Marantz Flat Panel Television PD4220V User Manual

Model PD4220V User Guide

Plasma Monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

Precautions

Warnings and Safety Precaution

Please read this manual carefully before using your plasma

monitor and keep the manual handy for future reference.

This plasma monitor is designed and

manufactured to provide long, trouble-free service.

No maintenance other than cleaning is required.

Please see the section “Plasma monitor cleaning

procedure” on the next page.

CAUTION

The plasma display panel consists of fine picture

elements (cells) with more than 99.99 percent active

cells. There may be some cells that do not produce

light or remain lit.

For operating safety and to avoid damage to the unit,

read carefully and observe the following instructions.

To avoid shock and fire hazards:

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER. NO

USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

1. Provide adequate space for ventilation to avoid internal

heat build-up. Do not cover rear vents or install the unit

in a closed cabinet or shelves.

This symbol warns the user that uninsulated

voltage within the unit may have sufficient

magnitude to cause electric shock.

Therefore, it is dangerous to make any kind

of contact with any part inside of this unit.

If you install the unit in an enclosure, make sure there

is adequate space at the top of the unit to allow hot air

to rise and escape. If the monitor becomes too hot, the

overheat protector will be activated and the monitor will

be turned off. If this happens, turn off the power to the

monitor and unplug the power cord. If the room where

the monitor is installed is particularly hot, move the

monitor to a cooler location, and wait for 60 minutes to

cool the monitor. If the problem persists, contact your

Marantz dealer for service.

This symbol alerts the user that important

literature concerning the operation and

maintenance of this unit has been included.

Therefore, it should be read carefully in

order to avoid any problems.

2. Do not use this unit’s polarized plug with extension cords

or outlets unless the prongs can be completely inserted.

3. Do not expose the unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to

modify the power cord.

5. Unplug the power cord during electrical storms or if

the unit will not be used over a long period.

6. Do not open the cabinet which has potentially dangerous

high voltage components inside. If the unit is damaged in

this way the warranty will be void. Moreover, there is a

serious risk of electric shock.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOTEXPOSE

THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE

THIS UNIT’S POLARIZED PLUG WITHAN EXTENSION CORD

RECEPTACLE OR OTHER OUTLETS, UNLESS THE

PRONGS CAN BE FULLY INSERTED. REFRAIN FROM

OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE

COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

7. Do not attempt to service or repair the unit. The

manufacturer is not liable for any bodily harm or damage

caused if unqualified persons attempt service or open

the back cover. Refer all service to authorized Marantz

Service Centers.

Download from Www.Somanuals.com. All Manuals Search And Download.

To avoid damage and prolong operating life:

1. Use only with 120V 50/60Hz AC power supply.

Continued operation at line voltages greater than 120Volts

AC will shorten the life of the unit, and might even cause

a fire hazard.

2. Handle the unit carefully when installing it and do not

drop.

3. Set the unit away from heat, excessive dust, and direct

sunlight.

4. Protect the inside of the unit from liquids and small

metal objects. In case of accident, unplug the power

cord and have it serviced by an authorized Service

Center.

5. Do not hit or scratch the panel surface as this causes

flaws on the surface of the screen.

6. For correct installation and mounting it is strongly

recommended to use a trained, authorized dealer.

7. As is the case with any phosphor-based display (like a

CRT monitor, for example) light output will gradually

decrease over the life of a Plasma Display Panel.

8. To avoid sulfurization it is strongly recommended not to

place the unit in a dressing room in a public bath or hot

spring bath.

Recommendations to avoid or minimize phosphor burn-in:

Like all phosphor-based display devices and all other gas

plasma displays, plasma monitors can be susceptible to

phosphor burn under certain circumstances. Certain

operating conditions, such as the continuous display of a

static image over a prolonged period of time, can result in

phosphor burn if proper precautions are not taken. To protect

your investment in this plasma monitor, please adhere to the

following guidelines and recommendations for minimizing

the occurrence of image burn:

* Always enable and use your computer’s screen saver

function during use with a computer input source.

* Display a moving image whenever possible.

* Change the position of the menu display from time to time.

* Always power down the monitor when you are finished

using it.

If the plasma monitor is in long term use or continuous

operation take the following measures to reduce the

likelihood of phosphor burn:

* Lower the Brightness and Contrast levels as much as

possible without impairing image readability.

* Display an image with many colors and color gradations

(i.e. photographic or photo-realistic images).

* Create image content with minimal contrast between light

and dark areas, for example white characters on black

backgrounds. Use complementary or pastel color whenever

possible.

Plasma monitor cleaning procedure:

1. Use a soft dry cloth to clean the front panel and bezel

area. Never use solvents such as alcohol or thinner to

clean these surfaces.

2. Clean plasma ventilation areas with a vacuum cleaner

with a soft brush nozzle attachment.

* Avoid displaying images with few colors and distinct,

sharply defined borders between colors.

3. To ensure proper ventilation, cleaning of the ventilation

areas must be carried out monthly. More frequent cleaning

may be necessary depending on the environment in which

the plasma monitor is installed.

* Note:Burn-in is not covered by the warranty.

Contact Marantz Service Center for other recommended

procedures that will best suit your particular application

needs.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommandations importantes

Précautions

Mises en garde et précautions de

Veuillez lire avec attention ce manuel avant d’utiliser le

moniteur à plasma et le conserver accessible pour s’y référer

ultérieurement.

sécurité

Ce moniteur à plasma a été conçu et fabriqué pour

une utilisation fiable et durable. Il ne nécessite aucun

entretien en dehors du nettoyage. Voir la section

“Méthode de nettoyage du moniteur àplasma”plus loin.

Le panneau à affichage plasma est constitué de fines

particules d’images (cellules) dont plus de 99,99%sont

actives. Certaines d’entre elles ne produisent pas de

lumière ou restent allumées.

ATTENTION

RISQUE D’ELECTROCUTION

NE PAS OUVRIR

Pour des raisons de sécurité et pour éviter

d’endommager l’appareil, lire attentivement les

instructions suivantes.

Pour éviter les risques d’éléctrocution et d’incendie:

1. Laisser suffisament d’espace autour de l’appareil pour

la ventilation et éviter toute augmentation excessive de

la température interne. Ne pas couvrir les évents ou

l’installer dans un endroit trop exigu.

MISE EN GARDE: AFIN DE REDUIRE LES RISQUES

D’ELECTRO-CUTION, NE PAS

DEPOSER LE COUVERCLE, IL N’Y A

AUCUNE PIECE UTILISABLE A

L’INTERIEUR DE CET APPAREIL. NE

CONFIER LES TRAVAUX D’ENTRETIEN

QU’A UN PERSONNEL QUALIFIE.

Ce symbole a pour but de prévenir l’utilisateur

de la présence d’une tension dangereuse, non

isolée se trouvant à l’intérieur de l’appareil.

Elle est d’une intensité suffisante pour

constituer un risque d’électrocution. Eviter le

contact avec les pièces à l’intérieur de cet

appareil.

Si vous installez l’appareil dans un espace clos,

assurezvous qu’il y ait suffisamment d’espace au dessus

pour permettre à l’air chaud de s’élever et de s’évacuer.

Si la température du moniteur devient excessive, la

protection contre les surchauffes entrera en action et

coupera l’alimentation. Dans ce cas, éteindre l’appareil

et débrancher le câble d’alimentation. Si la température

de la pièce dans laquelle se trouve le moniteur est

particulièrement élevée, déplacer celui-ci dans un endroit

plus frais et attendre environ 60 minutes qu’il refroidisse.

Si le problème persiste, prendre contact avec le revendeur

Marantz pour le service après-vente.

Ce symbole a pour but de prévenir l’utilisateur

de la présence d’importantes instructions

concernant l’entretien et le fonctionnement de

cet appareil. Par conséquent, elles doivent être

lues attentivement afin d’éviter des problèmes.

2. Ne pas raccorder la prise d’alimentation polarisée de ce

périphérique à une rallonge ou une prise murale si les

fiches ne peuvent pas être complètement insérées.

3. Ne pas exposer à L’eau ou à l’humidité.

4. Eviter d’endommager le cordon d’alimentation, et ne pas

modifier le cordon d’alimentation.

AVERTISSEMENT

AFIN DE REDUIRE LES RISQUES D’INCENDIE OU

D’ELECTROCUTION, NE PAS EXPOSER CETAPPAREIL

ALAPLUIE OUAL’HUMIDITE.AUSSI, NE PAS UTILISER

LA FICHE POLARISEE AVEC UN PROLONGATEUR OU

UNEAUTRE PRISE DE COURANT SAUF SI CES LAMES

PEUVENT ETRE INSEREES A FOND. NE PAS OUVRIR

LE COFFRET, DES COMPOSANTS HAUTETENSION SE

5. Débrancher le câble d’alimentation électrique pendant les

orages ou les longues périodes d’inactivité.

6. Ne pas ouvrir le coffret. Des composants de haute

tension se trouvent à l’intérieur. Si l’appareil est

endommagé de cette manière, la garantie devient

caduque. De plus, il y a risque d’électrocution.

7. Ne pas essayer d’intervenir ou de réparer l’appareil. Le

fabricant décline toute responsabilité en cas de blessure

corporelle ou de dégâts matériels résultant d’une opération

d’entretien quelconque effectuée par des personnes non

qualifiées ou résultant de l’ouverture du couvercle arrière.

Confier toute réparation à un centre de service agréé

Marantz.

TROUVENT

L’INTERIEUR. LAISSER

PERSONNEL QUALIFIE LE SOIN DE REPARER CET

APPAREIL.

Download from Www.Somanuals.com. All Manuals Search And Download.

Pour éviter des dommages et prolonger la durée de

service de l’appareil:

Méthode de nettoyage du moniteur à plasma:

1. Nettoyer le panneau avant et le cadre en procédant àl’aide

d’un chiffon doux et sec. Ne jamais utiliser de solvents

du type alcool ou diluant pour le nettoyage de ces surfaces.

2. Nettoyer les prises d’aération du plasma en procédant à

l’aide d’une brosse à poils doux fixée à un aspirateur.

3. Pour garantir la bonne ventilation du moniteur, nettoyer

les prises d’air tous les mois. Un nettoyage plus fréquent

peut s’avérer nécessaire selon les conditions

environnantes dans lesquelles le moniteur à plasma est

utilisé.

1. N’utiliser qu’une source d’alimentation de 120 V 50/

60 Hz CA. Le fait d’utiliser l’appareil en continu à des

tensions de ligne supérieures à 120 Volts CA réduit sa

durée de vie et risque de provoquer un incendie.

2. Manipuler l’appareil avec soin pendant son

déplacement et ne pas le faire tomber.

3. Eloigner l’appareil des endroits chauds, très poussiéreux

et exposés en plein soleil.

4. Eviter que des liquides et des petits objets métalliques

pénètrent à l’intérieur de l’appareil. En cas d’incident de

ce genre, débrancher le câble d’alimentation électrique

et confier le moniteur à un service après-vente agréé.

5. Ne pas frapper ou rayer la surface de la écran plasma,

car des défauts risquent de se produire sur la surface

de la écran plasma.

6. Pour un montage et une installation correcte, il est

fortement recommandé de faire appel à un revendeur

agréé et qualifié.

Pour éviter les risques de brûlage du luminophore, les

mesures suivantes sont recommandées:

Comme tous les périphériques d’affichage àbase luminophore

et tous les autres affichages gaz plasma, les moniteurs plasma

peuvent être sujets au brûlage du luminophore dans certaines

circonstances. Certaines conditions d’utilisation, telles que

l’affichage continu d’une image statique pour une durée

prolongée, peuvent causer le brûlage du luminophore si

aucune précaution n’est prise. Pour protéger votre

investissement dans ce moniteur à plasma, veuillez suivre

les directives et les conseils suivantes pour minimiser

l’occurence le marquage de l’écran:

7. Comme c’est le cas pour tout affichage à base de

phosphore (comme un moniteur CRT, par exemple), la

puissance de lumière baisse graduellement au cours de

la vie du Panneau d’Affichage à Plasma.

8. Pour éviter tout risque de sulfuration, il est fortement

conseillé de ne pas installer l’appareil dans un vestiaire,

un bain public ou un bain de source thermale.

• Assurez-vous de mettre en marche et d’utliser

l’économisateur d’écran chaque fois que c’est possible

lorsque vous l’utilisez avec une source d’entrée

d’ordinateur.

• Affichez une image en mouvement aussi souvent que

possible.

• Changer la position de l’affichage de menu de temps àautre.

• Coupez toujours l’alimentation lorsque vous avez terminé

d’utiliser la moniteur.

Si le moniteur est en usage continu ou longue durée, prenez

les mesures suivantes afin d’éviter l’occurence le brûlage

du luminophore:

• Abaissez le niveau de l’image (contraste, luminosité)

autant que possible, sans faire perdre la lisibilité de

l’image.

• Affichez une image avec de nombreuses couleurs et

graduations de couleur (par ex. des images

photographiques ou photo-réalistes).

• Créez un contenu d’image avec un contraste minimal

entre les zones sombres et les zones claires, par exemple,

des caractères blancs sur un fond noir. Utilisez des

couleurs complémentaires ou pastels le plus souvent

possible.

• Évitez d’afficher des images avec peu de couleurs et des

limites nettes et clairement définies entre les couleurs.

* Remarque:Le brûlage de l’écran n’est pas couvert

par la garantie.

Contactez Marantz Service Center pour d’autres procédures

recommandées qui conviendront le mieux au besoin de votre

appareil.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

How to Attach Options to the Plasma Monitor .... 1

Ventilation Requirements for enclosure mounting .......... 1

How to use the safety metal fittings and the screws for

safety metal fittings ................................................. 1

Image Adjust Settings Menu .................................... 22

Adjusting the Position, Size, Fine Picture, Picture Adj ....... 22

Option1 Settings Menu ........................................... 23

Setting the on-screen menu ........................................ 23

Setting the BNC connectors ....................................... 24

Checking the signal being transmitted to RGB1 terminal .... 24

Setting a computer image to the correct RGB

Part Names and Function .................................. 2

Front View .............................................................. 2

Rear View / Terminal Board ...................................... 3

Remote Control ........................................................ 4

Battery Installation and Replacement ........................... 5

Using the wired remote control mode .......................... 6

Operating Range .......................................................... 6

Handling the remote control......................................... 6

select screen ............................................................. 24

Setting high definition images to the suitable

screen size ................................................................ 25

Setting the Input Skip................................................. 25

Resetting to the default values.................................... 26

Option2 Settings Menu ........................................... 26

Setting the power management for computer images .......... 26

POWER/STANDBY indicator ................................... 27

Setting the picture to suit the movie ........................... 27

Reducing burn-in of the screen .................................. 27

Setting the gray level for the sides of the screen ......... 30

Setting the screen size for S1/S2 video input .............. 30

Setting the picture size for RGB input signals ............ 31

Setting the signal and black level for DVI signal ........ 31

Option3 Settings Menu ........................................... 32

Using the timer .......................................................... 32

Setting the power on mode........................................ 33

Enabling/disabling the front panel controls ................ 34

Enabling/disabling remote control wireless

transmission ............................................................. 34

Loop Out setting ........................................................ 35

ID number setting ...................................................... 35

Video Wall setting ...................................................... 36

Advanced OSM Settings Menu ................................ 39

Setting the menu mode .............................................. 39

Language Settings Menu ......................................... 40

Setting the language for the menus............................. 40

Color System Settings Menu .................................... 40

Setting the video signal format ................................... 40

Source Information Menu ........................................ 40

Checking the frequencies, polarities of input signals,

and resolution .......................................................... 40

Installation ...................................................... 7

Connecting Your PC or Macintosh Computer ............... 8

Connections with Equipment that have a Digital Interface......

Connecting Your Document Camera ........................... 8

Connecting Your VCR or Laser Disc Player.................. 8

Connecting Your DVD Player ..................................... 8

Pin Assignments and Signal Levels

for 15 pin RGB (Analog) ......................................... 9

Pin Configuration and Signal Levels

of the RGB 3 Connector (DVI Connector)................... 9

Creating a video wall ............................................. 10

Cable Management................................................ 10

Basic Operations............................................. 11

POWER ................................................................ 11

To turn the unit ON and OFF: .................................... 11

VOLUME .............................................................. 11

To adjust the sound volume:...................................... 11

MUTE ................................................................... 11

To cancel the sound:.................................................. 11

DISPLAY ................................................................ 11

To check the settings: ................................................. 11

DIGITAL ZOOM ..................................................... 11

AUTO ADJUST ...................................................... 11

To adjust the size or quality of the picture automatically .... 11

OFF TIMER ........................................................... 12

To set the off timer: ................................................... 12

To check the remaining time: ..................................... 12

To cancel the off timer: .............................................. 12

External Control ............................................. 41

Troubleshooting............................................. 42

WIDE Operations............................................. 13

Wide Screen Operation (manual) ........................... 13

When viewing videos or digital video discs .............. 13

Wide Screen Operation with Computer Signals ......... 14

When “PICTURE SIZE” is set to “OFF” .................. 14

OSM Controls.................................................. 15

Menu Operations ................................................... 15

Menu Tree ............................................................. 16

Picture Settings Menu.............................................. 18

Adjusting the picture .................................................. 18

Setting the picture mode according to the brightness

of the room .............................................................. 18

Reducing noise in the picture ..................................... 19

Setting the color temperature ..................................... 19

Adjusting the color to the desired level ...................... 19

Changing the Gamma Curve ...................................... 20

Making the Low Tone adjustments ............................ 20

Adjusting the colors ................................................... 21

Audio Settings Menu .............................................. 21

Adjusting the treble, bass and left/right balance

and audio input select ............................................... 21

Setting the allocation of the audio connectors ............ 22

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Attach Options to the Plasma Monitor

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

* While it is upright. (See Drawing A)

* As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the

monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

* Do not touch or hold the screen face when carrying the unit.

• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall

mount unit, Stand, etc.)

* See the inside of the cover page.

• For correct installation and mounting it is strongly recommended to use a trained, authorized

dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury

to the installer.

Product warranty does not cover damage caused by improper installation.

* Use only the mounting kit or stand provided by manufacturer and listed under Options.

Drawing A

Drawing B

Some models are equipped with

handles.

When installing or carrying, use the

handles attached to the upper back

of the display.

Ventilation Requirements for

enclosure mounting

To allow heat to disperse, leave space between surrounding

objects as shown on the diagram below when installing.

How to use the safety metal fittings

and the screws for safety metal

fittings

These are fittings for fastening the unit to a wall to prevent

tipping due to external shock when using the stand

(optional). Fasten the safety fittings to the holes in the

back of the monitor using the safety fitting mount screws.

* Safety metal fittings will differ according to the model.

Wall

50mm (2")

Screw hole

Wall

Screw or Hook etc.

(Not supplied)

Safty metal fittings

Screw for Safty metal

Wall

50mm (2")

fittings

Metal chain

(Not supplied)

Table Top

Download from Www.Somanuals.com. All Manuals Search And Download.

Part Names and Function

Front View

VOLUME

DOWN

INPUTSELECT

EXIT

POWER/STANDBY

MENU/ENTER

LEFT/

RIGHT/

VOLUME

DOWN

INPUTSELECT

/EXIT

POWER/STANDBY

MENU/ENTER

LEFT/

RIGHT/

q Power

t LEFT/– and RIGHT/+

Enlarges or reduces the image. Functions as the

Turns the monitor’s power on and off.

ᮤ

ᮣ

CURSOR (

(OSM) mode.

) buttons in the On-Screen Menu

w Remote sensor window

Receives the signals from the remote control.

y VOLUME DOWN and UP

e POWER/STANDBY indicator

Adjusts the volume. Functions as the CURSOR (▲/

▲) buttons in the On-Screen Menu (OSM) mode.

When the power is on ............................. Lights green.

When the power is in the standby mode ... Lights red.

* POWER/STANDBY letter is printed on model

PD6140 and PD5040 only.

u MENU/ENTER

Sets the On-Screen Menu (OSM) mode and displays

the main menu.

r INPUT SELECT / EXIT

Switches the input, in the following order.

The available inputs depend on the setting of “BNC

INPUT”.

→ VIDEO1 → VIDEO2 → VIDEO3 → HD/DVD/DTV

RGB/PC3 ← RGB/PC2 ← RGB/PC1←

RGB:

COMP.:

→VIDEO1 → VIDEO2 → VIDEO3 → HD1/DVD1/DTV1

RGB/PC2 ← RGB/PC1 ← HD2/DVD2/DTV2 ←

Functions as the EXIT buttons in the On-Screen Menu

(OSM) mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Rear View/ Terminal Board

A B

A AC IN

G RGB1 (mini D-Sub 15pin)

Connect the included power cord here.

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output. (see

page 10)

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the

EXT SPEAKER terminal and the

speaker wire to the EXT SPEAKER terminal on

(positive) speaker wire to the

H RGB3 (DVI 24pin)

(negative)

Connect a digital signal (TMDS) from a source with a

DVI output. (see page 8)

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

EXTERNAL CONTROL

This terminal is used when operating and controlling

the monitor externally (by external control).

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output (see page

10).

J REMOTE IN

Connect the remote cable* to the remote control’s

remote jack to obtain wired remote control.

D AUDIO1, AUDIO2, AUDIO3

K REMOTE OUT

These are audio input terminals.

Connect the remote cable* to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

The input is selectable. Set which video image to allot

them from the audio menu screen.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

* The 1/8 Stereo Mini cable must be purchased separately.

F RGB2/ DVD2/ HD2

RGB2:

You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source. (see page

24)

Download from Www.Somanuals.com. All Manuals Search And Download.

w RGB/PC

Press this button to select RGB/PC as the source.

Remote Control

The available sources depend on the setting of “BNC

INPUT”.

→ RGB/PC1 → RGB/PC2 → RGB/PC3

RGB:

→ RGB/PC1 → RGB/PC3

COMP. :

POWER

STANDBY

RGB/PC can also be selected using the INPUT

SELECT button on the monitor.

RGB/PC

DVD/HD

e DVD / HD

VIDEO

Press this button to select DVD/HD as the source.

The available sources depend on the setting of “BNC

INPUT”.

POSITION

/CONTROL

MENU/ENTER

HD/DVD/DTV

RGB:

→ HD1/DVD1/DTV1 → HD2/DVD2/DTV2

COMP.:

EXIT

POINTER

DVD/HD can also be selected using the INPUT

SELECT button on the monitor.

ZOOM

VOLUME

r VIDEO

Press this button to select VIDEO as the source.

→ VIDEO1 → VIDEO2 → VIDEO3

VIDEO can also be selected using the INPUT SELECT

button on the monitor.

MUTE

t MENU/ENTER

WIDE

DISPLAY

Press this button to access the OSM controls.

Press this button during the display of the main menu

to go to the sub menu.

OFF TIMER

ᮤ

ᮣ

y CURSOR (▲ / ▲ /

)

MULTI

SELECT

Use these buttons to select items or settings and to

adjust settings or switch the display patterns.

AUTO ADJUST

CLEAR

u EXIT

Press this button to exit the OSM controls in the main

menu. Press this button during the display of the sub

menu to return to the previous menu.

ID SELECT

i POINTER

Press this button to display the pointer.

o ZOOM (+ /–)

Enlarges or reduces the image.

! VOLUME (+ /–)

Adjusts the audio volume.

q POWER ON/STANDBY

! MUTE

Switches the power on/standby.

(This does not operate when POWER/STANDBY

indicator of the main unit is off.)

Mutes the sound.

! WIDE

Automatically detects the signal and sets the aspect

ratio.

Wide button is not active for all signals.

! DISPLAY

Displays the source settings on the screen.

! OFF TIMER

Activates the off timer for the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

! MULTI

Not functional for the models covered in this manual.

Battery Installation and Replacement

Insert the 2 “AAA” batteries, making sure to set them in

with the proper polarity.

! SELECT

Not functional for the models covered in this manual.

1.Press and open the cover.

! AUTO ADJUST

Press this button to adjust Fine Picture, Picture ADJ,

Position, and Contrast automatically, or to switch the

screen size to ZOOM mode automatically with the

superimposed caption displayed fully only when the

picture contains dark areas above and below the picture.

! ID SELECT

Set the ID number in the remote control. The remote

control can then be used only for a display with the

same ID number. When several displays are used

together they can be controlled individually.

2.Align the batteries according to the (+) and (–) indication

inside the case.

! CLEAR

Clears the number set by the ID SELECT button.

@ Remote control signal transmitter

Transmits the remote control signals.

@ Remote Jack

Insert the plug of the remote cable (The 1/8 Stereo

Mini cable) here when using the supplied remote

control in the wired condition.

3.Replace the cover.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the wired remote control mode

Connect the remote cable* to the remote control’s remote

jack and the “REMOTE IN” terminal on the monitor.

When the cable is connected, the mode automatically

switches to wired remote control. When the wired remote

control mode is used, the remote control can be operated

even if no batteries are loaded.

Operating Range

* Use the remote control within a distance of about 7 m/

23ft. from the front of the monitor’s remote control sensor

and at horizontal and vertical angles of up to approximately

30°.

* The remote control operation may not function if the

monitor’s remote control sensor is exposed to direct

sunlight or strong artificial light, or if there is an obstacle

between the sensor and the remote control.

POWER/STANDBY

Approx.

7m/23ft

Remote Control

Cable*

To Remote Jack

Handling the remote control

• Do not drop or mishandle the remote control.

• Do not get the remote control wet. If the remote control

gets wet, wipe it dry immediately.

• Avoid heat and humidity.

• When not using the remote control for a long period,

remove the batteries.

• Do not use new and old batteries together, or use different

types together.

* The 1/8 Stereo Mini cable must be purchased separately.

• Do not take apart the batteries, heat them, or throw them

into a fire.

• When using the remote control in the wireless condition,

be sure to unplug the remote cable from the REMOTE

IN terminal on the monitor.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

VCR or Laser Disc Player

VIDEO 1-3

To video inputs on

the plasma monitor

Document Camera

DVD Player

IBM VGA or Compatibles

Macintosh or Compatibles

(Desk top type)

Monitor adapter for

Macintosh

To Mini D-Sub 15 pin connector on the plasma monitor

Personal computer with a

digital signal output

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Your PC or Macintosh Computer

Connecting your PC or Macintosh computer to your plasma

monitor will enable you to display your computer’s screen

image for an impressive presentation. The plasma monitor

supports the signals described on page 7 of Model

Information.

Connecting Your Document Camera

You can connect your plasma monitor to a document

camera. To do so, simply:

1. Turn off the power to your plasma monitor and

document camera.

2. Use a standard video cable to connect your document

camera to the Video input on your plasma monitor.

To connect a PC, Macintosh or compatible graphics adapter,

simply:

3. Turn on the plasma monitor and the document camera.

1. Turn off the power to your plasma monitor and computer.

2. If your PC does not support SXGA/XGA/SVGA/VGA

you will need to install an SXGA/XGA/SVGA/VGA

graphics board. Consult your computer’s owner’s manual

for your SXGA/XGA/SVGA/VGA configuration. If you

need to install a new board, see the manual that comes

with your new graphics board for installation instructions.

Note: Refer to your document camera owner’s manual

for more information about your camera’s video output

requirements.

Connecting Your VCR or Laser Disc

Player

3. This plasma monitor provides signal compatibility up to

VESA 1600

1200 (UXGA). However, it is not

recommended to use this resolution due to image

readability on the monitor’s native pixel resolution panel.

Use common RCA cables (not provided) to connect your

VCR or laser disc player to your plasma monitor. To make

these connections, simply:

4. Use the signal cable to connect your PC or Macintosh

computer to the plasma monitor. For Macintosh, use the

monitor adapter to connect to your computer’s video port,

if necessary.

1. Turn off the power to your plasma monitor and VCR

or laser disc player.

2. Connect one end of your RCA cable to the video output

connector on the back of your VCR or laser disc player,

connect the other end to the Video input on your plasma

monitor. Use standard RCA audio patch cords to

connect the audio from your VCR or laser disc player

to your plasma monitor (if your VCR or laser disc player

has this capability). Be careful to keep your right and

left channel connections correct for stereo sound.

5. Turn on the plasma monitor and the computer.

6. If the plasma monitor goes blank after a period of inactivity,

it may be caused by a screen saver installed on the computer

you’ve connected to the plasma monitor.

When using a Macintosh with the plasma monitor, the

following four display standards are supported using the

Macintosh adapter :

3. Turn on the plasma monitor and the VCR or laser disc

player.

13" fixed mode

16" fixed mode

19" fixed mode

21" fixed mode

The 19" fixed mode is recommended for your monitor.

Note: Refer to your VCR or laser disc player owner’s

manual for more information about your equipment’s video

output requirements.

Connections with Equipment that

Connecting Your DVD Player

You can connect your plasma monitor to a DVD player.

To do so, simply:

have a Digital Interface

Connections can be made with equipment that is equipped

with a digital interface compliant with the DVI (Digital

Visual Interface) standard.

* Use a DVI 24-pin signal cable and the ferrite cores

(supplied) when making connections to the RGB3 (DVI)

connector of the main unit.

1. Turn off the power to your plasma monitor and DVD

player.

2. Use a component video cable to connect your DVD

player to the Y, Cb, and Cr inputs on your plasma

monitor.

Note that the RGB3 (DVI) terminal does not support analog

RGB input source.

Or use the DVD-player’s S-Video output. Use a

standard S-Video cable to connect to the S-Video input

on the plasma monitor.

Note:

1. Input TMDS signals conforming to DVI standards.

The TMDS input corresponds to 1 link.

3. Turn on the plasma monitor and the DVD player.

2. To maintain display quality, use a cable with a quality

prescribedbyDVIstandardsthatiswithin5metersinlength.

Download from Www.Somanuals.com. All Manuals Search And Download.

Pin Assignments and Signal Levels

for 15 pin RGB (Analog)

Pin Configuration and Signal of the

RGB 3 Connector (DVI Connector)

The unit is equipped with a type of connector commonly

used for digital.

(This cannot be used for an analog input.)

(TMDS can be used for one link only.)

15 14 13 12 11

RGB 3

Pin No.

Signal (Analog)

Red

Green or sync-on-green

Blue

10 11 12 13 14 15 16

17 18 19 20 21 22 23 24

No connection

Ground

Red ground

Green ground

Blue ground

No connection

Sync signal ground

No connection

Bi-directional DATA (SDA)

Horizontal sync or Composite sync

Vertical sync

Pin No.

Signal (Digital)

T.M.D.S Data 2 -

T.M.D.S Data 2 +

T.M.D.S Data 2 Shield

No connection

DDC Clock

DDC Data

No connection

T.M.D.S Data 1 -

T.M.D.S Data 1 +

T.M.D.S Data 1 Shield

No connection

+5V Power

Data clock

Ground

Hot Plug Detect

T.M.D.S Data 0 -

T.M.D.S Data 0 +

T.M.D.S Data 0 Shield

No connection

T.M.D.S Clock Shield

T.M.D.S Clock +

T.M.D.S Clock -

Download from Www.Somanuals.com. All Manuals Search And Download.

Creating a video wall

With buit-in matrix display capability, you can create a 2×2 or 3×3 video wall.

• Connect signal cables and remote cables as shown below.

Video signal

RGB/DVD/HD signal

BNC connector

OUT

VIDEO Signal

RGB signal/

RCA phono plug

DVD/HD signal

VIDEO Signal

OUT

RGB signal/

DVD/HD signal

Remote

control

OUT

Remote

control

Remote

control

Remote

control

Note:

1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.

When LOOP OUT is ON, do not connect an OUTPUT signal from another unit, that will place an extraordinary load on

the other unit and may damage it.

2. LOOP OUT can not be turned ON while signals are input to RGB1 terminal.

3. LOOP OUT can be turned ON while signals are input to RGB1 terminal if the POWER is switched ON.

Information

• To loop signals out to another plasma display, set the LOOP OUT to ON.

• To create a video wall, set the VIDEO WALL menu items properly.

• To connect monitors, please use a 1~2m (3.3~6.6 feet) BNC cable (any commercially available cable).

• If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially

available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

• Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024

768, 60Hz

signal.

• A distribution amplifier is particularly recommended when using a 9-screen video wall.

• From the second monitor onward, connections require a BNC-RCA conversion cable or connector, a mini D-Sub

15 pin cable-BNC (

5) cable or a conversion connector.

Cable Management

Using the cable clamps provided with the plasma display,

Back of the unit

bundle at the back of the unit the signal and audio cables

connected to the display.

* The cable clamp will differ according to the model.

mounting hooks/mounting holes

To attach

To detach

clamp

cables

mounting hook

To attach

To detach

clamp

cables

mounting hole

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Operations

POWER

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges

the picture.

To turn the unit ON and OFF:

1. Plug the power cord into an active AC power outlet.

1. Press the POINTER button to display the pointer. (

)

2. Press the Power button (on the unit).

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set.

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture.

The pointer will change to resemble a magnifying

glass. (

A press of the ZOOM- button will reduce the picture

and return it to its original size.

3. Press the POWER ON button (on the remote control)

to turn on the unit.

)

The monitor’s POWER/STANDBY indicator will light

up (green) when the unit is on.

To change the picture position:

Select the position with the LL

4. Press the POWER STANDBY button (on the remote

control) or the Power button (on the unit) to turn off

the unit.

ᮤ ᮣ

buttons.

2. Press the POINTER button to delete the pointer.

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set (only when turning off the

unit with the remote control).

AUTO ADJUST

To adjust the size or quality of the picture

automatically:

VOLUME

To adjust the sound volume:

Press the AUTO ADJUST button.

