Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Introduction........................................................................................................... 1
Scanner and Accessories................................................................................. 2
Scanner Components....................................................................................... 4
Maintenance..................................................................................................... 4
Caution and Serial Number Labels................................................................... 5
Cable Removal................................................................................................. 6
Cable Connection Warning............................................................................... 6
RS232, Light Pen or Laser Emulation .............................................................. 7
IBM 46xx or OCIA ............................................................................................ 8
Keyboard Wedge.............................................................................................. 9
Stand-Alone Keyboard ................................................................................... 10
Low Speed USB (-38)..................................................................................... 11
Full Speed (-40).............................................................................................. 11
Scanner Operation ............................................................................................. 12
How to Use CodeGate® and the Manual Activation Mode.............................. 12
Two Modes of Operation ................................................................................ 12
Indicators........................................................................................................ 13
Audible .................................................................................................... 13
Visual....................................................................................................... 14
Failure ..................................................................................................... 15
Depth of Field................................................................................................. 16
Configuration Modes ...................................................................................... 17
Troubleshooting Guide ....................................................................................... 20
RS232 Demonstration Program ......................................................................... 23
Design Specifications......................................................................................... 24
Applications and Protocols ................................................................................. 26
Default Settings.................................................................................................. 27
Upgrading the Flash ROM Firmware.................................................................. 32
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Scanner Pinout Connections.......................................................................... 33
Cable Connector Configurations .................................................................... 35
Safety............................................................................................................. 37
EMC ............................................................................................................... 38
Limited Warranty ................................................................................................ 40
Patents ............................................................................................................... 41
Index .................................................................................................................. 42
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
The MS5145 Eclipse™ is a single-line, hand-held laser scanner.
Equipped with Metrologic’s patented CodeGate® technology, Eclipse can be
used in a wide variety of applications. CodeGate technology allows the user to
easily target the desired bar code and complete the data transmission with a
simple press of a button. This combination makes Eclipse a perfect selection for
menu scanning, point-of-sale, document processing and inventory control.
With Metrologic’s state-of-the-art scanning technology embedded inside, the
MS5145 Eclipse has a longer working range and a wider scan field than a typical
CCD. The width of the scan line grows as the scanner moves further away from
bar codes. In addition, the laser beam pulses making lining up bar codes easy,
and when the scanner senses a bar code (CodeSense® Mode), the laser beam
automatically switches to scan mode and activates CodeGate to ensure high-
speed scanning and accuracy.
Metrologic has included many standard features such as: user configurable Flash
ROM, PowerLink user-replaceable cables, MetroSet®2 and MetroSelect®
configuration, and data editing (parsing).
ECLIPSE
MODEL NUMBER
INTERFACE
MS5145 – 00
MS5145 – 9
MS5145 – 11
MS5145 – 14
Laser Emulation
OCIA
IBM 468X/469X, RS232-TXD, RXD, RTS, CTS
RS232 - TXD, RXD, RTS, CTS, DTR, DSR
RS232 Low Speed USB,
Keyboard Emulation or Serial Emulation*
MS5145 – 38
MS5145 – 40
MS5145 – 41
MS5145 – 47
Full Speed USB
RS232/Light Pen Emulation
Keyboard Wedge, Stand Alone Keyboard and RS232
Transmit/Receive
*
Configurable for Keyboard Emulation Mode or Serial Emulation Mode. The default
setting is Keyboard Emulation Mode.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Scanner and Accessories
BASIC KIT
Description
Part #
MS5145
Eclipse Scanner
00-02544x
70-79016x
MetroSelect Single-Line Configuration Guide*
MS5100 Eclipse Series Installation and User’s Guide*
OPTIONAL ACCESSORIES
Description
Part #
AC to DC Power Transformer- Regulated 5.2VDC @ 1A output.
46-00525
90VAC to 255VAC, United States, Canada and Japan
90VAC to 255VAC, Continental European
90VAC to 255VAC, United Kingdom
90VAC to 255VAC, Australia
46-00526
46-00527
46-00528
46-00529
46-00530
90VAC to 255VAC, China
90VAC to 255VAC, India
Other items may be ordered for the specific protocol being used. To order additional items,
contact the dealer, distributor or call Metrologic’s Customer Service Department at
1-800-ID-METRO or 1-800-436-3876.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Scanner and Accessories
OPTIONAL ACCESSORIES
Part #
Description
RS232 PowerLink Cable with Built in Power Jack
2.1 m (7 ft.) straight cord, long strain relief, black
55-55000x-3
Keyboard Wedge PowerLink Cable with Adapter
2.1 m (7 ft.) straight cord, long strain relief, black
55-55002x-3
55-55020x-3
55-55235x -N-3
Stand Alone Keyboard PowerLink Cable,
2.1 m (7 ft.) straight cord, long strain relief, black
USB Low Speed Communication Cable, Type A
1.5 m (5 ft.) straight cord, long strain relief, black
USB Full Speed Cable, Locking Pus-Power™ Type A
3 m (10 ft.) straight cord, long strain relief, black
55-55200x -N-3
This cable is for use with full speed USB (-40)
interface only.
IBM and OCIA Applications,
Metrologic Voltage Converter Cable, ±12VDC to +5.2VDC
MVC**
** Contact a Metrologic customer service representative for additional
information on the MVC converter cable series and the host connections
available.
46-46633
Countertop Stand
Other items may be ordered for the specific protocol being used. To order additional items,
contact the dealer, distributor or call Metrologic’s Customer Service Department at
1-800-ID-METRO or 1-800-436-3876.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Scanner Components
ITEM NO.
DESCRIPTION
1
2
3
4
5
6
7
Mode Select Button/CodeGate Button (see page 12)
Red LED (see page 14)
Green LED (see page 14)
Red Output Window (Laser Aperture)
Speaker (see page 13)
10-Pin RJ45, Female Socket (see page 33)
Pin Hole for Cable Release (see page 6)
Figure 1. Scanner Components
Maintenance
Smudges and dirt can interfere with the proper scanning of a bar code.
The output window should be routinely cleaned with glass cleaner sprayed onto a
lint free, non-abrasive cleaning cloth.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Caution and Serial Number Labels
Figure 2. Label Location on the Bottom of the Scanner with Example
Caution
To maintain compliance with applicable standards, all circuits connected to the scanner must
meet the requirements for SELV (Safety Extra Low Voltage) according to EN/IEC 60950-1.
To maintain compliance with standard CSA C22.2 No. 60950-1/UL 60950-1 and norm
EN/IEC 60950-1, the power source should meet applicable performance requirements for a
limited power source.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Cable Removal
Disconnect the power supply from the PowerLink cable and turn off power to the
host system before removing the cable from the scanner.
1. Locate the small ‘pin-hole’ beneath
the Eclipse logo on the front side of
the scanner near the end of the
handle.
