OPERATOR'S MANUAL
MODEL NO. MC13538LT
13.5 HP* 38 INCH
LAWN TRACTOR
•
Assembly
•
Operation
Customer Responsibilities
Service and Adjustments
Storage
Troubleshooting
•
•
•
•
*As rated by the engine manufacturer
532 43 25-84 Rev. 1
Printed in the U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
III. CHILDREN
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.
GENERAL SERVICE
•
Never operate machine in a closed area.
Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
•
•
•
•
•
Keepchildrenoutofthemowingareaandinthewatchful
care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the
area.
•
•
Never tamper with safety devices. Check their proper
operation regularly.
Keep machine free of grass, leaves, or other debris
build-up. Cleanoilorfuelspillageandremoveanyfuel-
soaked debris. Allow machine to cool before storing.
If you strike a foreign object, stop and inspect the
machine. Repair, if necessary, before restarting.
Nevermakeanyadjustmentsorrepairswiththeengine
running.
Check grass catcher components and the discharge
chute frequently and replace with manufacturer's rec-
ommended parts, when necessary.
Before and while backing, look behind and down for
small children.
•
•
•
Nevercarrychildren,evenwiththebladesshutoff. They
may fall off and be seriously injured or interfere with
safemachineoperation.Childrenwhohavebeengiven
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
Never allow children to operate the machine.
Useextracarewhenapproachingblindcorners,shrubs,
trees, or other objects that may block your view of a
child.
•
•
•
•
•
Mower blades are sharp. Wrap the blade or wear
gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service
as required.
Maintain or replace safety and instruction labels, as
necessary.
IV. TOWING
•
Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.
•
•
•
•
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed
equipment.
On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop.
•
Be sure the area is clear of bystanders before operat-
ing. Stop machine if anyone enters the area.
Never carry passengers.
•
•
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while back-
ing.
Nevercarrychildren,evenwiththebladesshutoff. They
may fall off and be seriously injured or interfere with
safemachineoperation.Childrenwhohavebeengiven
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
Keepchildrenoutofthemowingareaandinthewatchful
care of a responsible adult other than the operator.
Be alert and turn machine off if a child enters the
area.
Before and while backing, look behind and down for
small children.
Mow up and down slopes (15° Max), not across.
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
V. SERVICE
SAFE HANDLING OF GASOLINE
To avoid personal injury or property damage, use extreme
careinhandlinggasoline. Gasolineisextremelyflammable
and the vapors are explosive.
•
•
Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
Use only approved gasoline container.
Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling.
Never fuel the machine indoors.
Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as on a water
heater or other appliances.
Never fill containers inside a vehicle or on a truck or
trailer bed with plastic liner. Always place containers
on the ground away from your vehicle when filling.
Remove gas-powered equipment from the truck or
trailer and refuel it on the ground. If this is not possible,
then refuel such equipment with a portable container,
rather than from a gasoline dispenser nozzle.
Keepthenozzleincontactwiththerimofthefueltankor
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
If fuel is spilled on clothing, change clothing immedi-
ately.
Never overfill fuel tank. Replace gas cap and tighten
securely.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
•
•
•
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONGRATULATIONS on your purchase of a new tractor.
Ithasbeendesigned,engineeredandmanufacturedtogive
you the best possible dependability and performance.
PRODUCT SPECIFICATIONS
Gasoline Capacity
and Type:
1.50 Gallons
Unleaded Regular
Shouldyouexperienceanyproblemyoucannoteasilyrem-
edy,pleasecontactyournearestauthorizedservicecenter/
department. We have competent, well-trained technicians
and the proper tools to service or repair this tractor.
Oil Type (API-SG-SL):
Oil Capacity:
SAE 30 (above 32°F/0°C)
SAE 5W-30 (below 32°F/0°C)
48 oz.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the “SAFETY RULES”.
Spark Plug:
Champion RC12YC
(Gap: .030")
Ground Speed (MPH):
Forward:
1st
2nd
1.1
1.4
2.2
3.4
4.3
5.5
1.7
CUSTOMER RESPONSIBILITIES
•
•
Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your tractor.
3rd
4th
5th
6th
•
Follow the instructions under “Maintenance” and “Stor-
age” sections of this owner’s manual.
Reverse:
Charging System:
Battery:
3 Amps Battery
5 Amps Headlights
WARNING: This tractor is equipped with an internal com-
bustion engine and should not be used on or near any
unimprovedforest-covered,brush-coveredorgrass-covered
land unless the engine’s exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained
in effective working order by the operator.
AMP/HR:
Min. CCA:
U1R
28
230
Case Size:
Blade Torque:
45-55 FT. LBS.
A spark arrester for the muffler is available through your
nearest authorized service center/department.
TABLE OF CONTENTS
SAFETY RULES .........................................................2-3
PRODUCT SPECIFICATIONS....................................... 4
CUSTOMER RESPONSIBILITIES................................. 4
ASSEMBLY.................................................................6-7
OPERATION .............................................................8-13
MAINTENANCE SCHEDULE ...................................... 14
MAINTENANCE .....................................................14-17
SERVICE AND ADJUSTMENTS............................18-22
STORAGE.................................................................... 23
TROUBLESHOOTING............................................24-25
WARRANTY................................................................. 28
4
Download from Www.Somanuals.com. All Manuals Search And Download.
UNASSEMBLED PARTS
Steering Wheel
Steering
(1) Large Flat Washer
(1) 5/16 Lock Washer
Wheel Insert
(1) Hex Bolt
5/16-18 x 4
Steering
Extension
Shaft
Steering Wheel
Adapter
Steering
Boot
Seat
(1) Washer
(1) Knob
(1) Seat
(1) Oil Drain Tube
For Future Use
Slope Sheet
Keys
(2) Keys
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.
•
Place tabs of steering boot over tab slots in dash and
push down to secure.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
INSTALL STEERING WHEEL
•
•
•
•
•
•
Position front wheels of the tractor so they are pointing
straight forward.
Remove steering wheel adapter from steering wheel
and slide adapter onto steering shaft extension.
Position steering wheel so cross bars are horizontal
(left to right) and slide inside boot and onto adapter.
Assemble large flat washer, 5/16 lock washer, 5/16 hex
bolt and tighten securely.
Snap steering wheel insert into center of steering
wheel.
Remove protective materials from tractor hood and
grill.
(1) 5/16" wrench
(2) 7/16" wrenches
(2) 1/2" wrenches
(1) 9/16" wrench
Utility knife
Tire pressure gauge
Pliers
Whenrightorlefthandismentionedinthismanual,itmeans
when you are in the operating position (seated behind the
steering wheel).
TO REMOVE TRACTOR FROM
CARTON
UNPACK CARTON
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN
SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO
ROLL OFF SKID.
•
•
•
Remove all accessible loose parts and parts cartons
from carton.
Cut along dotted lines on all four panels of carton.
Remove end panels and lay side panels flat.
Check for any additional loose parts or cartons and
remove.
