METROLOGIC INSTRUMENTS, INC.
MS3580 QuantumT™
Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Introduction
Product Overview............................................................................................. 1
Scanner and Accessories................................................................................. 2
Scanner Components....................................................................................... 4
Caution and Serial Number Labels................................................................... 5
Cable Removal................................................................................................. 5
Maintenance..................................................................................................... 5
Mounting Specifications and Stand Assembly.................................................. 6
Installation
RS232, RS232 TTL, Light Pen or Laser Emulation.......................................... 8
IBM 46xx or OCIA ............................................................................................ 9
Keyboard Wedge............................................................................................ 10
Stand-Alone Keyboard Wedge....................................................................... 11
Full Speed or Low Speed USB (Integrated) ................................................... 12
Scanner Operation
Configurable Primary and Secondary Scan Pattern Modes ........................... 13
Configurable Button Functions ....................................................................... 13
Indicators
Audible ....................................................................................................... 19
Visual ......................................................................................................... 20
Failure ........................................................................................................ 21
Depth of Field Specifications
Normal Scan Zone ..................................................................................... 22
Reduced Scan Zone................................................................................... 23
Depth of Field by Bar Code Element Width
Normal Scan Zone ..................................................................................... 24
Reduced Scan Zone................................................................................... 25
IR Activation Range........................................................................................ 26
Troubleshooting Guide ....................................................................................... 27
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Design Specifications ......................................................................................... 31
Applications and Protocols ................................................................................. 33
Default Settings - Communication Parameters................................................... 34
Upgrading the Flash ROM Firmware.................................................................. 39
Scanner and Cable Terminations
Scanner Pinout Connections.......................................................................... 40
Cable Connector Configurations (Host End) .................................................. 42
Laser and Product Safety................................................................................... 44
Limited Warranty ................................................................................................ 46
Patents ............................................................................................................... 47
Index .................................................................................................................. 48
Contact Information and Office Locations........................................................... 50
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
The QuantumT™ is a hands-free, omnidirectional bar code scanner with optional
single-line scanning capabilities. It utilizes the powerful Metrologic QuantumE™
scan engine to provide an outstanding scan performance on all standard 1D
barcode symbologies, including RSS. This fully enclosed scanner includes large
easily visible LEDs and a rugged protective boot with an adjustable stand. The
QuantumT can be mounted to a countertop, wall or be left free standing for
handheld scanning.
Key Product Features
•
•
•
•
•
Fully Automatic Scanning Operation
Single-Line Mode for Menu Reading
Custom Configurable Scan Pattern
User-Replaceable Single Cable Interface to Host (PowerLink Compatible)
Decoding of All Standard 1D, RSS-14, RSS Limited and Expanded RSS
Bar Codes
•
•
•
•
•
•
7 Beeper Tones
Configurable Depth of Field
Flash - Upgradeable Firmware
OPOS and JPOS System Compatible
CodeGate®
Sunrise 2005 Compliant
QUANTUMT
INTERFACE
OCIA and RS232 Transmit/Receive
IBM 46xx and Full RS232
MS3580-9
MS3580-11
RS232 Low Speed USB,
Keyboard Emulation Mode or Serial Emulation Mode*
MS3580-38
MS3580-40
MS3580-41
Full Speed USB
RS232/Light Pen Emulation
Keyboard Wedge, Stand-Alone Keyboard and
RS232 Transmit/Receive
MS3580-47
MS3580-104
RS232 TTL, Laser Emulation
* Configurable for Keyboard Emulation Mode or Serial Emulation Mode.
Default setting is Keyboard Emulation Mode.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Scanner and Accessories
BASIC KIT COMPONENTS
Part No.
MS3580
Description
QuantumT Omni \ Single-Line Scanner
QuantumT Omni \ Single-Line Scanner
Installation and User’s Guide *
00-02026
00-02407
MetroSelect® Configuration Guide *
OPTIONAL ACCESSORIES
Part No.
Description
AC to DC Power Transformer - Regulated 5.2VDC @ 650 mA output.
45-45593
120V United States and Canada
220V-240V Continental European
220V-240V United Kingdom
220V-240V Australia
45-45591
45-45592
46-46803
46-46983
220V-240V China
RS232 PowerLink Cable with Built in Power Jack
2.1 m (7 ft.) straight cord, short strain relief
54-54000x -3
MVC**
Metrologic Voltage Converter Cable ±12VDC to +5.2VDC
** Contact a Metrologic customer service representative for additional
information on the MVC cable series and the host connections available.
Other items may be ordered for the specific protocol being used. To order additional items,
contact the dealer, distributor or call Metrologic’s customer service department at
1-800-436-3876.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Scanner and Accessories
OPTIONAL ACCESSORIES
Part No.
Description
Keyboard Wedge PowerLink Cable
2.1 m (7 ft.) straight cord, short strain relief
54-54002x-3
Stand Alone Keyboard PowerLink Cable
2.1 m (7 ft.) straight cord, short strain relief
54-54020x-3
USB Full Speed Cable, Locking Plus-Power™ Type A
3 m (10 ft.) straight cord, short strain relief
54-54213x-N-3
USB Full Speed Cable, Locking Plus-Power™ Type A
5 m (17 ft.) straight cord, short strain relief
54-54214x-N-3
This cable is for use with full speed
USB (-40) interface only.
USB Low Speed Communication Cable, Type A
2.8 m (9.2 ft.) straight cord, short strain relief
54-54235x-N-3
54-54249x-N-3
Communication Cable, Host End Not Terminated
203 mm (8") straight cord, short strain relief
46-00288
46-00289
Flex Stand (3")
Flex Stand (6")
Other items may be ordered for the specific protocol being used. To order additional items,
contact the dealer, distributor or call Metrologic’s customer service department at
1-800-436-3876.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Scanner Components
Figure 1. Scanner Components
ITEM NO.
DESCRIPTION
Red Output Window (Laser Aperture)
Pin Hole for Cable Release
10-Pin RJ45, Female Socket
Speaker
1
2
3
4
5
6
Blue and White LED Indicators
Button
Protective Boot and Stand Connection
Never remove the protective boot from the MS3580.
Removing the protective boot will expose electrical
components of the scanner that are highly susceptible to
electrostatic discharge (ESD).
7
8
Pedestal Stand
The type of stand provided is dependent on the specific
MS3540 kit purchased.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Caution and Serial Number Labels
Figure 2. Labeling Example
Cable Removal
1. Locate the small ‘pin-hole’ on the side of
the QuantumT near the cable.
2. Bend an ordinary paperclip into the shape
shown.
3. Insert the paperclip (or other small metallic
pin) into the small ‘pin-hole’.
4. You will hear a faint ‘click’ when the cable
lock is released. Pull gently on the strain-
relief of the PowerLink cable to remove it
from the scanner.
Figure 3. Cable Release
Maintenance
Smudges and dirt can interfere with the proper scanning of a bar code.
Therefore, the output window will need occasional cleaning.
1. Spray glass cleaner onto a lint free, non-abrasive cleaning cloth.
2. Gently wipe the scanner window.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Mounting Specifications and Stand Assembly
Pedestal Stand
Figure 4. Pedestal Stand Assembly
Optional Flex Stand
Figure 5. Assembly Components for Optional Flex Stand
Item
Description
MS3580, QuantumT
Pivot Cylinder
Bearing Plate
Pole Mount Adapter
Flexible Shaft Cover*
Qty.
