DiamondMax 17
80-160GB
ATA
May 29, 2006
PN: 1938
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Thank you for your interest in Maxtor DiamondMax 17 80-160GB AT hard disk drives. This manual provides technical
information for OEM engineers and systems integrators regarding the installation and use of Maxtor ATA hard drives.
Please do not remove or cover up Maxtor factory-installed drive labels. They contain information required should the
drive ever need repair. Drive repair should be performed only at an authorized repair center. For repair information, con-
tact the Maxtor Product Support Center at 1-800-2MAXTOR.
CAUTION: Maxtor hard drives are precision products. Failure to follow these precautions and guidelines outlined here
may lead to product failure, damage and invalidation of all warranties.
1
Before unpacking or handling a drive, take all proper electrostatic discharge (ESD) precautions, including
personnel and equipment grounding. Stand-alone drives are sensitive to ESD damage.
2
3
4
Before removing drives from their packing material, allow them to reach room temperature.
During handling, never drop, jar, or bump a drive.
Once a drive is removed from the Maxtor shipping container, immediately secure the drive through its
mounting holes within a chassis. Otherwise, store the drive on a padded, grounded, antistatic surface.
Never stack hard drives. This may cause damage to the drive.
Corporate Headquarters
Maxtor Corporation
500 McCarthy Blvd.
Milpitas, California 95035
Tel: 408-894-5000
Fax: 408-362-4740
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Of Contents
Chapter 1
INTRODUCTION
1.2 MANUAL ORGANIZATION.................................................................................................................1-1
Chapter 2
GENERAL DESCRIPTION
Chapter 3
INSTALLATION
3.1 SPACE REQUIREMENTS...................................................................................................................3-1
3.2 UNPACKING INSTRUCTIONS ..........................................................................................................3-2
3.3 Hardware Options.............................................................................................................................3-4
3.3.1 ATA Interface Connector.....................................................................................................3-4
3.3.2 ATA Bus Adapter .................................................................................................................3-7
3.3.3 Adapter Board .....................................................................................................................3-8
3.4 ATA Bus Interface Connector (J1, Section A)...................................................................................3-9
3.5 MOUNTING......................................................................................................................................3-11
3.5.1 Orientation.........................................................................................................................3-11
3.5.2 Clearance ..........................................................................................................................3-13
3.5.3 Ventilation..........................................................................................................................3-13
3.6 FOR SYSTEMS WITH AN ATA ADAPTER BOARD............................................................................3-13
3.6.1 Adapter Board Installation................................................................................................3-13
3.7 TECHNIQUES IN DRIVE CONFIGURATION .....................................................................................3-15
3.7.1 The 8.4-Gigabytes Barrier.................................................................................................3-15
3.7.2 Operating System Limitations ..........................................................................................3-15
3.8 SYSTEM STARTUP AND OPERATION .............................................................................................3-16
i Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Of Contents
Chapter 4
PRODUCT SPECIFICATIONS
4.1 Model Number and Capacity ............................................................................................................4-1
4.2 Drive Configuration...........................................................................................................................4-1
4.3 Performace Specifications ...............................................................................................................4-2
4.4 Physical Dimensions.........................................................................................................................4-2
4.5 Power Requirements........................................................................................................................4-3
4.5.1 Voltage Tolerance ...............................................................................................................4-3
4.11.2 Canadian Emissions Statement........................................................................................4-7
Chapter 5
ATA BUS INTERFACE AND ATA COMMANDS
5.5 COMMAND INTERFACE....................................................................................................................5-2
5.5.1 General Feature Set............................................................................................................5-2
5.5.3 Identify Drive Command......................................................................................................5-5
Chapter 6
SERVICE AND SUPPORT
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive ii
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Figure 3-1
Figure 3-2
Figure 3-3
Figure 3-4
Figure 3-5
Figure 3-6
Figure 3-7
Figure 3-8
Figure 3-9
Figure 3-10
Mechanical Dimensions ......................................................................................................... 3-1
20-Pack Shipping Container .................................................................................................. 3-3
Jumper Locations of the ATA Interface Connector ............................................................... 3-4
ATA Connector and Jumper Locations....................................................................................3-7
J1 DC Power and ATA Bus Combination Connector .............................................................. 3-9
Mounting Dimensions .......................................................................................................... 3-11
Mounting Screw Clearance................................................................................................... 3-12
Lengthwise Airflow Cooling.................................................................................................. 3-13
Crosswise Airflow Cooling.................................................................................................... 3-14
Drive Power Supply and ATA Bus Interface Cables ............................................................. 3-15
iii Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Tables
Table 3-1 AT Jumper Options ............................................................................................................3-5
Table 3-2 LBA Addressing ................................................................................................................ 3-7
Table 3-3 J1 Power Connector, Section A ....................................................................................... 3-9
Table 3-4 Logical Addressing Format ............................................................................................ 3-16
Table 5-1 Supported ATA Commands............................................................................................... 5-2
Table 5-2 Identify Drive Command Parameters................................................................................5-5
viii Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
This chapter gives an overview of the contents of this manual, including the intended
audience, how the manual is organized, terminology, conventions, and references.
1.1
1.2
AUDIENCE
The DiamondMax 17 80-160GB AT hard disk drive product manual is intended for
several audiences. These audiences will include: the end user, installers, developers,
consumer electronics and personal computer original equipment manufacturers
(CE/PC OEM), and distributors. This manual provides information about installation,
principles of operation, interface command implementation, service and support.
MANUAL ORGANIZATION
This manual is organized into the following chapters:
– Chapter 1 – Introduction
– Chapter 2 – General Description
– Chapter 3 – Installation
– Chapter 4 – Product Specifications
– Chapter 5 – ATA Bus Interface and ATA Commands
– Chapter 6 – Service and Support
– Glossary
Maxtor DiamondMax 17 80-160GB AT Hard Drive
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1.3
TERMINOLOGY AND CONVENTIONS
In the Glossary at the back of this manual, you can find definitions for many of the
terms used in this manual. In addition, the following abbreviations are used:
– ASIC Application-Specific Integrated Circuit
– ATA Advanced Technology Attachment
– Bels
– bpi
sound power units
bits per inch
– DA
– dB
Double Amplitude (represents pk-pk shaker displacement)
decibels
– dBA
– DPS
decibels, A weighted
Data Protection System
– ECC Error Correcting Code
– G/rms root means square
– Hz
hertz
– kfci
– KB
– LSB
– mA
– MB
thousands of flux changes per inch
kilobytes
Least Significant Bit
milliamperes
Megabytes (1 MB = 1,000,000 bytes when referring to disk
transfer rates or storage capacities and 1,048,576 bytes in all
other cases)
– Mb/s Megabits per second
– MB/s Megabytes per second
– MHz Megahertz
– ms
milliseconds
– MSB Most Significant Bit
– mV
– ns
millivolts
nanoseconds
Personal Computer
– PC
– SATA Serial ATA Interface
– tpi
– µs
– V
tracks per inch
microseconds
Volts
1-2
Maxtor DiamondMax 17 80-160GB AT Hard Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The typographical and naming conventions used in this manual are listed below.
Conventions that are unique to a specific table appear in the notes that follow that table.
Typographical Conventions
– Names of Bits: Bit names are presented in initial capitals. An example
is the Host Software Reset bit.
– Commands: Interface commands are listed in all capitals. An example
is WRITE LONG.
– Register Names: Registers are given in this manual with initial
capitals. An example is the Alternate Status Register.
– Parameters: Parameters are given as initial capitals when spelled out,
and are given as all capitals when abbreviated. Examples are Prefetch
Enable (PE), and Cache Enable (CE).
– Hexadecimal Notation: The hexadecimal notation is given in 9-point
subscript form. An example is 30H.
– Signal Negation: A signal name that is defined as active low is listed
with a minus sign following the signal. An example is RD–.
– Messages: A message that is sent from the drive to the host is listed in
all capitals. An example is ILLEGAL COMMAND.
Naming Conventions
– Host: In general, the system in which the drive resides is referred to as
the host.
– Computer Voice: This refers to items you type at the computer
keyboard. These items are listed in 10-point, all capitals, Courier font.
An example is FORMAT C:/S.
1.4
REFERENCES
For additional information about the ATA interface, refer to the latest revision of the
“1532D AT Attachment-7 with Packet Interface (ATA/ATAPI). For additional
information about the ATA interface, refer to the latest specifications on the internet
Maxtor DiamondMax 17 80-160GB AT Hard Drive
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1-4
Maxtor DiamondMax 17 80-160GB AT Hard Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
General Description
This chapter summarizes the general functions and key features of the DiamondMax
17 80-160GB AT hard disk drive, as well as the applicable standards and regulations.
2.1
PRODUCT OVERVIEW
Maxtor’s DiamondMax17 AT hard disk drives are part of a family of high
performance, 1-inch-high hard disk drives manufactured to meet the highest product
quality standards.These hard disk drives use nonremovable, 3 1/2-inch hard disks and
are available with the ATA interface.
The DiamondMax 17 AT hard disk drive features an embedded hard disk drive
controller, and uses ATA commands to optimize system performance. Because the
drive manages media defects and error recovery internally, these operations are fully
transparent to the user.