INSERT
BOLT
LOCK
WASHER
TO CHECK BATTERY (See Fig. 1)
LARGE FLAT
WASHER
•
Lift seat to raised position.
NOTE: If this battery is put into service after month and
year indicated on label (label is located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in Maintenance section of this manual
for charging instructions).
STEERING
WHEEL
STEERING
BOOT
•
For battery and battery cable installation see "RE-
PLACINGBATTERY"inthe"ServiceandAdjustments"
section in this manual.
ADAPTER
EXTENSION
LOWER
SHAFT
SHAFT
STEERING
SEAT
LABEL
02602
Fig. 1
Fig. 2
BEFORE REMOVING TRACTOR FROM
SKID
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment knob.
•
Remove adjustment knob and flat washer securing
seat to cardboard packing and set aside for assembly
of seat to tractor.
ATTACH STEERING WHEEL (See Fig. 2)
ASSEMBLE EXTENSION SHAFT AND BOOT
•
Slide extension shaft onto lower steering shaft.
•
Pivotseatupwardandremovefromthecardboardpack-
ing. Remove the cardboard packing and discard.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
•
•
Place seat on seat pan and assemble shoulder bolt.
CHECK DECK LEVELNESS
For best cutting results, mower housing should be prop-
erly leveled. See “TO LEVEL MOWER HOUSING” in the
Service and Adjustments section of this manual.
Tighten shoulder bolt securely.
Assemble adjustment knob and flat washer loosely.
Do not tighten.
•
•
Lower seat into operating position and sit on seat.
CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly.
Slideseat untilacomfortablepositionisreachedwhich
allows you to press clutch/brake pedal all the way
down.
Get off seat without moving its adjusted position.
Raise seat and tighten adjustment knob securely.
•
•
CHECK BRAKE SYSTEM
Afteryoulearnhowtooperateyourtractor,checktoseethat
the brake is operating properly. See “TO CHECK BRAKE”
in the Service and Adjustments section of this manual.
SEAT
SEAT PAN
SHOULDER
BOLT
✓CHECKLIST
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE
WISHTOASSURETHATYOURECEIVETHEBESTPER-
FORMANCEANDSATISFACTIONFROMTHISQUALITY
PRODUCT.
00835
PLEASE REVIEW THE FOLLOWING CHECKLIST:
✓
✓
✓
All assembly instructions have been completed.
No remaining loose parts in carton.
Battery is properly prepared and charged. (Minimum
1 hour at 6 amps).
FLAT WASHER
ADJUSTMENT
KNOB
Fig. 3
✓
✓
Seat is adjusted comfortably and tightened securely.
All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
NOTE:Youmaynowrollyourtractorofftheskid. Followthe
instructions below to remove the tractor from the skid.
WARNING:Beforestarting,read,understandandfollow
all instructions in the Operation section of this manual. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other people and objects.
✓
Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
✓
✓
TOROLLTRACTOROFFSKID (SeeOperation
section for location and function of controls)
Check wiring. See that all connections are still secure
and wires are properly clamped.
•
•
•
•
•
Raise attachment lift lever to its highest position.
Releaseparkingbrakebydepressingclutch/brakepedal.
Place gearshift lever in neutral (N) position.
Roll tractor forward off skid.
Removebandingholdingthedeflectorshieldupagainst
tractor.
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
✓
Engine oil is at proper level.
Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
✓
✓
Become familiar with all controls, their location and
function. Operate them before you start the engine.
Be sure brake system is in safe operating condition.
Be sure Operator Presence System and Reverse Op-
eration System (ROS) are working properly (See the
Operation and Maintenance sections in this manual).
Continue with the instructions that follow.
CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory
for shipping purposes. Correct tire pressure is important
for best cutting performance.
✓
✓
•
Reduce tire pressure to PSI shown on tires.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-
ing.
FAST
SLOW
REVERSE
HIGH
LOW
NEUTRAL
CHOKE
IGNITION SWITCH
P
ENGINE START
ENGINE ON
PARKING BRAKE
REVERSE
OPERATION
SYSTEM (ROS)
PARKING BRAKE PARKING BRAKE
ENGINE OFF
LOCKED
UNLOCKED
OIL PRESSURE
BATTERY
REVERSE
FUEL
FORWARD
OVER TEMP
LIGHT
MOWER HEIGHT
MOWER LIFT
15
15
ATTACHMENT
CLUTCH ENGAGED
ATTACHMENT
CLUTCH DISENGAGED
BRAKE/CLUTCH
PEDAL
SLOPE HAZARDS
KEEP AREA CLEAR
(SEE SAFETY RULES SECTION)
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
LIGHTS ON
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
FREE WHEEL
(Automatic Models only)
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
DANGER, KEEP HANDS
AND FEET AWAY
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.
Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety inform-
ation about hazards which can
result in death, serious injury
and/or property damage.
HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious injury
and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.
Save this manual for future reference.
ATTACHMENT
ROS "ON"
IGNITION
CLUTCH LEVER
POSITION
SWITCH
LIFT LEVER
PLUNGER
LIGHT SWITCH
ATTACHMENT
LIFT LEVER
THROTTLE/CHOKE
CONTROL
HEIGHT
ADJUSTMENT
INDICATOR
CLUTCH/BRAKE
PEDAL
PARKING
BRAKE
GEAR SHIFT
LEVER
02829
Fig. 4
Our tractors conform to the safety standards of the American National Standards Institute.
ATTACHMENT CLUTCH LEVER - Used to engage the
LIFT LEVER PLUNGER - Used to release attachment lift
mower blades, or other attachments mounted to your
lever when changing its position.
tractor.
LIGHT SWITCH - Turns the headlights on and off.
PARKING BRAKE - Locks clutch/brake pedal into the
brake position.
REVERSE OPERATION SYSTEM (ROS) “ON” POSI-
TION - Allows operation of mower deck or other powered
attachment while in reverse.
THROTTLE/CHOKE CONTROL - Used for starting and
controlling engine speed.
ATTACHMENT LIFT LEVER - Used to raise, lower, and
adjust the mower deck or other attachments mounted to
your tractor.
CLUTCH/BRAKEPEDAL-Usedfordeclutchingandbrak-
ing the tractor and starting the engine.
GEARSHIFT LEVER - Selects the speed and direction
of the tractor.
IGNITION SWITCH - Used for starting and stopping the
engine.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating
your tractor or performing any adjustments or repairs. We recommend standard safety
glasses or a wide vision safety mask worn over spectacles.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY
TO BE DISCHARGED, (DEAD).
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 5)
NOTE: Under certain conditions when tractor is standing
idlewiththeenginerunning, hotengineexhaustgasesmay
cause “browning” of grass. To eliminate this possibility, al-
ways stop engine when stopping tractor on grass areas.
Your tractor is equipped with an operator presence sens-
ing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
CAUTION: Always stop tractor com-
pletely,asdescribedabove,beforeleav-
ing the operator's position; to empty
grass catcher, etc.