2. Bend an ordinary paperclip into the
shape shown.
3. Insert the paperclip (or other small
metallic pin) into the small ‘pin-hole’.
There will be a faint ‘click’ when the
connector’s lock releases.
4. Pull gently on the cable’s strain-relief
to remove the cable.
Figure 3.
Cable Connection Warning
Important: If the PowerLink cable is not fully latched the unit can power
intermittently.
Figure 4.
Figure 5.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
RS232, Light Pen or Laser Emulation
1. Turn off the host system.
2. Plug the male, 10-pin RJ45 end
of the PowerLink cable into the
10-pin socket on the MS5145.
3. Connect the 9-Pin female end of the
PowerLink cable to the appropriate
communication port on the host
device.
4. Plug the external power supply into the
power jack on the PowerLink cable.
Check the AC input requirements
of the power supply to make sure
the voltage matches the AC
outlet. The outlet must be
located near the equipment.
5. Connect AC power to the transformer.
6. Turn on the host system.
Figure 6. RS232, Light Pen, or Laser
Emulation Connections
Plugging the scanner into the serial port of the PC does not guarantee that
scanned information will appear at the PC. A software driver and correct
configuration settings are also required for proper communications to
occur.
Powering the MS5145 directly from the host device can sometimes cause
interference with the operation of the scanner or the computer. Not all
computers supply the same current. For this reason, Metrologic
recommends using an external power supply. For additional information
contact a Metrologic customer service representative.
All MS5145-00 scanners leave the factory with the Laser Emulation Mode
enabled. If you recall defaults while re-configuring the scanner the Laser
Emulation Mode will no longer be enabled. Refer to the MS5145-00 Laser
Emulation Mode section of the MetroSelect Single-Line Configuration
Guide for information on enabling the Laser Emulation Mode.
See page 5.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
IBM 46xx or OCIA
1. Turn off the host system.
2. Plug the male 10-pin RJ45 end of
the MVC cable into the 10-pin socket
on the MS5145.
3. For IBM:
connect the other end of the MVC
cable to Port 9 of the host device.
For OCIA:
Connect the other end of the MVC
cable to the appropriate
communication port on the host
device.
4. Turn on the host device
Figure 7. IBM (above) and OCIA
(below) Connections
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Keyboard Wedge
1. Turn off the host system.
2. Plug the male, 10-pin RJ45 end
of the PowerLink cable into the
10-pin socket on the MS5145.
3. Disconnect the keyboard from the
host/PC.
4. Connect the Y ends of the PowerLink
cable to the keyboard and the host’s
keyboard port. If necessary, use the
supplied adapter cable to make the
connections.
5. Plug the external power supply into the
power jack on the PowerLink cable.
Check the AC input
requirements of the power
supply to make sure the
voltage matches the AC
outlet. The outlet must be
located near the equipment.
Figure 8. Keyboard Wedge Connections
6. Connect AC power to the transformer.
7. Turn on the host system.
Powering the MS5145-47 directly from the computer can sometimes
cause interference with the operation of the scanner or the computer.
Not all computers supply the same current through the keyboard port,
explaining why a scanner may work on one computer and not another.
Contact a Metrologic Customer Service Representative if you require an
external power supply.
See page 5.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Stand-Alone Keyboard
1. Turn off the host system.
2. Connect the 10-pin RJ45 male
connector into the jack on the
Eclipse. You will hear a ‘click’ when
the connection is made.
If the scanner is receiving
power from the host system,
skip to step #5.
3. Connect the L-shaped plug of the
power supply into the power jack on
the PowerLink cable.
Make sure the AC input
requirements of the power
supply match the AC outlet.
Connect the power supply
into an AC outlet. The outlet
should be near the equipment
and easily accessible.
Figure 9. Stand-Alone Keyboard
Connection
4. Connect the PowerLink cable to the
keyboard port on the host system.
5. Turn on the host system.
Powering the MS5145-47 directly from the computer can sometimes
cause interference with the operation of the scanner or the computer.
Not all computers supply the same current through the keyboard port,
explaining why a scanner may work on one computer and not another.
Contact a Metrologic Customer Service Representative if you require an
external power supply.
See page 5.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
USB: Low Speed USB (-38)
Full Speed USB (-40)
1. Turn off the host system.
2. Connect the 10-pin RJ45 male
connector of the USB cable into the
jack on the Eclipse. You will hear a
‘click’ when the connection is made.
3. Connect the other end of the USB
cable to the host USB port.
4. Turn on the host system.
Figure 10. USB
As a default, the MS5145-38 leaves the factory with USB Keyboard
Emulation Mode enabled.
For information on configuring the MS5145-38 for USB Serial Emulation
Mode, please refer to the USB section of the MetroSelect Single-Line
Configuration Guide (00-02544X).
Plugging the scanner into a port on the host system does not guarantee
that scanned information will be communicated properly to the host
system. All Eclipse’s are shipped already configured with a set of
factory defaults. Please refer to the MetroSelect Single-Line
Configuration Guide or MetroSet2’s help files for instructions on
changing the scanner’s factory default configuration. The scanner and
host system must use the same communication protocols.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
How to Use CodeGate and the Manual Activation Mode
®
CODEGATE
MANUAL ACTIVATION MODE*
* This feature is not a default
setting. Refer to the MetroSelect
Configuration Guide for
instructions on enabling the
Manual Activation Mode.
Figure 11. CodeGate Enabled
Figure 12. Manual Activation Mode
Two Modes of Operation
CodeGate, Out-of-Stand
•
•
CodeGate activates when removed from the stand
Bar code data is transmitted when the button is pressed
Manual Activation Mode*, Out-of-Stand
•
•
Button activates laser
Bar code data is scanned and transmitted while button is held down
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Indicators
Audible
When the MS5145 scanner is operational, the scanner provides audible
feedback to indicate the status of the scanner and the last scan. Eight settings
are available for the tone of the beep (normal, 6 alternate tones and no tone).
for instructions on how to change the lone of the beeper, refer to the Single-Line
MetroSelect Configuration Guide.
One Beep – On Power Up
The green LED will turn on, then the red LED will flash and the scanner will
beep once. The red LED will remain on for the duration of the beep. The
scanner is now ready to scan.
One Beep – During Operation
When the scanner successfully reads a bar code, the red LED will flash and
the scanner will beep once (if programmed to do so). If the scanner does not
beep once and the red light does not flash, then the bar code has not been
successfully read.
Three Beeps – During Operation
When entering the configuration mode, the red LED will flash while the scanner
simultaneously beeps three times. The red LED will continue to flash until the
unit exits configuration mode. Upon exiting configuration mode, the scanner
will beep three times and the red LED will stop flashing.
When configured for communication timeout, 3 beeps during operation will
indicate that a communication timeout has occurred.
