must be disconnected from the gas supply and
mains electricity supply.
~
While the hob is under guarantee, repairs should
only be undertaken by a service technician authorised
by Miele. Otherwise the guarantee is invalidated.
~
Faulty components must only be replaced by
~
genuine Miele original spare parts. The manufacturer
can only guarantee the safety of the appliance when
Miele replacement parts are used.
If the connection cable is damaged, it must be
~
replaced by a suitably qualified electrician with a
special connection cable of type H 05 V V-F (pvc
insulated), available from Miele.
The hob is not intended for use with an external timer
~
switch or a remote control system.
Do not connect the hob to the mains electricity
~
supply by a multi-socket adapter or an extension lead.
These do not guarantee the required safety of the
appliance (e.g. danger of overheating).
Do not use the hob if it is faulty. Switch it off immedi-
ately and disconnect it from the mains electricity supply
and the gas supply. Call the Service Department.
~
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
In areas which may be subject to infestation by
~
cockroaches or other vermin, pay particular attention to
keeping the appliance and its surroundings clean at all
times. Any damage which may be caused by
cockroaches or other vermin will not be covered by the
guarantee.
Correct use
The hob gets hot when in use and remains hot for
quite a while after being switched off. Do not touch it
whilst it could still be hot.
~
If a cooker hood is installed above the hob, ensure
~
that the burners are always covered with a pan when in
use. Otherwise flames could reach the cooker hood,
parts of which could then be damaged or set on fire.
Do not leave the hob unattended whilst it is being
used. Oil and fat are potential fire hazards as they can
ignite if overheated.
~
If oil or fat does catch fire, do not attempt to put out
~
the flames with water. Use a suitable fire blanket,
saucepan lid, damp towel or similar to smother the
flames.
Do not use the hob to heat up the room. Due to the
~
high temperatures radiated, objects near the appliance
could catch fire. The life of the appliance could also be
reduced.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Use heat-resistant pot holders or gloves when using
~
the hob. Ensure that they do not come into contact with
the flames. Do not use large cloths, tea towels or
similar as the ends could touch the flames and catch
fire. Do not let the gloves get damp or wet, as this
causes heat to transfer through the material more
quickly with the risk of scalding or burning yourself.
Do not flambé under a cooker hood. The flames
~
could set the cooker hood on fire.
Do not use the hob as a resting place for anything.
~
When the appliance is switched on either deliberately
or by mistake, or when there is residual heat present,
the article could melt or catch fire.
Where several appliances are installed side by side
Do not place hot pots or pans on the cover strip as this
can damage the seal.
~
Do not cover the hob, e. g. with a hob cover, a cloth
~
or protective foil. The material could catch fire, shatter
or melt if the appliance is switched on by mistake or if it
is still warm.
Do not use plastic or aluminium foil containers.
~
These melt at high temperatures and could catch fire.
Do not heat up unopened tins of food on the hob, as
pressure will build up in the tin, causing it to explode.
This could result in injury and scalding or damage.
~
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Make sure all the components of the gas burners
~
have been correctly assembled before switching on.
Pans must be the correct size for the burner they are
~
used on (see "Suitable pans"). A pan which is too small
will be unstable on the pan support. If the pan diameter
is too large, flames can spread out to the sides and
damage or burn the worktop, wall claddings or
surrounding units and also parts of the hob. Miele
cannot be held liable for this type of damage.
Ensure that the flames from the burner do not spread
~
out beyond the base and up the sides of the pan.
Unless the pan manufacturer states that you can do
~
so, do not use pans with very thin bases on the hob,
and never heat up empty pans as they could get
damaged. This could also damage the appliance.
The pan support supplied must always be used.
~
Pans must not be placed directly on the burner.
Do not store any inflammable objects near the hob.
~
Remove splashes of fat and other food debris from
the surface as soon as possible. These are a fire
hazard.
~
Replace the pan supports carefully to avoid
~
scratching the surface of the hob.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Using the hob will cause a build-up of heat and
~
moisture in the room in which it is installed. Ensure that
the room has sufficient natural or mechanical means of
ventilation, e.g. an extractor.
If the hob is used for very long periods of time
~
additional ventilation of the room may be necessary,
e.g. by opening windows or doors, or running the
extractor on the highest setting.
