INSTALLATION & OPERATIONS MANUAL
MASTER-BILT Products
908 Highway 15 North
New Albany, MS 38652
Phone: 800-6848988
REV 2-29-12
By: LN
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove plastic overwrap, banding and corrugation packaging. The wooden skid is removed by unscrewing
6-8 hex head screws holding the skid. Glass Door Models: Remove glass door support bracket(s) and
protective foam block(s).
All merchandisers are tested, inspected and carefully packaged to ensure each unit arrives ready for
operation. Please return postage paid warranty card to activate merchandiser warranty. (See back page of
manual) Retain for future reference.
Note: Merchandiser should be moved close to an upright position. If merchandiser is tilted 45° past
vertical, it is recommended the unit not be used for a time equal to the time it was not vertical. This
will allow the compressor lubricant to return to level for designed operation.
The merchandiser installation location should have a solid level base. If merchandiser is not level, the self-
closing doors on upright models may not close or seal properly. The installation location must also provide
good air flow for designed refrigeration system operation. DO NOT block refrigeration grill openings. Grill
blockage may result in compressor failure.
Outdoor merchandisers: Locations shaded from sunlight are recommended for more economical operation.
Auto-defrost models: Leave sufficient space behind merchandiser to prevent the drain hose from being
kinked or obstructed. A blocked hose will not allow unit cooler condensate water drainage.
Indoor merchandisers: Locations must keep the area above and within full top cover clear from storage
items or from obstructions. As per above, location must provide good air flow for designed refrigeration
system. Auto-defrost glass door models: Remove condensate evaporator carton from inside merchandiser
and install evaporator on back of merchandiser per instruction sheet inside carton. (Screwdriver required)
Optional item installation: Refer to instruction sheet inside carton.
1. Electrical: The electrical voltage and frequency cycle at installation site must coincide with merchandiser
decal serial label. Electrical service connections must be in accordance with the National Electrical Code,
state code and any local code that may apply. All merchandisers are wired to a polarized power cord with
3-prong plug.
CAUTION: Improper use or removal of the grounding plug can result in risk of electrical shock.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The merchandiser must be plugged into a 115 volt, 60 HZ grounded receptacle electrical outlet with a
circuit fuse or breaker. (See figure 1). The condensing unit data plate will indicate the maximum
fuse/breaker size. DO NOT use extension cords. Extension cords may decrease the voltage to the unit and
ultimately cause the compressor to fail.
NOTE: Some outdoor locations require ground fault interrupt (GFI) outlets. These outlets may trip
upon condensing unit start. Refrigeration equipment is exempt in some areas from GFI
requirements. Local electric codes should be checked.
Plug merchandiser power cord into lower receptacle of electrical outlet. The condensing unit will start, the
light will illuminate on glass door models, and unit cooler evaporator fans will start on Auto-Defrost
models. The condensing unit will continue to run until air temperature in cabinet is approximately +18° F.
If merchandiser has a condensate evaporator, plug evaporator power cord into upper receptacle of electrical
outlet and heater rod will heat.
2. Temperature Control: Cabinet temperature is maintained by cycling the condensing unit automatically
with a thermostat. On Auto-Defrost models, the thermostat is located on the left end of unit cooler cover.
On Cold Wall models, the thermostat is located on a bracket under the condensing unit cover. (The
thermostat for Low Profile Cold Wall models is located on bracket at upper rear interior).
The temperature is adjusted by turning the control knob. Turning the control knob fully counterclockwise
will shut off power to compressor. DO NOT readjusts the internal adjustments of the control without
consulting factory.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Loading Ice: After merchandiser is operating at required temperature, load with packaged ice. Stacked
packaged ice should not exceed heights that will cause poor refrigeration efficiency. Approximately 6"
needs to be clear from top of stacked ice to top of inside interior for effective refrigerated ice storage. Auto-
Defrost units require good fan air flow for effective circulation. DO NOT block evaporator assembly
fan/grill openings and air channels require unrestricted air flow convection around packaged ice. Cold Wall
units should have ice stacked to allow air access to thermostat sensor located at upper rear interior.