The innovative design of the DiamondMax 17 AT hard disk drive incorporates
leading edge technologies with transfer speeds up to 133MB/second, Advanced
Cache Management, Shock Protection System (SPS), Data Protection System (DPS),
Quiet Drive Technology (QDT), and Fly Height Adjust Technology. These
enhanced technologies enable Maxtor to produce a family of high-performance,
high-reliability drives.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
General Description
2.1
KEY FEATURES
The DiamondMax 17 AT hard disk drive includes the following key features:
General
– Low profile, 1-inch height
– Emulation of IBM® PC AT® task file register, and all AT fixed disk commands
– Windows NT2000, XP, Server, and Media Center Edition certification
Performance
– Average typical seek time of <12 ms for 80GB, <8.9 ms for 160GB
– Ultra ATA interface with Maxtor-patented Ultra ATA/133 protocol supporting
burst data transfer rates of 133MB/sec
– Average rotational latency of 4.17 ms
– 2MB (80GB) or 8MB (160GB) Cache buffer
– Look-ahead DisCache feature with continuous prefetch and WriteCache
write-buffering capabilities
– AutoTask Register update, Multi-block AutoRead, and Multi-block AutoWrite
features in a custom ASIC
– Read-on-arrival firmware
– Quadruple-burst ECC, and double burst ECC on-the-fly
– 1:1 interleave on read/write operations
– Support of all standard ATA data transfer modes with PIO mode 4 and
multiword DMA mode 2, and Ultra DMA modes 0, 1, 2, 3, 4, 5 and 6
– Adaptive cache segmentation
– FDB (Fluid Dynamic Bearing) Motors
– Fly Height Adjust Technology
Versatility
– Power saving modes
– Downloadable firmware
– Cable select feature
– Ability to daisy-chain two drives on the interface
2-2
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
General Description
Reliability
– 550k hours mean time expected until failure (MTTF)
– Automatic retry on read errors
– 320-bit, non-interleaved Reed-Solomon Error Correcting Code (ECC), with
cross checking correction up to fifteen separate bursts of 10 bits each totalling up
to 150 bits in length
– S.M.A.R.T. 4 (Self-Monitoring, Analysis and Reporting Technology)
– Transparent media defect mapping
– High performance, in-line defective sector skipping
– Reassignment of defective sectors discovered in the field, without reformatting
– Shock Protection System to reduce handling induced failures
– Data Protection System to verify drive integrity
– Quiet Drive Technology
2.1
REGULATORY COMPLIANCE STANDARDS
Maxtor Corporation’s disk drive products meet all domestic and international product
safety regulatory compliance requirements. Maxtor’s disk drive products conform to
the following specifically marked Product Safety Standards:
– Underwriters Laboratories (UL) Standard 1950. This certificate is a category
certification pertaining to all 3.5-inch series drives models.
– Canadian Standards Association (CSA) Standard C.22.2 No. 1950. This certificate
is a category certification pertaining to all 3.5-inch series drives.
– TUV Rheinland Standard EN60 950. This certificate is a category certification
pertaining to all 3.5-inch series drives models.
– Korean EMC certifications are issued by Radio Research laboratory (RPL), which
is organized under the Ministry of Information and Communications (MIC).
EMC testing includes electromagnetic emissions (EMI) and susceptibility (EMS).
Certified equipment is labeled with the MIC mark and certification number.
Product EMI/EMS Qualifications
– CE Mark authorization is granted by TUV Rheinland in compliance with our
qualifying under EN 55022:1994 and EN 50082-1:1997.
– C-Tick Mark is an Australian authorization marked noted on Maxtor’s disk drive
products. The mark proves conformity to the regulatory compliance document
AS/NZS 3548: 1995 and BS EN 55022: 1995.
– Maxtor’s disk drives are designed as a separate subassembly that conforms to the
FCC Rules for Radiated and Conducted emissions, Part 15 Subpart J; Class B
when installed in a given computer system.
– Approval from Taiwan BSMI. Number: D33019
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
General Description
2.1
HARDWARE REQUIREMENTS
The DiamondMax 17 AT hard disk drive is compatible with the IBM PC AT, and
other computers that are compatible with the IBM PC AT. It connects to the PC either
by means of a third-party ATA adapter board, or by plugging a cable from the drive
directly into a PC motherboard that supplies a ATA interface.
2-4
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Installation
This chapter explains how to unpack, configure, mount, and connect the Maxtor
DiamondMax 17 80-160GB AT hard disk drive prior to operation. It also explains
how to start up, format, and operate the drive.
3.1
SPACE REQUIREMENTS
Figure 3-1 shows the external dimensions of the DiamondMax 17 80-160GB AT
hard disk drive. For more information, please refer to Chapter 4 for detailed product
specifications.
Figure 3-1 Mechanical Dimensions
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.2
UNPACKING INSTRUCTIONS
CAUTION: The maximum limits for physical shock can be exceeded if the
drive is not handled properly. Special care should be taken not to
bump or drop the drive. It is highly recommended that the
DiamondMax 17 80-160GB AT hard drives are not stacked or
placed on any hard surface after they are unpacked. Such handling
could and will cause media damage.
CAUTION: During shipment and handling, the antistatic electrostatic dis-
charge (ESD) bag prevents electronic component damage due to
electrostatic discharge. To avoid accidental damage to the drive,
do not use a sharp instrument to open the ESD bag and do not
touch Printed Circuit Board components. Save the packing ma-
terials for possible future use.
1. Grounded wrist straps should be worn when opening the ESD bag.
2. Three layer runners should be installed on every table and bench where the
product is processed while still vulnerable to ESD.
3. Open the shipping container and remove the packing assembly that contains
the drive.
4. Remove the drive from the packing assembly.
5. Always handle the disk drive from the sides.
6. Do not touch the circuit board.
7. Never stack the disk drives on top of one another nor store them on their sides.
8. When you are ready to install the drive, remove it from the ESD bag.
3-2
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.3
HARDWARE OPTIONS
3.3.1
ATA Interface Connector
The configuration of a DiamondMax 17 80-160GB AT hard disk drive depends on
the host system in which it is to be installed. This section describes the hardware
options that you must take into account prior to installation.
Figure 3-3 Jumper Locations on the ATA Interface Connector
3-4
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The configuration of the following three jumpers controls the drive’s five modes of
operation:
– CS – Cable Select
– DS – Drive Select
– CLJ– Cylinder Limitation Jumper
The AT PCB has two jumper locations provided to configure the drive in a system.
The default configuration for the drive as shipped from the factory is with a jumper
across the CS location, and open positions in the DS and CLJ positions.
relative to pin 28 on the interface. 1 indicates that the specified jumper is installed;
0 indicates that the jumper is not installed.
Table 3-1 AT Jumper Options
CS
DS
Pin 28
DESCRIPTION
0
1
0
0
X
Drive is configured as a slave.
Gnd
Drive is configured as Master (Device 0) when attached to the end of a 80
conductor Ultra ATA cable.
0
1
1
0
X
Drive is configured as a Master.
Open
Drive is configured as a Slave (Device 1) when attached to the middle of a 80
conductor Ultra ATA cable.
1
1
X
Drive is configured as a Master with an attached slave that does not support
DASP.
cates that the jumper is installed, and an X indicates that the
jumper setting does not matter.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.3.1.1
Cable Select (CS) Jumper
When a DiamondMax 17 80-160GB AT hard disk drive and another ATA hard disk
drive are daisy-chained together, they can be configured as Master or Slave either
by the CS or DS jumpers. To configure the drive as a Master or Slave with the CS
feature, the CS jumper is installed (1). The drive's position on the 80 conductor
Ultra ATA data cable then determines whether the drive is a Master (Device 0) or
a Slave (Device 1). If the drive is connected to the end of the Ultra (cable Select)
data cable the drive is a Master. If the drive is connected to the middle connection
it is set as a Slave.
Once you install the CS jumper, the drive is configured as a Master or Slave by the
state of the Cable Select signal: pin 28 of the ATA bus connector. Please note that
pin 28 is a vendor-specific pin that Maxtor is using for a specific purpose. More than
one function is allocated to CS, according to the ATA CAM specification (see
reference to this specification in Chapter 1). If pin 28 is a 0 (grounded), the drive is
configured as a Master. If it is a 1 (high), the drive is configured as a Slave. In order
to configure two drives in a Master/Slave relationship using the CS jumper, you
need to use a cable that provides the proper signal level at pin 28 of the ATA bus
connector. This allows two drives to operate in a Master/Slave relationship
according to the drive cable placement.
The DiamondMax 17 80-160GB AT hard disk drives are shipped from the factory
as a Master (Device 0 - CS jumper installed). To configure a drive as a Slave (Device
1- DS scheme), the CS jumper must be removed. In this configuration, the spare
jumper removed from the CS position may be stored on the PK jumper pins.
3.3.1.2
3.3.1.3
Drive Select (DS) Jumper
You can also daisy-chain two drives on the ATA bus interface by using their Drive
Select (DS) jumpers. To use the DS feature, the CS jumper must not be installed.
To configure a drive as the Master (Device 0), a jumper must be installed on the DS pins.
Note: The order in which drives are connected in a daisy chain has no significance.
Master Jumper Configuration
In combination with the current DS or CS jumper settings, the Slave Present (SP)
jumper can be implemented if necessary as follows:
Note: The CS position doubles as the Slave present on this drive.
When the drive is configured as a Master (DS jumper installed or CS jumper
installed, and the Cable Select signal is set to (0), adding an additional jumper
(both jumpers DS and CS now installed) will indicate to the drive that a Slave
drive is present. This Master with Slave Present jumper configuration should
be installed on the Master drive only if the Slave drive does not use the Drive
Active/Slave Present (DASP–) signal to indicate its presence.
3-6
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.3.1.4
Cylinder Limitation Jumper (CLJ)
For user capacities below 66,055,248 sectors (32GB), inserting the CLJ jumper limits
the Number of Cylinders field 1 to a value of 16,383, as reported in IDENTIFY
DEVICE data word. This allows software drivers to determine that the actual
capacity is larger than indicated by the maximum CHS, requiring LBA addressing
to use the full capacity.