1
1
1
1
Item
6
7
8
9
Description
Flexible Shaft*
Base Plate Cover
#8 x 1.00" Wood Screw
Base Plate
Qty
1
1
4
1
1
2
3
4
5
1
10
Cable (Not Shown)
1
* Length of the Flexible Shaft and Shaft Cover are Kit Dependent
Kit Number
46-00288
46-00289
Length of Flexible Shaft and Flexible Shaft Cover
3 inches
6 inches
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Mounting Specifications and Stand Assembly
Optional Flex Stand
Figure 6. Mounting Hole Detail for the Flex Stand Base Plate (Optional)
Figure 7. Assembling the Optional Flex Stand
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
RS232, RS232 TTL, Light Pen or Laser Emulation
1. Turn off the host device.
2. Plug the male 10-pin RJ45 end
of the PowerLink cable into the
10-pin socket on the MS3580.
3. Connect the 9-pin female end of the
PowerLink cable to the host device.
4. Plug the external power supply into the
power jack on the PowerLink cable.
Check the AC input requirements
of the power supply to make sure
the voltage matches the AC outlet.
The outlet must be located near
the equipment and be easily
accessible.
5. Connect AC power to the transformer.
6. Turn on the host device.
Figure 8.
When the scanner first receives power, the blue LED will turn on; the
scanner will simultaneously emit a beep and flash the white LED.
Plugging the scanner into the serial port of the PC does not guarantee
that scanned information will appear at the PC. A software driver and
correct configuration setting are also required for proper
communication to occur.
The MS3580-104 leaves the factory with the Laser Emulation
enabled. If the Recall Defaults bar code is scanned while
reconfiguring the scanner, laser emulation will no longer be enabled.
Scan the Laser Emulation barcode in Section J: Laser Emulation of
the MetroSelect Configuration Guide to re-enable the laser emulation
interface. This feature is only supported for MS3580-104 models.
Caution
To maintain compliance with applicable standards, all circuits connected to the scanner
must meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC
60950.
To maintain compliance with standard CSA C22.2 No. 60950/UL 60950 and norm
EN/IEC 60950, the power source should meet applicable performance requirements for
a limited power source.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
IBM 46xx or OCIA
1. Turn off the host device.
2. Plug the male 10-pin RJ45 end
of the MVC cable into the
10-pin socket on the MS3580.
3. Connect the other end of the MVC
cable to the host device.
4. Turn on the host device.
Figure 9.
When the scanner first receives power, the blue LED will turn on; the
scanner will simultaneously emit a beep and flash the white LED.
Plugging the scanner into the serial port of the PC does not
guarantee that scanned information will appear at the PC. A software
driver and correct configuration setting are also required for proper
communication to occur.
Caution:
To maintain compliance with applicable standards, all circuits connected to the scanner
must meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC
60950.
To maintain compliance with standard CSA C22.2 No. 60950/UL 60950 and norm
EN/IEC 60950, the power source should meet applicable performance requirements for
a limited power source.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Keyboard Wedge
1. Turn off the host device.
2. Plug the male 10-pin RJ45 end of the
PowerLink cable into the 10-pin
socket on the MS3580.
3. Disconnect the keyboard from the
host device.
4. Connect the “Y” end of the PowerLink
cable to the keyboard and the
keyboard port on the host PC. If
necessary use the male/female
adapter cable supplied with the
scanner for proper connections.
5. Plug the external power supply into the
power jack on the PowerLink cable.
Check the AC input requirements
of the power supply to make sure
the voltage matches the AC
outlet. The outlet must be
located near the equipment and
be easily accessible.
Figure 10.
6. Connect AC power to the transformer.
7. Turn on the host device.
When the scanner first receives power, the blue LED will turn on; the
scanner will simultaneously emit a beep and flash the white LED.
Powering the MS3580 directly from the host device can sometimes
cause interference with the operation of the scanner or the computer.
Not all computers supply the same current through the keyboard port.
For this reason, Metrologic recommends using an external power
supply. For additional information contact a Metrologic customer
service representative.
Caution:
To maintain compliance with applicable standards, all circuits connected to the scanner
must meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC
60950.
To maintain compliance with standard CSA C22.2 No. 60950/UL 60950 and norm
EN/IEC 60950, the power source should meet applicable performance requirements for
a limited power source.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Stand-Alone Keyboard
1. Turn off the host device.
2. Plug the male 10-pin RJ45 end
of the PowerLink cable into the
10-pin socket on the MS3580.
3. Connect the other end of the
PowerLink cable to the keyboard
port on the host device.
4. Plug the external power supply into
the power jack on the PowerLink
cable.
Check the AC input
requirements of the power
supply to make sure the
voltage matches the AC
outlet. The outlet must be
located near the equipment
and be easily accessible.
5. Connect AC power to the transformer.
6. Turn on the host device.
Figure 11.
When the scanner first receives power, the blue LED will turn on; the
scanner will simultaneously emit a beep and flash the white LED.
Powering the MS3580 directly from the host device can sometimes
cause interference with the operation of the scanner or the computer.
Not all computers supply the same current through the keyboard port.
For this reason, Metrologic recommends using an external power
supply. For additional information contact a Metrologic customer
service representative.
Caution:
To maintain compliance with applicable standards, all circuits connected to the scanner
must meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC
60950.
To maintain compliance with standard CSA C22.2 No. 60950/UL 60950 and norm
EN/IEC 60950, the power source should meet applicable performance requirements for
a limited power source.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Full Speed or Low Speed USB
1. Turn off the host device.
2. Plug the male 10-pin RJ45 end of
the USB cable into the 10-pin
socket on the MS3580.
3. Plug the other end of the USB
interface cable into the host
device’s USB port.
4. Turn on the host device.
Figure 12.
When the scanner first receives power, the blue LED will turn on; the
scanner will simultaneously emit a beep and flash the white LED.
As a default, the MS3580-38 leaves the factory with USB Keyboard
Emulation Mode enabled.
For information on configuring the MS3580-38 for USB Serial
Emulation Mode, please refer to Section P: Low Speed USB in the
MetroSelect Configuration Guide (MLPN 00-02407).
Plugging the scanner into the USB port of the PC does not guarantee
that scanned information will appear at the PC. A software driver and
correct configuration setting are also required for proper
communication to occur.
Caution:
To maintain compliance with applicable standards, all circuits connected to the scanner
must meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC
60950.
To maintain compliance with standard CSA C22.2 No. 60950/UL 60950 and norm
EN/IEC 60950, the power source should meet applicable performance requirements for
a limited power source.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Configurable Primary and Secondary Scan Pattern Modes
There are two configurable scan pattern modes available with the MS3580.
•
The primary scan pattern mode is the default scan pattern active when the
scanner starts.
•
The secondary scan pattern mode is activated by pressing the button
located on the side of the scanner. This mode is also referred to as the
button mode. For additional information on Quantum’s button modes and an
example of each, please refer to Configurable Button Functions below.
