Cordless Slide
Compound Saw
Equipped with Electric Blade Brake
190 mm (7-1/2”)
MODEL BLS712
002165
I N S T R U C T I O N M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Download from Www.Somanuals.com. All Manuals Search And Download.
For Your Own Safety Read Instruction Manual
Before Operating Tool
Save it for future reference
GENERAL SAFETY PRECAUTIONS
USA005-1
(For All TOOIS)
1. KNOW YOUR POWER TOOL. Read the
owner’s manual carefully. Learn the tool’s
applications and limitations, as well as the
specific potential hazards peculiar to it.
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Nonslip footwear
is recommended. Wear protective hair
covering to contain long hair.
2. KEEP GUARDS IN PLACE and in working
order.
11. ALWAYS USE SAFETY GLASSES. Also
use face or dust mask if cutting operation
is dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT
safety glasses.
3. REMOVE
ADJUSTING
KEYS
AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning it on.
4. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
12. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than
using your hand and it frees both hands
to operate tool.
5. DON’T USE IN DANGEROUS ENVIRON-
MENT. Don’t use power tools in damp or
wet locations, or expose them to rain.
Keep work area well lighted. Don’t use
tool in presence of flammable liquids or
gases.
13. DON’T OVERREACH. Keep proper footing
and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools
sharp and clean for best and safest perfor-
mance. Follow instructions for lubricating
and changing accessories.
6. KEEP CHILDREN AWAY. All visitors
should be kept safe distance from work
area.
15. DISCONNECT BATTERY FROM TOOL
before servicing; when changing acces-
sories such as blades, bits, cutters, and
the like.
7. MAKE WORKSHOP KID PROOF with pad-
locks, master switches, or by removing
starter keys.
8. DON’T FORCE TOOL. It will do the job bet-
ter and safer at the rate for which it was
designed.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in off
position before inserting battery.
9. USE RIGHT TOOL. Don’t force tool or
attachment to do a job for which it was not
designed.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recom-
mended accessories. The use of improper
accessories may cause risk of injury to
persons.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
18. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.
affect its operation. A guard or other part
that is damaged should be properly
repaired or replaced.
19. CHECK DAMAGED PARTS. Before further
use of the tool, a guard or other part that
is damaged should be carefully checked
to determine that it will operate properly
and perform its intended function - check
for alignment of moving parts, binding of
moving parts, breakage of parts, mount-
ing, and any other conditions that may
20. DIRECTION OF FEED. Feed work into a
blade or cutter against the direction of
rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN POWER OFF. Don’t leave
tool until it comes to a complete stop.
ADDITIONAL SAFETY RULES
USB033-2
DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to slide compound saw
safety rules. If you use this tool unsafely or incorrectly, you can
suffer serious personal injury.
1. Wear eye protection.
8. To reduce the risk of injury, return car-
riage to the full rear position after each
crosscut operation.
2. Keep hands out of path of saw blade.
Avoid contact with any coasting blade. It
can still cause severe injury.
9. Always secure all moving portions before
carrying the tool.
3. Do not operate saw without guards in
place. Check blade guard for proper clos-
ing before each use. Do not operate saw if
blade guard does not move freely and
close instantly. Never clamp or tie the
blade guard into the open position.
10. Stopper pin which locks the cutter head
down is for carrying and storage pur-
poses only and not for any cutting opera-
tions.
11. Be aware that this tool is always in an
operating condition, because it does not
have to be plugged into an electrical out-
let.
4. Do not perform any operation freehand.
The workpiece must be secured firmly
against the turn base and guide fence with
a vise during all operations. Never use
your hand to secure the workpiece.
12. Do not use the tool in the presence of
flammable liquids or gases.
5. Never reach around saw blade.
13. Check the blade carefully for cracks or
6. Turn off tool and wait for saw blade to
stop before moving workpiece or chang-
ing settings.
damage
before
operation.
Replace
cracked or damaged blade immediately.
Gum and wood pitch hardened on blades
slows saw and increases potential for
kickback. Keep blade clean by first remov-
ing it from tool, then cleaning it with gum
7. Remove battery from tool before changing
blade or servicing.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
and pitch remover, hot water or kerosene.
Never use gasoline to clean blade.
25. Wait until the blade attains full speed
before cutting.
14. While making a slide cut, KICKBACK can
occur. KICKBACK occurs when the blade
binds in the workpiece during a cutting
operation and the saw blade is driven
back rapidly towards the operator. Loss of
control and serious personal injury can
result. If blade begins to bind during a cut-
ting operation, do not continue to cut and
release switch immediately.
26. Stop operation immediately if you notice
anything abnormal.
27. Do not attempt to lock the trigger in the on
position.
28. Be alert at all times, especially during
repetitive, monotonous operations. Do
not be lulled into a false sense of security.
Blades are extremely unforgiving.
15. Use only flanges specified for this tool.
29. Always use accessories recommended in
this manual. Use of improper accessories
such as abrasive wheels may cause an
injury.
16. Be careful not to damage the arbor,
flanges (especially the installing surface)
or bolt. Damage to these parts could
result in blade breakage.
30. NEVER hold workpiece on right side of
blade with left hand or vice versa. This is
called cross-armed cutting and exposes
user to risk of SERIOUS PERSONAL
INJURY as shown in the figure. ALWAYS
use vise to secure workpiece.
