OPERATORS AND PARTS MANUAL NO. 07-1-8720/8865
INDUSTRIAL SERIES
TWIN EXPELLER SUPER SPREADER
MODEL 8720
MODEL 8865
PATENTED
U.S. PATENT NUMBER
5,368,236
5,501,404
8865 SPREADER
8720 SPREADER
DO NOT OPERATE EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD
MANUFACTURED BY
County Hwy. A West
P.O. Box 405
Dorchester, Wisconsin 54425-0405
Phone 715-654-5132 • FAX 715-654-5513
1-800-325-9103
E-mail: [email protected]
12/06
Download from Www.Somanuals.com. All Manuals Search And Download.
July 1, 2000
NEW MEYER INDUSTRIAL SPREADER
MANUFACTURER’S WARRANTY
I.
The “Product Registration & Inspection Certificate” along with the original billing invoice “Owners Registration Form”
must be completed in full and promptly returned to Meyer Mfg. Corp. for this warranty to become both valid and
effective. All warranties on New Meyer Super Spreaders shall apply only to the original retail customer from an
authorized Meyer Mfg. Corp. dealership.
II.
This warranty shall not apply to any Meyer Super Spreader which has been subjected to misuse, negligence,
alteration, accident, incorrect operating procedures, or which shall have been repaired with parts other than
those obtained through Meyer Mfg. Corp.
III.
Meyer Mfg. Corp. warrants New Meyer Super Spreaders to be free from defects in material and workmanship under
recommended use and maintenance service, as stated in the Operator’s and Parts Manual," as follows:
A.
B.
Meyer Mfg. Corp. will repair or replace F.O.B. Dorchester, WI, as Meyer Mfg. Corp. elects, any part of a new
Meyer Super Spreader which is defective in material or workmanship:
1. Without charge for either parts or labor during the first (1) year from purchase date to the
original retail customer.
In addition to the above basic warranty, Meyer Mfg. Corp. will repair or replace F.O. B. Dorchester, WI as Meyer
Mfg. Corp. elects:
Ten (10) Years: After a period of (1) year, the spreader tank body is warranted against rust-through for an
additional period of (9) years. (Pro-Rated Parts Only). Parts included, front and rear end
panels, side panels, and auger trough.
IV.
V.
COMMERCIAL USE: Coverage as in paragraph III A1 ONLY, except warranty coverage is for (90) days for parts and
labor to the original commercial retail customer.
Repairs eligible for labor warranty must be made by Meyer Mfg. Corp. or an authorized Meyer dealership. The
original retail customer is responsible for the transportation of the super spreader to the dealership for warranty
service or for any service call expenses.
VI.
Except as stated above, Meyer Mfg. Corp. shall not be liable for injuries or damages of any kind or nature, direct,
consequential, or contingent, to persons or property. This warranty does not extend to loss of crop or for any other
reasons.
VII.
No person is authorized to give any other warranties or to assume any other obligation on Meyer Mfg. Corp.’s. behalf
unless made or assumed in writing by Meyer Mfg. Corp. This warranty is the sole and exclusive warranty which is
applicable in connection with the manufacture and sale of this product and Meyer Mfg. Corp.’s responsibility is
limited accordingly.
VIII.
This warranty is effective on all sales of Meyer Super Spreaders made after January 1, 1992.
Model 8720/8865
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Congratulations on your purchase of a new Meyer farm
This supersedes all previous published instructions.
equipment product. Undoubtedly you have given much
consideration to your purchase and we’re proud that you
have selected Meyer. Pride in craftsmanship, engineer-
ing and customer service have made Meyer products
the finest in the farm equipment industry today.
IMPORTANT:
At the front of this manual is a Product Registration and
Inspection Certificate. Be sure your dealer has com-
pleted this certificate and promptly forwarded a copy to
Meyer Mfg. to validate the manufacturer’s warranty. The
product model and serial number are recorded on this
certificate and below for proper identification of your
Meyer Industrial Spreader by your dealer and the manu-
facturer when ordering repair parts. The serial number
plate is found on the upper left front corner of the
spreader tank or stamped in the left front frame channel.
There is no substitute for quality. That is why thousands
of people like you have purchased Meyer farm equip-
ment. They felt it was the best equipment to serve their
farming needs, now and in years to come. We ask that
you follow our policy of “safety first,” and we strongly
suggest that you read through the owner’s manual be-
fore operating your Meyer farm equipment.
Model No.
Serial No.
_____________________________
_____________________________
Meyer Manufacturing Corporation wants to thank you
for not compromising quality. We are determined to offer
excellence in customer service as well as provide you
with the very best value for your dollar.
Date of Purchase
______________________
REMEMBER:
At the back of this manual is the repair parts section. All
replacement parts are to be obtained from or ordered
through your Meyer dealership. When ordering repair
parts, refer to the parts section and give complete infor-
mation including quantity, correct part number, detailed
description and even Model No. and Serial No. of the
Meyer Industrial Spreader which needs repair parts.
FARM EQUIPMENT BUYERS
TRUST THE NAME MEYER!
Sincerely,
All Employees of
MEYER MANUFACTURING CORPORATION
NOTE: All references to right hand (RH), left hand (LH),
front and rear apply to the product as viewed from the
rear of the spreader.
Meyer Mfg. Corp. reserves the right to make improve-
ments in design, or changes in specifications at any
time, without incurring any obligation to owners of units
previously sold.
Model 8720/8865
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
This symbol is used to call attention to instructions concerning personal safety. Be sure to observe
and follow these instructions. Take time to be careful!
WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY THE
FOLLOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO
OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR
WITH THESE SAFETY PRECAUTIONS.
Require anyone who will operate this spreader to read and completely understand this Owner’s Manual. Give
necessary instructions!
DO NOT operate, service, inspect or otherwise handle this spreader until all operators have read this Owner’s
Manual and have been properly trained in the intended usage of the spreader.
Do not allow minors (children) or inexperienced persons to operate this spreader.
If the spreader becomes clogged, shut off the tractor engine and allow all mechanisms to stop. Disconnect PTO shaft
and hydraulic hoses (relieve hydraulic pressure). Then, clean or work on the spreader as required.
Always shut off power and disconnect PTO drive shaft and unhook hydraulic hoses (relieve hydraulic pressure) from
tractor to prevent accidental startup or unexpected movement before working on machine.
Do not clean, adjust, or lubricate while spreader is in motion.
Make sure all hydraulic fittings are tight and that all hoses are in good condition. Hydraulic fluid escaping under
pressure can have sufficient force to penetrate skin and cause serious injury. Never investigate for hydraulic leaks by
using a part of the body to feel for escaping fluid.
Inspect when first delivered and regularly thereafter; that all connections and bolts are tight and secure before operating.
Know how to stop the spreader before starting it!
Do not operate until all shields, covers, and guards are in place.
Make certain everyone is clear of the spreader before applying power.
Keep hands, feet and clothing away from moving parts. Loose or floppy clothing should not be worn by the operator.
Stay well clear of the spreader’s rear discharge spinners while operating.
Do not step up on any part of the spreader at any time. Do not use PTO guard as a step.
Do not step over the power take-off shaft. Stay clear of the PTO at all times.
Keep PTO shaft telescoping tube shields turning freely. Keep PTO master shield on tractor. Replace shields missing
or damaged.
Never operate PTO above normal 1000 RPM rating. Tractors PTO MUST match implement PTO.
Use only properly rated tires.
Do not tow at speeds in excess of 20 MPH when transporting this spreader. Never exceed a safe travel speed.
Observe all applicable traffic laws when transporting on public roadways (where legal to do so). Check local laws for
all highway lighting and marking requirements.
Always install a SMV emblem on this spreader for transporting on roadways and keep the emblem clean and bright.
When towing the spreader on public roads a safety chain of sufficient strength to support, along the line of travel,
the gross weight of the spreader must be used (See Maximum Load Weight Chart in the Transporting Section). The
safety chain should be attached per diagram in the Transporting Section.
MEYER MFG. CORP. PROVIDES GUARDS FOR EXPOSED MOVING PARTS FOR THE OPERATOR’S
PROTECTION; HOWEVER, SOME AREAS CANNOT BE GUARDED OR SHIELDED IN ORDER TO ASSURE
PROPER OPERATION. THE OPERATOR’S MANUAL AND DECALS ON THE MACHINE ITSELF WARN YOU
OF DANGERS AND MUST BE READ AND OBSERVED CLOSELY.
STUDY THE ABOVE SAFETY RULES
FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Model 8720/8865
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
A brief definition of signal words that may be used in this
manual is as follows:
situation which, if not avoided, COULD result in death or
serious injury, and includes hazards that are exposed
when guards are removed.
DANGER indicates an imminently hazardous sit-
uation which, if not avoided, WILL result in serious injury
or death.
CAUTION indicates a potentially hazardous
situation which, if not avoided, MAY result in minor or
moderate injury. It is also used to alert against unsafe
practices.
WARNING indicates a potentially hazardous
A
A
B,N
Located
Under Shield
K
E
M
E
I
J
C
D
E
B,N
Located
Under Shield
G
C
A
A
F
A
F
B,L,N
Located
Under
Shield
C
H
Both Sides
Both Sides
CAUTION: READ ALL DECALS ON THE SPREADER AND IN THIS MANUAL. KEEP THESE DECALS CLEAN AND
REPLACE ANY LOST OR DESTROYED DECALS. BECOME FAMILIAR WITH ALL TRACTOR AND SPREADER CONTROLS.
Model 8720/8865
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
The Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader are vari-
ous decals to aid in operation and warn of danger or caution areas. Pay close attention to all decals on the spreader.
DO NOT REMOVE ANY DECALS. IF DECALS ARE LOST, DAMAGED OR IF MANURE SPREADER IS
REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMA-
TION.
DECAL C. PART NO. 46-3600-9
DECAL B. PART NO. 46-0001-26
DECAL A. PART NO. 46-0001-5
DECAL E. PART NO. 46-0001-4
DECAL D. PART NO. 46-3600-6
DECAL H. PART NO.
DECAL G. PART NO. 46-0001-13
46-3600-8
DECAL F. PART NO. 46-3600-1
DECAL I. PART NO. 46-0001-22
DECAL K. PART NO. 46-0001-35
DECAL J. PART NO. 46-0004-2
DECAL L. PART NO. 46-5570-3
Decal M. Part No. 46-8500-7
Decal N. Part No. 46-3600-7
CAUTION: READ ALL DECALS ON THE SPREADER AND IN THIS MANUAL. KEEP THESE DECALS CLEAN AND
REPLACE ANY LOST OR DESTROYED DECALS. BECOME FAMILIAR WITH ALL TRACTOR AND SPREADER CONTROLS.
Model 8720/8865
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-OPERATION
WARNING: BEFORE OPERATING, READ THIS OWNERS MANUAL COMPLETELY. PAY
PARTICULAR ATTENTION TO THE “SAFETY PRECAUTION” AND “SAFETY FIRST” PAGES. READ ALL
SAFETY MESSAGES HIGHLIGHTED BY “SAFETY ALERT SYMBOLS” THROUGHOUT THE MANUAL.
This spreader must be operated with a 1000 RPM PTO.
The hitch of the spreader is designed for a standard
tractor drawbar. Adjust the drawbar at 15 to 22 inches
above the ground. Extend or shorten the drawbar so
horizontal distance from end of tractor PTO shaft to cen-
ter of the hitch pin hole is 20” (1 3/4-20), 16” (1 3/8-21).
Secure the drawbar so that the hitch pin hole is located
tion of standard measurements.
WARNING: INSPECT REGULARLY THAT ALL
CONNECTIONS AND BOLTS ARE TIGHT AND SE-
CURE BEFORE OPERATING. FAILURE TO HEED MAY
RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Check for proper assembly and adjustment and make
sure that all bolts are tightened. Securely retighten after
a few hours of operation, as bolts can loosen up on new
machinery. Check wheel lug nuts upon delivery and pe-
riodically thereafter. Lug nuts should be tightened at
250-265 ft./lbs. of torque. Check the tires and inflate to
the recommended pressure. See chart on page 60.
Inspect all adjustments on the spreader to be sure they
are proper and to provide maximum performance. Lubri-
cate the spreader completely if it is required and check
the level of oil in the right rear corner gear box, and the
gear grease in the expeller gear boxes.
An improperly located hitch point may cause damage to
the universal joints of the PTO drive shaft. Conforming
to the standard 16" or 20” drawbar & PTO relationship
will ensure that the PTO drive shaft will not become
over-extended.
WARNING: DO NOT OPERATE WITHOUT
ALL SHIELDS, GUARDS AND COVERS INSTALLED.
FAILURE TO HEED MAY RESULT IN SERIOUS PER-
SONAL INJURY OR DEATH.
Fasten the spreader hitch to the tractor drawbar with a
hitch pin that cannot bounce out. Use a 1-5/16” to 1-3/8”
diameter hitch pin to pull spreader.
Remove the weight from the jack (jack is not to be used
when spreader is loaded). Remove the jack from round
mount tube and move to the transport storage tube on
the front of the spreader drive enclosure. Store in a hori-
zontal position.
FIGURE 1. TRACTOR DRAWBAR & PTO
SPECIFICATION
WITH INITIAL HOOK-UP TO YOUR NEW MEYER
SPREADER TEST PTO TRAVEL BY TURNING
EQUIPMENT IN BOTH DIRECTIONS OBSERVING
THE MINIMUM AND MAXIMUM TRAVEL DIMEN-
SIONS AS SHOWN PER DRAWING ON FIGURE 5,
PAGE 15.
Before operation and after hitching the tractor to the
spreader, connect the PTO drive shaft to the tractor.
Slide spring loaded locking collar on PTO yoke rearward,
and slide yoke onto the tractor PTO shaft. Release spring
loaded collar. Be sure pins fall into groove of tractor PTO
shaft and collar snaps forward into locking position.