The scanner returns to the primary scan pattern mode after a double
click of the button or if the unit has not scanned a bar code for the
duration of a pre-configured time limit.
Each pattern mode can be configured to use one of three scan patterns listed
below. Please refer to the MetroSelect Configuration Guide for information on
changing the default scan pattern settings.
•
•
•
all scan lines on (omnidirectional reading)
single-line (menu reading)
horizontal raster
If CodeGate is enabled, it will apply to the secondary pattern mode
when scanning. For detailed information on CodeGate and the button
refer to the Configurable Button Functions.
Configurable Button Functions
The button on the side of the MS3580 can be configured to function in one of
four modes.
•
•
•
•
Button Click Mode, with CodeGate Enabled (Default)
Button Click Mode, with CodeGate Disabled
Button Hold Mode, with CodeGate Enabled
Button Hold Mode, with CodeGate Disabled
The following pages include examples of how the button will function when the
unit has been configured to operate in each of the four button modes.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Configurable Button Functions
SECONDARY SCAN PATTERN
BUTTON CLICK MODE WITH CODEGATE ENABLED
For illustration purposes the unit’s primary scan pattern has been set to
all scan lines (omnidirectional reading) and the secondary pattern has
been set to single-line (menu reading) with a 5 second button click
timeout configured.
1. The primary scan pattern is active when the
scanner starts.
2. To activate the secondary scan pattern,
press and release the button.
3. To decode and transmit the bar code,
press and release the button.
The scanner will beep once.
4. To reactivate the primary scan pattern,
double click the button or after 5-seconds
of no-scanning the unit will automatically
reactivate the primary pattern.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Configurable Button Functions
SECONDARY SCAN PATTERN
BUTTON CLICK MODE WITH CODEGATE DISABLED
For illustration purposes the unit’s primary scan pattern has been set to
all scan lines (omnidirectional reading) and the secondary pattern has
been set to single-line (menu reading) with a 5 second button click
timeout configured.
1. The primary scan pattern is active when the
scanner starts.
2. To activate the secondary scan pattern,
press and release the button.
3. The unit will beep once as it decodes and
transmits the bar code.
4. To reactivate the primary scan pattern,
double click the button or after 5-seconds
of no-scanning the unit will automatically
reactivate the primary pattern.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Configurable Button Functions
SECONDARY SCAN PATTERN
BUTTON HOLD MODE WITH CODEGATE ENABLED
For illustration purposes the unit’s* primary scan pattern has been set to
all scan lines (omnidirectional reading) and the secondary pattern has
been set to single-line (menu reading) with a 5 second button click
timeout configured.
1. The primary scan pattern is active when the
scanner starts.
2. To activate the secondary scan pattern,
press and hold the button.
3. To scan the bar code, align the laser line
over the bar code while continuing to hold
down the button.
4. To transmit the bar code, release the
button. The scanner will beep once.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Configurable Button Functions
5. To scan and transmit additional bar codes,
repeat steps 2 through 4.
6. The primary scan pattern will automatically
reactivate after the button is released and no
bar code is present in the scan field.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Configurable Button Functions
SECONDARY SCAN PATTERN
BUTTON HOLD MODE WITH CODEGATE DISABLED
For illustration purposes the unit’s* primary scan pattern has been set to
all scan lines (omnidirectional reading) and the secondary pattern has
been set to single-line (menu reading) with a 5 second button click
timeout configured.
1. The primary scan pattern is active when the
scanner starts.
2. To activate the secondary scan pattern,
press and hold the button.
3. To scan and transmit the bar code, align the
laser line over the bar code while continuing
to hold down the button. The scanner will
beep once to indicate the bar code has been
scanned and transmitted.
4. The primary scan pattern will automatically
reactivate after the button is released and no
bar code is present in the scan field.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Audible Indicators
When the MS3580 is in operation, it provides audible feedback to indicate the
status of the scanner. Eight settings are available for the tone of the beep
(normal, 6 alternate tones and no tone). For instructions on how to change the
tone of the beeper, refer to the MetroSelect Configuration Guide (00-02407).
One Beep
When the scanner first receives power the white LED will flash, the blue LED
will turn on and the scanner will beep once (the white LED will remain on for
the duration of the beep). The scanner is now ready to scan.
When the scanner successfully reads a bar code, the white LED will flash and
the scanner will emit a beep (if configured to do so). If the scanner does not
beep once and the white light does not flash, then the bar code has not been
successfully read.
Razzberry Tone
This is a failure indicator. Refer to Failure Mode Indicators on page 21.
Three Beeps - during operation
When placing the scanner in configuration mode, the white LED will flash
while the scanner simultaneously beeps three times. The white and blue
LEDs will continue to flash until the unit exits configuration mode. Upon exiting
configuration mode, the scanner will beep three times and the white LED will
stop flashing.
When configured, 3 beeps can also indicate a communications timeout during
normal scanning mode.
When using one-code-configuring, the scanner will beep three times: the
current selected tone, followed by a short pause, a high tone and a low tone.
This tells the user that the single configuration bar code has successfully
configured the scanner.
Three Beeps - on power up
This is a failure indicator. Refer to Failure Mode Indicators on page 21.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Visual Indicators
The QuantumT is equipped with a blue and white LED that indicates the
scanner’s state and the status of the current scan when the unit is in operation.
Figure 13. Speaker Location and LED Location
No LEDs
The LEDs will not be illuminated if the scanner is not receiving power from the
host or transformer. They are also not illuminated when the laser is turned off
for any reason.
Steady Blue
When the laser is active, the blue LED is illuminated. The blue LED will remain
illuminated until the laser is deactivated.
Steady Blue and Single White Flash
When the scanner successfully reads a bar code, the white LED will flash and
the scanner will beep once. If the white LED does not flash or the scanner
does not beep once, then the bar code has not been successfully read.
Steady White and Blue
After a successful scan, the scanner transmits the data to the host device.
Some communication modes require that the host inform the scanner when
data is ready to be received. If the host is not ready to accept the information,
the scanner’s white LED will remain on until the data can be transmitted.
Alternating Blue and White Flashes
This indicates the scanner is in configuration mode. A razzberry tone indicates
that an invalid bar code has been scanned in this mode.
Steady White, Blue Off
This indicates the scanner may be waiting for communication from the host.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Failure Mode Indicators
Flashing Blue and One Razzberry Tone
This indicates that the scanner has experienced a laser subsystem failure.
Return the unit to an authorized service center for repair.
Flashing Blue and White and Two Razzberry Tones
This indicates that the scanner has experienced a motor failure. Return the unit
to an authorized service center for repair.
Continuous Razzberry Tone with Both LEDs Off
If, upon power up, the scanner emits a continuous razzberry tone, then the
scanner has an electronic failure. Return the unit to an authorized service
center for repair.
Three Beeps - On Power Up
If the scanner beeps 3 times on power up, then the nonvolatile memory that
holds the scanner configuration has failed. Return the unit to an authorized
service center for repair.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Depth of Field Specifications*
Normal Scan Zone
Specifications are based on a 0.33 mm (13 mil) bar code.
Figure 14. MS3580† Normal Depth of Field
* All specifications are subject to change without notice.
