Mellerware Coffeemaker 29002 User Manual

PALERMO 3-IN-1  
COFFEE BAR  
complies with  
INTERNATIONAL  
Model:  
2 9 0 0 2  
IEC60355  
1800W  
SAFETY SPECIFICATIONS  
PLEASE READ ALL INSTRUCTIONS BEFORE USE  
2 y e a r g u a r a n t e e  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX2290022__Palermo_IM.indd  
1
10/29/2008 12:05:29 PM  
Fig. 1  
Fig. 2  
Fig. 3  
Fig. 4  
Fig. 5  
Fig. 6  
Fig. 7  
Fig. 8  
Fig. 9  
Fig. 13  
Fig. 17  
Fig. 10  
Fig. 14  
Fig. 18  
Fig. 11  
Fig. 15  
Fig. 19  
Fig. 12  
Fig. 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX2290022__Palermo_IM.indd  
3
10/29/2008 12:05:31 PM  
PLEASE READ ALL THE INSTRUCTIONS BEFORE USING THIS PRODUCT  
IMPORTANT SAFEGUARDS  
hot when operated, so do not touch  
them with your hands directly.  
10. Do not immerse the coffee maker or  
power cord into water or any other  
liquids.  
11. Do not touch hot surfaces. Use  
handles or knobs.  
Before using the electrical appliance, the  
following basic precautions should  
always be followed.  
1. Before using the coffee maker for the 12. Do not use outdoors.  
first time check that the voltage of  
wall socket and mains corresponds  
to coffee maker’s rating label.  
2. Close supervision is necessary when  
your coffee maker is being used near  
children.  
3. Do not place the coffee maker on a  
hot surface or beside a fire, to avoid  
it being damaged.  
4. Remove the plug from the wall  
socket before cleaning and when not  
in use. Allow the coffee maker to cool  
down completely before removing/  
attaching components or before  
cleaning.  
5. Do not operate any appliance with  
a damaged cord or plug or after  
the appliance malfunctions, or is  
dropped or damaged in any manner.  
Return the coffee maker to the  
nearest authorized service facility for  
examination, repair or electrical or  
mechanical adjustment. Alternatively,  
contact us on our Customer Care  
Call Centre number (086 111 5006)  
for further assistance. Repairs made  
by any unauthorized person will null  
and void the 2 year guarantee.  
6. The use of an accessory which is  
not recommended by us may cause  
injury to persons or damage to the  
coffee maker.  
13. Do not place on or near a hot gas or  
electric burner, or in a heated oven.  
14. To disconnect, turn all controls to  
off then remove plug from the wall  
socket.  
15. Do not use the coffee maker for other  
than its intended use.  
16. Do not unscrew or remove the  
boiler cap while the machine is in  
operation. Wait until brewing cycle  
is completed and all the water and  
steam has been used up. (Pressure  
has been released)  
17. Use of the glass jugs  
The glass jug is designed for  
use with this coffee maker only.  
Do not place a hot glass jug on  
a wet or cold surface, it may  
crack/break.  
Do not use a glass jug if it is  
cracked or the handle is loose or  
weakened.  
Do not clean the glass jug with  
abrasive cleaning materials or  
steel wool.  
18. Save this instructions booklet for  
future reference.  
CAUTION:  
1. Never use warm or hot water to fill  
the coffee maker. Use cold water  
only!  
7. Place the coffee maker on flat  
surface or table. Do not hang its  
power cord over the edge of the  
table or counter top.  
8. Ensure that the power cord does not  
touch any hot surfaces.  
9. Some parts of the coffee maker are  
2. Never re-fill the coffee maker while it  
is in the on-position. Turn the coffee  
maker off and let it cool down for 10  
minutes before refilling.  
3. Before turning your coffee maker on,  
please make sure that the glass jug  
is flat on the inside of the circle on  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX2290022__Palermo_IM.indd  
4
10/29/2008 12:05:32 PM  
the heating plate.  
open the boiler unit cap or remove the  
filter holder while your coffee maker is  
turned “on”, or as long as there is  
pressure in the boiler unit.  
4. Keep your hands and the cord away  
from hot parts of the coffee maker  
during its operation.  
5. Never clean with scouring powders  
or hard implements.  
Please follow the instructions listed  
below to see if the machine is still under  
pressure. These safety precautions  
should be followed while your coffee  
maker is in use and 10 – 15 minutes after  
the last use of the machine.  