CAUTION: Disconnect power plug before maintenance on electrical components to avoid
risk of electrical shock
1. Refrigeration: Clean refrigeration cover grill openings, condenser fins, and condenser fan
blades every three (3) months or more often if refrigeration is exposed to dusty environment.
A dirty condensing unit can cause merchandiser to become less efficient, and may lead to
compressor failure.
Note: DO NOT place any type of filter media for dust/dirt collection in front of condenser coil.
Testing has shown filter media alone creates restricted air flow
2. Defrosting: Frost forms on the evaporator when door is opened and warm air enters
merchandiser.
A. Auto-Defrost (AD) Evaporator: Auto-Defrost merchandisers utilize a unit cooler evaporator
with an electric defrost heating element to melt the frost off the evaporator coil. The defrost
cycle is controlled by a defrost timer which energizes a defrost heating element every four
(4) hours for 14 to 16 minutes.
Before each reloading of packaged ice: Inspect operation of unit cooler fan motor(s). Replace
motor(s) not operating or merchandiser refrigeration will not work effectively. Inspect unit
cooler drain hose to be sure it is not kinked or plugged. Water must drain to condensate
evaporator for designed operation. (See condensate evaporation maintenance)
B. Cold Wall (CW) Evaporator: Cold Wall merchandisers utilize the merchandiser's interior
wall surface as the refrigeration evaporator. Therefore, frost accumulation will occur on all
wall surfaces. The merchandiser can be defrosted using a wooden paddle, plastic scraper, or
hot air. DO NOT use a sharp instrument to "chop" the frost as you may penetrate wall and
refrigerant tubing and do irreparable damage. A drain plug is located under the ice pallet to
help allow water to drain.
C. Condensate Evaporator: Inspect operation and condition of evaporator every three (3)
months. The heating rod should be heating and examined for excessive corrosion. Failure of
the heating rod to heat properly can result in the drain pan water overflowing. Also,
accumulative dust buildup may limit proper operation of the unit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Electrical: Inspect each month all power harnesses for any cracks, abrasions or damage to
connection plugs. Replace any defective wiring or harnesses.
4. Door(s): Inspect each month for component wear, function and secure attachment.
A. Gasket(s) should be examined for tears or any other problems that would cause loss of seal.
Replace torn/worn gaskets to maintain correct temperature and refrigeration efficiency.
B. Hinges exposed to harsh environmental conditions may require a lubricant for ease of
operation. Spray a light penetrating oil on hinge pivot points to ease the work load and
extend life of hinge. Tighten any loose screws.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Cleaning: Schedule yearly cleaning of merchandiser interior with solution of 8 tablespoons of baking
soda to 1 gallon of warm water. DO NOT use strong detergents, abrasive cleansers, solvents, wax or
polish as they are likely to leave objectionable odors which may be absorbed by the ice. Wash the
outside surfaces with a mild soap and warm water applied with a soft sponge or cloth. Wax exterior
to maintain appearance and extend life of paint.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
DESCRIPTION
PART #
ITEM
DESCRIPTION
PART #
1. Condensing Unit: Provide
condensing unit model number
14. Door, Stucco Stainless Steel
27" x 27" with gasket
5590025
15. Door Gasket for
27" x 27" solid door
1030016
1911019
2. Drier
1323002
1328023
1328046
1270047
1270043
Timer
Thermostat
Power Harness (AD & CW)
Coldwall Adapter Harness
16. Door Hinge with cover for 27" x 27"
solid door
17. Door, Stucco Stainless Steel
27" x 46" with gasket
5590030
1030014
3. Unit Cooler Evaporator Parts:
Fan Guard
1396023
1392008
1101401
1393029
1328003
1261007
1261008
1261009
Fan Blade
Fan Mounting Bracket
Fan Motor
Defrost Limit Thermostat
LCL 120 Defrost Heater
LCL 170 Defrost Heater
LCL 190/280 Defrost Heater
18. Door Gasket for
27" x 46" solid door
19. Glass Door, 28" x 47" Silver Frame
Glass Door, 28" x 47" Gold Frame
1412012
1412013
20. Door Gasket for 28" x 47" glass door
1490007
21. Door Hinge for 28" x 47" door:
Silver w/spring & cover
Gold w/spring & cover
4. Full Top Enclosure: Provide
merchandiser model number.