When using an electrical appliance, e.g. a hand-held
~
food blender, near the hob, ensure that the cable of the
electrical appliance does not come into contact with
the hot hob. The insulation on the cable could become
damaged, giving rise to an electric shock hazard.
Spray canisters, aerosols and other inflammable
substances must not be stored in a drawer under the
hob. Cutlery inserts must be heat-resistant.
~
Always ensure that food is sufficiently cooked or
~
reheated. Some foods may contain micro-organisms
which are only destroyed by thorough cooking at a
sufficiently high temperature for long enough.
Therefore, when cooking or reheating food such as
poultry, it is particularly important that the food is
completely cooked through. If in doubt, select a longer
cooking or reheating time.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Avoid allowing liquids or foods containing salt to spill
~
onto the hob. If salty foods or liquids do get on the hob,
they should be removed as soon as possible to avoid
the risk of corrosion.
If the hob is installed behind a kitchen furniture door,
~
it may only be used with the furniture door open.
Only close the door when the appliance is switched off
and the residual heat indicators have gone out.
If the hob has not been used for a long period of
~
time it should be thoroughly cleaned before it is used
again. It is also advisable to have the appliance tested
for safety.
Miele cannot be held liable for damage caused by
non-compliance with these Warning and Safety
instructions.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Please dispose of it at your local
community waste collection/recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Please stick the extra data plate for the
appliance supplied with this
documentation in the space provided in
the "After sales service, data plate,
guarantee" section of this booklet.
Cleaning for the first time
^ Remove any protective foil and
stickers.
^ Clean all removable parts of the
burners with a solution of warm water
and a little washing-up liquid applied
with a soft sponge. Dry all parts
thoroughly after cleaning and then
reassemble the burners (see
"Cleaning and care").
^ Clean the stainless steel trough with
a damp cloth, and then wipe dry.
Metal components have a protective
coating which may give off a slight
smell when heated up for the first
time.
The smell and any vapours will
dissipate after a short time, and do
not indicate a faulty connection or
appliance.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Rapid ignition system
Switching on, adjusting the
flame and switching off
The appliance is supplied with a rapid
ignition system with the following
features:
The control is used to ignite the burner
and to regulate the strength of the
flame.
– Rapid ignition without pressing und
holding the control
ß The gas supply is turned off
& Strong flame
– Automatic re-ignition
/ Weak flame
Should the flame be extinguished by
a gust of air, the burner will re-ignite
automatically.
If re-ignition is unsuccessful, the gas
supply will be cut off automatically
(see "Safety cut-off").
The burners can only be switched
on by pressing in the appropriate
control and turning it anti-clockwise,
and switched off by turning the
control clockwise.
The following will cause damage to
the appliance:
-
-
-
Switching the burner on without
pressing the control down,
Switching the burner on by
turning the control clockwise,
Switching the burner off by
turning the control
anti-clockwise.
The manufacturer will not accept
liability for any damage resulting
from incorrect operation.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Switching on
Regulating the flame
The burners can be regulated at any
level between the strongest and
weakest flame.
Control the flame so that it does not
spread out beyond the sides of the
pan. As the outer part of the flame is
much hotter than the centre, the tips of
the flames should stay beneath the pan
base. Flame tips which extend beyond
the sides of the pan merely warm up
the air in the room and can also
damage pan handles and increase the
danger of injury.
^ To ignite the burner press the control
knob down and turn it anti-clockwise
to the large flame symbol. The ignitor
will make a clicking sound and ignite
the gas.
Operating a control will automatically
create a spark on every burner. This
is quite normal and does not indicate
a fault.
If the burner does not ignite, turn the
control to off "ß ". Air the room or wait at
least 1 minute before trying again.
Switching off
^ Turn the control clockwise to position
"ß ".
If the burner does not ignite the second
time, turn the control to "ß ", and see
"Problem solving guide".
This stops the flow of gas and the flame
goes out.
When switching on, re-ignition
sometimes occurs (1-2 clicks) if the
flame on the ignition safety device has
gone out briefly, or if the thermal
element is not hot enough, e.g.
following a gust of air.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
In-operation indicator and
Residual heat indicator
When a gas burner is switched on, the
relevant in-operation indicator lights up.