DANGER: DO NOT OPERATE WITHOUT PTO
GUARD ON SPREADER AND ON TRACTOR. MAIN-
TAIN PTO DRIVE SHAFT GUARD TUBES IN OPER-
ATING CONDITION. REPLACE THEM IF DAMAGED
AND NOT TURNING FREELY. FAILURE TO HEED
MAY RESULT IN SERIOUS PERSONAL INJURY OR
DEATH.
CAUTION: DO NOT USE A STEEL HAMMER
TO AID IN JOINING PTO PARTS.
Route hydraulic hoses through the hose support rod
the hydraulic hoses for the flow control rear gate to the
tractor’s double acting valve hydraulic system. Move the
tractor hydraulic controls to observe proper flow gate
Model 8720/8865
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
operation. If the controls operate the gate in opposite di-
rections to what you expect, reverse the hydraulic hose
connections at the tractor.
HOSE
BRACKET
WARNING: HYDRAULIC FLUID ESCAPING
UNDER PRESSURE CAN HAVE SUFFICIENT
FORCE TO PENETRATE SKIN. KEEP ALL HOSES
AND CONNECTIONS IN GOOD SERVICEABLE CON-
DITION. FAILURE TO HEED MAY RESULT IN SERI-
OUS PERSONAL INJURY OR DEATH.
PTO
SHAFT
Before loading spreader, slowly engage the tractor PTO
and operate machine at idle speed for several minutes
to insure the spreader is lubricated and operating prop-
erly.
JACK STORAGE
HUB
JACK
TRANSPORTING
HITCH
TRACTOR TOWING SIZE REQUIREMENTS
Use the following chart for calculating the minimum trac-
tor weight.
FIGURE 2. SPREADER HOOKUP
MODEL SPREADER EMPTY
WEIGHT + LOAD = GW
MINIMUM
NOTE: HEAPED LOADS HAVE SIGNIFICANTLY
HIGHER CAPACITIES
TRACTOR
WEIGHT UP TO
20 MPH
SV2636 6,100 + _____ = _____
SV3245 7,640 + _____ = _____
SV3954 8,650 + _____ = _____
2/3 of spreader
gross weight
Check that the flow control rear gate is completely
closed. It is unlawful to allow slurry to splash or leak onto
public roads.
2/3 of spreader
gross weight
2/3 of spreader
gross weight
WARNING: DO NOT TOW AT SPEEDS
GREATER THAN 20 MPH. FAILURE TO HEED MAY
RESULT IN SERIOUS PERSONAL INJURY OR
DEATH.
SI8720
SI8865
11,445 + _____ = _____
18,140 + _____ = _____
2/3 of spreader
gross weight
2/3 of spreader
gross weight
Operating speed is dictated by the terrain over which
you are traveling. Always use caution. Avoid traveling
on slopes or hills that are unsafe.
MATERIAL ESTIMATED WEIGHT PER CUBIC FOOT
MATERIAL
LBS / CU. FT.
110-115 LBS.
63-65 LBS.
63-65 LBS.
62-65 LBS.
58-60 LBS.
30-35 LBS.
63-65 LBS.
LIME SLUDGE
DRY FEEDLOT MANURE
CHICKEN LITTER
CAKE SLUDGE
WARNING: OBSERVE ALL APPLICABLE
TRAFFIC LAWS WHEN TRANSPORTING ON PUB-
LIC ROADWAYS. CHECK LOCAL LAWS FOR ALL
HIGHWAY LIGHTING AND MARKING REQUIRE-
MENTS.
SEMI-SOLID MANURE
PEN PACKED MANURE
LIQUID MANURE
SOURCE: ASAE
MAXIMUM SPREADER LOAD WEIGHTS
2636 3245T
12,000 24,000 32,000 46,645
Model
3954T
8720T
8865T
56,140
18,140
562
Maximum Gross Weight (Pounds)
Total Net Weight (Pounds)
Cubic Foot Capacity**
Capacity in Gallons
6,100
181
7,640
227
8,650
272
11,445
468
1,355
1,694
2,033
3,500
4,200
**Struck capacity, heaped loads have significantly higher capacities
Model 8720/8865
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: OBSERVE ALL APPLICABLE
TRAFFIC LAWS WHEN TRANSPORTING ON PUB-
LIC ROADWAYS. CHECK LOCAL LAWS FOR ALL
HIGHWAY LIGHTING AND MARKING REQUIRE-
MENTS.
CAUTION: A SAFETY CHAIN MUST BE IN-
STALLED TO RETAIN THE CONNECTION BE-
TWEEN TRACTOR (OR OTHER TOWING VEHICLE)
AND SPREADER WHENEVER TRAVELING ON
PUBLIC ROADS IN CASE THE HITCH CONNEC-
TION WOULD SEPARATE. A SUGGESTED AT-
WARNING: INSTALL A SMV EMBLEM ON
REAR OF SPREADER FOR TRANSPORTING ON
ROADWAYS AND KEEP THIS EMBLEM CLEAN AND
BRIGHT. FAILURE TO HEED MAY RESULT IN SERI-
OUS PERSONAL INJURY OR DEATH.
The chain must be strong enough to hold the weight of
grab hook at the end(s) of the chain to secure the chain
to itself, a hook latch must be installed.
The length of the safety chain is not to be any longer
than necessary to turn without interference. If any chain
links or attachment hardware are broken or stretched,
repair before using. Store chain so it does not corrode or
become damaged. Do not use this chain for other
implements because the strength and length of the
chain may not be adequate. Identify this chain for use on
this particular spreader. Do not use the intermediate
support as the attaching point.
If you will travel on public roads and it is legal to do so,
you must know all rules governing such operation. This
will include lighting and brake requirements in addition
to traffic rules. You may also be required to install a
safety chain device on the spreader.
Check for traffic constantly. Be sure you can see that no
one is attempting to pass you and that all traffic is suffi-
ciently clear from you before making any turns.
OPTIONAL TRUCK MOUNT SPREADERS
Depending on the make and model of the truck it may be
necessary to install a light converter (MEYER PART
#56-0028). Converter will allow signal lights and brake
lights to operate according to DOT lighting standard.
Call factory for more information.
USE OF SAFETY CHAIN
TOWING MACHINE
ATTACHING POINT
SAFETY CHAIN
LOOP.
INTERMEDIATE SUPPORT
HOOK W/ HOOK
LATCH
FIGURE 3. SAFETY CHAIN INSTALLATION
Model 8720/8865
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
FREEZING WEATHER OPERATION
Allow spreader to completely empty last of manure con-
tents and disengage tractor PTO. Shut off tractor, re-
move the ignition key and allow all movement to stop
before attempting to clean the spreader.
WARNING: DO NOT CLEAN, ADJUST OR
LUBRICATE WHILE SPREADER IS IN MOTION.
FAILURE TO HEED MAY RESULT IN SERIOUS PER-
SONAL INJURY OR DEATH.
Scrape clean any remaining manure from inside the rear
of spreader. Clean all manure from ends of augers, flow
control rear gate and spinners.
WARNING: MAKE CERTAIN EVERYONE IS
CLEAR OF THE SPREADER BEFORE APPLYING
POWER. FAILURE TO HEED MAY RESULT IN SERI-
OUS PERSONAL INJURY OR DEATH.
Slowly engage the PTO. Operate the spreader several
minutes to clean manure scrapings and to allow any re-
maining manure and the spreader to freeze dry. Hydrau-
lically run the flow control rear gate up and down to
clean gate slide guides. Park spreader with flow control
rear gate approximately halfway open.
Before loading in freezing weather, make sure augers
and spinners are free to rotate, and the flow control rear
gate moves freely up and down.
DANGER: KEEP AWAY AND KEEP
OTHERS CLEAR OF ROTATING SPINNERS AT
REAR OF SPREADER. SERIOUS INJURY OR AM-
PUTATION COULD RESULT. FAILURE TO HEED
MAY RESULT IN PERSONAL INJURY OR DEATH.
Model 8720/8865
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LOADING
UNLOADING
CAUTION: TO PREVENT DAMAGE TO AU-
WARNING: MAKE CERTAIN EVERYONE IS
GERS, SPINNERS, AND DRIVE LINES, FOREIGN
OBJECTS (STONES, CONCRETE, TIMBER, METAL
OR LARGE FROZEN CHUNKS OF MANURE)
SHOULD NEVER BE LOADED INTO THE
SPREADER.
CLEAR OF SPREADER BEFORE APPLYING
POWER. FAILURE TO HEED MAY RESULT IN SERI-
OUS PERSONAL INJURY OR DEATH.
DANGER: KEEP AWAY AND KEEP OTHERS
CLEAR OF ROTATING SPINNERS AT REAR OF
SPREADER. SERIOUS INJURY OR AMPUTATION
COULD RESULT. FAILURE TO HEED MAY RESULT
IN SERIOUS PERSONAL INJURY OR DEATH.
DANGER: NEVER ENTER THE SPREADER
BOX FOR ANY REASON WITHOUT FIRST DISCON-
NECTING PTO SHAFT FROM TRACTOR. DO NOT
ALLOW OTHERS IN THE BOX. ROTATING AUGERS
CAN CRUSH AND DISMEMBER. FAILURE TO HEED
MAY RESULT IN SERIOUS PERSONAL INJURY OR
DEATH.
When you are ready to begin spreading application on
the field, open the hydraulic flow control rear gate and
slowly engage the tractor PTO clutch. This can be done
while traveling forward to avoid a heavier application of
liquid manure at the edge of the field than desired.
CAUTION: DO NOT USE JACK EXCEPT
WHEN SPREADER IS EMPTY. JACK WILL NOT
For liquid and semi-liquid manure, the application rate
can be controlled by the amount the flow control rear
gate is opened. The gate indicator on the front of the box
will provide a ready reference for the amount of opening.
For solid manure (dry, pen-packed or manure contain-
ing long straw or hay) the flow control rear gate MUST
be completely open since this material is not free flow-
ing.
SUPPORT
ADDED
WEIGHT.
UNBALANCED
WEIGHT MAY RESULT IN UNEXPECTED “TIP UP”
OF SPREADER.
Before loading, especially in freezing weather, make
sure the augers and spinners are free to rotate and the
flow control rear gate moves freely up and down.
VERY IMPORTANT: THIS MACHINE IS NOT
INTENDED TO BE A BALE GRINDER, HAY
Check and be sure that the flow control rear gate is
completely closed before loading.
CHOPPER OR BEDDING MACHINE. LONG HAY OR
STRAW MUST CONTAIN MANURE IN ORDER TO
BE SPREAD. FAILURE TO COMPLY MAY DAMAGE
THE DRIVETRAIN AND VOID THE WARRANTY.
When the spreader is parked for loading, shift the tractor
to neutral or park and set the brakes. The moisture con-
tent of the manure will determine how full the spreader
can be loaded so that no manure spills out.
You will probably be able to load solid manure at least
level with the top of the box while semi-liquid and liquid
manure will have to be less than full in the spreader box.
It is unlawful to allow manure to splash or leak onto pub-
lic roads.
A liquid manure kit is available for installation around the
top of the box on your spreader which will aid in the con-
tainment of liquids.
FIGURE 4. FLOW CONTROL GATE
INDICATOR
Model 8720/8865
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
The rear spinners have been designed and tested to
provide the best spread pattern for most liquids and
semi solid manure. However, the pattern will vary for
each specific condition. The factors that contribute most
to differing patterns will be moisture content and the
amount and length of bedding material. For most typical
conditions, the spread pattern should be uniform and
about 15 ft. wide. When this is the case, plan your
spreading patterns so you do not have to travel over pre-
viously spread manure which will be slippery, resulting
in poor traction. Traction on wet grass is also poor.
When the resulting pattern may require that you over-
lap during spreading, use precautions on slopes and
hills where you could experience a loss of traction by
traveling over ground with previously spread manure.
SHEAR SPROCKET INSTRUCTIONS
The Meyer Spreader you have received has been
equipped with a shear sprocket design on the main au-
ger drive sprockets. The augers are being driven by two
allen head grade 8 bolts. The design is such that if the
bolts are sheared another set of holes to install new
shear bolts will always be accessible without turning
over the machine.
DANGER: AT NO TIME SHOULD
INSTALLATION BE DONE WITH ANYONE ON THE
TRACTOR. SHUT THE TRACTOR OFF, REMOVE
THE KEY AND DISCONNECT THE DRIVE LINE
BEFORE DOING ANY SERVICE ON THIS
MACHINE. SERIOUS INJURY OR DEATH MAY
NOTE: Further control of the application rate is possible
by the relationship of tractor engine speed to ground
speed (transmission gear selection). For optimum, trou-
ble-free performance it is recommended to operate at or
near engine PTO speed.
OCCUR IF SAFETY IS NOT FOLLOWED.
The plate sprocket is set up with the initial drive bolts be-
ing 9/16” diameter (Prior to serial # SI088865/8720287),
5/8” diameter (Serial # SI088865/8720287 and later).
Install the new bolts in the proper way as to drive off of
THE HEAD of the bolt, not on the nut.
When the spreader is empty, idle the tractor and stop
the PTO. Close the flow control rear gate.
Part #
Description
WARNING: NEVER OPERATE PTO ABOVE
ITS NORMAL 540 or 1000 RPM RATING. TRAC-
TOR’S PTO MUST MATCH IMPLEMENT PTO.
831-5618-1.75
9/16-20x1-3/4” Allen Head
Cap Bolt
831-5618-2.25
9/16-20x2-1/4” Allen Head
Cap Bolt
NOTE: Failure to idle the tractor before disengaging the
PTO will cause roller chain over-running and damage to
the chain tighteners.
884-5618
9/16-20 Top Locknut Grade 8
831-6318-1.75
5/8-18x1-3/4” Allen Head
Cap Bolt
884-6318
910-0100
5/8-18 Top Locknut Grade 8
NOTE: Maximum life of the PTO shaft universal joints
will result if you stop the PTO while making turns at the
end of the field.