1911002
1911022
1990008
1990009
1990002
5. "ICE" Decal for full top (Red)
“ICE” Decal for full top (Blue)
1070076
1070069
Silver Cover
Gold Cover
Spring Kit
6. "ICE" sign for full top (Red)
“ICE” sign for full top (Blue)
5991021
5991022
22. "ICE" Decals (Red) One Set "ICE"
Decals (Blue) One Set
1070074
1070070
7. Cover w/o flasher assy. and decals
Cover w/flasher assy. and decals
5840035-5
5849000-5
23. Rain Shield for 27" x 46" solid door
24. Ice Pallet 22" x 28"
5120076-1
1050079
8. "Packaged Ice" Decal.
1070077
9. "Crystal Clear" Decal (Red)
“Crystal Clear” Decal (Blue)
1070075
1070071
25. Fluorescent Light Fixture (w/bulb)
Fluorescent Bulb
5239006
1216005
10. J-Bolt for all solid doors
1160008
26. Condensate evaporator assy. for
automatic defrost models (White)
5349040
11. Door Hasp for all solid doors
5120001
27. Condensate evaporator, heater rod
28. Skid Plate
1261004
1050005
12. Door Handle for all solid doors
1914001
1915001
13. Check Chain for 27" x 27" solid door
Provide Leer merchandiser Model number and Serial number for accurate processing of parts orders.
Return only authorized parts to this address:
MASTER-BILT Products
908 Highway 15 North
New Albany, MS 38652
NOTE: Leer electrical and refrigeration parts are all U.L. recognized and installed to comply with U.L. merchandiser product
listings. Replacement of parts that are not U.L. recognized and not installed per original assembly will void merchandiser U.L.
listing and Factory warranty per "General Provisions.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀꢁꢂ¬(WYꢃ¬ꢄꢅ¬.ORTH¬s¬.EW¬!LBANYꢆ¬-3¬ꢇꢂꢈꢅꢉ¬s¬ꢂꢁꢁꢊꢈꢋꢌꢊꢄꢉꢂꢋꢍꢈꢈꢉꢊꢅꢇꢋꢊꢀꢁꢈꢄ¬s¬&!8ꢎ¬ꢂꢁꢁꢊꢉꢇꢉꢊꢇꢀꢈꢈ
