INSTALLATION INSTRUCTIONS FOR PART 99-7426
APPLICATIONS
Nissan Murano 2009-10
(Without Bose Audio)
(Climate Controls must be above OE radio)
99-7426
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted Charcoal To Match OEM Finish
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
E) Double DIN Trim Plate • F) Pocket
F
C
E
B
D
A
Harness & Antenna Connections (sold separately)
• 70-7552 - Nissan Harness 07-up
• 40-NI12 - Nissan Antenna Adapter 07-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver or Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7426 DASH DISASSEMBLY
NISSAN MURANO 2009-10
Disconnect the negative battery termi-
nal to prevent an accidental short cir-
cuit.
1
A
2
Unclip trim panel at bottom center of
dash. (Figure A)
Remove (1) Phillips screw from bot-
tom of each side trim panel. Unclip
and remove the side trim panels.
(Figure B)
3
4
Remove (3) Phillips screws securing
the climate control then unclip,
unplug and remove it from the sub
dash. (Figure C)
B
Continued on next page.
C
1
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7426 DASH DISASSEMBLY
NISSAN MURANO 2009-10
D
5
6
Remove (2) Phillips screws from the
panel below the radio (containing the
passenger air bag light) then unclip,
unplug and remove the panel.
(Figure D)
Remove (6) Phillips screws securing
the radio to the sub dash. Unplug and
remove radio. (Figure E)
Continue to kit assembly.
E
2
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7426 KIT ASSEMBLY
DIN MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Slide the DIN cage into the radio hous-
ing and secure by bending the metal
locking tabs down. (Figure A)
1
2
3
Slide the aftermarket radio into the
cage until it snaps into place. (Figure B)
Snap the pocket into the radio housing.
(Figure C)
Continue to final assembly.
B
C
3
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7426 KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure A)
1
2
3
Slide the radio into the radio housing
until it snaps into place. (Figure B)
Snap the Trim plate onto the front of
the Radio Housing. (Figure B)
4
Snap the pocket into the radio hous-
ing. (Figure C)
B
Continue to final assembly.
C
4
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7426 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Cut and remove the center bar from
the radio housing. (Figure A)
1
2
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
3
4
Slide the Double DIN or ISO mount
unit(s) into the bracket/radio housing
assembly and secure the unit(s) to the
assembly using the screws supplied
with the unit(s). (Figure C)
B
Snap the Double DIN trim plate onto
the front of the radio/housing.
(Figure C)
Continue to final assembly.
C
5
Download from Www.Somanuals.com. All Manuals Search And Download.
99-7426 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
Right Front (+) . . . . . . . . . . . . Gray
12V Ignition / Acc. . . . . . . . . . Red
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
1-800-221-0932
REV. 04/27/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7426
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|