†
MS3580 shown with pedestal stand.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Depth of Field Specifications*
Reduced Scan Zone
Specifications are based on a 0.33 mm (13 mil) bar code.
Figure 15. MS3580† Reduced Depth of Field
* All specifications are subject to change without notice.
†
MS3580 shown with pedestal stand.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Depth of Field by Bar Code Element Width*
Normal Scan Zone
MINIMUM BAR CODE ELEMENT WIDTH
A
B
C
D
E
F
mm
.13
5.2
.15
5.7
.19
7.5
.25
10
.33
13
.66
26
mils
Figure 16. Normal Scan Zone by Bar Code Element Width
* All specifications are subject to change without notice.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Depth of Field by Bar Code Element Width*
Reduced Scan Zone
MINIMUM BAR CODE ELEMENT WIDTH
A
B
C
D
E
F
mm
.13
5.2
.15
5.7
.19
7.5
.25
10
.33
13
.66
26
mils
Figure 17. Reduced Scan Zone by Bar Code Element Width
* All specifications are subject to change without notice.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
IR Activation Range*
QuantumT‘s default power save mode† is Laser OFF. This power save mode
turns the laser off after a configured period of non-use. Any movement detected
by the IR in the activation area will cause the scanner to exit power save mode.
The laser will automatically turn back on preparing the scanner for bar code
recognition, decoding and transmission.
Figure 18. Normal IR Activation Range
* All specifications are subject to change without notice.
†
Refer to the MetroSelect Configuration Guide (00-02407) for additional information on
configurable power save modes.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
The following guide is for reference purposes only. Contact a Metrologic
representative at 1-800-ID-METRO or 1-800-436-3876 to preserve the limited
warranty terms on page 46.
Symptoms
Possible Cause(s)
Solution
All Interfaces
Check the transformer, outlet
and power strip. Make sure the
cable is plugged into the
scanner.
The unit has no
LEDs, beeper
or motor spin.
No power is being
supplied to the
scanner.
Some host systems cannot
supply enough current to power
the MS3580. Use the power
supply included with the
scanner.
The unit has no
LEDs and / or
beeper.
No power is being
supplied to the
scanner from host.
There are
multiple scans
upon
presentation of
code.
The same symbol
timeout is set too
short.
Adjust the same symbol timeout
for a longer time increment.
The beeper is disabled. Enable the beeper.
The unit powers
up but does not
beep.
No tone is selected.
Select a tone.
UPC/EAN, Code 39, Interleaved
2 of 5, Code 93, Code 128 and
Codabar are enabled by default.
Verify that the type of bar code
being read has been selected
The unit is trying to
scan a particular
symbology that is not
enabled.
The unit powers
up but does not
scan and/or
beep.
The scanner has been
configured for a
Verify that the bar code that is
being scanned falls into the
criteria.
character length lock,
or a minimum length
and bar code being
scanned does not
satisfy the configured
criteria.
Typical of Non-UPC/EAN codes.
The scanner defaults to a
minimum of 4 character bar
code.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Symptoms
Possible Cause(s)
Solution
All Interfaces
The unit scans
a bar code, but
locks up after
the first scan
(the white LED
stays on).
If the scanner is setup to support
ACK/NAK, RTS/CTS,
XON/XOFF or D/E, verify that
the host cable and host are
supporting the handshaking
properly.
The scanner is
configured to support
some form of host
handshaking but is not
receiving the signal.
Verify that the scanner’s data
format matches the format
required by the host.
Make sure that the scanner is
connected to the proper host
port.
The unit scans
but the data
transmitted to
the host is
The scanner’s data
format does not match
the host system
requirements.
incorrect.
The type of printer and/or the
printer settings could be the
problem.
The print quality of the
bar code is suspect.
Check the print mode or change
the printer settings. For
example, change to econo mode
or high speed.
The aspect ratio of the
bar code is out of
tolerance.
Scanner beeps
at some bar
codes and NOT
for others of the
same bar code
symbology.
The bar code may
have been printed
incorrectly.
Check if it is a check digit,
character or border problem.
The scanner is not
configured correctly
for the type of bar
code.
Check if check digits are set
properly.
The minimum symbol
length setting does not Check if the correct minimum
work with the bar
code.
symbol length is set.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Symptoms
Possible Cause(s)
Solution
All Interfaces
During power
up the unit
beeps 3 times.
There is a non-volatile
RAM failure.
Contact a Metrologic service
representative.
During power
up the unit
razzes
There is a RAM or
ROM failure.
Contact a Metrologic service
representative.
continuously.
During power
up the unit
razzes once
and the blue
LED flashes.
Contact a Metrologic service
representative.
There is a VLD failure.
During power
up the unit
razzes twice
and both LEDs
flash.
There is a scanner
motor failure.
Contact a Metrologic service
representative.
RS232 Only
The com port at the
host is not working or
is not configured
properly.
The unit powers
up OK and
scans OK but
does not
communicate
properly to the
host.
Check to make sure that the
baud rate and parity of the
scanner and the communication
port match and that the program
is looking for RS232 data.
The cable is not
connected to the
proper com port.
The com port is not
operating properly.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Symptoms
Possible Cause(s)
Solution
RS232 Only
The host is
The scanner and host
may not be configured
for the same interface.
Check that the scanner and the
host are configured for the same
interface.
receiving data
but the data does
not look correct.
The intercharacter
delay needs to be
added to the
Add some intercharacter delay to
the transmitted output by using
the MetroSelect Configuration
Guide (MLPN 00-02407).
Characters are
being dropped.
transmitted output.
Keyboard Wedge Only
The unit scans
Make sure the scanner is
configured for the appropriate
mode.
the bar code
but there is no
data.
The unit may not be
configured correctly.
Make sure that the proper PC
type (ie. AT, PS2 or XT) is
selected.
The unit scans
but the data is
not correct.
The unit may not be
configured correctly.
Verify correct country code and
data formatting are selected.
Adjust the intercharacter delay.
Increase the interscan code
delay setting. Adjust whether
the F0 break is transmitted. It
may be necessary to try both
settings.
The unit is not
transmitting
each character.
The unit may not be
configured correctly.
Alpha characters
show as lower
case.
Enable caps lock detect setting
of the scanner to detect whether
the PC is operating in caps lock.
The computer is in
caps lock mode.
Everything
These characters may
not be supported by
the current country’s
key look up table.
works except
for a couple of
characters.
Try operating the scanner
in Alt Mode.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN SPECIFICATIONS
MS3580
Operational
Light Source: Visible Laser Diode (VLD) @ 650 nm
Laser Power: 1.1 mW
Normal Depth of Field: 19 mm - 273 mm (.75"- 10.75")
Reduced Depth of Field: 19 mm - 146 mm (.75"- 5.75")
Omni Scan
0.33 mm (13 mil)
bar code
Scan Speed: 1650 scan lines per second
No. of Scan Lines: 20
Single-Line
Scan Speed: 80 scan lines per second
No. of Scan Lines:
Raster
1
Scan Speed: 320 scan lines per second
No. of Scan Lines:
4
Motor Speed: 5000 RPM
Min Bar Width: 0.127 mm (5.0 mil)
All standard 1-D bar codes including RSS-14,
RSS-Expanded, and RSS-14 Limited
Decode Capability:
RS232, Keyboard Wedge, Stand-Alone Keyboard, Light Pen
System Interfaces: Emulation, IBM468x/469x, USB (low speed and full speed),
Laser Emulation, RS232 TTL, OCIA
Print Contrast: 35% minimum reflectance difference
Up to 80 data characters
No. Characters Read:
Maximum number will vary based on symbology and density.