140B35 Shear Sprocket As-
sembly Complete
CAUTION: DO NOT EXCEED THE MAXIMUM
80° TURNING ANGLE ON THE CONSTANT VELOC-
ITY PTO DRIVELINE. EXCEEDING THE TURNING
ANGLE WILL DAMAGE THE CONSTANT VELOCITY
“CENTER HOUSING” AND WILL EXERT EXCES-
SIVE PRESSURES ON THE PTO INPUT CENTER
SHAFT AND RELATED BEARINGS.
Model 8720/8865
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE AFTER USE
WARNING: DISCONNECT PTO DRIVE
SHAFT AND HYDRAULIC HOSES BEFORE
CLEANING, ADJUSTING, OR SERVICING THIS MA-
CHINE. FAILURE TO HEED MAY RESULT IN SERI-
OUS PERSONAL INJURY OR DEATH.
Before storing this spreader for an extended period of
time perform the following:
Allow the spreader to completely clean out the last load.
Thoroughly hose off all manure from the outside of the
spreader and the inside of the box, particularly getting
the flow control rear gate mechanism clean. The wash
water can be drained into your manure storage pit, or if
the gate is left closed, the water can be spread on the
field. After cleaning, completely lubricate the entire
spreader to exclude moisture from bearings and to pre-
vent condensation from forming during storage. See
Oil the roller chains by running the spreader at idle
speed while opening the rear gate to activate the auto-
matic oiler system. It is also a good time to inspect all ad-
justments and check for parts that need repair or
replacement. Performing these tasks now will guaran-
tee that the spreader is ready for use at the beginning of
the next season.
Model 8720/8865
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
PTO DRIVELINE
WARNING:
BEFORE ATTEMPTING TO
DRIVELINE ATTACHMENT
OPERATE THIS SPREADER, READ AND STUDY
ALL SAFETY INFORMATION. IN ADDITION, MAKE
SURE THAT EVERY INDIVIDUAL WHO OPERATES
OR WORKS WITH THE SPREADER, WHETHER
FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR
WITH THESE SAFETY PRECAUTIONS.
The cutout clutch end of the PTO driveline must always
be attached to the implement. The PTO driveline is
equipped with a 1 3/8-6 spline on the implement half for
attaching to the spreader. Remove the M17-hexagon
bolt from the splined hub and slide the PTO onto the im-
plement splined input shaft. Install the hexagon bolt
through the hub being sure the bolt is falling into the
groove on the splined shaft. Torque tight using a metric
size M17 6-point socket and torque down to 75 ft. lbs. A
M17 6-POINT METRIC SOCKET MUST BE USED AS
ROUNDING OF HEXAGON BOLT AND INACCU-
RACY OF TORQUE SETTINGS COULD OCCUR.
WARNING: DISCONNECT PTO DRIVE SHAFT
AND HYDRAULIC HOSES (RELIEVE HYDRAULIC
PRESSURE) BEFORE CLEANING, ADJUSTING,
LUBRICATING OR SERVICING THIS SPREADER.
FAILURE TO HEED MAY RESULT IN SERIOUS
PERSONAL INJURY OR DEATH.
If removal of the M-17 hexagon bolt is necessary, use
the same M-17 6-point socket and loosen bolt 1/2 turn.
Insert a 1/4” drift punch in the hole on the opposite side
of the hexagon bolt and tap to loosen the seated portion
of the bolt from the splined hub. Loosen in 1/2 turn incre-
ments and tapping to loosen. After bolt seat has been
released, remove the bolt. If bolt is not unseated, dam-
age to the hexagon bolt will occur.
The Meyer 8720/8865 Industrial Series Spreader is
equipped with a cutout type clutch on the implement half
of the PTO driveline. The clutch is designed to limit the
amount of torque transferred to the machine through the
driveline. If excessive torque is developed the clutch will
disengage. A loud ratcheting sound will be heard and
the transfer of power to the machine will be disrupted.
To reengage the machine simply shut down the PTO
and allow the driveline to come to a stop. The PTO can
then be reengaged to restart the spreader. The cutout
clutch will either reengage upon shut down of the PTO
or just before it comes to a complete stop.
Attach the shield safety chain to a suitable area on the
spreader, preferably to the implement PTO steel shield.
The cutout clutch will disengage if start up is done in an
abrupt or reckless manner. It also will disengage from
foreign materials entering the spinner area of the
spreader. It may also be possible to disengage the
clutch by overloading or flooding the spinners with free
flowing or liquid manure. If PTO clutch fails to reengage
it will be necessary to remove the foreign object from the
spreader before restarting. THERE IS NO FIELD
ADJUSTMENT ON THE CUTOUT CLUTCH.
DANGER: NEVER ENTER THE SPREADER
BOX FOR ANY REASON WITHOUT FIRST
STOPPING THE TRACTOR, SHUTTING THE
TRACTOR OFF AND REMOVING THE KEY,
FIGURE 5. PTO DRIVELINE
PTO SETUP
SETTING
THE
PARKING
BRAKE
AND
DANGER: NEVER ATTEMPT TO PERFORM
ANY WORK ON THIS MACHINE FOR ANY REASON
WITHOUT FIRST STOPPING THE TRACTOR,
SHUTTING THE TRACTOR OFF AND REMOVING
THE KEY, SETTING THE PARKING BRAKE AND
DISCONNECTING THE PTO DRIVELINE FROM THE
TRACTOR AND DISCONNECTING THE HYDRAULIC
HOSES AND RELIEVING HYDRAULIC PRESSURE.
DISCONNECTING THE PTO DRIVELINE FROM THE
TRACTOR. DO NOT ALLOW OTHERS IN THE BOX.
ROTATING
AUGERS
CAN
CRUSH
AND
DISMEMBER. FAILURE TO HEED MAY RESULT IN
SERIOUS PERSONAL INJURY OR DEATH.
Model 8720/8865
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
FAILURE TO HEED MAY RESULT IN SERIOUS PER-
SONAL INJURY OR DEATH.
CV center housing (Key #2)-Add grease
until it is evident around the center sliding
disk.
Adjust the drawbar at 16-20” above the ground. Extend
or shorten the drawbar so horizontal distance from end
of tractor PTO shaft to center of hitch pin hole is 16” for
1000 RPM 1-3/8-21 spline, 20” for 1000 RPM 1-3/4-20
spline. Secure the drawbar so the hitch pin hole is lo-
cated directly below the PTO driveline. PTO adapters
are not recommended as damage to the driveline may
occur. A hitch pin with a minimum diameter of 1-5/16”
and bottom retaining pin is recommended.
Telescoping members (Key #3)-Add
grease until it adequately covers the
sliding members. Take apart
occasionally to make sure adequate
lubrication is being added.
Shield bearings (Key #4)-Add 2-3 pumps.
FAILURE TO FREQUENTLY GREASE THE CV
CENTER HOUSING AND TELESCOPING MEMBERS
WILL REDUCE THE LIFE OF THE CV.
AN IMPROPERLY LOCATED HITCH POINT MAY
CAUSE DAMAGE TO THE UNIVERSAL JOINTS
OF THE PTO DRIVE SHAFT. CONFORMING TO
THE DRAWBAR AND PTO RELATIONSHIP
THAT THE PTO DRIVESHAFT WILL NOT
BECOME OVER EXTENDED. USE THE
CORRECT SETTING FOR 14” - 540RPM 1 3/8-6,
16” - 1000RPM 1 3/8-21 OR 20” - 1000RPM 1
3/4-20. WITH INITIAL HOOK-UP TO YOUR NEW
MEYER SPREADER TEST PTO TRAVEL BY
TURNING EQUIPMENT IN BOTH DIRECTIONS
OBSERVING THE MINIMUM AND MAXIMUM
TRAVEL DIMENSIONS AS SHOWN PER
FIGURE 6. PTO DRIVELINE
MAINTENANCE INFORMATION
It is extremely important to follow the maintenance
guidelines. If telescoping members become hard to
slide during normal operation, it is recommended the
shaft be taken apart, cleaned with solvent and recoated
with grease before re-assembling. As a minimum it is
important this be done after each season of use.
LUBRICATION
LUBRICATION
A high quality Lithium Base Grease should be used
PRIOR TO USE
Using the CV Zerk (Key #2) place 20 pumps of
grease into the CV center housing. This should
be done with the driveline / CV as straight as
possible.
Slowly articulate the double joint through its
maximum joint angle several times.
Return the CV joint to its straight position and
insert additional grease into the CV Zerk (Key
#2) until grease is evident around the housing
and center sliding disk.
NORMAL OPERATION
Lubricate the following items after every eight
(8) hours of operation. If short rows and
frequent turning or other demanding conditions
exist, lubricate at four (4) hour intervals.
Cross and bearings (Key #1)-Add grease
until it is purged around the seals
Model 8720/8865
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC
PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE
TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
FRONT DRIVE ROLLER CHAINS
There are six roller chain drives located at the front of the spreader. Regularly check that all tensioning springs are in
serviceable condition for automatic roller chain tightening. Manually adjust spring tensioners (as needed) by turning
double locknuts on all tensioning bolt/idler assemblies. Proper roller chain tension is when 1/4" to ½" deflection
occurs on the slack side of the chain. Regularly re-check all roller chain tensions. Keep all roller chains tight at all
times! For clarity purposes, the following illustrations detail each roller chain reduction separately.
NOTE: The side bars of the roller chains will wear into the idler nylon rollers up to the rollers of the roller chain forming
grooves. These grooves will serve as a guide when the roller chain loosens due to normal use. From this point on,
after tightening, the idler nylon rollers should run for hundreds of hours without any noticeable wear.
IDLER NYLON
RH TOP
SPROCKET
The first chain drive (PTO input shaft to the large RH top
loaded idler nylon roller. The extension spring should
extend 2” from its neutral 5” total length.
ROLLER
CHAIN
Manual adjustment for the automatic tensioning idler,
nylon roller assembly is located at the left rear of the
spreader’s front bearing mounting plate.
PTO
INPUT
SPRING LOADED
ADJUSTER
FIGURE 8. FIRST CHAIN DRIVE
LH TOP SPROCKET
ROLLER CHAIN
The second chain drive (large RH top sprocket to the
tensioned by a spring loaded idler nylon roller. The
extension spring should extend 2“ from its neutral 5"
total length.
IDLER NYLON
ROLLER
Manual adjustment for the automatic tensioning idler,
nylon roller assembly is located at the left rear of the
spreader’s front bearing mounting plate.
SPRING LOADED
ADJUSTER
FIGURE 7. SECOND CHAIN DRIVE
Model 8720/8865
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
IDLER NYLON
ROLLER
ROLLER CHAIN
The third chain drive is automatically tensioned by a
spring-loaded nylon idler roller. The compression spring
To increase tension on the automatic tightener, tighten
the adjuster bolt located at the left side of the spreader.
TENSIONER
ARM
FIGURE 11 . THIRD CHAIN DRIVE
IDLER NYLON
ROLLER
SPRING LOADED
ADJUSTER
tensioned by a spring loaded idler nylon roller. The com-
pression spring should be compressed to 4.5" in length.
See figure 10.
ROLLER
CHAIN
To increase tension on the automatic tightener, tighten
the adjuster bolt located at the right side of the
spreader.
RH AUGER
SPROCKET
FIGURE 10. RH AUGER CHAIN DRIVE
THIRD AUGER DRIVE
SPROCKET
IDLER SPROCKET
ADJUSTER BOLT
ROLLER
CHAIN
The LH and third auger chain drive is automatically
tensioned by a spring loaded heavy compression
spring and sliding idler sprocket assembly, figure 9.
The heavy compression spring should be compressed
to 4” in length.
COMPRESSION
SPRING
IDLER
SPROCKET
Manual adjuster bolt for the automatic tensioning idler
assembly is located slightly right of center on the
spreader tank.
LH AUGER
SPROCKET
FIGURE 9. LH & THIRD AUGER CHAIN
DRIVE
Model 8720/8865
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
The side shaft chain drive (PTO input shaft to the side
tensioned by a spring-loaded idler nylon roller. The
extension spring should extend 2" from its neutral 5"
total length.
Manual adjustment for the automatic tensioning idler,
nylon roller assembly is located at the right rear of the
spreader’s front bearing mounting plate.
1/8-3/8”
IDLER NYLON
ROLLER
SIDE LINE SHAFT
DRIVE SPROCKET
SPRING LOADED
ADJUSTER
FIGURE 12. MATERIAL GUIDE
CLEARANCE
tained turn spinners over by hand in the direction by
which the spreader would turn to check clearance. Do
not turn in the opposite direction as front chain tightener
damage could occur. If foreign objects enter the spinner
area the front pivot bolt on the shear arm is designed to
shear. The extension spring will pull the material guide
away from the spinner until the shear bolt is replaced.
The ½-13 x 3 ½” grade 5 replacement machine bolts are
stored under the rear shield. For replacement install
with ½” flat washer on top of shear eye and on bottom of
block and tighten nylon locknut firmly.
PTO INPUT
FIGURE 13. SIDE SHAFT CHAIN DRIVE
SPINNER MATERIAL GUIDES
Regularly inspect and adjust two spinner material
guides located at both the left rear and right rear of the
spreader. Create a 1/8-3/8” clearance between material
mended clearances for maximum spreading pattern.
Adjust to prevent excessive manure build-up on mate-
rial guide inner surfaces. Adjust to prevent manure
chunks or foreign object lodging between material
guides and spinner teeth.
NOTE: Excessive lodging can cause premature spinner
tooth wear, “bent-over” or even breakage.
SHEAR ARM MATERIAL GUIDE
ADJUSTMENT
Adjustment for the 1/8-3/8” clearance of each material
guide to spinner tooth is made by loosening the jam nut
on the linkage arm and turning the linkage arm to either
move the guide in closer or out farther from the spinner
teeth. After adjustment has been made for the 1/8-3/8”
clearance retighten the jam nut to hold the material
guide in place. Once recommended clearance is ob-
Model 8720/8865
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATION
WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC
PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO
HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
DAILY LUBRICATION (every 8-12 loads)
WEEKLY LUBRICATION (every 25-30 loads)
L6
L1
Grease (2) rear spinner lower bearings. These
bearings are grease line fitted to the LR frame channel
of the spreader.