17. Make sure that the turn base is properly
secured so it will not move during opera-
tion. Use the holes in the base to fasten
the saw to a stable work platform or
bench. NEVER use tool where operator
positioning would be awkward.
18. For your safety, remove the chips, small
pieces, etc. from the table top before oper-
ation.
19. Avoid cutting nails. Inspect for and
remove all nails from the workpiece
before operation.
31. NEVER stack workpieces on the table top
to speed cutting operations. Cut only one
piece at a time.
20. Make sure the shaft lock is released
before the switch is turned on.
21. Be sure that the blade does not contact
the turn base in the lowest position.
32. Some material contains chemicals which
may be toxic. Take caution to prevent dust
inhalation and skin contact. Follow mate-
rial supplier safety data.
22. Hold the handle firmly. Be aware that the
saw moves up or down slightly during
start-up and stopping.
23. Make sure the blade is not contacting the
workpiece before the switch is turned on.
24. Before using the tool on an actual work-
piece, let it run for a while. Watch for
vibration or wobbling that could indicate
poor installation or a poorly balanced
blade.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
USC002-3
1. SAVE THESE INSTRUCTIONS- This man-
ual contains important safety and operat-
ing instructions for battery charger.
6. To reduce risk of damage to electric plug
and cord, pull by plug rather than cord
when disconnecting charger.
2. Before using battery charger, read all
instructions and cautionary markings on
(1) battery charger, (2) battery, and (3)
product using battery.
7. Make sure cord is located so that it will
not be stepped on, tripped over, or other-
wise subjected to damage or stress.
8. An extension cord should not be used
unless absolutely necessary. Use of
improper extension cord could result in a
risk of fire and electric shock. If extension
cord must be used, make sure:
3. CAUTION - To reduce risk of injury, charge
only MAKITA rechargeable batteries
marked on the charger label. Other types
of batteries may burst causing personal
injury and damage.
a. That pins on plug of extension cord
are the same number, size, and shape
as those of plug on charger;
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended
or sold by the battery charger manufac-
turer may result in a risk of fire, electric
shock, or injury to persons.
b. That extension cord is properly wired
and in good electrical condition; and
c. That wire size is at least as large as
the one specified in the table below.
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS
Length of Cord (Feet)
AWG Size of Cord
25
18
50
18
100
18
150
16
9. Do not operate charger with damaged
cord or plug - replace them immediately.
11. Do not disassemble charger or battery
cartridge; take it to a qualified serviceman
when service or repair is required. Incor-
rect reassembly may result in a risk of
electric shock or fire.
10. Do not operate charger if it has received a
sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualified
serviceman.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
12. To reduce risk of electric shock, unplug
charger from outlet before attempting any
maintenance or cleaning. Turning off con-
trols will not reduce this risk.
15. If operating time has become excessively
shorter, stop operating immediately. It
may result in a risk of overheating, possi-
ble burns and even an explosion.
13. The battery charger is not intended for
use by young children or infirm persons
without supervision.
16. If electrolyte gets into your eyes, rinse
them out with clear water and seek medi-
cal attention right away. It may result in
loss of your eyesight.
14. Young children should be supervised to
ensure that they do not play with the bat-
tery charger.
ADDITIONAL SAFETY RULES FOR CHARGER &
BATTERY CARTRIDGE
1. Do not charge Battery Cartridge when
temperature is BELOW 10°C (50°F) or
ABOVE 40°C (104°F).
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
2. Do not attempt to use a step-up trans-
former, an engine generator or DC power
receptacle.
5. Do not store the tool and Battery Car-
tridge in locations where the temperature
may reach or exceed 50°C (122°F).
3. Do not allow anything to cover or clog the
charger vents.
6. Do not incinerate the Battery Cartridge
even if it is severely damaged or is com-
pletely worn out. The battery cartridge can
explode in a fire.
4. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
7. Be careful not to drop, shake or strike bat-
tery.
(2) Avoid storing battery cartridge in a
container with other metal objects
such as nails, coins, etc.
8. Do not charge inside a box or container of
any kind. The battery must be placed in a
well ventilated area during charging.
(3) Do not expose battery cartridge to
water or rain.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following show the symbols used for the charger. Be sure that you understand their
meaning before use.
.......... Ready to charge
.............Charging
...........Delay charge (Cooling)
........Defective battery
....Conditioning
.............Charging complete
...........Cooling abnormality
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Bench mounting
INSTALLATION
002193
When the tool is shipped, the handle is locked in the lowered
position by the stopper pin. Release the stopper pin by lower-
ing the handle slightly and pulling the stopper pin.
1
1. Stopper Pin
002194
This tool should be bolted with two bolts to a level and stable
surface using the bolt holes provided in the tool’s base. This
will help prevent tipping and possible injury.
1
1. Bolt
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
001803
Installing or removing battery cartridge
31
•
•
•
Always switch off the tool before insertion or removal of
the battery cartridge.
2
To remove the battery cartridge, withdraw it from the tool
while sliding the button on the side of the cartridge.
To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If you can see the red part on the
upper side of the button, it is not locked completely.
Insert it fully until the red part cannot be seen. If not, it
may accidentally fall out of the tool, causing injury to you
or someone around you.
1. Button
2. Battery cartridge
3. Red part
•
Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
001336
Charging
2
1. Plug the battery charger into the proper AC voltage
source. Two charging lights will flash in green color
repeatedly.