HOUSEHOLD USE ONLY  
KNOW YOUR COFFEE MAKER  
BEFORE THE FIRST USE  
1. Make sure the coffee maker is in the  
“off” position.  
We recommend that you get familiar with 2. Unplug the coffee maker from the  
all parts of your Coffee Maker before  
operating it, with the unit unplugged.  
Begin by inserting the metal filter into  
the filter holder (Fig.1), fit the filter into  
the brewing head, and remove and  
replace the boiler cap. Try the on/off  
buttons and steam controller, and check  
out all the parts of the coffee maker as  
well. Wash all loose parts in warm soapy  
water, rinse thoroughly and dry.  
wall socket.  
3. Hold a pitcher with cold water  
underneath the steam nozzle and  
insert the nozzle into the pitcher  
(Fig.4).  
4. Once the steam nozzle is immersed  
in the pitcher of water, turn the steam  
knob in an anti clockwise direction  
to open the steam nozzle. Continue  
this procedure until no more steam  
comes out of the steam nozzle.  
5. Turn the steam control knob to the  
clockwise direction to close the  
steam nozzle.  
To ensure the first cup of coffee tastes  
excellent, you should rinse the coffee  
maker with warm water as follows:  
6. Now you can remove the boiler unit  
cap and the filter holder.  
1. Add water into the tank (Fig.2)  
(for drip filter coffee) to the max  
capacity and operate the appliance  
per steps (1-5) of section “make drip  
filter coffee” (Do not use filter coffee  
powder for this first time use). Repeat  
it for several times to clean the  
appliance.  
2. Add fresh water into the boiler  
unit(Fig.3) (for espresso coffee)  
to the max capacity and operate  
the coffee maker per steps (1-9) of  
section “make espresso coffee” and  
section of “make cappuccino coffee”,  
but do not add coffee powder, repeat  
it several times.  
Incase there is still water in the boiler  
unit, remove the glass jugs and  
drip tray, then turn the coffee maker  
upside down to empty any remaining  
water in the boiler unit.  
MAKE DRIP FILTER COFFEE  
1. Open the tank cover (for drip filter  
coffee) and pour cold drinking water  
into water tank (Fig.2) according to  
the gauge. Respect the MAX level  
indicator. Purified drinking water  
provides a better taste and flavour of  
coffee.  
2. Place the permanent nylon filter into  
the funnel (Fig. 5) and make sure it is  
assembled correctly. If the funnel is  
not inserted correctly the tank cover  
can not be closed.  
CAUTION – PRESSURE  
It is important to remember to NEVER  
3. Add ground coffee into the  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX2290022__Palermo_IM.indd  
5
10/29/2008 12:05:32 PM  
permanent nylon filter with a  
measuring spoon (Fig. 6). Use  
one spoon (15g) of ground coffee  
powder per cup. You can adjust  
according to your taste.  
MAKE ESPRESSO COFFEE  
1. Turn the boiler unit cover in an anti-  
clockwise direction to open the boiler  
unit (see Figure A), then fill it with an  
adequate amount of drinking water.  
Purified drinking water provides a  
better taste and flavour of coffee.  
(Fig. 8 & 9)  
4. Close the tank cover. Place the large  
jug on the warming plate directly  
under the drip filter coffee section.  
(Fig. 7)  
5. Plug the power cord into the wall  
socket and press the switch to  
the “I” position, the switch will  
illuminate. The coffee maker will  
begin operating. You may stop the  
brewing by pressing the switch to the  
“O” position at any time. The coffee  
maker will continue brewing once  
pressing the switch to the “I” position  
again.  
Note: Always switch off the power and  
remove the plug from the wall  
socket before filling it with water.  
Ensure that the water does not  
overflow out of the boiler unit.  
2. Turn the boiler unit cover in a  
clockwise direction to tightly close  
it (see Figure A & 10), then turn the  
steam control knob in a clockwise  
direction to ensure that the steam  
control knob is tightly closed (see  
Figure B). If it is not closed, the boiler  
unit will not build up pressure and  
the water will flow out of the steam  
nozzle.  
Note: at any time, you can take out  
the large jug to serve, but the time  
should not exceed 20 seconds.  
Otherwise, the water will overflow  
out of the filter.  