Grease (3) PTO input shaft bearings. These bear-
ings are grease line fitted to the RF frame channel and
the front bearing channel of the spreader.
L7
L2
Grease (5) bearings on the RH side line shaft. The
Oil (6) roller chain drives with automatic oiler at the
front bearing is zerk accessible through the RF steel
shielding. The remaining rear bearings are located
along the RH side of the spreader tank, zerks accessible
through the steel shielding.
front of spreader with clean 30-weight oil. The roller
chains are accessible by opening the front steel shield-
ing cover.
L3
Grease PTO Drive line (9) places with Lithium
L8
Grease (2) tandem wing pivots. Effectively grease
grease every 8 hours.
by jacking up the spreader to relieve pressure points on
the pivot shaft and tandem wing collar. Over greasing is
not possible.
IMPORTANT: GREASE 2 FITTINGS DAILY
L10
Grease (2) flow control rear gate slide guides.
With the flow control rear gate opened, grease the slide
guides from top side. Allow grease to lubricate flow con-
trol rear gate ends and slide guide surfaces. In freezing
weather dump used motor oil down each slide guide
once a week or more often if needed. Over greasing is
not possible.
L4
Grease (7) bearings supporting the three large
L11
jack shaft reduction sprocket weldments, and the third
auger drive shaft on the front drive. The zerks are acces-
sible by the right front side grease bank and through the
access holes in front plate. Be careful not to over
grease.
Grease (1) integral overrunning clutch at rear of
the PTO drive line. The zerk is on the yoke of the cut out
clutch. Use Shell Super Duty or an equivalent lithium
grease.
L5
Grease (2) auger shaft bearings. These bearings
are grease line fitted to the LF and RF frame channels of
the spreader. Over greasing is not possible. 10-15
pumps minimum.
IMPORTANT: Check regularly for any observable lubri-
cant leakage of the (3) gearboxes at the rear of the
spreader. See L12 & L14 under Monthly Lubrication
Model 8720/8865
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
MONTHLY LUBRICATION
L12
Maintain oil level in the corner gearbox at the
centerline of the input shafts. Check regularly for any
observable oil leakage. If oil leakage is excessive,
replace required input/output shaft oil seals. Use
ONLY EP #80-90 wt. gear lube oil or an equivalent in
corner box, only Lighter weight gear lube oil may be
used in temperatures lower than 20°F. Change oil in
the gearboxes after the first season of use and regu-
larly thereafter.
ON CORNER OF
FRAME
L13
Grease (1) brass bushing supporting the rear
shaft of the 3rd auger assembly. This zerk is located
on the left rear corner of the tank above the inner
cross brace.
L14
Maintain the lube level in the (2) spinner gear-
boxes at 3/4 full. Check regularly for any observable
leakage. If leakage is excessive, replace required in-
put/output shaft seals. Lubricate with Semi-Fluid, EP
Lithium Base, Gear Grease.
L15
Clean and repack the wheel hubs with axle
grease annually. Grease hub through zerk in hub
monthly. Be careful not to over grease and force seal
out of back side of hub.
ON CORNER
OF FRAME
L16
L17
Oil slides on front idler tightener assembly.
Grease (4) material guide pin sleeves. (2) lo-
cated on each side of the spreader.
L18
Grease (2) T-post hold down sleeve zerks lo-
cated above the cross channel on the underside of
the spreader. A zerk is located on the front and one
on the rear of the sleeve.
(SHIELDS REMOVED FOR ILLUSTRATIVE
PURPOSES ONLY.)
Model 8720/8865
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
918-0308 (STANDARD 8720) (OPTIONAL 8865) (SERIAL
#SI078720288-SI088720425) (FOR EARLIER MODELS SEE PAGE 24.)
918-0408 (STANDARD 8720) (OPTIONAL 8865) (SERIAL #SI088720426 &
LATER)
PTO DRIVE SHAFT-STAR PROFILE
1000 RPM 1-3/8 21 SPLINE WWE2480 (80 DEGREE C.V.)
Model 8720/8865
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
918-0308 (STANDARD 8720) (OPTIONAL 8865) (SERIAL #SI078720288-SI088720425)
(FOR EARLIER MODELS SEE PAGE 24.)
918-0408 (STANDARD 8720) (OPTIONAL 8865) (SERIAL #SI088720426 & LATER)
PTO DRIVE SHAFT-STAR PROFILE
1000 RPM 1-3/8 21 SPLINE WWE2480 (80 DEGREE C.V.)
KEY
PART NO.
DESCRIPTION
KEY
18
19
20
21
22
23
24
25
26
PART NO.
DESCRIPTION
Support Bearing
Safety Chain
1
918-0208-1-1
Yoke 1-3/8"-21 Splined
Assembly
918-0208-1-11
918-0208-2-7
918-0208-2-8
918-0208-1-10
918-0208-1-12
918-0308-2-6
918-0208-1-13
918-0208-2-10
2
3
918-0208-1-3
918-0208-1-2
Double Yoke
Decal Outer-In Item 12
Decal Inner-In Item 7
Zerk-In Item 7
Grease Zerk in Item 2 &
8
4
5
6
7
918-0308-1-1
918-0208-1-5
918-0208-1-6
918-0308-1-2
Inboard Yoke
Lubrication Decal
Cross and Bearing Kit
Decal-K64
Cross and Bearing Kit
Spring Pin 10 x 80
Profile S5 and Sleeve
Welded Assy.
918-0208-1-1-1 Assembly Collar Kit (Inc.
Ring, Collar & Balls)
8
9
918-0308-2-1
918-0308-2-2
918-0410-2-1
Overrunning Clutch &
S4LGA Profile Assy.
27
918-0208-2-3-1 Clamp Cone Locking Pin
(Prior to serial
#SI088720425)
Cut Out Clutch (Prior to
serial #SI088720425)
918-0410-2-1-1 Clamp Cone Locking Pin
(Serial #SI088720426 &
Later)
Cut Out Clutch (Serial
#SI088720426 & Later)
10
11
12
13
14
918-0208-2-1
918-0208-2-4
918-0308-2-3
918-0308-2-4
918-0308-1-3
Cross and Bearing Kit
Bearing Ring SC25
28
29
918-0308-1
1-3/8-21 Spline Tractor
Half Assy.
Outer Shield Tube OVL
Inner Shield Tube Round
918-0308-2
1000 RPM Implement ½
Assy. (Prior to serial
#SI088720425)
CV Cone and Bearing
Assy.
918-0410-2
1000 RPM Implement ½
Assy. (Serial
#SI088720426 & Later)
15
16
17
918-0308-1-4
918-0308-2-5
918-0208-2-9
Shield Cone 3-Rib
Shield Cone 8-Rib
Screw-In Item 14,15 & 16
KEY PART NO.
DESCRIPTION
1
2
918-0308-2-2-1
Housing
918-0308-2-2-2
Hub (Prior to serial
#SI088720425)
618-0003-2-1
Hub (Serial
#SI088720426 & Later)
3
4
5
6
7
918-0308-2-2-3
918-0208-2-3-5
918-0208-2-3-6
918-0208-2-3-7
918-0208-2-3-1
Spring Pack
Washer
Retaining Ring
Sealing Ring
Clamp Cone Locking
Pin (Prior to serial
#SI088720425)
918-0410-2-1-1
Clamp Cone Locking
Pin (Serial
#SI088720426 & Later)
8
918-0308-2-2-4
918-0208-2-3-9
Cam
NS
NS
Bushing-In Item #2
918-0208-2-3-11 Shim Kit
Model 8720/8865
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
918-0208
PTO DRIVE SHAFT ASSEMBLY
1000 RPM-21 SPLINE / 1-3/8” YOKE WWE2480 (80 DEGREE C.V.)
USED PRIOR TO SERIAL #SI078720287.
FOR LATER MODELS SEE PAGE 22.
Model 8720/8865
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
918-0208
PTO DRIVE SHAFT ASSEMBLY
1000 RPM-21 SPLINE / 1-3/8” YOKE WWE2480 (80 DEGREE C.V.)
KEY PART NO.
DESCRIPTION
KEY PART NO.
DESCRIPTION
Safety Chain
1
918-0208-1-1
Yoke 1-3/8"-21 Splined As-
sembly
18
19
20
21
22
23
24
25
26
918-0208-2-7
918-0208-2-8
Decal Out-In Item 13
2
3
4
5
6
7
8
9
918-0208-1-2
918-0208-1-3
918-0208-1-4
918-0208-1-5
918-0208-1-6
918-0208-2-1
Grease Zerk in item 3
Double Yoke
918-0208-1-10 Decal In-In Item 8
918-0208-2-9
Screw-In Item 15,16 & 17
Inboard Yoke
918-0208-1-11 Support Bearing
918-0208-1-12 Zerk-In Item 8
918-0208-1-13 Cross and Bearing Kit
918-0208-2-10 Decal-K64
Cross and Bearing Kit
Spring Pin 10 x 80
Cross and Bearing Kit
918-0208-1-14 Profile and Sleeve Wa
918-0208-2-2 Overrunning Clutch &
1bGA Profile Assy.
918-0208-2-3-1 Clamping Cone Bolt (In-
cluded in Item 11)
918-0208-1
1-3/8-21 Spline Tractor
Half Assembly
27
28
918-0208-2
1000 RPM Cutout Clutch
Implement Half Assembly
10
918-0208-1-1-1 AS-Lock Kit For Item 1
(Inc. Ring, Collar & Balls)
11
12
13
14
15
16
17
918-0208-2-3
918-0208-2-4
918-0208-2-5
918-0208-1-7
918-0208-1-8
918-0208-1-9
918-0208-2-6
Cut Out Clutch
Bearing Ring SC25
Outer Shield Tube OVL
Inner shield Tube Round
CV Cone & Bearing Assy.
Shield Cone 3 Rib
Shield Cone 8 Rib
KEY PART NO.
DESCRIPTION
Housing
1
2
3
4
5
6
7
8
918-0208-2-3-2
918-0208-2-3-3
918-0208-2-3-4
918-0208-2-3-5
918-0208-2-3-6
918-0208-2-3-7
918-0208-2-3-1
918-0208-2-3-8
918-0208-2-3-9
Hub
Spring Pack
Washer
Retaining Ring
Sealing Ring
Clamp Cone Assembly
Cam
NS
NS
Bushing - In Item #2
918-0208-2-3-11 Shim Kit
Model 8720/8865
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
918-0310 (OPTIONAL 8720) (STANDARD 8865) (SERIAL
#SI078720288-SI088720425) (FOR EARLIER MODELS SEE PAGE 28.)
918-0410 (OPTIONAL 8720) (STANDARD 8865) (SERIAL # SI088720426 & LATER)
PTO DRIVE SHAFT-STAR PROFILE
1000 RPM 1-3/4 20 SPLINE WWE2480 (80 DEGREE C.V.)
Model 8720/8865
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
918-0310 (OPTIONAL 8720) (STANDARD 8865) (SERIAL #SI078720288-SI088720425)
(FOR EARLIER MODELS SEE PAGE 28.)
918-0410 (OPTIONAL 8720) (STANDARD 8865) (SERIAL #SI SI088720426 & LATER)
PTO DRIVE SHAFT-STAR PROFILE
1000 RPM 1-3/4 20 SPLINE WWE2480 (80 DEGREE C.V.)
KEY PART NO.
DESCRIPTION
KEY PART NO.
DESCRIPTION
1
918-0210-1-1
Yoke 1-3/4"-20 Splined
Assembly
19
20
21
22
23
24
25
26
918-0208-2-7
918-0208-2-8
918-0208-1-10
918-0208-1-12
918-0308-2-6
918-0208-1-13
918-0208-2-10
Safety Chain
Decal Outer-In Item 12
Decal Inner-In Item 7
Zerk-In Item 7
2
3
4
5
6
7
918-0208-1-3
918-0208-1-2
918-0308-1-1
918-0208-1-5
918-0208-1-6
918-0308-1-2
Double Yoke
Grease Zerk in Item 2 & 8
Inboard Yoke
Lubrication Decal
Cross and Bearing Kit
Decal-K64
Cross and Bearing Kit
Spring Pin 10 x 80
Profile S5 and Sleeve
Welded Assy.
918-0210-1-1-1 Assembly Collar Kit (Inc.
Ring, Collar & Balls)
8
9
918-0308-2-1
918-0308-2-2
918-0410-2-1
Overrunning Clutch &
S4LGA Profile Assy.
27
918-0208-2-3-1 Clamp Cone Locking Pin
(Prior to serial
#SI088720425)
Cut Out Clutch (Prior to
serial #SI088720425)
918-0410-2-1-1 Clamp Cone Locking Pin
(Serial #SI088720426 &
Later)
Cut Out Clutch (Serial
#SI088720426 & Later)
10
11
12
13
14
918-0208-2-1
918-0208-2-4
918-0308-2-3
918-0308-2-4
918-0308-1-3
Cross and Bearing Kit
Bearing Ring SC25
28
29
918-0310-1
1-3/4-20 Spline Tractor
Half Assy.
918-0308-2
1000 RPM Implement ½
Assy. (Prior to serial
#SI088720425)
Outer Shield Tube OVL
Inner Shield Tube Round
CV Cone and Bearing
Assy.
918-0410-2
1000 RPM Implement ½
Assy. (Serial
#SI088720426 & Later)
15
16
17
18
918-0308-1-4
918-0308-2-5
918-0208-2-9
918-0208-1-11
Shield Cone 3-Rib
Shield Cone 8-Rib
Screw-In Item 15,16 & 17
Support Bearing
KEY PART NO.