Beeper Operation: 7 tones or no beep
Blue = laser on, ready to scan
Indicators (LED):
White = good read, decoding
Specifications subject to change without notice.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN SPECIFICATIONS
MS3580
Mechanical
Width: 63 mm (2.48")
Depth: 50 mm (1.97")
Height: 68 mm (2.68")
Weight: 6 oz (170 g)
Electrical
Voltage Supply: 5VDC ± 0.25V
Operating Power: 1.375 W
Standby Power: 1.0 W
Operating Current: 275 mA typical at 5VDC
Standby Current: 230 mA typical at 5VDC
DC Transformers: Class II; 5.2VDC @ 650 mA
IEC 60825-1:1993+A1:1997+A2:2001
EN 60825-1:1994+A11:1996+A2:2001
EMC: FCC, ICES-003 & EN 55022 Class A
Laser Class 1:
Environmental
Operating Temperature: -20°C to 40°C (-4°F to 104°F)
Storage Temperature: -40°C to 60°C (-40°F to 140°F)
Humidity: 5% to 95% relative humidity, non-condensing
Contaminants: Sealed to resist airborne particulate contaminants
Ventilation: None required
Specifications subject to change without notice.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATIONS AND PROTOCOLS
The model number on each scanner includes the scanner number and factory
default communications protocol.
VERSION
IDENTIFIER
SCANNER
COMMUNICATION PROTOCOL(S)
9
OCIA and RS232 Transmit/Receive
IBM 46XX and Full RS232C
11
RS232 Low Speed USB,
Keyboard Emulation or Serial Emulation
38
40
41
Full-Speed USB
MS3580
Full RS232C/Light Pen Emulation
Keyboard Wedge, Stand-Alone Keyboard and
RS232 Transmit/Receive
47
RS232, Transistor - Transistor Logic (TTL),
Laser Emulation
104
The MS3580 scanner with built-in PC Keyboard Wedge Interface is designed to
be used for keyboard emulation only. Many RS232 configurable
functions (e.g. formatting) available in other Metrologic scanners are also
available as keyboard wedge functions.
The following are the most important selectable options specific to the keyboard
wedge.
Keyboard Type
•
•
•
** AT (includes IBM® PS2 models 50, 55, 60, 80)
XT
IBM PS2 (includes models 30, 70, 8556)
Keyboard Country Type
•
•
•
USA **
Belgium
French
•
•
•
German
Italian
Japan
•
•
•
Spanish
Swiss
United Kingdom
** Default setting. For a complete list of default settings, see Default Settings -
Communication Parameters starting on page 34 of this guide. Refer to the
MetroSelect® Configuration Guide (MLPN 00-02407) or MetroSet2’s help files
for information on how to change the default settings.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS - COMMUNICATION PARAMETERS
Many functions of the scanner can be "configured" - that is enabled or disabled.
The scanner is shipped from the factory configured to a set of default conditions.
The default parameter of the scanner has an asterisk ( * ) in the charts on the
following pages. If an asterisk is not in the default column then the default setting
is Off or Disabled. Every interface does not support every parameter. If the
interface supports a parameter listed in the charts on the following pages, a
check mark (ꢀ) will appear.
RS232*
OR
LIGHT IBM
LASER
EMULATION
PARAMETER
DEFAULT OCIA USB
KBW
RS232 PEN 46XX
TTL
UPC/EAN
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
*
*
*
*
Code 128
Code 93
Codabar
Interleaved 2 of 5 (ITF)
MOD 10 Check on ITF
Code 11
Code 39
*
Full ASCII Code 39
MOD 43 Check on Code 39
MSI-Plessey
MSI-Plessey
10/10 Check Digit
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
MSI-Plessey
MOD 10 Check Digit
Paraf Support
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Variable
4
ITF Symbol Lengths
Minimum Symbol Length
Symbol Length Lock
RSS14 Enable
None
RSS14 ID “]e0”
*
*
*
RSS14 App ID “01”
RSS14 Check Digit
RSS Expanded Enable
34
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS - COMMUNICATION PARAMETERS
RS232*
OR
LIGHT IBM
LASER
EMULATION
PARAMETER
DEFAULT OCIA USB
KBW
RS232 PEN 46XX
TTL
Expanded ID “]e0”
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
RSS Limited Enable
RSS Limited ID “]e0”
RSS Limited App ID “01”
RSS Limited Check Digit
Bars High as Code 39
Spaces High as Code 39
Bars High as Scanned
Spaces High as Scanned
DTS/SIEMENS
*
*
*
*
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
DTS/NIXDORF
*
NCR F
NCR S
Poll Light Pen Source
Beeper Tone
ꢀ
Normal
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Before
Transmit
Beep/Transmit Sequence
Communication Timeout
Razzberry Tone on Timeout
Three Beeps on Timeout
No Beeps on Timeout
Enter Power Save Mode
None
*
5 mins.
Same Symbol Rescan
Timeout: 500 msecs
Configurable in 50 msec
steps (MAX 6.35 seconds)
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
Intercharacter Delay
Configurable in 1 msec
steps (MAX 255 msecs)
1 msecs
10 msecs in
KBW
ꢀ ꢀ ꢀ
ꢀ ꢀ
1
Number of Scan Buffers
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
35
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS - COMMUNICATION PARAMETERS
RS232*
OR
LIGHT IBM
LASER
EMULATION
PARAMETER
DEFAULT OCIA USB
KBW
RS232 PEN 46XX
TTL
Transmit UPC-A
Check Digit
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
Transmit UPC-E
Check Digit
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Expand UPC-E
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Convert UPC-A to EAN-13
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ
Transmit Lead Zero on
UPC-E
Convert EAN-8 to EAN-13
Transmit UPC-A
Number System
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
Transmit UPC-A
Manufacturer ID#
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
*
Transmit UPC-A Item ID#
Transmit Codabar
Start/Stop Characters
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ
ꢀ ꢀ
ꢀ ꢀ
CLSI Editing (Enable)
Transmit Mod 43 Check
Digit on Code 39
Transmit Code 39
Stop/Start Characters
ꢀ ꢀ ꢀ
ꢀ ꢀ
Transmit Mod 10/ITF
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ
ꢀ ꢀ
Transmit MSI-Plessey
Check Characters
Space
9600
Parity
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Baud Rate
8 Data Bits
7 Data Bits
Stop Bits
*
2
Transmit Sanyo ID
Characters
ꢀ ꢀ
ꢀ
36
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS - COMMUNICATION PARAMETERS
RS232*
OR
RS232
TTL
LIGHT IBM
PEN 46XX
LASER
EMULATION
PARAMETER
DEFAULT OCIA USB
KBW
Supplements are not
Required
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
*
Two Digit Redundancy
Five Digit Redundancy
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
100 msec to Find
Supplement Configurable
in 100msec steps
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
(MAX 800 msec)
as code
39
as code
39
Coupon Code 128
ꢀ ꢀ ꢀ
ꢀ ꢀ
Configurable Code
Lengths
7 avail.