Three Beeps – On Power Up
This is a failure indicator. Refer to the Failure Modes section of this guide on
page 14.
Razzberry Tone
This is a failure indicator or an invalid code read during configuration mode.
Refer to the Failure Modes section of this guide on page 14.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Indicators
Visual
The MS5145 is equipped with a red LED and green LED that indicates the
scanner’s state and the status of the current scan when the unit is in operation.
Figure 13. LED Color and Location
Green and Red LEDs Are Off
The LEDs will not be illuminated if the scanner is not receiving power from the
host or transformer.
Steady Green
Indicates normal pulse or continuous laser operation. Accompanied by a
razzberry tone, it indicates that an invalid bar code has been scanned.
Flashing Green
After a period of inactivity, the ON time of the pulsing laser will be shortened.
During this time the green LED will flash. This indicates that the scanner is in
a power saver mode. When a bar code enters the laser field, the scanner will
wake up and return to normal pulse mode.
Steady Green and Single Red Flash
When the scanner successfully reads a bar code, the red LED will flash and
the scanner will beep. If the red LED does not flash and the scanner does not
beep, then the bar code has not been successfully read.
Steady Green and Steady Red
After a successful read, the scanner transmits the data to the host device.
Some communication modes require that the host inform the scanner when
data is ready to be received. If the host is not ready to accept the information,
the scanner’s red LED will remain on until the data can be transmitted.
Steady Green and Continuous Flashing Red
When entering the configuration mode, the red LED will flash, the green LED
will turn on and the scanner will beep three times. The red LED will continue to
flash and the green LED will stay on until the unit exits the configuration mode.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Indicators
Failure
One Razzberry Tone – On Power Up
This indicates the scanner has experienced a laser or flipper subsystem
failure. Return the unit for repair to a Metrologic Authorized Service Center.
Continuous Razzberry Tone with no LEDs
If, upon power up, the scanner emits a continuous razzberry tone, then the
scanner has an experienced an electronic failure. Return the unit for repair to
a Metrologic Authorized Service Center.
Three Beeps – On Power Up
If the scanner beeps 3 times on power up then, the non-volatile memory
(NovRAM) that holds the scanner configuration has failed. Return the unit for
repair to a Metrologic Authorized Service Center.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Depth of Field vs. Minimum Bar Code Element Width
Minimum Bar Code Element Width
A
B
C
D
E
F
mm
mils
.10
.12
.17
.26
.33
.66
4.1
4.8
6.8
10.4
13
26
Figure 14. Depth of Field vs. Minimum Bar Code Element Width
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
Configuration Modes
The MS5145 Eclipse has 3 modes of configuration.
•
Bar Codes
The Eclipse can be configured by scanning the bar codes located in the
MetroSelect® Single-Line Configuration Guide (MLPN 00-02544). This
•
MetroSet®2
This user-friendly Windows-based configuration software allows you to
simply ‘point-and-click’ at the desired scanner options. This software can be
ordered by calling 1-800-ID-METRO.
•
Serial Configuration
This mode of configuration is ideal for OEM applications. This mode gives
the end-user the ability to send a series of commands using the serial port of
the host system. The commands are equivalent to the numerical values of
the bar codes located in the MetroSelect Single-Line Configuration Guide
(MLPN 00-02544).
How does Serial Configuration work?
1. Each command sent to the scanner is the ASCII representation of each
numeral in the configuration bar code. The entire numeric string is framed
with an ASCII [stx] and an ASCII [etx].
EXAMPLE #1:
Command for Disabling Codabar
Command = [stx]100104[etx]
String Sent to Scanner = 02h 31h 30h 30h 31h 30h 34h 03h
(All values are hexadecimal).
2. If the command sent to the scanner is valid, the scanner will respond with an
[ack].
3. If the command sent to the scanner in invalid, the scanner will respond with
a [nak].
Note: If this occurs, the end-user must start over at the very beginning of
the configuration sequence. Re-transmitting the invalid command
will not work, the user must start over.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
4. During configuration, the motor and laser turn off. YOU CANNOT SCAN A
BAR CODE WHILE IN SERIAL CONFIGURATION MODE.
5. There is a 20 second window between commands. If a 20 second timeout
occurs, the scanner will send a [nak] and you must start over.
6. To enter serial configuration mode, send the following command
[stx]999999[etx].
7. To exit serial configuration mode, send the following command
[stx]999999[etx], the scanner will respond with an [ack] followed by 3 beeps.
8. This mode uses the current Baud Rate, Parity, Stop Bits and Data Bits
settings that are configured in the scanner. The default settings of the
scanner are 9600, Space, 2, 7 respectively. If a command is sent to the
scanner to change any of these settings, the change will NOT take effect
until after serial configuration mode is exited.
EXAMPLE #2:
The following example will set the scanner to the factory default settings,
Disable Scanning of Code 128 bar codes, change the beeper tone, and add
a “G” as a configurable prefix.
HOST
ASCII
SCANNER
FEATURE
COMMAND
REPRESENTATION
RESPONSE
Enter Configuration Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
[ack] or 06h
Load Defaults
Disable Code 128
Alternate Tone 1
Configure. Prefix #1
Code Byte 0
[stx]999998[etx] 02h 39h 39h 39h 39h 39h 38h 03h
[stx]100113[etx] 02h 31h 30h 30h 31h 31h 33h 03h
[stx]318565[etx] 02h 33h 31h 38h 35h 36h 35h 03h
[stx]903500[etx] 02h 39h 30h 33h 35h 30h 30h 03h
[stx]0[etx]
[stx]7[etx]
[stx]1[etx]
02h 30h 03h
02h 37h 03h
02h 31h 03h
Code Byte 7
Code Byte 1
Exit Configuration Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h
The scanner will beep three times!
The commands sent to the scanner do not include the small superscripted
‘3’ that you see in front of each bar code string in the MetroSelect manual.
THE ‘3’ SHOULD NOT BE SENT. IT IS A CODE TYPE DESIGNATION
ONLY!
For commands requiring additional bar codes to be scanned (such as
prefixes, suffixes, timeouts, etc.), simply send the code bytes in the same
order that you would normally scan the bar codes.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER OPERATION
EXAMPLE #3:
The following example shows the events that occur when an invalid bar code
is sent. This sample will load the factory default settings and then set the
baud rate to 19200.
HOST
ASCII
SCANNER
FEATURE
COMMAND
REPRESENTATION
RESPONSE
Enter Configuration Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ack] or 06h
Load Defaults
[stx]99999:[etx] 02h 39h 39h 39h 39h 39h 3Ah 03h [nak] or 15h
Invalid command was sent, you must start over!