1
3
2. Insert the battery cartridge into charger until it stops
adjusting to the guide of charger. Terminal cover of
charger can be opened with inserting and closed with
pulling out the battery cartridge.
4
1. Terminal cover
2. Battery cartridge
3. Charging light
4. Battery charger
3. When the battery cartridge is inserted, the charging light
color will change from green to red and charging will
begin. The charging light will keep lighting up lit steadily
during charging. One red charging light indicates
charged condition in 0 - 80% and two red ones indicates
80 - 100%.
4. With finish of charge, the charging lights will change
from two red ones to two green ones.
5. If you leave the battery cartridge in the charger after the
charging cycle is complete, the charger will switch into
its “ trickle charge (maintenance charge)” mode which
will last approximately 24 hours.
6. After charging, unplug the charger from the power
source.
NOTE:
•
•
The battery charger is for charging Makita battery
cartridge. Never use it for other purposes or for other
manufacturer’s batteries.
When you charge a new battery cartridge or a battery
cartridge which has not been used for a long period of
time, it may not accept a full charge. This is a normal
condition and does not indicate a problem. You can
recharge the battery cartridge fully after discharging it
completely and recharging a couple of times.
•
If you charge a battery cartridge from a just operated
tool or battery cartridge which has been left in a location
exposed to direct sunlight for a long time, the charging
light may flash in red color. If this occurs, wait for a while.
Charging will begin after the battery cartridge is cooled
by the cooling fan installed in the charger. When the
temperature on battery is more than approx. 70°C, two
charging lights may flash in red color, and when approx.
50°C - 70°C, one charging light in red color.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
•
If the charging light flashes alternately in green and red
color, charging is not possible. The terminals on the
charger or battery cartridge are clogged with dust or the
battery cartridge is worn out or damaged.
Cooling system
•
This charger is equipped with cooling fan for heated
battery in order to enable the battery to prove its own
performance. Sound of cooling air comes out during
cooling, which means no trouble on the charger.
•
Yellow light will flash for warning in the following cases.
- Trouble on cooling fan
- Incomplete cool down of battery, such as, being
clogged with dust
The battery can be charged in spite of the yellow
warning light. But the charging time will be longer than
usual in this case.
•
•
Check the sound of cooling fan, vent on the charger and
battery, which can be sometime clogged with dust.
The cooling system is in order although no sound of
cooling fan comes out, if the yellow warning light will not
flash.
•
•
Always keep clean the vent on charger and battery for
cooling.
The products should be sent to repair or maintenance, if
the yellow warning light will frequently flash.
Conditioning charge
Conditioning charge can extend the life of battery by auto-
matically searching the optimum charging condition for the
batteries in every situations.
The battery employed in the following conditions repeatedly,
will be worn out shortly, and yellow warning light may flash.
1. Recharge of battery with its high temperature
2. Recharge of battery with its low temperature
3. Recharge of full charged battery
4. Over-discharge of battery (continue to discharge battery
in spite of down of power.)
The charging time of such battery is longer than usual.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Trickle charge (Maintenance charge)
If you leave the battery cartridge in the charger to prevent
spontaneous discharging after full charge, the charger will
switch into its “trickle charge (maintenance charge)” mode
and keep the battery cartridge fresh and fully charged.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely dis-
charged.
Always stop tool operation and charge the battery car-
tridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at
10°C - 40°C (50°F - 104°F).
Let a hot battery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery cartridge when
you do not use it for more than six months.
002245
Blade guard
When lowering the handle, the blade guard rises automati-
cally. The guard is spring loaded so it returns to its original
position when the cut is completed and the handle is raised.
NEVER DEFEAT OR REMOVE THE BLADE GUARD OR
THE SPRING WHICH ATTACHES TO THE GUARD.
1
In the interest of your personal safety, always maintain the
blade guard in good condition. Any irregular operation of the
blade guard should be corrected immediately. Check to
assure spring loaded return action of guard. NEVER USE
THE TOOL IF THE BLADE GUARD OR SPRING ARE DAM-
AGED, FAULTY OR REMOVED. DOING SO IS HIGHLY
DANGEROUS AND CAN CAUSE SERIOUS PERSONAL
INJURY.
1. Blade guard
If the see-through blade guard becomes dirty, or sawdust
adheres to it in such a way that the blade is no longer easily
visible, remove the battery cartridge and clean the guard
carefully with a damp cloth. Do not use solvents or any petro-
leum-based cleaners on the plastic guard.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
001782
If the blade guard is especially dirty and vision through the
guard is impaired, use the supplied socket wrench to loosen
the hex bolt holding the center cover. Loosen the hex bolt by
turning it counterclockwise and raise the blade guard and
center cover. With the blade guard so positioned, cleaning
can be more completely and efficiently accomplished. When
cleaning is complete, reverse procedure above and secure
bolt. Do not remove spring holding blade guard. If guard
becomes discolored through age or UV light exposure, con-
tact a Makita service center for a new guard. DO NOT
DEFEAT OR REMOVE GUARD.