1. Press and hold the VOLUME

button (on the remote

Information

control or the unit) to increase to the desired level.

Ⅵ AUTO ADJUST ON setting

2. Press and hold the VOLUME button (on the remote

control or the unit) to decrease to the desired level.

When RGB (still picture) input

is selected ......Fine Picture, Picture ADJ, Position,

and Contrast will be adjusted

automatically.

MUTE

To cancel the sound:

Press the MUTE button on the remote control to cancel

When RGB (motion picture),

the sound; press again to restore.

VIDEO, or Y/Pb/Pr (component) input

is selected ......The screen size switches to ZOOM

mode automatically with the

superimposed caption displayed fully

only when the picture contains dark

areas above and below the picture.

DISPLAY

To check the settings:

1. The screen changes each time the DISPLAY button is

pressed.

2. If the button is not pressed for approximately three

seconds, the menu turns off.

Download from Www.Somanuals.com. All Manuals Search And Download.

To cancel the off timer:

OFF TIMER

To set the off timer:

1. Press the OFF TIMER button twice in a row.

2. The off timer is canceled.

The off timer can be set to turn the power off after 30, 60,

90 or 120 minutes.

OFF TIMER

1. Press the OFF TIMER button to start the timer at 30

minutes.

2. Press the OFF TIMER button to the desired time.

3. The timer starts when the menu turns off.

→ 30 → 60 → 90 → 120 → 0

Note:

OFF TIMER 30

After the power is turned off with the off timer ...

A slight current is still supplied to the monitor. When you

are leaving the room or do not plan to use the system for a

long period of time, turn off the power of the monitor.

To check the remaining time:

1. Once the off timer has been set, press the OFF TIMER

button once.

2. The remaining time is displayed, then turns off after a

few seconds.

3. When five minutes remain the remaining time appears

until it reaches zero.

OFF TIMER 28

Download from Www.Somanuals.com. All Manuals Search And Download.

WIDE Operations

ZOOM size screen

Wide Screen Operation (manual)

With this function, you can select one of six screen sizes.

When viewing videos or digital video discs

1. Press the WIDE button on the remote control.

2. Within 3 seconds ...

The picture is expanded in the horizontal and vertical

direction, maintaining the original proportions.

* Use this for theater size (wide) movies, etc.

Press the WIDE button again.

The screen size switches as follows:

→ NORMAL → FULL → STADIUM → ZOOM → 2.35:1 → 14:9

2.35:1 size screen

When a 720P or 1080I signal is input:

FULL ↔ 2.35:1

NORMAL size screen (4:3)

Original image

Information is lost on both sides.

The squeezed film image is expanded to fulfill the entire

screen at a ratio of 2.35:1. Black bands do not appear at

the top and bottom but information is lost on the left and

right margins.

• This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB

(525P or 625P signal from a scan converter).

* If black bands appear on the top and bottom in the full size

screen, select the 2.35:1 size screen to avoid phosphor burn-

in.

The normal size screen is displayed.

* The picture has the same size as video pictures with a

4 : 3 aspect ratio.

FULL size screen

14:9 size screen

The image is expanded in the horizontal direction.

* Images compressed in the horizontal direction (“squeezed

images”) are expanded in the horizontal direction and

displayed on the entire screen with correct linearity.

(Normal images are expanded in the horizontal direction.)

The image is displayed at a 14:9 aspect ratio.

* This feature is available when the input signal is video,

component (480I, 480P, 576I, 576P) or RGB (525Por 625P

signal from a scan converter).

STADIUM size screen

Note:

Do not allow the displayed in 4:3 mode for an extended

period. This can cause a phosphor burn-in.

The picture is expanded in the horizontal and vertical

directions at different ratios.

* Use this for watching normal video programs (4:3) with a

wide screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

FULL size screen

Wide Screen Operation with

Computer Signals

Switch to the wide screen mode to expand the 4 : 3 image

to fill the entire screen.

1.Press the WIDE button on the remote control.

2.Within 3 seconds ...

The image is expanded in the horizontal and vertical

direction.

Press the WIDE button again.

The screen size switches as follows:

→ NORMAL → FULL → ZOOM

ZOOM size screen

NORMAL size screen (4:3 or SXGA 5:4)

When wide signals are input.

The picture has the same size as the normal computer

image.

TRUE

FULL size screen

The image is true resolution.

FULL

The image is expanded in the horizontal direction.

ZOOM size screen

Information

When wide signals are input.

Ⅵ Supported resolution

FULL size screen

See page 7 of Model Information for details on the

display output of the various VESA signal standards

supported by the monitor.

Ⅵ “PICTURE SIZE” setting

When the setting of “PICTURE SIZE” is OFF, the size

of RGB-input pictures will be TRUE in place of

NORMAL.

When “PICTURE SIZE” is set to “OFF”

* This cannot be set in some models. “TRUE size” will not

be displayed in such cases.

The screen size switches as follows:

→ TRUE → FULL → ZOOM

Ⅵ When 852 (848) dot

480 line wide VGA*

signals with a vertical frequency of 60 Hz and

horizontal frequency of 31.7 (31.0) kHz are in-

put

Select an appropriate setting for RGB SELECT mode

referring to the“Table of Signals Supported” on page 7

of Model Information.

TRUE size screen (VGA, SVGA 4:3)

* “VGA”, “SVGA” and “SXGA” are registered

trademarks of IBM, Inc. of the United States.

Note:

Do not allow the displayed in 4:3 mode for an extended

period. This can cause a phosphor burn-in.

The image is true resolution.

Download from Www.Somanuals.com. All Manuals Search And Download.

OSM(On Screen Menu) Controls

5. The adjustments or the settings that are stored in

Menu Operations

The OSM window is displayed with respect to the

screen as shown on the diagram.

memory.

The change is stored until you change it again.

6. Repeat steps 2 – 5 to adjust an additional item, or press

the EXIT button on the remote control to return to the

main menu.

* Depending on the screen’s mode, the OSM may be

displayed differently.

In the explanation, the OSM section is shown close up.

Note:The main menu disappears by pressing the EXIT

button.

MAIN MENU

PICTURE

AUDIO

IMAGE ADJUST

OPTION1

ADVANCED OSM

SEL.

OFF

MENU/ENTER

EXIT EXIT

Information

Ⅵ Advanced menu mode

When “ADVANCED OSM” is set to “ON” in the main

menu (1/2), full menu items will be shown.

The following describes how to use the menus and the

selected items.

MAIN MENU

1 / 2

PICTURE

1. Press the MENU/ENTER button on the remote control

to display the MAIN MENU.

AUDIO

IMAGE ADJUST

OPTION1

OPTION2

MAIN MENU

1 / 2

OPTION3

PICTURE

ADVANCED OSM

SEL.

AUDIO

IMAGE ADJUST

OPTION1

MENU/ENTER

EXIT EXIT

ADVANCED OSM

SEL.

OFF

MENU/ENTER

EXIT EXIT

MAIN MENU

2 / 2

LANGUAGE

COLOR SYSTEM

SOURCE INFORMATION

SEL.

MENU/ENTER

EXIT EXIT

2. Press the cursor buttons LLL on the remote control to

highlight the menu you wish to enter.

3. Press the MENU/ENTER button on the remote control

to select a sub menu or item.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

NORMAL

OFF

SEL.

ADJ.

EXIT RETURN

4. Adjust the level or change the setting of the selected

ᮤ

ᮣ

item by using the cursor buttons

control.

on the remote

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Tree

:Shaded areas indicate the default value.

ᮤ

ᮣ

←→

: Press the or button to adjust. The default value is at the center.

:Menu items in a ruled box are available when the ADVANCED OSM is set to ON.

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

REFERENCE

PICTURE

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

←→

YES

BRIGHT/NORMAL/THEAT.1/THEAT.2/DEFAULT

OFF/NR-1/NR-2/NR-3

LOW/MID LOW/MID/HIGH

COLOR TEMP

WHITE BALANCE

GAIN RED

GAIN GREEN

GAIN BLUE

BIAS RED

BIAS GREEN

BIAS BLUE

RESET

←→

OFF←→ON

…

GAMMA

LOW TONE

COLOR TUNE

1←→2← →4

…

AUTO←→1← →3

RED

Y←→M

C←→Y

GREEN

BLUE

YELLOW

MAGENTA

CYAN

M←→C

G←→R

R←→B

B←→G

OFF←→ON

RESET

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

REFERENCE

AUDIO

BASS

TREBLE

BALANCE

AUDIO INPUT1

AUDIO INPUT2

AUDIO INPUT3

←→

L←→R

VIDEO 1-3 / HD/DVD 1-2 / RGB 1-3

YES

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

REFERENCE

IMAGE ADJUST

ASPECT MODE

V-POSITION

H-POSITION

V-HEIGHT

NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9

←→

—

YES

H-WIDTH

←→

AUTO PICTURE

FINE PICTURE*¹

PICTURE ADJ.*¹

OFF←→ON*²

←→

*²

←→

*²

YES

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

REFERENCE

OPTION1

OSM

DISPLAY OSM

OSM ADJ.

OSM ANGLE

OSM ORBITER

RGB←→COMP.

RGB

AUTO/STILL/MOTION/WIDE1/WIDE2/DTV

1080B/1035I/1080A

OFF←→ON

1← →6

H←→V

OFF←→ON

YES

—

YES

—

…

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

OFF←→ON

Download from Www.Somanuals.com. All Manuals Search And Download.

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

REFERENCE

OPTION2

PWR. MGT.

CINEMA MODE

LONG LIFE

OFF←→ON

PLE

YES

AUTO/LOCK 1/LOCK 2/LOCK 3

AUTO 1

AUTO 2

ORBITER

MANUAL

OFF

H-DOT/V-LINE/TIME

INVERSE

OFF

WORKING TIME/WAITING TIME

WHITE

SCREEN WIPER OFF

WORKING TIME/WAITING TIME/SPEED

SOFT FOCUS

OFF/1/2/3/4

…

GRAY LEVEL

S1/S2

PICTURE SIZE

DVI SET UP

0← →3← →15

AUTO←→OFF

OFF←→ON

PLUG/PLAY

BLACK LEVEL

PC←→STB/DVD*³

LOW←→HIGH*⁴

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

REFERENCE

OPTION3

TIMER

PRESENT TIME

DAYLIGHT SAIVING TIME OFF←→ON

DAY/HOUR/MINUTES

OFF

PROGRAM

YES

—

YES

—

YES

DATE/ON/OFF(HOUR, MINUTE)/INPUT/FUNCTION

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

ID NUMBER

LAST / VIDEO 1-3 / HD/DVD 1-2 / RGB 1-3

OFF←→ON

…

ALL←→1← →256

VIDEO WALL

DIVIDER

OFF/1/4/9

No.1← →No.4/No.7← →No.15

SPLIT←→BLANK

…

POSITION

DISP. MODE

AUTO ID

OFF←→ON

IMAGE ADJUST ASPECT MODE

NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9

V-POSITION

H-POSITION

V-HEIGHT

H-WIDTH

←→

OFF←→ON*²

AUTO PICTURE

FINE PICTURE*¹

←→

*²

YES

PICTURE ADJ.*¹

←→

*²

P. ON DELAY

PLE LINK

REPEAT TIMER

OFF←→ON

OFF

DIVIDER/SOURCE/WORK TIME

Main menu

Sub menu

Sub menu 2

Sub menu 3

Sub menu 4

RESET

REFERENCE

ADVANCED OSM OFF←→ON

LANGUAGE ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/

COLOR SYSTEM AUTO/3.58NTSC/4.43 NTSC/PAL/PAL 60/PAL-N/PAL-M/SECAM

YES

—

SOURCE INFORMATION

—

*1 Only when AUTO PICTURE is OFF

*2 RGB/PC only

*3 The default value is PC for model PD4220V.

*4 The default value is LOW for model PD4220V.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the picture mode according to the

brightness of the room

There are four picture modes that can be used effectively

according to the environment in which you are viewing

the display.

Picture Settings Menu

Adjusting the picture

The contrast, brightness, sharpness, color and tint can be

adjusted as desired.

Example: Adjusting the contrast

Example: Setting the “THEAT. 1” mode

1. On the MAIN MENU, select “PICTURE”, then press

the MENU/ENTER button.

1. On the MAIN MENU, select “PICTURE”, then press

the MENU/ENTER button.

The “PICTURE” screen appears.

2. Use the L and L buttons to select “CONTRAST”.

2. Use the L and L buttons to select “PICTURE

MODE”.

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

NORMAL

OFF

TINT

PICTURE MODE

NORMAL

OFF

SEL.

ADJ.

EXIT RETURN

SEL.

ADJ.

EXIT RETURN

ᮤ

ᮣ

and buttons to adjust the contrast.

3. Use the

3. To set to “THEAT. 1” ...

ᮤ

ᮣ

Use the and buttons to select “THEAT. 1”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

→ BRIGHT ↔ NORMAL ↔ THEAT. 1 ↔ THEAT. 2 ↔ DEFAULT ←

CONTRAST

ᮤ

ᮣ

* If neither the or button is pressed within 5 seconds,

the current setting is set and the previous screen

reappears.

THEAT. 1

PICTURE MODE

Note:If “CAN NOT ADJUST” appears ...

When trying to enter the PICTURE submenu, make sure

PICTURE MODE is not set to DEFAULT.

ᮤ

ᮣ

* If neither the or button is pressed within 5 seconds,

the current selection is set and the previous screen

reappears.

Information

Ⅵ Picture adjustment screen

Ⅵ Types of picture modes

CONTRAST .... Changes the picture’s white level.

BRIGHTNESS .. Changes the picture’s black level.

SHARPNESS .. Changes the picture’s sharpness.

Adjusts picture detail of VIDEO

THEAT. 1, 2......Set this mode when watching video in

a dark room.

This mode provides darker, finer

pictures, like the screen in movie

theaters.

display.

COLOR ...........Changes the color density.

TINT ................Changes the picture’s tint. Adjust for

natural colored skin, background, etc.

For a darker image, select THEAT. 2.

NORMAL ......... Set this mode when watching video in

a bright room.

This mode provides dynamic pictures

with distinct differences between light

and dark sections.

Ⅵ Adjusting the computer image

Only the contrast and brightness can be adjusted when

a computer signal is connected.

BRIGHT ...........This mode provides brighter pictures

than NORMAL.

DEFAULT.........Use this to reset the picture to the

factory default settings.

Ⅵ Restoring the factory default settings

Select “DEFAULT” under the “PICTURE MODE”

settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

Reducing noise in the picture

Use these settings if the picture has noise due to poor

reception or when playing video tapes on which the picture

quality is poor.

Setting the color temperature

Use this procedure to set color tone produced by the plasma

display.

Example: Setting “HIGH”

Example: Setting “NR-3”

1. On the MAIN MENU, select “PICTURE”, then press

the MENU/ENTER button.

1. On the MAIN MENU, select “PICTURE”, then press

the MENU/ENTER button.

The “PICTURE” screen appears.

2. Use the L and L buttons to select “COLOR TEMP.”.

2. Use the L and L buttons to select “NR”.

ᮤ

ᮣ

3. Use the and buttons to select “HIGH”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

PICTURE

1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

→ LOW ↔ MID LOW ↔ MID ↔ HIGH ←

TINT

* See below to set “WHITE BALANCE”.

PICTURE MODE

NORMAL

OFF

PICTURE

COLOR TEMP.

2 / 2

SEL.

ADJ.

EXIT RETURN

HIGH

GAMMA

LOW TONE

COLOR TUNE

AUTO

ᮤ

ᮣ

3. Use the

and

buttons to select “NR-3”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

SEL.

ADJ.

EXIT RETURN

→ OFF ↔ NR-1 ↔ NR-2 ↔ NR-3 ←

ᮤ

ᮣ

* If neither the or button is pressed within 5 seconds,

the current selection is set and the previous screen reappears.

Information

Ⅵ Setting the color temperature

LOW ................Redder

MID LOW ......... Slightly redder

MID ................... Standard (slightly bluer)

HIGH ...............Bluer

NR-3

ᮤ

ᮣ

* If neither the or button is pressed within 5 seconds,

the current selection is set and the previous screen

reappears.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory defaults.

Information

Ⅵ NR

Adjusting the color to the desired level

Use this procedure to adjust the white balance for each

color temperature to achieve the desired color quality.

* “NR” stands for Noise Reduction.

* This function reduces noise in the picture.

Example: Adjusting the “GAIN RED” of “HIGH” color

temperature

Ⅵ Types of noise reduction

There are three types of noise reduction. Each has a

different level of noise reduction.

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

The effect becomes stronger as the number increases

(in the order NR-1 → NR-2 → NR-3).

OFF ...............Turns the noise reduction function off.

Perform Steps 1-3 of COLOR TEMP., then...

4. Press the MENU/ENTER button.

The “WHITE BALANCE” screen appears.

