Hedge Trimmer E System
Taille-haie E-System
E-System-Heckenschere
Owners manual and safety instructions
Manuel d’utilisation et consignes de sécurité
Benutzerhandbuch und Sicherheitshinweise
© 2006 Mantis, Div. of Schiller-Pfeiffer Inc. All Rights Reserved.
© 2006 Mantis, Division de Schiller Pfeiffer Inc. Tous droits réservés.
© 2006 Mantis, Division von Schiller Pfeiffer Inc. Alle Rechte vorbehalten.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and warnings
A. Safety labels
READ AND
UNDERSTAND
OPERATOR’S MANUAL
BEFORE USING! KEEP
IN SAFE PLACE!
Please pay particular attention to the warning and information
labels found on various parts of this hedge trimmer attachment
unit. They are an important part of the safety system. These
labels must be replaced in time due to abrasion, etc. It is your
responsibility to replace the labels when they become hard to
read. The location of these labels and their part numbers for
ordering are shown below.
WARNING!
WARNING
–
DANGER
IMPROPER USE OR CARE OF THIS HEDGE
TRIMMER, OR FAILURE TO WEAR PROPER
PROTECTION CAN RESULT IN SERIOUS INJURY.
WEAR EYE AND EAR
PROTECTION
READ AND UNDERSTAND THE RULES FOR SAFE
OPERATION AND ALL INSTRUCTIONS IN THIS
MANUAL.
WARNING!
WEAR EYE AND HEARING PROTECTION,
AND PROPER CLOTHING.
WEAR SLIP-RESISTANT
FOOTWEAR. MAINTAIN
FOOTING AND BALANCE
AT ALL TIMES. DO NOT
STAND ON SLIPPERY,
UNEVEN OR UNSTABLE
SURFACES. DO NOT
WORK IN ODD
POSITIONS OR ON
LADDER. DO NOT OVER
REACH.
KEEP BYSTANDERS AT
A SAFE DISTANCE
DANGER ZONE
SURROUNDING THE
OPERATOR. ONLY THE
OPERATOR SHOULD BE
IN THE DANGER ZONE!
THROWN OBJECTS
P/N 331179
WARNING!
CUTTING HAZARD! KEEP
BOTH HANDS ON HANDLES
AND AWAY FROM BLADES!
P/N 330600
2
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Consider work area environment.
General safety rules
Do not expose power tools to rain. Do not use power tools
in damp or wet locations. Keep work area well lit. Do not
use power tools where there is risk of fire or explosion.
WARNING
–
DANGER
THE BLADES COAST AFTER SWITCH TRIGGER
IS RELEASED AND MOTOR IS SWITCHED OFF.
MAKE SURE BLADES HAVE COME TO A
COMPLETE STOP AND ENGINE IS OFF BEFORE
RELEASING A HANDLE.
3. Guard against electric shock.
Avoid body contact with earthed or grounded surfaces,
e.g. pipes, radiators, stoves, ovens, refrigerators.
4. Keep children away.
Do not let visitors touch the tool or extension cord. All
visitors should be kept away from area. Local regulations
may restrict the age of the operator.
5. Store idle tools.
WARNING
–
DANGER
When not in use, tools should be stored in a dry, high or
locked up place, out of reach of children.
IF TRIMMER IS USED IMPROPERLY OR SAFETY
PRECAUTIONS ARE NOT FOLLOWED, THE
USER RISKS SERIOUS INJURY TO THEMSELVES
AND OTHERS.
6. Do not force the tool.
It will do the job better and safer at the rate for which it
was intended. Walk, never run.
READ AND UNDERSTAND THE FOLLOWING
BEFORE ATTEMPTING TO OPERATE THIS
HEDGE TRIMMER.
7. Use the right tool.
Do not force small tools or attachments to do the job of a
heavy duty tool. Do not use tools for purposes not
intended; for example, do not use chain saw attachment to
cut tree limbs or logs.
Don’t ever grasp cutting blades for any reason.
8. Dress properly.
Don’t attempt to clear cut material while blades are moving,
and the motor is running. Never try to remove jammed material
or adjust the blade angle before switching the motor off and
making sure the blades have stopped completely.
Do not wear loose clothing or jewellery that can be caught
in moving parts. Long trousers, non-slip gloves and sturdy
work shoes with non-skid soles are recommended when
working outdoors. Wear protective hair covering to contain
long hair.
Don’t hold the cutter blades when making any adjustments to
the blade or loop handle positions.
9. Use protective equipment.
Always make sure that the blades are in the correct working
position that you want before starting the motor.