Enter Configuration Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ack] or 06h
Load Defaults
[stx]999998[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ack] or 06h
[stx]415870[etx] 02h 34h 31h 35h 38h 37h 30h 03h [ack] or 06h
[stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ack] or 06h
19200 Baud Rate
Exit Configuration Mode
The scanner will beep three times!
This example illustrates two important points.
First, if an invalid command is sent from the host, the scanner responds with
a [nak] and the end-user must start over from the beginning.
Second, if a command is sent to change the Baud Rate, the new baud rate
does not take effect until after the end-user exits configuration mode.
ABBREVIATED ASCII TABLE
Character
[STX]
Hex Value
02h
Decimal Value
2
[ETX]
03h
3
[ACK]
06h
6
[NAK]
15h
30h
31h
32h
33h
34h
35h
36h
21
48
49
50
51
52
53
54
55
56
57
0
1
2
3
4
5
6
7
8
9
37h
38h
39h
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
The following guide is for reference purposes only. Contact a Metrologic
representative at 1-800-ID-Metro or 1-800-436-3876 to preserve the limited
warranty terms.
Symptoms
Possible Causes
Solution
All Interfaces
Check the transformer, the outlet
and power strip. Make sure the
cable is plugged into the unit.
No power is being
supplied to the unit.
The unit has no
LEDs, beep or
laser.
No power is being
supplied to the unit
from host.
Some host systems cannot supply
enough current to power Eclipse.
A power supply may be needed.
At power up the
unit beeps 2 times There is a ROM
A flash ROM upgrade is required.
and alternately
failure.
flashes the LEDs.
At power up the
There is a non-
unit beeps 3 times. volatile RAM failure.
At power up there
There is a RAM or
is a continuous
ROM failure.
razz tone.
Contact a Metrologic service
representative.
At power up there
is a razz tone and
the green LED
flashes.
There is a VLD
failure.
At power up there
is a razz tone and
both LEDs flash.
There is a scanning
mechanism failure.
The unit scans,
communicates
and beeps twice.
The same symbol
timeout is set too
short.
Adjust the same symbol timeout
for a longer time.
The unit powers
up, but does not
beep.
The beeper may be
disabled or no tone Enable beeper and select a tone.
has been selected.
UPC/EAN, Code 39, interleaved 2
The unit is trying to
The unit powers
up, but does not
scan and/or beep.
of 5, Code 93, Code 128 and
scan a particular
Codabar are enabled by default.
symbology that is
Verify that the type of bar code
not enabled.
being read has been selected.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Symptoms Possible Causes
The bar code being
Solution
Verify that the bar code being
scanned falls into the configured
criteria.
The unit powers scanned does not
up, but does not satisfy the configured
scan and/or
beep.
criteria for character
length lock or
The scanner defaults to a
minimum length.
minimum of 3 character bar code.
The unit scans a
bar code, but
locks up after the
first scan and the
red LED stays
on.
The unit is configured If the unit is setup to support
to support some form
of host handshaking
but is not receiving
the signal.
ACK/NAK, RTS/CTS, XON/XOFF
or D/E, verify that the host cable
and host are supporting the
handshaking properly.
The unit scans,
but the data
transmitted to the host system’s
host is incorrect. requirements.
The unit’s data format Verify that the unit’s data format
does not match the
matches that required by the host.
Make sure that the unit is
connected to the proper host port.
The print quality of
the bar code is
suspect.
Check the print mode. The type of
printer could be the problem.
Change the print settings.
The aspect ratio of
the bar code is out of
tolerance.
i.e. Change to econo mode or
high speed.
The unit beeps
at some bar
codes but NOT
for others of the
same bar code
symbology.
The bar code may
have been printed
incorrectly.
Check if it is a check
digit/character/or border problem.
The unit is not
configured correctly
for the type of bar
code being scanned.
The minimum symbol
length setting does
not work with the bar
code.
Check if the correct minimum
symbol length is set.
The unit scans
the bar code but configuration is not
there is no data. correct.
The unit’s
Make sure the scanner is
configured for the appropriate
mode.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Symptoms
Possible Causes
Solution
Make sure that the proper PC type
AT, PS2 or XT is selected. Verify
the correct country code and data
format is selected. Adjust the
The unit scans
but the data is
not correct.
The unit’s
configuration is not
correct.
inter-character delay symptom.
Increase the interscan code delay
setting. Adjust whether the F0
break is transmitted.
It may be necessary to try this in
both settings.
The unit is
transmitting
each character
twice.
The unit’s
configuration is not
correct.
Enable the Caps Lock detect
feature of the scanner to detect
whether the PC is operating in
Caps Lock.
Alpha
characters show
as lower case.
The computer is in
Caps Lock mode.
Everything
These characters
works except for may not be supported Try operating the scanner in Alt
a couple of
characters.
by that country’s key
look up table.
mode.
Check to make sure that the baud
rate and parity of the scanner and
the port match and that the
configuration is looking for
“RS232” data.
The com port at the
host is not working or
not configured
The unit
powers-up OK
and scans OK
but does not
communicate
properly to the
host.
properly.
The cable is not
connected to the
proper com port.
Check to make sure that the unit
is connected to the correct com
port on the host device.
The host is
receiving data
but the data
does not look
correct.
The scanner and host
may not be
configured for the
same interface
parameters.
Check that the scanner and the
host are configured for the same
interface parameters.
Inter-character delay
needs to be added to
the transmitted
output.
Add some inter-character delay to
the transmitted output by using
the MetroSelect Single-Line
Configuration Guide.
Characters are
being dropped.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
RS232 DEMONSTRATION PROGRAM
If an RS232 scanner is not communicating with your IBM compatible PC, key in
the following BASIC program to test that the communication port and scanner are
working.
This program is for demonstration purposes only. It is only intended to prove that
cabling is correct, the COM port is working, and the scanner is working. If the bar
code data displays on the screen while using this program, it only demonstrates
that the hardware interface and scanner are working. At this point, investigate
whether the application software and the scanner configuration match.
If the application does not support RS232 scanners, a software wedge program
that will take RS232 data and place it into a keyboard buffer may be needed.
This program tells the PC to ignore RTS-CTS, Data Set Ready (DSR) and Data
Carrier Detect (DCD) signals. If the demonstration program works and yours still
does not, jumper RTS to CTS and Data Terminal Reading (DTR) to DCD and
DSR on the back of your PC.
10
CLS
20
ON ERROR GOTO 100
30
35
40
50
OPEN “COM1:9600,S,7,1,CSO,DSO,CD0,LF” AS#1
PRINT “SCAN A FEW BAR CODES”
LINE INPUT #1, BARCODE$
PRINT BARCODE$
60
70
K$ = INKEY$: IF K$ = CHR$(27) THEN GOTO 32766
GOTO 40
100
110
PRINT “ERROR NO.”; ERR ;“PRESS ANY KEY TO TERMINATE.”