•
Depress clutch/brake pedal into full “BRAKE” position
and hold.
Place parking brake lever in “ENGAGED” position
and release pressure from clutch/brake pedal. Pedal
shouldremainin“BRAKE”position. Makesureparking
brake will hold tractor secure.
•
TO USE THROTTLE CONTROL (See Fig. 5)
Always operate engine at full throttle.
ATTACHMENT CLUTCH
LEVER "ENGAGED"
POSITION
•
Operating engine at less than full throttle reduces the
battery charging rate.
•
Full throttle offers the best bagging and mower perfor-
mance.
IGNITION KEY
THROTTLE/
CHOKE
"DISENGAGED"
POSITION
CONTROL
LEVER
TO MOVE FORWARD AND BACKWARD
(See Fig. 5)
The direction and speed of movement is controlled by the
gearshift lever.
PARKING BRAKE
"ENGAGED"
POSITION
"BRAKE"
POSITION
•
Start tractor with clutch/brake pedal depressed and
gearshift lever in neutral (N) position.
•
•
Move gearshift lever to desired position.
Slowly release clutch/brake pedal to start move-
ment.
GEAR SHIFT
LEVER
CLUTCH/BRAKE
PEDAL "DRIVE"
POSITION
PARKING BRAKE
"DISENGAGED"
POSITION
IMPORTANT: BRING TRACTOR TO A COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE.
Fig. 5
STOPPING (See Fig. 5)
MOWER BLADES -
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 5)
The position of the attachment lift lever determines the
cutting height.
•
•
•
To stop mower blades, place attachment clutch control
in the “DISENGAGED” position ( ).
GROUND DRIVE -
Grasp lift lever.
Press plunger with thumb and move lever to desired
position.
•
To stop ground drive, depress clutch/brake pedal into
full “BRAKE” position.
Move gearshift lever to neutral position.
•
The cutting height range is approximately 1-1/2 to 4".
The heights are measured from the ground to the blade tip
withtheenginenotrunning. Theseheightsareapproximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
ENGINE -
Move throttle control between half and full speed (fast)
position.
•
NOTE:Failuretomovethrottlecontrolbetweenhalfandfull
speed (fast) position, before stopping may cause engine
to “backfire”.
•
The average lawn should be cut to approximately
2-1/2" during the cool season and to over 3" during hot
months. For healthier and better looking lawns, mow
often and after moderate growth.
•
Turn ignition key to “STOP” position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
•
For best cutting performance, grass over 6" in height
should be mowed twice. Make the first cut relatively
high; the second to desired height.
•
Never use the choke to stop the engine.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
REVERSE OPERATION SYSTEM (ROS)
"ENGAGED" POSITION
Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse
direction with the attachment clutch engaged will shut off
the engine unless ignition key is placed in the ROS "ON"
position.
ATTACHMENT
LIFT LEVER
HIGH POSITION
LOW
POSITION
WARNING: Backing up with the attachment clutch en-
gaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged. Do not mow in reverse unless
absolutely necessary.
ATTACHMENT
CLUTCH LEVER
"DISENGAGED"
POSITION
USINGTHEREVERSEOPERATIONSYSTEM(SeeFig.6)
Only use if you are certain no children or other bystanders
will enter the mowing area.
DEFLECTOR
SHIELD
•
•
Depress clutch/brake pedal all the way down and hold.
Withenginerunning,turnignitionkeycounterclockwise
to ROS "ON" position.
Look down and behind before backing.
Move gear shift lever to reverse (R) position and slowly
release clutch/brake pedal to start movement.
Fig. 7
TO OPERATE ON HILLS
•
•
WARNING: Do not drive up or down
hills with slopes greater than 15° and
do not drive across any slope.
•
When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.
•
Choose the slowest speed before starting up or down
hills.
•
•
Avoid stopping or changing speed on hills.
If slowing is necessary, move throttle control lever to
slower position.
•
•
If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake.
Move gearshift lever to 1st gear. Be sure you have
allowed room for tractor to roll slightly as you restart
movement.
Torestartmovement, slowlyreleaseparkingbrakeand
clutch/brake pedal.
Make all turns slowly.
ROS "ON"
POSITION
ENGINE "ON" POSITION
(NORMAL OPERATING)
Fig. 6
•
•
TO OPERATE MOWER (See Fig. 7)
Your tractor is equipped with an operator presence sens-
ing switch. Any attempt by the operator to leave the seat
withtheenginerunningandtheattachmentclutchengaged
will shut off the engine. You must remain fully and centrally
positioned in the seat to prevent the engine from hesitating
or cutting off when operating your equipment on rough,
rolling terrain or hills.
TO TRANSPORT
•
•
•
Raiseattachmentlifttohighestpositionwithattachment
lift control.
When pushing or towing your tractor, be sure gearshift
lever is in neutral (N) position.
Do not push or tow tractor at more than five (5) MPH.
•
•
Select desired height of cut.
Start mower blades by engaging attachment clutch
control.
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, be sure hood is closed
and secured to tractor. Use an appropriate means of tying
hood to tractor (rope, cord, etc.).
TO STOP MOWER BLADES (See Fig. 7)
Disengage attachment clutch control.
TOWINGCARTSANDOTHERATTACHMENTS
CAUTION:Donotoperatethemowerwithout
eithertheentiregrasscatcher,onmowersso
equipped, or the deflector shield in place.
Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your trac-
tor. Use common sense when towing. Too heavy of a load,
while on a slope, is dangerous. Tires can lose traction with
the ground and cause you to lose control of your tractor.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO START ENGINE (See Fig. 4)
When starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.
•
Sit on seat in operating position, depress clutch/brake
pedal and set parking brake.
•
•
Check engine oil with tractor on level ground.
•
•
•
Place gear shift lever in neutral position.
Move attachment clutch to “DISENGAGED” position.
Move throttle control to choke position.
Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
NOTE: Before starting, read the warm and cold starting
procedures below.
•
•
For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Maintenance section of this manual).
To change engine oil, see the Maintenance section in
this manual.
•
Insertkeyintoignitionandturnkeyclockwiseto“START”
position and release key as soon as engine starts.
Do not run starter continuously for more than fifteen
seconds per minute. If the engine does not start after
several attempts, move throttle control to fast position,
wait a few minutes and try again. If engine still does
not start, move the throttle control back to the choke
position and retry.
ADD GASOLINE
•
Fill fuel tank to bottom of filler neck. Do not overfill. Use
fresh,clean,regularunleadedgasolinewithaminimum
of 87 octane. (Use of leaded gasoline will increase
carbon and lead oxide deposits and reduce valve life).
Donotmixoilwithgasoline. Purchasefuelinquantities
thatcanbeusedwithin30daystoassurefuelfreshness.
WARM WEATHER STARTING (50°F/10°C and above)
•
When engine starts, move the throttle control to the
fast position.
