Mellerware Scale 20502 User Manual

E X E C U T I V E  
M u n i c h G l a s s B a t h r o o m S c a l e  
SABS  
IEC60355  
Model:  
2 0 5 0 2  
3V Lithium  
PLEASE READ ALL INSTRUCTIONS BEFORE USE  
2 y e a r g u a r a n t e e  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Getting Accurate Readings:  
1. If the scale has not been used for a long time,  
proceed as follows:  
a) First, step lightly on the front corner (right or  
left) of the scale first to activate the scale.  
b) Second, wait for the scale to turn off. Then you  
may use the scale normally.  
Big LCD display  
Minimum capacity: 2.5kg  
Maximum Capacity: 150 kg  
Division: 100g (0.2 lb)  
Auto Zero-Auto off  
Low Battery / Overload Indication  
Power: 1 Lithium battery (CR2032)  
Equipped with High Precision Strain Gauge  
Sensor System (4 Sensors)  
2. If the scale is moved, proceed as follows:  
a) remove the battery from the scale for 5  
seconds  
b) replace the battery  
Preparations Before Use  
c) follow “Scale Setup” instruction (listed in  
Preparations Before Use point 2 above)  
3. Place scale on flat hard surface. Do not use  
scale on carpet because the reading will be  
inaccurate.  
1. Insert the Lithium battery (included). See figure  
1 (Note: Make sure battery is pushed all the  
way into its slot. Also make sure + side of  
battery is facing out)  
4. If the reading appears inaccurate, please  
check if the battery and the contact point are  
well connected. If scale has been in use for  
a long time, replace the battery and try again.  
If necessary, contact the local franchisers or  
contact our company.  
Handling Tips:  
1. Store the scale horizontally.  
2. Do not overload the scale.  
3. The scale is for home use only.  
4. Do not submerge scale in water. Use glass  
cleaner to clean glass platform of scale.  
5. Do not leave any objects on top of scale if the  
product is not to be used during a prolonged  
period of time. Also remove the battery to  
prevent it from being depleted or leaking.  
6. To avoid possible injury, do not stand on the  
edge of the platform.  
7. Place the scale in an area free from direct  
sunlight, heating equipment, high humidity, or  
extreme temperature change.  
8. To avoid slipping, make sure your feet and  
the glass platform of the scale are dry before  
standing on the scale.  
9. Please do not strike, hit or drop objects onto  
the glass platform, otherwise, the glass may  
break and cause serious injury.  
10.Strong magnetic fields may interfere with the  
operation of the scale. Avoid operating the  
scale in such areas.  
2. Scale Setup: Place the scale on a hard flat  
surface. Tap the front corner (right or left) of  
the scale with your foot. The digit “0” will scroll  
across the display. Then the display will show  
“0.0”This indicates that the scale has been  
setup correctly.  
a) Note: This “Scale Setup” procedure applies  
only after installing a battery. After completing  
“Scale Setup”, it does not need to be  
performed again unless battery is removed  
and replaced.  
b) Note: If you step on the platform before “0.0”  
appears, you will not obtain a reading. If this  
happens, step off the scale, then wait for  
display to turn off, follow above steps to setup  
scale.  
Scale Operation:  
To measure weight, simply stand with both feet  
in the center of the scale’s glass platform. Be  
sure to stand erect and remain still. After 3  
seconds the display will flash your weight and  
then display it steady.  
Usage Notes:  
1. When the display shows ”Err”, it means that  
the scale is overloaded.  
2. When the display shows ”Lo”, it means that  
the battery is low. Please replace the battery as  
soon as possible.  
Note: If a weight less than 10kg is placed on the  
scale, the scale will not activate. To weigh  
something less than 10kg, activate the scale first  
by tapping the front corner (right or left) of the  
scale with your foot.  
1. When no weight is on the scale for 10 seconds,  
the scale will turn off automatically.  
3. If scale display shows random digits or scale  
does not automatically shut off, proceed as  
follows:  
a. remove the battery for 10 seconds  
b. replace battery  
c. follow “Scale Setup” instruction (listed in  
Preparations Before Use point 2 above)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service Centre Share Call: 086 111 5006  
w e b : w w w. c r e a t i v e h o u s e w a r e s . c o . z a  
Download from Www.Somanuals.com. All Manuals Search And Download.  

LaCie Computer Drive d2 Quadra User Manual
La Crosse Technology Clock WS 8158U IT User Manual
Lennox International Inc Furnace G24M SERIES User Manual
Lenovo Server TS200V User Manual
LG Electronics Flat Panel Television 19LG3060 ZB37LG50 User Manual
Lincoln Electric Welding System SVM158 A User Manual
Loewe Flat Panel Television 9281 HD User Manual
Meade Weather Radio TE346W User Manual
Memorex Blu ray Player MVBD2535GPH User Manual
Microsoft Computer Accessories 2VG00202 User Manual