A summary of these effects for the DiamondMax 17 80-160GB AT drives is shown
in the following table:
CLJ Jumper Out
C=16,383
H=16
S=63
80GB
LBA = 156,301,488
C=16,383
H=16
S=63
160GB
LBA = 312,581,808
Table 3-2 LBA Addressing
Pin 1 of AT Connector
Pin 1
C
L
4.55±0.50
7.22±0.50
(to pin center)
29.78±0.50
Connector Side
(to pin center)
Figure 3-4 AT Connector and Jumper Location
3.3.2
ATA Bus Adapter
There are two ways you can configure a system to allow the DiamondMax 17
80-160GB AT hard disk drives to communicate over the ATA bus of an IBM
or IBM-compatible PC:
1. Connect the drive to a 40-pin ATA bus connector (if available) on the
motherboard of the PC.
2. Install an IDE-compatible adapter board in the PC, and connect the drive to
the adapter board.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.3.2.1
40-Pin ATA Bus Connector
Most PC motherboards have a built-in 40-pin ATA bus connector that is
compatible with the 40-pin ATA interface of the DiamondMax 17 80-160GB
AT hard disk drives. If the motherboard has an ATA connector, simply connect
a 40-pin ribbon cable between the drive and the motherboard.
You should also refer to the motherboard instruction manual to ensure signal
compatibility.
3.3.2.2
Adapter Board
If your PC motherboard does not contain a built-in 40-pin ATA bus interface
connector, you must install an ATA bus adapter board and connecting cable to allow
the drive to interface with the motherboard.
Please carefully read the instruction manual that comes with your adapter board, as
well as Chapter 5 of this manual to ensure signal compatibility between the adapter
board and the drive. Also, make sure that the adapter board jumper settings are
appropriate.
3-8
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.4
ATA BUS INTERFACE CONNECTOR (J1, SECTION C)
J1 is a three-in-one combination connector. The drive’s DC power can be applied to
section A. The ATA bus interface (40-pin) uses section C. The connector is mounted
on the back edge of the printed-circuit board (PCB), as shown in Figure 3-5.
Center
Key Slot
Pin 1
J1 IDE (40-Pin)/DC (4-Pin)
Combination Connector
4-Pin DC Power
40-Pin IDE
(J1 Section C)
Pin 1
(J1 Section A)
4
3
2
1
Pin 40
Figure 3-5 J1 DC Power and ATA Bus Combination Connector
3.4.1
DC Power (J1, Section A)
The recommended mating connectors for the +5 VDC and +12 VDC input power
are listed in Table 3-3.
Table 3-3 J1 Power Connector, Section A
Pin Number
Voltage Level
Mating Connector Type and Part Number (or equivalent)
J1 Section A (4-Pin):
1
2
3
4
+12 VDC
4-Pin Connector: AMP P/N 1-480424-0
Loose piece contacts: AMP P/N VS 60619-4
Strip contacts: AMP P/N VS 61117-4
Ground Return for +12 VDC
Ground Return for +5 VDC
+5 VDC
Note: Labels indicate the pin numbers on the connector. Pins 2 and 3 of section A
are the +5 and +12 volt returns and are connected together on the drive.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.4.2
3.4.3
External Drive Activity LED
An external drive activity LED may be connected to the DASP-I/O pin 39 on J1.
For more details, see the pin description in Table 5-1.
ATA Bus Interface Connector (J1, Section C)
On the DiamondMax 17 80-160GB AT hard disk drives, the ATA bus interface
cable connector (J1, section C) is a 40-pin Universal Header, as shown in Figure 3-5.
To prevent the possibility of incorrect installation, the connector has been keyed by
removing Pin 20. This ensures that a connector cannot be installed upside down.
See Chapter 5, “ATA Bus Interface and ATA Commands,” for more detailed
information about the required signals. Refer to Table 5-1 for the pin assignments
of the ATA bus connector (J1, section C).
3-10 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.5
MOUNTING
Orientation
3.5.1
The mounting holes on the DiamondMax 17 80-160GB AT hard disk drives allow
location of the three mounting holes on each side of the drive. The drive can also
be mounted using the four mounting hole locations on the PCB side of the drive.
Note: It is highly recommended that the drive is hard mounted on to the chassis
of the system being used for general operation, as well as for test purposes.
Failure to hard mount the drive can result in erroneous errors during testing.
Note: Drives can be mounted in any orientation. Normal position is with the PCB
facing down.
All dimensions are in millimeters. For mounting, #6-32 UNC screws are
recommended.
Figure 3-6 Mounting Dimensions
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Figure 3-7 Mounting Screw Clearance
CAUTION: The PCB is very close to the mounting holes. Do not ex-
ceed the specified length for the mounting screws. The
specified screw length allows full use of the mounting hole
threads, while avoiding damaging or placing unwanted stress
tween the PCB and the screws in the mounting holes. To
avoid stripping the mounting hole threads, the maximum
torque applied to the screws must not exceed 8 inch-pounds.
A maximum screw length of 0.25 inches may be used.
3-12 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.5.2
3.5.3
Clearance
Clearance from the drive to any other surface (except mounting surfaces) must be a
minimum of 1.25 mm (0.05 inches).
Ventilation
The DiamondMax 17 80-160GB AT hard disk drives operate without a cooling fan,
provided the base casting temperature as measured where the motor is attached to the
base does not exceed 140°F (60°C). Drive reliability and warranty will be limited if
the drive is exposed to temperatures greater than 60°C when operating and/or
temperatures greater than 70°C when in storage/not operating.
Figures 3-8 and 3-9 show airflow recommended for adequate cooling.Clearance from
the drive to any surface above and below the drive must be a minimum of 1.25mm.
Maxtor leaves the design and application of cooling and clearance for the disk drive
to the user, but the drive must maintain a case temperature at or below 60°C.
Figure 3-8 Lengthwise Airflow Cooling
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Figure 3-9 Crosswise Airflow Cooling
3.6
FOR SYSTEMS WITH AN ATA ADAPTER BOARD
To install the DiamondMax 17 80-160GB AT hard disk drive in an AT-compatible
system without a 40-pin ATA bus connector on its motherboard, you need a third-
party IDE-compatible adapter board.
3.6.1
Adapter Board Installation
Carefully read the manual that accompanies your adapter board before installing it.
Make sure that all the jumpers are set properly and that there are no address or signal
conflicts. You must also investigate to see if your AT-compatible system contains a
combination floppy and hard disk controller board. If it does, you must disable the
hard disk drive controller functions on that controller board before proceeding.
Once you have disabled the hard disk drive controller functions on the floppy/hard
drive controller, install the adapter board. Again, make sure that you have set all
jumper straps on the adapter board to avoid addressing and signal conflicts.
computer before installing the drive.
3-14 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.6.1.1
Connecting the Adapter Board and the Drive
Use a 40-pin cable to connect the drive to the board. See figure 3-10.
To connect the drive to the board:
1. Insert the 40-pin cable connector into the mating connector of the adapter
board. Make sure that pin 1 of the connector matches with pin 1 on the cable.
2. Insert the other end of the cable into the header on the drive. When inserting
this end of the cable, make sure that pin 1 of the cable connects to pin 1 of the
drive connector.
3. Secure the drive to the system chassis by using the mounting screws.
Figure 3-10 Drive Power Supply and ATA Bus Interface Cables
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.7
TECHNIQUES IN DRIVE CONFIGURATION
The 8.4-Gigabytes Barrier
3.7.1
Newer BIOS’s allow users to configure disk drives to go beyond the 528MB barrier
by using several BIOS translation schemes. However, while using these translations
the BIOS using Int 13 functions are limited to 24 bits of addressing which results in
another barrier at the 8.4GB capacity.
To overcome this barrier a new set of Int 13 extensions are being implemented by
most BIOS manufacturers. The new Int 13 extension allows for four words of
addressing space (64 bits) resulting in 9.4 Terrabytes of accessible space.
Whenever possible the DiamondMax 17 80-160GB AT drive should be used on
systems with BIOS that support Int 13 extensions. If that is not possible the
following are some techniques that can be used to overcome this barrier:
– Use a third party software that supplements the BIOS and adds Int 13
extension support.
– Obtain a BIOS upgrade from the system board manufacturer. Many system
board manufacturers allow their BIOS to be upgraded in the field using
special download utilities. Information on BIOS upgrades can be obtained on
the System Board Customer Service respective web sites on the Internet.
– Insert the Cylinder Limitation Jumper (CLJ) on the drive (see Section 3.3.1.4).
3.7.2
Operating System Limitations
Most popular operating systems available today have additional limitations which
affect the use of large capacity drives. However, these limitations can not be
corrected on the BIOS and it is up to the operating system manufacturers to release
improved versions to address these problems.
DOS and Windows 95 use a File Allocation Table (FAT) size of 16 bits which will only
support partitions up to 2.1 GB. Windows 95 OSR2, Windows 98, and Windows ME
use a FAT size of 32 bits, allowing partitions of up to 2.2 terrabytes. Windows NT,
2000, and XP Use NTFS, which allows partition sizes up to 16 terrabytes.
3-16 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3.8
SYSTEM STARTUP AND OPERATION
Once you have installed the DiamondMax 17 80-160GB AT hard disk drive, and
adapter board (if required) in the host system, you are ready to partition and format
the drive for operation. To set up the drive correctly, follow these steps:
1. Power on the system.
2. Run the SETUP program. This is generally on a Diagnostics or Utilities disk,
or within the system’s BIOS. Some system BIOS have an auto-detecting
feature making SETUP unnecessary.
3. Enter the appropriate parameters.
Note: The SETUP program allows you to enter the types of optional hardware in-
stalled—such as the hard disk drive type, the floppy disk drive capacity, and
the display adapter type. The system’s BIOS uses this information to initialize
the system when the power is switched on. For instructions on how to use
the SETUP program, refer to the system manual for your PC.
