Metrologic Instruments Scanner MLPN 2407 User Manual

MetroSelect^™Configuration Guide

MLPN 2407/February 2000

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Table of Contents

Introduction

iii

Section A: Code Types & Decode Rules

Section B: Supplements

Section C: Communications

Section D: Scanner Operation

Section E: Prefixes/Suffixes

Section F: Code Formatting

Section G: RS-232

Section H: Keyboard

Section I: OCIA

Section J: Light Pen Parameters

Section K: IBM 46xx

Section L: MS9500 Voyager™

Section M:Code Bytes

Section N: Miscellaneous Features

Download from Www.Somanuals.com. All Manuals Search And Download.

iii

MetroSelect^™

Introduction

Your new scanner has been configured at the factory with default settings.

Many host systems have unique formats and protocol requirements. Therefore, Metrologic

provides a wide range of configurable features that may be selected using this bar code based

configuration tool. Once the configuration is completed, the scanner stores the settings in

nonvolatile memory (NOVRAM). NOVRAM saves the settings when the power is turned off.

Note: Every bar code with an “ * ” (asterisk) is a default setting.

Bar codes with a “~” (tilde) require multi-code configuration method.

Directions

The MetroSelect class of scanners can be bar code configured in two ways: Single Code

Method and Multi-Code Method.

Single Code Method: Most features can be enabled or disabled using the single code

method. Scan the bar code next to the feature. The scanner will give a “good scan” beep. A

multi-tone beep will follow to indicate the configuration has been saved to NOVRAM.

Multi-Code Method: All features can be enabled or disabled using the multi-code

method. A feature with a “~” requires the multi-code method. To use the multi-code

method, scan the “Enter/Exit Configuration Mode” code. Next, scan the codes for the

needed feature. Then scan the Enter/Exit Configuration Code to exit and save the configura-

tion changes. To abort a configuration change, power off the scanner before scanning the

Enter/Exit code.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Bar Code Configuration Methods

Single Code Method

1. Power up scanner

2. Scan the bar code for the desired feature

3. Observe a “good scan” beep, quickly followed by a multi-toned,

“save setting” beep.

Multi-Code Method

1. Power up scanner

2. Scan Enter/Exit Configuration Mode bar code

(3 beeps)

3. Scan bar code for the desired feature

(1 beep)

4. Scan Enter/Exit Configuration Mode bar code

(3 beeps) and save new configuration.

999999

Enter/ Exit

Configuration Mode

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Need to start over?

Use the Recall Default bar code. This will erase all previous settings and return to the scanner’s default

communications protocol.

-Keyboard Wedge interface scanners will load keyboard wedge defaults.

-All other scanners load RS-232 defaults.

Note: Metrologic manufactures custom OEM scanners which load the OEM’s defaults. Section N will

explain how this affects “Metrologic Defaults.”

Recall Defaults

999998

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section A

Code Types and Decode Rules

UPC-EAN

A-1

Code 128

A-3

Code 39

A-4

Interleaved 2 of 5

Standard 2 of 5

Other 2 of 5 Codes

Codabar

A-6

A-8

A-9

A-10

A-11

A-12

A-13

A-15

A-16

Code 93

Code 11

Telepen

Plessey Codes

Other Decode Features

Configurable Code Lengths

Download from Www.Somanuals.com. All Manuals Search And Download.

A-1

MetroSelect^™

UPC/ EAN

*Enable UPC/EAN

Disable UPC/EAN

100116

100106

*Enable UPC-A

Disable UPC-A

100216

100206

*Enable UPC-E

Disable UPC-E

100210

100200

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

*Enable EAN-13

Disable EAN-13

Disable EAN-8

100211

100201

*Enable EAN-8

100214

100204

A-2

Download from Www.Somanuals.com. All Manuals Search And Download.

A-3

MetroSelect^™

Code 128

*Enable Code 128

Disable Code 128

100113

100103

Enable UCC/EAN - 128

‘]C1’ Code formatting

*Disable UCC/EAN -128

‘]C1’ Code formatting

100314

100304

For Coupon Code 128,

see Section B.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Code 39

Disable Code 39

*Enable Code 39

100111

100101

Enable MOD 43

Check on Code 39

*Disable MOD 43 Check on

Code 39

100213

100203

When enabled, the scanner will only

scan Code 39 bar codes that have a

valid Modulo 43 check digit.

The scanner will not test Code 39

bar codes for a Modulo 43 check

digit.

Enable Full ASCII Code 39

100217

*Disable Full ASCII Code 39

100207

A-4

Download from Www.Somanuals.com. All Manuals Search And Download.

A-5

MetroSelect^™

Enable PARAF (Italian

Pharmaceutical Codes)

Support

*Disable PARAF Support

100205

100215

When enabled, the scanner will

convert Code 39 bar codes to

PARAF format.

When disabled, the scanner will not

convert Code 39 bar codes to PARAF

format.

Enable TRI-OPTIC Code

*Disable TRI-OPTIC Code

100302

100312

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Interleaved 2 of 5

*Enable Interleaved

2 of 5 (ITF)

Disable Interleaved

2 of 5 (ITF)

100105

100115

Enable MOD 10

Check on ITF

*Disable MOD 10

Check on ITF

100300

100310

When option disabled, the scanner will

not test Interleaved 2 of 5 (ITF) bar

codes for a Modulo 10 check digit.

When option enabled, the scanner will

only scan Interleaved 2 of 5 (ITF) bar

codes that have a Modulo 10 check

digit.

A-6

Download from Www.Somanuals.com. All Manuals Search And Download.

A-7

MetroSelect^™

~ITF Symbol Length Lock 1

~ITF Symbol Length Lock 2

901700

901600

To specify a First ITF symbol length

lock, scan the above bar code and the

appropriate code bytes located in

Section M. RefertoMultiCodeMethod

onpageiii.

To specify a second ITF symbol length

lock, scan the above bar code and the

appropriate code bytes located in

Section M. RefertoMultiCodeMethod

onpageiii.

~ITF Minimum Symbol

Length

903400

TospecifyaminimumnumberofITF

characterstobedecoded, scantheabove

barcodeandtheappropriatecode bytes

locatedinSection M. RefertoMultiCode

Methodonpageiii.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Standard 2 of 5

Enable Standard

2 of 5

*Disable Standard

2 of 5

100110

100100

~Standard 2 of 5 Symbol Length

901500

TospecifyaminimumnumberofITF

characterstobedecoded, scantheabove

barcodeandtheappropriatecodebytes

locatedinSection M. RefertoMultiCode

Methodonpageiii.

A-8

Download from Www.Somanuals.com. All Manuals Search And Download.

A-9

MetroSelect^™

Other 2 of 5 Codes

Enable Matrix 2 of 5

100015

*Disable Matrix 2 of 5

100005

Enable 15 Digit

Airline 2 of 5

*Disable 15 Digit

Airline 2 of 5

100004

100014

*Disable 13 Digit

Airline 2 of 5

Enable 13 Digit

Airline 2 of 5

100303

100313

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable Hong Kong

2 of 5

*Disable Hong Kong

2 of 5

100306

100316

Codabar

*Enable Codabar

Disable Codabar

100104

100114

Enable Dual Field Codabar

*Disable Dual Field Codabar

100002

100012

A-10

Download from Www.Somanuals.com. All Manuals Search And Download.

A-11

MetroSelect^™

Code 93

*Enable Code 93

Disable Code 93

100102

100112

Code 11

Enable Code 11

*Disable Code 11

100003

100013

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Telepen

Enable Telepen

*Disable Telepen

100007

100017

Enable ALPHA Telepen

*Disable ALPHA Telepen

100006

100016

_DownloA_ad-1_fr2_{om Www.Somanuals.com. All Manuals Search And Download.}

A-13

MetroSelect^™

Plessey Codes

Enable MSI Plessey

*Disable MSI Plessey

100202

100212

*No MSI Plessey

Check Digit

200704

This option will not test MSI Plessey bar

codes for a check digit.

Enable MSI Plessey MOD 10/10

Check Digit

*Enable MSI Plessey

Mod 10 Check digit

200724

200734

Test MSI Plessey bar codes for a single

Modulo 10 check digit.

Test MSI Plessey bar codes for a double

Modulo 10 check digit.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable UK Plessey

*Disable UK Plessey

100107

100117

*UK Plessey A

to X Conversion Disabled

UK Plessey A

to X Conversion Enabled

100706

100716

Disables UK Plessey A to X

Conversion.

Enables UK Plessey A to X

Conversion.

_DownloA_ad-1_fr4_{om Www.Somanuals.com. All Manuals Search And Download.}

A-15

MetroSelect^™

Other Decode Features

Enable Double Border

Required/Large Intercharacter

Space

*Disable Double Border

Required/Large Intercharacter

Space

100001

100011

~Minimum Symbol Length

901800

~Symbol Length Lock

901900

Omnidirectional default is 4. Single-line

default is 3. Combine this code with the

proper Code Bytes, to specify the

minimum number of characters in all

non-UPC/EAN bar codes.

This code combined with the proper

Code Bytes, locks the bar codes’ length

into place. Refer to Multi-Code

Method on page iii.