Once it has reached a certain
temperature, the residual heat indicator
also lights up. The in-operation
indicator goes out when the gas burner
is switched off. The residual heat
indicator remains on until the gas
burner is cool enough to touch.
Do not touch or place any heat
sensitive objects on the gas hob
while the residual heat indicator is
still on. Danger of burning and fire.
If the displays are flashing, this shows
there is a fault. See section "Problem
solving guide".
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Suitable pans
– Select pans which are suitable for
the burner they are to be used on. In
general: use larger diameter pans on
the large burners, and smaller
Burner
Min. pan base diameter
in cm
Small burner
Medium burner
Large burner
10
12
14
diameter pans on the small burners.
– Always place pans on the pan
support supplied. Pans must not be
placed directly on the burner.
Max. diameter at top of
pan in cm
– Place pans securely on the pan rest
to minimise the risk of tipping.
Small burner
Medium burner
Large burner
20
22
24
– Refer to the chart above and ensure
that the pan diameter falls within the
minimum and maximum diameters
given for the burner you are using. A
pan which is too small will be
– Do not use pots or pans with legs,
e.g. dutch ovens.
unstable on the pan support. If the
pan base diameter is too large,
flames can spread out to the sides
and damage or burn the worktop,
wall claddings or surrounding units
and also parts of the hob. The
manufacturer cannot be held liable
for this type of damage.
– Remember when purchasing new
pans that manufacturers usually refer
to the diameter at the top of the pan
in their documentation.
– Any heat-resistant pans can be
used.
– Pans with thick bases are preferable
as these distribute heat more evenly.
With thin bases, there is a danger of
food overheating in places. Stir the
food frequently.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy-saving tips
– Use a pan lid whenever possible to
minimise heat loss.
– Cook with as little water as possible.
– Cooking times are greatly reduced
when using a pressure cooker.
– Turn the flame down promptly to a
lower setting when the pan has come
to the boil.
– Wide, shallow pans are preferable to
tall, narrow ones. They will heat up
faster.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety features
Thermo-electric ignition
Safety cut-out
This appliance has a thermo-electric
ignition safety device. If the flame goes
out, for example if food has boiled over
or if there is a sudden draught, and
automatic re-ignition has been
If a burner has been used for an
unusually long period (approx. 4
hours), it will switch off automatically.
To use the burner again, turn the
control clockwise to the "ß " position,
and then switch it back on as normal.
unsuccessful, the supply of gas to the
burner will be cut off.
^ To use the burner again, turn the
control clockwise to the "ß " position,
and then switch it back on as normal.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Miele offer a range of branded cleaning To avoid damaging the surface or
and conditioning agents for your hob.
See "Optional accessories".
your hob, do not use:
– cleaning agents containing soda,
alkalines, ammonia, acids or
chlorides,
,Do not use a steam cleaning
appliance to clean this appliance.
The steam could reach electrical
components and cause a short
circuit.
– cleaning agents containing
descaling agents,
– stain or rust removers,
The appliance should be cleaned after
each use. Let it cool down to room
temperature before cleaning.
– abrasive cleaning agents, e.g.
powder cleaners and cream
cleaners,
To avoid water marks and limescale
deposits use a soft cloth to dry surfaces
that have been cleaned with water.
– solvent-based cleaning agents,
– dishwasher cleaner,
Cooked food which spills over onto the
hot appliance can cause discolouration
of the burner components and the
stainless steel surface. Remove any
soiling immediately.
– grill and oven cleaners,
– glass cleaning agents,
– hard, abrasive brushes or sponges,
e.g. pot scourers, brushes or
sponges which have been previously
used with abrasive cleaning agents,
– sharp pointed objects
(these can damage the seal between
the frame and the worktop
– melamine eraser blocks.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Stainless steel surfaces
Pan supports, control knobs
Clean stainless steel surfaces using an Remove the pan supports. Clean the
E-Cloth or with a solution of warm water pan supports and the control knobs
and a little washing-up liquid applied
with a soft sponge. In the case of
stubborn dried-on soiling, soak first.