6. The coffee will keep warm on the  
warming plate if you do not switch off  
the coffee maker. The coffee maker  
will automatically switch off after two  
hours, as a safety feature, so that it  
does not overheat.  
CLOSE  
OPEN  
Figure A  
STOP AND SERVE FUNCTION  
STEAM  
This automatically stops the flow of  
brewed coffee through the filter if the  
glass jug is removed from the warming  
plate during the brewing cycle. You  
have about 20 seconds between the  
removal of the glass jug and it being  
reinserted back onto the warming plate.  
Figure B  
The stop and serve closes off the filter  
so effectively that there is virtually no  
coffee dripping onto the warming plate.  
Once the glass jug is replaced, the  
brewing process and the flow of coffee  
into the glass jug can resume.  
STRONG  
Figure C  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX2290022__Palermo_IM.indd  
6
10/29/2008 12:05:32 PM  
3. Place the permanent filter into the  
filter holder(Fig. 1) and fill it with  
espresso coffee powder, according  
to your requirement by using the  
measuring spoon (marked with 2  
and 4 cups)(Fig. 11) and tap down  
the coffee powder. This compresses  
the coffee for stronger flavour. If there  
is any excessive coffee power on the  
top rim, scrape it off.  
control knob in an anti-clockwise  
direction. CAREFUL! Steam will  
escape from steam nozzle. Once  
the pressure is completely released  
and filter holder has cooled down,  
remove the filter holder by turning it  
anti-clockwise to the “  
“ (Fig. 15).  
Be sure to close the steam control  
knob by turning it in the clockwise  
direction until securely shut.  
4. Assemble the filter holder into the  
espresso side of the coffee maker by  
aligning the handle with the  
9. To clean the espresso filter turnover  
the filter lock, then press it with your  
thumb to secure the filter. Tilt the filter  
holder and tap it over the rubbish  
bin, then clear out the coffee residue  
(Fig. 16). Wash the filter holder and  
filter in fresh water and reassemble it  
correctly.  
“ mark. Move the handle once in  
position, so that it is aligned with the  
“LOCK” mark. Ensure that it is closed  
securely. (Fig. 12)  
5. To control the strength of the brew,  
turn the strength control knob to  
your desired position (“STRONG”,  
“LIGHT” or “STEAM” function) (see  
Figure C & 13), depending on your  
own taste or requirement.  
Note: return filter lock to original position  
before reattaching the filter holder.  
ATTENTION: HOT SURFACE  
The filter holder may be hot during  
Note: If the “STEAM” function is selected operation, to remove the filter holder,  
the water will not flow through the  
espresso section but rather convert  
the water to steam after a few  
minutes.  
turn the filter to the left, until the filter  
holder dislodges from the coffee maker.  
The metal parts might still be hot and  
can be cooled down by running cold  
6. Place the small jug on the removable water over it.  
drip tray and ensure the centre of  
the lid aligns with the spout of the  
filter holder (Fig. 14), then press the  
switch on the espresso side to the  
“I” position and the indicating light  
will be illuminated. Brewed espresso  
coffee will begin flowing into the  
small jug after approximately 3  
minutes.  
MAKE CAPPUCCINO COFFEE  
Cappuccino is made by adding fresh  
cream or frothed milk to the cup of  
espresso coffee.  
1. First prepare espresso coffee  
according to the steps (1-6) above  
and, ensure that the steam control  
knob has been turned off and turn  
the brew strength control knob  
to the “STEAM” position (Fig.C).  
After turning the switch on “I”,  
Note: to avoid any splashing, do not  
detach the filter holder while brewing  
coffee.  
7. Once the brewing has been  
completed, press the switch to the  
“O” position, remove the small jug  
from the drip tray and dispense  
coffee into cups. Now you can enjoy  
your homemade espresso coffee.  
8. Before removing the filter holder,  
always release the pressure in the  
boiler unit by carefully turning steam  
wait approximately 3 minutes  
for the coffee maker to generate  
enough steam to froth the milk.  
Before generating steam, fill a cup  
(preferably a straight walled cup)  
with about 150 ml of milk (preferably  
2% milk for the best results) for each  
cup of cappuccino. Lift up the cup to  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX2290022__Palermo_IM.indd  
7
10/29/2008 12:05:32 PM  
ensure the steam nozzle is immersed  
in the milk, and then carefully turn  
the steam control knob in an anti-  
clockwise direction for it to begin  
frothing milk (Fig. 17). When satisfied  
with the frothed milk then turn off  
the steam control knob to stop  
producing steam. If there is excess  
water in the boiler unit, more steam  
can be generated or espresso can  
be made.  
maker cool down completely before  
cleaning.  