Refer to Multi-Code Method on page iii.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Configurable Code Lengths

There are seven bar code lock lengths available. Specific code types can be assigned to a lock length.

While in programming mode, start with lock length 1, then scan three Code Byte bar codes from

Section M that represent the bar code length. (A table with the code type values can be found in

Section M) Refer to Multi-Code Method on page iii.

This process can be repeated for lock lengths 2 through 7.

~Code Lock #1:

Code Type

~Code Lock #1:

Length

902100

902000

~Code Lock #2: Code Type

~Code Lock #2: Length

902200

902300

_DownloA_ad-1_fr6_{om Www.Somanuals.com. All Manuals Search And Download.}

A-17

MetroSelect^™

~Code Lock #3:

Length

~Code Lock #3:

Code Type

902400

902500

~Code Lock #4:

Length

~Code Lock #4:

Code Type

902600

902700

~Code Lock #5:

Length

~Code Lock #5:

Code Type

902800

902900

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

~Code Lock #6:

Code Type

Length

903000

903100

~Code Lock #7:

Length

~Code Lock #7:

Code Type

903200

903300

A-18

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section B

Supplements

Two Digit Supplements

B-1

B-2

B-3

B-4

B-5

B-6

B-7

B-8

Two Digit Redundancy

Five Digit Supplements

Five Digit Redundancy

Supplements Required/Not Required

Remote Supplemental Requirement

Bookland (978) Supplement Requirement

977 (2 digit) Supplement Requirement

378/379 French Supplement Requirement

434/439 German Supplement Requirement

#System 2 Requires Supplements

#System 5 Requires Supplements

Coupon Code 128

Code 128 ‘]C1’ Extended Code Format

Code 128 Group Separators

400 msec to find Supplemental

200 msec to find Supplemental

100 msec to find Supplemental

Code ID’s with Supplements

Beep Once/Twice on Supplements

ISBN Check Digit Transmission

Bookland to ISBN Conversion

ISBN Re-formatting

Download from Www.Somanuals.com. All Manuals Search And Download.

B-1

MetroSelect^™

Supplements

Enable Two Digit Supplements

101217

*Disable Two Digit Supplements

101207

*Enable Two Digit Redundancy

101212

Disable Two Digit Redundancy

101202

Twice before accepting data, the

scanner will scan the bar code plus

the 2 digit add on.

When Scanned, will not implement

the two digit redundancy feature.

*Disable Five Digit Supplements

101206

Enable Five Digit Supplements

101216

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

*Disable Five Digit

Redundancy

Enable Five Digit

Redundancy

101211

101201

When Scanned, will not implement

the five digit redundancy feature.

Twice before accepting data, the

scanner will scan the bar code plus

the five digit add on.

Supplements are Required

101213

*Supplements are not Required

101203

When chosen, all UPC/EAN labels

that are scanned must have a sup-

plement.

When chosen, all UPC/EAN labels do

not require a supplement to be

scanned.

*Disable Remote Supplemental

Requirement

Enable Remote Supplemental

Requirement

101416

101406

B-2

Download from Www.Somanuals.com. All Manuals Search And Download.

B-3

MetroSelect^™

Enable Bookland

*Disable Bookland

(978) Supplement Requirement

101417

101407

*Disable 977 (2 digit)

Enable 977 (2 digit)

Supplemental Requirement

101314

101304

When enabled, the scanner will

require a 2 digit supplement be

scanned whenever an EAN-13 code

begins with 977.

When enabled, the scanner will not

require a 2 digit supplement be

scanned whenever an EAN-13 code

begins with 977.

*Disable 378/379 French

Supplemental Requirement

Enable 378/379 French

Supplemental Requirement

101313

101303

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable 434/439 German

Supplemental Requirement

*Disable 434/439 German

Supplemental Requirement

101415

101405

Enable #System 2 Requires

Supplements

*Disable #System 2 Requires

Supplements

101412

101402

Enable #System 5 Requires

Supplements

*Disable #System 5 Requires

Supplements

101215

101205

B-4

Download from Www.Somanuals.com. All Manuals Search And Download.

B-5

MetroSelect^™

Enable Coupon Code 128

100315

*Disable Coupon Code 128

100305

Enable Code 128 ‘]C1’ Extended

Code Format

*Disable Code 128 ‘]C1’

Extended Code Format

101411

101401

When enabled, scanner transmits an

‘]C1’ at the beginning of the Code

128 portion of the coupon code.

When disabled, scanner will not trans-

mit on ‘]C1’ at the beginning of the

Code 128 portion of the coupon code.

Enable 128 Group Separators

101414

*Disable 128 Group Separators

101404

“GS” (1DH) character will notbe

transmittedwithcoupon Code128codes.

“GS” (1DH) character will be transmit-

ted with coupon Code 128 codes.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

200 msec to Find Supplemental

301320

400 msec to Find Supplemental

301340

With this option, the scanner will allot

200 milliseconds to “find” an add on

after a main UPC/EAN bar code has

been scanned.

With this option, the scanner will allot

400 milliseconds to “find” an add on

after a main UPC/EAN bar code has

been scanned.

*100 msec to Find Supplemental

301310

With this option, the scanner will allot

100 milliseconds to “find” an add on

after a main UPC/EAN bar code has

been scanned.

B-6

Download from Www.Somanuals.com. All Manuals Search And Download.

B-7

MetroSelect^™

Enable Code ID’s with

Supplements

*Disable Code ID’s with

Supplements

101214

101204

*Beep Once on Supplements

118406

Beep Twice on Supplements

118416

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable ISBN Check Digit

Transmission

Disable ISBN Check Digit

Transmission

101315

101305

Not available with all models.

*Disable Bookland to ISBN

Conversion

Enable Bookland to ISBN

Conversion

101317

101307

Not available with all models.

*Disable ISBN

Re-Formatting

Enable ISBN

Re-Formatting

101316

101306

Not available with all models.

B-8

Download from Www.Somanuals.com. All Manuals Search And Download.

B-9

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section C

Communications

Enable Light Pen/Wand Communication

C-1

C-2

C-3

Enable RS-232

Load Keyboard Wedge Defaults

Enable Stand-Alone Keyboard Scanner

Enable Keyboard Wedge Emulation

Enable OCIAOutput

Load OCIA Defaults

Enable IBM 46xx Communication

Load IBM 46xx IBM Defaults

Enable No Communication Mode

Reserved

_{Download from Www.Somanua}C_{ls.com. All Manuals Search And Download.}

C-1

MetroSelect^™

Communications

Enable Light Pen/Wand

Communication

*Enable RS-232

415554

415524

When this option is enabled, the scanner

willworkwithRS-232+/-12Vserial

output.

Use this option if scanner should be

used in place of a light pen.

Load Keyboard Wedge Defaults

999994

Scan this before selecting Normal or

Stand Alone Mode.

Enable Keyboard Wedge Emulation

5155143

Enable Stand-Alone Keyboard

Scanner

5155153

Select if the scanner provides keyboard emu-

lationbyconvertingthescannedbarcodedata

tothePCkeyboardscancodeequivalent.

Allows scanner to be used without an

external keyboard.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable OCIA Output

Load OCIA Defaults

415544

999993

Selectthisoptionifthecommunications

requirementisan Optically Coupled

Interface Adapter(OCIA).Thisaclocked

(bythehost)serialinterface.

Scan this before selecting Enable

OCIA output

Enable IBM 46xx Communication

415504

Load IBM 46xx Defaults

999995

Select this option for IBM 46XX

SIOC/RS485 communications. Not all

scanners support this interface. The

correct interface board is required.

Scan this before selecting

IBM 46XX Defaults

C-2

Download from Www.Somanuals.com. All Manuals Search And Download.

C-3

MetroSelect^™

Enable No Communication Mode

415534

Select this option if the scanner does

not interface with the host device.

Reserved

415564

Reserved

917500

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section D

Scanner Operation

Configuration Mode Options

Scan Buffers

D-1

D-2

Redundant Scans

D-4

Miscellaneous Decode Features

Depth of Field Adjustments

Same Symbol Time Outs

LED Options

D-6

D-7

D-8

D-10

D-11

D-14

D-15

D-16

D-18

D-22

D-24

D-25

Beeper Options

Data Transmission Delays

Inter-Character

Inter-Record

Communication Timeout Options

Host Scanner Commands

Power Save Modes

Miscellaneous Features

Test Modes

_{Download from Www.Somanuals.com. All}D_{Manuals Search And Download.}

D-1

MetroSelect^™

Configuration Mode

Allow Configuration Mode on

Power-Up

*Allow Configuration Mode

Anytime

118117

118107

Scanner can only enter MetroSet™

mode before any bar codes are

scanned.

Allow MetroSet™configurationatany

time.

Allow Configuration Labels on

Power-up

*Allow Configuration Labels

Anytime

118116

118106

Allows scanningofconfigurationbar

codesany time.

Once a product bar code is scanned

after power-up, the scanner will not

accept configuation bar codes.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Scan Buffers

2 Scan Buffers

*1 Scan Buffer

318000

318010

When enabled, the scanner will scan

2 bar codes in the scan field one time

each. These 2 bar codes will not be

scanned again until they are removed

from the scan field for the duration of

the same symbol time out.