5. Use the L and L buttons to select “GAIN RED”.

WHITE BALANCE

COLOR TEMP. HIGH

GAIN RED

GAIN GREEN

GAIN BLUE

BIAS RED

BIAS GREEN

BIAS BLUE

RESET

SEL.

OFF

EXIT RETURN

ADJ.

Download from Www.Somanuals.com. All Manuals Search And Download.

ᮤ

ᮣ

6. Adjust the white balance using the and buttons.

Making the Low Tone adjustments

This feature allows more detailed tone to be reproduced

especially in the dark area.

Example: Setting “2”

Set “ADVANCED OSM” to “ON” in the MAIN MENU

(1/2), then perform the following operations.

GAIN RED

1. On the MAIN MENU, select “PICTURE”, then press

the MENU/ENTER button.

ᮤ

ᮣ

* If neither the or button is pressed within 5 seconds,

the current setting is set and the previous screen reappears.

The “PICTURE” screen appears.

2. Use the L and L buttons to select “LOW TONE”.

Information

Ⅵ Adjusting the white balance

GAIN R/G/B ..... White balance adjustment for signal

level

BIAS R/G/B ..... White balance adjustment for black

level

ᮤ

ᮣ

3. Use the and buttons to select “2”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

→ AUTO ↔ 1 ↔ 2 ↔ 3 ←

RESET ............Resets settings to the factory default

PICTURE

COLOR TEMP.

2 / 2

ᮤ

ᮣ

values. Use and buttons to select

“ON”, then press the MENU/ENTER

button.

MID

GAMMA

LOW TONE

COLOR TUNE

Ⅵ Restoring the factory default settings

Select “RESET” under the WHITE BALANCE menu.

SEL.

ADJ.

EXIT RETURN

Changing the Gamma Curve

This feature adjusts the brightness of the midtone areas

while keeping shadows and highlights unchanged.

Information

Ⅵ LOW TONE settings

Example: Setting “3”

AUTO .......Will automatically appraise the picture and

make adjustments.

1 ...............Will apply the dither method suitable for

still pictures.

2 ...............Will apply the dither method suitable for

motion pictures.

3 ...............Will apply the error diffusion method.

Set “ADVANCED OSM” to “ON” in the MAIN MENU

(1/2), then perform the following operations.

1. On the MAIN MENU, select “PICTURE”, then press

the MENU/ENTER button.

The “PICTURE” screen appears.

2. Use the L and L buttons to select “GAMMA”.

Ⅵ Restoring the factory default settings

ᮤ

ᮣ

3. Use the and buttons to select “3”.

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory defaults.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

→ 1 ↔ 2 ↔ 3 ↔ 4 ←

PICTURE

COLOR TEMP.

2 / 2

MID

GAMMA

LOW TONE

COLOR TUNE

AUTO

SEL.

ADJ.

EXIT RETURN

Information

Ⅵ GAMMA settings

The picture becomes darker as the number increases

(in the sequence of 1, 2, 3, 4).

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory defaults.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the colors

Audio Settings Menu

Use this procedure to adjust hue and color density for red,

green, blue, yellow, magenta and cyan.

You can accentuate the green color of trees, the blue of

the sky, etc.

Adjusting the treble, bass and left/right

balance and audio input select

The treble, bass and left/right balance can be adjusted to

suit your tastes.

Example: Adjusting the color tune for blue

Example: Adjusting the bass

Set “ADVANCED OSM” to “ON” in the MAIN MENU

(1/2), then perform the following operations.

1. On the MAIN MENU, select “AUDIO”, then press

the MENU/ENTER button.

1. On the MAIN MENU, select “PICTURE”, then press

the MENU/ENTER button.

The “AUDIO” screen appears.

2. To adjust the bass ...

The “PICTURE” screen appears.

Use the L and L buttons to select “BASS”.

2. Use the L and L buttons to select “COLOR TUNE”,

then press the MENU/ENTER button.

ᮤ

ᮣ

3. Adjust the bass using the and buttons.

AUDIO

BASS

The “COLOR TUNE” screen appears.

TREBLE

3. Use the L and L buttons to select “BLUE”.

BALANCE

AUDIO INPUT1

AUDIO INPUT2

AUDIO INPUT3

VIDEO1

HD/DVD1

RGB1

ᮤ

ᮣ

4. Adjust using the and buttons.

COLOR TUNE

RED

GREEN

BLUE

SEL.

ADJ.

EXIT RETURN

YELLOW

MAGENTA

CYAN

To continue adjusting the audio ...

Repeat from step 2.

RESET

OFF

SEL.

ADJ.

EXIT RETURN

Note :If “CAN NOT ADJUST” appears...

Set “AUDIO INPUT” on the AUDIO menu correctly.

ᮤ

ᮣ

* If neither the or button is pressed within 5 seconds,

the current selection is set and the previous screen

reappears.

Information

To continue making other adjustments...

Ⅵ Audio settings menu

Repeat from step 3.

BASS ..............Controls the level of low frequency

Information

sound.

TREBLE ..........Controls the level of high frequency

sound.

BALANCE ....... Controls the balance of the left and

right channels.

Ⅵ COLOR TUNE settings

RED ................Makes red’s adjustment

GREEN ...........Makes green’s adjustment

BLUE...............Makes blue’s adjustment

YELLOW .........Makes yellow’s adjustment

MAGENTA ......Makes magenta’s adjustment

CYAN ..............Makes cyan’s adjustment

RESET ............Resets settings to the factory default

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

ᮤ

ᮣ

value. Use and buttons to select

“ON”, then press the MENU/ENTER

button.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the allocation of the audio connectors

Setting the AUDIO 1, 2, and 3 connectors to the desired

input.

Image Adjust Settings Menu

Adjusting the Position, Size, Fine Picture, Picture Adj

The position of the image can be adjusted and flickering

of the image can be corrected.

Example: Setting “AUDIO INPUT1” to “VIDEO 2”

Example:Adjusting the vertical position in the normal

mode

1. On the MAIN MENU, select “AUDIO”, then press the

MENU/ENTER button.

The “AUDIO” screen appears.

1. On the MAIN MENU, select “IMAGEADJUST”, then

press the MENU/ENTER button.

2. Use the L and L buttons to select “AUDIO INPUT1”.

The “IMAGE ADJUST” menu appears.

3. To set the AUDIO INPUT1 to “VIDEO2”...

Default settings (when RGB/PC is selected)

ᮤ

ᮣ

Use the and buttons to select “VIDEO2”.

IMAGE ADJUST

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

The available sources depend on the setting of “BNC

ASPECT MODE

V-POSITION

H-POSITION

V-HEIGHT

NORMAL

H-WIDTH

INPUT”.

AUTO PICTURE

FINE PICTURE

PICTURE ADJ.

SEL.

OFF

→ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ↔ HD/DVD1←

→RGB3 ↔ RGB2 ↔ RGB1 ←

→ VIDEO1 ↔ VIDEO2 ↔ VIDEO3↔ HD/DVD1←

RGB:

ADJ.

EXIT RETURN

* The settings on the IMAGE ADJUST menu are not

preset at the factory.

COMP.:

→RGB3 ↔ RGB1 ↔ HD/DVD2 ←

To select a mode ...

AUDIO

BASS

ᮤ

ᮣ

Use the and buttons to select a mode.

TREBLE

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

BALANCE

AUDIO INPUT1

AUDIO INPUT2

AUDIO INPUT3

VIDEO2

HD/DVD1

RGB1

NORMAL ↔ FULL

* The mode can also be switched by pressing the “WIDE”

button on the remote control.

SEL.

ADJ.

EXIT RETURN

2. To adjust the vertical position ...

Information

Use the L and L buttons to select “V-POSITION”.

Ⅵ AUDIO INPUT

IMAGE ADJUST

ASPECT MODE

V-POSITION

H-POSITION

V-HEIGHT

NORMAL

A single audio input cannot be selected as the audio

channel for more than one input terminal.

H-WIDTH

Ⅵ Restoring the factory default settings

AUTO PICTURE

FINE PICTURE

PICTURE ADJ.

SEL.

OFF

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

ADJ.

EXIT RETURN

ᮤ

ᮣ

3. Adjust using the and buttons.

V-POSITION

ᮤ

ᮣ

* If neither the or button is pressed within 5 seconds,

the current setting is set and the previous screen

reappears.

To continue making other computer image

adjustments ...

Repeat from step 2.

Download from Www.Somanuals.com. All Manuals Search And Download.

Option1 Settings Menu

Setting the on-screen menu

This sets the position of the menu, the display format

Information

Ⅵ When “AUTO PICTURE” is “OFF”

(horizontal or vertical) etc.

IMAGE ADJUST

Example: Turning the DISPLAY OSM off

ASPECT MODE

V-POSITION

H-POSITION

V-HEIGHT

FULL

1. On the MAIN MENU, select “OPTION1”, then press

the MENU/ENTER button.

H-WIDTH

AUTO PICTURE

FINE PICTURE

PICTURE ADJ.

SEL.

OFF

The “OPTION1” menu appears.

ADJ.

EXIT RETURN

2. Use the L and L buttons to select “OSM”, then press

the MENU/ENTER button.

When Auto Picture is off, the Fine Picture and the

Picture ADJ. items are displayed so that you can adjust

them.

The “OSM” menu appears.

3. Use the L and L buttons to select “DISPLAY OSM”.

4. To set the DISPLAY OSM to “OFF”...

Ⅵ Adjusting the Auto Picture

ᮤ

ᮣ

Use the and buttons to select “OFF”.

ON...................The Picture ADJ., Fine Picture and

Position adjustments are made

automatically.

Not available for digital ZOOM.

OFF .................The Picture ADJ., Fine Picture and

Position adjustments are made

manually.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

ON ↔ OFF

OSM

DISPLAY OSM

OSM ADJ.

OFF

OSM ANGLE

OSM ORBITER

OFF

* If FINE PICTURE won’t be adjusted, set Auto Picture

to OFF and adjust manually.

SEL.

ADJ.

EXIT RETURN

Ⅵ Adjusting the position of the image

V-POSITION ...Adjusts the vertical position of the

image.

H-POSITION ... Adjusts the horizontal position of the

image.

V-HEIGHT ....... Adjusts the vertical size of the image.

(Except for STADIUM mode)

H-WIDTH ......... Adjusts the horizontal size of the

image. (Except for STADIUM mode)

FINE PICTURE*.. Adjusts for flickering.

PICTURE ADJ.* ... Adjusts for striped patterns on the

image.

Information

Ⅵ DISPLAY OSM settings

ON............The on-screen menu appears.

OFF ..........The on-screen menu does not appear.

If you press the DISPLAY button on the remote control

for more than 3 seconds the main menu will appear

and can be set (although it is not ON).

Ⅵ OSM ADJUST settings

Adjusts the position of the menu when it appears on

the screen.

The position can be set between 1 to 6.

* The PictureADJ. and Fine Picture features are available

only when the “Auto Picture” is off.

* TheAUTO PICTURE, FINE PICTURE and PICTURE

ADJ. are available only for RGB signals.

But, these features are not available for moving pictures

on VIDEO, HD/DVD or RGB.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults except for Auto Picture.

Ⅵ OSM ANGLE settings

Sets the display format (landscape “H” or portrait “V”).

When the unit is installed vertically set the OSM

ANGLE at “V”.

“H”

OPTION1

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

RGB

AUTO

1080B

OFF

SEL.

MENU/ENTER

EXIT RETURN

Download from Www.Somanuals.com. All Manuals Search And Download.

OPTION1

“V”

Checking the signal being transmitted to

RGB1 terminal

OSM

BNC INPUT

RGB

D-SUB INPUT

RGB

RGB SELECT

Use this to confirm the signal being transmitted to the

RGB1 terminal.

AUTO

HD SELECT

1080B

OFF

INPUT SKIP

ALL RESET

OFF

It is set to RGB and can not be adjusted.

1024

768

SEL.

MENU/ENTER

EXITRETURN

OPTION1

1 / 3

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

RGB

AUTO

1080B

OFF

CAN NOT ADJUST

Ⅵ OSM ORBITER settings

ON........ The position of the menu will be shifted by

eight dots each time OSM is displayed.

OFF ...... OSM will be displayed at the same position.

Setting a computer image to the correct RGB

select screen

With the computer image, select the RGB Select mode

for a moving image such as (video) mode, wide mode or

digital broadcast.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults except for Auto Picture.

Example: Setting the “RGB SELECT” mode to

“MOTION ”

1. On the MAIN MENU, select “OPTION1”, then press

the MENU/ENTER button.

Setting the BNC connectors

Select whether to set the input of the 5 BNC connectors to

RGB and component.

The “OPTION1” screen appears.

2. Use the L and L buttons to select “RGB SELECT”.

Example: Set the BNC INPUT mode to “COMP.”

3. To set the RGB select mode to “MOTION” ...

1. On the MAIN MENU, select “OPTION1”, then press

the MENU/ENTER button.

ᮤ

ᮣ

Use the and buttons to select “MOTION”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

The “OPTION1” screen appears.

2. Use the L and L buttons to select “BNC INPUT”.

→ AUTO ↔ STILL ↔ MOTION ↔ WIDE1 ↔ WIDE2 ↔ DTV ←

3. To set the BNC INPUT mode to “COMP.”...

OPTION1

1 / 3

ᮤ

ᮣ

Use the and buttons to select “COMP.”.

OSM

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

RGB

MOTION

1080B

OFF

RGB ↔ COMP.

1 / 3

OFF

OPTION1

OSM

SEL.

ADJ.

EXIT RETURN

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

COMP.

RGB

AUTO

1080B

OFF

SEL.

ADJ.

EXIT RETURN

Information

Ⅵ BNC INPUT Settings

RGB .........Use the 5BNC terminals for RGB input.

COMP.......Use the 3BNC terminals for component

input.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

Download from Www.Somanuals.com. All Manuals Search And Download.

Information

Ⅵ RGB SELECT modes

Ⅵ HD SELECT modes

One of these 6 modes must be selected in order to

display the following signals correctly.

AUTO ..............Select the suitable mode for the

specifications of input signals as

listed in the table “Computer input

signals supported by this system” on

page 7 of Model Information.

These 3 modes are not displayed in correct image

automatically.

1080B ............... Standard digital broadcasts

1035I ...............Japanese “High Vision” signal format

1080A ............... Special Digital broadcasts (for

example : DTC100)

STILL ..............To display VESA standard signals.

(Use this mode for a still image from

a computer.)

MOTION..........The video signal (from a scan

converter) will be converted to RGB

signals to make the picture more

easily viewable. (Use this mode for a

motion image from a computer.)

Setting the Input Skip

When this is ON, signals which are not present will be

skipped over and only pictures whose signals are being

transmitted will be displayed.

This setting is valid only for the INPUT SELECT button

on the unit.

Example: Set to “ON”

1. On the MAIN MENU, select “OPTION1”, then press

the MENU/ENTER button.

WIDE1.............When an 852 dot

480 line signal

with a horizontal frequency of

31.7kHz is input, the image may be

compressed horizontally. To prevent

this, set RGB SELECT to WIDE1.

The “OPTION1” screen appears.

2. Use the L and L buttons to select “INPUT SKIP”.

3. To set the INPUT SKIP mode to “ON”...

WIDE2.............When an 848 dot

480 line signal

with a horizontal frequency of 31.0

kHz is input, the image may be

compressed horizontally. To prevent

this, set RGB SELECT to WIDE2.

ᮤ

ᮣ

Use the and buttons to select “ON”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

OFF ↔ ON

DTV .................Set this mode when watching digital

broadcasting (480P).

See page 7 of Model Information for the details of the

above settings.

OPTION1

1 / 3

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

RGB

AUTO

1080B

Ⅵ Restoring the factory default settings

OFF

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

SEL.

ADJ.

EXIT RETURN

Information

Ⅵ INPUT SKIP settings

Setting high definition images to the suitable

screen size

Use this procedure to set whether the number of vertical

OFF ........... Regardless of the presence of the signal,

scan and display all signals.

ON ............. If no input signal is present, skip that

signal.

lines of the input high definition image is 1035 or 1080.

Example: Setting the “1080B” mode to “1035I”

* “SETTING NOW” will appear during the input search.

1. On the MAIN MENU, select “OPTION1”, then press

the MENU/ENTER button.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

The “OPTION1” screen appears.

2. Use the L and L buttons to select “HD SELECT”.

3. To set the HD SELECT mode to “1035I” ...

ᮤ

ᮣ

Use the and buttons to select “1035I”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

→1080B ↔ 1035I ↔ 1080A ←

OPTION1

1 / 3

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

RGB

AUTO

1035

OFF

SEL.

ADJ.

EXIT RETURN

Download from Www.Somanuals.com. All Manuals Search And Download.

Resetting to the default values

Option2 Settings Menu

Use these operations to restore all the settings (PICTURE,

AUDIO, IMAGE ADJUST, OPTION1~3, etc) to the

factory default values.