2. Clean the housing of coffee maker  
by wiping it with a moist cloth or  
sponge. Do not use alcohol or  
abrasive cleaning agents as it might  
cause damage to the coffee maker.  
Note: Never immerse the housing in  
water for cleaning.  
3. Remove the filter holder, clean the  
coffee residue inside, and then  
you can clean it and the filter with  
dishwashing liquid. Be sure to rinse  
with clear water.  
Note 1: Bear in mind that the milk  
generally increases in volume by 1.5  
times, so make sure the height of the  
cup is enough.  
4. Clean the glass jugs, permanent filter,  
and drip tray (Fig. 19) in warm water  
with some dishwashing detergent.  
Note 2: to get a better effect, move the  
cup constantly up and down. This  
spreads the temperature throughout  
the milk faster.  
2. Mix espresso coffee with frothed milk  
and stir, add chocolate powder if  
necessary.  
HOW TO DESCALE MY COFFEE  
MAKER  
3. It is necessary to clean the steam  
nozzle once you have finished using  
the coffee maker, so that the dry  
milk doesn’t block the steam outlet.  
In order to do this, grasp the nozzle  
with your hand and secure the pipe  
with your other hand. Now pull the  
steam nozzle off (Fig. 18). Wash it  
with warm water to clean off any milk  
residue. After cleaning, reassemble it  
back into its original position.  
The coffee maker must be de-scaled  
regularly. The frequency depends on  
the hardness of your water and how  
often you use the coffee maker.  
Recognisable indications that de-scaling  
is necessary are:  
Increased noise during boiling  
Longer preparation time  
If usage is frequent, de-scaling should  
be carried out as follows:  
Caution: The steam nozzle will be hot  
after steaming, so we advise  
With soft water, once per year  
With medium water, once every  
3 months  
that you allow it to cool down  
before cleaning or touching it.  
With hard water, once per month  
If in doubt regarding the water  
hardness in your area, you may  
call your local water department.  
For ecological and health  
reasons, we recommend the  
exclusive use of biological  
materials such as citric acid,  
which can be obtained from  
pharmacies.  
Note: to prepare more than one  
cappuccino, first make all the coffees  
and then at the end prepare the  
frothed milk for all the cappuccinos.  
CLEANING AND MAINTENANCE:  
1. Unplug the coffee maker from  
the wall socket and let the coffee  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX2290022__Palermo_IM.indd  
8
10/29/2008 12:05:32 PM  
For the section of making drip filter  
coffee  
piping requires periodic cleaning.  
You should clean away the mineral  
deposits every 2-3 months.  
Note: the switch referring on the  
following section is the switch for drip  
filter coffee.  
2. Fill the boiler unit with water  
and descaler to the MAX level  
(Approximate 0.24L, the scale of  
water to descaler is 4:1). Please use  
“household descaler”. You can also  
use citric acid instead of descaler  
(the one hundred parts of water  
and three parts of citric acid). Tip:  
leave the solution in the boiler for 15  
minutes before brewing.  
3. Brew the water according to the  
program of making espresso coffee  
without coffee powder in the filter.  
4. Turn the brew strength control knob  
to “STRONG” or “LIGHT” position,  
then turn the switch on by pressing it  
to the “I” position and approximately  
3 min later the water will flow out.  
After making 2 espresso sized cups  
of hot water, turn off the switch by  
pressing it to the “O” position.  
5. Turn brew strength control knob  
to the “STEAM” position. Press  
the switch to the “I” position. Wait  
approximately 3 minutes to generate  
the steam and release the steam for  
approximately 2 minutes. Afterwards,  
turn off the switch by pressing it to  
the “O” position.  
1. Fill the tank with water and descaler  
to the MAX level (Approximate 1.25L,  
the scale of water to descaler is 4:1).  
Please use “household descaler”.  
You can also use citric acid instead  
of descaler (the one hundred parts of  
water and three parts of citric acid).  
Tip: leave the solution in the tank for  
15 minutes before brewing.  
Note: Descale without using coffee  
powder.  
2. Place the large jug onto warming  
plate and pay attention to let the  
centre of large jug to align with that  
of brewing basket.  