When enabled, the scanner will scan

one bar code in the scan field and not

scan again until the bar code is

removed from the scan field for the

duration of the same symbol time

out.

3 Scan Buffers

318020

318030

Same function as 2 Scan Buffers, but

4 bar codes are in the scan field.

Same function as 2 Scan Buffers, but

3 bar codes are in the scan field.

5 Scan Buffers

318040

6 Scan Buffers

318050

Same function as 2 Scan Buffers,

but 6 bar codes are in the scan field.

Same function as 2 Scan Buffers, but

5 bar codes are in the scan field.

_{Download from Www.Somanuals.com. A}D_ll-_M2_{anuals Search And Download.}

D-3

MetroSelect^™

7 Scan Buffers

8 Scan Buffers

318060

318070

Same function as 2 Scan Buffers, but

7 bar codes are in the scan field.

Same function as 2 Scan Buffers, but

8 bar codes are in the scan field.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Redundant Scans

*0 Redundant Scans

301100

1 Redundant Scans

301110

Requires 1 good decode for a “good

scan.”

Requires 2 consecutive decodes of the

same bar code data for a “good

scan” .

2 Redundant Scans

301120

3 Redundant Scans

301130

Requires 3 consecutive...

Requires 4...

4 Redundant Scans

301140

5 Redundant Scans

301150

Requires 5...

Requires 6...

D-4

Download from Www.Somanuals.com. All Manuals Search And Download.

D-5

MetroSelect^™

7 Redundant Scans

6 Redundant Scans

301160

301170

Requires 7...

Requires 8...

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Miscellaneous Decode Features

*Enable MAJIC

101113

Disable MAJIC

101103

Disable this feature when bar codes

are in good reading condition. This

will speed up decoding and improve

over all accuracy.

The Metrologic Algorithm for Joining

Incomplete Codes (MAJIC) aids in

deciphering damaged or incomplete

bar codes. Enable for more aggres-

sive decoding.

Optional Same Symbol Check

118113

*Normal Same Symbol Check

118103

Require 1 different character between

successive bar codes to consider the bar

code “new”.

Require 3 different characters between

successive bar codes to consider the bar

code “new”.

D-6

Download from Www.Somanuals.com. All Manuals Search And Download.

D-7

MetroSelect^™

Depth of Field Adjustments

Do not change these settings unless instructed by a Metrologic representative.

*Optimize for Low Density Codes

418790

Optimize for High Density Codes

4187130

For use with omnidirectional

scanners only.

For use with omnidirectional

scanners only.

Fixed for High Density Codes

418700

Fixed for Medium Density

418710

For use with omnidirectional

scanners only.

For use with omnidirectional

scanners only.

Fixed for Low Density Codes

418720

For use with omnidirectional

scanners only.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Same Symbol Time outs

These numbers determine the length of time before a bar code can be rescanned afterit is removed from the scan field. Single

codefixedsettingsinmsecsofNo,50, 100,200,500,1200(1.2sec),2000(2.0sec)andinfiniteareavailable. Also,user-config-

urablevaluecan besetin user-configurableincrementsof50forarangeof50msecsto6350(6.35sec).

If using the MS9500 series, please go to Section L.

No Same Symbol Time Out

Same Symbol Time Out 100

msecs

818900

818920

*Same Symbol Time Out 500 msecs

8189100

Same Symbol Time Out 200

msecs

818940

Same Symbol Time Out 1200 msecs

8189240

Same Symbol Time Out 2000 msecs

8189400

_{Download from Www.Somanuals.com. A}D_ll-_M8_{anuals Search And Download.}

D-9

MetroSelect^™

Infinite Same Symbol Time Out

118917

~Variable Same Symbol Time-

out

918900

When selected, the scanner will not

repetitively scan the same bar code.

This option overrides the symbol res-

can time-outs.

In configuration mode, scan this bar

code and a code byte sequence from

Section M to set the same symbol

time out duration. Values range

from 001 to 127 (50 to 6350

msecs). Refer to MultiCode Method

on page iii.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

LED Options

Flash Green LED if Rescan

Allowed

*Do Not Flash Green LED if

Rescan Allowed

118313

118303

This indicates same symbol timeout

has elapsed.

Reverse LED

Functions

*Normal LED

Functions

118312

118302

Red = Laser On

Green = Good Read

Green = Laser On

Red = Good Read

D-10

Download from Www.Somanuals.com. All Manuals Search And Download.

D-11

MetroSelect^™

Beeper Options

*Normal Tone

318575

Optional Tone 1

318565

Optional Tone 2

318555

Optional Tone 3

318545

Optional Tone 4

318535

Optional Tone 5

318525

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Optional Tone 6

No Beep

318515

318505

Beep Twice on Supplements

*Beep Once on Supplements

118406

118416

Enable Fast Beep

*Disable Fast Beep

118414

118404

_{Download from Www.Somanuals.com.}D_A-_ll1_M2_{anuals Search And Download.}

D-13

MetroSelect^™

*Ignore BEL

Command

Beep on BEL Command

118417

118407

The scanner beeps when it receives

a BEL character from the host. If a

number is sent within 200 msecs

before the BEL character, the

scanner will beep that number of

times.

*Disable Light Pen Toggle During

Beep

Enable Light Pen Toggle During

Beep

116913

116903

Whenenabled,thescannerbeepsandtog-

gles thelightpendatalineonasuccessful

decode. Thisdrives agoodreadindicator.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Data Transmission Delays

Use these codes to select the amount of delay between sending data characters and “Bar code” Records from the scan-

ner to the host. This helps prevent the scanner from overflowing host input buffers.

Intercharacter Delay Options

10 msec Intercharacter Delay

8188100

*1 msec Intercharacter Delay

818810

25 msec Intercharacter Delay

~Variable msec Intercharacter Delay

918800

8188250

Scanthisbarcodeandasequenceofcode

bytes in Section M to set the delay

betweencharacterssenttothehost

system. (Range from 1 to 255 msecs.)

RefertotheMultiCodeMethodonpageiii.

D-14

Download from Www.Somanuals.com. All Manuals Search And Download.

D-15

MetroSelect^™

No Intercharacter Delay

818800

Inter-Record Delay

~Variable Inter-Record Delay

919300

*Leave Laser On During

Inter-Record Delay

Turn Off Laser During Inter-

Record Delay

119317

119307

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Communication Timeout Options

Enable Communications

Time Outs

*Disable Communications

118412

118402

Beep After

Transmit

*Beep Before

Transmit

118413

118403

Scanner will beep after each label is trans-

mitted.

Scanner will beep after each label is trans-

mitted.

~Variable Communications Time Out

919100

*Default Communications Time Out

(2 secs)

8191400

D-16

Download from Www.Somanuals.com. All Manuals Search And Download.

D-17

MetroSelect^™

Short Communications Time Out

(1 secs)

Long Communications Time Out

(4 secs)

8191200

8191800

Three Beeps on

Time Out

*No Beeps on

Time Out

118410

118400

*No Razzberry Tone on Time

Out

Razzberry Tone on Time Out

118411

118401

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Host Scanner Commands

Enable “D/E” Disable Command

118115

*Disable “D/E” Disable

118105

When this option is chosen, the scan-

ner will disable scanning after it

receives an ASCII “D” from the host

device. It will enable scanning when

it receives an ASCII “E.”

Donot monitorD/E commands.

Enable Z/R Type D/E Simulation

118211

*No “Z/R” Type “D/E”

Simulation

118201

When this option is chosen, the

scanner will disable scanning after it

receives an ASCII “Z” from the host

device. It will enable scanning when it

receives an ASCII “R.”

Do not monitorZ/R commands.

D-18

Download from Www.Somanuals.com. All Manuals Search And Download.

D-19

MetroSelect^™

Enable “F/L” Laser Command

118014

*Disable “F/L” Laser Command

118004

When enabled, the scanner will turn

off the laser after the scanner

receives an ASCII “F” character. The

laser will turn on after it receives an

ASCII “L” character.

Do not monitor “F/L” commands.

Motor On/Off Using

M/O Commands

*Disable M/O

Commands

118213

118203

When enabled, the motor will turn on

after the scanner receives an ASCII

“M” character. The scanner will turn

off the laser and motor after it

receives an ASCII “O” character.

For use with omnidirectional

scanners only.

Do not monitor M/ O commands.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Use DTRScan Disable

*Do not use DTRScan Disable

118115

118105

Do not monitor the DTR input.

When enabled, the scanner will

monitor the DTR input to determine if

scanning should be allowed. A +12V

“active” level enables decoding.

A -12V “inactive” level disables

decoding.

_{Download from Www.Somanuals.com.}D_A-_ll2_M0_{anuals Search And Download.}

D-21

MetroSelect^™

Activate on DC2 Character

*Do Not Activate on DC2

Character

118110

118100

Transmit “NO READ” if DC2

Activated

Do Not Transmit “NO READ” if

DC2 Activated

118111

118101

No Green LED During

“NO READ” Xmit

*Green LED During “NOREAD”

Xmit

118311

118301

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Power Save Modes

Always Power Save Mode

118617

No Power Save

Mode

818600

Enters power save mode immediately

after power-up and after each bar

code scanned. For use with

Omnidirectional scanners only.

The scanner will never enter power

save mode. For use with

Omnidirectional scanners only.