Note: During the AT system CMOS setup, you must enter the drive type for the
DiamondMax 17 80-160GB AT hard disk drives. The drive supports the
translation of its physical drive geometry parameters such as cylinders, heads,
and sectors per track to a logical addressing mode. The drive can work with
different BIOS drive-type tables of the various host systems.
Note: You can choose any drive type that does not exceed the capacity of the drive.
the DiamondMax 17 80-160GB AT family of hard disk drives.
Table 3-4 Logical Addressing Format
Model
Interface
CYL
HD
SPT
Max LBA
Capacity
6G080L0
6G160P0
ATA/133
ATA/133
16,383
16,383
16
16
63
63
156,301,488
312,581,808
80GB
160GB
4. Boot the system using the operating system installation disk—for example, MS-
DOS—then follow the installation instructions in the operating system manual.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Product Specifications
4.1
4.2
MODEL NUMBER AND CAPACITY
Model
6G080L0
80GB
6G160P0
Formatted Capacity
(GB LBA Mode)
160GB
GB means 1 billion bytes. Total accessible capacity varies
depending on operating environment.
DRIVE CONFIGURATION
Model
6G080L0
6G160P0
156,301,488
312,581,808
Sectors per Drive (max LBA)
Integrated Interface
Maxtor Ultra ATA/133
(ATA-5/ATA-6/ATA-7)
Recording Method
Servo Type
RLL EEPR4
Embedded
192
Number of Servo Sectors
Data Zones per Surface
Data Sectors per Track (ID / OD)
Areal Density
16
645 / 1224
75 / 60.8
2
(Gbits/in max, ID / OD)
Flux Density (kfci, ID / OD)
Recording Density (kbpi, ID / OD)
Track Density (ktpi)
430 / 378
705 / 630
139.7
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
4.3
PERFORMANCE SPECIFICATIONS
Model
6G080L0
6G160P0
Seek Times (typical read, ms)
Track-to-Track
2.5
23
Typical Seek
< 12
< 8.9
Full Stroke (normal seek)
Average Latency (ms)
Controller Overhead (ms)
Rotation Speed (RPM 0.1%)
Data Transfer Speed (MB/sec, max)
To/From Interface
4.18
< 0.3
7,200
133
To/From Media
333 / 619
(ID / OD up to nn.n, where nn.n
is the maximum possible
transfer rate)
Sustained
30.8 / 58.9
(ID / OD up to nn.n, where nn.n
is the maximum transfer rate
possible)
Data Buffer Size (MB)
2
8
Drive Ready Time (sec, typical)
< 8.0
4.4
PHYSICAL DIMENSIONS
Parameter
Value
Height (mm, maximum)
Width (mm, typical)
26.1
101.6 0.25
146.1 0.25
Depth (mm, maximum)
Weight (g, maximum)
80GB = 455 / 160GB = 460
4-2
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
4.5
POWER REQUIREMENTS – 80GB & 160GB
Power
(Watts)
Current
12V (mA)
Current
5V (mA)
Mode
Start-up (peak) over 1 ms
Seek (peak) over 1 ms*
23
19.5
7.5
7
1580
1400
255
255
600
465
255
240
15
775
530
850
795
445
480
440
220
220
220
Sequential Write (average)
Sequential Read (average)
Random Seek (average)*
Random Read / Write (average)*
Idle Average, no R/W activity
Idle Active, low power/head on ramp
Standby (average)
9.5
8
5.5
4
1.3
1.3
Sleep (average)
15
* Acoustic management in performace mode; quiet modes reduce 12V current.
4.5.1
Voltage Tolerance
Voltage Tolerance
5V 5%
12V 10%
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
4.6
POWER MODE DEFINITIONS
Start-up
The drive is spinning up following initial application of power and has not yet
reached full speed.
Seek
A random access operation by the drive.
Read/Write
Data is being read from or written to the drive.
Idle
The drive is spinning, the actuator is parked and powered off and all other circuitry
is powered on. The drive is capable of responding to read commands within 40 ms.
Standby
The motor is not spinning. The drive will leave this mode upon receipt of a
command that requires disk access. The time-out value for this mode is
programmable. The buffer is active to accept write data.
Sleep
This is the lowest power state – with the interface set to inactive. A software or
hardware reset is required to return the drive to the Standby state.
4.7
EPA ENERGY STAR COMPLIANCE
Maxtor Corporation supports the goals of the U.S. Environmental Protection
Agency’s Energy Star program to reduce the electrical power consumption of
computer equipment.
4-4
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
4.8
ENVIRONMENTAL LIMITS
Parameter
Operating
Non-Operating/Storage
Temperature
0°C to 60°C
(base casting at motor hub)
-40° to 70°C per Mil-STD-
810E, method 501.3, climatic
category: hot induced
conditions.
Thermal Gradient
Relative Humidity
Wet Bulb
20°C per hour (maximum)
30°C per hour (maximum)
5% to 95% (non-condensing)
37.7°C (maximum)
40°C (maximum)
Altitude (relative to sea level)
-650 to 10,000 feet
-650 to 40,000 feet
Acoustics
80GB
160GB
(1 disk)
(1disk)
2.5 / 2.6
2.6 / 2.7
3.1 / 3.3
Idle (typical / maximum): Bels
2.5 / 2.6
Quiet Seek (typical / maximum): Bels
2.6 / 2.7
3.1 / 3.3
Performance Seek (typical / maximum): Bels
Notes:
1. Margin demonstrated implies the product will operate at the stated conditions
with an acceptable impact to the ARR specification for any OEM requiring
those values in their purchase specification.
2. The testing performed by Maxtor is consistent with ISO 7779. Variation in
acoustic levels from the idle specification may occur due to offline activity
according to the SMART specification and/or atmospheric conditions.
3. Above 1,000 feet (305 meters), the maximum temperature is derated
linearly to 112°F (44°C) at 10,000 feet (3,048 meters).
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
4.9
SHOCK AND VIBRATION
Parameter
Operating
Non-Operating
Mechanical Shock
1/2 sine
2 ms, R = 0.988 @ 65 Gs
2 ms, R = 0.90 @ > 350G
1 ms, R = 0.95 @ > 200G
.5 ms, R = 0.99 @ > 200G
Rotational Linear Vibration
1/2 sine, radians / sec
2 ms, 2k
1 ms, 25k
2
Linear Random Vibration (G rms)
10 – 500 Hz, 0.86
7 – 800 Hz, 3.08
4.10
RELIABILITY SPECIFICATIONS
Annualized Return Rate
< 1%
Annualized Return Rate (ARR) indicates the average against products shipped.
ARR includes all reasons for returns (failures, handling, damage, NDF) but does not
include inventory credit returns.
Load/Unload Cycles
> 600K
This indicates the average minimum cycles for reliable unload and load of head ramp
(where heads are loaded and parked onto a ramp off the disk when not in use).
Data Reliability
< 1 per 1015 bits read
Data errors (non-recoverable). Average data error rate allowed with all error
recovery features activated.
Component Design Life
5 years (minimum)
Component design life is defined as:
a.) the time period before identified wear-out mechanisms impact the failure rate,
or
b.) the time period up to the wear-out point when useful component life expires.
4-6
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
4.11
EMC/EMI
4.11.1
Radiated Electromagnetic Field Emissions - EMC Compliance
The hard disk drive mechanism is designed as a subassembly for installation into a
suitable enclosure and is therefore not subject to Subpart J of Part 15 of FCC Rules
(47CFR15) or the Canadian Department of Communications Radio Interference
Regulations. Although not required, the disk mechanism has been tested within a
suitable end-use product and found to comply with Class B limits of the FCC Rules
and Regulations of the Canadian Department of Communications.
The CE Marking indicates conformity with the European Union Low Voltage
Directive (73/23/EEC) when the disk mechanism is installed in a typical personal
computer. Maxtor recommends that testing and analysis for EMC compliance be
performed with the disk mechanism installed within the user's end-use application.
4.11.2
Canadian Emissions Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus as set out in the radio interference regulations of the Canadian
department of communications.
Le present appareil numerique n'emet pas de bruit radioelectriques depassant les
limites applicables aux appareils numeriques de Class B prescrites dans le reglement
sur le brouillage radioelectrique edicte pa le ministere des communications du
Canada.
4.12
SAFETY REGULATORY COMPLIANCE
All Maxtor hard drives comply with relevant product safety standards such as CE,
CUL, TUV and UL rules and regulations. As delivered, Maxtor hard drives are
designed for system integration before they are used.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
4-8
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
ATA Bus Interface and ATA Commands
This chapter describes the interface between the DiamondMax 17 80-160GB AT
hard disk drive and the ATA bus. The commands that are issued from the host to
control the drive are listed, as well as the electrical and mechanical characteristics of
the interface.
5.1
INTRODUCTION
The Maxtor DiamondMax 17 80-160GB AT hard disk drive uses the standard
ATA/ATAPI-7 interface. Support of various options in the standard are explained
in the following sections.
5.2
MECHANICAL INTERFACE
5.2.1
Signal Cable and Connector
The Maxtor DiamondMax 17 hard disk drive contains a 40-pin unitized connector
for both signal and power connections as well as configuration jumpers. The
dimensions and specifications of the unitized connector comply with Annex. A in
the ATA/ATAPI standard.The Maxtor DiamondMax 17 drives require the use of
an 80 conductor cable (ATA/ATAPI-6, Annex. A, Figure A.4 and description) to
support the drive’s Ultra DMA capability.
5.3
ELECTRICAL INTERFACE
ATA Bus Interface
5.3.1
5.3.1.1
Electrical Characteristics
Signals on the ATA interface are assigned to connector pins according to Annex. A in the
ATA/ATAPI-6 standard for the 80 conductor cable assembly. The signaling protocol
complies with clause 9 and signal timing complies with clause 10 of the standard.