3. Pressing the switch to the “I”  
position, the indicator will be  
illuminated. After a while, water will  
drip out automatically.  
4. After the coffee maker has  
percolated the equivalent of one cup,  
press the switch to the “O” position  
to stop the water.  
5. Leave the solution to work for 15  
minutes, and then repeat the steps  
3-5 again.  
6. Turn the appliance on by pressing  
the switch to the “I” position and run  
off the water until the water tank is  
completely empty.  
7. Rinse by operating the coffee maker  
with clean water at least 3 times.  
6. Restart the unit and repeat steps 3-5  
at least 3 times, but be sure to re-fill  
with water.  
7. Then turn the brew strength control  
knob to the “STRONG” or “LIGHT”  
position, and brew until no descaler  
is left.  
8. Rinse the system by repeating steps  
3-5 with clean water. Repeat this  
3 times until no water is left in the  
boiler unit.  
For the section of making espresso  
coffee  
Note: the switch being referred to in the  
following section is the switch for the  
espresso coffee.  
9. Repeat step 8 at least 3 times to  
make sure steam pipe is clean.  
1. To make sure your coffee maker is  
operating efficiently, and producing  
the best flavour of coffee, the internal  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX2290022__Palermo_IM.indd  
9
10/29/2008 12:05:32 PM  
TROUBLE SHOOTING  
Symptom  
Cause  
Corrections  
Water leaking out of the  
Glass Jug  
The glass jug is not situated The glass jug is not situated  
properly properly  
The level of water in the tank The level of water in the tank  
exceeds the MAX indicator. exceeds the MAX indicator.  
Espresso coffee drops out  
too slowly (Not only for the  
coffee maker with pump)  
Ground coffee too ne  
Use 1# coffee powder.  
The metal parts in the tank  
have rust.  
The descaler is not of the  
recommended type. It may  
corrode the metal parts in  
the tank.  
Use the descaler recom-  
mended by Creative House-  
wares (PTY) LTD  
Water leaks from the bottom  
of coffee maker.  
There is too much water in  
the drip tray.  
Clean the edge of the lter  
Clean coffee maker per the  
content in the section “be-  
fore the rst use” for several  
times.  
The coffee maker was not  
rinsed correctly after clean-  
ing mineral deposits.  
Acid (vinegar) taste exists in  
Espresso coffee.  
The coffee maker was not  
rinsed correctly after clean-  
ing mineral deposits.  
Please use fresh coffee  
powder, or store unused  
coffee powder in a cool,  
dry place. After opening a  
package of coffee powder,  
reseal it tightly and store it in  
a refrigerator to maintain its  
freshness.  
The coffee maker does not  
work any more.  
The wall socket is not oper- Plug the power cord into an-  
ating well, or the plug is not other wall socket correctly, if  
plugged in properly.  
the appliance still does not  
work, please contact with  
the authorized service facil-  
ity or Creative Housewares  
for repairing.  
The steam cannot froth.  
The steam pipe may be  
blocked  
Use a pin to clear any resi-  
due from the pipe. Follow  
steps 5-6 under HOW TO  
DESCALE MY COFFEE  
MAKER (For the section of  
making espresso coffee). If  
the problem persists, please  
contact us.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX29002_Palermo_IM.indd 10  
10/29/2008 12:05:32 PM  
27 Nourse  
Avenue Epping  
2
Cape Town  
P.O. Box 975 Eppindust 7475 South Africa  
Tel: +27 21 534 8114 Fax: +27 21 534 8086  
Service Centre Share Call: 086 111 5006  
w e b : w w w. c r e a t i v e h o u s e w a r e s . c o . z a  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MW_EX29002_Palermo_IM.indd 12  
10/29/2008 12:05:32 PM  

Lanzar Car Audio Car Speaker MAXP104D User Manual
Learning Resources Games Brochure User Manual
Lennox International Inc Furnace G50UH 24A 045 User Manual
LG Electronics Microwave Oven LRMM1430SB User Manual
Lincoln Automobile 1999 Continental User Manual
LumiSource eBook Reader LSH FIREFLY FL User Manual
Makita Power Screwdriver 6842 User Manual
Maytag Range MER6755AAS26 User Manual
Mellerware Hot Beverage Maker 21205G User Manual
Midland Radio Two Way Radio G 225 User Manual