Setting the power management for computer

images

This energy-saving (power management) function

automatically reduces the monitor’s power consumption

if no operation is performed for a certain amount of time.

Refer to page 16 for items to be reset.

1. On the MAIN MENU, select “OPTION1”, then press

the MENU/ENTER button.

Example: Turning the power management function on

The “OPTION1” screen appears.

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

2. Use the ▲ and ▲ buttons to select “ALL RESET”.

OPTION1

1 / 3

1. On the MAIN MENU, select “OPTION2”, then press

the MENU/ENTER button.

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

RGB

AUTO

1080B

OFF

The “OPTION2” screen appears.

2. Use the ▲ and ▲ buttons to select “PWR. MGT.”.

OFF

3. To turn the power management function on ...

SEL.

ADJ.

EXIT RETURN

ᮤ

ᮣ

Use the and buttons to select “ON”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

ᮤ

ᮣ

3. Use the and buttons to select “ON”, then press the

MENU/ENTER button.

ON ↔ OFF

OPTION1

1 / 3

OPTION2

POWER MGT.

2 / 3

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

RGB

AUTO

1080B

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

OFF

SEL.

MENU/ENTER

EXIT RETURN

SEL.

ADJ.

EXIT RETURN

ALL RESET

Information

Ⅵ Power management function

SETTING NOW

* The power management function automatically reduces

the monitor’s power consumption if the computer’s

keyboard or mouse is not operated for a certain amount

of time. This function can be used when using the

monitor with a computer.

When the “SETTING NOW” screen disappears, then

all the settings are restored to the default values.

* If the computer’s power is not turned on or if the

computer and selector tuner are not properly connected,

the system is set to the off state.

* For instructions on using the computer’s power

management function, refer to the computer’s operating

instructions.

Ⅵ Power management settings

ON........ In this mode the power management function

is turned on.

OFF ...... In this mode the power management function

is turned off.

Ⅵ Power management function and POWER/

STANDBY indicator

The POWER/STANDBY indicator indicates the status

of the power management function. See page 27 for

indicator status and description.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

Download from Www.Somanuals.com. All Manuals Search And Download.

POWER/STANDBY indicator

Reducing burn-in of the screen

Power

POWER/

Power

management

operating status

Description

Turning the picture

back on

The brightness of the screen, the position of the picture,

positive/negative mode and screen wiper are adjusted to

reduce burn-in of the screen.

management STANDBY

mode

indicator

Green

Not activated.

Activated.

Horizontal and vertical Picture already on.

synchronizing signals

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

are present from the

computer.

Off

Red

Horizontal and/or Operate the keyboard or

vertical synchronizing mouse. The picture

signals are not sent reappears.

1. On the MAIN MENU, select “OPTION2”, then press

the MENU/ENTER button.

from the computer.

The “OPTION2” screen appears.

Setting the picture to suit the movie

2. Use the ▲ and ▲ buttons to select “LONG LIFE”, then

press the MENU/ENTER button.

The film image is automatically discriminated and

projected in an image mode suited to the picture.

[NTSC, PAL, PAL60, 480I (60Hz), 525I (60Hz), 576I

(50Hz), 625I (50Hz), 1035I (60Hz), 1080I (60Hz) only]

The “LONG LIFE” screen appears.

LONG LIFE

PLE

AUTO

OFF

Example: Setting the “CINEMA MODE” to “OFF”

ORBITER

INVERSE

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

SCREEN WIPER

SOFT FOCUS

1. On the MAIN MENU, select “OPTION2”, then press

the MENU/ENTER button.

SEL.

ADJ.

EXIT RETURN

The “OPTION2” screen appears.

ᮤ

ᮣ

3. Set the LONG LIFE mode using ▲▲ and buttons.

See page 27 to set PLE.

2. Use the ▲ and ▲ buttons to select “CINEMA MODE”.

See page 28 to set ORBITER.

3. To set the CINEMA MODE to “OFF” ...

See page 28 to set INVERSE.

ᮤ

ᮣ

Use the and buttons to select “OFF”.

See page 29 to set SCREEN WIPER.

See page 30 to set SOFT FOCUS.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

ON ↔ OFF

Information

OPTION2

POWER MGT.

2 / 3

Ⅵ Restoring the factory default settings

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

OFF

SEL.

ADJ.

EXIT RETURN

PLE (Peak Luminance Enhancement)

Use this to activate the brightness limiter.

Example: Setting “PLE” to “LOCK1”

Information

Ⅵ CINEMA MODE

Perform Steps 1-2 of LONG LIFE, then...

ON...................Automatic discrimination of the

image and projection in cinema mode.

OFF ................... Cinema mode does not function.

3. Use the ▲ and ▲ buttons to select “PLE”.

ᮤ

ᮣ

4. Use the and buttons to select “LOCK1”.

Ⅵ Restoring the factory default settings

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

→AUTO ↔ LOCK1 ↔ LOCK2 ↔ LOCK3←

LONG LIFE

PLE

LOCK1

OFF

ORBITER

INVERSE

OFF

SCREEN WIPER

SOFT FOCUS

OFF

SEL.

ADJ.

EXIT RETURN

Information

Ⅵ PLE settings

AUTO ..............The brightness of the screen is

adjusted automatically to suit the

picture quality.

Download from Www.Somanuals.com. All Manuals Search And Download.

LOCK1, 2, 3 ....Sets maximum brightness.

The brightness level decreases in the

• H-DOT

→1 DOT ↔ 2 DOT ↔ ..... ↔ 19 DOT ↔ 20 DOT←

order of LOCK 1, 2, 3. LOCK 3

provides minimum brightness.

• V-LINE

→1 LINE ↔ 2 LINE ↔ ..... ↔ 19 LINE ↔ 20 LINE←

ORBITER

• TIME

Use this to set the picture shift.

→1 M ↔ 2 M ↔ 3 M ↔ 4 M ↔ 5 M←

Example: Setting “ORBITER” to “AUTO1”

Perform Steps 1-2 of LONG LIFE, then...

ORBITER

H-DOT

V-LINE

TIME

2 DOT

4 LINE

3 M

3. Use the ▲ and ▲ buttons to select “ORBITER”.

ᮤ

ᮣ

4. Use the and buttons to select “AUTO1”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

SEL.

ADJ.

EXIT RETURN

→OFF ↔ AUTO1 ↔ AUTO2 ↔ MANUAL←

Information

LONG LIFE

PLE

AUTO

AUTO1

OFF

Ⅵ ORBITER Function settings

ORBITER

INVERSE

H-DOT..........Moves from 1 to 20 dots in the

horizontal direction.

SCREEN WIPER

SOFT FOCUS

OFF

V-LINE..........Moves from 1 to 20 lines in the vertical

direction.

SEL.

ADJ.

EXIT RETURN

TIME ............Interval of 1~5 minutes (1 horizontal

dot or 1 vertical line per interval).

Information

Ⅵ ORBITER settings

OFF ..............Orbiter mode does not function.

INVERSE

Use this to set the inverse mode or to display a white

screen.

This is the default setting when RGB is

input.

Example: Setting “INVERSE” to “WHITE”

AUTO1 .........The picture moves around the screen

intermittently, making the picture

smaller. This is the default setting when

a Video or a DVD/HD/DTV singnal is

input. Set to “OFF” when these signals

are not used.

AUTO2 .........The picture moves around the screen

intermittently, making the picture

bigger.

Perform Steps 1-2 of LONG LIFE, then...

3. Use the ▲ and ▲ buttons to select “INVERSE”.

ᮤ

ᮣ

4. Use the and buttons to select “WHITE”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

→OFF ↔ ON ↔ WHITE←

MANUAL ......User can adjust the orbiter function

(Horizontal Dot, Vertical Line and

Time) manually.

LONG LIFE

PLE

AUTO

OFF

ORBITER

INVERSE

WHITE

OFF

SCREEN WIPER

SOFT FOCUS

See the following explanation.

OFF

* When a Video or a DVD/HD/DTV singnal is input, the

AUTO1 and 2 functions will affect only the moving

picture and will not make the screen smaller or bigger.

SEL.

ADJ.

EXIT RETURN

Information

Ⅵ INVERSE Settings

Adjust the ORBITER function manually

Set the amount of shift and the time between movement.

ON......... The picture is displayed alternately between

positive image and negative image.

Example: Setting so that the picture moves 2 dots

horizontally and 3 lines vertically every 3 minutes.

You can set the time by pressing the MENU/

ENTER button while “ON” is set.

Perform Steps 1-3 of ORBITER, then...

OFF ....... Inverse mode does not function.

WHITE ...The entire screen turns white.

You can set the time by pressing the MENU/

ENTER button while “ON” is set.

ᮤ

ᮣ

4. Use the and buttons to select “MANUAL”, then

press the MENU/ENTER button.

THE “ORBITER” screen appears.

ᮤ

ᮣ

5. Adjust the items using the ▲▲ and buttons.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the time for INVERSE/WHITE

SCREEN WIPER

Set a time duration.

When this is set to ON, a white vertical bar moves

repeatedly from the left and of the screen to the right end

at a constant speed.

Example: Setting to that the INVERSE mode starts

in 2 hours and proceeds for one hour and a half.

Example: Setting “SCREEN WIPER” to “ON”

Perform Steps 1-3 of INVERSE, then...

Perform Steps 1-2 of LONG LIFE, then...

ᮤ

ᮣ

4. Use the and buttons to select “ON”, then press the

MENU/ENTER button.

3. Use the ▲ and ▲ buttons to select “SCREEN WIPER”.

THE “INVERSE/WHITE” screen appears.

ᮤ

ᮣ

4. Use the and buttons to select “ON”.

ᮤ

ᮣ

ᮤ

ᮣ

5. Adjust the time using the ▲▲ and buttons.

The mode switches as follows each time the or

button is pressed:

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

OFF ↔ ON

• WORKING TIME

LONG LIFE

PLE

AUTO

OFF

→ON ↔ 00H03M ↔ 00H06M ↔ ..... ↔ 12H42M ↔ 12H45M←

ORBITER

INVERSE

SCREEN WIPER

SOFT FOCUS

• WAITING TIME

OFF

→00H03M ↔ 00H06M ↔ 00H09M ↔ ... ↔ 12H42M ↔ 12H45M←

SEL.

ADJ.

EXIT RETURN

INVERSE/WHITE

WORKING TIME

WAITING TIME

01H30M

02H00M

Information

Ⅵ SCREEN WIPER

ON......... The white vertical bar appears.

You can set the time by pressing the MENU/

SEL.

ADJ.

EXIT RETURN

ENTER button while “ON” is set.

OFF ....... Screen wiper mode does not function.

Information

Ⅵ Setting the time

Setting the time for SCREEN WIPER

WORKING TIME ..... Set the time duration for

“INVERSE/WHITE”.

Set a time duration and the speed.

Example: Setting to that the SCREEN WIPER mode

starts in 30 minutes and proceeds for one hour and

a half.

When the WORKING TIME is set

to “ON” the mode will stay on.

WAITING TIME ...... Set the standby time until the

“INVERSE/WHITE” mode starts.

Perform Steps 1-3 of SCREEN WIPER, then...

* The “WAITING TIME” can not be set when the

“WORKING TIME” is ON.

ᮤ

ᮣ

4. Use the and buttons to select “ON”, then press the

MENU/ENTER button.

* THE “WORKING TIME” and “WAITING TIME” can

be set for up to 12 hours and 45 minutes in units of 3

minutes.

THE “SCREEN WIPER” screen appears.

ᮤ

ᮣ

5. Adjust the time and speed using the ▲▲ and buttons.

ᮤ

ᮣ

The mode switches as follows each time the or

* Ending a WORKING TIME function, the monitor will

be STAND BY.

button is pressed:

• WORKING TIME

[Example]

WORKING TIME: 01H30M

WAITING TIME: 02H00M

→ON ↔ 00H03M ↔ 00H06M ↔ ..... ↔ 12H42M ↔ 12H45M←

• WAITING TIME

←−−−− 2 H −−−−→←−− 1.5 H −−→←−−−−

→00H03M ↔ 00H06M ↔ 00H09M ↔ ... ↔ 12H42M ↔ 12H45M←

Start

INVERSE/WHITE Start STAND BY

Ⅵ To select “ON” for the “WORKING TIME”...

• SPEED

Set the hours of the working time to 0H and the minutes

→1 ↔ 2 ↔ 3 ↔ 4 ↔ 5←

to 0M. “ON” will be displayed.

SCREEN WIPER

WORKING TIME

WAITING TIME

SPEED

01H30M

00H30M

SEL.

ADJ.

EXIT RETURN

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the gray level for the sides of the screen

Use this procedure to set the gray level for the parts on the

screen on which nothing is displayed when the screen is

set to the 4:3 size.

Information

Ⅵ Setting the time

WORKING TIME ..... Set the time duration for “SCREEN

WIPER”.

Example: Adjusting the “GRAY LEVEL”

When the WORKING TIME is set

to “ON” the mode will stay on.

WAITING TIME ...... Set the standby time until the

“SCREEN WIPER” mode starts.

SPEED ................ Set the moving speed for the

“SCREEN WIPER”. The speed

decreases as the number increases.

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

1. On the MAIN MENU, select “OPTION2”, then press

the MENU/ENTER button.

The “OPTION2” screen appears.

2. Use the ▲ and ▲ buttons to select “GRAY LEVEL”.

* The “WAITING TIME” can not be set when the

“WORKING TIME” is ON.

3. To adjust the “GRAY LEVEL”...

ᮤ

ᮣ

Use the and buttons to adjust the GRAY LEVEL.

* THE “WORKING TIME” and “WAITING TIME” can

be set for up to 12 hours and 45 minutes in units of 3

minutes.

OPTION2

POWER MGT.

2 / 3

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

SOFT FOCUS

OFF

Reduces edges and softens the image.

Example: Setting “SOFT FOCUS” to “2”

SEL.

ADJ.

EXIT RETURN

Information

Ⅵ GRAY LEVEL settings

Perform Steps 1-2 of LONG LIFE, then...

3. Use the ▲ and ▲ buttons to select “SOFT FOCUS”.

This adjusts the brightness of the black (the gray level)

for the sides of the screen.

The standard is 0 (black). The level can be adjusted

from 0 to 15. The factory setting is 3 (dark gray).

ᮤ

ᮣ

4. Use the and buttons to select “2”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

→OFF ↔ 1 ↔ 2 ↔ 3 ↔ 4

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

LONG LIFE

PLE

AUTO

OFF

ORBITER

INVERSE

SCREEN WIPER

SOFT FOCUS

Setting the screen size for S1/S2 video input

If the S-video signal contains screen size information, the

image will be automatically adjusted to fit the screen when

this S1/S2 is set to AUTO.

This feature is available only when an S-video signal is

input via the VIDEO3 terminal.

SEL.

ADJ.

EXIT RETURN

Information

Ⅵ SOFT FOCUS settings

OFF ............Turns the SOFT FOCUS function off.

Example: Setting the “S1/S2” to “AUTO”

1, 2, 3, 4 .....Activates the SOFT FOCUS setting. The

higher numbers create a softer image.

“SHARPNESS” can not be adjusted on

the “PICTURE” menu.

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

1. On the MAIN MENU, select “OPTION2”, then press

the MENU/ENTER button.

The “OPTION2” screen appears.

2. Use the ▲ and ▲ buttons to select “S1/S2”.

ᮤ

ᮣ

3. Use the and buttons to select “AUTO”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

OFF ↔ AUTO

OPTION2

POWER MGT.

2 / 3

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

AUTO

SEL.

ADJ.

EXIT RETURN

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the signal and black level for DVI

signal

Information

Ⅵ S1/S2 settings

Choose the signal for the DVI connector (PC or STB/

DVD) and set the black level.

AUTO .....Adjusts the screen size automatically

according to the S1/S2 video signal.

Example: Setting the “PLUG/PLAY” mode to “STB/

OFF ....... Turns the S1/S2 function off.

DVD”

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

1. On the MAIN MENU, select “OPTION2”, then press

the MENU/ENTER button.

The “OPTION2” screen appears.

Setting the picture size for RGB input signals

Use this procedure to switch the setting to “ON” or “OFF”.

2. Use the ▲ and ▲ buttons to select “DVI SET UP”,

then press the MENU/ENTER button.

Example: Setting the “PICTURE SIZE” mode to

“OFF”

The “DVI SET UP” screen appears.

3. To set PLUG/PLAY mode to “STB/DVD”...

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

ᮤ

ᮣ

Use the and buttons to select “STB/DVD”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

PLUG/PLAY:

1. On the MAIN MENU, select “OPTION2”, then press

the MENU/ENTER button.

PC ↔ STB/DVD

The “OPTION2” screen appears.

BLACK LEVEL: LOW ↔ HIGH

DVI SET UP

2. Use the ▲ and ▲ buttons to select “PICTURE SIZE”.

PLUG/PLAY

STB/DVD

HIGH

BLACK LEVEL

3. To set PICTURE SIZE mode to “OFF”...

ᮤ

ᮣ

Use the and buttons to select “OFF”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

SEL.