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
10
avail.
Configurable Prefix
Characters
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
10
avail.
Configurable Suffix
Characters
ꢀ
ꢀ
Prefixes for individual
Code Types
ꢀ ꢀ
Editing
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Inter Scan-Code Delay
Configurable
(100 µsec steps)
800
µsec
ꢀ
ꢀ
Function/Control Key
Support
Configurable in 5.6 µsec
steps
1 msec
ꢀ
ꢀ
Normal Depth of Field
Reduced Depth of Field
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
38
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS - COMMUNICATION PARAMETERS
RS232*
OR
RS232
TTL
LIGHT IBM
PEN 46XX
LASER
EMULATION
PARAMETER
DEFAULT OCIA USB
KBW
Supplements are not
Required
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
*
Two Digit Redundancy
Five Digit Redundancy
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
100 msec to Find
Supplement
Programmable in
100msec steps
(MAX 800 msec)
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
as code
39
as code
39
Coupon Code 128
ꢀ ꢀ ꢀ
ꢀ ꢀ
Programmable Code
Lengths
7 avail.
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
10
avail.
Programmable Prefix
Characters
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
10
avail.
Programmable Suffix
Characters
ꢀ
ꢀ
Prefixes for individual
Code Types
ꢀ ꢀ
Editing
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Inter Scan-Code Delay
Programmable
(100 µsec steps)
800
µsec
ꢀ
ꢀ
Function/Control Key
Support
Minimum Element Width
Programmable in 5.6 µsec
steps
1 msec
ꢀ
ꢀ
Normal Depth of Field
Reduced Depth of Field
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
*
38
Download from Www.Somanuals.com. All Manuals Search And Download.
UPGRADING THE FLASH ROM FIRMWARE
The MetroSet2 program is a functional component of Metrologic’s new line of
Flash- based scanners. This program allows the user of a Metrologic scanner to
quickly upgrade to a new or custom version of firmware. It requires the use of a
personal computer running Windows 95 or greater and the use of a serial port.
The user merely connects the scanner to a serial port on the PC, launches the
MetroSet2 program, and blasts off to new software upgrades.
Each MS3580, regardless of the version number or communication protocol, can
be upgraded. All RS232 (-41); keyboard wedge (-47); light pen (-41); OCIA (-9);
IBM 468X/469X (-11); low speed USB (-38); integrated full speed USB (-40); and
RS232 TTL, Laser Emulation (-104) units can be upgraded. To upgrade all units,
a power supply and a PowerLink cable (MLPN 54-54014) are required.
RS232 units can be upgraded using the standard PowerLink cable
(MLPN 54-54000x-3).
The program guides the user with its simplistic one click approach. The user
must first select the file. Once the file is selected and verified, the scanner is
ready to be upgraded. Press the “Flash Scanner” button to upgrade the scanner.
The unit will go into a “flash mode” – both the blue and white LEDs will be on.
The user can follow the progress of the upgrade by watching the screen for
details. When the upgrade is complete, the scanner will respond with its normal
one beep on power up. If two beeps occur, the scanner did not upgrade
properly. Contact a Metrologic service representative for additional assistance.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER AND CABLE TERMINATIONS
Scanner Pinout Connections
The MS3580 scanner interfaces terminate to a 10-pin modular socket.
The serial # label indicates the interface enabled when the scanner is shipped
from the factory.
Figure 19. Bottom View of MS3580 (Stand Removed)
MS3580-47 Keyboard Wedge
MS3580-41
and Stand-Alone Keyboard
RS232C and Light Pen Emulation
Pin Function
Pin Function
1
2
3
Ground
1
2
3
Ground
RS232 Transmit Output
RS232 Receive Input
PC Data
RS232 Transmit Output
RS232 Receive Input
RTS Output
4
4
5
PC Clock
5
CTS Input
6
7
KB Clock
PC +5V
6
7
DTR Input/LTPN Source
Reserved
8
KB Data
8
LTPN Data
9
+5VDC
9
+5VDC
10
Shield Ground
10
Shield Ground
MS3580-40
MS3580-38
Full Speed USB
RS232 Low Speed USB
Pin Function
Pin Function
1
2
3
4
5
Ground
1
2
3
4
5
Ground
RS232 Transmit Output
RS232 Receive Input
RTS Output
CTS Input
RS232 Transmit Output
RS232 Receive Input
RTS Output
CTS Input
D+
6
USB D+
6
7
V USB
7
V USB
8
USB D-
8
D-
9
+5VDC
9
+5VDC
10
Shield Ground
10
Shield Ground
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER AND CABLE TERMINATIONS
MS3580-11 IBM 468X/469X
MS3580-9 OCIA
Pin Function
Pin Function
1
2
3
4
5
6
7
Ground
1
2
3
4
5
6
7
Ground
RS232 Transmit Output
RS232 Receive Input
RTS Output
CTS Input
DTR Input
RS232 Transmit Output
RS232 Receive Input
RDATA
RDATA Return
Clock In
IBM B-Transmit
Clock Out
Clock in Return/
Clock out Rtrn
+5VDC
8
IBM A+ Receive
8
9
+5VDC
9
10
Shield Ground
10
Shield Ground
MS3580-104 RS232 TTL, Laser Emulation
Pin Function
1
2
3
Ground
RS232 Transmit Output
RS232 Receive Input
RTS Output (TTL RS232) / Flip Sense
4
5
6
7
8
CTS Input (TTL RS232) / Trigger Emulation Output
DTR Input (TTL RS232) / Scan Enable
Receive (TTL RS232) / Good Read
Transmit (TTL RS232) / Scan Data
+5VDC
9
10
Shield Ground
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER AND CABLE TERMINATIONS
Cable Connector Configurations (Host End)
“Standard” PowerLink Cable
MLPN 54-54000x -3 straight
Pin
1
Function
Shield Ground
9
5
2
RS232 Transmit Output
RS232 Receive Input
DTR Input/Light Pen Source
Power/Signal Ground
Light Pen Data
3
4
5
6
6
1
7
CTS Input
9-Pin D-Type Connector
8
9
RTS Output
+5VDC
USB Power/Communication Cable
MLPN 54-54213x-N-3,
54-54214x-N-3 or 54-54235x-N-3
Pin
Function
PC +5V/V_USB
1
2
3
4
D-
D+
Ground
USB Type A
Locking with Power
USB
Non-Locking
Shield Shield
Stand Alone Keyboard PowerLink
Cable MLPN 54-54020x-3
Pin
1
Function
PC Data
2
No Connect
3
Power Ground
+5VDC PC Power to KB
PC Clock
4
6-Pin Male Mini-DIN Connector
5
6
No Connect
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER AND CABLE TERMINATIONS
Cable Connector Configurations (Host End)
Keyboard Wedge PowerLink Cable
54-54002x -3
Pin
1
Function
Keyboard Clock
2
Keyboard Data
No Connect
3
4
Power Ground
+5 Volts DC
5-Pin DIN, Female
5
Pin Function
1
2
3
PC Data
No Connect
Power Ground
4
5
6
+5 Volts DC
PC Clock
No Connect
6-Pin DIN, Male
Metrologic will supply an adapter cable with a 5-pin DIN male connector on one
end and a 6-pin mini DIN female connector on the other. According to the
termination required, connect the appropriate end of the adapter cable to the
PowerLink cable, leaving the necessary termination exposed for connecting to
the keyboard and the keyboard port on the PC.
