Promax
2000
Steam
Iron
complies with
INTERNATIONAL
Model:
2 3 5 0 0
IEC60355
2000W
SAFETY SPECIFICATIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USE
2 y e a r g u a r a n t e e
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
cools down so we recommend you start your
ironing with those garments that require lower
temperatures and then gradually increase the
setting.
5.Connect the appliance to the mains. The pilot
light will come on. Turn the temperature gauge
to the desired temperature.
When using electrical appliances, basic safety
precautions should always be followed,
including the following:
1.Read these instructions carefully before putting
the appliance into operation and keep them for
future consultation.
* Setting for nylon and acetate
** Setting for wool or silk
2.This appliance is only for domestic use, not
industrial use.
3.Do not leave the appliance within the reach of
children or disabled individuals.
*** Setting for cotton or linen
The pilot turns off when the desired temperature
is reached.
4.Before connecting the appliance to the
mains, check that the voltage indicated on the
nameplate coincides with the mains voltage.
5.No liability is accepted for damage caused
through inappropriate handling or use other
than that stipulated in this manual.
6.Do not use this appliance if it is damaged in any
way.
How to fill the water deposit
1.Unplug the appliance.
2.Fill the water deposit through the filling hole
(Fig. 1).
3.If your tap water is hard, use distilled water only.
4.Do not use chemically decalcified water.
5.The harder the water the more frequently the
iron should be cleaned.
7.Unravel the power cable fully.
8.Always unplug the iron when out of use, even
for a short period.
6.Throw out any excess water after use, once the
iron has been unplugged.
9.Unplug the iron before filling or emptying the
water deposit.
Steam Ironing
1.Fill up the iron as described in the section “How
to fill the water deposit”.
10.
Never submerge the iron in water or put
it under running water.
2.Plug in the iron.
3.Steam ironing is only possible if you select the
highest temperature***. Otherwise water may
seep through the base of the iron.
4.Wait for the pilot light to go off.
5.Turn the steam regulator to the desired position
6.During pauses and when the ironing is
complete, leave the iron standing upright.
7.Unplug the iron by pulling the plug out of the
socket. Pour out any leftover water and let the
iron cool down.
Before first use
• Some parts of the iron have been lightly
greased and thus the iron may produce a little
smoke when plugged in for the first time. This
will stop after a short period of time.
1.Before putting into use for the first time, remove
the plastic cover from the base and clean the
base with a soft cloth.
2. Keep the base smooth: do not touch metal
objects (buttons, zips, etc.)
Spray
1.The spray can be used when dry ironing or
when steam ironing.
Pure wool fabrics (100%) can be ironed with the
iron set to steam. Preferably choose a high
steam position and use a dry ironing cloth.
2.To do so, press the spray button. The spray
button has to be pressed repeatedly to release
the first spray.
Instructions for Use
Steam blast
The steam blast gives an extra steam jet to help
remove tough creases.
Temperature setting
1.Always check each garment’s ironing
instructions.
1.Select the maximum temperature*** on the
temperature gauge. Wait for the pilot light to go
off.
2.Press the steam blast button. Wait a few
seconds for the steam to penetrate into the
fabric before pressing again. For optimum
steam quality, do not apply more than three
successive blasts. The spray button has to be
2.If a garment does not have any ironing
instructions, see the fabric classification below.
3.If the garment has several different types of
fibre, select the lowest temperature setting.
4.Classify the number of garments by ironing
temperature. The iron heats up faster than it
Download from Www.Somanuals.com. All Manuals Search And Download.
pressed repeatedly to release the first spray.
thoroughly inspected and tested before
dispatch and is free from mechanical and
electrical defects. Should defects due to faulty
material or workmanship develop within two
years from date of purchase, under normal
domestic use, the appliance will be repaired
free of charge.
Cleaning and Maintenance
Cleaning
1.Unplug the appliance before proceeding to
clean.
2.Do not use solvents or abrasive products for
cleaning. A damp cloth with a few drops of
washing up liquid is enough.
Note: If this product is used commercially the
guarantee is limited to 90 days.
Kindly retain your purchase slip for this must be
presented if making a claim under the terms of
the guarantee. If such proof is not available the
product shall be deemed to be older than one
year and a charge for service and \ or spares
will be applicable. Should your appliance
require attention or appear not to be operating
properly, please take it to the retailer from whom
it was purchased, together with all parts and
your purchase slip.