7ARRANTY¬0ARTS¬ꢏ¬3ERVICEꢎ¬ꢂꢁꢁꢊꢈꢂꢋꢊꢂꢀꢂꢂ¬s¬&!8ꢎ¬ꢂꢈꢈꢊꢂꢂꢉꢊꢌꢈꢉꢀ
,)-)4%$¬/.%ꢀ9%!2¬0!243¬ꢁ¬,!"/2¬7!22!.49¬&/2¬4(%¬&/,,/7).'¬#!").%4¬-/$%,3ꢂ
"'2ꢆ¬-3#ꢆ¬-3&ꢆ¬)-ꢆ¬-"""ꢆ¬-""#ꢆ¬-"#ꢆ¬-"#"ꢆ¬-"$$ꢆ¬-"2ꢆ¬-"&ꢆ¬-"'2ꢆ¬-"04ꢆ¬-"30ꢆ¬-"3-0ꢆ¬
-"5&ꢆ¬-"52
-ASTERꢊ"ILT¬0RODUCTS¬ꢐTHE¬h#OMPANYv ¬WARRANTS¬TO¬THE¬ORIGINAL¬PURCHASERꢊUSER¬THAT¬ITS¬REFRIGERATION¬EQUIPMENTꢆ¬AT¬THE¬TIME¬OF¬
DELIVERYꢆ¬WILL¬BE¬FREE¬FROM¬DEFECTS¬IN¬MATERIAL¬AND¬WORKMANSHIPꢃ¬¬-ASTERꢊ"ILT¬WILL¬BEAR¬THE¬REASONABLE¬AND¬CUSTOMARY¬LABOR¬EXPENSE¬
TO¬REPAIR¬OR¬REPLACE¬ANY¬COMPONENT¬PART¬ꢐINCLUDING¬SAID¬PART ¬FOUND¬TO¬BE¬DEFECTIVE¬UNDER¬THE¬TERMS¬AND¬CONDITIONS¬AS¬OUTLINED¬
UNDER¬-ASTERꢊ"ILTꢑS¬STANDARD¬ONE¬ꢐꢄ ¬YEAR¬PARTS¬WARRANTYꢃ¬4HE¬PURCHASERꢊUSER¬WILL¬HAVE¬THE¬SOLE¬RESPONSIBILITY¬AND¬BEAR¬ALL¬EXPENSES¬
OF¬REMOVING¬AND¬RETURNING¬THE¬DEFECTIVE¬PART¬OR¬EQUIPMENTꢃ¬-ASTERꢊ"ILT¬WILL¬REIMBURSE¬SAID¬LABOR¬EXPENSES¬TO¬THE¬ORIGINAL¬PURCHASER¬
ONLY¬IF¬AFTER¬EVALUATING¬THE¬ORIGINAL¬SERVICE¬INVOICE¬SUBMITTED¬BY¬THE¬ORIGINAL¬PURCHASERꢊUSER¬-ASTERꢊ"ILT¬DETERMINES¬THAT¬THIS¬
WARRANTY¬APPLIESꢃ¬¬4HE¬LABOR¬WARRANTY¬SHALL¬APPLY¬ONLY¬TO¬SELFꢊCONTAINED¬EQUIPMENT¬INSTALLED¬BY¬AUTHORIZED¬OR¬APPROVED¬-ASTERꢊ"ILT¬
DEALERSꢆ¬DISTRIBUTORSꢆ¬SERVICE¬COMPANIES¬OR¬REFRIGERATION¬CONTRACTORSꢃ¬¬4HE¬LABOR¬WARRANTY¬DOES¬NOT¬COVER¬THE¬COST¬ꢐPARTS¬OR¬LABOR ¬
OF¬INSTALLATIONꢆ¬STARTꢊUPꢆ¬NORMAL¬MAINTENANCEꢆ¬OR¬NORMAL¬CONTROL¬ADJUSTMENTꢃ¬¬9OUR¬LOCAL¬COMPRESSOR¬SUPPLIER¬SHOULD¬EXCHANGE¬THE¬
COMPRESSOR¬AT¬NO¬CHARGE¬DURING¬lRST¬YEAR¬WARRANTYꢃ¬#LAIMS¬UNDER¬THIS¬7ARRANTY¬MUST¬BE¬SUBMITTED¬ELECTRONICALLY¬BY¬THE¬3ERVICE¬