Finally, dry with a soft cloth.
with a solution of warm water and a little
washing-up liquid applied with a soft
sponge. Stubborn soiling should be
soaked first.
If necessary, the pad on the back of a
washing-up sponge can be used with
Miele cleaning agent for ceramic and
stainless steel hobs (see "Optional
accessories"). Apply with even
pressure following the direction of the
"grain".
After cleaning dry all surfaces with a
clean cloth.
Do not clean the pan supports in a
dishwasher.
To help prevent re-soiling, we
recommend using Miele stainless steel
conditioning agent after cleaning (see
"Optional accessories").
Apply sparingly with a soft cloth
following the instructions on the
packaging.
Printed surfaces (Flame symbols)
Remove any soiling which comes
into contact with the printed flame
symbols straight away. Soiling,
particularly salty food or liquid and
olive oil, can cause damage if left on
the printed surfaces for a long time.
Do not use the Miele ceramic and
stainless steel hob cleaning agent
on the printed flame symbols. This
would rub off the print.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Burner
Reassemble the burner
Do not clean any parts of the burner
in a dishwasher.
The burner should be dismantled and
then cleaned by hand using a solution
of warm water and a little washing-up
liquid applied with a soft sponge.
Parts of the burner that cannot be
removed should be wiped clean with a
damp cloth only.
The ignitor and ignition safety device
should be very carefully wiped clean
using a well wrung out cloth.
Do not let the ignitor get wet. If it gets
wet it will not spark.
After cleaning the burner it must be
reassembled in the correct order.
After cleaning dry all surfaces with a
clean cloth.
Make sure that the flame slits are clean
and completely dry.
^ Place the burner head o on to the
burner base r so that the ignition
safety device p and the ignitor q
extend through their respective holes
in the burner head. The burner head
must click into place correctly.
The surface of the burner cap will
become more matt with time. This is
quite normal and will not affect the
operation of the hob.
^ Place burner cap n flat over burner
head o.
When correctly positioned it will not
slide about.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
... there has been a power cut.
,Repairs to the gas and electrical
components of this appliance must
only be carried out by a suitably
qualified and competent person to
ensure safety (Gas Safe registered
in the UK). Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
Turn all the controls clockwise to the "ß "
position. You can then operate the
appliance as normal.
If the problem persists, disconnect the
appliance from the electricity supply for
a few seconds.
... the burner does not ignite after
several attempts.
unauthorised work.
Disconnect the appliance from the
electricity supply for a few seconds. If
the problem persists, check whether
What to do if ...
... the burner does not ignite when
the hob is being used for the first
time or after a long period of not
being used.
– the burner is assembled correctly.
– the gas supply tap is turned on.
– the burner is dry and clean.
There could be an air lock in the gas
pipe. You may need to make several
attempts before the burner ignites
successfully.
– the flame slits are dry and
unblocked.
... the gas flame goes out after being
lit.
... the in-operation and residual heat
indicators are flashing at the same
time.
The flames need to touch the ignition
safety device so that it heats up
sufficiently.
– There has been a power cut.
– Re-ignition was not possible.
If the flames do not touch the ignition
safety device, check that
– The gas supply has been
interrupted.
– the burner components are
assembled correctly.
Turn all the controls clockwise to the "ß "
position. You can then operate the
appliance as normal.
– there is no soiling on the ignition
safety device. If there is, remove it
carefully (see "Cleaning and care").
If the problem persists, disconnect the
appliance from the electricity supply for
a few seconds.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
... the gas flame suddenly looks
different.
Check whether the burner components
are assembled correctly.
... the gas flame goes out during
operation.
Check whether the burner components
are assembled correctly.
.... the ignitor on the burner does not
spark.
Check whether
– the mains fuse has tripped. If it has,
contact a qualified electrician or the
Miele Service Department.
– food deposits have lodged
themselves between the ignitor and
the burner cap.
Remove any food deposits carefully
(see "Cleaning and care").
– food deposits have lodged
themselves on the ignition safety
device.
Remove any food deposits carefully
(see "Cleaning and care").
For safety reasons you may not be
able to re-ignite the burner for about
5 minutes after a spillage.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional accessories
Miele offer a comprehensive range of useful accessories as
well as cleaning and conditioning products for your Miele
appliances.