To avoid injury, wear ear, eye protection, face or dust mask
if the operation is dusty. To avoid injury from falling
branches, wear helmet. Eye protection must meet
applicable CE requirements.
Always stop the motor before adjusting the working position
of the cutting device.
10. Do not abuse the cord.
Never carry the tool by the cord or yank it to disconnect it
from the socket. Keep the cord away from heat, oil and
sharp edges.
WARNING
WHEN USING ELECTRIC TOOLS, BASIC SAFETY
PRECAUTIONS, INCLUDING THE FOLLOWING,
SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK AND
PERSONAL INJURY.
11. Maintain tool with care.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubrication and
changing accessories. Inspect tool cord periodically and if
damaged, have it repaired by an authorised service facility.
Inspect extension cords periodically and replace, if
damaged. Keep handles dry, clean and free from oil and
grease.
Pay particular attention to all sections regarding safety.
Read and understand all these instructions before operating this
product and save these instructions. Be familiar with the
controls and the proper use of equipment.
12. Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
For safe operations:
13. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting
1. Keep work area clean.
Cluttered areas and benches invite injuries.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
wrenches are removed from the tool before turning it on.
WARNING
–
DANGER
14. Avoid unintentional starting.
Do not carry a plugged in tool with a finger on the switch
trigger. Ensure switch is off when plugging in.
LITTLE WONDER WILL NOT BE RESPONSIBLE
FOR THE FAILURE OF CUTTING DEVICES OR
ACCESSORIES THAT HAVE NOT BEEN TESTED
AND APPROVED FOR USE WITH THIS UNIT.
USE ONLY MANUFACTURER-RECOMMENDED
REPLACEMENT PARTS.
15. Use outdoor extension leads.
When tool is used outdoors, use only extension cords
intended for outdoor use.
16. Important extension cord information:
19. The use of any accessory or attachment, other than those
recommended in this instruction manual, may present a
risk of personal injury.
a. Make sure the extension cords are in good condition
before use.
b. Based on the total length of cord that you are going
to use, check the chart to make sure the cord meets the
correct minimum cord gauge (AWG) requirements.
20. Have your tool repaired by a qualified person.
This electric tool conforms to relevant safety requirements.
Repairs should only be carried out by qualified persons
using original spare parts, otherwise this may result in
considerable danger to the user.
IMPORTANT NOTE:
Using an undersized cord or a larger number cord gauge
(AWG) than recommended in the chart, will cause a loss in
power and overheating of the unit. Using a smaller number
cord gauge (AWG) than recommended in the chart, is
acceptable.
21. Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
22. Work only in daylight or in good artificial light.
23. Keep all guards attached at all times when unit is operated.
24. Always use the shoulder strap.
Adjust the strap for comfort before starting the engine.
Extension cord chart (minimum cord gauge (AWG))
25. Secure unit during transport to prevent damage or injury.
Length (metres)
.3 to 7.8 7.9 to 15.5 15.6 to 30.6 30.7 to 45.7
18 16 14 12
26. Machine should not be used in any position that causes
any part to come within 3 metres of overhead electrical
lines. Always be aware of overhead power lines.
Cord gauge (AWG)
17. Stay alert.
Watch what you are doing. Use common sense. Do not
operate tool when you are tired, ill or under the influence
of alcohol or other drugs.
27. Always keep a firm grip on both handles when motor is
running: one hand grasps the front “loop” handle while the
other hand grasps the rear handle. Severe injuries can
result if you try to use this machine with only one hand or
with an insecure grip.
18. Check damaged parts.
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it
will operate properly and perform its intended function.
Check for alignment of moving parts, free running of
moving parts, breakage of parts, mounting and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorised service centre unless otherwise
indicated in this instruction manual. Have defective
switches replaced by an authorised service facility. Do not
use the tool if the switch does not turn it on and off.
28. Thoroughly inspect the area where equipment is to be
used and removed all objects, which can be thrown by the
machine.
29. Always keep area clear of children, pets, and bystanders.
30. Always inspect your unit before each use and ensure that
all handles, guards and fasteners are secure, operating, and
in place. Be sure that all electrical cords are not damaged
or broken.
31. Always maintain and examine your attachments with care.
Follow maintenance instructions given in manual.
Don’t operate the machine with a damaged or excessively
worn cutting device.
32. Don’t attempt to repair any part of the extended reach “E”
system. Have repairs made by a qualified repairman. See
that only original “Mantis” parts are used.