DESCRIPTION
1
2
918-0308-2-2-1
Housing
918-0308-2-2-2
Hub (Prior to serial
#SI088720425)
618-0003-2-1
Hub (Serial
#SI088720426 & Later)
3
4
5
6
7
918-0308-2-2-3
918-0208-2-3-5
918-0208-2-3-6
918-0208-2-3-7
918-0208-2-3-1
Spring Pack
Washer
Retaining Ring
Sealing Ring
Clamp Cone Locking
Pin (Prior to serial
#SI088720425)
1 3/8”-6 SPLINE
918-0410-2-1-1
Clamp Cone Locking
Pin (Serial
#SI088720426 & Later)
PRIOR TO SN SI088720425
1 3/4”-20 SPLINE
SN SI088720426 & LATER
8
918-0308-2-2-4
918-0208-2-3-9
Cam
NS
NS
Bushing-In Item #2
918-0208-2-3-11 Shim Kit
Model 8720/8865
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
918-0210
PTO DRIVE SHAFT ASSEMBLY
1000 RPM-20 SPLINE / 1-3/4” YOKE WWE2480 (80 DEGREE C.V.)
USED PRIOR TO SERIAL #SI078720287.
FOR LATER MODELS SEE PAGE 26.
Model 8720/8865
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
918-0210
PTO DRIVE SHAFT ASSEMBLY
1000 RPM-20 SPLINE / 1-3/4” YOKE WWE2480 (80 DEGREE C.V.)
KEY PART NO.
DESCRIPTION
KEY PART NO.
DESCRIPTION
Shield Cone 8 Rib
Safety Chain
1
918-0210-1-1
Yoke 1-3/4"-20 Splined
Assembly
17
18
19
20
21
22
23
24
25
26
918-0208-2-6
918-0208-2-7
918-0208-2-8
2
3
4
5
6
7
8
9
918-0208-1-2
918-0208-1-3
918-0208-1-4
918-0208-1-5
918-0208-1-6
918-0208-2-1
Grease Zerk in item 3
Double Yoke
Decal Out-In Item 13
918-0208-1-10 Decal In-In Item 8
Inboard Yoke
918-0208-2-9
Screw-In Item 15,16 & 17
Cross and Bearing Kit
Spring Pin 10 x 80
Cross and Bearing Kit
918-0208-1-11 Support Bearing
918-0208-1-12 Zerk-In Item 8
918-0208-1-13 Cross and Bearing Kit
918-0208-2-10 Decal-K64
918-0208-1-14 Profile and Sleeve Wa
918-0208-2-2 Overrunning Clutch &
1bGA Profile Assy.
918-0208-2-3-1 Clamping Cone Bolt (In-
cluded in Item 11)
918-0210-1
1-3/4-20 Spline Tractor Half
Assembly
10
27
28
918-0208-2
1000 RPM Cutout Clutch Im-
plement Half Assembly
11
12
13
14
15
16
918-0208-2-3
918-0208-2-4
918-0208-2-5
918-0208-1-7
918-0208-1-8
918-0208-1-9
Cut Out Clutch
918-0210-1-1-1 AS-Lock Kit For Item 1 (Inc.
Ring, Collar & Balls)
Bearing Ring SC25
Outer Shield Tube OVL
Inner shield Tube Round
CV Cone & Bearing Assy.
Shield Cone 3 Rib
KEY PART NO.
DESCRIPTION
Housing
1
2
3
4
5
6
7
8
918-0208-2-3-2
918-0208-2-3-3
918-0208-2-3-4
918-0208-2-3-5
918-0208-2-3-6
918-0208-2-3-7
918-0208-2-3-1
918-0208-2-3-8
918-0208-2-3-9
Hub
Spring Pack
Washer
Retaining Ring
Sealing Ring
Clamp Cone Assembly
Cam
NS
NS
Bushing - In Item #2
918-0208-2-3-11 Shim Kit
Model 8720/8865
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
FIRST REDUCTION & SPINNER DRIVE
KEY PART NO.
DESCRIPTION
QTY
1
1
2
3
925-3720
Tightener Arm Assembly, Spinner Drive
Eyebolt, 5/16 x 5" / 4" Thread Length
1-1/2" 4-Bolt Bearing (Prior to serial #SI088720425)
1-3/4" 4-Bolt Bearing (Serial #SI088720426 & Later)
Extension Spring
933-3804
1
914-3602
3
914-3819
3
4
929-0003
1
5
910-0092
80B15 Sprocket Side Shaft to Spinner Drive (Clamp Style)
Front Side Shaft 121-3/4" Long
2-Bolt, 1-1/2" Bearing
1
6
923-3754
1
7
914-3814
1
8
912-0013
2" Nylon Roller Complete
1
8A
8B
9
912-0013-1
912-0013-2
808-.75-1.25-14
851-7510-3Z
910-3755
2" Nylon Roller Only
1
Inner Sleeve
1
3/4" I.D. x 1-1/4" O.D. x 14Ga. Machine Bushing
3/4-10 x 3" Machine Bolt Zinc
Reduction Sprocket Weldment-Nonshear
Tightener Extension Arm
4
10
11
12
13
14
15
16
1
1
925-3777-1
14-0031
1
2" Bearing 4-Bolt
3
925-3779-1
933-3640
3/4-10 x 3" Machine Bolt-Special
Grease Line, Rear 1st Reduction 21"
1
1
808-1.5-2.25-10
12-Machine Bushings (10 - For Split Sprocket) (Prior to serial
#SI088720425)
AR
808-1.75-2.5-10
12-Machine Bushings (10 - For Split Sprocket)(Serial #SI088720426 &
Later)
AR
17
910-0089
910-0120
925-3601
923-3755
923-3755-S
923-3757
911-0069
911-0054
911-0068
933-3631
933-3646
933-3645
925-3779
35-0010
80B20 1-1/2" Bore Solid Sprocket (Prior to serial #SI088720425)
80B20 1-3/4" Bore Solid Sprocket (Serial #SI088720426 & Later)
Front Bearing Plate
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
18
19
PTO Splined Shaft 1-1/2x42-3/4" (Prior to serial #SI078720427)
PTO Splined Shaft 1-1/2x34-3/4" (Serial #SI078720427-SI088720425)
PTO Splined Shaft 1-3/4x34-3/4" (Serial #SI088720426 & Later)
#80-119 Roller Chain
20
21
21
22
23
24
25
26
27
#80-94 Roller Chain 1000 RPM
#80-78 Roller Chain 540 RPM
Grease Line, Front Center Shaft Bearing
Grease Line, Center Bearing Center Shaft, Left Side
Grease Line, Rear Center Shaft Bearing to Right Side
Tightener Arm Assembly
Key, 3/8 x 1-1/2"
910-0074
80B24 Sprocket 1-1/2" Bore,11 RPM Standard (Prior to Serial
#SI088720425)
910-0121
80B24 Sprocket 1-3/4" Bore,11 RPM Standard (Serial #SI088720426 &
Later)
1
910-0069
80B22 Sprocket 1-1/2" Bore,10 RPM (Prior to Serial #SI088720425)
80B22 Sprocket 1-3/4" Bore,10 RPM (Serial #SI088720426 & Later)
80B18 Sprocket 1-1/2" Bore 8.25 RPM (Prior to Serial #SI088720425)
80B18 Sprocket 1-3/4" Bore 8.25 RPM (Serial #SI088720426 & Later)
80B16 Sprocket 1-1/2" Bore 7.30 RPM (Prior to Serial #SI088720425)
80B16 Sprocket 1-3/4" Bore 7.30 RPM (Serial #SI088720426 & Later)
9-Machine Bushings (6-For Split Sprocket)(Prior to serial #SI088720425)
9-Machine Bushings (6-For Split Sprocket)(Serial #SI088720426 & Later)
Key, 3/8 x 2", Hardened
1
910-0122
1
910-0075
1
910-0123
1
910-0068
1
910-0124
1
28
808-1.5-2.25-10
808-1.75-2.5-10
935-0001
AR
AR
1
29
30
901-3751-30
Rear Bearing Vertical Back Plate Welded Assy. (Serial #SI078720427 &
Later) (Bolt On Plate Only)
1
31
925-3822-6
2-Chain Link For Tightener
1
Model 8720/8865
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECOND REDUCTION DRIVE
KEY
1
PART NO.
933-3804
925-3823-6
929-0003
14-0031
DESCRIPTION
QTY
1
Eyebolt, 5/16 x 5" / 4" Thread Length
4-Chain Link For Tightener
Extension Spring
2
1
3
1
4
2" Bearing 4-Bolt
2
5
925-3777-2
925-3779
851-7510-3Z
933-3642
914-3811
910-3755
910-3753
911-0053
912-0013
912-0013-1
912-0013-2
Tighener Extension Arm
1
6
Tightener Arm
1
7
3/4-10 x 3" Machine Bolt Zinc
Grease Line, 2nd Reduction Rear Bearing, 60”
2-1/2” Bearing, 4-Bolt
1
8
1
9
1
10
11
12
13
13A
13B
14
Reduction Sprocket Weldment-Nonshear
Industrial 2nd Reduction Wldmt
#80-102 Roller Chain, 2nd Reduction Chain
2" Nylon Roller Complete
2” Nylon Roller Only
1
1
1
1
1
Inner Sleeve
1
808-.75-1.25-14 3/4" ID x 1-1/4" OD Machine Bushing 14 Ga.
2
Model 8720/8865
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
THIRD REDUCTION DRIVE
KEY
1
PART NO.
914-3811
DESCRIPTION
QTY
2
2 ½” 4-Bolt Bearing
2
910-3754-HD
911-0062
Industrial 3rd Reduction Weldment
#120-47 Roller Chain, 3rd Reduction Chain
2 ½” Round Bearing
1
3
1
4
914-3807A
925-3783
1
5
Tightener Bolt Assembly
#120 Chain, Tightener Linkage
Tightener Spring
1
6
925-3782
1
7
29-0009
1
8
925-3807-3
815-7510-Z
910-3753-HD
925-3779
Retaining Washer
1
9
3/4-10 Nylon Locknut
2
10
11
12
12A
12B
13
14
15
16
Industrial 2nd Reduction
Tightener Arm
1
1
912-0013
2" Nylon Roller Complete
2" Nylon Roller Only
1
912-0013-1
912-0013-2
808-.75-1.25-14
851-7510-3Z
14-0031
1
Inner Sleeve
1
3/4" ID x 1-1/4" OD Machine Bushing 14 Ga.
3/4-10 x 3" Machine Bolt Zinc
2” Bearing, 4-Bolt
2
1
1
901-3750-49
#120 Tightener Pivot
1
Model 8720/8865
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL REDUCTION, RH AUGER DRIVE
KEY
1
PART NO.
933-3701
DESCRIPTION
QTY
1
3" Retaining Ring
2
910-0100
140B35 Shear Sprocket Assembly
1
2A
831-5618-1.75
9/16-18 x 1-3/4" Allen Head Cap Screw Grade 8 (Prior to Serial
#SI088720/8865287)
AR
831-5618-2.25
831-6318-1.75
9/16-18 x 2-1/4" Allen Head Cap Screw Grade 8 (Prior to Serial
#SI088720/8865287)
AR
AR
5/8-18 x 1-3/4" Allen Head Cap Screw Grade 8 (Serial
#SI088720/8865287 & Later)
2B
884-5618
9/16-18 Top Locknut Grade 8 (Prior to Serial #SI088720/8865287)
5/8-18 Top Locknut Grade 8 (Serial #SI088720/8865287 & Later)
140-47 Roller Chain
AR
AR
1
884-6318
3
911-0065
4
933-3704
Front Auger Washer Steel
1
5
933-3750
Auger Sprocket Spacer 1-1/2" Long
Nylon Bushing 3" I.D. x 4" O.D. x 3-3/8" Long
Front Bushing Holder Assembly W/Nylon
Grease Line, Right Auger Bushing Holder
Right Auger Chain Tightener Linkage
Tightener Spring
1
6
913-3701
1
7
925-3766
1
8
933-3626
1
9
925-3781
1
10
11
12
13
14
15
16
17
17A
17B
18
19
20
21
22
29-0009
1
925-3807-3
815-7510-Z
925-3783
Retaining Washer
1
3/4-10 Nylon Locknut
1
Tightener Bolt Assembly
1
914-3807A
910-3754-HD
914-3811
2-1/2" Round 4-Bolt Bearing
1
3rd Reduction Weldment
1
2-1/2" Bearing 4-Bolt
1
912-0013
2" Nylon Roller Complete
1
912-0013-1
912-0013-2
808-.75-1.25-14
925-3778
2" Nylon Roller Only
1
Inner Sleeve
1
3/4" I.D. x 1-1/4" O.D. Machine Bushing 14 Ga.
Right Auger Tightener Arm Assembly Less Roller
3/4-10 x 2-3/4" Machine Bolt Special
#120 Tightener Pivot
2
1
925-3778-3
901-3751-11
933-3641
1
1
Grease Line, 2-1/2" Rear Bearing
1
Model 8720/8865
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL REDUCTION, LH AUGER & THIRD AUGER DRIVE
KEY
1
PART NO.