1
1. Blade guard
002195
Positioning kerf board
This tool is provided with the kerf boards in the turn base to
minimize tearing on the exit side of a cut. The kerf boards are
factory adjusted so that the saw blade does not contact the
kerf boards. Before use, adjust the kerf boards as follows:
1
First, remove the battery cartridge. Loosen all the screws
(2 each on left and right) securing the kerf boards. Re-tighten
them only to the extent that the kerf boards can still be easily
moved by hand. Lower the handle fully and push in the stop-
per pin to lock the handle in the lowered position. Loosen the
clamp screw which secures the slide poles. Pull the carriage
toward you fully. Adjust the kerf boards so that the kerf
boards just contact the sides of the blade teeth. Tighten the
front screws (do not tighten firmly). Push the carriage toward
the guide fence fully and adjust the kerf boards so that the
kerf boards just contact the sides of blade teeth. Tighten the
rear screws (do not tighten firmly).
2
1. Clamp screw
2. Kerf board
001800
1
2
3
4
5
After adjusting the kerf boards, release the stopper pin and
raise the handle. Then tighten all the screws securely.
1. Saw blade
2. Blade teeth
3. Kerf board
4. Left bevel cut
5. Straight cut
CAUTION:
•
Before and after changing the bevel angle, always adjust
the kerf boards as described above.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
002196
Maintaining maximum cutting capacity
1
This tool is factory adjusted to provide the maximum cutting
capacity for a 190 mm (7-1/2”) saw blade.
When installing a new blade, always check the lower limit
position of the blade and if necessary, adjust it as follows:
First, remove the battery cartridge. Push the carriage toward
the guide fence fully and lower the handle completely. Use
the socket wrench to turn the adjusting bolt until the periph-
ery of the blade extends slightly below the top surface of the
turn base at the point where the front face of the guide fence
meets the top surface of the turn base.
3
2
1. Adjusting bolt
2. Guide fence
3. Turn Base
001540
With the battery cartridge removed, rotate the blade by hand
while holding the handle all the way down to be sure that the
blade does not contact any part of the lower base. Re-adjust
slightly, if necessary.
2
1
CAUTION:
3
•
After installing a new blade, always be sure that the
blade does not contact any part of the lower base when
the handle is lowered completely. Always do this with the
battery cartridge removed.
1. Top surface ot turn base
2. Periphery of blade
3. Guide fence
002241
Stopper arm
1
The lower limit position of the blade can be easily adjusted
with the stopper arm. To adjust it, move the stopper arm in
the direction of the arrow as shown in the figure. Adjust the
adjusting screw so that the blade stops at the desired posi-
tion when lowering the handle fully.
2
1. Adjusting screw
2. Stopper arm
14
Download from Www.Somanuals.com. All Manuals Search And Download.
002197
Adjusting the miter angle
1
Loosen the grip by turning counterclockwise. Turn the turn
base while pressing down the lock lever. When you have
moved the grip to the position where the pointer points to the
desired angle on the miter scale, securely tighten the grip
clockwise.
5
4
2
3
CAUTION:
1. Turn base
2. Miter scale
3. Pointer
•
•
When turning the turn base, be sure to raise the handle
fully.
4. Grip
After changing the miter angle, always secure the turn
base by tightening the grip firmly.
5. Lock lever
002198
Adjusting the bevel angle
To adjust the bevel angle, loosen the lever at the rear of the
tool counterclockwise.
Push the handle to the left to tilt the saw blade until the
pointer points to the desired angle on the bevel scale. Then
tighten the lever clockwise firmly to secure the arm.
1
CAUTION:
1. Lever
•
•
•
When tilting the saw blade, be sure to raise the handle
fully.
002199
After changing the bevel angle, always secure the arm
by tightening the lever clockwise.
1
When changing bevel angles, be sure to position the kerf
boards appropriately as explained in the “Positioning kerf
boards” section.
3
2
1. Pointer
2. Bevel scale
3. Arm
001811
Switch action
CAUTION:
1
2
•
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the “OFF” position when
released.
•
When not using the tool, remove the lock-off button and
store it in a secure place. This prevents unauthorized
operation.
1. Lock-off button
2. Switch trigger
15
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Do not pull the switch trigger hard without pressing in the
lock-off button. This can cause switch breakage.
To prevent the switch trigger from being accidentally pulled, a
lock-off button is provided. To start the tool, press in the lock-
off button and pull the switch trigger. Release the switch trig-
ger to stop.
WARNING:
•
•
NEVER use tool without a fully operative switch trigger.
Any tool with an inoperative switch is HIGHLY
DANGEROUS and must be repaired before further
usage.
For your safety, this tool is equipped with a lock-off
button which prevents the tool from unintended starting.
NEVER use the tool if it runs when you simply pull the
switch trigger without pressing the lock-off button.
Return tool to a Makita service center for proper repairs
BEFORE further usage.
•
NEVER tape down or defeat purpose and function of
lock-off button.
Electric brake
This tool is equipped with an electric blade brake. If the tool
consistently fails to quickly stop blade after switch trigger
release, have tool serviced at a Makita service center.
The blade brake system is not a substitute for blade guard.
NEVER USE TOOL WITHOUT A FUNCTIONING BLADE
GUARD. SERIOUS PERSONAL INJURY CAN RESULT.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
002200
Socket wrench storage
1
2
The socket wrench is stored as shown in the figure. When
using the socket wrench, pull it out of the wrench holder.
After using the socket wrench, return it to the wrench holder.
3
1. Arm
2. Wrench holder
3. Socket wrench
Installing or removing saw blade
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before installing or
removing the blade.