33. Maintain a firm footing and good balance, do not
overreach while trimming. Before you start to trim, check
4
Download from Www.Somanuals.com. All Manuals Search And Download.
the work area for obstacles that might cause you to lose
your footing, balance or control of the machine. While
operating the machine always be sure of a safe and secure
operating position especially when using steps or a ladder.
Always be sure of your footing on slopes.
Attaching the Hedge Trimmer
No tools are required to attach the Hedge Trimmer to the
power head.
1. Pull the spring pin up on the adapter of the power head
shaft assembly.
2. Carefully fit hedge trimmer drive shaft into adapter,
making sure that male spline of the inner drive shaft
engages into the female spline socket of the power head
shaft. (Picture 1)
WARNING
–
DANGER
IMPROPER ASSEMBLY OF THIS EQUIPMENT
CAN RESULT IN SERIOUS INJURY. MAKE SURE
TO FOLLOW ALL INSTRUCTIONS CAREFULLY.
IF YOU HAVE ANY QUESTIONS, CONTACT YOUR
LOCAL AUTHORISED MANTIS DEALER.
3. When the drive shaft is properly aligned, the spring pin
will drop into the hole on the shaft of the hedge trimmer
attachment. A click should be heard when completed.
4. Insure two shaft parts are fully engaged by twisting them.
Full engagement will prevent shaft rotation.
34. Always disconnect power cord from power source:
a. Before cleaning blockages.
5. Secure assembly by tightening the knob. (Picture 2)
b. Before checking, cleaning or working on the
cutting portion of the unit.
6. Unit handles can be re-adjusted to the operator’s
preference by simply loosening the screws and sliding
handles up or down the shaft.
c. After striking a foreign object: inspect the cutting
part for damage and make repairs before restarting
and operating the unit.
d. If machine starts to vibrate abnormally (check
immediately).
e. Whenever you leave the unit.
35. Securing the extension cord.
Bend the extension cord about 40cm from the plug end.
Push that bend through the oblong opening, then loop the
bend under the cord retaining clips as shown. This will
prevent the extension cord from detaching from the hedge
trimmer plug.
Picture 1
Picture 2
Balancing the Unit
Check the balance of the assembled unit. The handles and
shoulder harness have been assembled at the factory and set
according to the average size person. This can be adjusted to
the operator’s preference by simply loosening the screws and
sliding the handle up or down the shaft. Make sure to retighten
the screws before operating hedge trimmer.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimming
Adjusting the blade angle
WARNING
–
DANGER
WARNING
DANGER
BLADES COAST AFTER RELEASING THROTTLE
OR STOPPING MOTOR.
SWITCH OFF THE MOTOR AND UNPLUG
THE UNIT BEFORE LUBRICATING OR
ADJUSTING THE BLADES.
KEEP A FIRM GRIP WITH BOTH HANDS WHILE
BLADES ARE MOVING AND/OR MOTOR IS
RUNNING.
1. To adjust the blade angle, first shut off the motor. Next, grip
the blade adjustment handle. Then move the quick release
lever from the tight position, at the right angle, so that it is
pointing straight out.
KEEP A SURE FOOTING. DO NOT OVERREACH.
IF YOUR TRIMMER BECOMES JAMMED,
RELEASE SWITCH AND STOP MOTOR. MAKE
SURE BLADES HAVE STOPPED COMPLETELY.
WARNING
–
DANGER
UNPLUG THE UNIT, THEN REMOVE
THE OBSTRUCTION.
DO NOT ADJUST BLADE ANGLE BY GRASPING
THE BLADES. BLADES ARE SHARP AND YOU
RISK INJURY TO YOURSELF.
1. Do not start the motor until you are familiar with your
hedge trimmer and all of its controls and functions.
2. The blade will now adjust freely to any position up to 180˚.
3. Use the adjustment handle located beneath the assembly to
move the blade to the desired angle position.
2. Plug in the unit and grasp the handles securely. One hand
grasps the front loop handle, while the other hand grasps the
switch handle. With both hands on the handles, push lockout
trigger button with your thumb and then squeeze trigger to
engage the blades. Start cutting when motor runs at full RPM.
4. Once the desired angle has been achieved, simply move the
quick release lever back to the tight position.
WARNING
–
DANGER
0.3 cm
0.6 cm
DO NOT OPERATE UNIT UNLESS QUICK RELEASE
LEVER IS IN THE “TIGHTENED” POSITION.
Quick release
lever
1.25 cm
Lockout trigger button
Trigger
3. Tilt the trimmer so the cutting teeth are angled slightly
toward the hedge or shrub and proceed to cut. Use
overlapping sweeping motions away from your body to
achieve a safe and even cut.