•
The attachments and ground drive can now be used. If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
COLD WEATHER STARTING (50°F/10°C and below)
IMPORTANT: WHENOPERATINGINTEMPERATURESBELOW
32°F (0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE
TO HELP ENSURE GOOD COLD WEATHER STARTING.
•
When engine starts, allow engine to run with the
throttle control in the choke position until the engine
runs roughly, then move throttle control to fast posi-
tion. This may require an engine warm-up period from
several seconds to several minutes, depending on the
temperature.
CAUTION: Alcoholblendedfuels(calledgasohol
or using ethanol or methanol) can attract mois-
ture which leads to separation and formation of
acids during storage. Acidic gas can damage
the fuel system of an engine while in storage. To
avoid engine problems, the fuel system should
be emptied before storage of 30 days or longer.
Drain the gas tank, start the engine and let it run
untilthefuellinesandcarburetorareempty. Use
freshfuelnextseason. SeeStorageInstructions
for additional information. Never use engine or
carburetor cleaner products in the fuel tank or
permanent damage may occur.
•
The attachments can also be used during the engine
warm-up period.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures(below32°F/0°C)thecarburetorfuelmixture
may need to be adjusted for best engine performance. See
“TO ADJUST CARBURETOR” in the Service and Adjust-
ments section of this manual.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
MOWING TIPS
•
Mowershouldbeproperlyleveledforbestmowingper-
formance. See"TOLEVELMOWERHOUSING"inthe
Service and Adjustments section of this manual.
The left hand side of mower should be used for trim-
ming.
•
•
Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of the
machine. This will result in a more even distribution of
clippings and more uniform cutting.
•
When mowing large areas, start by turning to the right
so that clippings will discharge away from shrubs,
fences, driveways, etc. After one or two rounds, mow
in the opposite direction making left hand turns until
finished (See Fig. 8).
Fig. 8
•
If grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clip-
pings. Make first cut relatively high; the second to the
desired height.
•
•
Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps. Allow grass to
dry before mowing.
Always operate engine at full throttle when mow-
ing to assure better mowing performance and proper
discharge of material. Regulate ground speed by se-
lecting a low enough gear to give the mower cutting
performance as well as the quality of cut desired.
When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.
•
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
BEFORE
EACH
USE
EVERY
8
HOURS
EVERY
25
HOURS
EVERY
50
HOURS
EVERY
100
HOURS
EVERY
SEASON
BEFORE
STORAGE
MAINTENANCE
SCHEDULE
Check Brake Operation
Check Tire Pressure
T
R
A
C
T
Check Operator Presence & ROS Systems
Check for Loose Fasteners
Check/Replace Mower Blades
Lubrication Chart
3
4
0
Check Battery Level
R
Clean Battery and Terminals
Check Transaxle Cooling
Check Mower Levelness
Check V-Belts
Check Engine Oil Level
Change Engine Oil (with oil filter)
Change Engine Oil (without oil filter)
Clean Air Filter
1,2
1,2
E
N
G
I
N
E
2
2
Clean Air Screen
Inspect Muffler/Spark Arrester
Replace Oil Filter (If equipped)
Clean Engine Cooling Fins
Replace Spark Plug
1,
2
2
Replace Air Filter Paper Cartridge
Replace Fuel Filter
2
1 - Change more often when operating under a heavy load or in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
3 - Replace blades more often when mowing in sandy soil.
4 - Not required if equipped with maintenance-free battery.
LUBRICATION CHART
dSPINDLE ZERK
GENERAL RECOMMENDATIONS
dSPINDLE ZERK
The warranty on this tractor does not cover items that have
beensubjectedtooperatorabuseornegligence. Toreceive
full value from the warranty, operator must maintain tractor
as instructed in this manual.
dFRONT WHEEL
dFRONT WHEEL
BEARING ZERK
BEARING ZERK
Some adjustments will need to be made periodically to
properly maintain your tractor.
At least once a season, check to see if you should make
any of the adjustments described in the Service and
Adjustments section of this manual.
eENGINE
• At least once a year you should replace the spark plug,
clean or replace air filter, and check blades and belts
for wear. A new spark plug and clean air filter assure
proper air-fuel mixture and help your engine run better
and last longer.
cGEARSHIFT
PIVOTS
BEFORE EACH USE
cSAE 30 OR 10W30 MOTOR OIL
dGENERAL PURPOSE GREASE
eREFER TO MAINTENANCE “ENGINE” SECTION
•
•
•
•
Check engine oil level.
Check brake operation.
Check tire pressure.
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH
HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL
ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF
THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST
BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE
LUBRICANT SPARINGLY.
Check operator presence and
ROS systems for proper operation.
Check for loose fasteners.
•
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
BLADE CARE
TRACTOR
Forbestresultsmowerbladesmustbekeptsharp. Replace
Always observe safety rules when performing any
maintenance.
bent or damaged blades.
CAUTION:Useonlyareplacementbladeap-
provedbythemanufacturerofyourtractor.
Using a blade not approved by the manu-
facturer of your tractor is hazardous, could
damageyourtractorandvoidyourwarranty.
BRAKE OPERATION
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be checked and adjusted. (See
“TO CHECK BRAKE” in the Service and Adjustments
section of this manual).
BLADE REMOVAL (See Fig. 10)
TIRES
•
Raise mower to highest position to allow access to
blades.
•
•
•
Maintain proper air pressure in all tires (See the sides
of tires for proper PSI).
Keep tires free of gasoline, oil, or insect control
chemicals which can harm rubber.
Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: Protect your hands with gloves and/or wrap blade
with heavy cloth.
•
•
Remove blade bolt by turning counterclockwise.
Install new or resharpened blade with stamped "THIS
SIDE UP" facing deck and mandrel assembly.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL
ASSEMBLY.
NOTE: To seal tire punctures and prevent flat tires due
to slow leaks, tire sealant may be purchased from your
local parts dealer. Tire sealant also prevents tire dry rot
and corrosion.
•
Install and tighten blade bolt securely (45-55 Ft. Lbs.
torque).
OPERATOR PRESENCE SYSTEM AND REVERSE
OPERATION SYSTEM (ROS) (See Fig. 9)
Be sure operator presence and reverse operation systems
are working properly. If your tractor does not function as
described, repair the problem immediately.
IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.
MANDREL ASSEMBLY
BLADE
•
The engine should not start unless the brake pedal is
fully depressed, and the attachment clutch control is
in the disengaged position.
BLADE BOLT
STAR
(SPECIAL)
CHECK OPERATOR PRESENCE SYSTEM
•
•
•
Whentheengineisrunning,anyattemptbytheoperator
to leave the seat without first setting the parking brake
should shut off the engine.
When the engine is running and the attachment clutch
is engaged, any attempt by the operator to leave the
seat should shut off the engine.
CENTER HOLE
Fig. 10
BATTERY
Yourtractorhasabatterychargingsystemwhichissufficient
for normal use. However, periodic charging of the battery
with an automotive charger will extend its life.