The Maxtor DiamondMax 17 hard disk drives support all Ultra DMA Data Transfer
modes (0 - 5) defined in the ATA/ATAPI-6 standard. In addition, these drives
support Mode 6, and can send and receive data at the full 133MB/s transfer rate.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
5.4
REGISTER ADDRESS DECODING
The Maxtor DiamondMax 17 80-160GB AT hard disk drive allow their host
systems to address the full set of command and control registers as specified in clause
5 of the ATA/ATAPI-7 standard.
5.5
COMMAND INTERFACE
5.5.1
General Feature Set
The µProcessor, Disk Controller, and ATA Interface electronics are contained in a
proprietary ASIC developed by Maxtor.
5.5.2
Supported Commands
The Maxtor DiamondMax 17 80-160GB AT hard disk drive supports all the
mandatory commands from the general feature set for devices not supporting the
Packet command feature set. Table 5-1 lists the supported commands. Refer to the
ATA/ATAPI-7 standard for a detailed description of these commands. The
IDENTIFY DRIVE command, however, is elaborated in the section "Identify
1. As defined in the ATA/ATAPI-7 standard.
Feature Register
Command
Command Code
Value(s)
CHECK POWER MODE
DEVICE CONFIGURATION FREEZE LOCK
DEVICE CONFIGURATION IDENTIFY
DEVICE CONFIGURATION RESTORE
DEVICE CONFIGURATION SET
DOWNLOAD MICROCODE
EXECUTE DRIVE DIAGNOSTIC
FLUSH CACHE
98h, E5h
B1h
C1h
C2h
B1h
B1h
C0h
B1h
C3h
92h
07h, 01h
90h
E7h
FLUSH CACHE EXTENSION
IDENTIFY DEVICE
EAh
ECh
IDLE
97h, E3h
95h, E1h
00h
IDLE IMMEDIATE
NOP
READ BUFFER
E4h
READ DMA
C8h, C9h
25h
READ DMA EXTENSION
Table 5-1 Supported Commands
5-2
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Feature Register
Command Code
Command
Value(s)
READ FPDMA QUEUED
READ LOG EXTENSION
60h
2fh
READ MULTIPLE
C4h
READ MULTIPLE EXTENSION
READ NATIVE MAX ADDRESS
READ NATIVE MAX ADDRESS EXTENSION
READ SECTOR(S)
29h
F8h
27h
20h, 21h
24h
READ SECTOR(S) EXTENSION
READ VERIFY SECTOR(S)
READ VERIFY SECTOR(S) EXTENSION
SECURITY DISABLE PASSWORD
SECURITY ERASE PREPARE
SECURITY ERASE UNIT
SECURITY FREEZE LOCK
SECURITY SET PASSWORD
SECURITY UNLOCK
40h, 41h
42h
F6h
F3h
F4h
F5h
F1h
F2h
SEEK
70h
SET FEATURES
EFh
F9h
Note 1
00h
SET MAX ADDRESS
SET MAX ADDRESS EXTENSION
SET MAX SET PASSWORD
SET MAX LOCK
37h
00h
F9h
01h
F9h
02h
SET MAX UNLOCK
F9h
03h
SET MAX FREEZE LOCK
SET MULTIPLE MODE
F9h
04h
C6h
SLEEP
99h, E6h
B0h
B0h
B0h
B0h
B0h
B0h
B0h
SMART DISABLE OPERATIONS
SMART ENABLE OPERATIONS
SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE
SMART EXECUTE OFF-LINE IMMEDIATE
SMART READ DATA
D9h
D8h
D2h
D4h
D0h
D5h
DAh
SMART READ LOG
SMART RETURN STATUS
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Feature Register
Value(s)
Command
Command Code
SMART SAVE ATTRIBUTE VALUES
B0h
B0h
D3h
D6h
SMART WRITE LOG
STANDBY
96h, E2h
94h, E0h
E8h
STANDBY IMMEDIATE
WRITE BUFFER
WRITE DMA
CAh, CBh
35h
WRITE DMA EXTENSION
WRITE DMA FUA EXTENSION
WRITE FPDMA QUEUED
WRITE LOG EXTENSION
WRITE MULTIPLE
30h
61h
3fh
C5h
WRITE MULTIPLE EXTENSION
WRITE MULTIPLE FUA EXTENSION
WRITE SECTOR(S)
39h
CEh
30h, 31h
34h
WRITE SECTOR(S) EXTENSION
5-4
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
5.5.3
Identify Drive Command
This command allows the host to receive parameter information from the drive.
When the command is received, the drive:
1. Sets BSY
2. Stores the required parameter information in the sector buffer
3. Sets the DRQ bit
4. Generates an interrupt
The host may then read the information out of the sector buffer. Parameter words
in the buffer are shown in Table 5-2.
Note: All reserved bits or words should be zeroes.
Table 5-2 Identify Drive Command Parameters
Word
Content Description
0
General configuration bit-significant information:
15:
0 = ATA device
Retired
14-8:
7:
1 = removable media device
Obsolete
6:
5-3:
Retired
2:
Response incomplete
Retired
1:
0:
Reserved
1
2
Obsolete
Specific configuration
3
Obsolete
4-5
6
Retired
Obsolete
7-8
9
Reserved for assignment by the CompactFlash Association
Retired
10-19
20-21
22
Serial number (20 ASCII characters)
Retired
Reserved
23-26
27-46
Firmware revision (8 ASCII characters)
Model number (40 ASCII characters)
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
47
15-8:
7-0:
80h
00h = Reserved
01h-FFh: = Maximum number of sectors that shall be transferred per interrupt on READ/
WRITE MULTIPLE commands
48
49
Reserved
Capabilities
15-14: Reserved for the IDENTIFY PACKET DEVICE command.
13:
1 = Standby timer values as specified in this standard are supported.
0 = Standby timer values shall be managed by the device
12:
11:
10:
9:
Reserved for the IDENTIFY PACKET DEVICE command.
1 = IORDY supported. 0 = IORDY may be supported
1 = IORDY may be disabled
1 = LBA supported
8:
1 = DMA supported.
7-0:
Retired
50
Capabilities
15:
Shall be cleared to zero.
14:
Shall be set to one.
13-2:
1:
Reserved.
Obsolete
0:
Shall be set to one to indicate a device specific Standby timer value minimum.
51-52
Obsolete
5-6
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
53
15-3:
2:
Reserved
1 = the fields reported in word 88 are valid.
0 = the fields reported in word 88 are not valid
1:
1 = the fields reported in words (70:64) are valid.
0 = the fields reported in words (70:64) are not valid
0:
Obsolete
54-58
59
Obsolete
15-9:
8:
Reserved
1 = Multiple sector setting is valid
7-0:
xxh = Current setting for number of sectors that shall be transferred per interrupt
on R/W Multiple command
Total number of user addressable sectors
Obsolete
60-61
62
63
15-11: Reserved
10:
1 = Multiword DMA mode 2 is selected.
0 = Multiword DMA mode 2 is not selected
9:
1 = Multiword DMA mode 1 is selected.
0 = Multiword DMA mode 1 is not selected
8:
1 = Multiword DMA mode 0 is selected.
0 = Multiword DMA mode 0 is not selected
7-3:
2:
Reserved
1 = Multiword DMA mode 2 and below are supported
1 = Multiword DMA mode 1 and below are supported
1 = Multiword DMA mode 0 is supported
Reserved
1:
0:
64
65
66
67
15-8:
7-0:
PIO modes supported
Minimum Multiword DMA transfer cycle time per word
15-0: Cycle time in nanoseconds
Manufacturer’s recommended Multiword DMA transfer cycle time
15-0: Cycle time in nanoseconds
Minimum PIO transfer cycle time without flow control
15-0: Cycle time in nanoseconds
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
Minimum PIO transfer cycle time with IORDY flow control
15-0: Cycle time in nanoseconds
68
69-70
71-74
75
Reserved (for future command overlap and queuing)
Reserved for IDENTIFY PACKET DEVICE command.
Queue depth
15-5:
4-0:
Reserved
Maximum queue depth – 1
76-79
80
Reserved for Serial ATA
Major version number
0000h or FFFFh = device does not report version
15:
14:
13:
12:
11:
10:
9:
Reserved
Reserved for ATA/ATAPI-14
Reserved for ATA/ATAPI-13
Reserved for ATA/ATAPI-12
Reserved for ATA/ATAPI-11
Reserved for ATA/ATAPI-10
Reserved for ATA/ATAPI-9
Reserved for ATA/ATAPI-8
Reserved for ATA/ATAPI-7
1 = supports ATA/ATAPI-6
1 = supports ATA/ATAPI-5
1 = supports ATA/ATAPI-4
1 = supports ATA-3
8:
7:
6:
5:
4:
3:
2:
Obsolete
1:
Obsolete
0:
Reserved
5-8
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
81
Minor version number
0000h or FFFFh = device does not report version.
0001h-FFFEh = see 6.16.41 of ATA/ATAPI-7 specification
82
Command set supported.
15:
14:
13:
12:
11:
10:
9:
Obsolete
1 = NOP command supported
1 = READ BUFFER command supported
1 = WRITE BUFFER command supported
Obsolete
1 = Host Protected Area feature set supported
1 = DEVICE RESET command supported
1 = SERVICE interrupt supported
1 = release interrupt supported
1 = look-ahead supported
8:
7:
6:
5:
1 = write cache supported
4:
Shall be cleared to zero to indicate that the PACKET Command feature set is not
supported
3:
2:
1:
0:
1 = mandatory Power Management feature set supported
1 = Removable Media feature set supported
1 = Security Mode feature set supported
1 = SMART feature set supported
83
Command sets supported.