ADJ.

EXIT RETURN

ON ↔ OFF

OPTION2

POWER MGT.

2 / 3

Information

Ⅵ PLUG/PLAY settings

PC ..............When connected to the PC signal.

OFF

CINEMA MODE

LONG LIFE

GRAY LEVEL

S1/S2

OFF

BLACK LEVEL is set to “LOW”

automatically.

PICTURE SIZE

DVI SET UP

SEL.

ADJ.

EXIT RETURN

STB/DVD ...When connected to the SET TOP BOX,

DVD etc.

Information

Ⅵ Restoring the factory default settings

BLACK LEVEL is set to “HIGH”

automatically.

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

Ⅵ BLACK LEVEL settings

LOW ...........When connected to the PC signal.

HIGH ..........When connected to the SET TOP BOX,

DVD etc. Change “HIGH” into “OFF”

if the black level appears gray.

Download from Www.Somanuals.com. All Manuals Search And Download.

• DAYLIGHT SAVING TIME

Option3 Settings Menu

Using the timer

This function sets the monitor to turn ON/OFF

ON ↔ OFF

• Day

→SUNDAY ↔ MONDAY ↔ ..... ↔ FRIDAY ↔ SATURDAY←

automatically at a set time.

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

• Hour/Minutes

→ 00:00 ↔ 00:01 ↔ 00:02 ↔ ..... ↔ 23:58 ↔ 23:59←

1. On the MAIN MENU, select “OPTION3”, then press

the MENU/ENTER button.

5. Once the setting is completed...

Use the ▲ and ▲ buttons to select “SET”, then press

the MENU/ENTER button.

The “OPTION3” screen appears.

2. Use the ▲ and ▲ buttons to select “TIMER”, then press

the MENU/ENTER button.

The adjustments are stored and return to the TIMER

menu.

The “TIMER” screen appears.

PRESENT TIME

RETURN

TIMER

PRESENT TIME

DAYLIGHT

PROGRAM

OFF

SAVING TIME

OFF

WEDNESDAY

22 : 05 : 00

SET

SEL.

MENU/ENTER

EXIT RETURN

SEL.

MENU/ENTER

EXIT RETURN

Information

ᮤ

ᮣ

3. Set the TIMER using ▲▲ and buttons.

See page 32 to set PRESENT TIME.

See page 33 to set PROGRAM.

Ⅵ PRESENT TIME settings

DAYLIGHT SAVING TIME

Information

........................ Use to set DAYLIGHT SAVING

TIME.

Ⅵ Restoring the factory default settings

ON: The present time + 1 hour.

OFF: Cancelled

Day................Set the day of the week (e.g. Sunday).

Hour ..............Set the hour in the 24-hour format

(range 00 to 23).

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

PRESENT TIME

Minutes .........Set the minutes (range 00 to 59).

This sets the day of the week and present time.

Example: Setting “WEDNESDAY”, “22:05”

* If you press the EXIT button instead of the MENU/

ENTER button in step 5, the settings can not be mode.

Perform Steps 1-2 of TIMER, then...

3. Use the ▲ and ▲ buttons to select “PRESENT TIME”,

then press the MENU/ENTER button.

The “PRESENT TIME” screen appears.

PRESENT TIME

RETURN

DAYLIGHT

SAVING TIME

OFF

WEDNESDAY

13 : 00 : 00

SEL.

EXIT RETURN

ADJ.

4. Use the ▲ and ▲ buttons to select the item, then adjust

ᮤ

ᮣ

using the

and buttons.

PRESENT TIME

RETURN

DAYLIGHT

SAVING TIME

OFF

WEDNESDAY

22 : 05 : 00

SEL.

EXIT RETURN

ADJ.

ᮤ

The mode switches as follows each time the or

button is pressed:

ᮣ

Download from Www.Somanuals.com. All Manuals Search And Download.

FUNCTION ............. Set the LONG LIFE function.

PROGRAM TIMER

This sets the day and time at which the power will be

switched ON/OFF as well as the input mode.

Ⅵ To reset the program

Align the cursor with the DATE field that you wish to

reset, then press the CLEAR button.

Example: Setting so that the power will be switched

on at 8:30 A.M., Monday, displaying RGB2 source,

and switched off at 10:30 A.M.

Ⅵ To reset the data

Align the cursor with the field (ON/OFF/INPUT/

FUNCTION) that you wish to reset, then press the

CLEAR button.

Perform Steps 1-2 of TIMER, then...

3. Use the ▲ and ▲ buttons to select “PROGRAM”.

TIMER

Ⅵ Special characters in the PROGRAM TIMER

PRESENT TIME

screen

PROGRAM

OFF

PROGRAM TIMER

FUNCTION

INVERSE

—

DATE

OFF INPUT

MON 08 : 30 10 : 30

RGB2

—

TUE

SAT

- - : - - 18 : 15

WHITE

—

08 : 30 12 : 15 VIDEO1

*FRI 08 : 30 10 : 00 HD/DVD1

SEL.

ADJ.

EXIT RETURN

—

SAT

- - : - -

—

WHITE

—

EXIT RETURN

08 : 30 12 : 15 VIDEO1

ᮤ

ᮣ

4. Use the and buttons to select “ON”, then press the

MENU/ENTER button.

15 : 30 16 : 00

SEL. ZOOM ADJ.

RGB1

• An asterisk “*” in the DATE field

The “PROGRAM TIMER” screen appears.

An asterisk “*” means “every”. For example, “*FRI”

means every Friday and “*” means everyday.

ᮤ

ᮣ

5. Adjust using the ▲▲ and buttons and ZOOM

button.

• A hyphen “-” in the ON field or OFF field

If any hyphen remains in the ON field or OFF field, the

FUNCTION can not be set.

PROGRAM TIMER

FUNCTION

DATE

OFF INPUT

INVERSE

MON 08 : 30 10 : 30

RGB2

—

- - : - -

—

• A hyphen “-” in the FUNCTION field

A hyphen “-” means last mode (the mode that was last

selected at the time the power was switched off).

—

SEL. ZOOM ADJ.

EXIT RETURN

Setting the power on mode

This function sets the input mode at the time the power is

switched on.

The mode switches as follows each time the ZOOM

button is pressed:

• Date

Example: Setting “VIDEO2”

→ — ↔ SUN ↔ MON ↔ ... ↔ SAT ↔ * ↔ *SUN ↔ *MON ↔ ... ↔ *SAT←

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

• ON/OFF Hour

→ 00 ↔ 01 ↔ 02 ↔ ..... ↔ 21 ↔ 22 ↔ 23←

1. On the MAIN MENU, select “OPTION3”, then press

the MENU/ENTER button.

• Minute

The “OPTION3” screen appears.

→ 00 ↔ 01 ↔ 02 ↔ ..... ↔ 57 ↔ 58 ↔ 59←

2. Use the ▲ and ▲ buttons to select “PWR. ON MODE”.

• INPUT

3. To set the PWR. ON MODE to “VIDEO2”...

→ — ↔ LAST ↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ↔ HD/DVD1 ←

→ RGB3 ↔ RGB2 ↔ RGB1 ↔ HD/DVD2 ←

ᮤ

ᮣ

Use the and buttons to select “VIDEO2”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

• FUNCTION

The available inputs depend on the setting of “BNC

INPUT”.

→ — ↔ ORBITER ↔ INVERSE ↔ WHITE ↔ WIPER←

RGB:

→ LAST ↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ←

→ RGB3 ↔ RGB2 ↔ RGB1 ↔ HD/DVD1 ←

Information

→ LAST ↔ VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ←

COMP:

Ⅵ PROGRAM TIMER settings

→ RGB3 ↔ RGB1 ↔ HD/DVD2 ↔ HD/DVD1 ←

DATE....................... Set the day of the week (e.g.

Sunday).

ON (hour, minutes) .... Set the time at which the power

will be turned on in the 24-hour

format.

OFF (hour, minutes)... Set the time at which the power

will be turned off in the 24-hour

format.

OPTION3

TIMER

3 / 3

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

VIDEO2

OFF

ID NUMBER

VIDEO WALL

SEL.

ALL

ADJ.

EXIT RETURN

INPUT ..................... Set the input mode that will be

displayed when the timer is on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Enabling/disabling remote control wireless

transmission

Information

Ⅵ PWR. ON MODE settings

This function enables/disables remote control wireless

transmission.

LAST ................Last mode (the mode that was last

selected at the time the power was

switched off).

VIDEO1, 2, 3.... VIDEO input mode.

RGB1, 2, 3 ....... RGB input mode.

HD/DVD1, 2 ..... HD/DVD input mode.

Example: Setting “OFF”

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

1. On the MAIN MENU, select “OPTION3”, then press

the MENU/ENTER button.

Ⅵ Restoring the factory default settings

The “OPTION3” screen appears.

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

2. Use the ▲ and ▲ buttons to select “IR REMOTE”.

3. To set the IR REMOTE to “OFF”...

ᮤ

ᮣ

Use the and buttons to select “OFF”, then press

the MENU/ENTER button.

The mode switches as follows each time the or

Enabling/disabling the front panel controls

This function enables/disables the front panel controls.

ᮤ

ᮣ

button is pressed:

Example: Setting “ON”

OFF

↔

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

OPTION3

TIMER

3 / 3

1. On the MAIN MENU, select “OPTION3”, then press

the MENU/ENTER button.

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

LAST

OFF

ALL

The “OPTION3” screen appears.

ID NUMBER

VIDEO WALL

SEL.

2. Use the ▲ and ▲ buttons to select “CONTROL

ADJ.

EXIT RETURN

LOCK”.

Information

Ⅵ IR REMOTE settings

3. To set the CONTROL LOCK to “ON”...

ᮤ

ᮣ

Use the and buttons to select “ON”, then press the

MENU/ENTER button.

The mode switches as follows each time the or

button is pressed:

ON...... Enables remote control wireless transmission.

OFF .... Disables remote control wireless transmission.

Set “OFF” to avoid unwanted control from

other remote controls.

ᮤ

ᮣ

OFF

↔

OPTION3

TIMER

3 / 3

Ⅵ Restoring the factory default settings

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

LAST

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

OFF

ALL

ID NUMBER

VIDEO WALL

SEL.

ADJ.

EXIT RETURN

Information

Ⅵ CONTROL LOCK settings

ON...... Disables the buttons on the front panel.

OFF .... Enables the buttons on the front panel.

* Even when the CONTROL LOCK is set, the POWER

switch will not be locked.

* This becomes effective when the on-screen menu goes

out.

Ⅵ Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loop Out setting

button is pressed:

When this feature is set to ON, the received signal will be

→ALL ↔ 1 ↔ 2 ↔ ..... ↔ 255 ↔ 256←

looped out.

Example: Setting “ON”

OPTION3

TIMER

3 / 3

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

LAST

OFF

1. On the MAIN MENU, select “OPTION3”, then press

the MENU/ENTER button.

OFF

ID NUMBER

VIDEO WALL

SEL.

The “OPTION3” screen appears.

ADJ.

EXIT RETURN

* To reset back to ALL

Press the CLEAR button.

2. Use the ▲ and ▲ buttons to select “LOOP OUT”.

3. To set the LOOP OUT to “ON”...

ᮤ

ᮣ

Information

Use the and buttons to select “ON”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

Ⅵ ID NUMBER settings

ALL...........ID NUMBER will not be set.

1 to 256 ....ID NUMBER will be set.

OFF

↔

OPTION3

TIMER

3 / 3

Ⅵ When the ID NUMBER have been set

PWR. ON MODE

CONTROL LOCK

IR REMOTE

LOOP OUT

LAST

OFF

You can also set ID NUMBER for each remote control

to operate the plasma display individually. To do so,

see below.

ID NUMBER

VIDEO WALL

SEL.

ALL

Ⅵ Restoring the factory default settings

ADJ.

EXIT RETURN

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

Information

Ⅵ LOOP OUT settings

ON...... The received signal will be looped out via PC1

terminal or VIDEO1 terminal.

To set the ID number for the remote control

OFF .... The received signal will not loop out.

Example: Setting “2”

* Even if LOOP OUT is ON, signals won’t be sent out if

POWER is being turned off.

1. Press the ID SELECT button on the remote control.

The “ID SELECT” screen appears.

Ⅵ To connect another display...

2. Use the ▲ and ▲ buttons to select “ID NUMBER”.

See page 10.

3. To set the ID NUMBER to “2”...

ᮤ

ᮣ

Ⅵ If the RGB/PC1 signal is present at the time

Use the and buttons to select “2”.

ᮤ

ᮣ

the power switched on...

The mode switches as follows each time the or

button is pressed:

The RGB/PC1 input will be displayed regardless of the

setting of LOOP OUT.

→ALL ↔ 1 ↔ 2 ↔ ..... ↔ 255 ↔ 256←

Ⅵ Restoring the factory default settings

ID SELECT

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

POSITION :

ID NUMBER

ID number setting

ADJ.

EXIT

RETURN

When using more than one of these displays, this function

sets ID numbers so that operation of the remote control

does not cause multiple monitors to operate at the same

time.

* To reset back to ALL

Press the CLEAR button.

4. Once the setting is completed...

Press the EXIT button to delete the ID SELECT screen.

Example: Setting “2”

Set “ADVANCED OSM” to “ON” in the main menu (1/

2), then perform the following operations.

1. On the MAIN MENU, select “OPTION3”, then press

the MENU/ENTER button.

The “OPTION3” screen appears.

2. Use the ▲ and ▲ buttons to select “ID NUMBER”.

3. To set the ID NUMBER to “2”...

ᮤ

ᮣ

Use the and buttons to select “2”.

The mode switches as follows each time the or

ᮤ

ᮣ

Download from Www.Somanuals.com. All Manuals Search And Download.

Video Wall setting

Use this feature to configure a 2×2 or 3×3 video wall.

Set “ADVANCED OSM” to “ON” in the main menu (1/

Information

Ⅵ DIVIDER settings

OFF, 1 .......1 Screen (Matrix display function does not

work)

4 ................4 Screens (2×2 video wall)

9 ................9 Screens (3×3 video wall)

2), then perform the following operations.

1. On the MAIN MENU, select “OPTION3”, then press

the MENU/ENTER button.

The “OPTION3” screen appears.

* When you select “4” or “9”, set the VIDEO WALL

2. Use the ▲ and ▲ buttons to select “VIDEO WALL”,

then press the MENU/ENTER button.

POSITION.

The “VIDEO WALL” screen appears.

VIDEO WALL POSITION

Set the position of each display.

Example: Setting “4”

VIDEO WALL

DIVIDER

POSITION

DISP. MODE

AUTO ID

SPLIT

OFF

Perform Steps 1-2 of VIDEO WALL, then...

IMAGE ADJUST

P. ON DELAY

PLE LINK

OFF

3. Use the ▲ and ▲ buttons to select “POSITION”, then

press the MENU/ENTER button.

REPEAT TIMER

SEL.

OFF

EXIT RETURN

ADJ.

The “VIDEO WALL POSITION” screen appears.

ᮤ

ᮣ

3. Set the VIDEO WALL using ▲▲ and buttons.

See page 36 to set DIVIDER.

ᮤ

ᮣ

4. Use the and buttons to select “NO. 4”.

ᮤ

ᮣ

The mode switches as follows each time the or

See page 36 to set POSITION.

See page 37 to set DISP. MODE.

See page 37 to set AUTO ID.

button is pressed:

• 4 Screens

→ NO. 1 ↔ NO. 2 ↔ NO. 3 ↔ NO. 4 ←

See page 37 to set IMAGE ADJUST.

See page 38 to set P. ON DELAY.

See page 38 to set PLE LINK.

• 9 Screens

See page 39 to set REPEAT TIMER.

→ NO. 7 ↔ NO. 8 ↔ ....... ↔ NO. 14 ↔ NO. 15 ←

4. Once the setting is completed...

Press the EXIT button to return to the OPTION3 menu.

VIDEO WALL POSITION

POSITION NO.

Note: A contingency method of shutting off the electric

power should be used in cases of emergency during video

wall setup.

ADJ.

EXIT

RETURN

Information

Ⅵ Restoring the factory default settings

Ⅵ VIDEO WALL POSITION settings

1 Screen.....There is no need to set POSITION.

4 Screens

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

NO. 1

NO. 2

DIVIDER

NO. 4

NO. 3

Set the 2×2 or 3×3 video wall.

Example: Setting “4”

9 Screens

Perform Steps 1-2 of VIDEO WALL, then...

NO. 8

NO. 11

NO. 14

NO. 9

NO. 7

3. Use the ▲ and ▲ buttons to select “DIVIDER”.

NO. 12

NO. 15

NO. 10

NO. 13

ᮤ

ᮣ

4. Use the and buttons to select “4”.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

→ OFF ↔ 1 ↔ 4 ↔ 9 ←

VIDEO WALL

DIVIDER

POSITION

DISP. MODE

AUTO ID

SPLIT

OFF

IMAGE ADJUST

P. ON DELAY

PLE LINK

OFF

REPEAT TIMER

SEL.