The attachment clutch should never operate unless
the operator is in the seat.
•
•
•
•
Keep battery and terminals clean.
Keep battery bolts tight.
Keep small vent holes open.
Recharge at 6-10 amperes for 1 hour.
CHECK REVERSE OPERATION (ROS) SYSTEM
•
When the engine is running with the ignition switch in
the engine "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should shut off the engine.
NOTE:Theoriginalequipmentbatteryonyourtractorismain-
tenancefree.Donotattempttoopenorremovecapsorcov-
ers.Addingorcheckinglevelofelectrolyteisnotnecessary.
•
When the engine is running with the ignition switch
in the ROS "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should NOT shut off the engine.
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to “leak” power.
•
•
Raise seat.
Disconnect BLACK battery cable first then RED bat-
tery cable and remove battery from tractor.
•
•
Rinse the battery with plain water and dry.
Cleanterminalsandbattery cableends withwirebrush
until bright.
ROS "ON"
POSITION
ENGINE "ON" POSITION
(NORMAL OPERATING)
•
•
Coat terminals with grease or petroleum jelly.
Reinstall battery (See “REPLACING BATTERY" in the
Service and Adjustments section of this manual).
Fig. 9
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
TO CHANGE ENGINE OIL (See Fig. 12)
Determine temperature range expected before oil change.
All oil must meet API service classification C.
V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.
•
•
•
•
Be sure tractor is on level surface.
Oil will drain more freely when warm.
Catch oil in a suitable container.
Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
TRANSAXLE MAINTENANCE
Keep transaxle free from build-up of dirt and chaff which
can restrict cooling.
Do not attempt to clean transaxle while engine is running
or while the transaxle is hot. To prevent possible damage
to seals, do not use high pressure water or steam to clean
transaxle.
CAUTION: If engine has been operated
for an extended period of time immedi-
ately prior to draining oil, oil will be hot.
ENGINE
OIL DRAIN HOLE
LUBRICATION
Only use high quality detergent oil rated with API service
classification SG-SL. Select the oil’s SAE viscosity grade
according to your expected operating temperature.
OIL
DRAIN
PLUG
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improvestartingincoldweather,theywillresultinincreased
oilconsumptionwhenusedabove32°F. Checkyourengine
oil level more frequently to avoid possible engine damage
from running low on oil.
Change the oil after every 25 hours of operation or at least
once a year if the tractor is not used for 25 hours in one
year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation. Tighten oil fill
cap/dipstick securely each time you check the oil level.
OIL DRAIN
EXTENSION
Fig. 12
•
•
•
•
•
•
Slide oil drain extension under oil drain hole (drain hole
maybeflushwithorprotrudefromengineblocksidewall).
Make sure back face of oil drain extension is flush with
SAE VISCOSITY GRADES
engine side wall.
SAE 30
Make sure bottom lip of oil drain extension is lined up
with bottom of oil drain hole.
Position a container to catch oil directly under front end
5W-30
-20
0
30
32 40
0
100
60
80
F
of oil drain extension.
C
-20
10
-30
-10
20
30
40
Slide a 1/2” (12 point) socket mounted on an extension
onto oil drain plug.
Loosen plug while holding the oil drain extension firmly
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
oil_visc_chart1_e
Fig. 11
in place.
•
•
Drain oil into container.
After oil has drained completely, reinstall oil drain plug.
(Do not tighten more than 13 Ft-Lb's)
•
•
Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCTSPECIFICATIONS”sectionofthismanual.
Use gauge on oil fill cap/dipstick for checking level.
Be sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick. Tighten
cap onto the tube securely when finished.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CLEAN AIR SCREEN
IN-LINE FUEL FILTER (See Fig. 14)
The fuel filter should be replaced once each season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers.
•
•
•
•
With engine cool, remove filter and plug fuel line sec-
tions.
AIR FILTER
Your engine will not run properly using a dirty air filter.
Service air cleaner more often under dusty conditions. See
Engine Manual.
Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
Be sure there are no fuel line leaks and clamps are
properly positioned.
Immediately wipe up any spilled gasoline.
MUFFLER
Inspect and replace corroded muffler and spark arrester
(if equipped) as it could create a fire hazard and/or dam-
age.
CLAMP
CLAMP
SPARK PLUGS
Replace spark plugs at the beginning of each mowing sea-
son or after every 100 hours of use, whichever comes first.
Spark plug type and gap setting is shown in "PRODUCT
SPECIFICATIONS" section of this manual.
FUEL
FILTER
Fig. 15
ENGINE COOLING SYSTEM (See Fig. 13)
Debris may clog the engine's air cooling system. Remove
blower housing and clean the area shown to prevent over-
heating and engine damage.
CLEANING
•
•
•
Clean engine, battery, seat, finish, etc. of all foreign
matter.
Keep finished surfaces and wheels free of all gasoline,
oil, etc.
Protect painted surfaces with automotive type wax.
CLEAN OUT CHAFF AND DEBRIS
AIR SCREEN
We do not recommend using a garden hose or pressure
washer to clean your tractor unless the engine and trans-
mission are covered to keep water out. Water in engine or
transmission will shorten the useful life of your tractor. Use
compressed air or a leaf blower to remove grass, leaves
and trash from tractor and mower.
02744
Fig. 13
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
•
•
•
•
•
•
Depress clutch/brake pedal fully and set parking brake.
Place gearshift lever in neutral position.
Place attachment clutch in “DISENGAGED” position.
Turn ignition key to “STOP” and remove key.
Make sure the blades and all moving parts have completely stopped.
Disconnectsparkplugwirefromsparkplugandplacewirewhereitcannotcomeincontactwithplug.
TO REMOVE MOWER (See Fig. 15)
Mowerwillbeeasiertoremovefromtherightsideoftractor.
TO INSTALL MOWER (See Fig. 15)
•
•
Raise attachment lift lever to its highest position.
Slide mower under tractor with deflector shield to right
side of tractor.
•
•
Place attachment clutch in “DISENGAGED” position.
Move attachment lift lever forward to lower mower to
its lowest position.
•
•
Lower lift lever to its lowest position.
Connect front links to mower deck and secure with
retainer springs..
•
•
Roll belt off engine pulley.
Removesmallretainerspring,andremoveclutchspring
off pulley bolt.
•
•
•
•
•
•
Connect suspension arms to rear deck brackets and
secure with retainer springs.
Connect anti-swaybar to chassis bracket and secure
with retainer spring.
Pushclutchcablehousingguideintobracket, slidecol-
lar onto guide and secure with large retainer spring.
Place flat washer and clutch spring on idler pulley bolt
and secure with small retainer spring.
•
•
•
•
•
Remove large retainer spring, slide collar off and push
housing guide out of bracket.
Disconnect anti-swaybar from chassis bracket by re-
moving retainer spring.
Disconnect suspension arms from rear deck brackets
by removing retainer springs.
Disconnect front links from deck by removing retainer
springs.