Power Save in

2 Minutes

Power Save Mode in

1 Minute

118610

818620

Enters power save mode when the scanner

remains idle for 1 minute. For use with

Omnidirectional scanners only.

Enters power save mode if the scanner

remains idle for 2 minutes. For use

with Omnidirectional scanners

only.

D-22

Download from Www.Somanuals.com. All Manuals Search And Download.

D-23

MetroSelect^™

Power Save in

5 Minutes

Power Save in

10 Minutes

8186100

818650

Enterspowersavemodeifthescannerremains

idle for 10 minutes. For use with

Omnidirectional scanners only.

Enters power save mode if the scanner

remains idle for 5 minutes. For use

with Omnidirectional scanners

only.

Power Save in

30 Minutes

Power Save in

20 Minutes

8186200

8186300

Enterspowersavemodeifthescanner

remainsidle for30minutes. For use

with Omnidirectional scanners

Enterspowersavemodeifthe scanner

remainsidlefor20minutes. For use

with Omnidirectional scanners

only.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Miscellaneous Features

Enable Japan Mode

118112

*Disable Japan Mode

118102

_{Download from Www.Somanuals.com.}D_Al-_l2_M4_{anuals Search And Download.}

D-25

MetroSelect^™

Test Modes

Scanability ON

*Scanability OFF

118017

118007

This option enters scanability test mode. Do

not enable unless instructed by a

Metrologic representative.

Scan Count Mode ON

118016

*Scan Count Mode OFF

118006

When enabled, the scanner willenter scan

count test mode and the scanner’s

firmwaer numberwilltransmit tothehost.

Do not enable unless instructed by a

Metrologic representative.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section E

Prefixes/ Suffixes

User Configurable Prefixes, All Data

User Configurable ID Characters, Code Specific

Standard Prefix Characters

E-1

E-3

E-8

Standard Suffix Characters

E-13

E-15

E-16

E-19

Longitudinal Redundancy Check (LRC)

User Configurable Suffixes, All Data

Special Formats

Download from Www.Somanuals.com. All Manuals Search And Download.

E-1

MetroSelect^™

User Configurable Prefixes, All Data

Note: Scan “Enter configuration mode” code before trying to set this feature. Please refer to

MultiCode Method pn page iii.

~Configurable Prefix

Character #1

~Configurable Prefix

Character #2

903500

903600

When this option is chosen, a prefix

ID can be added and assigned for

data transmission. Use this code with

a 3 code byte sequence from

Section M that represents the

desired character.

Assigns a second configurable prefix

character.

~Configurable Prefix Character

~Configurable Prefix

Character #3

903700

903800

Assigns a fourth configurable prefix

character.

Assignsathirdconfigurableprefixcharacter.

~Configurable Prefix

Character #5

~Configurable Prefix

Character #6

904000

903900

Assignsasixthconfigurableprefixcharacter.

Assignsafifth configurable prefixcharacter.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

~Configurable Prefix

Character #7

~Configurable Prefix

Character #8

904100

904200

Assigns a seventh configurable prefix

character.

Assigns an eighth configurable prefix

character.

~Configurable Prefix

Character #10

~Configurable Prefix

Character #9

904300

904400

Assignsatenthconfigurableprefix

characte.r

Assignsaninthconfigurableprefix

characte.r

*Clear All User Configurable

Prefixes

999985

_{Download from Www.Somanuals.com. All Manuals S}E-_e2_{arch And Download.}

E-3

MetroSelect^™

User Configurable ID Characters, Code Specific

*Use Configurable Code ID Bytes

as Prefixes

Use Configurable Code ID Bytes

as Suffixes

105507

105517

User configured, codespecific IDbytes

are transmitted after the data. If

using suffixes, user configured

prefixes can not be used.

User configured, code specific ID bytes

are transmitted before the data. If

using prefixes, user configured

suffixes can not be used.

Identifiers Characters

Configurable

UPC-A ID

Configurable

UPC-E ID

905600

905700

While using the MultiCode Method, scan

this bar code followed by the 3 code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

While using the MultiCode Method, scan

this bar code followed by the 3 code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Configurable

EAN-8 ID

Configurable

EAN-13 ID

905800

905900

While inusing theMultiCodeMethod, scan

this bar code followed by the 3code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

While inusing theMultiCodeMethod, scan

this bar code followed by the 3code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Configurable

Code 128 ID

Configurable

Code 39 ID

906000

906100

While inusingthe MultiCodeMethod, scan

this bar code followed by the 3code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

While inusingtheMultiCodeMethod, scan

this bar code followedby the 3 code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

_{Download from Www.Somanuals.com. All Manuals}E_S-_e4_{arch And Download.}

E-5

MetroSelect^™

Configurable

Code 93 ID

Configurable

Code 11 ID

906300

906400

Whileinusingthe MultiCode Method, scan

this bar code followed by the 3 code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Whileinusingthe MultiCode Method, scan

this bar code followed by the 3 code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Configurable

Telepen ID

Configurable

TRI-OPTIC ID

906200

907200

While inusing theMultiCodeMethod, scan

this bar code followed by the 3code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

While inusing theMultiCodeMethod, scan

this bar code followed by the 3code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Configurable

Interleaved 2 of 5 ID

Configurable

Standard 2 of 5 ID

907100

906700

While inusingthe MultiCode Method, scan

thisbar codefollowed by the 3 codebyte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Whileinusingthe MultiCode Method, scan

thisbar codefollowed by the 3 codebyte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Configurable

Airline 2 of 5 ID

Matrix 2 of 5 ID

906800

906900

Whileinusing theMultiCodeMethod, scan

this bar code followed by the 3 code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Whileinusing theMultiCodeMethod, scan

this bar code followed by the 3 code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

E-6

Download from Www.Somanuals.com. All Manuals Search And Download.

E-7

MetroSelect^™

Configurable

UK Plessey ID

Configurable

MSI Plessey ID

906500

907000

While inusingthe MultiCode Method, scan

thisbar codefollowed by the 3 codebyte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Whileinusingthe MultiCode Method, scan

thisbar codefollowed by the 3 codebyte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

*Clear all Configurable Code

Specific ID’s

Configurable

Codabar ID

906600

999983

While inusingtheMultiCodeMethod, scan

this bar code followed by the 3 code byte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

While inusingtheMultiCodeMethod, scan

this bar code followed by the 3 codebyte

bar codes in Section M that represent a

unique ID character to be associated with

this bar code type. Please refer to

MultiCodeMethodonpageiii.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Standard Prefix Characters

Enable STX Prefix

116615

*Disable STX Prefix

116605

Will not transmit a Start of TeXt

(ASCII 02H) before each bar code.

When enabled, the scanner will trans-

mit a Start of TeXt (ASCII 02H)

before each bar code.

Enable Rochford-Thomson Mode

105513

*Disable Rochford-Thomson Mode

105503

*Disable AIM ID Characters

107905

Enable AIM ID Characters

107915

The scanner will transmit AIM

symbology identifiers. Some scan-

ners may not support this feature

The scanner will not transmit AIM

symbology identifiers.

E-8

Download from Www.Somanuals.com. All Manuals Search And Download.

E-9

MetroSelect^™

Enable UPC Prefix ID

*Disable UPCPrefix ID

116617

116607

Do not send prefix ID Characters with

UPC/EAN codes.

When enabled, the scanner will

transmit a prefix before any UPC/EAN

bar code. The prefixes are A (UPC-A),

E0 (UPC-E), F (EAN-13), and

FF (EAN-8).

Enable NCR Prefix ID

107911

*Disable NCR Prefix ID

107901

When enabled, the scanner will transmit a

prefix before the following code types.

The prefixes are as follows:

A (UPC-A)

E0 (UPC-E)

FF (EAN-8)

F (EAN 13)

B1 (Code 39)

B2 (ITF)

B3 (Code 128 and other codes)

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable Nixdorf ID Characters

107917

*Disable Nixdorf ID Characters

107907

This bar code will not transmit

Siemens/Nixdofrcode identifiers.

When enabled, this option transmits

code identifiers before each bar code

for many Siemens/Nixdorf registers.

*Disable SANYO ID Characters

107906

Enable SANYO ID Characters

107916

Transmit Sanyo ID Characters.

Do not transmit Sanyo ID Characters.

_{Download from Www.Somanuals.com. All Manuals}E_S-_e1_a0_{rch And Download.}

E-11

MetroSelect^™

*Disable Manufacturer ID Prefix

Enable Manufacturer ID Prefix

105512

105502

Transmits “METROLOGIC” before all bar

code data to identify the scanner as a

Metrologicscanner.

Will not transmit the identification

string.

*Disable “C” Prefix

105501

Enable “C” Prefix

105511

Enable “$” Prefix ID for

UPC/EAN

*Disable “$” Prefix ID for

UPC/EAN

105510

105500

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable Tab Prefix

*Disable Tab Prefix

116611

116601

Will not transmit a TAB.

The Scanner will transmit a TAB

(ASCII 09H) before each bar code.