OFF

EXIT RETURN

ADJ.

Download from Www.Somanuals.com. All Manuals Search And Download.

DISP. MODE

Information

Select the screen mode from between two options

(Splitting, Blanking).

Ⅵ AUTO ID settings

ON...... Enables Auto ID function. In the case shown

below, display 1 will be set as ID 1, display 2

as ID2, etc.

Example: Setting “BLANK”

Perform Steps 1-2 of VIDEO WALL, then...

REMOTE

OUT

3. Use the ▲ and ▲ buttons to select “DISP. MODE”.

No.1

No.2

REMOTE

OUT

REMOTE

No.4 No.3

REMOTE

ᮤ

ᮣ

4. Use the and buttons to select “BLANK”.

Display 2

Display 1

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

SPLIT ↔ BLANK

VIDEO WALL

REMOTE

OUT

No.1

No.2

REMOTE

OUT

REMOTE

No.4 No.3

REMOTE

DIVIDER

Display 3

Display 4

POSITION

DISP. MODE

AUTO ID

BLANK

OFF

OFF .... Disables Auto ID function.

IMAGE ADJUST

P. ON DELAY

PLE LINK

OFF

IMAGE ADJUST

REPEAT TIMER

SEL.

OFF

EXIT RETURN

ADJ.

The position of the image can be adjusted and flickering

of the image can be corrected.

Information

Ⅵ DISP. MODE settings

Example: Adjusting the vertical position

Perform Steps 1-2 of VIDEO WALL, then...

SPLIT .........Combines enlarged screens and creates

multiple screens.

BLANK .......Corrects misalignment of combined screen

portions and creates multiple screens

3. Use the ▲ and ▲ buttons to select “IMAGEADJUST”,

then press the MENU/ENTER button.

The “IMAGE ADJUST” screen appears.

4. Use the ▲ and ▲ buttons to select “V-POSITION”.

AUTO ID

IMAGE ADJUST

This feature automatically sets the ID numbers of multiple

displays connected to each other.

ASPECT MODE

V-POSITION

H-POSITION

V-HEIGHT

NORMAL

Example: Setting “ON”

H-WIDTH

Set the ID number for the No. 1 display on ID NUMBER

menu.

AUTO PICTURE

FINE PICTURE

PICTURE ADJ.

SEL.

OFF

ADJ.

EXIT RETURN

Perform Steps 1-2 of VIDEO WALL, then...

ᮤ

ᮣ

5. Adust using the and buttons.

3. Use the ▲ and ▲ buttons to select “AUTO ID”.

ᮤ

ᮣ

4. Use the and buttons to select “ON”, then press the

MENU/ENTER button.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

OFF ↔ ON

AUTO ID

V-POSITION

AUTO ID

ᮤ

ᮣ

* If neither the or button is pressed within 5 seconds,

the current setting is set and the previous screen

reappears.

WIRED CABLE

CONNECTION TURN

Information

ADJ.

EXIT

RETURN

Ⅵ IMAGE ADJUST settings

These are the same functions as the IMAGE ADJUST

menu on page 22.

Download from Www.Somanuals.com. All Manuals Search And Download.

P. ON DELAY (Power on delay)

PLE LINK

Use this function to activate power-on delay.

Turn on the AUTO ID before the following operations.

Use this function to set a uniform brightness for each

display.

Turn on the AUTO ID and set the DIVIDER (at 1, 4 or 9)

before the following operations.

Example: Setting “ON”

Perform Steps 1-2 of VIDEO WALL, then...

Example: Setting “ON”

3. Use the ▲ and ▲ buttons to select “P. ON DELAY”.

Perform Steps 1-2 of VIDEO WALL, then...

ᮤ

ᮣ

4. Use the and buttons to select “ON”.

3. Use the ▲ and ▲ buttons to select “PLE LINK”.

ᮤ

ᮣ

The mode switches as follows each time the or

ᮤ

ᮣ

button is pressed:

4. Use the and buttons to select “ON”, then press the

MENU/ENTER button.

OFF ↔ ON

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

VIDEO WALL

DIVIDER

POSITION

DISP. MODE

AUTO ID

SPLIT

OFF

OFF ↔ ON

VIDEO WALL

IMAGE ADJUST

P. ON DELAY

PLE LINK

DIVIDER

POSITION

DISP. MODE

AUTO ID

OFF

SPLIT

OFF

REPEAT TIMER

SEL.

OFF

EXIT RETURN

ADJ.

IMAGE ADJUST

P. ON DELAY

PLE LINK

OFF

Information

Ⅵ P. ON DELAY settings

REPEAT TIMER

SEL.

OFF

EXIT RETURN

ADJ.

ON...... Turns on the main power of each display after

a delay time.

OFF .... Turns on the main power of all displays at the

same time.

Information

Ⅵ PLE LINK settings

ON...... Sets a uniform brightness for each screen in a

video wall.

OFF .... Sets the individual screen brightness for each

screen in a video wall.

* Once this function has been set to “ON”, POWER ON/

OFF button on the remote control does not function

except for the No.1 monitor.

By pressing the POWER ON button on the remote

control the No.1 monitor will turn on and the others

will be turned on one by one automatically.

* When this function is set “ON”, connect your plasma

displays with the remote cable (optional) in the order of

the position numbers for the 2×2 video wall. See the

drawing below.

* From the second monitor onward, neither the POWER

button on the unit nor the POWER ON button on the

remote control does function. However, by pressing and

holding the POWER ON button for more than 3 seconds,

the monitor will be turned on.

* If there are changes in the DIVIDER or POSITION,

the PLE LINK will automatically turn OFF.

REMOTE

OUT

No.1

No.2

REMOTE

OUT

REMOTE

No.4 No.3

REMOTE

Display 2

Display 1

REMOTE

OUT

No.1

No.2

REMOTE

OUT

REMOTE

No.4 No.3

REMOTE

Display 3

Display 4

* With the 3×3 video wall, connect the final display to

the first display the same way as with 2×2 video wall.

Note: The remote control can be operated unless the

IR REMOTE is set to “OFF”.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPEAT TIMER

Advanced OSM Settings Menu

Setting the menu mode

This allows you to access full menu items.

When P. ON DELAY or PLE LINK is ON, this won’t be

turned OFF.

Use this to set two timers. Each timer can use the

DIVIDER, SOURCE and WORK TIME functions.

Turn on the AUTO ID and set the DIVIDER (at 1, 4 or 9)

before the following operations.

Example: Setting “ON”

Example:

TIMER1...VIDEO1 will be displayed for 3 minutes.

TIMER2...RGB1 will be displayed for 6 minutes in a

2×2 video wall.

1. On the MAIN MENU, select “ADVANCED OSM”.

MAIN MENU

1 / 2

PICTURE

AUDIO

Perform Steps 1-2 of VIDEO WALL, then...

3. Use the ▲ and ▲ buttons to select “REPEAT TIMER”.

VIDEO WALL

IMAGE ADJUST

OPTION1

ADVANCED OSM

SEL.

OFF

DIVIDER

EXIT EXIT

ADJ.

POSITION

DISP. MODE

AUTO ID

SPLIT

OFF

2. To set the ADVANCED OSM to “ON”...

IMAGE ADJUST

P. ON DELAY

PLE LINK

ᮤ

ᮣ

Use the and buttons to select “ON”.

OFF

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

OFF

REPEAT TIMER

SEL.

OFF

EXIT RETURN

ADJ.

OFF ↔ ON

MAIN MENU

1 / 2

ᮤ

ᮣ

4. Use the and buttons to select “ON”, then press the

MENU/ENTER button.

PICTURE

AUDIO

IMAGE ADJUST

OPTION1

The “REPEAT TIMER” screen appears.

OPTION2

ᮤ

ᮣ

5. Adust using the ▲▲ and buttons.

OPTION3

ADVANCED OSM

SEL.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

EXIT EXIT

ADJ.

REPEAT TIMER

Information

Ⅵ ADVANCED OSM settings

DIVIDER

SOURCE

VIDEO1

00H03M

WORK TIME

ON...... All of the main menu items are available for

advanced users.

DIVIDER

SOURCE

RGB1

00H06M

WORK TIME

OFF .... Some of the main menu items are not available

(e.g. OPTION2, OPTION3).

SEL.

ADJ.

EXIT RETURN

• DIVIDER

Ⅵ Restoring the factory default settings

→ 1 ↔ 4 ↔ 9

←

Select “ALL RESET” under the OPTION1 menu. Note

that this also restores other settings to the factory

defaults.

• SOURCE

The available sources depend on the setting of “BNC

INPUT”.

→

VIDEO1 ↔ VIDEO2 ↔ VIDEO3 ↔ HD/DVD1 ←

→ RGB3 RGB2 RGB1 HD/DVD2

↔

←

• WORK TIME

→ 00H01M ↔ 00H02M ↔ 00H03M ↔ ..... ↔ 04H14M ↔ 04H15M ←

Information

Ⅵ REPEAT TIMER settings

If you set both timers, Timer 1 and Timer 2 run

consecutively.

In the case of the Video wall, timer No.1 can be used to

control all the displays simultaneously.

* This becomes effective when the on-screen menu goes

out.

Download from Www.Somanuals.com. All Manuals Search And Download.

Language Settings Menu

Setting the language for the menus

The menu display can be set to one of seven languages:

English, German, French, Swedish, Italian, Spanish or

Chinese.

Information

Ⅵ Video signal formats

Different countries use different formats for video

signals. Set to the color system used in your current

country.

AUTO ..............The color systems are automatically

identified and the format is set

accordingly.

Example: Setting the menu display to “DEUTSCH”

1. On the MAIN MENU, select “LANGUAGE”, then

press the MENU/ENTER button.

The “LANGUAGE” screen appears.

PAL..................This is the standard format used

mainly in the United Kingdom and

Germany.

SECAM............. This is the standard format used

mainly in France and Russia.

2. To select “DEUTSCH” ...

ᮤ

ᮣ

Use the and buttons to select “ DEUTSCH”.

ᮤ

ᮣ

The mode switches as follows each time the or

buttons is pressed:

4.43 NTSC,

→ ENGLISH ↔ DEUTSCH ↔ FRANÇAIS ←

PAL60 .............This format is used for videos in

countries using PAL and SECAM

video signals.

→

↔ SVENSKA ↔ ITALIANO ↔ ESPAÑOL ←

LANGUAGE

3.58 NTSC ......This is the standard format used

mainly in the United States and Japan.

PAL-M .............This is the standard format used

mainly in Brazil.

LANGUAGE

DEUTSCH

PAL-N..............This is the standard format used

mainly in Argentina.

MENU/ENTER

EXIT

RETURN

ADJ.

Information

Ⅵ Language settings

Source Information Menu

Checking the frequencies, polarities of input

signals, and resolution

ENGLISH ........English

DEUTSCH....... German

FRANÇAIS ...... French

ESPAÑOL .......Spanish

ITALIANO ........ Italian

SVENSKA ....... Swedish

................... Chinese

Use this function to check the frequencies and polarities

of the signals currently being input from a computer, etc.

Press the MENU/ENTER button on the remote control to

display the MAIN MENU on the screen, then...

1. On the MAIN MENU, select “SOURCE

INFORMATION”, then press the MENU/ENTER

button.

Color System Settings Menu

Setting the video signal format

2. The “SOURCE INFORMATION” is displayed.

Use these operations to set the color systems of composite

SOURCE INFORMATION

video signals or Y/C input signals.

H. FREQ

V. FREQ

48.4KHZ

60.0KHZ

Example: Setting the color system to “3.58 NTSC”

H. POLARITY

V. POLARITY

NEG.

1. On the MAIN MENU, select “COLOR SYSTEM”, then

press the MENU/ENTER button.

MEMORY

RESOLUTION

1024×768

The “COLOR SYSTEM” screen appears.

EXIT

RETURN

2. To select “ 3.58NTSC ” ...

PC:

MEMORY will be displayed.

ᮤ

ᮣ

Use the and buttons to select “ 3.58NTSC ”.

Others: MODE will be displayed.

ᮤ

ᮣ

The mode switches as follows each time the or

button is pressed:

→ AUTO ↔ 3.58NTSC ↔ 4.43NTSC ←

→ SECAM ↔ PAL-M ↔ PAL-N ↔ PAL60 ↔ PAL ←

COLOR SYSTEM

3.58NTSC

EXIT

RETURN

ADJ.

Download from Www.Somanuals.com. All Manuals Search And Download.

External Control

Application

These specifications cover the communications control of

the plasma monitor by external equipment.

External Control Codes (Reference)

FUNCTION

Power ON

OFF

CODE DATA

9FH 80H 60H 4EH 00H CDH

9FH 80H 60H 4FH 00H CEH

Input Switch Video1 (BNC)

Video2 (RCA)

DFH 80H 60H 47H 01H 01H 08H

DFH 80H 60H 47H 01H 02H 09H

DFH 80H 60H 47H 01H 03H 0AH

DFH 80H 60H 47H 01H 05H 0CH

DFH 80H 60H 47H 01H 06H 0DH

Connections

Connections are made as described below.

Video3 (S-Video)

DVD1/HD1 (RCA)

DVD2/HD2 (BNC)

RGB1 (mini D-sub 15-pin) DFH 80H 60H 47H 01H 07H 0EH

RGB2 (5BNC)

RGB3 (DVI)

DFH 80H 60H 47H 01H 08H 0FH

DFH 80H 60H 47H 01H 0CH 13H

External equipment

e.g., Personal computer

Audio Mute ON

9FH 80H 60H 3EH 00H BDH

9FH 80H 60H 3FH 00H BEH

OFF

Picture Mode NORMAL

THEAT. 1

DFH 80H 60H OAH 01H 01H CBH

DFH 80H 60H OAH 01H 02H CCH

DFH 80H 60H OAH 01H 03H CDH

DFH 80H 60H OAH 01H 04H CEH

THEAT. 2

DEFAULT

Screen Mode STADIUM

DFH 80H 60H 51H 01H 02H 13H

DFH 80H 60H 51H 01H 03H 14H

DFH 80H 60H 51H 01H 04H 15H

DFH 80H 60H 51H 01H 05H 16H

DFH 80H 60H 51H 01H 09H 1AH

DFH 80H 60H 51H 01H 0AH 1BH

ZOOM

NORMAL

FULL

14 : 9

2.35 : 1

Auto Picture ON

OFF

DFH 80H 60H 7FH 03H 03H 09H 00H 4DH

DFH 80H 60H 7FH 03H 03H 09H 01H 4EH

Display

Connector on the plasma monitor side: EXTERNAL

CONTROL connector.

Cinema Mode ON

OFF

DFH 80H 60H C1H 01H 01H 82H

DFH 80H 60H C1H 01H 02H 83H

Use a crossed (reverse) cable.

Note: Contact your local dealer for a full list of the

External Control Codes if needed.

Type of connector: D-Sub 9-pin male

Pin No.

Pin Name

No Connection

RXD (Receive data)

TXD (Transmit data)

DTR (DTE side ready)

GND

DSR (DCE side ready)

RTS (Ready to send)

CTS (Clear to send)

No connection

Communication Parameters

(1) Communication system

(2) Interface

(3) Baud rate

(4) Data length

(5) Parity

Asynchronous

RS-232C

9600 bps

8 bits

Odd

(6) Stop bit

1 bit

(7) Communication code

Hex

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service.

Symptom

Checks

Remedy

Mechanical sound is heard.

• Maybe the sound from the cooling fans used to prevent over heating.

• Are the image and sound normal? • If there are no abnormalities in the image

The unit emits a crackling sound.

and sound, the noise is caused by the

cabinet reacting to changes in humidity. This

will not affect performance.

Picture is disturbed.

Sound is noisy.

• Is a connected component set directly in • Leave some space between the display and

front or at the side of the display?

the connected components.

Remote control operates erroneously.

The remote control does not work.

• Are the remote control’s batteries worn

out?

• Replace both batteries with new ones.

• Set IR REMOTE OFF on OPTION3 menu.

• Is IR REMOTE set to ON?

• Has an ID number been set for the main • Set an ID number with the ID SELECT

unit? button, or set the ID number to ALL.

• Is the monitor’s power cord plugged into • Plug the monitor’s power cord into a power

Monitor’s power does not turn on

when the remote control’s power

button is pressed.

a power outlet?

outlet.

• Are all the monitor’s indicators off?

• Press the power button on the monitor to

turn on the power.

• Are the remote control’s batteries worn

out?

• Replace both batteries with new ones.

• Is IR REMOTE set to ON?

• Set IR REMOTE OFF.

• Has an ID number been set for the main • Set an ID number with the ID SELECT

unit?

button, or set the ID number to ALL.