#OMPANY¬WITHIN¬ꢀꢁ¬DAYS¬FROM¬THE¬DATE¬OF¬REPAIRꢃ¬#LAIMS¬NOT¬lLED¬WITHIN¬THIS¬TIME¬FRAME¬WILL¬BE¬SUBJECT¬TO¬DENIAL¬WITHOUT¬PRIOR¬
APPROVALꢃ¬4O¬SUBMIT¬A¬CLAIM¬YOU¬MUST¬HAVE¬A¬-ASTERꢊ"ILT¬SERIAL¬NUMBERꢃ
!NY¬DEFECTS¬CAUSED¬BY¬MISAPPLICATIONꢆ¬ABNORMAL¬USE¬OR¬MISUSEꢆ¬LACK¬OF¬OR¬IMPROPER¬MAINTENANCEꢆ¬DAMAGE¬BY¬THIRD¬PARTIESꢆ¬
ALTERATIONSꢆ¬ACTS¬OF¬'ODꢒ¬FAILURE¬TO¬FOLLOW¬INSTALLATIONꢆ¬MAINTENANCE¬OR¬SAFETY¬INSTRUCTIONS¬OR¬ANY¬OTHER¬EVENT¬BEYOND¬THE¬CONTROL¬OF¬
THE¬#OMPANY¬WILL¬NOT¬BE¬COVERED¬UNDER¬THIS¬7ARRANTYꢃ
4HE¬OBLIGATION¬OF¬-ASTERꢊ"ILT¬SHALL¬BE¬LIMITED¬TO¬REPAIRING¬OR¬REPLACING¬ꢐAT¬THE¬OPTION¬OF¬THE¬#OMPANY ¬ANY¬PARTꢆ¬WHICH¬IS¬DEFECTIVE¬
IN¬THE¬REASONABLE¬OPINION¬OF¬THE¬#OMPANYꢃ¬¬4HE¬COST¬OF¬SERVICE¬LABOR¬REIMBURSED¬WILL¬BE¬BASED¬ON¬STRAIGHTꢊTIME¬RATE¬AND¬REASONABLE¬
TIME¬FOR¬THE¬REPAIR¬OF¬THE¬DEFECTꢃ
4()3¬7!22!.49¬)3¬%8#,53)6%¬!.$¬).¬,)%5¬/&¬!,,¬/4(%2¬7!22!.4)%3ꢃ¬%802%33¬/2¬)-0,)%$ꢃ¬).#,5$).'¬4(%¬
)-0,)%$¬7!22!.4)%3¬/&¬-%2#(!.4!"),)49¬!.$¬&)4.%33¬&/2¬!¬0!24)#5,!2¬0520/3%ꢄ
)N¬NO¬EVENT¬SHALL¬THE¬#OMPANY¬BE¬LIABLE¬FOR¬LOSS¬OF¬USEꢃ¬REVENUE¬OR¬PROlT¬OR¬FOR¬ANY¬OTHER¬INDIRECTꢃ¬INCIDENTALꢃ¬
SPECIAL¬OR¬CONSEQUENTIAL¬DAMAGES¬INCLUDINGꢃ¬BUT¬NOT¬LIMITED¬TOꢃ¬FOOD¬SPOILAGE¬OR¬PRODUCT¬LOSSꢄ
4HIS¬WARRANTY¬SHALL¬APPLY¬ONLY¬WITHIN¬THE¬CONTINENTAL¬5NITED¬3TATESꢆ¬IT¬TERRITORIES¬AND¬POSSESSIONSꢆ¬#ANADA¬AND¬-EXICOꢃ
%84%.$%$¬&/52ꢀ9%!2¬#/-02%33/2¬2%0,!#%-%.4¬7!22!.49¬
4HE¬#OMPANY¬WARRANTS¬TO¬THE¬ORIGINAL¬PURCHASERꢊUSER¬THAT¬IT¬WILL¬REPLACE¬THE¬COMPRESSOR¬ON¬THE¬%QUIPMENT¬IF¬FOUNDꢆ¬IN¬THE¬
REASONABLE¬OPINION¬OF¬THE¬#OMPANYꢆ¬TO¬BE¬DEFECTIVE¬IN¬MATERIAL¬OR¬WORKMANSHIP¬IF¬WRITTEN¬NOTICE¬IS¬RECEIVED¬WITHIN¬lVE¬YEARS¬FROM¬DATE¬