These can be ordered online at:
or from Miele (see back cover for contact details)
Ceramic and stainless steel hob cleaner 250 ml
Removes heavy soiling, limescale deposits and light
discolouration
Stainless steel conditioning agent 250 ml
Removes water marks, flecks and fingerprints.
Helps prevent re-soiling.
E-cloth (microfibre cloth)
Removes fingerprints and light soiling.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Ensure that the gas pipe and
electrical cable are installed in such a
way that they do not touch any parts of
the appliance which become hot. This
could cause damage.
~
This appliance must be installed and
connected to services in
accordance with local and national
safety and building regulations.
The electrical cable and any flexible
~
To avoid the risk of damaging the
hob fit the wall units and extractor
hood before installing it.
gas connection pipe must be installed
in such a way so that they do not come
into contact with any moving kitchen
parts (e.g. a drawer), and cannot
become trapped.
The room in which the gas hob is
~
Observe carefully the safety
distances given on the following pages.
installed must be at least 20 m3 in size
with a door or window in it which can
be opened to the outside air.
~
All dimensions in this instruction booklet
are given in mm.
The veneer or laminate coatings of
~
worktops (or adjacent kitchen units)
must be treated with 100 °C
heat-resistant adhesive which will not
dissolve or distort.
Any backmoulds must be of
heat-resistant material.
This appliance must not be used in
~
a non-stationary location (e.g. on a
ship).
An electric fryer must not be
~
installed directly next to a gas hob, as
the gas flames could ignite the fat in the
fryer. It is essential to maintain a
distance of at least 288 mm between
these two appliances.
A gas hob must not be installed
~
above a fridge, fridge freezer, freezer,
dishwasher, washing machine or
tumble dryer.
The hob may only be installed
~
above a Miele oven if the worktop is at
least 40 mm thick.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distance above the appliance
A minimum safety distance must be
maintained between the appliance and
the cooker hood above it. See the
cooker hood manufacturer's operating
and installation instructions for details.
If the manufacturer's instructions are
not available for the cooker hood, a
minimum safety distance of at least
760 mm must be maintained. For any
flammable objects, e.g. utensil rails,
wall units etc. a minimum distance of at
least 760 mm must be maintained
between them and the appliance
below.
When two or more appliances are
installed together below a cooker hood,
e.g. an electric hob and a gas wok
combiset, which have different safety
distances given in their installation
instructions you should select the
greater distance of the two.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distances to the sides of the
hob
Ideally the hob should be installed with
plenty of space on either side. There
may be a wall at the rear and a tall unit
or wall at one side. On the other side,
however, no unit or divider should
stand higher than the hob (see
illustrations).
Due to the high temperatures radiated
by the appliance, it is essential that a
minimum distance of 50 mm is
maintained between the worktop
cut-out and the back wall.
Recommended
The following minimum distance a
between the worktop cut-out and a wall
or tall unit to the right or left of it must
be maintained:
40 mm for CS 1212 / CS 1212-1
CS 1221 / CS 1221-1
CS 1222
Not recommended
CS 1223
CS 1234 / CS 1234-1
50 mm for CS 1112
CS 1122
CS 1134
CS 1326
CS 1327
CS 1411
100 mm for CS 1012 / CS 1012-1
150 mm for CS 1421
CS 1312
CS 1322
Not allowed
200 mm for CS 1034 / CS 1034-1
250 mm for CS 1011
CS 1021
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distance when installing the appliance near a wall with additional
niche cladding
A minimum safety distance must be maintained between the worktop cut-out and
any niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e. g. wood) a
minimum safety distance e of 50 mm must be maintained between the cut-out
and the cladding.
If the niche cladding is made from a non-combustible material (e. g. metal,
natural stone, ceramic tiles) a minimum safety distance e of 50 mm less the
thickness of the cladding must be maintained between the cut-out and the
cladding.