15:
14:
13:
12:
11:
10:
9:
Shall be cleared to zero
Shall be set to on
1 = FLUSH CACHE EXT command supported
1 = mandatory FLUSH CACHE command supported
1 = Device Configuration Overlay feature set supported
1 = 48-bit Address feature set supported
1 = Automatic Acoustic Management feature set supported
1 = SET MAX security extension supported
8:
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
83
7:
6:
5:
4:
3:
2:
1:
0:
See Address Offset Reserved Area Boot, INCITS TR27:2001
1 = SET FEATURES subcommand required to spinup after power-up
1 = Power-Up In Standby feature set supported
1 = Removable Media Status Notification feature set supported
1 = Advanced Power Management feature set supported
1 = CFA feature set supported
1 = READ/WRITE DMA QUEUED supported
1 = DOWNLOAD MICROCODE command supported
84
Command set/feature supported extension.
15:
14:
13-8:
7:
Shall be cleared to zero
Shall be set to one
Reserved
1 = WRITE DMA QUEUED FUA EXT command supported
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands supported
1 = General Purpose Logging feature set supported
1 = Streaming feature set supported
1 = Media Card Pass Through Command feature set supported
1 = Media serial number supported
6:
5:
4:
3:
2:
1:
1 = SMART self-test supported
0:
1 = SMART error logging supported
85
Command set/feature enabled.
15:
14:
13:
12:
11:
10:
9:
Obsolete
1 = NOP command enabled
1 = READ BUFFER command enabled
1 = WRITE BUFFER command enabled
Obsolete
1 = Host Protected Area feature set enabled
1 = DEVICE RESET command enabled
1 = SERVICE interrupt enabled
8:
5-10 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
1 = release interrupt enabled
85
7:
6:
5:
4:
1 = look-ahead enabled
1 = write cache enabled
Shall be cleared to zero to indicate that the PACKET Command feature set is not
supported.
3:
2:
1:
0:
1 = Power Management feature set enabled
1 = Removable Media feature set enabled
1 = Security Mode feature set enabled
1 = SMART feature set enabled
86
Command set/feature enabled.
15-14: Reserved
13:
12:
11:
10:
9:
1 = FLUSH CACHE EXT command supported
1 = FLUSH CACHE command supported
1 = Device Configuration Overlay supported
1 = 48-bit Address features set supported
1 = Automatic Acoustic Management feature set enabled
1 = SET MAX security extension enabled by SET MAX SET PASSWORD
See Address Offset Reserved Area Boot, INCITS TR27:2001
1 = SET FEATURES subcommand required to spin-up after power-up
1 = Power-Up In Standby feature set enabled
8:
7:
6:
5:
4:
1 = Removable Media Status Notification feature set enabled
1 = Advanced Power Management feature set enabled
1 = CFA feature set enabled
3:
2:
1:
1 = READ/WRITE DMA QUEUED command supported
1 = DOWNLOAD MICROCODE command supported
0:
87
Command set/feature default.
15:
14:
13-8:
7:
Shall be cleared to zero
Shall be set to one
Reserved
1 = WRITE DMA QUEUED FUA EXT command supported
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
87
6:
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands supported
General Purpose Logging feature set supported
1 = Valid CONFIGURE STREAM command has been executed
1 = Media Card Pass Through Command feature set enabled
1 = Media serial number is valid
5:
4:
3:
2:
1:
1 = SMART self-test supported
0:
1 = SMART error logging supported
88
15:
14:
13:
12:
11:
10:
9:
Reserved
1 = Ultra DMA mode 6 is selected. 0 = Ultra DMA mode 6 is not selected
1 = Ultra DMA mode 5 is selected. 0 = Ultra DMA mode 5 is not selected
1 = Ultra DMA mode 4 is selected. 0 = Ultra DMA mode 4 is not selected
1 = Ultra DMA mode 3 is selected. 0 = Ultra DMA mode 3 is not selected
1 = Ultra DMA mode 2 is selected. 0 = Ultra DMA mode 2 is not selected
1 = Ultra DMA mode 1 is selected. 0 = Ultra DMA mode 1 is not selected
1 = Ultra DMA mode 0 is selected. 0 = Ultra DMA mode 0 is not selected
Reserved
8:
7:
6:
1 = Ultra DMA mode 6 and below are supported
1 = Ultra DMA mode 5 and below are supported
1 = Ultra DMA mode 4 and below are supported
1 = Ultra DMA mode 3 and below are supported
1 = Ultra DMA mode 2 and below are supported
1 = Ultra DMA mode 1 and below are supported
1 = Ultra DMA mode 0 is supported
5:
4:
3:
2:
1:
0:
89
90
91
92
Time required for security erase unit completion
Time required for Enhanced security erase completion
Current advanced power management value
Master Password Revision Code
5-12 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
93
Hardware reset result. The contents of bits (12:0) of this word shall change only during the
execution of a hardware reset
15:
Shall be cleared to zero.
14:
Shall be set to one.
13:
1 = device detected CBLID- above ViH. 0 = device detected CBLID- below ViL
12-8:
Device 1 hardware reset result. Device 0 shall clear these bits to zero. Device shall
set these bits as follows:
12: Reserved.
11: 0 = Device 1 did not assert PDIAG-.
1 = Device 1 asserted PDIAG-.
10-9: These bits indicate how Device 1 determined the device number:
00 = Reserved.
01 = a jumper was used.
10 = the CSEL signal was used.
11 = some other method was used or the method is unknown.
8: Shall be set to one.
7-0:
Device 0 hardware reset result. Device 1 shall clear these bits to zero. Device shall
set these bits as follows:
7: Reserved.
6: 0 = Device 0 does not respond when Device 1 is selected.
1 = Device 0 responds when Device 1 is selected.
5: 0 = Device 0 did not detect the assertion of DASP-.
1 = Device 0 detected the assertion of DASP-
4: 0 = Device 0 did not detect the assertion of PDIAG-.
1 = Device 0 detected the assertion of PDIAG-.
3:0 = Device 0 failed diagnostics.
1 = Device 0 passed diagnostics.
2-1: These bits indicate how Device 0 determined the device number:
00 = Reserved.
01 = a jumper was used.
10 = the CSEL signal was used.
11 = some other method was used or the method is unknown.
0: Shall be set to one.
94
15-8:
7-0:
Vendor’s recommended acoustic management value.
Current automatic acoustic management value
95
96
Stream Minimum Request Size
Stream Transfer Time - DMA
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
97
98-99
100-103
104
Stream Access Latency - DMA
Streaming Performance Granularity
Maximum user LBA for 48-bit Address feature set.
Stream Transfer Time – PIO
105
Stream Access Latency – PIO
Physical sector size
106
15:
Shall be cleared to zero
14:
Shall be set to one
13:
1 = Device has multiple logical sectors per physical sector.
Reserved
12-4:
3-0:
X
2 logical sectors per physical sector
107
108-126
127
Inter-seek delay for ISO-7779 acoustic testing in microseconds
Reserved
Removable Media Status Notification feature set support
15-2:
1-0:
Reserved
00 = Removable Media Status Notification feature set not supported
01 = Removable Media Status Notification feature supported
10 = Reserved
11 = Reserved
5-14 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
Word
Content Description
128
Security status
15-9:
8:
Reserved
Security level 0 = High, 1 = Maximum
7-6:
5:
Reserved
1 = Enhanced security erase supported
1 = Security count expired
1 = Security frozen
4:
3:
2:
1 = Security locked
1:
1 = Security enabled
1 = Security supported
0:
129-159
160-254
255
Vendor specific
Reserved
Integrity word
15-8:
7-0:
Checksum
Signature
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
ATA Bus Interface and ATA Commands
5-16 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Service and Support
6.1
GETTING HELP
Before contacting Maxtor Support, use the Hard Disk Information feature in
MaxBlast to view the model number and serial number of your drive. These numbers
can be used to get help from Maxtor Support, register your drive, and look up
information on the Maxtor website.
such as:
• Warranty Services
– Drive returns, Warranty Status, Limited Warranty Statement
• Product Support
– Installation Tutorials, Specifications, Jumper Settings, Installation Guides,
Product Manuals
• Software Downloads
– Installation Software, Utilities, Diagnostics
• Knowledge Base
– Troubleshooting information, FAQs, resolved problem database
• Product Index
– Current and Legacy Maxtor product’s listing
Click on Worldwide Support to access the Knowledge Base, download software
updates, register your drive, and get assistance via e-mail.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Service and Support
6-2
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
BLOCK – A sector or group of sectors.
A
ACCESS– (v) Read, write, or update information on some
storage medium, such as a disk. (n) One of these operations.
BPI – Abbreviation for bits per inch. A measure of how
densely information is packed on a storage medium. Flux
changes per inch is also a term commonly used in describing
storage density on a magnetic surface.
ACCESS TIME – The interval between the time a request
for data is made by the system and the time the data is
available from the drive. Access time includes the actual seek
time, rotational latency, and command processing overhead
time. See also seek, rotational latency, and overhead.
BUFFER – An area of RAM reserved for temporary
storage of data that is waiting to be sent to a device that is
not yet ready to receive it. The data is usually on its way to
or from the disk drive or some other peripheral device.
ACTUATOR – Also known as the positioner. The internal
mechanism that moves the read/write head to the proper
track. The Maxtor actuator consists of a rotary voice coil and
the head mounting arms. One end of each head mounting
arm attaches to the rotor with the read/write heads attached
at the opposite end of each arm. As current is applied to the
rotor, it rotates, positioning the heads over the desired
cylinder on the media.
BUS – The part of a chip, circuit board, or interface
designed to send and receive data.
BYTE– The basic unit of computer memory, large enough
to hold one character of alphanumeric data. Comprised of
eight bits. See also bit.
C
ALLOCATION – The process of assigning particular areas
of the disk to particular files. See also allocation unit.
CACHE – Random-access memory used as a buffer
between the CPU and a hard disk. Information more likely
to be read or changed is placed in the cache, where it can be
accessed more quickly to speed up general data flow.
