INSTALLATION
&
PARTS AND SERVICE MANUAL
POP-2/4
POP-UP TOASTER
The POP-2/4 Pop-Up Toaster is designed to
allow the operator to toast a wide vaariety of
bread products. The wide mouth opening (1”)
will accommodate varioues thicknesses of
bread, from thin sliced to Texas toast.
Each of the two toasting slots can hold one or
two slices of bread and the self-centering toast
guides assure each slice, regardless of thick-
ness, will be perfectly toasted, time and time
again. All controls are located on the front
toaster panel.
The POP-2/4 is engineered for efficient, de-
pendable service throughout the years. Like
any piece of fine equipment with moving parts
and broad temperature ranges, physical wear
can take its toll. When this happens, the infor-
mation found in this manual will prove helpful.
Merco Savory, Inc.
1111 North Hadley Road
Fort Wayne, IN 46801
Phone: 800-547-2513
Fax: 260-436-0735
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Install the POP-2/4 in the most convenient location for ease of cleaning, maintenance, and general operation. Avoid
installing in locations with drafts, close proximity to grease or vapor-producing appliances, or other high ambient heat
equipment. Allow approximately 1” clearance on sides and back of unit for proper air circulation. Allow sufficient
overhead clearance for proper operation of this unit.
WARNING:
This toaster must be plugged into the proper voltage which is specified on the data plate located on the back
panel of the toaster. Use of any other voltage or altering of the plug or cord may damage the unit, will void the
warranty, and may cause injury.
ELECTRICAL SPECIFICATIONS
VOLTAGES
(VOLTS AC)
120
AMPERAGE MAX. POWER FREQUENCY
PHASE
CORD
(SUPPLIED)
PLUG
AMPS
14.8
9.1
(KW)
1.8
1.9
(HZ)
50/60
50/60
50/60
50/60
(SUPPLIED)
NEMA 5-15P
NEMA 6-15P
NEMA 6-15P*
NEMA 6-15P*
1
1
1
1
3'
3'
3'
3'
208
220
240
9.6
2.1
10.4
2.5
* NOTE:Non- U.S.A. models supplied without plug
The circuit on which the receptacle is installed must be of adequate wiring size and sufficient capacity to meet the
requirements indicated on the unit data plate and in conformance with the National Electrical Code and local electrical
installation codes. Failure to meet these requirenments will void the warranty.
SPECIFICATIONS (Standard Models)
MECHANICAL DIMENSIONS
WARRANTY
The POP-2/4 toaster is guaranteed to be free of defects in material and workmanship for a period of one (1) year from
date of purchase or 18 months from date of shipment from the factory, whichever comes first, provided that the equip-
ment is utilized to the manufacturer’s recommendations and instructions.
The POP-2/4 is warranted on an exchange basis only. Please contact our Service Department at 1-800-701-2992
for information.
A warranty registration card is provided with each toaster. Complete all equested information on this card and return to
Merco Savory, Inc. immediately to insure proper warranty registration. Damage resulting from accident, alterations,
misuse, abuse, improper installation or failure to follow use and care instructions will void the warranty.
**The warranty is applicable in the Continental U.S.A. and Hawaii only.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SEQUENCE OF OPERATIONS
On the POP2/4 toaster, the sequence of operations is separate but identical for both left and right toasting slots. Power
is permanently supplied to the power switch. Depressing the toast arm closes the power switch which supplies voltage
to the control board. The control board energizes an electro magnet which holds the toast arm in a down position. The
control board also supplies power to the heating elements. Adjusting the Light/Dark knob will change the amount of
time that the elements are energized and the toast arm is held in the down position. At the end of the cooking cycle,
the electro magnet and the heating elements and de-energized, along with the toast arm being returned to the up
position. Depressing the manual release button during the toast cycle de-energizes power to the control board and
returns the toaster to the starting position.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVAL, INSTALLATION AND ADJUSTMENTS
CAUTION:
UNPLUG UNIT AND ALLOW TO COOL BEFORE ATTEMPTING ANY SERVICE PROCEDURES IN THIS MANUAL
A. CASE COVER / CONTROL PANEL
1. Carefully place toaster upside down on a non-abrasive surface
2 Remove crumb tray.
3. Pry our rubber foot plugs adn use 1/3” nut driver to remove legs.
4. Push panel sides outward to gain clearance and slide out floor panel.
5. Push panel sides outward and lift out toaster chassis.
6. Unscrew both toast level handles and remove.
7. Remove one screw securing control panel to upper chassis.
8. Remove 2 screws securing control panel to lower chassis.
9. Gently pull control panel forward to gain access tothe inner workings.
Figure 1
B. RELEASE BUTTON
1. Remove case cover adn control panel. (Section A)
2. Remove bezel nut and star washer from release
button.
3. Push release button through panel and remove
push terminals #3 and #4 from p.c. board.
4. When re-attaching new push terminals to p.c.
board, polarity is not a factor. Refer to wiring diagram.