Keyboard Wedge Adapter Cable
Pin Function
1
2
3
4
5
PC Clock
PC Data
No Connect
Power Ground
+5 Volts DC
5-Pin DIN, Male
Pin Function
1
2
3
4
5
6
Keyboard Data
No Connect
Power Ground
+5 Volts DC
Keyboard Clock
No Connect
6-pin Mini DIN, Female
43
Download from Www.Somanuals.com. All Manuals Search And Download.
LASER AND PRODUCT SAFETY
Caution
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous laser light exposure. Under no circumstances should the
customer attempt to service the laser scanner. Never attempt to look at the laser beam,
even if the scanner appears to be nonfunctional. Never open the scanner in an attempt to
look into the device. Doing so could result in hazardous laser light exposure. The use of
optical instruments with the laser equipment will increase eye hazard.
Atención
La modificación de los procedimientos, o la utilización de controles o ajustes distintos de
los especificados aquí, pueden provocar una luz de láser peligrosa. Bajo ninguna
circunstancia el usuario deberá realizar el mantenimiento del láser del escáner. Ni intentar
mirar al haz del láser incluso cuando este no esté operativo. Tampoco deberá abrir el
escáner para examinar el aparato. El hacerlo puede conllevar una exposición peligrosa a
la luz de láser. El uso de instrumentos ópticos con el equipo láser puede incrementar el
riesgo para la vista.
Attention
L'emploi de commandes, réglages ou procédés autres que ceux décrits ici peut entraîner
de graves irradiations. Le client ne doit en aucun cas essayer d'entretenir lui-même le
scanner ou le laser. Ne regardez jamais directement le rayon laser, même si vous croyez
que le scanner est inactif. N'ouvrez jamais le scanner pour regarder dans l'appareil. Ce
faisant, vous vous exposez à une rayonnement laser qú êst hazardous. L'emploi
d'appareils optiques avec cet équipement laser augmente le risque d'endommagement de
la vision.
Achtung
Die Verwendung anderer als der hier beschriebenen Steuerungen, Einstellungen oder
Verfahren kann eine gefährliche Laserstrahlung hervorrufen. Der Kunde sollte unter keinen
Umständen versuchen, den Laser-Scanner selbst zu warten. Sehen Sie niemals in den
Laserstrahl, selbst wenn Sie glauben, daß der Scanner nicht aktiv ist. Öffnen Sie niemals
den Scanner, um in das Gerät hineinzusehen. Wenn Sie dies tun, können Sie sich einer
gefährlichen Laserstrahlung aussetzen. Der Einsatz optischer Geräte mit dieser
Laserausrüstung erhöht das Risiko einer Sehschädigung.
Attenzione
L’utilizzo di sistemi di controllo, di regolazioni o di procedimenti diversi da quelli descritti nel
presente Manuale può provocare delle esposizioni a raggi laser rischiose. Il cliente non
deve assolutamente tentare di riparare egli stesso lo scanner laser. Non guardate mai il
raggio laser, anche se credete che lo scanner non sia attivo. Non aprite mai lo scanner per
guardare dentro l’apparecchio. Facendolo potete esporVi ad una esposizione laser
rischiosa. L’uso di apparecchi ottici, equipaggiati con raggi laser, aumenta il rischio di
danni alla vista.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
LASER AND PRODUCT SAFETY
Notices
This equipment has been tested and found to comply with limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the
interference at their own expense. Any unauthorized changes or modifications to this
equipment could void the user’s authority to operate this device.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Notice
This Class A digital apparatus complies with Canadian ICES-003.
Remarque
Cet appareil numérique de la classe A, conformé a la norme NMB-003 du Canada.
European Standard
Warning
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Funkstöreigenschaften nach EN 55022:1998
Warnung!
Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich
Funkstörungen verursachen; in diesem fall kann vom Betrieber verlangt werden,
angemessene Maßnahmen durchführen.
Standard Europeo
Attenzione
Questo e’ un prodotto di classe A. Se usato in vicinanza di residenze private potrebbe
causare interferenze radio che potrebbero richiedere all’utilizzatore opportune misure.
Attention
Ce produit est de classe “A”. Dans un environnement domestique, ce produit peut être
la cause d’interférences radio. Dans ce cas l’utiliseteur peut être amené à predre les
mesures adéquates.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
The MS3580 QuantumT™ scanners are manufactured by Metrologic at its Blackwood, New Jersey,
U.S.A. facility. The MS3580 QuantumT scanners have a three (3) year limited warranty from the date of
manufacture. Metrologic warrants and represents that all MS3580 QuantumT scanners are free of all
defects in material, workmanship and design, and have been produced and labeled in compliance with
all applicable U.S. Federal, state and local laws, regulations and ordinances pertaining to their
production and labeling.
This warranty is limited to repair, replacement of product or refund of product price at the sole discretion
of Metrologic. Faulty equipment must be returned to one of the following Metrologic repair facilities:
Blackwood, New Jersey, USA; Madrid, Spain; or Suzhou, China. To do this, contact the appropriate
Metrologic Customer Service/Repair Department to obtain a Returned Material Authorization (RMA)
number.
In the event that it is determined the equipment failure is covered under this warranty, Metrologic
shall, at its sole option, repair the Product or replace the Product with a functionally equivalent unit
and return such repaired or replaced Product without charge for service or return freight, whether
distributor, dealer/reseller, or retail consumer, or refund an amount equal to the original purchase
price.
This limited warranty does not extend to any Product which, in the sole judgment of Metrologic,
has been subjected to abuse, misuse, neglect, improper installation, or accident, nor any damage
due to use or misuse produced from integration of the Product into any mechanical, electrical or
computer system. The warranty is void if the case of Product is opened by anyone other than
Metrologic’s repair department or authorized repair centers.
THIS LIMITED WARRANTY, EXCEPT AS TO TITLE, IS IN LIEU OF ALL OTHER WARRANTIES
OR GUARANTEES, EITHER EXPRESS OR IMPLIED, AND SPECIFICALLY EXCLUDES,
WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE UNDER THE UNIFORM COMMERCIAL CODE, OR ARISING OUT OF
CUSTOM OR CONDUCT. THE RIGHTS AND REMEDIES PROVIDED HEREIN ARE
EXCLUSIVE AND IN LIEU OF ANY OTHER RIGHTS OR REMEDIES. IN NO EVENT SHALL
METROLOGIC BE LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES TO PERSON OR PROPERTY, OR EFFECT ON
BUSINESS OR PROPERTY, OR OTHER DAMAGES OR EXPENSES DUE DIRECTLY OR
INDIRECTLY TO THE PRODUCT, EXCEPT AS STATED IN THIS WARRANTY. IN NO EVENT
SHALL ANY LIABILITY OF METROLOGIC EXCEED THE ACTUAL AMOUNT PAID TO
METROLOGIC FOR THE PRODUCT. METROLOGIC RESERVES THE RIGHT TO MAKE ANY
CHANGES TO THE PRODUCT DESCRIBED HEREIN.