*Disable SNI Beetle Mode

116101

Enable SNI Beetle Mode

116111

Enable Cipher 1021 IDs

116113

*Disable Cipher 1021 IDs

116103

_{Download from Www.Somanuals.com. All Manuals}E_S-1_ea2_{rch And Download.}

E-13

MetroSelect^™

Standard Suffix Characters

Disable CR Suffix

*Enable CR Suffix

116613

116603

The scanner will not transmit a

Carriage Return after each bar

code.

When enabled, the scanner transmits a

Carriage Return after each bar code.

*Enable LF Suffix

116612

Disable LF Suffix

116602

When enabled, the scanner transmits

a Line Feed after each bar code.

Note: Disabled when keyboard

wedge defaults are loaded.

The scanner will not transmit a Line

Feed after each bar code.

Enable Tab Suffix

116610

*Disable Tab Suffix

116600

When enabled, the scanner will

transmit a TAB (ASCII 09H) after

each bar code.

Will not transmit TAB (ASCII 09H)

after each bar code.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable ETX Suffix

*Disable ETX Suffix

116614

116604

When enabled, the scanner will

transmit End of TeXt (ASCII 03H)

after the bar code data.

When disabled, the scanner will not

transmit End of TeXt (ASCII 03H).

Enable UPC Suffix ID

116616

*Disable UPC Suffix ID

116606

When enabled, the scanner will

transmit a suffix after any UPC/EAN

bar code. The suffixes are A (UPC-

A), E (UPC-E), F (EAN-13) and

F (EAN-8).

Will not transmit a suffix after

UPC/EAN bar codes.

_{Download from Www.Somanuals.com. All Manuals}E_S-1_ea4_{rch And Download.}

E-15

MetroSelect^™

Longitudinal Redundancy Check (LRC)

*Disable Transmit of LRC

Calculation

Enable Transmit of LRC

Calculation

107811

107801

Will not output an LRC (check

character) after the bar code.

With this option, the scanner outputs

an LRC check character after the bar

code.

Start LRC on

Second Byte

*Start LRC on

First Byte

107810

107800

Thescannerwillcalculate the LRCcheck

digit startingwith the firstcharacter

ThescannerwillcalculatetheLRCcheck

digit starting with thesecond character.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

User Configurable Suffixes, All Data

Note: Scan “Enter configuration mode” code before trying to set this feature. Refer to

MultiCode Method on page iii.

~Configurable Suffix

Character #1

~Configurable Suffix

Character #2

904500

904600

When chosen, a suffix ID can be added

and assigned for data transmission.

Use this code with a 3 code byte

sequence from Section M that

Assignsasecondconfigurable suffix

characte.r

represents the desired character.

~Configurable Suffix

Character #4

~Configurable Suffix

Character #3

904700

904800

Assignsafourthconfigurablesuffix

characte.r

Assignsathirdconfigurablesuffix

characte.r

E-16

Download from Www.Somanuals.com. All Manuals Search And Download.

E-17

MetroSelect^™

~Configurable Suffix

Character #5

~Configurable Suffix

Character #6

904900

905000

Assignsafifthconfigurablesuffix character.

Assignsasixthconfigurablesuffixcharacter.

~Configurable Suffix

Character #8

~Configurable Suffix

Character #7

905100

905200

Assignsaseventhconfigurablesuffix

characte.r

Assignsaneighthconfigurablesuffix

characte.r

~Configurable Suffix

Character #10

~Configurable Suffix

Character #9

905300

905400

Assignsatenthconfigurablesuffixcharacter.

Assignsaninth configurable suffixcharacter.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

*Clear All User Configurable

Suffixes

999984

E-18

Download from Www.Somanuals.com. All Manuals Search And Download.

E-19

MetroSelect^™

Special Formats

*Disable SINEKO Mode

Enable SINEKO

Mode

107914

107904

*Disable Newcode Formatting

Mode A

Enable Newcode Formatting

Mode A

116711

116701

*Disable Newcode Formatting

Mode B

Enable Newcode Formatting

Mode B

116710

116700

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section F

Code Formatting

UPC-EAN Formatting

Codabar Formatting

Code 39 Formatting

Code 11

F-1

F-5

F-6

F-7

F-8

F-9

Telepen

Plessey

2 of 5 Code Formatting

_{Download from Www.Somanuals.com. All Manuals Search And}F_Download.

F-1

MetroSelect^™

UPC/ EAN Formatting

*Transmit UPC-A

Check Digit

Do Not Transmit UPC-A

Check Digit

116617

116607

Transmit UPC-E

Check Digit

*Do Not Transmit UPC-E

Check Digit

107516

107506

Expand UPC-E to

12 Digits

*Do Not Expand UPC-E to

12 Digits

107515

107505

Expand UPC-E bar codes to the 12 digit

equivalent, UPC-A bar codes.

Do not expand UPC-E to the 12 digit

equivalent, UPC-A bar code.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Convert UPC-A to EAN-13

107514

*Do Not Convert UPC-A to EAN-13

107504

With this option, the scanner converts

UPC-A to EAN-13 by transmitting a lead-

ing zero before the bar code.

With this option, the scanner will not

convert UPC-A to EAN-13.

Transmit Lead Zero on UPC-E

107513

Do Not Transmit Lead Zero on

UPC-E

107503

This option will not transmit a zero

before each UPC-E bar code.

When chosen, this option will transmit

a zero before each UPC-E bar code

Convert EAN-8 to

EAN-13

*Do Not Convert

EAN-8 to EAN-13

107512

107502

When chosen, the scanner will trans-

mit five zeros before the bar code to

convert EAN-8 to Ean-13.

When chosen, the scanner will not

convert EAN-8 to Ean-13.

F-2

Download from Www.Somanuals.com. All Manuals Search And Download.

F-3

MetroSelect^™

Do Not Transmit UPC-A

Number System

*Transmit UPC-A

Number System

107511

107501

Metrologic strongly discourages using

this feature. Duplicate numbers may

result in the database.

*Transmit UPC-A MFR#

Do Not Transmit

UPC-A MFR#

107611

107601

*Transmit UPC-A ITEM#

Do Not Transmit

UPC-A ITEM#

107610

107600

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Do Not Transmit EAN-8

Check Digit

*Transmit EAN-8

Check Digit

107910

107900

Do Not Transmit

*Transmit EAN-13 Check Digit

EAN-13 Check Digit

107912

107902

Scanner will not transmit EAN-13

Check Digit.

Scanner will transmit EAN-13

Check Digit.

_{Download from Www.Somanuals.com. All Manuals Search An}F_d-_D4_ownload.

F-5

MetroSelect^™

Codabar Formatting

*Do Not Transmit Codabar

Start/Stop

Transmit Codabar Start/Stop

Characters

107717

107707

Will not transmit Codabar’s start/stop

characters before and after each bar

code.

Transmits Codabar’s start/stop

characters before and after each

bar code.

Enable CLSI Editing

107716

*Do Not Enable

CLSI Editing

107706

Works only with 14 digit Codabar type

lengths. This option will perform CLSI

type editing before the information is

transmitted to the host.

This optionwill notperform CLSI

type editing before the information is

transmitted to thehost.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Code 39 Formatting

Transmit Mod 43 Check

Digit On Code 39

*Do Not Transmit Mod 43 Check

Digit On Code 39

107715

107705

ThisoptionwillnottransmitCode39’sMod

43checkcharacter.

This feature works in conjunction with

Mod43CheckonCode 39optionin

sectionA. Both must be enabled for this

featuretowork.

Transmit Code 39

Stop/Start Characters

*Do Not Transmit Code 39

107700

107710

When chosen, the scanner transmits

Code 39’s start and stop characters

before and after each bar code.

When chosen, the scanner will not

transmit Code 39’s start and stop

characters before and after each bar

code.

F-6

Download from Www.Somanuals.com. All Manuals Search And Download.

F-7

MetroSelect^™

Code 11

*Do Not Transmit Code 11

Check Digit

Transmit Code 11 Check Digit

107713

107703

This bar code will transmit Code 11

check characters when used with

Enabled Code 11 in section A.

This bar code will not transmit Code

11check characters.

Telepen

*Disable Convert

Telepen ^L to E

Enable Convert

Telepen ^L to E

107814

107804

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Plessey

Transmit UK Plessey Check Digit

107816

*Do Not Transmit UK Plessey

Check Digit

107806

The scanner will transmit UK

Plessey CheckDigitcharacters and

must beused with the UK Plessey option.

WillnottransmitUKPlesseyCheck

Digitcharacters.

Disable UK Plessey

Special Format

Enable UK Plessey

Special Format

107815

107805

* Do Not Transmit MSI Plessey

Check Digit

Transmit MSI Plessey

Check Digit

107711

107701

This option works in conjunction with

one or both of the Enabled MSI Plessey

Mod options in Section A.

The scanner will not transit MSI

Plessey’s check digit characters.

F-8

Download from Www.Somanuals.com. All Manuals Search And Download.

F-9

MetroSelect^™

2 of 5 Code Formatting

*Do not Transmit Mod 10 Check

Digit on ITF

Transmit Mod 10 Check Digit

on ITF

107714

107704

The scanner will nottransmit Interleaved

2 of 5 (ITF) Mod 10 check character.

Works in conjunction with Mod 10 check

on ITF. Both must be enable for this fea-

ture to work.