Example: 15 mm niche cladding
50 mm - 15 mm = minimum safety distance of 35 mm
aMasonry
bNiche cladding
Dimension x = thickness of niche cladding material
cWorktop
dWorktop cut-out
eMinimum safety distance
for combustible materials is 50 mm
for non-combustible materials is 50 mm less dimension x
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance and building-in dimensions
CS 1012-1
aSpring clamps
bFront
cCasing depth
d Casing depth including the mains connection box with mains connection
cable,
L = 1440 mm
eCasing depth including the gas connection R 1/2 - ISO 7-1 (DIN EN 10226)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance and building-in dimensions
CS 1034-1
aSpring clamps
bFront
cCasing depth
dCasing depth including the mains connection box with mains connection cable,
L = 1440 mm
eCasing depth including the gas connection R 1/2 - ISO 7-1 (DIN EN 10226)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the worktop
^ Make the worktop cut-out for one or
more appliances in accordance with
the building-in diagrams.
Remember to maintain the minimum
safety distance from the back wall,
as well as from any tall unit or side
wall to the right or left of the hob.
See "Safety instructions for
installation".
^ Seal the cut surfaces with a suitable
heat-resistant sealant to avoid
swelling caused by moisture.
If, during installation, you find that the
seals on the corners of the frame are
not flush with the worktop surface,
the corner radius (ß R4) can be
carefully scribed to fit.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation of several appliances
When installing two or more appliances next to each other a spacer bar b must
be used between each one.
See "Fixing the spring clamps and spacer bars".
Worktop cut-out
- two appliances
Worktop cut-out
- three appliances
To calculate the cut-out width (D) required:
Add up the widths of each appliance (e.g. 288 mm, 380 mm) and subtract 16 mm
from this figure
Number of
appliances
Appliance width in mm Worktop cut-out in mm
1
2
2
3
3
288
288 - 16 = 272
288, 288
288 + 288 - 16 = 560
288 + 380 - 16 = 652
288 + 288 + 288 - 16 = 848
288 + 288 + 380 - 16 = 940
288, 380
288, 288, 288
288, 288, 380
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation of several appliances
aSpring clamps
bSpacer bars
cGaps between spacer bars and worktop
dCover strips
The illustration shows a worktop cut-out with spring clamps a and spacer bars b
for 3 appliances.
An additional spacer bar is required for each additional appliance. The position
for securing each additional spacer bar will depend on the width of appliance B
(288 mm / 380 mm / 576 mm).
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Fixing the spring clamps and spacer bars
Wooden worktops
^ Position the spring clamps supplied
a and spacer bars b on the top
edge of the cut-out in the positions
marked.
^ Secure the spring clamps and
spacer bars with the 3.5 x 25 mm
screws supplied.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Fixing the spring clamps and spacer bars
Granite and marble worktops
The screws are not required for
granite or marble worktops.
^ Apply silcone to the side edges and
the lower edges of spring clamps a
and spacer bars b.
^ Then fill gap e between the spacer
bars and the worktop with silicone.
^ Position and secure the spring
clamps a and spacer bars b using
strong, double-sided adhesive tape
c.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing / removing the appliance
Installing the appliance
^ Starting at the front, position the next
appliance in the worktop cut-out.
^ Feed the connection cable down
through the cut-out.
^ Connect the appliance(s) to the
mains (see "Electrical connection")
and to the gas supply (see "Gas
connection").
^ Starting at the front, position the
appliance in the worktop cut-out.
^ Using both hands, press down
evenly on the sides of the appliance
until it clicks into position. When
doing this make sure that the seal
under the appliance sits flush with
the worktop on all sides. This is
important to ensure an effective seal
all round. Do not use sealant.
^ Check that the appliance(s) work(s).
Removing the appliance
If the appliance is accessible
underneath, it can be pushed up out of
the cut-out from below. It must be
pushed up from the back first.
^ Push the appliance to the side until
the holes in the spacer bar can be
seen.
If the appliance is not accessible
underneath, take hold of the appliance
with both hands at the back, pull it
forwards, then lift it up and out.
^ Fit the cover strip d into the holes in
the spacer bar b.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
General installation tips
Seal between the appliance and the
worktop
Tiled worktop
Grout lines a and the hatched area
underneath the surface of the
appliance must be smooth and even. If
they are not, the appliance will not sit
flush with the worktop and the sealing
strip underneath the top part of the
appliance will not provide a good seal
between the appliance and the
worktop.
