Marshall electronic Home Security System V R63P SDI User Manual

Marshall  
Broadcast Multimedia Division  
V-R63P-SDI Instruction Sheet  
The V-R63P-SDI is a rack mountable unit that has three independently controlled 5.8" active matrix LCD panels with  
loop through capability. These 16:9 high-resolution panels have a pixel count of 1200 × 234, and are rated at a very  
bright 350 candle luminance. Each panel has an SDI and a composite video input with an NTSC/PAL switch on the  
back for each channel. Each of the three screens has a built-in color bar generator, controls for brightness, color, tint,  
and contrast, and a selectable aspect ratio of 16:9 or 4:3. A built in 3 color tally system is also provided for each  
screen. Unit comes complete with power supply, and fits into any standard EIA 19" rack, at only 3 rack spaces high.  
The operation of the V-R63P-SDI is fairly straightforward, however, please take note of the following:  
1. The V-R63P-SDI has been designed to fit in a 3U space on your rack. It is important to use 4 screws to hold  
the ears to the rack. Be certain that the ears are aligned vertically, this is important to the tilt function.  
The V-R63P-SDI has a memory function that will remember the settings of each monitor including power and  
channel selection even if power has been disconnected from the unit.  
2. Each LCD Panel comes with a protective plastic film that must be removed by carefully lifting the film from  
the corner and peeling it off. Be certain not to apply any pressure on the LCD panels, they are fragile and can  
break. Scratched, cracked or broken LCD screens are not covered by our warranty.  
3. The V-R63P-SDI uses 9VDC, 3.5 Amp regulated power. Be certain that these specifications are met when  
using a power supply other than the one supplied to you by Marshall Electronics. The center pin on the coaxial  
power connector for the V-R63P-SDI is the POSITIVE terminal and the outside ring is NEGATIVE. Any battery  
operation of the V-R63P-SDI must have this polarity configuration.  
4. The Video inputs on the rear of the panel are 75 Ohm self-terminated. The loop through feature uses active  
components and is always active as long as power is supplied to the unit regardless of the monitor being On or  
Off. The V-R63P-SDI is also equipped with a 10-bit D/A convertor that converts the SDI input from that channel.  
This D/A convertor uses the SMPTE 259M standard and is reclocked.  
2.5”  
Rear View  
Side View  
Power  
Consumption  
Picture  
Elements  
Display  
Viewing Area  
Dot Pitch  
Inputs  
Color Bars  
Dimensions  
5.01” x 2.83” 0.318mm x  
each panel  
0.307mm  
1 NTSC/PAL  
1 SDI, per panel  
19.125W x  
5.14H x 2.5D  
9 VDC  
3.5 Amps  
5.8” LCD  
Active Matrix  
1200H x  
234V  
Built into unit  
Download from Www.Somanuals.com. All Manuals Search And Download.  

LaCie Portable Speaker USB Speakers Design By Neil Poultan User Manual
Lantronix Switch SLSLP400PS201 User Manual
Lasko Patio Heater 5848 User Manual
LG Electronics Flat Panel Television RU 23LZ50C User Manual
LG Electronics Microwave Oven LMV1630BB User Manual
Linear Microphone RSM 1 User Manual
Magnasonic Clock Radio MAG MM178K User Manual
Maytag Dishwasher MDB7809AWB0 User Manual
Mercedes Benz Stereo Receiver A 002 584 34 71 User Manual
Meridian America DVR DVP 2351 User Manual