With this option, the scanner transmits

Interleaved 2 of 5 (ITF) Mod 10 check

characte.r

*Do Not Transmit Matrix 2 of

5 Check Digit

Transmit Matrix 2 of 5

Check Digit

107812

107802

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section G

RS-232

Enable RS-232

G-1

G-2

G-3

G-5

G-6

G-9

G-11

Parity Features

BAUD Rate Features

Data/Stop Bit Features

Hardware Handshaking

Software Handshaking

Miscellaneous

Download from Www.Somanuals.com. All Manuals Search And Download.

G-1

MetroSelect^™

*Enable RS-232 Mode

415554

When enabled the scanner will

work with RS-232 +/-12V serial

output.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Parity Features

A parity bit is an extra data bit used to help catch data transmission errors.

The scanner’s parity must match the host’s parity.

No Parity

316045

Odd Parity

316005

*Space Parity

316015

Select Odd Parity to set the

parity bit to either a 1 or a 0 to

ensure an odd number of bits are

1’s.

Select Space Parity to set the

parity bit always 0.

Even Parity

316025

Mark Parity

316035

Select Mark Parity to set the parity bit

always 1.

SelectEven Paritytoset the parity bitto

either a 1 or0 to ensure an evennum-

ber of bits are 1’s.

G-2

Download from Www.Somanuals.com. All Manuals Search And Download.

G-3

MetroSelect^™

BAUD Rate

A “BAUD” or “BAUD Rate” is the speed at which data is transmitted. Select a BAUD for the scanner that matches

the host device.

57600 BAUD Rate

115200 BAUD Rate

4158100

415890

Not supported on the

MS9500 Voyager.^™

Not supported on the

MS9500 Voyager.^™

19200 BAUD Rate

38400 BAUD Rate

415880

415870

14400 BAUD Rate

*9600 BAUD Rate

415860

415850

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

4800 BAUD Rate

2400 BAUD Rate

415840

415830

600 BAUD Rate

1200 BAUD Rate

415820

415810

300 BAUD Rate

415800

_{Download from Www.Somanuals.com. All Manuals Search And Downloa}G_d.-4

G-5

MetroSelect^™

Data/ Stop Bits

*7 Data Bits

8 Data Bits

116013

116003

Number of data bits transmitted for

each character.

*2 Stop Bits

1 Stop Bit

116014

116004

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Hardware Handshaking

*Disable RTS/CTS Handshaking

115806

Enable RTS/CTS Handshaking

115816

OutputaRequestToSend

DonotuseRTS/CTShandshaking.

(RTS) signaland wait for a Clear To Send

(CTS)signalbeforetransmittingdata.

Message RTS/CTS

115805

*Character RTS/CTS

115815

Activate RTSbefore sendingthefirstchar-

acterandleaveitactiveuntilafterthelast

characterhasbeentransmitted.

Activate/Deactivate RTS signal for each

characte.r

Invert RTS Polarity (RSV1)

124510

*Standard RTS Polarity

124500

+12v=Inactive

-12v=Active

UsestandardRTSpolarity

-12v=Inactive

+12v=Active

_{Download from Www.Somanuals.com. All Manuals Search And Downloa}G_d.-6

G-7

MetroSelect^™

Invert CTS Polarity (RSV2)

124511

*Standard CTS Polarity

124501

-12v = Inactive, do not send

+12v = Active, OK to send

+12v = Inactive, do not send

-12v = Active, OK to send

Activate RTS,

Do Not wait for CTS (RSV3)

*Activate RTS, Wait for CTS

124502

124512

Wait for CTSafter activating RTS.

Activate RTS for transmission but, do

not wait for CTS to send.

*Do Not Test for CTS Present

Before RTS

Test CTS Not Present

Before RTS (RSV4)

124513

124503

Do not activate RTS if CTS is already

present.

Activate RTS without testingif CTS is

already active.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable DTR Support

*Disable DTR Support

115817

115807

When enabled the scanner will stop

scanning when the Data Terminal Ready

(DTR) signal goes inactive.

Enable RTS Counter Toggle

115915

*Disable RTS Counter Toggle

115905

The scanner will toggle the RTS line on a

gooddecode.

G-8

Download from Www.Somanuals.com. All Manuals Search And Download.

G-9

MetroSelect^™

Software Handshaking

Enable XON/XOFF Handshaking

115914

*Disable XON/XOFF Handshaking

115904

When enabled, the scanner will stop

transmission whenever an XOFF

(ASCII 13H) is received. Transmission

will resume after an XON(ASCII 11H) is

received.

Thescanner will not test for XON/XOFF.

*Disable ACK/NAK

115903

Enable ACK/NAK

115913

After transmitting data, wait for an ACK

(06H)or a NAK(15H)responsefromthe

host. If ACK is received, complete the

communications cycle and look for more

bar codes. IF NAK is received, retransmit

the last set of bar code data and wait for

ACK/NAK again.

Do not support ACK/NAK handshaking.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

*Ignore BEL/CAN in ACK/NAK

115901

Support BEL/CAN in ACK/NAK

115911

When BEL (07H) is received, the

scanner beeps 3 times and exits the

communicationsloop. IfaCAN (18H)is

received, then the scanner will exit the

communications loop, silently.

Ignore BEL/CAN characters in

communication loop.

Enable 5 Retries on ACK/NAK

Time Out

*Disable 5 Retries on ACK/NAK

Time Out

118013

118003

Allow up to 5 NAK retransmissions of

the data before dropping out of the

communications loop.

Donot limit retransmission to 5NAK

cycles.

G-10

Download from Www.Somanuals.com. All Manuals Search And Download.

G-11

MetroSelect^™

Miscellaneous

*Disable French PC Term

Enable French PC Term

116110

116100

DonottransmitinFrenchPCTermmode.

Whenenabled,thescannertransmitsPCtype

make/berak scan codes instead of ASCII

data characters. The scan codes match a

WYSEFrenchPC TermTerminalEmulation.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section H

Keyboard

Enable Keyboard Emulations

H-1

H-2

H-4

H-5

H-8

H-9

Country/Scan Code Table Selects

Keyboard/System Type

Special Keyboard Features

InterScan Code Delays

Control Sets

Download from Www.Somanuals.com. All Manuals Search And Download.

H-1

MetroSelect^™

Enable Keyboard Emulation

Load Keyboard Wedge Defaults

999994

Loads default settings for keyboard wedge

mode.

Enable Stand-Alone Keyboard

Emulation

*Enable Keyboard Wedge

Emulation

5155153

415574

Use this with an external keyboard.

Transmit in wedge mode to allow stan-

dard PC Keyboards to communicate

when no bar code data is available.

Usethiswithspecialstand-alonemodelsthat

are not cabled for an external keyboard.

Scanthisbarcode toenabletheStand-Alone

Mode. The scanner will send keyboard

“power on” information and configure

hardware to simulate a constant keyboard

connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Country/ Scan Code Table Selects

Switzerland Keyboard

*USA Keyboard

416240

416280

Enable USA Keyboard.

EnableSwiss Keyboard.

Spain Keyboard

416250

Italy Keyboard

416240

Enable Italian Keyboard.

Enable Spanish Keyboard.

Germany Keyboard

416230

France Keyboard

416220

Enable French Keyboard.

Enable German Keyboard.

H-2

Download from Www.Somanuals.com. All Manuals Search And Download.

H-3

MetroSelect^™

UK Keyboard

Belgium Keyboard

416210

416200

Enable UK Keyboard.

Enable Belgium Keyboard.

Japanese Keyboard

IBM 4700 Financial Keyboard

416270

4162100

Enable Japanese Keyboard.

Enable IBM 4700 Financial

Keyboard.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Keyboard/ System Type

*AT Keyboard

216215

If using an AT computer, scan the

above. (Includes IBM PS/2 and

compatible models 50, 55, 60, 80)

PS/2 Keyboard

216225

XT Keyboard

216205

Scan the above for PS/ 2 computer.

(Includes IBM PC and compatible models

30, 70, 8556)

If usinganXTcomputer, scantheabove.

H-4

Download from Www.Somanuals.com. All Manuals Search And Download.

H-5

MetroSelect^™

Special Keyboard Features

Transmit Make Code Only

116311

*Transmit Make/Break Code

116301

Do not scan unless instructed by a

Metrologicrepresentative.

Do not scan unless instructed by a

Metrologic representative.

Do Not Transmit F0H Break Code

116300

*Transmit F0H Break Code

116310

The scanner will not transmit the F0H

in the break-code sequence.

The scanner will transmit the F0H

in the break-code sequence.

Transmit Cleanup Bit

116315

*Do Not Transmit Cleanup Bit

116305

Use for certainNEC computers.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Enable Alt Mode

*Disable Alt Mode

116217

116207

Caution: If host software application

uses the right Alt key as a “Hot” key.

Alt mode must be disabled.

When enabled, the scanner will

duplicate this keyboard sequence:

Hold down ALT key: Type decimal number that

corresponds to the appropriate character.

Enable Auto Detect Mode

(AT/PS2)

*Disable Auto Detect Mode

(AT/PS2)

116214

116204

Automatically detects caps lock status.

When disabled, theCapsLockfeature is

notsupported.

Enable Caps Lock (XT)

116315

*Disable Caps Lock (XT)

116305

When disabled, theCapsLockfeature

isnotsupported.