The sealing strip under the edge of the
top part of the appliance provides a
sufficient seal for the worktop.
The appliance must not be sealed
with sealant (e.g. silicone).
This could result in damage to the
appliance or the worktop if it ever
needs to be removed for servicing.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Connection should be made via a fused
plug and switched socket or a double
pole fused spur connection unit, or a
suitable isolator (as appropriate) which
complies with national and local safety
regulations and the on/off switch should
be easily accessible after the appliance
has been built in.
All electrical work should be carried
out by a suitably qualified and
competent person in strict
accordance with current local and
national safety regulations (BS 7671
in the UK).
If the connection cable is damaged,
it must be replaced by a suitably
qualified electrician with a special
connection cable of type H 05 V V-F
(pvc insulated), available from Miele.
If the switch is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD).
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
When switched off there must be an
all-pole contact gap of at least 3 mm in
the isolator switch (including switch,
fuses and relays).
unauthorised work.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Important U.K.
The appliance is supplied for
connection to a 230-240 V, 50 Hz
supply with a 3-core cable.
The appliance must only be
operated when built-in. This is to
ensure that all electrical parts are
shielded. Live parts must not be
exposed.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
Blue
= neutral
= live
Brown
WARNING
THIS APPLIANCE MUST BE
EARTHED
Please make sure that the connection
data quoted on the data plate match
the household mains supply.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Important
The electrical safety of this appliance
can only be guaranteed when
continuity is complete between it and
an effective earthing system, which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested and where
there is any doubt, the electrical wiring
in the home should be tested by a
qualified electrician. The manufacturer
cannot be held liable for the
consequences of an inadequate
earthing system such as an electric
shock.
The manufacturer cannot be held
liable for damage which is the direct
or indirect result of incorrect
installation or connection.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas connection
Depending on country, the hob is
,Connection to the gas supply, or
conversion from one type of gas to
another, should only be undertaken
by an approved and registered gas
installer in strict accordance with
local and national safety and
supplied ready for connection to natural
or liquid gas (refer to label on the
appliance).
United Kingdom:
GB II 2 H 3+ 20 mbar, 28-30/37 mbar
Ireland:
IE II 2 H 3+ 20 mbar, 28-30/37 mbar
building regulations (e.g. Gas Safe
registered in the UK).
Depending on country, a set of jets for
conversion to an alternative type of gas
may be included with the hob.
Every appliance should have its own
easily accessible isolating valve and
test point.
Please contact your dealer or the Miele
Spare Parts Department for the
appropriate conversion jets if
necessary.
Check with your local gas supplier
about the type of gas and its
calorific value and compare this
information with the type of gas
quoted on the hob data plate.
Conversion to another type of gas is
described under "Conversion to another
type of gas".
This appliance is not connected to
an exhaust flue. Please ensure it has
adequate ventilation after
installation.
For any gas work in the UK always
use a Gas Safe registered engineer.
The installer is responsible for
ensuring that the appliance
functions correctly when installed.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas connection
Connection
The gas connection must be installed
so that connection can be made either
from inside or outside the kitchen unit,
and the isolating valve must be easily
accessible and visible (by opening one
of the kitchen doors, if necessary).
After installing the appliance the gas
burners have to be set for local
conditions.
When the gas hob has been installed, it
is essential to check that neither the
gas pipe not the electricity cable is in
contact with hot parts of the appliance
or hot gas exhaust, otherwise heat
damage to the pipe and cable could
occur.
aConnection with test point
specifically for GB
bConnection with test point
specifically for GB and 90° angle
A test for possible leakages must be
carried out after installation.
Safety regulations demand that a
pressure test point is installed near a
gas hob to allow an engineer to test the
pressure, following servicing.
The appliance is supplied with an
R 1/2" - ISO 7-1 (DIN EN 10226) gas
connection point.
An appropriate rigid connection and
isolating valve must be installed for final
connection.
The gas connection must be so sited
that it is not adversely heated when the
appliance is in operation.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
Screw in the new jets according to the
following table.
,Connection to the gas supply, or
conversion from one type of gas to
another, should only be undertaken
by an approved and registered gas
installer in strict accordance with
local and national safety and
Jet table
For UK and IE
building regulations (e.g. Gas Safe
registered in the UK).