Monitor does not operate when the

remote control’s buttons are pressed. monitor, or is there an obstacle between

the remote control and the monitor?

• Is the remote control pointed at the

• Point the remote control at the monitor’s

remote control sensor when pressing

buttons, or remove the obstacle.

• Is direct sunlight or strong artificial light

shining on the monitor’s remote control

sensor?

• Eliminate the light by closing curtains,

pointing the light in a different direction, etc.

•

Are the remote control’s batteries worn out?

• Replace both batteries with new ones.

• The remote cable is plugged into the

REMOTE IN terminal (Wired).

• Unplug the remote cable from the monitor.

• The front panel buttons do not function

during Control Lock.

• Set the Control Lock to OFF.

The front panel buttons of the main

unit do not function.

No sound or picture is produced.

• Is the monitor’s power cord plugged into • Plug the monitor’s power cord into a power

a power outlet?

outlet.

Picture appears but no sound is

produced.

• Is the volume set at the minimum?

• Is the mute mode set?

• Increase the volume.

•

Press the remote control’s MUTE button.

• Are the speakers properly connected?

• Is AUDIO INPUT set correctly?

• Connect the speakers properly.

• Set AUDIO INPUT on the AUDIO menu

correctly.

Poor picture with VIDEO signal input. •Improper control setting.

Local interference.

• Adjust picture control as needed.

Try another location for the monitor.

Be sure all connections are secure.

Cable interconnections.

Input impedance is not correct level.

Poor picture with RGB signal input.

• Improper control setting.

• Adjust picture controls as needed.

Incorrect 15 PIN connector pin

connections.

Check pin assignments and connections.

Tint is poor or colors are weak.

Nothing appears on screen.

• Are the tint and colors properly adjusted? • Adjust the tint and color (under PICTURE).

• Is the computer’s power turned on?

• Is a source connected?

• Turn on the computer’s power.

• Connect source to the monitor.

• Is the power management function in the • Operate the computer (move the mouse,

standby or off mode?

etc.).

• Is LOOP OUT set to ON?

• Set LOOP OUT OFF.

• Adjust the IMAGE ADJUST properly.

Part of picture is cut off or picture is

not centered.

• Is the position adjustment appropriate?

Image is too large or too small.

• Is the screen size adjustment

appropriate?

• Press the WIDE button on the remote

control and adjust properly.

• Set to the proper resolution.

Picture is unstable.

• Is the computer’s resolution setting

appropriate?

POWER/STANDBY indicator is

lighted in red.

• Horizontal and / or vertical sync signal is • Check the input signal.

not present when the Intelligent Power

Manager control is on.

POWER/STANDBY indicator is

blinking in red.

• The temperature inside the main unit has • Promptly switch off the power of the main

become too high and has activated the

protector.

unit and wait until the internal temperature

drops. See*1.

POWER/STANDBY indicator is

blinking in green and red, or green.

• Prompty switch off the power of the main

unit. See *2.

——————

Download from Www.Somanuals.com. All Manuals Search And Download.

*1 Overheat protector

If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor

and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location and wait for the monitor

to cool for 60 minutes. If the problem persists, contact your dealer.

*2 In the following case, power off the monitor immediately and contact your dealer or authorized Marantz Service Center.

The monitor turns off 5 seconds after powering on and then the POWER/STANDBY indicator blinks. It indicates that the power supply circuit, plasma

display panel, temperature sensor, or one or more fans have been damaged.

Download from Www.Somanuals.com. All Manuals Search And Download.

Model PD4220V Information

Plasma Monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

Warning

NOTE:

Not for use in a computer room as defined in the Standard

When you connect a computer to this monitor, use an RGB

for the Protection of Electronic Computer/ Data Processing

Equipment ANSI/NFPA 75.

cable including the ferrite core on both ends of the cable.

And regarding DVI and power cable, attach the supplied

ferrite cores. If you do not do this, this monitor will not

conform to mandatory FCC or C-Tick standards.

Attaching the ferrite cores:

Set the ferrite cores on both ends of the DVI cable (not

supplied), and both ends of the power cable (supplied).

Close the lid tightly until the clamps click.

Use the band to fasten the ferrite core (supplied) to the

DVI cable.

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct

the interference at his own expense.

DVI cable (not supplied)

Connector

band

This is a Class A product. In a domestic environment, this

product may cause radio interference in which case the

user may be required to take adequate measures.

core (small)

Power cable (supplied)

core (large)

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommandations importantes

Avertissement

REMARQUE:

Pour raccorder un ordinateur à ce moniteur, procéder à

l’aide d’un câble RGB à âme de ferrite aux deux

Ne pas utiliser dans une salle d’ordinateurs telle que définie

dans la Norme pour la protection des ordinateurs

électroniques/appareils de traitement des données ANSI/

extrémités. Sur les câbles DVI et les câbles d’alimentation

NFPA75.

électrique, fixer les âmes de ferrite fournies aux extrémités.

Si vous ne le faîtes, le moniteur ne sera pas en

DOC avis de conformation

conformité avec les exigences des standards FCC.

Cet appareil numérigue de la Classe A respecte toutes les

Fixation des noyaux en ferrite.

exigences du Réglement sur le Matériel Brouilleur du Canada.

Monter les tores en ferrite aux deux extrêmités du câble

DVI (non fourni) et aux deux extrêmités du câble

d’alimentation électrique (fourni).

Fermez doucement le couvercle jusqu’à ce que les crans

se clipsent.

Fixer le tore en ferrite (fourni) au câble DVI à l’aide d’un

collier.

Câble DVI (non fourni)

Connecteur

Collier

noyau (petit)

Câble d'alimentation

électrique (fourni)

noyau (large)

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Screen Size

36.3"(H)

20.4"(V) inches

921(H)

518(V) mm

diagonal 42"

1.18"

(30)

2.32"

(59)

40" (1018)

Aspect Ratio

Resolution

Pixel Pitch

16 : 9

853(H)

480(V) pixels

36.3" (921)

0.04"(H)

0.04"(V) inches

1.08(H)

1.08(V) mm

Color Reproduction

Signals

256 levels, 16,770,000 colors

Synchronization Range Horizontal : 15.5 to 110 kHz

(automatic : step scan)

Vertical : 50.0 to 120 Hz

(automatic : step scan)

3.5"

(89)

Input Signals

RGB, NTSC (3.58/4.43), PAL (B,G,M,N),

PAL60, SECAM, HD*¹, DVD*¹, DTV*¹

Input Terminals (VIDEO1 and RGB1 can also be used as OUTPUT terminals)

Units are in inch

(mm)

RGB

Visual 1 (Analog) mini D-sub 15-pin

Visual 2 (Analog) BNC (R, G, B, H/CS, V)

1*²

Visual 3 (Digital) DVI-I 24-pin

1*³

The features and specifications may be subject to change without

notice.

Video

Visual 1

Visual 2

Visual 3

BNC

*¹HD/DVD/DTV input signals supported on this

system

RCA-pin

S-Video: DIN 4-pin

480P (60 Hz)

525P (60 Hz)

576P (50 Hz)

625P (50 Hz)

720P (60 Hz)

1080I (50 Hz)

480I (60 Hz)

525I (60 Hz)

576I (50 Hz)

625I (50 Hz)

1035I (60 Hz)

1080I (60 Hz)

DVD/HD/DTV

Visual 1

Visual 2

Audio

RCA-pin (Y, PB[CB], PR[CR])

1*¹

BNC (Y, PB[CB], PR[CR])

1*^1,*²

Stereo RCA

3(Selectable)

D-sub 9-pin

1(RS-232C)

8W+8W at 6 ohm

External Control

Sound output

Power Supply

AC120V 50/60Hz

AC100-240V 50/60Hz 4.5A (maximum)

Current Rating

3.7A (maximum)

*²The 5-BNC connectors are used as RGB/PC2 and

HD/DVD2 input. Select one of them under “BNC

INPUT”.

*³Not compatable with HDCP.

When HDCP encrypted signal is selected, picture is not

produced or disturbed periodically.

Power Consumption

Dimensions

270W (typical)

40 (W)

24 (H)

3.5 (D) inches

1018 (W)

610 (H)

89(D) mm

Weight

Environmental Considerations

62.8 lbs / 28.5 kg (without stand)

Operating Temperature 0°C to 40°C / 32°F to 104°F

Humidity

Altitude

20 to 80% (no condensation)

0 to 9180 feet / 0 to 2800 m

Storage Temperature -10°C to 50°C / 14°F to 122°F

Humidity

Altitude

10 to 90% (no condensation)

0 to 9840 feet / 0 to 3000 m

Other Features Motion compensated 3D Scan Converter (NTSC,

PAL, 480I, 576I, 525I, 625I, 1035I, 1080I), 2-3

pull down Converter (NTSC, 480I, 525I, 1035I,

1080I (60Hz)), 2-2 pull down Converter (PAL,

576I, 625I, NTSC, 480I, 525I), Digital Zoom

Function (100-900% Selectable), Video Wall 2×2/

3×3 multi screen, Self Diagnosis, Anti Image

Burn (PLE LOCK1~3, INVERSE, WHITE,

ORBITER (Auto1,2/Manual), SCREEN WIPER),

Color Temperature select (high/mid/mid low/low,

user has 4 memories), Control lock (Except power

SW), Auto Picture, Input Skip, Color Tune, Low

Tone (3 mode), Auto ID, Programmable Timer,

Gamma Correction (4 mode), Loop through

interface, Plug and play (DDC1, DDC2b, RGB3:

DDC2b only)

Front Panel User Controls Power on/off, Input source select,

Volume up/down, OSM control

Remote Control Functions Power on/off, Input source select, OSM

control,Volume up/down, Cursor (UP,

DOWN,LEFT, RIGHT), Pointer, Zoom up/

down, Off timer, Wireless/Wired remote

control

OSM Functions Picture (Contrast/Brightness/Sharpness/ Color/Tint/

Picture mode/Noise reduction/Color temperature/

White balance/Gamma/Low tone/Color tune), Audio

(Bass/Treble/Balance/Audio input), Image Adjust

(Aspect mode/V-Position /H-Position/V-Height /H-

Width/Auto Picture/Fine picture/Picture adjustment),

Option1 (OSM/BNC Input/D-Sub Input/RGB Select/

HD Select/Input Skip/All Reset), Option2 (Power

management/Cinema mode/Long life [PLE, Orbiter,

Inverse, White, Screen wiper, Soft focus]/Gray level/

S1/S2), Option3 (Timer/Power on mode/Control lock/

IR Remote/Loop out/ID number/Video wall [Divider,

Position, Disp. mode, Auto ID, Image adjust, Power

on delay, PLE link, Timer]), Advanced OSM,

Language*, Color system, Source information

*English, German, French, Italian, Spanish, Swedish,

Chinese

Accessories

Remote control with two AAA batteries, Power

cord, Manuals, Safety metal fitting parts, Ferrite

cores, Bands

Regulations

UL Approved (UL 60950/CSA C22.2

No.60950-00)

DOC Canada requirements

SEMKO Approved(EN60950)

Meets FCC Class A requirements

Meets AS/NZS CISPR 22:2002 Class A

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Signals Supported

ꢀ 42Wide VGA

Supported resolution

•

When the screen mode is NORMAL, each signal is converted to a 640 dots

480 lines signal (42Wide VGA). (Except for *^2,*⁴)

• When the screen mode is FULL, each signal is converted to a 853 dots

480 lines signal (42Wide VGA). (Except for *³)

Computer input signals supported by this system

Sync Polarity

Presence

Screen mode

Vertical

Horizontal

frequency frequency

(Hz) (kHz)

70.1 31.5

RGB

Dots

lines

Model

select*⁵

Memory

NORMAL

Horizontal Vertical Horizontal Vertical

FULL

DVI

Signal Type

(4:3)

YES*²*³

YES*³

– –

(16:9)

YES

YES*³

YES

640

400

– –

STILL

– –

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

NEG

POS

YES

– –

YES

– –

YES

640

480

59.9

72.8

75.0

85.0

100.4

120.4

60.0

56.3

60.3

72.2

75.0

85.1

99.8

120.0

60.0

70.1

75.0

85.0

100.6

75.0

56.2

59.8

60.0

59.9

60.0

75.0

85.0

100.1

60.0

65.0

70.0

75.0

85.0

66.7

74.6

74.9

75.1

60.0

71.2

72.0

66.0

76.0

76.1

60.0

31.5

37.9

37.5

43.3

51.1

61.3

31.0

31.7

35.2

37.9

48.1

46.9

53.7

63.0

75.7

48.4

56.5

60.0

68.7

80.5

67.5

45.1

48.0

47.7

48.3

64.0

80.0

91.1

108.5

75.0

81.3

87.5

93.8

106.3

35.0

49.7

60.2

68.7

64.6

75.1

78.1

61.8

71.7

81.1

49.7

63.9

STILL

– –

848

480

852

480*¹

800

600

WIDE2

WIDE1

STILL

– –

YES

– –

IBM PC/AT

compatible

computers*⁸

– –

1024

768

STILL

– –

STILL

– –

1152

864

STILL

WIDE1

WIDE3

WIDE1

WIDE2

STILL

– –

YES

1280

768

– –

YES

1360

765

1360

768

1376

768

1280

1024

– –

YES

– –

YES*⁴

YES

YES*³

YES

YES*⁴

YES

YES*⁴

YES

YES*⁴

– –

1600

1200

– –

640

480

832

624

– –

Apple

Macintosh*^6,*⁸

Sync on G Sync on G

– –

1024

768

1152

870

1280

1024

WIDE1

– –

Work Station

(EWS4800)

NEG

– –

NEG

– –

YES

– –

YES

– –

YES

– –

Work Station (HP)

1280

1024

– –

Work Station

1152

900

– –

C Sync

– –

C Sync

– –

(SUN)

– –

1280

1024

768

1280

1024

– –

Work Station

(SGI)

– –

YES

– –

IDC-3000G

YES*⁷

– –

NEG

YES

YES*⁷

PAL625P

768

576

50.0

59.9

31.4

31.5

640

480

MOTION

NTSC525P

Download from Www.Somanuals.com. All Manuals Search And Download.

*1 Only when using a graphic accelerator board that is capable of displaying 852

480.

*2 Display only 400 lines (42Wide VGA) with the screen center of the vertical orientation located at the center.

*3 The picture is displayed in the original resolution. The picture will be compressed for other signals.

*4 Aspect ratio is 5:4. This signal is converted to the following signal (42Wide VGA: 600 dots

480 lines).

*5 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the RGB mode

prepared for the input signals listed in the table above.

*6 To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.

*7 Other screen modes (ZOOM and STADIUM) are available as well.

*8 When viewing a moving picture at a vertical frequency greater than 65Hz, the picture may sometimes be unstable (jumpy). If this occurs,

please set the refresh rate of the external equipment to 60Hz.

To view 480I@60Hz (480 interlaced lines, 60Hz refresh rate) or 576I@50Hz (567 interlaced lines, 50Hz refresh rate) when sync polarity

is “Sync on Green”, set “RGB SELECT” to “MOTION”.

NOTE:

• While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the picture or

the fine picture because of errors in synchronization of your computer.

• This monitor has a resolution of 853 dots

480 lines. It is recommended that the input signal should be VGA, wide VGA, or equivalent for

PD4220V.

• With digital input some signals are not accepted.

• The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

• If you are connecting a composite sync signal, use the HD terminal.

• “IBM PC/AT” and “VGA” are registered trademarks of International Business Machines, Inc. of the United States.

• “Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.

Printed in Japan

05BW851010

7S900058

04/2004 ECMar

Download from Www.Somanuals.com. All Manuals Search And Download.

www.marantz.com

You can find your nearest authorized distributor or dealer on our website.

JAPAN

U.S.A.

Marantz Japan, Inc.

Marantz America, Inc.

Marantz Europe B.V.

35-1 Sagami Ohno 7-Chome, Sagamihara-shi, Kanagawa 228-8505, Japan

1100 Maplewood Drive, Itasca, IL 60143, U.S.A.

EUROPE

P.O. Box 8744, 5605 LS Eindhoven, The Netherlands

is a registered trademark.

Printed in Japan

02/2004

ECMar

38AW851022

7S900057

Download from Www.Somanuals.com. All Manuals Search And Download.

Lexmark Printer 248X User Manual
Lindy Switch iSWITCH User Manual
Magnasonic Microwave Oven MMW5736 1 User Manual
Magnavox CRT Television 20MT4405 User Manual
Mark Of Fitness Home Gym XM 4419 User Manual
Master Lock Portable Generator HWI3000 MGH3000 MGH4000C MGH4000CI MGH5000C MGH5000CI MGH5000CIE MGH6000C MGH6000CI MGH7000C MGH7000CI MGH10000 User Manual
Maytag Range W10239459A User Manual
McCulloch Trimmer 249350 User Manual
Melissa Toaster 643 072 User Manual
Mellerware Iron 23465 User Manual