H-6

Download from Www.Somanuals.com. All Manuals Search And Download.

H-7

MetroSelect^™

Send Numbers as Keypad Data

116316

*Send Numbers as Normal Data

116306

Whenenabled, alldatais sentasif ithas been

enteredonakeypad.

Enable Reserved Feature

116410

*Disable Reserved Feature

116400

Use Extended ASCII Characters

As Extended ASCII

*Use Extended ASCII To Send

Extended Key Codes

116303

116313

Use extended ASCII characters to

send PC keyboard keys such as F1,

F2, etc...See section M for details.

Transmit extended ASCII codes via

ALT Mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Message KB Inhibit

116314

*Character KBInhibit

116304

InterScan Code Delays

*InterScan Code Delay 800

Microseconds

InterScan Code Delay 7.5 msec

8165750

816580

The time specifiedrepresentstheamount

of time between individual 9 bit-scan

codes. This parameter may need to be

adjusted for operation with certain PC

keyboadr BIOS.

The time specifiedrepresentstheamount

of time between individual 9 bit-scan

codes. This parameter may need to be

adjusted for operation with certain PC

keyboadr BIOS.

~Variable InterScan Code

Delay msec

InterScan Code Delay

15 msec

81651500

916500

RefertoMulti-CodeMethodonpageiii.

Thetimespecifiedrepresentstheamount oftime

betweenindividual9bit-scancodes. Thisparam-

eter mayneed tobe adjusted for operation with

certainPCkeyboardBIOS.

H-8

Download from Www.Somanuals.com. All Manuals Search And Download.

H-9

MetroSelect^™

Control Sets

In general, standard bar code symbologies will only encode the ASCII character set. Function keys, arrow keys and

many other “extended” keys on an IBMcompatible keyboard do not translate to ASCII characters. One method of

“bar coding” the extended keys is to substitute the extended key codes when a specific ASCIIcontrol character is

found in the bar code stream. The Control Sets are specific translations of the ASCII (HEX) set.

Control Set #1

Disable Control Set #1

Enable Control Set #1

416484

416404

ASCII (HEX)

Extended Key

Numeric Keypad

ASCII Control

00H

01H

02H

03H

04H

05H

06H

07H

08H

09H

Null

SOH

STX

ETX

EOT

ENQ

ACK

BEL

Num Lock

Down

Numeric Keypad-

Insert

Delete

System Request

➝

Tab

TAB

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Control Set #1 Continued

Extended Key

Caps Lock

ASCII (HEX)

ASCII Control

0AH

0BH

0CH

0DH

0EH

0FH

10H

11H

12H

13H

14H

15H

16H

17H

18H

19H

1AH

1BH

1CH

1DH

1EH

1FH

Shift Tab

Alt

Enter

Control

Up Arrow

DLE

DC1

DC2

DC3

DC4

NAK

SYN

ETB

CAN

SUB

ESC

F10

Home

Esc

Page UP

Page Down

Print Screen

End

H-10 _{Download from Www.Somanuals.com. All Manuals Search And Download.}

H-11

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section I

OCIA

I-1

Load OCIA Defaults

DTS/Nixdorf

DTS/Siemens

NCR-S

NCR-F

_DownloI_{ad from Www.Somanuals.com. All Manuals Search And Download.}

I-1

MetroSelect^™

Enable OCIA Mode

Load OCIA Defaults

999993

415544

Select this option if communications

requires OCIA (Optically Coupled

Interface Adapter). This serial inter-

face is clocked by the host.

*Enable DTS/Nixdorf

Enable DTS/Siemens

217706

217716

Enable NCR-S

217736

Enable NCR-F

217726

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section J

Light Pen Parameters

Enable Light Pen Mode

Spaces/Bar High

J-1

J-2

J-3

Transmit as Scanned/Code 39

Poll Light Pen Source

Light Pen Extra Toggle

10x Narrow Element Border

50x Narrow Element Border

Set Narrow Element Width

_{Download from W}J_{ww.Somanuals.com. All Manuals Search And Download.}

J-1

MetroSelect^™

Enable Light Pen Mode

415524

Select this option if the scanner will be

used in place of a light pen. It provides

light pen emulation of each bar code

scanned.

Spaces High

116907

*Bars High

116917

Transmit Code 39

*Transmit as Scanned

116906

116916

All bar codes will be decoded then

transmitted as code 39 bar codes.

All bar codes will be decoded and

transmitted in that symbology.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Poll Light

Pen Source

*Do Not Poll Light

Pen Source

116915

116905

When chosen, the scanner will not wait

foranactivesource voltagebefore

transmittingdata.

When chosen, the scanner waits for

an active source voltage before

transmitting data.

Enable Light Pen Extra Toggle

116911

*Disable Light Pen Extra Toggle

116901

When enabled, the scanner beeps and tog-

gles the light pen data line with an extra

datapulsetoconditionthedecoder.

10x Narrow Element Border

116912

*50x Narrow Element Border

116902

This bar code allows the transmission of

LightPen/Wandemulationusinga

50xborder.

This bar code allows the transmission of

Light Pen/Wand emulation using a 10x

borde.r

_{Download from W}J-2_{ww.Somanuals.com. All Manuals Search And Download.}

J-3

MetroSelect^™

Set Narrow Element Width

*1 ms Narrow

Element Width

60 µs Narrow

Element Width

81681630

8168100

Thistransmitsat60µsNarrowelementwidth.

This option allows the transmission of

Light/Pen Wand emulation at 1ms

Narrow Element width.

100 µs Narrow

Element Width

500 µs Narrow Element Width

8168820

8168160

This transmits at 100 µs Narrow element

width.

This transmits at 500 µs Narrow element

width.

~Variable Narrow Element Width

916800

Sets the minimum x-dimension in 6 µs

increments. Scanthiscodefollowedbya3

digit code byte sequence found in Section

M. RefertoMultiCodeMethodonpageiii.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section K

IBM 46xx Configuration

IBM Port

K-1

K-2

IBM Reserved Codes

_{Download from Www.Soman}K_{uals.com. All Manuals Search And Download.}

K-1

MetroSelect^™

Load 46xx

IBM Defaults

Enable IBM 46xx Communication

415504

999995

Load default format

Select this option for IBM 46XX

SIOC/RS485 communications. Not all

scannerssupportthisinterface.Thecorrect

interfaceboardis required.

settings for the IBM 46xx systems.

IBM Port

IBM Port 5B

IBM Port 17B

1520 HH Laser

3687-2 In Counter

317250

317260

IBM Port 9B

4500 CCD HH BCRI

317270

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

IBM Reserved Codes

IBM Reserved #2

IBM Reserved #1

317200

317210

IBM Reserved #4

IBM Reserved #3

317220

317230

IBM Reserved #5

317240

K-2

Download from Www.Somanuals.com. All Manuals Search And Download.

K-3

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section L

MS9500 Voyager^™

Activation Range

L-1

L-2

L-3

L-4

CodeGate^™Status

Laser/Scan Modes

Same Symbol Time Outs

Download from Www.Somanuals.com. All Manuals Search And Download.

L-1

MetroSelect^™

Activation Range

Use these bar codes to select infrared (IR) sensor activation range for sensing when objects are placed in the

scan field.

*Long Range in Stand

Short Range in Stand

118715

118705

Short Range out of Stand

*Long Range out of Stand

118711

118701

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

CodeGate^™Status

Use the following to control button functions.

CodeGate Active in the Stand

118707

*CodeGate Inactive in the Stand

118717

CodeGate Inactive Out of Stand

118703

*CodeGate Active Out of Stand

118713

_{Download from Www.Somanuals.com}L_.-_A2_{ll Manuals Search And Download.}

L-3

MetroSelect^™

Laser/ Scan Modes

*Normal Scan

418304

Laser turns on after the IR senses a

bar code. The laser remains on for

approximately 3 to 10 seconds.

Blinky Scan

418324

Continuous Blinky Scan

418334

Laser turns on after the IR senses a

bar code. The laser will blink on/off

for approximately 60 seconds.

The laser blinks continuously. The IR

is inactive.

Custom (One Shot) Scan

418344

Laser turns on after the IR senses a

bar code. The laser will turn off

after a good decode.

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Same Symbol Time Outs

No Same Symbol

Time Out

1000 msec Same Symbol

Time Out

318910

818900

750 msec Same Symbol

Time Out

*875 msec Same Symbol

Time Out

318930

318920

625 msec Same Symbol

Time Out

500 msec Same Symbol

Time Out

318950

318940

_{Download from Www.Somanuals.com}L_.-_A4_{ll Manuals Search And Download.}

L-5

MetroSelect^™

250 msec Same Symbol

Time Out

375 msec Same Symbol

Time Out

318970

318960

Infinite Same Symbol

Time Out

118917

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section M

Code Bytes

Code Byte Usage

Code Bytes 0-5

Code Bytes 6-9

Reserved Codes

M-1

M-2

M-3

M-4

M-5

M-6

M-11

Code Byte/Code Type Table

ASCII Reference Table

Extended Key Code Reference Table

Download from Www.Somanuals.com. All Manuals Search And Download.

M-1

MetroSelect^™

Code Byte Usage

NOTE!