This guarantee does not cover wear and tear or
damaged cause by over-loading negligence,
accidental or improper use. Any changes
will invalidate the guarantee, as would any
attempted repair.
“Self-cleaning”
1.It is important to self-clean the appliance at least
once a month to remove calcium and any other
built-up minerals inside the iron.
2.Place the steam regulator control in the No
steam position.
3.Fill up the deposit to the top.
4.Stand the iron upright and plug it in.
5.Turn the temperature gauge to the *** position.
6.Let the iron heat up until the pilot light turns off
and back on again.
7.Unplug the iron and place it over the sink.
8.Press the self-cleaning button.
9.Let the water flow out through the steam vents
in the base whilst lightly shaking the iron.
10.
Release the self-cleaning button after a
SERVICE
moment or when the deposit has been emptied
and place the iron in an upright position.
Before returning your product for service or repair
– check the following:
11.
Let the iron cool and then clean it.
• Your household mains supply socket is working
properly.
Maintenance
• The mains supply circuit is not overloaded.
• The instructions for use have been followed
carefully.
1.Any stains that may form on the base of the iron
can be cleaned off using a cloth dampened with
water and white vinegar.
If service becomes necessary within the
guarantee period the appliance should be
returned to the retail outlet where purchased
or carefully packed and marked “fragile-handle
with care“ and sent carriage paid to the address
below. (Postage is not refundable) Service
outside the guarantee period is still available but
this will be chargeable.
Problems and Solutions
Should the mains connection fail, do not try to
replace it since this is potentially dangerous.
Take the appliance to an authorized Technical
Support Service. The same applies to any other
type of problem.
This appliance complies with Low Voltage
Directive 73/23/ EC and with Electromagnetic
Compatibility Directive 89/336 EC.
SAVE THESE INTRUCTIONS
THIS PRODUCT IS FOR HOUSEHOLD USE
ONLY!
Warranty
We guarantee that this product has been
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Problem
Reason
Action
Pre-caution
Iron is leaking water.
Temperature is too low
Set the temperature to steam setting (cotton)
Check fabric type is suitable for high steam
temperature
Steam switch is on self clean
function
Turn steam switch setting to steam or 0
position
Switch steam setting to 0 (off) after use or
when filling tank.
Tank is overfilled
Empty water tank
Fill to MAX mark only.
Iron is in the horizontal position
too long.
When adjusting item place iron down in the
vertical position
If iron is left on the item in the horizontal
position for too long it may burn the fabric.
Check temperature setting is suitable for
fabric type.
Iron is not heating up
Temperature control dial is in
the off position
Turn the temperature control dial to the
desired temperature setting.
Switch on household socket
Check the socket with another appliance
Household socket is off.
Household socket is not
working
Ensure iron is in the upright position.
Appliance must be of similar wattage to
prevent overloading.
Iron is tripping mains
Overloaded circuit.
Unplug all appliances attached to the same
circuit and check iron.
Note that there can be up to 5 household
plug sockets on 1 circuit.
Iron sticking to clothing
Temperature is too hot
Turn down temparature on control dial.
Clean and rinse item.
Check temperature setting is suitable for
fabric type.
Clothing is dirty or not rinsed
thoroughly.
Use spray function to dampen item and
check temperture is correct.
Use a old linen cloth to remove any trace
of dirt on the soleplate. Use iron soleplate
cleaner for bad marks.
Creases not coming out
Not Enough Steam
Item is too dry or temperature
too low.
Use steam function.
Check temperature setting is suitable for
fabric type.
The steam control is off or set
too low.
Set the steam button/switch to on or full.
Ensure temperature control dial is set to the
3 dot position for steaming.
Check temperature setting is suitable for
fabric type.
The iron temperature is
too low.
Set temperature control dial to MAX or 3 dot
position for steaming.
The steam valve is blocked
due to water scale.
If your iron is fitted with a self clean function
carry out cleaning as per instructions.
Use distilled or demineralised water in your
iron to prevent blocking.
Download from Www.Somanuals.com. All Manuals Search And Download.
27 Nourse
Avenue Epping
2
Cape Town
P.O. Box 975 Eppindust 7475 South Africa
Tel: +27 21 534 8114 Fax: +27 21 534 8086
Service Centre Share Call: 086 111 5006
w e b : w w w. c r e a t i v e h o u s e w a r e s . c o . z a
Download from Www.Somanuals.com. All Manuals Search And Download.
|