•
Use only the Makita socket wrench provided to install or
remove the blade. Failure to do so may result in
overtightening or insufficient tightening of the hex bolt.
This could cause an injury.
002193
Lock the handle in the raised position by pushing in the stop-
per pin.
1
1. Stopper Pin
002215
To remove the blade, use the socket wrench to loosen the
hex bolt holding the center cover by turning it counterclock-
wise. Raise the blade guard and center cover.
1
2
4
3
1. Blade Case
2. Hex bolt
3. Socket wrench
4. Blade guard
17
Download from Www.Somanuals.com. All Manuals Search And Download.
002216
Press the shaft lock to lock the spindle and use the socket
wrench to loosen the hex bolt clockwise. Then remove the
hex bolt, outer flange and blade.
2
1
3
5
4
1. Shaft lock
2. Arrow
3. Blade case
4. Socket wrench
5. Hex bolt
001771
To install the blade, mount it carefully onto the spindle, mak-
ing sure that the direction of the arrow on the surface of the
blade matches the direction of the arrow on the blade case.
Install the outer flange and hex bolt, and then use the socket
wrench to tighten the hex bolt (left-handed) securely counter-
clockwise while pressing the shaft lock.
2
3
1
4
5
Return the blade guard and center cover to its original posi-
tion. Then tighten the hex bolt clockwise to secure the center
cover. Release the handle from the raised position by pulling
the stopper pin. Lower the handle to make sure that the
blade guard moves properly. Make sure shaft lock has
released spindle before making cut.
1. Outer flange
2. Inner flange
3. Spindle
4. Saw blade
5. Hex bolt
001783
2
1
4
3
1. Arrow
2. Blade case
3. Saw blade
4. Arrow
18
Download from Www.Somanuals.com. All Manuals Search And Download.
002217
Dust bag
1
3
The use of the dust bag makes cutting operations clean and
dust collection easy. To attach the dust bag, fit it onto the
dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust bag of
its contents, tapping it lightly so as to remove particles adher-
ing to the insides which might hamper further collection.
2
1. Dust nozzle
2. Fastener
3. Dust bag
NOTE:
If you connect a Makita vacuum cleaner to your saw, more
efficient and cleaner operations can be performed.
Securing workpiece
WARNING:
•
•
It is extremely important to always secure the workpiece
properly and tightly with the vise. Failure to do so can
cause the tool to be damaged and/or the workpiece to
be destroyed. PERSONAL INJURY MAY ALSO
RESULT. Also, after a cutting operation, DO NOT raise
the blade until the blade has come to a complete stop.
001549
CAUTION:
1
2
When cutting long workpieces, use supports that are as
high as the top surface level of the turn base. Do not rely
solely on the vertical vise and/or horizontal vise to
secure the workpiece.
Thin material tends to sag. Support workpiece over its
entire length to avoid blade pinch and possible
KICKBACK.
1. Support
2. Turn base
19
Download from Www.Somanuals.com. All Manuals Search And Download.
001806
Vertical vise
6
7
1
2
3
The vertical vise can be installed in two positions on either
the left or right side of the guide fence or the holder assembly
(optional accessory). Insert the vise rod into the hole in the
guide fence or the holder assembly and tighten the screw to
secure the vise rod.
4
5
Position the vise arm according to the thickness and shape
of the workpiece and secure the vise arm by tightening the
screw. If the screw to secure the vise arm contacts the guide
fence, install the screw on the opposite side of vise arm.
Make sure that no part of the tool contacts the vise when
lowering the handle fully and pulling or pushing the carriage
all the way. If some part contacts the vise, re-position the
vise.
1. Vise arm
2. Vise rod
3. Guide fence
4. Holder
5. Holder assembly
6. Vise knob
7. Screw
Press the workpiece flat against the guide fence and the turn
base. Position the workpiece at the desired cutting position
and secure it firmly by tightening the vise knob.
CAUTION:
•
The workpiece must be secured firmly against the turn
base and guide fence with the vise during all operations.
001807
Horizontal vise (optional accessory)
3
2
1
The horizontal vise can be installed on the left side of the
base. By turning the vise knob counterclockwise, the screw
is released and the vise shaft can be moved rapidly in and
out. By turning the vise knob clockwise, the screw remains
secured. To grip the workpiece, turn the vise knob gently
clockwise until the projection reaches its topmost position,
then fasten securely. If the vise knob is forced in or pulled out
while being turned clockwise, the projection may stop at an
angle. In this case, turn the vise knob back counterclockwise
until the screw is released, before turning again gently clock-
wise.
4
1. Vise knob
2. Projection
3. Vise shaft
4. Base
The maximum width of the workpiece which can be secured
by the horizontal vise is 120 mm (4-3/4”).
CAUTION:
•
Grip the workpiece only when the projection is at the
topmost position. Failure to do so may result in
insufficient securing of the workpiece. This could cause
the workpiece to be thrown, cause damage to the blade
or cause the loss of control, which can result in
PERSONAL INJURY.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
002247
Holders and holder assembly
(optional accessories)
The holders and the holder assembly can be installed on
either side as a convenient means of supporting workpieces
horizontally. Install them as shown in the figure. Then tighten
the screws firmly to secure the holders and the holder
assembly.