KK$ = INKEY$: IF K$ = “”THEN GOTO 110
32766 CLOSE: SYSTEM
32767 END
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN SPECIFICATIONS
MS5145 Eclipse
OPERATIONAL
Light Source: Visible Laser Diode (VLD) @ 650 nm
Laser Power: Less than 1.0 mW average
Depth of Scan Field: 0 mm – 140 mm (0" – 5.5") 0.33 mm (13 mil) Bar Code
Scan Speed: 72 ± 2 scan lines per second
Scan Pattern: Single scan line
Minimum Bar Width: 0.089 mm (3.5 mil)
Autodiscriminates all standard bar codes. For other
Decode Capability:
code types, call a Metrologic service representative.
RS232, Keyboard Wedge, USB, Light Pen Emulation,
System Interfaces:
IBM 468X/469X, OCIA, Stand Alone Keyboard
Print Contrast: 35% minimum reflectance difference
Up to 80 data characters. The maximum number will
No. Characters Read:
vary based on symbology and density.
Roll, Pitch, Yaw: 38°, 67°, 52°
Beeper Operation: 7 tones or no beep
Red = good read
Indicators (LED):
Green = laser on, ready to scan
MECHANICAL
Length: 170 mm (6.7")
Head: 63 mm (2.5")
Width
Handle: 39 mm (1.5")
Head: 35 mm (1.4")
Height
Handle: 31 mm (1.2")
Weight: 100.8 g (3.56 oz)
Specifications subject to change without notice.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN SPECIFICATIONS
MS5145 Eclipse
ELECTRICAL
Input Voltage: 5VDC ± 0.25V
Power: Operating
Current: Operating
675 mW
125 mA average @ 5VDC
DC Transformers: Class II; 5.2VDC @ 1A
For regulatory compliance information, see pages 37 – 39.
ENVIRONMENTAL
Operating
Storage
0°C to 40°C (32°F to 104°F)
-40°C to 60°C (-40°F to 140°F)
Temperature:
Humidity: 5% to 95% relative humidity, non-condensing
Light Levels: Up to 4842 Lux (450 footcandles)
Shock: Designed to withstand 1.5 m (5 ft.) drops
Contaminants: Sealed to resist airborne particulate contaminants
Ventilation: None required
Specifications subject to change without notice.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATIONS AND PROTOCOLS
The model number on each scanner includes the scanner number and factory
default communications protocol.
Scanner
Version Identifier
Communication Protocol(s)
Laser Emulation
00
9
OCIA
11
38
40
41
47
IBM 468X/469X, RS232 - TXD, RXD, RTS, CTS
Low Speed USB,
Serial Emulation or Keyboard Emulation
MS5145
Full Speed USB
RS232/Light Pen Emulation
Keyboard Wedge,
48
Keyboard Wedge, Stand-Alone Keyboard
The MS5145 Keyboard Wedge Series (-47) is designed for keyboard emulation
only. Many RS232 configurable functions available in other Metrologic scanners
are also available as keyboard wedge functions.
The following are the most important selectable options specific to keyboard
wedge:
Keyboard Type
•
•
**AT (includes IBM® PS2 models 50, 55, 60, 80)
IBM PS2 (includes models 30, 70, 8556)
Keyboard Country Type
•
•
•
**USA
Belgium
French
•
•
•
German
Italian
Japanese
•
•
•
Spanish
Swiss
United Kingdom
** Indicates a default setting (see pages 27 - 29 for additional information).
Refer to the MetroSelect Single-Line Configuration Guide (MLPN 00-02544) or
MetroSet2’s help files for information on how to change the default settings.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS
Many functions of the scanner can be configured or enabled/disabled.
The scanner is shipped from the factory configured to a set of default conditions.
All default parameters of the scanner have an asterisk ( * ) marked in the default
column. If an asterisk is not in the default column then the default setting is off or
disabled. Every interface does not support every parameter. A check
mark ( ) will appear in the interface column if the interface supports the
ꢀ
parameter listed.
Light IBM
Pen 46xx
Laser
Emulation
Parameter
Default OCIA RS232
KBW USB
Normal Scan Mode
Continuous Scan Mode
Blinky Scan
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Continuous Blinky Scan
Custom (One Shot) Scan
Manual Activation Mode
CodeGate Active
CodeGate Inactive
UPC/EAN
Code 128
Code 93
Codabar
Interleaved 2 of 5 (ITF)
MOD 10 Check on ITF
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Code 11
Code 39
Full ASCII Code 39
Mod 43 Check on Code 39
MSI-Plessy 10/10
Check Digit
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
MSI-Plessy Mod 10
Check Digit
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Paraf Support ITF
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS
Light IBM
Pen 46xx
Laser
Emulation
Parameter
Default OCIA RS232
Variable
KBW USB
ITF Symbol Lengths
Minimum Symbol Length
Symbol Length Lock
Bars High as Code 39
Spaces High as Code 39
Bars High as Scanned
Spaces High as Scanned
DTS/SIEMENS
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
3
None
*
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
DTS/NIXDORF
* ꢀ
NCR F
ꢀ
ꢀ
NCR S
Poll Light Pen Source
Beeper Tone
ꢀ
ꢀ
Normal
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Before
transmit
Beep/Transmit Sequence
Communication Timeout
Razzberry Tone on Timeout
Three Beeps on Timeout
None
Same Symbol Rescan
Timeout: 250 msecs
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Same Symbol Rescan
Timeout: 375 msecs
Same Symbol Rescan
Timeout: 500 msecs
Same Symbol Rescan
Timeout: 625 msecs
Same Symbol Rescan
Timeout: 750 msecs
Same Symbol Rescan
Timeout: 875 msecs
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Same Symbol Rescan
Timeout: 1000 msecs
No Same Symbol Timeout
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS
Light IBM
Pen 46xx
Laser
Emulation
Parameter
Default OCIA RS232
KBW USB
Infinite Same Symbol
Timeout
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Inter-Character Delay
Configurable In 1 msec steps 10 msecs
(max 255 msecs)
1 msecs
in KBW
Number Of Scan Buffers
(maximum)
4
Transmit UPC-A Check Digit
Transmit UPC-E Check Digit
Expand UPC-E
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Convert UPC-A to EAN-13
Transmit Lead Zero
On UPC-E
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Transmit UPC-A Number
System
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Transmit UPC-A
Manufacturer ID#
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Transmit UPC – A Item ID#
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Transmit Codabar Start/Stop
Characters
ꢀ ꢀ
ꢀ ꢀ
ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
CLSI Editing (Enable)
Transmit Mod 43 Check digit
on Code 39
Transit Mod 10/ITF
Transmit MSI-Plessy
Parity
ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ
Space
9600
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Baud Rate
8 Data Bits
7 Data Bits
*
Stop Bits
2
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS
Light IBM
Pen 46xx
Laser
Emulation
Parameter
Default OCIA RS232
KBW USB
Transmit Sanyo ID
Characters
ꢀ
ꢀ
Nixdorf ID