DESCRIPTION
QTY
1
914-3811
2-1/2" Bearing 4-Bolt
2
910-3754-HD
925-3719-4
912-0008
8720 3rd Reduction Weldment
3/4-10 x 3-1/2" Machine Bolt-Special
140C12 Idler Sprocket
1
3
1
4
1
4A
5
910-0006-1
910-0087
Idler Bearing
2
140B28 2-1/2" Bore Sprocket
2-1/2" Bearing 4-Bolt
1
6
914-3811
1
7
805-0075-Z
914-3807A
925-3732
3/4" Flat Washer
AR
1
8
2-1/2" Round Bearing
9
Tightener Bolt Welded Assembly
Outer Spring Tightener Guide
Compression Spring
1
10
11
12
13
13A
925-3841
1
29-0009
1
925-3719
#140 Chain Tightener Bracket Assembly
140B35 Shear Sprocket Assembly
1
910-0100
1
831-5618-1.75
9/16-18 x 1-3/4" Allen Head Cap Screw Grade 8 (Prior to Serial
#SI088720/8865287)
AR
831-5618-2.25
831-6318-1.75
9/16-18 x 2-1/4" Allen Head Cap Screw Grade 8 (Prior to Serial
#SI088720/8865287)
AR
AR
5/8-18 x 1-3/4" Allen Head Cap Screw Grade 8 (Serial
#SI088720/8865287 & Later)
13B
884-5618
884-6318
911-0067
933-3701
933-3704
925-3731
913-3701
925-3766
933-3644
933-3641
901-3701-36
35-0024
9/16-18 Top Locknut Grade 8 (Prior to Serial #SI088720/8865287)
5/8-18 Top Locknut Grade 8 (Serial #SI088720/8865287 & Later)
#140-80 Roller Chain, Left Auger Chain
3" Retaining Ring
AR
AR
1
14
15
16
17
18
19
20
21
22
23
1
Front Auger Washer Steel
1
#140 Tightener Angle Welded Assembly
Nylon Bushing 3" ID x 4" OD x 3-3/8" Long
Front Bushing Holder Assembly W/Bushing
Grease Line, Left Auger Bushing Holder
Grease Line, 2-1/2" 3rd Auger Bearing
Tightener Slide Welded Assembly
1
1
1
1
1
2
½ x ½ x 2-1/2" Square Key
1
Model 8720/8865
-39-
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY, SHIELDS & AUGERS - 8720 SPREADER
KEY PART NO.
1
DESCRIPTION
Splash Guard Assy.
45°
QTY
2
27
28
29
924-3758-1
925-3775-1
901-3759-2
Center Shaft Shield
PTO Holder Bracket
1
1
1
901-3765
Bolt On Swivel Hitch
Assembly
901-3769
Splash Guard Assy.
75°
2
29A
901-3755-4
1-14x6-1/2" Grade 8
Machine Bolt
4
2
3
4
5
926-3764
933-3703
913-3701
925-3770
3rd Auger Assy.
Bronze Washer
Nylon Bushing
1
1
1
1
29B
30
884-1014-Z
956-3702-1
956-3702-2
1-14 Top Locknut Gr 8
Jack
Jack Mount Tube
4
1
1
1
1
3rd Auger Bushing
Holder W/Nylon
Right Auger Assy.
30A
30B
30C
956-3702-1-1 Pin & Chain Assy.
956-3702-1-3 Screw Nut/Bearing
Washer Kit
6
926-3763
926-3701-2
1
1
1
Front Splined Sleeve
926-3701-2-1 Rear Splined Sleeve
W/Cap Washer
30D
956-3702-1-2 Gear Bushing Pin Re-
pair Kit
1
926-3750-3
926-3770-2
926-3771-1
Front Seal Collar
Flighting Gusset
1
31
32
33
33-0044
46-7000-1
925-3762
Manual Holder W/Cap
Gate Indicator Decal
1
1
1
2
AR
3/8" Right Hand Sec-
tional Flighting
Right Auger Knife
Gate Indicator Assem-
bly
Indicator Pipe
926-3771-2
1
2
34
35
36
37
38
39
40
41
42
925-8720-1
955-3701
955-3803
955-3609
955-3760
955-3605
955-3756
955-3825
924-3762
1
2
1
1
2
2
2
2
1
7
8
9
914-3812-
NSM
914-3813
Front Auger Thrust
Bearing, NSM Nylatron
3/8 x 132” Hyd. Hose
3/8" Black Pipe Tee
3/8" Black Coupler
3/8 x 198" Hyd. Pipe
3/8 x 90° Black Elbow
3/8 x 24" Hyd. Pipe
3/8 x 56" Hyd. Hose
Front Auger Thrust
Bearing Seal
2
2
2
926-3701-1
Splined Auger Shaft 23
Tooth 3" Diameter
10
11
933-3701
926-3762
926-3701-2
3" Retaining Ring
Left Auger Assy.
Front Splined Sleeve
R. Lower Auger
Sprocket Shield Assy.
1
1
926-3701-2-1 Rear Splined Sleeve
W/Cap Washer
43
44
924-3763
L. Lower Auger
Sprocket Shield Assy.
Front Outer Plate Assy. 1
1
926-3750-3
926-3770-2
926-3770-1
Front Seal Collar
Flighting Gusset
1
925-3750
2
AR
925-3750-TR Front Outer Plate Assy. 1
Truck Mount
3/8" Leftt Hand Sec-
tional Flighting
Left Auger Knife
45
46
901-8720
933-3632
Main Body
Grease Line 3rd Auger
Rear Bearing 36"
1
1
926-3770-5
32-0027-1
925-3771-9
1
1
4
12
13
Upper T-Latch Bracket
Nylon Bearing (2-Per
Auger)
47
929-3801
Hydraulic Hose Holder
Spring
1
14
15
16
17
925-3773
Auger Holdown Assy.
W/Nylon
1
1
1
1
48
49
50
51
52
53
54
55
56
57
823-.25-5Z
933-3704
931-3810
937-0004
35-0022
1/4 x 5” Hair Pin
Steel Washer
4
1
1
1
1
2
1
1
1
1
925-3771-4
T-Post Holdown Bot-
tom Collar
PTO Guard Assy.
1-1/2" Shaft Coupler
3/8 x 3/8 x 4-1/2" Key
Male Pioneer Tip
Gas Lift Assist Spring
Front Side Shaft
Rear Side Shaft
881-1008-5Z 1-08 x 5" Grade 8 Ma-
chine Bolt
55-0013
884-1008
1-08 Grade 8 Top
Locknut
955-3703
923-3756
923-3704
924-3752
18
19
20
21
924-3755
924-3766
914-3814
914-3804
Rear Side Shield
Front Side Shield
2-Bolt 1-1/2" Bearing
1
1
5
1
Right Hand Front
Cover
1-1/2" Pillow Block
Bearing
Front Cover Assembly
58
59
60
61
62
63
933-3602
933-3753
933-3801
933-3802
925-3774
56-0029
Hydraulic Pipe Bracket
Shaft Collar 2-1/2"
Bronze Washer 2-1/2"
Steel Washer 2-5/8"
Mirror Bracket
5
1
1
1
1
1
22
23
924-3753
924-3756
1
1
Right Front Shield As-
sembly
Rubber T-Latch
24
25
26
32-0027-2
32-0027-3
924-3757
1
1
1
Lower T-Latch Bracket
Left Front Support
Plate
Mirror
Model 8720/8865
-41-
Download from Www.Somanuals.com. All Manuals Search And Download.
BODY, SHIELDS & AUGERS - 8865 SPREADER
DESCRIPTION
KEY PART NO.
901-3765
QTY
2
KEY PART NO.
884-1014-Z
DESCRIPTION
QTY
4
1
Splash Guard Assy.
45 Degree
29B
1-14 Top Locknut
Grade 8
Jack
2
3
4
5
926-3760
933-3703
913-3701
925-3770
3rd Auger Assy.
Bronze Washer
Nylon Bushing
1
1
1
1
30
956-3702-1
956-3702-2
956-3702-1-1
956-3702-1-3
1
1
1
1
30A
30B
30C
Jack Mount Tube
Pin & Chain Assy.
3rd Auger Bushing
Holder W/Nylon
Right Auger Assy.
Screw Nut/Bearing
Washer Kit
6
926-3770
926-3701-2
926-3701-2-1
1
1
1
30D
956-3702-1-2
Gear Bushing Pin Re-
pair Kit
1
Front Splined Sleeve
Rear Splined Sleeve
W/Cap Washer
31
32
33
33-0044
46-7000-1
925-3762
Manual Holder W/Cap
Gate Indicator Decal
1
1
1
926-3750-3
926-3770-2
926-3771-1
Front Seal Collar
Flighting Gusset
1
Gate Indicator Assem-
bly
Indicator Pipe
2
AR
34
35
36
37
38
39
40
41
42
925-3765
955-3701
955-3803
955-3609
955-3755
955-3605
955-3756
955-3825
924-3762
1
2
1
1
2
2
2
2
1
3/8" Right Hand Sec-
tional Flighting
Right Auger Knife
3/8 x 132" Hyd. Hose
3/8" Black Pipe Tee
3/8" Black Coupler
3/8 x 238" Hyd. Pipe
3/8 x 90* Black Elbow
3/8 x 24" Hyd. Pipe
3/8 x 56" Hyd. Hose
926-3771-2
914-3812- NSM
1
2
7
8
9
Front Auger Thrust
Bearing
914-3813
Front Auger Thrust
Bearing Seal
2
2
2
926-3701-1
Splined Auger Shaft
23 Tooth 3" Diameter
R. Lower Auger
Sprocket Shield Assy.
10
11
933-3701
926-3771
3" Retaining Ring
Left Auger Assy.
Front Splined Sleeve
43
44
924-3763
L. Lower Auger
Sprocket Shield Assy.
1
1
1
926-3701-2
926-3701-2-1
1
1
Rear Splined Sleeve
W/Cap Washer
925-3750
Front Outer Plate
Assy.
926-3750-3
926-3770-2
926-3770-1
Front Seal Collar
Flighting Gusset
1
925-3750-TR
Front Outer Plate
Assy. Truck Mount
Main Body
2
AR
3/8" Leftt Hand Sec-
tional Flighting
Left Auger Knife
45
46
901-3751
933-3647
1
1
Grease Line 3rd Auger
Rear Bearing
926-3770-5
32-0027-1
925-3771-9
1
1
4
12
13
Upper T-Latch Bracket
Nylon Bearing (2-Per
Auger)
47
929-3801
Hydraulic Hose Holder
Spring
1/4x5” Hair Pin
1
48
49
50
51
52
53
54
55
56
57
823-.25-5Z
933-3704
931-3810
937-0004
35-0022
4
1
1
1
1
2
1
1
1
1
14
15
16
17
925-3773
Auger Holdown Assy.
W/Nylon
1
1
1
1
Steel Washer
PTO Guard Assy.
1-1/2" Shaft Coupler
3/8 x 3/8 x 4-1/2" Key
Male Pioneer Tip
Gas Lift Assist Spring
Front Side Shaft
Rear Side Shaft
925-3771-4
881-1008-5Z
884-1008
T-Post Holdown Bot-
tom Collar
1-08 x 5" Grade 8 Ma-
chine Bolt
55-0013
955-3703
923-3754
923-3704
924-3752
1-08 Grade 8 Top
Locknut
18
19
20
21
924-3755
924-3754
914-3814
914-3804
Rear Side Shield
Front Side Shield
2-Bolt 1-1/2" Bearing
1
1
5
1
Right Hand Front
Cover
58
59
60
61
62
63
933-3602
933-3753
933-3801
933-3802
925-3774
56-0029
Hydraulic Pipe Bracket
Shaft Collar 2-1/2"
Bronze Washer 2-1/2"
Steel Washer 2-5/8"
Mirror Bracket
5
1
1
1
1
1
1-1/2" Pillow Block
Bearing
Front Cover Assembly
22
23
924-3753
924-3756
1
1
Right Front Shield As-
sembly
Rubber T-Latch
Mirror
24
25
26
32-0027-2
32-0027-3
924-3757
1
1
1
Lower T-Latch Bracket
8865 Left Front Sup-
port Plate
27
28
29
924-3758-1
925-3775-1
901-3757
Center Shaft Shield
PTO Holder Bracket
1
1
1
Bolt On Swivel Hitch
Assembly
29A
881-1014-2.5Z
1-14x2-1/2" Grade 8
Machine Bolt
4
Model 8720/8865
-43-
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR GATE & SHIELDS
KEY PART NO.
DESCRIPTION
QTY
KEY PART NO.
DESCRIPTION
QTY
1
925-3759
Back Cylinder Plate
Weldment
1
31
925-3763
Gate Indicator Link-
age
1
2
3
925-3758-1
901-3766
Front Cylinder Plate
1
1
32
75-0413-1A
Machine Bolt, Gr 5,
1-14 x 4”
2
Rear Gate Assembly
W/Peg
33
34
35
36
75-0305-2
884-1014-Z
925-13903
Jam Nut, 1-14, RH
Top Locknut, 1-14
1-3/8" Shear Sleeve
2
4
5
6
949-3750
901-3764-1
955-0011
Poly Gate Slides
Rear Gate Guide
2
2
1
2
2
Hydraulic Cylinder
Center Lift
925-13803-K Linkage Arm Kit
IT
AR
7
955-3802-2
955-3605
925-3754
955-3753
55-0092
½ x 3/8" Steel Hex
Bushing
1
1
1
1
1
1
1
37
33-1009
Plastic Trim (By the
Foot)
AR
8
3/8 x 90 Degree El-
bow
38
39
949-3751
924-3759
Top Poly Gate Seal
1
1
Rear Shield Right
Cap
9
Hydraulic Pipe
Holder Weldment
40
41
42
43
44
32-0027-1
949-3752
925-13802
925-13801
925-13803
929-0003
Upper T Latch
Bracket
1
1
1
1
2
10
11
12
13
3/8 x 32" Hydraulic
Pipe
Poly Gate Seal
Spacer
Street Elbow ½" M x
3/8" Female
L. Cupped Material
Guide
924-3761
924-3750-2
Right Rear Upper
Shield
R. Cupped Material
Guide
Rear Shield Upper
Mount Plate Assy.
Material Guide Link-
age Arm
14
15
924-3751
924-3750
Rear Shield Left Cap
1
1
Rear Main Cover
Assy.
45
46
Extension Spring
2
2
925-3768-1- Frame Pivot Block
3-DT
16
17
33-1002
Slow Moving Vehicle
Bracket
1
1
47
48
955-0011-A
SSY
Cylinder w/Brk &
Pipe
1
1
924-3760
Rear Shield Lower
Mount Plate Assy.