1
2
1. Holder
2. Holder assembly
002246
When cutting long workpieces, use the holder-rod assembly
(optional accessory). It consists of two holder assemblies
and two rods 12.
2
CAUTION:
•
Always support long workpieces level with the top
surface of the turn base for accurate cuts and to prevent
dangerous loss of control of the tool.
1
1. Holder assembly
2. Rod 12
OPERATION
CAUTION:
•
•
•
Before use, be sure to release the handle from the
lowered position by pulling the stopper pin.
Make sure the blade is not contacting the workpiece, etc.
before the switch is turned on.
Do not apply excessive pressure on the handle when
cutting. Too much force may result in overload of the
motor and/or decreased cutting efficiency. Push down
handle with only as much force as is necessary for
smooth cutting and without significant decrease in blade
speed.
•
•
Gently press down the handle to perform the cut. If the
handle is pressed down with force or if lateral force is
applied, the blade will vibrate and leave a mark (saw
mark) in the workpiece and the precision of the cut will
be impaired.
During a slide cut, gently push the carriage toward the
guide fence without stopping. If the carriage movement
is stopped during the cut, a mark will be left in the
workpiece and the precision of the cut will be impaired.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
002248
1. Press cutting (cutting small workpieces)
Workpieces up to 50 mm (2”) high and 97 mm (3-13/16”)
wide can be cut in the following way.
Push the carriage toward the guide fence fully and
tighten the clamp screw on the turn base clockwise to
secure the carriage. Secure the workpiece with the vise.
Switch on the tool without the blade making any contact
and wait until the blade attains full speed before lower-
ing. Then gently lower the handle to the fully lowered
position to cut the workpiece. When the cut is com-
pleted, switch off the tool and WAIT UNTIL THE BLADE
HAS COME TO A COMPLETE STOP before returning
the blade to its fully elevated position.
CAUTION:
•
Firmly tighten the clamp screw on the turn base
clockwise so that the carriage will not move during
operation. Insufficient tightening may cause unexpected
kickback of the blade. Possible serious PERSONAL
INJURY may result.
002166
2. Slide (push) cutting (cutting wide workpieces)
Loosen the clamp screw on the turn base counterclock-
wise so that the carriage can slide freely. Secure the
workpiece with the vise. Pull the carriage toward you
fully. Switch on the tool without the blade making any
contact and wait until the blade attains full speed. Press
down the handle and PUSH THE CARRIAGE TOWARD
THE GUIDE FENCE AND THROUGH THE WORK-
PIECE. When the cut is completed, switch off the tool
and WAIT UNTIL THE BLADE HAS COME TO A COM-
PLETE STOP before returning the blade to its fully ele-
vated position.
CAUTION:
•
Whenever performing the slide cut, FIRST PULL THE
CARRIAGE TOWARD YOU FULLY and press down the
handle to the fully lowered position, then PUSH THE
CARRIAGE TOWARD THE GUIDE FENCE. NEVER
START THE CUT WITH THE CARRIAGE NOT FULLY
PULLED TOWARD YOU. If you perform the slide cut
without pulling the carriage fully or if you perform the
slide cut toward your direction, the blade may kickback
unexpectedly with the potential to cause serious
PERSONAL INJURY.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Never perform the slide cut with the handle locked in the
lowered position by pressing the stopper pin.
Never loosen the clamp screw which secures the
carriage while the blade is rotating. This may cause
serious injury.
3. Miter cutting
Refer to the previously covered “Adjusting the miter
angle”.
002249
4. Bevel cut
Loosen the lever and tilt the saw blade to set the bevel
angle (Refer to the previously covered “Adjusting the
bevel angle”). Be sure to retighten the lever firmly to
secure the selected bevel angle safely. Secure the work-
piece with a vise. Make sure the carriage is pulled all the
way back toward the operator. Switch on the tool without
the blade making any contact and wait until the blade
attains full speed. Then gently lower the handle to the
fully lowered position while applying pressure in parallel
with the blade and PUSH THE CARRIAGE TOWARD
THE GUIDE FENCE TO CUT THE WORKPIECE. When
the cut is completed, switch off the tool and WAIT UNTIL
THE BLADE HAS COME TO A COMPLETE STOP
before returning the blade to its fully elevated position.
CAUTION:
•
•
Always be sure that the blade will move down to bevel
direction during a bevel cut. Keep hands out of path of
saw blade.
During a bevel cut, it may create a condition whereby the
piece cut off will come to rest against the side of the
blade. If the blade is raised while the blade is still
rotating, this piece may be caught by the blade, causing
fragments to be scattered which is dangerous. The blade
should be raised ONLY after the blade has come to a
complete stop.
•
When pressing the handle down, apply pressure parallel
to the blade. If the pressure is not parallel to the blade
during a cut, the angle of the blade might be shifted and
the precision of the cut will be impaired.
5. Compound cutting
Compound cutting is the process in which a bevel angle
is made at the same time in which a miter angle is being
cut on a workpiece. Compound cutting can be performed
at angle shown in the table.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Miter angle
Left and Right 45˚
Right 50˚
Bevel angle
Left 0˚ - 45˚
Left 0˚ - 40˚
Left 0˚ - 30˚
Left 0˚ - 25˚
Right 55˚
Right 60˚
When performing compound cutting, refer to “Press cut-
ting”, “Slide cutting”, “Miter cutting” and “Bevel cut”
explanations.
6. Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
miter saw with the moldings laid flat on the turn base.
001555
There are two common types of crown moldings and one
type of cove moldings; 52/38° wall angle crown molding,
45° wall angle crown molding and 45° wall angle cove
molding. See illustrations.
52∞
38∞
45∞
45∞
45∞
45∞
1
2
3
1. 52/38° type crown molding
2. 45° type crown molding
3. 45° type cove molding
001556
There are crown and cove molding joints which are
made to fit “Inside” 90° corners ((1) and (2) in Fig. A) and
“Outside” 90° corners ((3) and (4) in Fig. A).
Measuring
Measure the wall length and adjust workpiece on table to
cut wall contact edge to desired length. Always make
sure that cut workpiece length at the back of the work-
piece is the same as wall length. Adjust cut length for
angle of cut. Always use several pieces for test cuts to
check the saw angles.
(1) (2) (3)(4)
1
2
Fig.A
1. Inside corner
2. Outside corner
001557
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw base
as indicated in the table (B).
1
(1)
(2)
(2)
(1)
(4)
(2)
(1)
(3)
2
(2)
(1)
(1)
(2)
Table (A)
Molding
Bevel angle
Miter angle
position in Fig. A 52/38˚ type 45˚ type 52/38˚ type 45˚ type
1. Inside corner
For inside
corner
For outside
corner
(1)
(2)
(3)
(4)
Right 31.6˚ Right 35.3˚
Left 31.6˚ Left 35.3˚
Right 31.6˚ Right 35.3˚
2. Outside corner
Left 33.9˚
Left 30˚
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Table (B)
Molding
Molding edge against
Finished piece
position in Fig. A guide fence
Ceiling contact edge should
Finished piece will
be on the Left side
of blade.
For inside
corner
(1)
be against guide fence.
Wall contact edge should be
against guide fence.
Ceiling contact edge should be be on the Right side
against guide fence. of blade.
(2)
(3)
Finished piece will
For outside
corner
(4)
Example:
In the case of cutting 52/38° type crown molding for
position (1) in Fig. A:
•
•
•
Tilt and secure bevel angle setting to 33.9°
LEFT.
Adjust and secure miter angle setting to 31.6°
RIGHT.
Lay crown molding with its broad back (hidden)
surface down on the turn base with its CEILING
CONTACT EDGE against the guide fence on
the saw.
•
The finished piece to be used will always be on
the LEFT side of the blade after the cut has
been made.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EN0002-1
000031
Compound Miter Saw
Miter and Bevel Angle Settings
Ceiling
52˚
38˚
Wall to Crown Molding Angle: 52/38 degrees
Wall Angle Bevel Angle Miter Angle
Wall Angle Bevel Angle Miter Angle
Wall Angle Bevel Angle Miter Angle
(deg.)
(deg.)
43.0
42.8
42.5
42.2
41.9
41.7
41.4
41.1
40.8
40.5
40.2
39.9
39.6
39.3
39.0
38.7
38.4
38.1
37.8
(deg.)
46.8
46.3
45.7
45.1
44.6
44.0
43.5
42.9
42.4
41.9
41.3
40.8
40.3
39.8
39.2
38.7
38.2
37.7
37.2
(deg.)
(deg.)
30.1
29.7
29.4
29.0
28.7
28.3
28.0
27.6
27.2
26.9
26.5
26.1
25.8
25.4
25.0
24.7
24.3
23.9
23.6
(deg.)
26.9
26.5
26.1
25.7
25.3
24.9
24.5
24.1
23.7
23.3
22.9
22.6
22.2
21.8
21.4
21.0
20.7
20.3
19.9
(deg.)
(deg.)
15.3
14.9
14.5
14.1
13.7
13.3
12.9
12.5
12.2
11.8
11.4
11.0
10.8
10.2
9.8
(deg.)
101
141
12.3
12.0
11.6
11.3
11.0
10.7
10.3
10.0
9.7
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
9.4
9.0
8.7
8.4
8.1
7.8
9.4
7.5
9.0
7.1
8.6
6.8
8.3
6.5
79
37.4
36.8
23.2
19.6
160
7.9
6.2
120
121
122
123
124
125
126
127
128
129
130
80
81
82
83
84
85
86
87
88
89
37.1
36.8
36.5
36.2
35.8
35.5
35.2
34.9
34.5
34.2
36.3
35.8
35.3
34.8
34.4
33.9
33.4
33.0
32.5
32.1
22.8
22.5
22.1
21.7
21.3
21.0
20.6
20.2
19.8
19.5
19.2
18.8
18.5
18.1
17.8
17.4
17.1
16.7
16.4
16.0
161
162
163
164
165
166
167
168
169
170
7.5
7.1
6.7
6.3
5.9
5.5
5.1
4.7
4.3
3.9
5.9
5.6
5.3
4.9
4.6
4.3
4.0
3.7
3.4
3.1
33.9
31.6
131
19.1
15.7
171
3.5
2.8
90
91
92
93
94
95
96
97
98
99
33.5
33.2
32.8
32.5
32.2
31.8
31.5
31.1
30.8
30.4
31.2
30.7
30.3
29.9
29.4
29.0
28.6
28.2
27.7
27.3
132
133
134
135
136
137
138
139
140
18.7
18.3
17.9
17.6
17.2
16.8
16.4
16.0
15.8
15.3
15.0
14.6
14.3
14.0
13.6
13.3
13.0
12.8
172
173
174
175
176
177
178
179
180
3.2
2.8
2.4
2.0
1.6
1.2
0.8
0.4
0.0
2.5
2.2
1.8
1.5
1.2
0.9
0.6
0.3
0.0
100
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EN0003-1
000032
Compound Miter Saw
Miter and Bevel Angle Settings
Ceiling
45˚
45˚
Wall to Crown Molding Angle: 45 degrees
Wall Angle Bevel Angle Miter Angle
Wall Angle Bevel Angle Miter Angle
Wall Angle Bevel Angle Miter Angle
(deg.)