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
LRC Enabled
UPC Prefix
UPC Suffix
Carriage Return
*
*
ꢀ
ꢀ
Line Feed-Disabled by
Default in KBW
ꢀ
Tab Prefix
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Tab Suffix
“DE” Disable Command
“FL” Laser
Enable Command
DTR Handshaking support
RTS/CTS Handshaking
Character
*
Message RTS/CTS
XON/XOFF Handshaking
ACK/NAK
as
code
39
as
code
39
as
code
39
as
code 39
Two Digit Supplements
Five Digit Supplements
Bookland
ꢀ ꢀ
ꢀ ꢀ
ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ
as
code 39
as
code 39
977 (2 digit) Supplemental
Requirement
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Supplements are not
Required
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Two Digit Redundancy
Five digit Redundancy
* ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFAULT SETTINGS
Light IBM
Pen 46xx
Laser
Emulation
Parameter
Default OCIA RS232
KBW USB
100 msec to Find Supplement
Configurable in 100 msec
steps (max 800 msec)
*
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
as
code
39
as
code 39
Coupon Code 128
ꢀ ꢀ
ꢀ ꢀ ꢀ
† Configurable Code Lengths
7 avail
3 avail
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
† Code Selects with
Configurable Code Length
Locks
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
Configurable Prefix
Characters
10 avail
10 avail
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Suffix Characters
Prefixes for Individual
Code Types
Editing
ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ
Inter Scan-Code Delay
Configurable
(100 µsec steps)
800
µsec
Function/Control Key Support
Minimum Element Width
Configurable in 5.6 µsec
Steps
1 msec
ꢀ
ꢀ
† These options are mutually exclusive. One can not be used in conjunction with the other.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
UPGRADING THE FLASH ROM FIRMWARE
The MetroSet2 program is a functional component of Metrologic’s line of Flash-
based scanners. This program allows the user of a Metrologic scanner to quickly
upgrade to a new or custom version of software. It requires the use of a personal
computer running under Windows 95 or greater and the use of a communication
port. The user merely connects the scanner to a communications port of the PC,
launches the MetroSet2 program, and blasts off to new software upgrades.
Each MS5145, regardless of the version number or communication protocol,
can be upgraded. In other words, all RS232 (-41), keyboard wedge (-47), light
pen (-41), laser emulation (-00), OCIA (-9), IBM 468X/469X (-11), low speed USB
(-38), and integrated full speed USB (-40) units can be upgraded. To upgrade all
units, a power supply cable (MLPN 54-54014) is required. For RS232 units the
54-54000-3 PowerLink cable may be used in place of the 54-54014 PowerLink
cable.
The upgrades and custom software versions will be supplied by Metrologic in
files called Motorola S-record files. These files contain all the information needed
to upgrade the scanner. Simply add this file to the working directory or retrieve
from its current location.
The configuration guides the user with its simplistic one click approach. The user
must first select the file; once selected and verified the file is ready to be used in
the upgrade. Press the button to upgrade the scanner, the unit will go into a
“flash mode” – both the green and red LEDs will be on. The user can follow the
progress of the upgrade by watching the screen for details. When the upgrade is
complete, the scanner will respond with its normal one beep on power up. If two
beeps occur, the scanner did not upgrade properly. Contact a Metrologic service
representative for additional assistance.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER AND CABLE TERMINATIONS
Scanner Pinout Connections
The MS5145 scanner interfaces terminate to a 10-pin modular jack.
The serial # label indicates the interface enabled when the scanner is shipped
from the factory.
Figure 15.
MS5145-41 RS232C and
Light Pen Emulation
Pin
Function
1
2
3
Ground
RS232 Transmit Output
RS232 Receive Input
RTS Output
4
5
CTS Input
6
7
DTR Input/LTPN Source
Reserved
8
LTPN Data
9
+5VDC
10
Shield Ground
MS5145-47 Keyboard Wedge
and Stand-Alone Keyboard
MS5145-11 IBM 468X/469X
Pin Function
Pin
Function
1
2
3
Ground
1
2
3
Ground
RS232 Transmit Output
RS232 Receive Input
PC Data
RS232 Transmit Output
RS232 Receive Input
RTS Output
4
4
5
PC Clock
5
CTS Input
6
KB Clock
6
DTR Input
7
8
9
PC +5V
KB Data
+5VDC
7
8
9
IBM B-Transmit
IBM A+ Receive
+5VDC
10
Shield Ground
10
Shield Ground
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER AND CABLE TERMINATIONS
Figure 16.
MS5145-00 Laser Emulation
Pin
Function
1
2
3
Ground
RS232 Transmit Output
RS232 Receive Input
Flip Sense/Start of Scan
Output
Proximity Detect/
Trigger Emulation Output
Scan/Laser Enable Input
Reserved
4
5
6
7
8
Data Out
9
+5VDC
10
Shield Ground
MS5145 Full Speed (-40) and
Low Speed (-38) USB
MS5145-9 OCIA
Pin
1
2
3
4
5
6
7
Function
Pin
Function
Ground
1
2
3
4
5
6
7
Ground
N/C
N/C
N/C
N/C
RS232 Transmit Output
RS232 Receive Input
RDATA
RDATA Return
Clock In
D+
Clock Out
PC +5V/V_USB
Clock in Return/
Clock out Rtrn
+5VDC
8
8
D-
9
9
N/C
10
Shield Ground
10
Drain Wire
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER AND CABLE TERMINATIONS
Cable Connector Configurations
RS232 PowerLink Cable,
55-55000x-3
Pin
1
Function
Shield Ground
2
RS232 Transmit Output
RS232 Receive Input
3
4
DTR Input/Light Pen Source
Power/Signal Ground
5
Light Pen Data
(DSR Out for -14 interfaces)
6
9-Pin D-Type Connector
7
8
9
CTS Input
RTS Output
+5VDC
Stand Alone Keyboard
PowerLink Cable, 55-55020A-3
Pin Function
1
2
3
4
5
6
PC Data
NC
Power Ground
+5VDC PC Power to KB
PC Clock
6-Pin Male Mini-DIN Connector
NC
USB Communication
55-55235x-N-3 or 55-55200x-N-3
Pin Function
1
2
3
4
PC +5V/V_USB
D-
D+
Locking, Type A
MLPN 54-54213x-N-3 or
MLPN 54-54214x-N-3
Non-Locking, Type A
MLPN 54-54214x-N-3
Ground
Shield Shield
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SCANNER AND CABLE TERMINATIONS
Cable Connector Configuration
Keyboard Wedge PowerLink Cable
55-55002A-3
Pin Function
1
2
3
4
5
Keyboard Clock
Keyboard Data
No Connect
Power Ground
+5 Volts DC
5-Pin DIN, Female
Pin Function
1
2
3
PC Data
No Connect
Power Ground
4
5
6
+5 Volts DC
PC Clock
No Connect
6-Pin DIN, Male
Metrologic will supply an adapter cable with a 5-pin DIN male connector on one
end and a 6-pin mini DIN female connector on the other. According to the
termination required, connect the appropriate end of the adapter cable to the
PowerLink cable, leaving the necessary termination exposed for connecting to
the keyboard and the keyboard port on the PC.