ALLOCATION UNIT – An allocation unit, also known
as a cluster, is a group of sectors on the disk that can be
reserved for the use of a particular file.
CAPACITY – The amount of information that can be
stored on a disk drive. The data is stored in bytes, and
capacity is usually expressed in megabytes.
AVERAGE SEEK TIME – The average time it takes for
the read/write head to move to a specific location. To
compute the average seek time, you divide the time it takes
to complete a large number of random seeks all over the disk
by the number of seeks performed.
CDB – Command Descriptor Block. The SCSI structure
used to communicate requests from an initiator (system) to
a target (drive).
B
CLEAN ROOM – An environmentally controlled
dust-free assembly or repair facility in which hard disk drives
are assembled or can be opened for internal servicing.
BACKUP – A copy of a file, directory, or volume on a
separate storage device from the original, for the purpose of
retrieval in case the original is accidentally erased, damaged,
or destroyed.
CLUSTER – A group of sectors on a disk drive that is
addressed as one logical unit by the operating system.
BAD BLOCK – A block (usually the size of a sector) that
cannot reliably hold data because of a media flaw or
damaged format markings.
CONTROLLER – Short form of disk controller. The chip
or complete circuit that translates computer data and
commands.
BAD TRACK TABLE – A label affixed to the casing of a
hard disk drive that tells which tracks are flawed and cannot
hold data. The listing is typed into the low-level formatting
program when the drive is being installed. Because Maxtor
disk drive’s defect-management scheme handles all such
flaws automatically, there is no need to concern yourself
with bad track tables.
CONTROLLER CARD – An adapter holding the
control electronics for one or more hard disks, usually
installed in a slot in the computer.
CPU – Acronym for Central Processing Unit. The
microprocessor chip that performs the bulk of data
processing in a computer.
BIT – Abbreviation for binary digit. A binary digit may
have one of two values—1 or 0. This contrasts with a
decimal digit, which may have a value from 0 to 9. A bit is
one of the logic 1or logic 0 binary settings that make up a
byte of data. See also byte.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
G-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
CRC – Acronym for Cyclic Redundancy Check. An error
detection code that is recorded within each sector and is
used to see whether parts of a string of data are missing or
erroneous.
E
ECC – Acronym for error correction code. The recording of
extra verifying information encoded along with the disk
data. The controller uses the extra information to check for
data errors, and corrects the errors when possible.
CYLINDER – On a disk drive that has more than one
recording surface and heads that move to various tracks, the
group of all tracks located at a given head position. The
number of cylinders times the number of heads equals the
number of tracks per drive.
EMBEDDED SERVO – A timing or location signal
placed on the disk’s surface on the tracks that also store data.
These signals allow the actuator to fine-tune the position of
the read/write heads.
D
ENCODING – The protocol by which particular data
patterns are changed prior to being written on the disk
surface as a pattern of On and Off or 1 and 0 signals.
DATA SEPARATOR – On a disk drive that stores data
and timing information in an encoded form, the circuit that
extracts the data from the combined data and clock signal.
EXTERNAL DRIVE – A drive mounted in an enclosure
separate from the PC or computer system enclosure, with its
own power supply and fan, and connected to the system by
a cable.
DEDICATED SERVO – A surface separate from the
surface used for data that contains only disk timing and
positioning information and contains no data.
DEFECT MANAGEMENT – A method that is
implemented to ensure long term data integrity. Defect
management eliminates the need for user defect maps. This
is accomplished by scanning the disk drives at the factory for
defective sectors. Defective sectors are deallocated prior to
shipment. In addition, during regular use, the drive
continues to scan and compensate for any new defective
sectors on the disk.
F
FAT – Acronym for file allocation table. A data table stored
on the outer edge of a disk that tells the operating system
which sectors are allocated to each file and in what order.
FCI – Acronym for flux changes per inch. See also BPI.
FILE SERVER – A computer that provides network
stations with controlled access to shareable resources. The
network operating system is loaded on the file server, and
most shareable devices (disk subsystems, printers) are
attached to it. The file server controls system security and
monitors station-to-station communications. A dedicated
file server can be used only as a file server while it is on the
network. A non dedicated file server can be used
DISK – In general, any circular-shaped data-storage
medium that stores data on the flat surface of the platter. The
most common type of disk is the magnetic disk, which stores
data as magnetic patterns in a metal or metal-oxide coating.
Magnetic disks come in two forms: floppy and hard. Optical
recording is a newer disk technology that gives higher
capacity storage but at slower access times.
simultaneously as a file server and a workstation.
DISK CONTROLLER – A plug-in board, or embedded
circuitry on the drive, that passes information to and from
the disk. The Maxtor disk drives all have controllers
embedded on the drive printed-circuit board.
FLUX DENSITY – The number of magnetic field
patterns that can be stored in a given length of disk surface.
The number is usually stated as flux changes per inch (FCI),
with typical values in the thousands.
DISKWARE – The program instructions and data stored
on the disk for use by a processor.
FLYING HEIGHT – The distance between the
read/write head and the disk surface caused by a cushion of
air that keeps the head from contacting the media. Smaller
flying heights permit more dense storage of data, but require
more precise mechanical designs.
DMA – Acronym for direct memory access. A process by
which data moves directly between a disk drive (or other
device) and system memory without passing through the
CPU, thus allowing the system to continue processing other
tasks while the new data is being retrieved.
FORMAT – To write onto the disk surface a magnetic track
pattern that specifies the locations of the tracks and sectors.
This information must exist on a disk before it can store any
user data. Formatting erases any previously stored data.
DRIVE – Short form of disk drive.
DRIVE GEOMETRY – The functional dimensions of a
drive in terms of the number of heads, cylinders, and sectors
per track. See also logical format.
G-2 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
FORMATTED CAPACITY – The amount of room left
to store data on the disk after the required space has been
used to write sector headers, boundary definitions, and
timing information generated by a format operation. All
Maxtor drive capacities are expressed in formatted capacity.
I
INITIALIZE – See low level formatting.
INITIATOR – A SCSI device that requests another SCSI
device to perform an operation. A common example of this
is a system requesting data from a drive. The system is the
initiator and the drive is the target.
FORM FACTOR – The physical outer dimensions of a
device as defined by industry standard. For example, most
Maxtor disk drives use a 3 1/2-inch form factor.
INTERFACE – A hardware or software protocol,
contained in the electronics of the disk controller and disk
drive, that manages the exchange of data between the drive
and computer.
G
GIGABYTE (GB) – One billion bytes (one thousand
megabytes).
INTERLEAVE– The arrangement of sectors on a track. A
1:1 interleave arranges the sectors so that the next sector
arrives at the read/write heads just as the computer is ready
to access it. See also interleave factor.
GUIDE RAILS – Plastic strips attached to the sides of a
disk drive mounted in an IBM AT and compatible
computers so that the drive easily slides into place.
INTERLEAVE FACTOR – The number of sectors that
pass beneath the read/write heads before the next numbered
sector arrives. When the interleave factor is 3:1, a sector is
read, two pass by, and then the next is read. It would take
three revolutions of the disk to access a full track of data.
Maxtor drives have an interleave of 1:1, so a full track of data
can be accessed within one revolution of the disk, thus
offering the highest data throughput possible.
H
HALF HEIGHT – Term used to describe a drive that
occupies half the vertical space of the original full size
5 1/4-inch drive. 1.625 inches high.
HARD DISK – A type of storage medium that retains data
as magnetic patterns on a rigid disk, usually made of an iron
oxide or alloy over a magnesium or aluminum platter.
Because hard disks spin more rapidly than floppy disks, and
the head flies closer to the disk, hard disks can transfer data
faster and store more in the same volume.
INTERNAL DRIVE – A drive mounted inside one of a
computer’s drive bays (or a hard disk on a card, which is
installed in one of the computer’s slots).
K
HARD ERROR – A repeatable error in disk data that
persists when the disk is reread, usually caused by defects in
the media surface.
KILOBYTE (Kb) – A unit of measure consisting of 1,024
10
(2 ) bytes.
HEAD – The tiny electromagnetic coil and metal pole
piece used to create and read back the magnetic patterns
(write and read information) on the media.
L
LANDING ZONE – A position inside the disk’s inner
cylinder in a non data area reserved as a place to rest the
heads during the time that power is off. Using this area
prevents the heads from touching the surface in data areas
upon power down, adding to the data integrity and
reliability of the disk drive.
HIGH-CAPACITY DRIVE – By industry conventions
typically a drive of 1 gigabytes or more.
HIGH-LEVEL FORMATTING– Formatting performed
by the operating system’s format program. Among other
things, the formatting program creates the root directory and
file allocation tables. See also low-level formatting.
LATENCY – The period of time during which the
read/write heads are waiting for the data to rotate into
position so that it can be accessed. Based on a disk rotation
speed of 3,662 rpm, the maximum latency time is 16.4
milliseconds, and the average latency time is 8.2
milliseconds.
HOME – Reference position track for re-calibration of the
actuator, usually the outer track (track 0).
HOST ADAPTER – A plug-in board that forms the
interface between a particular type of computer system bus
and the disk drive.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
G-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
LOGICAL FORMAT – The logical drive geometry that
appears to an AT system BIOS as defined by the drive tables
and stored in CMOS. With an installation program like Disk
Manager, the drive can be redefined to any logical
MTTF – MTTF is a basic measure of reliability for
non-repairable systems. It is the mean time expected until
the first failure of a piece of equipment. MTTF is a statistical
value and is meant to be the mean over a long period of time
and large number of units. For constant failure rate systems,
MTTF is the inverse of the failure rate. If failure rate is in
failures/million hours, MTTF = 1,000,200 / Failure Rate
for components with exponential distributions.
parameters necessary to adapt to the system drive tables.