User Configurable Prefixes, Symbol Length and other features that use these Code Bytes for configura-

tion, require that the scanner be in Configuration Mode. Scan the Enter/Exit Configuration Mode bar

code before starting the configuration cycle. Single Code Configuration Mode does not work for these

multi-code sequences.

Example #1

User configurable prefix/suffix characters (section E) can be saved into the scanner by scanning the 3

digit decimal equivalent of the ASCII character into the appropriate character location with the code

byte bar codes.

Add an Asterisk (*) as a Prefix

1. Enter/Exit

(3 beeps)

2. Configurable Prefix #1 (1 beep)

3. Code Byte #0

4. Code Byte #4

5. Code Byte #2

6. Enter/Exit

(1 beep)

(2 beeps)

(3 beeps)

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Code Bytes 0-5

Code Byte 0

Code Byte 1

Code Byte 2

Code Byte 3

Code Byte 4

Code Byte 5

M-2

Download from Www.Somanuals.com. All Manuals Search And Download.

M-3

MetroSelect^™

Code Bytes 6-9

Code Byte 7

Code Byte 6

Code Byte 8

Code Byte 9

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Reserved Codes

~Enable Reserved Code

999988

~Disable Reserved Code

999987

Contact Metrologic for information

about this feature.

M-4

Download from Www.Somanuals.com. All Manuals Search And Download.

M-5

MetroSelect^™

Code Byte/ Code Type Table

Code Byte

Code Types

UPC-A

004

002

003

005

080

081

082

083

084

091

092

093

094

095

096

099

098

097

UPC-E

EAN-8

EAN-13

Code 39

Codabar

Interleaved 2 of 5

Code 128

Code 93

MSI Plessey

Code 11

Airline 2 of 5 (15 digits)

Matrix 2 of 5

Telepen

UK Plessey

TRI-OPTIC

Standard 2 of 5

Airline (13 digits)

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

ASCII Reference Table

Decimal Value/ Code Byte

Value

Control Keyboard

EQV

HEX Value

Character

NUL

SOH

STX

ETX

EOT

ENQ

ACK

BEL

000

001

002

003

004

005

006

007

008

009

010

011

012

013

014

015

016

017

018

019

020

021

022

023

024

025

DLE

DC1

DC2

DC3

DC4

NAK

SYN

ETB

CAN

^{Download from Www.Somanuals.com. All Manu}M^als-6^{Search And Download.}

M-7

MetroSelect^™

ASCII Reference Table

Control Keyboard

EQV

Decimal/ Code Byte Value

HEX Value

Character

026

027

028

029

030

031

032

033

034

035

036

037

038

039

040

041

042

043

044

045

046

047

048

049

050

051

SUB

ESC

[

space, blank

“

‘

apostrophe

(

)

comma

minus

period

number zero

number one

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

ASCII Reference Table

Control Keyboard

EQV

Decimal/ Code Byte Value

HEX Value

Character

052

053

054

055

056

057

058

059

060

061

062

063

064

065

066

067

068

069

070

071

072

073

074

075

076

077

;

less than

greater than

shift P

letter I

M-8

Download from Www.Somanuals.com. All Manuals Search And Download.

M-9

MetroSelect^™

ASCII Reference Table

Control Keyboard

EQV

Decimal/ Code Byte Value

HEX Value

Character

078

079

080

081

082

083

084

085

086

087

088

089

090

091

092

093

094

095

096

097

098

099

100

101

102

103

[

letter O

shift K

shift L

shift M

]

à, shift N

❧, shift O,

underscore

accent grave

‘

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

ASCII Reference Table

Control Keyboard

EQV

Decimal/ Code Byte Value

HEX Value

Character

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

{

vertical slash

alt mode

}

DEL

(alt mode)

delete, rubout

_{Download from Www.Somanuals.com. All Manu}M_als-1_S0_{earch And Download.}

M-11

MetroSelect^™

Extended Key Code Reference Table

XT/ PS2 Scan Code

Prefix/ Suffix Value

Hex = Decimal

At Scan Code

Key

75H

72H

74H

6BH

70H

71H

6CH

69H

7DH

7AH

11H

14H

00H

5AH

4AH

05H

06H

04H

0CH

03H

0BH

83H

0AH

01H

09H

80H = 128

81H = 129

82H = 130

83H = 131

84H = 132

85H = 133

86H = 134

87H = 135

88H = 136

89H = 137

8AH = 138

8BH = 139

8CH = 140

8DH = 141

8EH = 142

8FH = 143

90H = 144

91H = 145

92H = 146

93H = 147

94H = 148

95H = 149

96H = 150

97H = 151

98H = 152

99H = 153

48H

50H

4DH

4BH

52H

53H

47H

4FH

49H

51H

38H

1DH

00H

1CH

35H

3BH

3CH

3DH

3EH

3FH

40H

41H

42H

43H

44H

➝

Insert

Delete

Home

End

Page Up

Page Down

Right Alt

Right Ctrl

Reserved

Numeric Keypad Enter

Numeric Keypad /

F10

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Extended Key Code Reference Table

Prefix/ Suffix Value

Hex = Decimal

XT/ PS2 Scan Code

At Scan Code

Key

57H

58H

4EH

4AH

37H

3AH

45H

38H

1DH

2AH

36H

9AH = 154

9BH = 155

9CH = 156

9DH = 157

9EH = 158

9FH = 159

A0H = 160

A1H = 161

A2H = 162

A3H = 163

A4H = 164

78H

07H

79H

7BH

7CH

58H

77H

11H

14H

12H

59H

F11

F12

Numeric +

Numeric -

Numeric *

Caps Lock

Num Lock

Left Alt

Left Ctrl

Left Shift

Right Shift

A5H = 165

A6H = 166

A7H = 167

A8H = 168

A9H = 169

AAH = 170

ABH = 171

ACH = 172

ADH = 173

AEH = 174

AFH = 175

Multiple

0DH

8DH

5AH

76H

11H

14H

11H

14H

Print Screen

Tab

OFH

8FH

1CH

01H

36H

B6H

1DH

9DH

36H

1DH

Shift Tab

Enter

ESC

Left ALT Make

Left ALT Break

Left CTRL Make

Left CTRL Break

* Left ALT + 1 character

* Left CRTL + 1 character

* Example

1st Configurable Prefix = 174

2nd Configurable Prefix = 065

Scanner will transmit <Left ALT Make> “A” <Left ALT Break>

M-12

Download from Www.Somanuals.com. All Manuals Search And Download.

M-13

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Section N

Miscellaneous Features

Custom Defaults

N-1

N-3

Serial Program Mode

_{Download from Www.Somanuals.com. All Manuals Search A}N_{nd Download.}

N-1

MetroSelect^™

Custom Defaults

Metrologic manufatures several scanners for OEM applications. These scanners may use a different

set of defaults than Metrologic factory defaults. Scanning the bar code will reset the default table to

Metrologic defaults.

Enable Factory Defaults

846600

Scan this code followed by “Recall Defaults”

code to enable and load

Metrologic Factory Defaults.

Recall Defaults

999998

Download from Www.Somanuals.com. All Manuals Search And Download.

MetroSelect^™

Ruby Verifone Defaults

RCH

84661280

84660010

Scan this code followed by “Recall

Defaults” code to enable and load

Ruby Verifone Defaults.

Scan this code followed by “Recall

Defaults” code to enable and load

RCH Defaults.

Sanyo

Gilbarco

84660020

84660030

Scan this code followed by “Recall

Defaults” code to enable and load

Gilbarco Defaults.

Scan this code followed by “Recall

Defaults” code to enable and load

Sanyo Defaults.

ALT Defaults

84660040

Scan this code followed by “Recall

Defaults” code to enable and load

Alt Defaults.

_{Download from Www.Somanuals.com. All Manuals Search}N_A-_n2_{d Download.}

N-3

MetroSelect^™

Serial Program Mode

For Serial Program Mode, all commands must be framed by an STX (02 Hex) and ETX (03 Hex).

To recall defaults:

1) Transmit <STX>999999<ETX> through the Serial Port. This will put the scanner in serial

program mode. Scanning will be suspended and the scanner will respond with an ACK (06 Hex).

2) Transmit <STX>999998<ETX> through the Serial Port. This is the Recall Defaults bar code in the

MetroSelect guide. The scanner will respond with an ACK (06 Hex).

3) Transmit <STX>999999<ETX> through the Serial Port. This will cause the scanner to exit

program mode and save the new settings. The scanner will beep 3 times and send an

ACK (06 Hex).

If at anytime, the scanner cannot recognize a command, it will respond with a NAK (15 Hex).

Please refer to the Installation and User’s Guide of the scanner for a complete description of Serial

Program Mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

LG Electronics Car Video System L1720PQ User Manual
LG Electronics Washer 1 9 User Manual
Life Fitness Home Gym 64727 User Manual
Linear Telephone AE1000Plus User Manual
Mackie Universal Remote HDR24 96 User Manual
Marvel Industries Refrigerator 6SBARE User Manual
Maytag Washer MAV7600 User Manual
Memorex TV DVD Combo MVD2009CB User Manual
Mercedes Benz Automobile 2001 E 320 User Manual
Mesa Boogie Stereo Amplifier Mark IV Amplifier User Manual