Make sure belt is inside the belt keeper at the idler and
on both sides of the wire belt keeper as shown.
Install belt onto engine pulley.
Raise lift lever to raise suspension arms. Slide mower
out from under tractor.
IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL
MOWER PULLEY GROOVES.
IMPORTANT:IFANATTACHMENTOTHERTHANTHEMOWER
DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE
THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO
SQUARE HOLE IN FRAME.
SMALL RETAINER SPRING
FLAT WASHER
WIRE BELT KEEPER
SUSPENSION ARMS
CLUTCH SPRING
BELT KEEPER
SQUARE HOLE
RETAINER SPRING
ANTI-SWAY BAR
ENGINE PULLEY
FRONT LINK
COLLAR
HOUSING GUIDE
RETAINER SPRINGS
(BOTH SIDES)
02845
LARGE
RETAINER
SPRING
BRACKET
DEFLECTOR SHIELD
CLUTCH SPRING
Fig. 15
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
Checkadjustmentonrightsideoftractor. Measuredistance
TO LEVEL MOWER HOUSING
“D” directly in front and behind the mandrel at bottom edge
Adjust the mower while tractor is parked on level ground
or driveway. Make sure tires are properly inflated (See
“PRODUCT SPECIFICATIONS” section of this manual). If
tires are over or underinflated, you will not properly adjust
your mower.
of mower housing as shown.
•
•
•
•
Before making any necessary adjustments, check that
both front links are equal in length.
If links are not equal in length, adjust one link to same
length as other link.
To lower front of mower loosen nut “E” on both front
links an equal number of turns.
When distance “D” is 1/8" to 1/2" lower at front than
rear, tighten nuts “F” against trunnion on both front
links.
SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)
•
•
Raise mower to its highest position.
At the midpoint of both sides of mower, measure height
from bottom edge of mower to ground. Distance “A”
on both sides of mower should be the same or within
1/4" of each other.
•
•
•
If adjustment is necessary, make adjustment on one
•
To raise front of mower, loosen nut “F” from trunnion on
both front links. Tighten nut “E” on both front links an
equal number of turns. The two front links must remain
equal in length.
Whendistance“D”is1/8"to1/2"loweratfrontthanrear,
tighten nut “F” against trunnion on both front links.
side of mower only.
To raise one side of mower, tighten lift link adjustment
nut on that side.
To lower one side of mower, loosen lift link adjustment
nut on that side.
•
•
Recheck side-to-side adjustment.
NOTE: Each full turn of adjustment nut will change mower
height about 1/8".
•
MANDREL
Recheck measurements after adjusting.
BOTTOM EDGE
OF MOWER TO
GROUND
BOTTOM EDGE
OF MOWER TO
GROUND
“D”
“D”
Fig. 18
A
A
GROUND LINE
BOTH FRONT LINKS MUST BE EQUAL IN LENGTH
Fig. 16
SUSPENSION ARM
NUT “F”
LIFT LINK
ADJUSTMENT NUT
NUT “E”
TRUNNION
Fig. 17
FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE
FOLLOWINGFRONT-TO-BACKADJUSTMENTISNECESSARY,
BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO
MOWER WILL STAY LEVEL SIDE-TO-SIDE.
FRONT LINKS
To obtain the best cutting results, the mower housing
should be adjusted so that the front is approximately 1/8"
to 1/2" lower than the rear when the mower is in its high-
est position.
Fig. 19
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
TO REPLACE MOTION DRIVE BELT
(See Fig. 21)
TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 20)
Park the tractor on level surface. Engage parking brake.
For assistance, there is a belt installation guide decal on
bottom side of left footrest.
The mower blade drive belt may be replaced without tools.
Park the tractor on level surface. Engage parking brake.
BELT REMOVAL -
BELT REMOVAL -
•
Place attachment clutch in “DISENGAGED” position.
•
Remove mower (See “TO REMOVE MOWER” in this
section of manual).
•
Move attachment lift lever forward to lower mower to
its lowest position.
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers.
•
•
•
Roll belt off engine pulley.
Work belt off both mandrel pulleys and idler pulleys.
Pull belt away from mower.
•
•
•
Remove belt from stationary idler and clutching idler.
Remove belt downward from around engine pulley.
Pull belt slack toward rear of tractor. Remove belt
upwards from transaxle pulley by deflecting belt keep-
ers.
BELT INSTALLATION -
•
Work new belt around both mandrel pulleys and idler
pulleys.
•
•
Install new belt into engine pulley groove.
Make sure belt is inside the belt keeper at the idler and
on both sides of the wire belt keeper as shown.
•
Remove belt from center span keeper and pull belt
away from tractor.
BELT INSTALLATION -
•
IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL
MOWER PULLEY GROOVES.
Carefully work new belt down between transaxle belt
keepers and onto the input pulley.
•
•
Slide belt into the center span keeper.
Pull belt toward front of tractor and roll around the top
groove of engine pulley.
Install belt through stationary idler and clutching
idler.
Make sure belt is in all pulley grooves and inside all
belt guides and keepers.
WIRE BELT KEEPER
BELT KEEPER
MANDREL
PULLEY
•
•
•
Install mower (See “TO INSTALL MOWER” in this sec-
tion of manual).
ENGINE
PULLEY
IDLER
PULLEYS
ENGINE
PULLEY
MANDREL
PULLEY
CLUTCHING
IDLER
02844
STATIONARY
IDLER
Fig. 20
TO CHECK BRAKE
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be serviced.
CENTER SPAN
KEEPER
TRANSAXLE
PULLEY
You may also check brake by:
1. Park tractor on a level, dry concrete or paved surface,
depress clutch/brake pedal all the way down and en-
gage parking brake.
2. Place gear shift lever in neutral (N) position.
The rear wheels must lock and skid when you try to manu-
ally push the tractor forward. If the rear wheels rotate, then
the brake needs to be serviced. Contact a qualified service
center.
Fig. 21
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
TRANSAXLE GEAR SHIFT LEVER NEUTRAL
ADJUSTMENT (See Fig. 22)
Thetransaxleshouldbeinneutralwhenthegearshiftleveris
inneutral(lockgate)position.Theadjustmentispresetatthe
factory;however,ifadjustmentisneeded,proceedasfollows:
WASHERS
RETAINING
RING
AXLE
COVER
•
Make sure transaxle is in neutral.
NOTE: When the tractor rear wheels move freely, the
transaxle is in neutral.
•
Loosen adjustment bolt in front of the right rear
wheel.
SQUARE KEY (REAR
WHEEL ONLY)
•
•
Position the gear shift lever in the neutral position.
Tighten adjustment bolt securely.
Fig. 23
TO START ENGINE WITH A WEAK BATTERY
(See Fig. 24)
NOTE: Ifadditionalclearanceisneededtogettoadjustment
bolt, move mower deck height to the lowest position.