901-3751-40 Rear Spinner Deflec-
tor Weld on Replace-
ment
18
19
32-0027-2
32-0027-3
Rubber T-Latch
1
1
Lower T-Latch
Bracket
20
955-3703
Gas Lift Assist
Spring
1
21
22
925-3760-1
925-3761-1
Gearbox Rear Plate
1
1
Gearbox Mount
Strap
23
24
925-13804-1 1" Shear Sleeve
2
2
925-13902
RH Tie Rod Eye
Welded Assy.
W/Jam Nut
25
827-2528-38 Set Screw, 1/4-28 x
3/8”
4
26
27
28
815-5013-Z
805-0050-Z
Nylon Locknut, ½-13
Flat Washer, ½
6
12
2
851-5013-3. Machine Bolt, ½ x
5Z
3-1/2” Grade 5
29
30
75-0304
LH Tie Rod Eye
W/Jam Nut
2
1
925-3767
Indicator Linkage
Assy.
Model 8720/8865
-45-
Download from Www.Somanuals.com. All Manuals Search And Download.
SPINNERS & GEARBOXES
KEY
1
PART NO.
901-13802
901-13801
901-3753-10
933-3632
DESCRIPTION
QTY
1
Left Spinner Assembly
2
Right Spinner Assembly
1
3
Paddle Tip
AR
1
4
Grease Line, Left Spinner Bearing
Grease Line, Right Spinner Bearing
L. Spinner Sand Paddle
5
933-3639
1
7
901-3753-16
815-3824-Z
851-3824-1.5Z
19-0129
4
8
3/8-24 Nylon Insert Locknut
3/8-24 x 1-1/2" Fine Thread GR 5 Bolt
Left Spinner Gearbox
4
9
4
10
11
12
1
19-0130
Right Spinner Gearbox
1
19-0036
Corner Gearbox 1000 RPM Standard
Optional 540 Corner Gearbox
1 3/4 x 2 ½ x 14 GA M.B. (Prior to SI078720/8865395)
1 3/4” Bore Chain Coupler
Coupler Chain
1
19-0035
1
13
14
15
16
17
18
19
20
22
23
24
25
26
27
808-1.75-2.5-14
937-0010-1
937-0009-2
935-0001
AR
2
2
3/8 x 3/8 x 2” Key, Hardened
1 ½” Bore Chain Coupler
8
937-0009-1
937-0009
2
1 ½” Chain Coupler Kit (Prior to 08 SN’s)
1 3/4” Chain Coupler Kit
1
937-0010
1
901-3753-15
914-3815
R. Spinner Sand Paddle
4
2” - 4 Bolt Bearing
2
901-3754-2
901-3753-13
901-3753-19
901-3753-20
937-0020
LH Poultry/Sludge Paddle
RH Poultry/Sludge Paddle
LH Sludge/Paste Paddle
2
2
2
RH Sludge/Paste Paddle
2
Over Running Clutch (08 Models and Later)
1
Model 8720/8865
-47-
Download from Www.Somanuals.com. All Manuals Search And Download.
SPINNER GEAR REDUCER - LEFT HAND (1:1) #19-0129
USE FLUID GEAR GREASE ONLY.
DO NOT USE OIL FOR LUBRICANT.
KEY
1
PART NO.
19-0029-2
19-0029-1
19-0029-3
19-0129-1
19-0029-5
19-0029-6
19-0029-7
19-0029-8
19-0029-9
19-0029-10
19-0029-11
19-0016-11
19-0016-5
19-0029-14
55-0107
DESCRIPTION
Casting, Machined (Thru Holes)
Casting, Machined (Tapped Holes)
Assy, Pinion Shaft/Gear
Assy, Cross Shaft/Gear
Bearing Cone
2
3
4
5
6
Bearing Cup
7
Bearing Cone
8
Bearing Cup
9
Seal 1-3/4"
10
11
12
13
14
15
16
End Plug, Rubber Cover
Retaining Ring, 1.750
Bolt, 3/8-16 x 2.250 SHCS
Plug, ½ NPT
Bushing, 1/4 NPT to 1/8 NPT
Plug, Breather
19-0029-16
Bearing Cone
Model 8720/8865
-48-
Download from Www.Somanuals.com. All Manuals Search And Download.
SPINNER GEAR REDUCER - CENTER (1:1) #19-0130
USE FLUID GEAR GREASE ONLY.
DO NOT USE OIL FOR LUBRICANT.
KEY
1
PART NO.
DESCRIPTION
19-0029-2
19-0029-1
19-0029-3
19-0130-1
19-0029-5
19-0029-6
19-0029-7
19-0029-8
19-0029-9
19-0029-10
19-0029-11
19-0016-11
19-0016-5
19-0029-14
55-0107
Casting, Machined (Thru Holes)
Casting, Machined (Tapped Holes)
Assy, Pinion Shaft/Gear
Assy, Cross Shaft/Gear
Bearing Cone
2
3
4
5
6
Bearing Cup
7
Bearing Cone
8
Bearing Cup
9
Seal 1-3/4"
10
11
12
13
14
15
16
End Plug, Rubber Cover
Retaining Ring, 1.750
Bolt, 3/8-16 x 2.250 SHCS
Plug, ½ NPT
Bushing, 1/4 NPT to 1/8 NPT
Plug, Breather
19-0029-16
Bearing Cone
Model 8720/8865
-49-
Download from Www.Somanuals.com. All Manuals Search And Download.
CORNER GEAR REDUCER - RIGHT HAND
IMPORTANT!
USE #80-90 WT. GEAR LUBE OIL ONLY.
DO NOT USE GREASE FOR LUBRICANT.
KEY
1000 RPM DRIVE PART NO.
19-0036
540 RPM DRIVE PART NO. DESCRIPTION
19-0035
Complete Gearbox
Casting, Machined (Tapped Holes)
Casting, Machined (Thru Holes)
Assy, Cross Shaft/Gear
Assy, Pinion Shaft/Gear
Bearing Cone
1
19-0031-1
19-0031-1
19-0031-2
19-0035-1
19-0035-2
19-0029-5
19-0029-6
19-0029-7
19-0029-8
19-0029-9
19-0029-10
19-0029-11
19-0016-11
19-0016-5
19-0023-2
19-0002-17
19-0031-5
19-0029-16
2
19-0031-2
3
19-0036-1
4
19-0031-4
5
19-0029-5
6
19-0029-6
Bearing Cup
7
19-0029-7
Bearing Cone
8
19-0029-8
Bearing Cup
9
19-0029-9
Seal 1-3/4"
10
11
12
13
14
15
16
17
19-0029-10
19-0029-11
19-0016-11
19-0016-5
End Plug, Rubber Cover
Retaining Ring, 1.750
Bolt, 3/8-16 x 2.250 SHCS
Plug, ½ NPT
19-0023-2
Bushing, ½ NPT to 1/8 NPT
Plug, Pressure Relief, 5 PSI
Dip Stick
19-0002-17
19-0031-5
19-0029-16
Bearing Cone
Model 8720/8865
-50-
Download from Www.Somanuals.com. All Manuals Search And Download.
AXLE & WHEELS (STANDARD 8720)
(LONG OFFSET)
(SHORT OFFSET)
KEY PART NO.
DESCRIPTION
QTY
KEY PART NO.
DESCRIPTION
QTY
1
75-0211
Hub Assembly
Complete 15,000#
4
17
901-8720-10-1
RH Tandem Wing
Assembly, Less
Hubs
1
2
75-0211-2
75-0211-3
75-0211-4
75-0208-5
75-0208-6
75-0208-7
75-0208-8
75-0208-9
75-0208-10
75-0208-11
75-0208-12
75-0211-1
Seal
1
18
19
901-8720-10-1-4 Nylon Pivot Sleeve
4
2
3
Bearing Cone
Bearing Cup
Bearing Cup
Bearing Cone
Washer
1
901-8720-15
O-Beam Pivot As-
sembly
4
1
5
1
20
21
955-3761
3/16x10" Grease
Hose
2
2
6
1
7
1
955-3762
3/16X16" Grease
Hose
8
Nut
1
22
23
30-0020
75-0276
1/8" NPT Street L
4
4
9
Cotter Pin
Hub Cap
1
10x20 Lock Ring
Rim 1600R20 Used
Military Tire
10
11
12
13
1
Lug Nut - Flanged
Stud Bolt
10
10
1
75-0273
75-0270
22.5x13 Wheel 0"
Offset 425 Used
Truck Tire
4
4
Hub Only w/Races
& Studs
14
15
16
75-0208-13
75-0208-14
901-8720-11-1
Hub Cap Bolt
4
1
1
18X16.1 Wheel
21.5L Implement
Tire
Hub Cap Gasket
LH Tandem Wing
Assembly, Less
Hubs
Model 8720/8865
-51-
Download from Www.Somanuals.com. All Manuals Search And Download.
AXLE & WHEELS, HI-FLOAT PACKAGE
(STANDARD 8865) (OPTIONAL 8720)
KEY PART NO.
DESCRIPTION
QTY
KEY PART NO.
DESCRIPTION
QTY
1
75-0213
Hub Assembly
Complete 20,000#
4
16
901-3771
LH Tandem Wing
Assembly, Less
Hubs
1
2
75-0213-2
75-0213-5
75-0213-10
75-0213-3
75-0213-6
75-0213-12
75-0213-13
75-0213-14
75-0213-7
75-0213-9
75-0213-4
75-0213-1
Seal
1
17
901-3770
RH Tandem Wing
Assembly, Less
Hubs
1
3
Bearing Cone
Bearing Cup
Bearing Cup
Bearing Cone
Washer
1
4
1
5
1
18
19
901-3864-2
901-3773
Nylon Pivot Sleeve
2
2
6
1
O-Beam Pivot As-
sembly
7
1
20
21
881-6311-1.5Z 5/8-11 x 1 ½” GR 8
M.B.
8
8
8
Nut
1
9
Cotter Pin
Hub Cap
1
822-0063-Z
5/8” Split
Lockwasher
10
11
12
13
1
Lug Nut - Flanged
Stud Bolt
10
10
1
22
23
24
901-3772
75-0271
30-0006
Axle Weldment
DW25-26 Wheel
1
4
1
Hub Only w/Races
& Studs
Zerk 1/8" NPT x 90
Degrees
14
15
75-0213-8
Hub Cap Bolt
4
1
25
26
30-0009
30-0008
1/8" NPT Coupler
1/8" NPT Nipple
1
1
75-0213-11
Hub Cap Gasket
Model 8720/8865
-52-
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTS
14
KEY
1
PART NO.
DESCRIPTION
QTY
KEY
PART NO.
56-0009
DESCRIPTION
QTY
56-0030
Dual Light LH w/4-Plug
1
1
7
8
9
Stor-A-Way Plug Holder
Nylon Tie Straps
1
1
1
1a
56-0030-TR Truck Mount Dual Light LH
w/4-Prong
65-0006-5
925-3793
Right / Left Light Mount
Bracket
2
56-0031
Dual Light RH w/4-Plug
56-0031-TR Truck Mount Dual Light
RH w/4-Prong
1
1
2a
10
11
12
13
14
15
56-0001-3
56-0001-4
56-0001-2
56-0001-1
46-0001-62
56-0028
Bezel Blank, Black
#1157 Bulb
1
1
1
1
1
1
3
56-0032
Ag Light Harness w/Mod-
ule
1
Red Lens
Amber Lens
3a
56-0032-1
Replacement Module
w/pigtails & Instructions
AR
Caution Tail Light Decal
Tail Light Converter (Truck
Mount Only)
4
56-0004
56-0005
56-0012
56-0005-1
56-0008
#1232 4-Way Socket 4-Pin
Coil Cable Assembly
7-Contact Plug End Only
4-Hole Plug End Only
Harness Frame Clip
1
1
1
1
1
5
5a
5b
6
Model 8720/8865
-53-
Download from Www.Somanuals.com. All Manuals Search And Download.
This Page Intentionally Blank.
Model 8720/8865
-54-
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS FOR AUTOMATIC CHAIN OILER
WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRES-
SURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO
HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
The automatic chain oiler attachment gives a squirt of clean oil to all roller chains every time that the
spreaders rear gate, hydraulic cylinder is activated. In this way, the spreaders roller chains get oiled
in direct proportion to the number of hydraulic cylinder cycles of the rear gate. This assures ade-
quate lubrication.
New 30 weight oil, which is placed in the reservoir tank mounted on the spreader, is all that is
needed to properly lubricate all roller chains and sprockets. The automatic chain oiler does not use
any oil from the tractors hydraulic system. The hydraulic hose connected to the bottom of the oiler
pump only serves to power the piston in the pump every time that the spreaders rear gate is opened.
Should the oil reservoir tank run dry, pour about a ½ cup of clean 30 weight oil into the tank. Allow
time for the oil to run down into the oiler pump slowly and allow air to escape. After thirty minutes to
one hour has passed, finish filling the reservoir tank. Make sure that all fittings and brackets are tight
when finished filling the tank.
WARNING: HYDRAULIC FLUID ESCAPING UNDER PRESSURE CAN HAVE SUFFI-
CIENT FORCE TO PENETRATE SKIN. KEEP ALL HOSES AND CONNECTIONS IN GOOD
SERVICEABLE CONDITION. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL IN-
JURY OR DEATH.
While running the tractors hydraulics only, open and close the spreaders rear gate several times.
This will cycle the hydraulic cylinder leading to the oiler pump. Keep cycling until oil can be seen in
all of the oil lines leading to the oiler brushes. (If you experience problems priming the oiler pump,
you may need to bleed air out of the hydraulic hose where it is connected to the pump. Crack the fit-
ting until oil comes out then re-tighten.) The hydraulic cylinder that the oiler pump is tied into is dou-
ble acting and must reach 300 PSI of pressure to actuate the pump.