4. This unit is designed to cut any type of hedge or shrub with
a branch thickness under 1/2” in (13 mm) diametre (see
below). The depth of each cut depends on the hardness of
the wood.
Blade
adjustment handle
THICKNESS OF CUT SHOULD NOT EXCEED
13mm (1/2 inch) IN DIAMETRE.
Misuse of this hedge trimmer will void the warranty, i.e.:
Cutting hedges or shrubs over 13mm (1/2”) diametre or
foreign objects such as wires, rocks or fences. Before trimming,
check work area for foreign objects such as wires, cords, glass,
fences, or rocks. Be sure to remove any foreign objects from
the work area. Failure to properly maintain this hedge trimmer
will void the warranty.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
WARNING
–
DANGER
SWITCH OFF THE ENGINE BEFORE LUBRICATING
OR ADJUSTING THE BLADES.
Blades adjustment
The care and adjustment of the blades is very important to the
efficient operation of the trimmer and especially to the long
life of the motor.
When resting, it is often a good idea to use the time to oil the
cutting blades.
If a gap exists between the upper and lower blades, follow the
procedure below to adjust them so that they fit more closely
together.
1. Loosen lock nut.
2. Tighten screw fully, and then turn one-third to one-half of
a rotation backward.
3. While holding onto the screw to keep it in position, tighten
the lock nut.
4. Check to make sure that the flat washer is loose enough so
that it may be turned by pressing on it with a finger.
NOTE: Correct blade adjustment can only be achieved on
clean, oiled blades. Screwing in the screw too tightly may
make it impossible for the blades to move. Conversely, not
screwing in the screw tightly enough may make the blades of
the trimmer feel dull and cause leaves and branches to become
caught in the blades of the trimmer.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Maintenance
WARNING
–
DANGER
checked for proper amount (approximately 1/2 full in the
area of the gears) and a new gasket should be used to
insure proper seating of the cover plate. Grease should be
added every 25 hours of use. Use EP2 white lithium grease
in the gear housing.
UNPLUG THE UNIT BEFORE LUBRICATING
OR ADJUSTING THE BLADES.
A. Lubrication
4. Lubricate male spline part of the drive shaft with EP2
White Lithium grease.
1. A few drops of light No. 10 oil should be placed on the
back edge of each adjusting screw head approximately
after every 4 hours of normal operation.
B. Storage
2. To obtain trouble free trimming, it is necessary to keep the
blades lubricated and clean. The gum that collects and
builds up on the blades can be removed with a 50-50
mixture of kerosene and No. 10 oil. As petroleum products
can shorten the life of some plastics, it is necessary to
remove excess oil-kerosene mixture from the plastic parts.
1. Store your trimmer in a dry and dust free space, out of the
reach of children.
2. Clean the blades thoroughly and coat them with No. 10 oil
to prevent rust.
3. Perform all required maintenance and service found in this
manual.
3. When blades are replaced, or any other time that the
bottom cover plate is removed, the grease level should be
4. Use blades cover.
Service maintenance guide
Area
Maintenance
Before Every 25 Every 50 Every 100
use
Note
hours
hours
hours
Cutting parts
Gear case
Replace if
something is wrong
ꢀ
Grease
ꢀ
Use EP2 white
Lithium grease
Screws, nuts
bolts
Tighten, replace
ꢀ
ꢀ
ꢀ
ꢀ
Not adjusting
screws
Spline (male) Lubricate
Use EP2 white
Lithium grease
Blades
Oiling
Light #10 oil
IMPORTANT: Time intervals shown are maximum. Actual use and your experience will determine the frequency of
required maintenance.
Area
Maintenance procedure
Inspect/lubricate
Frequency
Spline male/female
connection of the
inner drive shaft
1. Remove the side screw, and loosen
up other three as shown on the
diagram (left).