NEUTRAL
LOCK GATE
WARNING: Lead-acid batteries gen-
erate explosive gases. Keep sparks,
flameandsmokingmaterialsawayfrom
batteries. Always wear eye protection
when around batteries.
GEARSHIFT LEVER
If your battery is too weak to start the engine, it should be
recharged. (See "BATTERY" in the Maintenance section
of this manual).
If “jumper cables” are used for emergency starting, follow
this procedure:
ADJUSTMENT
BOLT
IMPORTANT: YOURTRACTORISEQUIPPEDWITHA12VOLT
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT
SYSTEM.DONOTUSEYOURTRACTORBATTERYTOSTART
OTHER VEHICLES.
Fig. 22
TO ADJUST STEERING WHEEL ALIGNMENT
If steering wheel crossbars are not horizontal (left to right)
whenwheelsarepositionedstraightforward,removesteer-
ing wheel and reassemble per instructions in the Assembly
section of this manual.
TO ATTACH JUMPER CABLES -
•
Connect one end of the RED cable to the POSITIVE
(+) terminal of each battery(A-B), taking care not to
short against tractor chassis.
•
•
ConnectoneendoftheBLACKcabletotheNEGATIVE
FRONT WHEEL TOE-IN/CAMBER
(-) terminal (C) of fully charged battery.
Your new tractor front wheel toe-in and camber is set at the
factory and is normal. The front wheel toe-in and camber
are not adjustable. If damage has occurred to affect the
factory set front wheel toe-in or camber, contact a qualified
service center.
Connect the other end of the BLACK cable (D) to good
chassis ground, away from fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER -
•
BLACK cable first from chassis and then from the fully
charged battery.
RED cable last from both batteries.
TO REMOVE WHEEL FOR REPAIRS
(See Fig. 23)
•
•
•
Block up axle securely.
Removeaxlecover,retainingringandwasherstoallow
wheel removal (rear wheel contains a square key - Do
not lose).
•
•
Repair tire and reassemble.
On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.
•
•
Replace washers and snap retaining ring securely in
axle groove.
Replace axle cover.
WEAK OR DEAD
BATTERY
FULLY CHARGED
BATTERY
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
Fig. 24
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
REPLACING BATTERY (See Fig. 25)
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse. The
WARNING: Do not short battery
terminals by allowing a wrench or any
other object to contact both terminals
at the same time. Before connecting
battery, remove metal bracelets,
wristwatch bands, rings, etc. Positive
terminal must be connected first to
prevent sparking from accidental
grounding.
fuse holder is located behind the dash.
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 26)
•
•
•
Raise hood.
Unsnap headlight wire connector.
Standinfrontoftractor. Grasphoodatsides, tilttoward
engine and lift off of tractor.
•
To replace, reverse above procedure.
•
•
Lift seat pan to raised position.
DisconnectBLACKbatterycablefirstthenREDbattery
cable and carefully remove battery from tractor.
•
•
Install new battery with terminals in same position as
old battery.
First connect RED battery cable to positive (+) terminal
with bolt and nut as shown. Tighten securely. Slide
terminal cover over terminal.
HOOD
•
•
Connect BLACK grounding cable to negative (-) ter-
minal with remaining bolt and nut. Tighten securely.
Lower seat pan.
SEAT PAN
HEADLIGHT
WIRE
CONNECTOR
02602
ꢀꢁꢂꢃꢄ
TERMINAL
NUT
COVER
BOLT
POSITIVE
NEGATIVE
(RED)
(BLACK)
CABLE
Fig. 26
02603
CABLE
Fig. 25
ENGINE
TO REPLACE HEADLIGHT BULB
•
•
Raise hood.
TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is nec-
essary, see engine manual.
Pull bulb holder out of the hole in the backside of the
grill.
•
•
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
Close hood.
TO ADJUST CHOKE CONTROL
The choke control has been preset at the factory and ad-
justment should not be necessary. If adjustment is neces-
sary, see engne manual.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
TO ADJUST CARBURETOR
•
Check wiring. See electrical wiring diagram in the
Repair Parts section.
Your carburetor is not adjustable. If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
Immediately prepare your tractor for storage at the end
of the season or if the tractor will not be used for 30 days
or more.
ENGINE
FUEL SYSTEM
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS
FROMFORMINGINESSENTIALFUELSYSTEMPARTSSUCH
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM
OF AN ENGINE WHILE IN STORAGE.
WARNING: Neverstorethetractorwith
gasoline in the tank inside a building
where fumes may reach an open flame
orspark. Allowtheenginetocoolbefore
storing in any enclosure.
TRACTOR
•
•
•
Empty the fuel tank by starting the engine and let it run
until the fuel lines and carburetor are empty.
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
Removemowerfromtractorforwinterstorage. Whenmower
istobestoredforaperiodoftime,cleanitthoroughly,remove
all dirt, grease, leaves, etc. Store in a clean, dry area.
•
Clean entire tractor (See “CLEANING” in the Mainte-
nance section of this manual).
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in mini-
mizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
•
Inspect and replace belts, if necessary (See belt re-
placement instructions in the Service and Adjustments
section of this manual).
•
•
Lubricate as shown in the Maintenance section of this
manual.
Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
ENGINE OIL
•
Touch up all rusted or chipped paint surfaces; sand
Drain oil (with engine warm) and replace with clean en-
gine oil. (See “ENGINE” in the Maintenance section of
this manual).
lightly before painting.
BATTERY
•
•
CYLINDER(S)
Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during
long periods of storage, battery cables should be dis-
connected and battery cleaned thoroughly (see “TO
CLEAN BATTERY AND TERMINALS” in the Mainte-
nance section of this manual).
•
•
Remove spark plug(s).
Pour one ounce of oil through spark plug hole(s) into
cylinder(s).
•
•
•
Turn ignition key to “START” position for a few seconds
to distribute oil.
Replace with new spark plug(s).
•
•
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminals.
If battery is removed from tractor for storage, do not
store battery directly on concrete or damp surfaces.
OTHER
•
•
Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
•
•
If possible, store your tractor indoors and cover it to
give protection from dust and dirt.
Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.
IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND
EXHAUST AREAS ARE STILL WARM.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
CORRECTION
1. Out of fuel.
1. Fill fuel tank.
Will not start
2. Engine not “CHOKED” properly.
3. Engine flooded.
4. Bad spark plug.
5. Dirty air filter.
2. See “TO START ENGINE” in Operation section.
3. Wait several minutes before attempting to start.
4. Replace spark plug.
5. Clean/replace air filter.
6. Dirty fuel filter.
6. Replace fuel filter.
7. Water in fuel.
7. Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
8. Loose or damaged wiring.
8. Check all wiring.
9. Carburetor out of adjustment.
9. See “To Adjust Carburetor” in Service Adjustments
section.
10. Engine valves out of adjustment.
10. Contact an authorized service center/department.
1. Dirty air filter.
1. Clean/replace air filter.
2. Replace spark plug.
3. Recharge or replace battery.
4. Replace fuel filter.
Hard to start
2. Bad spark plug.
3. Weak or dead battery.
4. Dirty fuel filter.
5. Stale or dirty fuel.
5. Empty fuel tank and refill tank with fresh, clean
gasoline.