OF¬SHIPMENTꢃ
$EFECTIVE¬CONDITIONS¬CAUSED¬BY¬ABNORMAL¬USE¬OR¬MISUSEꢆ¬LACK¬OF¬OR¬IMPROPER¬MAINTENANCEꢆ¬DAMAGE¬BY¬THIRD¬PARTIESꢆ¬ALTERATIONSꢆ¬ACTS¬
OF¬'ODꢆ¬FAILURE¬TO¬FOLLOW¬INSTALLATIONꢆ¬MAINTENANCE¬OR¬SAFETY¬INSTRUCTIONS¬OR¬ANY¬OTHER¬EVENT¬BEYOND¬THE¬CONTROL¬OF¬THE¬#OMPANY¬WILL¬NOT¬
BE¬COVERED¬UNDER¬THIS¬WARRANTYꢃ
4HE¬COMPRESSOR¬REPLACEMENT¬WARRANTY¬DOES¬NOT¬APPLY¬TO¬ANY¬PART¬OF¬THE¬EQUIPMENT¬OTHER¬THAT¬THE¬COMPRESSORꢃ¬¬4HE¬PURCHASERꢊUSER¬
WILL¬HAVE¬THE¬SOLE¬RESPONSIBILITY¬AND¬BEAR¬ALL¬EXPENSES¬OF¬REMOVING¬AND¬RETURNING¬THE¬DEFECTIVE¬COMPRESSOR¬TO¬THE¬#OMPANY¬AS¬WELL¬AS¬
THE¬COST¬OF¬REINSTALLING¬THE¬REPLACEMENT¬COMPRESSORꢃ¬¬4HE¬#OMPANY¬MAY¬SATISFY¬ITS¬OBLIGATIONS¬HEREUNDER¬BY¬SUPPLYING¬A¬REPLACEMENT¬
COMPRESSORꢆ¬WHICH¬IS¬REASONABLY¬SIMILAR¬IN¬DESIGN¬AND¬CAPACITYꢃ
4()3¬7!22!.49¬)3¬%8#,53)6%¬!.$¬).¬,)%5¬/&¬!,,¬/4(%2¬7!22!.4)%3ꢃ¬%802%33¬/2¬)-0,)%$ꢃ¬).#,5$).'¬4(%¬
)-0,)%$¬7!22!.4)%3¬/2¬-%2#(!.4!"),)49¬!.$¬&)4.%33¬&/2¬!¬0!24)#5,!2¬0520/3%ꢄ
)N¬NO¬EVENT¬SHALL¬THE¬#OMPANY¬BE¬LIABLE¬FOR¬LOSS¬OF¬USEꢃ¬REVENUE¬OR¬PROlT¬OR¬FOR¬ANY¬OTHER¬INDIRECTꢃ¬INCIDENTALꢃ¬
SPECIAL¬OR¬CONSEQUENTIAL¬DAMAGES¬INCLUDINGꢃ¬BUT¬NOT¬LIMITED¬TOꢃ¬LOSSES¬INVOLVING¬FOOD¬SPOILAGE¬OR¬PRODUCT¬LOSSꢄ
4HIS¬COMPRESSOR¬REPLACEMENT¬WARRANTY¬SHALL¬APPLY¬ONLY¬WITHIN¬THE¬CONTINENTAL¬5NITED¬3TATESꢆ¬IT¬TERRITORIES¬AND¬POSSESSIONSꢆ¬#ANADA¬
AND¬-EXICOꢃ
2%0,!#%-%.4¬0!24¬7!22!.49
-ASTERꢊ"ILT¬WARRANTS¬TO¬THE¬ORIGINAL¬PURCHASERꢊUSER¬THAT¬ALL¬PARTS¬PURCHASED¬AFTER¬THE¬lRST¬YEAR¬WARRANTY¬PERIOD¬WILL¬BE¬WARRANTED¬FOR¬
ꢀꢁ¬DAYS¬FROM¬INVOICE¬DATEꢃ
3HIPMENT¬$ATEꢎ
3ERIAL¬.UMBERꢎ
ꢄꢉꢍꢄꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
|