When replacing oiler brushes into brush holders, use regular ½"-20 nuts. Tighten nut finger tight ini-
tially as some adjustment may be needed later. For best results, place brush holders over top of
roller chains and directly on top of sprockets. Adjust brush holders so oiler brushes are pushed
down into the roller chain approximately ½". Carefully tighten up the ½"-20 nuts on the oiler
brushes. DO NOT over tighten as damage to the brush will occur. The plastic threads of the oiler
brush will crack and then break off from the brush body.
IMPORTANT! The 5/32" oil line tubing can only be removed from an oiler brush by pushing in
on the red plastic ring and pulling the tubing out while holding the ring down.
The oiler pump is set at the factory to deliver the maximum amount of oil per cycle. If less oil is de-
sired, loosen the jam nut on the bottom of the pump and screw in the adjusting shaft 1/4" or approxi-
mately 5 turns. It is not recommended to screw the shaft into the bottom of the oiler pump more than
15 turns as this may not allow for proper lubrication of the roller chains.
IMPORTANT! Always use new 30 weight oil. In cold weather, use a SAE 10 or a mixture of
two parts of 30 weight oil to one part diesel fuel.
Model 8720/8865
-55-
Download from Www.Somanuals.com. All Manuals Search And Download.
OIL-KIT
KEY
1
PART NO.
OEM PART NO.
170-4515
576895
576894
2510
DESCRIPTION
952-0001-1-33
952-0001-1-27
952-0001-1-28
952-0001-1-13
952-0001-1-9
952-0001-1-11
952-0001-1-10
952-0001-1-5
952-0001-1-1
952-0001-1-8
952-0001-1-4
952-0001-1-6
952-0001-1-7
952-0001-1-2
952-0001-1-16
952-0001-1-3
952-0001-1-32
952-0001-1-18
952-0001-1-19
952-0001-1-20
952-0001-1-21
952-0001-1-25
813-5020-Z
Holder, Manifold Valve Assembly
Sleeve Nut Brass
2
3
5/32 Brass Ferrule
4
Holder, Manifold Valve
One Way Valve (Schrader Valve)
Bearing, 7/16" Stainless
Screen Flat Oiler .906 Dia
Spring, Oiler
5
1012
6
3520
7
1019
8
1004
9
1001-6-B
2-022-N552-90
1033
Oiler Body 6 Port Black
O Ring, Oiler Piston 2-022 90 Dur
Piston, 2 Groove Alum, Short
Washer, Rubber Lube Minder
O Ring, Adj End Cap Plunger
Adj End Cap Oil Black
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
2-026-N552-90
2-113-N674-70
21999-0224
6010
½-20 Jam Nut
4511
Plunger, Brass Adj End Cap
1/8" Hex Head Pipe Plug
Reservoir Two Quart Tank
Hydraulic Hose Assembly Meyer Mfg.
Tubing 5/8" ID Clear Polybraid
Tubing 5/32" Nylon (Feet)
Brush Assembly No 5/32 Insert
½ 20 Plated Nut
2107001U
2550
M-4555
7010
7012
4514
952-0001-1-17
952-0001-1-14
955-3803
2016
2511
Bracket Oiler Mtg Pump
5/32 Push In Insert (Nycoil)
BM Pipe Tee 3/8 x 3/8 x 3/8
1" Hose Clamp
952-0001-1-30
952-0001-1-31
08-0050
4517
U-Bolt Assembly # 9
5-16” Loom Clamp
33-8000-7
Brush Holder
952-0001-3
Auger Chain Brush Holder
120/140 Chain Brush Holder
Oiler Tank Mount Plate
Oiler Body Pump Assy, Complete
952-0001-8
952-0001-5
952-0001-1-36
170-000-6
Model 8720/8865
-57-
Download from Www.Somanuals.com. All Manuals Search And Download.
MEYER INDUSTRIAL SPREADER
“TROUBLE SHOOTING”
SYMPTOM
Augers shake or chatter
PROBLEM
SOLUTION
Lubricate roller chains
Tighten roller chains
Replace sprockets/chains
Load auger trough w/manure
Stiff roller chains - dry
Loose roller chains
Worn sprockets/chain
Dry auger trough
AUGERS
Augers wobble/lift up &
down
Worn auger shaft bushings
Worn auger hold down nylon
bearings
Replace auger shaft bushings
Replace auger hold down
nylon bearings
Will not lift
No hydraulic supply
Froze tight w/build-up
Lodged foreign object/dirty
Supply hydraulic power
Thaw frozen build-up
Remove foreign object/clean
FLOW
CONTROL
GATE
Will not close/seal
Sticks/binds
Dirty/dry slide guides
Worn slide guides
Worn out slide guide polyslick Replace slide guide polyslick
Clean/lubricate slide guides
Replace slide guides
Clunking sounds
Excessive oil use
Gears/bearings wearing
Low oil or fluid gear grease
Replace gears/bearings
Fill with #80-#90 wt. Gear
lube oil or fluid gear grease
GEAR
BOXES
Worn out oil seals
Replace oil seals
Dry manure & twine wrapping Clean & remove build-up at
seal areas
Gear damage
Dirty/build-up
High speed/full load start-up
Worn out gears
Too slow spinner RPM’s
Slow start-up, fill with oil
Replace gears
Operate spreader at recom-
mended RPM’s
MATERIAL
GUIDES
PTO SHAFT
Whips/shakes
Over extended or bent PTO
Adjust tractor drawbar length
- See Page 8
Replace center shaft
Vibrates up & down
Worn Universal Joints
Spreader center shaft bent
Lack of lubrication/used
Lubricate joints daily replace
joint
Lubricate/align/tighten
Excessive chain wear
Roller chain breakage
Lack of lubrication
Out of alignment/loose
ROLLER
CHAINS AND
SPROCKETS
Loose roller chain
Worn sprockets
Tighten roller chains
Replace sprockets
Sprocket teeth tipped over Worn roller chain
Bad roller bearings
Spinners turn hard/squeak Bad lower spinner bearings
Replace roller chain
Replace bearings
Replace lower spinner
bearings
SPINNERS
PADDLES/
TEETH
Shake at high RPM’s
(excessive vibration)
Spinner bent/out of balance
Straighten/balance/replace
spinner
Excessive paddle damage Wobbled out lower spinner
shaft
Replace or reweld lower
spinner shaft
Too slow spinner RPM’s
Lodging of manure
Operate spreader at recom-
mended RPM’s
Adjust material guides
Straighten/replace paddles
Spreading foreign objects
Avoid loading foreign objects
Model 8720/8865
-58-
Download from Www.Somanuals.com. All Manuals Search And Download.
MEYER EQUIPMENT WHEEL TORQUE
BOLT/STUD
SIZE
SOCKET
SIZE
PRESS FORMED
WHEEL CENTER
BOLT
TYPE
HEAVY DUTY
WHEEL CENTER
½
3/4
7/8
80 ft lbs
80 ft lbs
100 ft lbs
Lug Bolt
Lug Bolt
85 ft lbs
120 ft lbs
160 ft lbs
9/16
5/8
15/16 / 1-1/16
Bevel or Flange
Nut
3/4
1-1/8 / 1 ½
Flange Nut
378 ft lbs
8720/8865 SPREADER W/ BRAKES TIRE WHEEL TORQUE
• Clean adjoining surfaces
• Start nuts to bring wheel and brake drum flush to hub mounting surface.
• Avoid brake drum and/or wheel binding on hub.
• Install remaining wheel nuts. Torque to 50 ft-lbs. Then re-torque to 450-500 ft-lbs
(22mm) or 265 ft-lbs (3/4”).
• Re-torque wheel nuts after 50-100 miles.
• Check wheel nut torque every 10,000 miles and re-torque as necessary.
CAUTION: THESE INSTRUCTIONS ARE NOT COMPLETE. READ AND FOLLOW ALL PROCEDURES
IN USER’S GUIDE TO WHEELS AND RIMS BY “THE MAINTENANCE COUNCIL” #T0410. IF YOU HAVE
QUESTIONS CALL WALTHER ENG. & MFG. COMPANY INC. (937)847-2700.
TIRE INFLATION
TIRE SIZE
11L-15
PLY
PSI
36
36
52
44
36
32
44
75
75
28
8
12.5L-15
12.5L-15
14L-16
8
12
12
16.5L-16
19LX16.1
21.5L-16.1
11R/22.5
425/65X22.5
28L-26
10
10
18
used truck
used truck
16
Model 8720/8865
-60-
Download from Www.Somanuals.com. All Manuals Search And Download.
MEYER INDUSTRIAL SPREADER
DIMENSIONS & SPECIFICATIONS
Industrial 8720
Trailer Type
w/ 21.5 Tires “
Industrial 8720
Truck Mount
w/ Mount Brkts.
Industrial 8856
Trailer Type w/
28L x 26 Tires
Industrial 8865
Truck Mount w/
Mount Brkts.
CAPACITY
Bushels Heaped
Gallons/Cu.ft. (Struck)
Cu. Yards. (struck)
DIMENSIONS
720
720
865
865
3500/468
17.33 cu. yards
3500/468
17.33 cu. yards
4200/562
20.8 cu. yards
4200/562
20.8 cu. yards
Overall Length
26’6”
16’8”
20’10” w/ Hyd
Motor
29’10”
24’2” w/ Hyd
Motor
Inside Tank Length
Loading Height
16’8”
20’
20’
87” w/21.5 or
425/65
91” w/16.00X20
68”Plus Truck
Height
88” w/28L x 26
68” Plus Truck
Height
Overall Height -
Top of Splash Guard
96” w/21.5 or
425/65
100” w/16.00X20
77”Plus Truck
Height
97” w/28L x 26
Tires
77” Plus Truck
Height
Overall Width (std. Axle)
Outside Tires
118” w/21.5L
114” w/16.00X20
101”
N/A
101”
Overall Width w/high
Floatation axle pkg.
141” w/28L x 26
141” w/ 28L x 26
Tires
Top Inside Tank Width
SPECIFICATIONS
Total Weight
101”
101”
101”
101”
13,720#
35,200#
23”
9,400#
18,020#
38,000#
23”
10,700#
38,000#
23”
Maximum Load Net (Lbs.)
Lower Auger Diameter
35,200#
23”
Lower Auger Flighting Thick-
ness
3/8” Sectional
3/8” Sectional
3/8” Sectional
3/8” Sectional
Independent Lower Auger
Shear Hub Sprockets
Standard
Standard
Standard
Standard
3rd Auger (solid material)
Drive - PTO-RPM
Standard - 16”
Standard -16”
Standard - 16”
Standard - 16”
1000 RPM Con-
stant Velocity 1
3/8-21 spline
PTO - Direct Std. 1000 RPM Con-
Hydrostatic-Opt. stant Velocity 1
3/4-20 Spline
PTO - Direct Std.
Hydrostatic-Opt.
Drive Line Protection
Overrunning Cut
Out Clutch w/
Shear Bolt Au-
gers
Cut Out Clutch w/ Overrunning Cut
Cut Out Clutch w/
Shear Bolt (Pto
Version)
Shear Bolt (Pto
Version)
Out Clutch w/
Shear Bolt Au-
gers
Roller Chain Drive
Roller Chain Auto Oiler
Expeller Speed (RPM)
Expeller Diameter
TANK CONSTRUCTION
Material
80-120-140
Standard
716 RPM
30”
80-120-140
Standard
716 RPM
30”
80-120-140
Standard
716 RPM
30”
80-120-140
Standard
716 RPM
30”
Copper Bearing
Steel
Copper Bearing
Steel
Copper Bearing
Steel
Copper Bearing
Steel
Thickness - Auger Troughs
Thickness - Tank Sides
1/4”
1/4”
1/4”
1/4”
3/16”
3/16”
3/16”
3/16”
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
Model 8720/8865
-61-
Download from Www.Somanuals.com. All Manuals Search And Download.
MEYER INDUSTRIAL SPREADER
DIMENSIONS & SPECIFICATIONS
Frame Construction
Door Opening
Heavy 8”
Channel
Heavy 8”
Channel
Heavy 8”
Channel
Heavy 8”
Channel
32” x 53”
32” x 53”
32” x 53”
N/A
32” x 53”
Standard Axle Spindle Diame- Standard Tan-
ter
dem 3 ½”“
Sleeved
High Floatation Axle Spindle
Diameter
Optional Tandem
4 ½”“ Sleeved
Standard
Tandem 4 ½”“
Sleeved
Standard Axle Hub Size
10 Bolt-15,000#
N/A
High Floatation Axle Hub Size 10 Bolt-20,000#
(opt.)
10 bolt-20,000#
(std.)
Splash Shields-Standard
Lights w/hookup cord
45 Front/45 Rear 45 Front/45 Rear 45 Front/45 Rear 45 Front/45 Rear
Standard
Standard
Standard
Standard
Tractor Requirement PTO HP 130 HP Tractor
(Min.)
160 HP Tractor
OPTIONS
1000 RPM 1 3/8”-21 Spline
1000 RPM 1 3/4”-20 Spline
Hydraulic Lid
Standard
Optional
Optional
Optional
Optional
Standard
Optional
Optional
Standard
Optional
Optional
Optional
Optional
Poultry Litter Package
High Floatation Axle Package Optional
Hyd. Brakes-HF axle only
Optional (2 or 4
wheel)
Optional (2 or 4
wheel)
Safety Chain
Optional
Optional
PTO - Direct Std.
Hydrostatic - Opt
PTO - Direct Std.
Hydrostatic - Opt
Truck Mount Drive Options
Hyd. Drive Expellers W/vari-
able auger speeds
N/A
Optional
N/A
Optional
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
Manufactured by:
Meyer Mfg. Corp.
County Hwy. A West
P.O. Box 405
Dorchester, Wisconsin 54425-0405
Phone 715-654-5132 · FAX 715-654-5513
1-800-325-9103
E-mail: sales @meyermfg.com
Farm Equipment Buyers Trust the Name Meyer!
Model 8720/8865
-62-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 8720/8865
-63-
Download from Www.Somanuals.com. All Manuals Search And Download.
C
Download from Www.Somanuals.com. All Manuals Search And Download.
|