Keyboard Wedge Adapter Cable
Pin Function
1
2
3
4
5
PC Clock
PC Data
No Connect
Power Ground
+5 Volts DC
5-Pin DIN, Male
Pin Function
1
2
3
Keyboard Data
No Connect
Power Ground
4
5
6
+5 Volts DC
Keyboard Clock
No Connect
6-pin Mini DIN, Female
36
Download from Www.Somanuals.com. All Manuals Search And Download.
REGULATORY COMPLIANCE
Safety
ITE Equipment
IEC 60950-1, EN 60950-1
Laser
Laser Class 1: IEC 60825-1:1993+A1+A2,
EN 60825-1:1994+A1+A2
Caution
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous laser light exposure. Under no circumstances should the
customer attempt to service the laser scanner. Never attempt to look at the laser beam, even
if the scanner appears to be nonfunctional. Never open the scanner in an attempt to look into
the device. Doing so could result in hazardous laser light exposure. The use of optical
instruments with the laser equipment will increase eye hazard.
Atención
La modificación de los procedimientos, o la utilización de controles o ajustes distintos de los
especificados aquí, pueden provocar una luz de láser peligrosa. Bajo ninguna circunstancia
el usuario deberá realizar el mantenimiento del láser del escáner. Ni intentar mirar al haz
del láser incluso cuando este no esté operativo. Tampoco deberá abrir el escáner para
examinar el aparato. El hacerlo puede conllevar una exposición peligrosa a la luz de láser.
El uso de instrumentos ópticos con el equipo láser puede incrementar el riesgo para la
vista.
Attention
L'emploi de commandes, réglages ou procédés autres que ceux décrits ici peut entraîner de
graves irradiations. Le client ne doit en aucun cas essayer d'entretenir lui-même le scanner
ou le laser. Ne regardez jamais directement le rayon laser, même si vous croyez que le
scanner est inactif. N'ouvrez jamais le scanner pour regarder dans l'appareil. Ce faisant,
vous vous exposez à une rayonnement laser qú êst hazardous. L'emploi d'appareils
optiques avec cet équipement laser augmente le risque d'endommagement de la vision.
Achtung
Die Verwendung anderer als der hier beschriebenen Steuerungen, Einstellungen oder
Verfahren kann eine gefährliche Laserstrahlung hervorrufen. Der Kunde sollte unter keinen
Umständen versuchen, den Laser-Scanner selbst zu warten. Sehen Sie niemals in den
Laserstrahl, selbst wenn Sie glauben, daß der Scanner nicht aktiv ist. Öffnen Sie niemals
den Scanner, um in das Gerät hineinzusehen. Wenn Sie dies tun, können Sie sich einer
gefährlichen Laserstrahlung aussetzen. Der Einsatz optischer Geräte mit dieser
Laserausrüstung erhöht das Risiko einer Sehschädigung.
Attenzione
L’utilizzo di sistemi di controllo, di regolazioni o di procedimenti diversi da quelli descritti nel
presente Manuale può provocare delle esposizioni a raggi laser rischiose. Il cliente non
deve assolutamente tentare di riparare egli stesso lo scanner laser. Non guardate mai il
raggio laser, anche se credete che lo scanner non sia attivo. Non aprite mai lo scanner per
guardare dentro l’apparecchio. Facendolo potete esporVi ad una esposizione laser
rischiosa. L’uso di apparecchi ottici, equipaggiati con raggi laser, aumenta il rischio di
danni alla vista..
37
Download from Www.Somanuals.com. All Manuals Search And Download.
REGULATORY COMPLIANCE
EMC
Emissions
FCC Part 15, ICES-003, CISPR 22, EN 55022
Immunity
CISPR 24, EN 55024
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Class A Devices
The following is applicable when the scanner cable is greater in length than 3 meters
(9.8 feet) when fully extended:
Les instructions ci-dessous s’appliquent aux cables de scanner dépassant 3 métres
(9.8 pieds) de long en extension maximale:
Folgendes trifft zu, wenn das Scannerkabel länger als 3 Meter ist:
This equipment has been tested and found to comply with limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the
interference at their own expense. Any unauthorized changes or modifications to this
equipment could void the user’s authority to operate this device.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Notice
This Class A digital apparatus complies with Canadian ICES-003.
Remarque
Cet appareil numérique de classe A est conforme à la norme canadienne NMB-003.
European Standard
Warning
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Funkstöreigenschaften nach EN55022:1998
Warnung!
Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich
Funkstörungen verursachen. In diesem Fall kann vom Betreiber verlangt werden,
angemessene Massnahmen durchzuführen.
Standard Europeo
Attenzione
Questo e’ un prodotto di classe A. Se usato in vicinanza di residenze private potrebbe
causare interferenze radio che potrebbero richiedere all’utilizzatore opportune misure.
Attention
Ce produit est de classe “A”. Dans un environnement domestique, ce produit peut être la
cause d’interférences radio. Dans ce cas l’utiliseteur peut être amené à predre les
mesures adéquates.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
REGULATORY COMPLIANCE
EMC
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Class B Devices
The following is applicable when the scanner cable is less than 3 meters
(9.8 feet) in length when fully extended:
Les instructions ci-dessous s’appliquent aux cables de scanner ne dépassant
pas 3 métres (9.8 pieds) de long en extension maximale:
Folgendes trifft zu, wenn das Scannerkabel kürzer als 3 Meter ist:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Notice
This Class B digital apparatus complies with Canadian ICES-003.
Remarque
Cet appareil numérique de classe B est conforme à la norme canadienne NMB-003.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
The MS5145 Eclipse™ scanners are manufactured by Metrologic at its Suzhou, China facility.
The MS5145 Eclipse scanners have a three (3) year limited warranty from the date of manufacture.
Metrologic warrants and represents that all MS5145 Eclipse scanners are free of all defects in material,
workmanship and design, and have been produced and labeled in compliance with all applicable U.S.
Federal, state and local laws, regulations and ordinances pertaining to their production and labeling.