CORPORATE HEADQUARTERS,
NORTH AMERICA
METROLOGIC EUROPEAN REPAIR CENTER
(MERC)
Metrologic Instruments, Inc.
90 Coles Rd.
Blackwood, NJ 08012-4683
Customer Service Department
Tel: 1-800-ID-METRO
Fax: 856-228-6673
Metrologic Eria Ibérica, SL
C/Alfonso Gomez, 38-40, 1D
28037 Madrid
Tel: +34 913 751 249
Fax: +34 913 270 437
Email: [email protected]
MTLG AUTO ID INSTRUMENTS (SHANGHAI) CO., LTD
Suzhou Sales Office
BLK A, Room# 03/03-04
No.5 Xinghan Street, Xinsu Industrial Square
China-Singapore Suahou Industrial Park, Suzhou, PRC
Tel: 86-512-67622550
Fax: 86-512-67622560
Email: [email protected]
46
Download from Www.Somanuals.com. All Manuals Search And Download.
PATENTS
Patent Information
This METROLOGIC product may be covered by one or more of the following
U.S. Patents:
U.S. Patent No.;
5,216,232; 5,260,553; 5,340,971; 5,424,525; 5,484,992; 5,525,789;
5,528,024; 5,557,093; 5,616,908; 5,627,359; 5,637,852; 5,661,292;
5,777,315; 5,789,730; 5,789,731; 5,811,780; 5,828,048; 5,844,227;
5,925,870; 6,029,894; 6,098,885; 6,209,789; 6,257,492; 6,286,760;
6,299,067; 6,347,743; 6,412,696; 6,460,767; 6,604,684; 6,857,572;
6,860,427
No license right or sublicense is granted, either expressly or by implication,
estoppel, or otherwise, under any METROLOGIC or third party intellectual
property rights (whether or not such third party rights are licensed to
METROLOGIC), including any third party patent listed above, except for an
implied license only for the normal intended use of the specific equipment,
circuits, and devices represented by or contained in the METROLOGIC products
that are physically transferred to the user, and only to the extent of
METROLOGIC’S license rights and subject to any conditions, covenants and
restrictions therein.
Other worldwide patents pending.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
Firmware..................................... 39
Flash ROM.............................. 1, 39
AC .......................................2, 8–12
Accessories...............................2, 3
Adapter........................................10
Audible Indicator.............13, 19–21,
27–30, 39
H
Host ...................................... 27–30
I
B
IBM ................................... 9, 34–38
Indicator
Audible ....... 4, 13, 19–21, 27–30,
31, 39
Bar Code .............19–21, 27–30, 31
Bar Width.....................................31
Beep..............19, 20, 21, 27–30, 39
Blue LED .............19–21, 27–30, 39
Button................................4, 13–18
Failure ..................................... 21
Visual .... 4, 19–21, 27–30, 31, 39
Interface...................................... 31
IBM............................ 1, 9, 34–38
Keyboard Wedge1, 10, 30, 34–38
Laser Emulation ........ 1, 8, 34–38
Light Pen ................... 1, 8, 34–38
OCIA ......................... 1, 9, 34–38
RS232 ........... 1, 8, 29, 30, 34–38
RS232 TTL...................... 1, 8, 33
Stand-Alone Keyboard ........ 1, 11
Troubleshooting................. 27–30
USB......................... 1, 12, 34–38
IR ................................................ 26
C
Cable
Communication...2, 8–12, 27–30,
39, 42–43
Keyboard Wedge...............42–43
Pin Assignments................42–43
PowerLink..2, 5, 8–12, 39, 42–43
Troubleshooting.................27–30
USB ...................................42–43
Caution..........................5, 8–12, 44
Class ...........................................45
CodeGate..........................1, 13–18
Communication .........20, 27–30, 33
Parameters ........................34–38
Compliance .............................8–12
Components..............................2, 4
Configuration.........................19, 21
Default ...............................34–38
Current ........................................32
Customer Service..................46, 50
K
Keyboard Country Type.............. 33
Keyboard Type............................ 33
Keyboard Wedge ...... 10, 30, 34–38
L
Label
Caution...................................... 5
Serial Number ........................... 5
Laser........................................... 44
Laser Aperture .............................. 4
Laser Emulation................ 8, 34–38
LED....................................... 19–21
Light Pen........................... 8, 34–38
Light Source................................ 31
D
DC...........................................2, 32
Default Settings...13, 14, 33, 34–38
Depth of Field
Normal ...................22, 24, 31, 38
Reduced ..........23, 24, 25, 31, 38
F
M
Failure
Maintenance ................................. 5
Manual .............................. 2, 19, 33
MetroSet2 ................................... 39
Modes......................................21
FCC.............................................45
48
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
S
Mode of Operation
Button ......................................18
Primary ..............................13–18
Secondary..........................13–18
Sweet Spot Mode ....................38
Motor Speed................................31
Mounting Specifications ................5
Scan Lines .................................. 31
Scan Pattern ........................... 1, 31
Horizontal Raster..................... 13
Omnidirectional ................. 13–18
Primary.............................. 13–18
Secondary ......................... 13–18
Single-Line ........................ 13–18
Scan Speed ................................ 31
SELV....................................... 8–12
Single-Line............................ 13–18
Specification
N
Notices ........................................45
O
Electrical.................................. 32
Environmental ......................... 32
Mechanical .............................. 32
Operational.............................. 31
Stand-Alone Keyboard................ 11
Storage ....................................... 32
Sweet Spot Mode........................ 38
OCIA .................................9, 34–38
Omnidirectional .....................13–18
Operation.....................................45
P
Patents ........................................47
PC .........................................33, 43
Pin Assignments
T
Cable .................................42–43
Scanner .............................40–41
Port..............................8–12, 27–30
Power ............................2, 8–12, 39
PowerLink................................8–12
Product Safety.............................44
Property.......................................47
Protocol .......................................33
Tone............................................ 19
Tones............................................ 1
Transformer ............................ 2, 32
Troubleshooting .................... 27–30
U
Upgrade ...................................... 39
USB ................................ 12, 34–38
R
V
RAM ............................................29
Raster....................................13–18
Razzberry Tone...............19–21, 29
Repair..........................................21
Replacement Parts........................3
RMA ............................................46
ROM............................................29
RS232 ...................8, 29, 30, 34–38
RS232 TTL..............................8, 33
Ventilation ................................... 32
Visual Indicator ... 19–21, 27–30, 39
Blue LED ........... 4, 19–21, 27–30
White LED ......... 4, 19–21, 27–30
Yellow LED........ 4, 19–21, 27–30
Voltage.............................. 8–12, 32
Volume........................................ 19
W
Warranty ..................................... 46
Weight......................................... 31
White LED........... 19–21, 27–30, 39
Window......................................... 4
49
Download from Www.Somanuals.com. All Manuals Search And Download.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
May 2006
Printed in the USA
0 0 - 0 5 0 9 0 C
Download from Www.Somanuals.com. All Manuals Search And Download.
|