LOOK AHEAD – The technique of buffering data into
cache RAM by reading subsequent blocks in advance to
anticipate the next request for data. The look ahead
technique speeds up disk access of sequential blocks of data.
MTTR – Mean Time To Repair. The average time it takes
to repair a drive that has failed for some reason. This only
takes into consideration the changing of the major
sub-assemblies such as circuit board or sealed housing.
Component level repair is not included in this number as
this type of repair is not performed in the field.
LOW-LEVEL FORMATTING– Formatting that creates
the sectors on the platter surfaces so the operating system can
access the required areas for generating the file structure.
Maxtor drives are shipped with the low-level formatting
already done.
O
LOW PROFILE– Describes drives built to the 3 1/2-inch
OVERHEAD – The processing time of a command by the
controller, host adapter or drive prior to any actual disk
accesses taking place.
form factor, which are only 1 inch high.
M
OVERWRITE – To write data on top of existing data,
erasing it.
MB – See megabyte.
MEDIA – The magnetic film that is deposited or coated on
an aluminum substrate which is very flat and in the shape of
a disk. The media is overcoated with a lubricant to prevent
damage to the heads or media during head take off and
landing. The media is where the data is stored inside the disk
in the form of magnetic flux or polarity changes.
OXIDE – A metal-oxygen compound. Most magnetic
coatings are combinations of iron or other metal oxides, and
the term has become a general one for the magnetic coating
on tape or disk.
P
MEGABYTE (Mb) – A unit of measurement equal to
1,024 kilobytes, or 1,048,576 bytes except when referring to
disk storage capacity.
PARTITION – A portion of a hard disk devoted to a
particular operating system and accessed as one logical
volume by the system.
1 MB = 1,000,000 bytes when referring to disk storage
capacity. See also kilobyte.
PERFORMANCE – A measure of the speed of the drive
during normal operation. Factors affecting performance are
seek times, transfer rate and command overhead.
MEGAHERTZ– A measurement of frequency in millions
of cycles per second.
PERIPHERAL – A device added to a system as an
enhancement to the basic CPU, such as a disk drive, tape
drive or printer.
MHz – See megahertz.
MICROPROCESSOR – The integrated circuit chip that
performs the bulk of data processing and controls the operation
of all of the parts of the system. A disk drive also contains a
microprocessor to handle all of the internal functions of the
drive and to support the embedded controller.
PHYSICAL FORMAT – The actual physical layout of
cylinders, tracks, and sectors on a disk drive.
PLATED MEDIA – Disks that are covered with a hard
metal alloy instead of an iron-oxide compound. Plated
disks can store greater amounts of data in the same area as
a coated disk.
MICROSECOND (µs) – One millionth of a second
(.000001 sec.).
MILLISECOND (ms) – One thousandth of a second
(.001 sec.).
G-4 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
PLATTER – An disk made of metal (or other rigid
material) that is mounted inside a fixed disk drive. Most
drives use more than one platter mounted on a single spindle
(shaft) to provide more data storage surfaces in a small
package. The platter is coated with a magnetic material that
is used to store data as transitions of magnetic polarity.
ROM – Acronym for read only memory. Usually in the form
of an ROM in the controller that contains programs that can
be accessed and read but not modified by the system.
ROTARY ACTUATOR – The rotary actuator replaces
the stepper motor used in the past by many hard disk
manufacturers. The rotary actuator is perfectly balanced and
rotates around a single pivot point. It allows closed-loop
feedback positioning of the heads, which is more accurate
than stepper motors.
POH– Acronym for power on hours. The unit of measurement
for Mean Time Between Failure as expressed in the number of
hours that power is applied to the device regardless of the
amount of actual data transfer usage. See MTBF.
ROTATIONAL LATENCY– The delay between when
the controller starts looking for a specific block of data on a
track and when that block rotates around to where it can be
read by the read/write head. On the average, it is half of the
time needed for a full rotation (about 8 ms.).
POSITIONER – See actuator.
R
RAM – Acronym for random access memory. An integrated
circuit memory chip which allows information to be stored
and retrieved by a microprocessor or controller. The
information may be stored and retrieved in any order
desired, and the address of one storage location is as readily
accessible as any other.
S
SATA - Acronym for Serial ATA.
SCSI – Acronym for Small Computer System Interface, an
American National Standards Institute (ANSI) version of
Shugart Associates' SASI interface between the computer
and controller. SCSI has grown in popularity and is one of
the most flexible and intelligent interfaces available.
RAM DISK – A “phantom disk drive” for which a
section of system memory (RAM) is set aside to hold data,
just as if it were a number of disk sectors. The access to this
data is extremely fast but is lost when the system is reset or
turned off.
SECTOR – A section of space along a track on the disk, or
the data that is stored in that section. Hard disks most often
have sectors that are 512 data bytes long plus several bytes
overhead for error correcting codes. Each sector is preceded
by ID data known as a header, which cannot be overwritten.
READ AFTER WRITE – A mode of operation that has
the computer read back each sector on the disk, checking
that the data read back is the same as recorded. This slows
disk operations, but raises reliability.
SEEK – A movement of the disk read/write head in or out
to a specific track.
READ VERIFY – A disk mode where the disk reads in
data to the controller, but the controller only checks for
errors and does not pass the data on to the system.
SERVO DATA – Magnetic markings written on the media
that guide the read/write heads to the proper position.
READ/WRITE HEAD – The tiny electromagnetic coil
and metal pole piece used to create and read back the
magnetic patterns (write or read information) on the disk.
Each side of each platter has its own read/write head.
SERVO SURFACE – A separate surface containing only
positioning and disk timing information but no data.
SETTLE TIME – The interval between when a track to
track movement of the head stops, and when the residual
vibration and movement dies down to a level sufficient for
reliable reading or writing.
REMOVABLE DISK – Generally said of disk drives
where the disk itself is meant to be removed, and in
particular of hard disks using disks mounted in cartridges.
Their advantage is that multiple disks can be used to increase
the amount of stored material, and that once removed, the
disk can be stored away to prevent unauthorized use.
SHOCK RATING – A rating (expressed in Gs) of how
much shock a disk drive can sustain without damage.
RLL – Run Length Limited. A method used on some hard
disks to encode data into magnetic pulses. RLL requires
more processing, but stores almost 50% more data per disk
than the MFM method.
SOFT ERROR – An error in reading data from the disk
that does not recur if the same data is reread. Often caused
by power fluctuations or noise spikes.
SOFT SECTORED – Disks that mark the beginning of
each sector of data within a track by a magnetic pattern.
Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
G-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
SPINDLE – The center shaft of the disk upon which the
drive’s platters are mounted.
U
UNFORMATTED CAPACITY – The total number of
bytes of data that could be fit onto a disk. Formatting the
disk requires some of this space to record location, boundary
definitions, and timing information. After formatting, user
data can be stored on the remaining disk space, known as
formatted capacity. The size of a Maxtor drive is expressed
in formatted capacity.
SPUTTER – A type of coating process used to apply the
magnetic coating to some high-performance disks. In
sputtering, the disks are placed in a vacuum chamber and the
coating is vaporized and deposited on the disks. The resulting
surface is hard, smooth, and capable of storing data at high
density. Maxtor disk drives use sputtered thin film disks.
STEPPER – A type of motor that moves in discrete
amounts for each input electrical pulse. Stepper motors used
to be widely used for read/write head positioner, since they
can be geared to move the head one track per step. Stepper
motors are not as fast or reliable as the rotary voice coil
actuators which Maxtor disk drives use.
V
VOICE COIL – A type of motor used to move the disk
read/write head in and out to the right track. Voice-coil
actuators work like loudspeakers with the force of a
magnetic coil causing a proportionate movement of the
head. Maxtor's actuator uses voice-coil technology, and
thereby eliminates the high stress wearing parts found on
stepper motor type actuators.
SUBSTRATE – The material the disk platter is made of
beneath the magnetic coating. Hard disks are generally made
of aluminum or magnesium alloy (or glass, for optical disks)
while the substrate of floppies is usually mylar.
W
SURFACE – The top or bottom side of the platter which
is coated with the magnetic material for recording data. On
some drives one surface may be reserved for positioning
information.
WEDGE SERVO – The position on every track that
contains data used by the closed loop positioning control.
This information is used to fine tune the position of the
read/write heads exactly over the track center.
WINCHESTER DISKS – Hard disks that use a
technology similar to an IBM model using Winchester as the
code name. These disks use read/write heads that ride just
above the magnetic surface, held up by the air flow created
by the turning disk. When the disk stops turning, the heads
land on the surface, which has a specially lubricated coating.
Winchester disks must be sealed and have a filtration system
since ordinary dust particles are large enough to catch
between the head and the disk.
T
THIN FILM – A type of coating, used for disk surfaces.
Thin film surfaces allow more bits to be stored per disk.
TPI – Acronym for tracks per inch. The number of tracks or
cylinders that are written in each inch of travel across the
surface of a disk.
TRACK – One of the many concentric magnetic circle
patterns written on a disk surface as a guide to where to store
and read the data.
WRITE ONCE – In the context of optical disks,
technologies that allow the drive to store data on a disk and
read it back, but not to erase it.
TRACK DENSITY – How closely the tracks are packed
on a disk surface. The number is specified as tracks per
inch (TPI).
TRACK TO TRACK SEEK TIME– The time required
for the read/write heads to move to an adjacent track.
TRANSFER RATE – The rate at which the disk sends
and receives data from the controller. Drive specifications
usually reference a high number that is the burst mode rate
for transferring data across the interface from the disk buffer
to system RAM. Sustained data transfer is at a much lower
rate because of system processing overhead, head switches,
and seeks.
G-6 Maxtor DiamondMax 17 80-160GB AT Hard Disk Drive
Download from Www.Somanuals.com. All Manuals Search And Download.
|