This warranty is limited to repair, replacement of product or refund of product price at the sole discretion
of Metrologic. Faulty equipment must be returned to one of the following Metrologic repair facilities:
Blackwood, New Jersey, USA; Madrid, Spain; or Suzhou, China. To do this, contact the appropriate
Metrologic Customer Service/Repair Department to obtain a Returned Material Authorization (RMA)
number.
In the event that it is determined the equipment failure is covered under this warranty, Metrologic
shall, at its sole option, repair the Product or replace the Product with a functionally equivalent unit
and return such repaired or replaced Product without charge for service or return freight, whether
distributor, dealer/reseller, or retail consumer, or refund an amount equal to the original purchase
price.
This limited warranty does not extend to any Product which, in the sole judgment of Metrologic,
has been subjected to abuse, misuse, neglect, improper installation, or accident, nor any damage
due to use or misuse produced from integration of the Product into any mechanical, electrical or
computer system. The warranty is void if the case of Product is opened by anyone other than
Metrologic’s repair department or authorized repair centers.
THIS LIMITED WARRANTY, EXCEPT AS TO TITLE, IS IN LIEU OF ALL OTHER WARRANTIES
OR GUARANTEES, EITHER EXPRESS OR IMPLIED, AND SPECIFICALLY EXCLUDES,
WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE UNDER THE UNIFORM COMMERCIAL CODE, OR ARISING OUT OF
CUSTOM OR CONDUCT. THE RIGHTS AND REMEDIES PROVIDED HEREIN ARE
EXCLUSIVE AND IN LIEU OF ANY OTHER RIGHTS OR REMEDIES. IN NO EVENT SHALL
METROLOGIC BE LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES TO PERSON OR PROPERTY, OR EFFECT ON
BUSINESS OR PROPERTY, OR OTHER DAMAGES OR EXPENSES DUE DIRECTLY OR
INDIRECTLY TO THE PRODUCT, EXCEPT AS STATED IN THIS WARRANTY. IN NO EVENT
SHALL ANY LIABILITY OF METROLOGIC EXCEED THE ACTUAL AMOUNT PAID TO
METROLOGIC FOR THE PRODUCT. METROLOGIC RESERVES THE RIGHT TO MAKE ANY
CHANGES TO THE PRODUCT DESCRIBED HEREIN.
CORPORATE HEADQUARTERS,
NORTH AMERICA
METROLOGIC EUROPEAN REPAIR CENTER
(MERC)
Metrologic Instruments, Inc.
90 Coles Rd.
Blackwood, NJ 08012-4683
Customer Service Department
Tel: 1-800-ID-METRO
Fax: 856-228-6673
Metrologic Eria Ibérica, SL
C/Alfonso Gomez, 38-40, 1D
28037 Madrid
Tel: +34 913 751 249
Fax: +34 913 270 437
Email: [email protected]
MTLG AUTO ID INSTRUMENTS (SHANGHAI) CO., LTD
Suzhou Sales Office
BLK A, Room# 03/03-04
No.5 Xinghan Street, Xinsu Industrial Square
China-Singapore Suahou Industrial Park, Suzhou, PRC
Tel: 86-512-67622550
Fax: 86-512-67622560
Email: [email protected]
40
Download from Www.Somanuals.com. All Manuals Search And Download.
PATENTS
This METROLOGIC product may be covered by, but is not limited to, one or
more of the following U.S. Patents:
U.S. Patent No.;
5,216,232; 5,260,553; 5,340,971; 5,424,525; 5,484,992; 5,525,789; 5,528,024;
5,616,908; 5,627,359; 5,661,292; 5,777,315; 5,789,730; 5,789,731; 5,811,780;
5,828,048; 5,925,870; 6,029,894; 6,209,789; 6,227,450; 6,283,375; 6,347,743;
6,607,133; 6,619,549; 6,874,689;
No license right or sublicense is granted, either expressly or by implication,
estoppel, or otherwise, under any METROLOGIC or third party intellectual
property rights (whether or not such third party rights are licensed to
METROLOGIC), including any third party patent listed above, except for an
implied license only for the normal intended use of the specific equipment,
circuits, and devices represented by or contained in the METROLOGIC products
that are physically transferred to the user, and only to the extent of
METROLOGIC’S license rights and subject to any conditions, covenants and
restrictions therein.
Other worldwide patents pending.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
I
A
IBM .............................see interface
immunity...................................... 38
indicator ...................................... 24
audible..................... 4, 13, 20–21
failure........................... 15, 20–21
visual ................. 4, 14, 20–21, 32
interface ...................................... 24
IBM.......... 1, 8, 26, 27–31, 32, 33
Keyboard Wedge........ 1, 3, 9, 26,
27–31, 32, 33, 36
Laser Emulation ...... 7, 27–31, 34
Light Pen . 1, 7, 26, 27–31, 32, 33
OCIA ....... 1, 8, 26, 27–31, 32, 34
RS232 ............ 1, 2, 7, 26, 27–31,
32, 33, 35
AC .................................. see power
accessories ...............................2, 3
aperture.........................................4
B
beeper .........................see indicator
button ......................................4, 12
C
cable....................20–21, 36, 33–36
communication..2, 3, 6, 7–11, 22,
27, 32
MVC...........................................3
PowerLink...........6, 7–11, 32, 36,
33–36
Stand-Alone Keyboard ... 1, 3, 10,
26, 32, 33, 35
USB .........................................11
caution.........................................37
compliance.........................37–39
SELV..................................37–39
class ............................................39
CodeGate................................4, 12
compliance ........................5, 37, 38
configuration..26, 27–31, 36, 33–36
customer service .....................3, 40
USB................ 1, 2, 3, 26, 27–31,
32, 34, 35
K
Keyboard Wedge ........see interface
L
label .............................................. 5
laser.............................. 4, 5, 24, 37
LED.............................see indicator
Light Pen.....................see interface
D
DC.................................. see power
default..............7, 18, 19, 26, 27–31
depth of field................................16
M
manual .......................................... 2
modes ................................... 12, 17
E
EMC ............................................38
EMI..............................................38
emissions ....................................38
N
notices ........................................ 39
F
O
flash.........................................1, 32
OCIA...........................see interface
operation..................................... 39
G
green...........................see indicator
42
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
P
T
parameter..............................27–31
power.........................2, 3, 7, 24, 32
PowerLink........................ see cable
terminations .......................... 33–36
tone................................... 1, 13, 32
transformer......................see power
troubleshooting ..................... 20–21
R
U
razzberry tone .............................28
red...............................see indicator
RMA ............................................40
RS232 ........................ see interface
USB ............................see interface
V
VLD............................................. 24
S
safety.....................................37, 39
stand .............................................3
Stand-Alone Keyboard ............. see
interface
W
warranty...................................... 40
window.......................................... 4
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
April 2007
Printed in China
7 0 - 7 9 0 1 6 C
Download from Www.Somanuals.com. All Manuals Search And Download.
|