2. Pull the shaft from the gear housing.
3. Pull and clean internal shaft.
4. Lubricate.
20-25 hrs
5. Re-install the drive shaft.
6. Do not allow any dirt and dust
on the internal drive shaft
Lubricate
7. Do not allow any dirt and dust
entering into the gear case
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Hedge trimmer E System exploded view
58
62
59
60
55
61
56
25
54
53
52
22
51
50
14
15
20
19
12
49
16
13
63
9
17
48
18
47
7
1
6
45
5
1
19
20
30
4
8
44
21
25
3
42
43
22
2
23
57
25
26
27
24
42
28
29
41
40
30
31
32
33
38
37
38
39
34
36
35
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Hedge trimmer E System parts list
KEY #
DESCRIPTION
PART #
QTY
KEY #
DESCRIPTION
PART #
QTY
1
2
LOCKNUT INSERT
LOCKING KNOB
331534
331218
1
1
1
1
5
1
1
1
1
2
2
1
2
1
2
1
1
1
1
1
1
2
1
1
3
1
1
1
1
2
2
32
33
34
35
36
37
38
39
40
41
42
43
44
45
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
GASKET
331233
1
1
1
4
1
1
5
4
2
1
5
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
GEAR CASE BOTTOM COVER 331234
3
ADJUSTMENT BRACKET 331217
CLAMPING PAD 331535
PLASTIC LOCKING SPACER 331218
PROTECTIVE COVER
BOLT M5X18
FELT
331235
331547
331236
331548
331549
331550
331551
331237
331545
331238
331539
331552
331240
331241
331242
331243
331244
331245
331246
331553
331554
331555
331247
4
5
6
ROTATE BOLT
RIVET
331536
331537
331538
331219
331539
331540
331220
331541
SCREW M6X20
WASHER
7
8
FLAT WASHER
CLAMPING LEVER
NUT M5
SCREW M6X18
FRAME BAR SCREW
FRAME BAR
NUT M6
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
LOCK WASHER
HANDLE
FRAME BAR BRACE
NUT M5
BOLT M5X20
CUTTING HAZARD LABEL 330600
SCREW M4X8 331542
GEAR CASE TOP COVER 331221
SNAP RING
DUAL GEAR
DRIVE SHAFT
GEAR CASE (B)
PINION GEAR
BEARING 619017
SNAP RING
SNAP RING
GEAR
331222
331223
331224
331225
331226
331543
331544
331545
331227
331228
331229
331230
331546
331231
331232
SNAP RING
BEARING 6000-2Z
GEAR CASE (A)
FLAT WASHER
LOCK WASHER
NUT M6
SNAP RING
BOLT M6X14
BOLT M6X30
BOLT M5X12
BLADE COVER
GREASE FITTING
HARDENED SHIM
PLATE
OUTER SHAFT 24X623MM 331248
INTERNAL SHAFT ADAPTER 331249
INTERNAL SHAFT 628X7MM 331250
CRANK SHAFT
SNAP RING
SPACER
WARNING LABEL
O-RING
331251
331179
BEARING 608-2Z
BLADE ASSEMBLY
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2 YEAR LIMITED SERVICE & WARRANTY POLICY
FOR ELECTRIC HEDGE TRIMMER
MANTIS extends this limited warranty against defects in material and workmanship for
a period of two years from the date of purchase, to the first retail purchaser and each
subsequent owner during the warranty period. This warranty covers all portions of the
MANTIS “E” System Hedge Trimmer.
MANTIS will repair or replace, at its option, any part or parts of the product proven to
be defective in material or workmanship under normal usage during the warranty period.
Warranty repairs and replacements will be made without charge for parts or labor. All
parts replaced under warranty will be considered as part of the original product, and any
warranty on the replaced parts will expire coincident with the original product warranty.
In the event of a defect or malfunction, the purchaser must send the product, postage
paid to:
Mantis
2800 Turnpike Dr.
Suite #1
2800 Commerce Center
Hatboro, PA 19040
MANTIS assumes no responsibility in the event that the product was assembled or used in
noncompliance with any assembly, care, safety, or operating instructions contained in the
Owner’s Manual; was not used with reasonable care; or was misused, used for other than
normal or intended purposes. This warranty does not extend to parts affected or damaged
by normal wear and tear.
MANTIS MAKES NO EXPRESS OR IMPLIED WARRANTIES OR REPRESENTATIONS
EXCEPT THOSE CONTAINED HEREIN. THE DURATION OF ANY IMPLIED
WARRANTY, INCLUDING MERCHANTABILTY AND FITNESS FOR A PARTICULAR
PURPOSE, IS LIMITED TO THE DURATION OF THIS WRITTEN LIMITED
WARRANTY. MANTIS DISCLAIMS ALL LIABILITY FOR INDIRECT AND/OR
CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THAT ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
MANTIS
1028 Street Road
Southampton , PA 18966
+ (215) 355-9700
Specifications, descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTIS
1028 Street Road
Southampton , PA 18966
+ (215) 355-9700
P/N 331708
7/06 REV B
Download from Www.Somanuals.com. All Manuals Search And Download.
|