6. Loose or damaged wiring.
6. Check all wiring.
7. Carburetor out of adjustment.
7. See “To Adjust Carburetor” in Service Adjustments
section.
8. Engine valves out of adjustment.
8. Contact an authorized service center/department.
1. Clutch/brake pedal not depressed.
2. Attachment clutch is engaged.
3. Weak or dead battery.
1. Depress clutch/brake pedal.
2. Disengage attachment clutch.
3. Recharge or replace battery.
4. Replace fuse.
Engine will not
turn over
4. Blown fuse.
5. Corroded battery terminals.
6. Loose or damaged wiring.
7. Faulty ignition switch.
8. Faulty solenoid or starter.
9. Faulty operator presence switch(es).
5. Clean battery terminals.
6. Check all wiring.
7. Check/replace ignition switch.
8. Check/replace solenoid or starter.
9. Contact an authorized service center/department.
1. Weak or dead battery.
1. Recharge or replace battery.
2. Clean battery terminals.
3. Check all wiring.
Engine clicks but
will not start
2. Corroded battery terminals.
3. Loose or damaged wiring.
4. Faulty solenoid or starter.
4. Check/replace solenoid or starter.
1. Cutting too much grass/too fast.
2. Throttle in “CHOKE” position.
1. Raise cutting height/reduce speed.
2. Adjust throttle control.
Loss of power
3. Build-up of grass, leaves and trash under
mower.
3. Clean underside of mower housing.
4. Dirty air filter.
4. Clean/replace air filter.
5. Low oil level/dirty oil.
6. Faulty spark plug.
7. Dirty fuel filter.
5. Check oil level/change oil.
6. Clean and regap or change spark plug.
7. Replace fuel filter.
8. Stale or dirty fuel.
8. Empty fuel tank and refill tank with fresh, clean
gasoline.
9. Water in fuel.
9. Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
10. Spark plug wire loose.
11. Dirty engine air screen/fins.
12. Dirty/clogged muffler.
10. Connect and tighten spark plug wire.
11. Clean engine air screen/fins.
12. Clean/replace muffler.
13. Loose or damaged wiring.
14. Carburetor out of adjustment.
15. Engine valves out of adjustment.
13. Check all wiring.
14. See “To Adjust Carburetor” in Service Adjustments
15. Contact an authorized service center/department.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING POINTS
PROBLEM
CAUSE
CORRECTION
1. Worn, bent or loose blade.
2. Bent blade mandrel.
3. Loose/damaged part(s).
1. Replace blade. Tighten blade bolt.
2. Replace blade mandrel.
3. Tighten loose part(s). Replace damaged parts.
Excessive
vibration
1. Faulty operator-safety presence control
system.
1. Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.
Engine continues
to run when oper-
ator leaves seat
with attachment
clutch engaged
1. Worn, bent or loose blade.
2. Mower deck not level.
1. Replace blade. Tighten blade bolt.
2. Level mower deck.
Poor cut - uneven
3. Buildupofgrass,leaves,ortrashundermower. 3. Clean underside of mower housing.
4. Bent blade mandrel. 4. Replace blade mandrel.
5. Cloggedmowerdeckventholesfrombuildup 5. Clean around mandrels to open vent holes.
ofgrass, leaves, andtrasharoundmandrels.
1. Obstruction in clutch mechanism.
2. Worn/damaged mower drive belt.
3. Frozen idler pulley.
1. Remove obstruction.
2. Replace mower drive belt.
3. Replace idler pulley.
Mower blades will
not rotate
4. Frozen blade mandrel.
4. Replace blade mandrel.
1. Engine speed too slow.
2. Travel speed too fast.
3. Wet grass.
4. Mower deck not level.
5. Low/uneven tire air pressure.
6. Worn, bent or loose blade.
1. Place throttle control in “FAST” position.
2. Shift to slower speed.
3. Allow grass to dry before mowing.
4. Level mower deck.
5. Check tires for proper air pressure.
6. Replace blade. Tighten blade bolt.
7. Clean underside of mower housing.
Poor grass
discharge
7. Buildup of grass, leaves and trash under
mower.
8. Mower drive belt worn.
9. Blades improperly installed.
10. Improper blades used.
8. Replace mower drive belt.
9. Reinstall blades sharp edge down.
10. Replace with blades listed in parts manual.
11. Cloggedmowerdeckventholesfrombuildup 11. Clean around mandrels to open vent holes.
ofgrass, leaves, andtrasharoundmandrels.
1. Switch is “OFF”.
1. Turn switch “ON”.
Headlight(s) not
working
(if so equipped)
2. Bulb(s) or lamp(s) burned out.
3. Faulty light switch.
4. Loose or damaged wiring.
5. Blown fuse.
2. Replace bulb(s) or lamp(s).
3. Check/replace light switch.
4. Check wiring and connections.
5. Replace fuse.
1. Bad battery cell(s).
1. Replace battery.
2. Check/clean all connections.
3. Replace regulator.
Battery will not
charge
2. Poor cable connections.
3. Faulty regulator (if so equipped).
4. Faulty alternator.
4. Replace alternator.
1. Debris on steering plate (if equipped).
2. Motion drive belt worn, damaged, or broken. 2. Replace motion drive belt.
1. See "CLEANING" in the maintenance section.
Loss of drive
3. Axle key missing.
3. Install axle key at rear wheel. See "TO REMOVE
WHEEL" in the Service and Adjustments section.
1. Engine throttle control not set between
half and full speed (fast) position before
stopping engine.
1. Move throttle control between half and full speed
(fast) position before stopping engine.
Engine“backfires”
when turning
engine “OFF”
1. Reverse operation system (ROS) is not
"ON" while mower or other attachment is
engaged.
1. Turn ignition key to ROS "ON" position. See
Operation section.
Engine dies when
tractor is shifted
into reverse
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE NOTES
26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-
als and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or
replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due
to materials or workmanship. This Warranty is subject to the following limitations and exclusions.
1. This warranty does not apply to the engine, transaxle/transmission components, battery (except as noted below) or com-
ponents parts thereof. Please refer to the applicable manufacturer's warranty on these items.
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the pur-
chaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser
unless such return is requested by the manufacturer.
3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find
to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the
Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must
be maintained in accordance with the instructions furnished.
4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original
purchase.
5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accor-
dance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration,
misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard
hardware and normal maintenance.
7. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact:
In Canada contact:
HOP
HOP
Outdoor Products Customer Service Dept.
1030 Stevens Creek Road
Augusta, GA 30907 USA
5855 Terry Fox Way
Mississauga, Ontario
L5V 3E4
giving the model number, serial number and date of purchase of your product and the name and address of the authorized
dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRAN-
TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limi-
tations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which
vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
28
05.18.10 JA
Printed in the U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|