Main jet
C
Small jet
C
When converting to a different type of
gas, the main jets and the small jets
have to be changed.
Natural gas H
Medium burner
Large burner
1.00
1.28
0.42
0.52
Liquid gas
Medium burner
Large burner
0.67
0.87
0.27
0.32
CS 1012-1
Nominal rating at high setting
The jet markings refer to 1/100 mm of
the jet diameter.
Gas type
kW
Medium
burner
Natural gas H
Liquid gas
1.80
1.80 / 131 g/h
Large
burner
Natural gas H
Liquid gas
3.00
3.00 / 218 g/h
Total output Natural gas H
Liquid gas
4.80
4.80 / 349 g/h
Nominal rating at low setting
Gas type
kW
Medium
burner
Natural gas H
Liquid gas
0.35
0.35
Large
burner
Natural gas H
Liquid gas
0.50
0.50
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
CS 1034-1
Screw in the new jets according to the
following table.
Nominal rating at high setting
Jet table
Gas type
kW
Small burner Natural gas H
Liquid gas
1.00
1.00 / 73 g/h
For UK and IE
Main jet
C
Small jet
C
Medium
burner
Natural gas H
Liquid gas
1.80
1.80 / 131 g/h
Natural gas H
Small burner
Medium burner
Large burner
Large burner Natural gas H
Liquid gas
3.00
3.00 / 218 g/h
0.76
1.00
1.28
0.39
0.42
0.52
Total output
Natural gas H
Liquid gas
8.80
8.80 / 640 g/h
Liquid gas
0.50
0.67
0.87
0.23
0.27
0.32
Small burner
Medium burner
Large burner
Nominal rating at low setting
Gas type
kW
The jet markings refer to 1/100 mm of
the jet diameter.
Small burner
Medium burner
Large burner
Natural gas H
Liquid gas
0.25
0.25
Natural gas H
Liquid gas
0.35
0.35
Natural gas H
Liquid gas
0.50
0.50
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
Changing the jets
Disconnect the gas hob from the
mains electricity supply. Turn off the
gas supply.
To change the main jets
^ Carefully remove the upper section of
the appliance. When doing this make
sure you do not also pull out the light
unit for the display a located
underneath the upper section. To
release the unit, squeeze together
the two clamps b.
^ Remove the pan support, burner cap
n and burner head o.
^ Using an M7 socket spanner,
unscrew main jet s.
^ Change the main jet.
^ Using a small screwdriver, unscrew
small jet u in the gas fitting.
To change the small jets
The upper section of the appliance has
to be removed before the small jets can
be changed.
^ Pull out the jet with a pair of pliers.
^ Fit the correct jets securely (see jet
table).
^ Remove burner cap n and burner
head o.
^ Finally, secure the jets against
inadvertent loosening with sealing
wax.
^ Pull the control knobs off.
^ Loosen screws t.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
Function test
Check all gas fittings for leaks.
^ Reassemble the appliance.
^ Check the burner flame by operating
the burner.
The flame must not go out on the
lowest setting, or when the control is
turned quickly from a high to a low
setting.
On the highest setting, the flame
must have a distinctive and visible
core.
^ Stick the label supplied with the jets
above the label stating the type of
gas being used.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service, data plate, guarantee
In the event of any faults which you cannot remedy yourself, or if the appliance is
under guarantee, please contact:
– Your Miele dealer, or
– the Miele Service Department (see back cover for address).
Please note that telephone calls may be monitored and recorded to improve
our service.
When contacting Miele, please quote the model and serial number of your
appliance which are given on the data plate.
N.B. A call-out charge will be applied for service visits where the problem
could have been resolved as described in these instructions.
Space in which to stick the extra data plate supplied with the appliance. Ensure
that the model number is the same as the one on the front of these instructions.
Guarantee
For information on the appliance guarantee specific to your country please
contact Miele. See back cover for contact details.
In the U.K. your appliance is guaranteed for 2 years from the date of purchase.
However, you must activate your cover by calling 0845 365 6640 or registering
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved/ 4111
M.-Nr. 09 094 640 / 01
Download from Www.Somanuals.com. All Manuals Search And Download.
|