5. IMPORTANT: When installing new release button,
make sure both wires are positioned behind p.c.
board.
Figure 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
C. P.C. BOARD
1. Remove case cover and control panel. (Section A)
2. Remove knob from front of control panel. NOTE: Thecontrol knob on the front panel consists of two parts the knob
and the knob cap. The cap must be snapped off before removing the knob. Use a span ner wrench to loosen the knob
and pull off the shaft.
3. Remove wire connections from the p.c. board.
4. Remove the 4 mounting nuts and remove the p.c. board.
5. When installing the new p.c. board make sure the sensing probe is inserted through the opening in the p.c. board
reflector before securing front panel to th chassis. (Figure 3)
6. To replace the knob on the front panel, turn the adjustment shaft fully counterclockwise. Slip on th knob making
surethe white indicator mark on the knob is alligned with the lowest setting mark (Lighter) on the control panel.Hold the
knob securely inposition and tighten with a spanner wrench.Snap on the knob cap aligning the indicator marks on the
knob and cap. (Figure 4)
POWER SWITCH
1. Remove the case cover and control panel. (Section A)
2. Remove wire connections from the p.c. board noting
the proper orientation, and remove the front control panel.
3. Remove the black bushing from the toast lever
mechanism.IMPORTANT: Mark the positioning of the
bushing before removing.
4. Remove the 2 mounting screws and nuts from the switch.
5. Remove wire connections from the switch noting proper
orientation. Refer to the wiring diagram
6. For units with slots in the mounting brackets, make
sure the switch is fully forward in both slots.
E. TOAST LEVER SPRING
1. Remove case cover. (Section A)
Figure 3
2. Remove wire connections from power switch.
3. Remove the groundingnut from the floor of the toaster.
4. Open cable holding clamps with pliers.
5. Remove the strain relief clamp securing the power cord.
6. Pull the power cord out through the busing on the back panel.
F. POWER CORD
1. Remove case cover. (Section A)
2. Unhook the spring from both ends.
3. Insert the new spring, hooking the bottom end first.
Bring the top end of the spring through the small hole
in the chassis cover and hook into th elarger hole
4. Check for proper jumper wire positioning.
Figure 4
G. OUTER HEATER CARD ASSEMBLY
1. Remove case cover. (Section A)
2. With pliers, straighten corresponding twist tabs on underside of toaster.
3. On underside of toaster, remove corresponding sheet metal screw securing the end panel to the base.
4. Slide rear exterior panel down the power cord, away from the toaster.
5. When replacing left side heater card, remove strain relief bracket securing power cord to the inside panel.
6. Unhook the two toast level springs from the chassis top.
7. Straighten the 9 twist tabs on the chassis top.
8. With retaining ring pliers, remove the upper retaining rings from both guide shafts.
9. Remove upper chassis top.
10. Remove upper and lower terminal connections from the outer heater card.
NOTE: When replacing left side heater, remove tap wire.
11. Straighten twist tab securing the heater card assembly to teh inner front end panel.
12. On the inner rear end panel, straighten the center and corresponding twist tabs.
13. Carefully pushing outward on both end panels, lift the heater card assembly upward.
14. WEhen installing new heater card aassembly, make sure all internal components are positioned correctly at both
ends of the toaster. (Figure 8)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
(FOR MODELS MANUFACTURED BEFORE 9/1/90)
WHEN ATTACHING WIRE CONNECTIONS< MAKE SURE
CARGLAS SLEEVING IS FULLY INSERTED THROUGH
OPENINGS AND COMPLETELY COVER TERMINAL ENDS.
FAILURE TO DO SO WILL CAUSE ELECTRICAL SHORTING
G. Center Heater Card Assembly
1. Remove case cover. (Section A)
2. Remove 4 machine metal screws securing upper chassis.
3. Straghten twist tabs on upper chassis.
4. Disconnect both return springs at front of unit.
5. Remove both snap rings on upper chassis.
6. Slip off 2 heater jumper wires from chassis tabs.
7. Lift off upper chassis.
8. Lay unit on side. On underside of unit straighten center
row of twist tabs.
9. Remove 2 screws securing end panel to lower chassis.
(Figure 7)
10. Note: If thermal barriers are present on unit, remove
the 4 screws securing barrier to end panel. Do not remove
barriers. (Figure 5)
11. Straighten 3 twist tabs on end panel and the 1 tab on
center front panel. Pull off end panel.
12. Disconnect wiring connections to center heater card assem
13. Slide out center card assembly.
14. When replacing individual heater cards on center heater ca
assembly, be sure to note correct positioning of ceramic spacer
These spacers MUST be in correct position when new cards ar
attached.
15. NOTE: Left side heater card has tap wire. When installing t
card, be sure tap wire faces front of unit.
16. When replacing heater card assembly, be sure all spacer e
at ends of toast guides are in proper position.
Figure 7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5
Figure 6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|