(deg.)
37.8
37.5
37.3
37.1
36.8
36.6
36.4
36.1
35.9
35.6
35.4
35.1
34.9
34.6
34.4
34.1
33.9
33.6
33.3
(deg.)
50.8
50.2
49.6
49.1
48.5
48.0
47.4
46.9
46.4
45.8
45.3
44.8
44.2
43.7
43.2
42.7
42.1
41.6
41.1
(deg.)
(deg.)
26.7
26.4
26.1
25.8
25.5
25.2
24.9
24.6
24.2
23.9
23.6
23.3
23.0
22.7
22.3
22.0
21.7
21.4
21.0
(deg.)
30.2
29.8
29.4
28.9
28.5
28.1
27.6
27.2
26.8
26.3
25.9
25.5
25.1
24.7
24.3
23.8
23.4
23.0
22.6
(deg.)
(deg.)
13.7
13.3
13.0
12.6
12.3
11.9
11.6
11.2
10.9
10.5
10.2
9.8
(deg.)
101
141
14.1
13.7
13.3
12.9
12.6
12.2
11.8
11.5
11.1
10.7
10.4
10.0
9.6
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
9.5
9.2
9.3
8.8
8.9
8.5
8.5
8.1
8.2
7.8
7.8
7.4
7.5
79
33.1
40.6
20.7
22.2
160
7.1
7.1
120
121
122
123
124
125
126
127
128
129
130
80
81
82
83
84
85
86
87
88
89
32.8
32.5
32.3
32.0
31.7
31.4
31.1
30.9
30.6
30.3
40.1
39.6
39.1
38.6
38.1
37.7
37.2
36.7
36.2
35.7
20.4
20.0
19.7
19.4
19.1
18.7
18.4
18.1
17.7
17.4
21.8
21.4
21.0
20.6
20.2
19.8
19.4
19.0
18.6
18.2
161
162
163
164
165
166
167
168
169
170
6.7
6.4
6.0
5.6
5.3
4.9
4.6
4.2
3.9
3.5
6.7
6.4
6.0
5.7
5.3
5.0
4.6
4.3
3.9
3.5
30.0
35.3
131
17.1
17.9
171
3.2
3.2
90
91
92
93
94
95
96
97
98
99
29.7
29.4
29.1
28.8
28.5
28.2
27.9
27.6
27.3
27.0
34.8
34.3
33.9
33.4
32.9
32.5
32.0
31.6
31.1
30.7
132
133
134
135
136
137
138
139
140
16.7
16.4
16.0
15.7
15.4
15.0
14.7
14.3
14.0
17.5
17.1
16.7
16.3
15.9
15.6
15.2
14.8
14.4
172
173
174
175
176
177
178
179
180
2.8
2.5
2.1
1.8
1.4
1.1
0.7
0.4
0.0
2.8
2.5
2.1
1.8
1.4
1.1
7.0
0.4
0.0
100
27
Download from Www.Somanuals.com. All Manuals Search And Download.
001846
7. Cutting repetitive lengths
When cutting several pieces of stock to the same length,
ranging from 220 mm (8-5/8”) to 385 mm (15-1/8”), use
of the set plate (optional accessory) will facilitate more
efficient operation. Install the set plate on the holder
(optional accessory) as shown in the figure.
Align the cutting line on your workpiece with either the
left or right side of the groove in the kerf board, and while
holding the workpiece from moving, move the set plate
flush against the end of the workpiece. Then secure the
set plate with the screw. When the set plate is not used,
loosen the screw and turn the set plate out of the way.
1
2
3
1. Set plate
2. Holder
3. Screw
NOTE:
•
Use of the holder-rod assembly (optional accessory)
allows cutting repetitive lengths up to 2,200 mm (7.2 ft.)
approximately.
001563
8. Groove cutting
1
A dado type cut can be made by proceeding as follows:
Adjust the lower limit position of the blade using the
adjusting screw and the stopper arm to limit the cutting
depth of the blade. Refer to “Stopper arm” section
described on previously.
After adjusting the lower limit position of the blade, cut
parallel grooves across the width of the workpiece using
a slide (push) cut as shown in the figure. Then remove
the workpiece material between the grooves with a
chisel. Do not attempt to perform this type of cut using
wide (thick) blades or with a dado blade. Possible loss of
control and injury may result.
1. Cut grooves with blade
CAUTION:
•
Be sure to return the stopper arm to the original position
when performing other than groove cutting.
002193
Carrying tool
Make sure that the battery cartridge is removed. Secure the
blade at 0° bevel angle and the turn base at right miter angle
fully. Secure the slide poles after pulling the carriage toward
you fully. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
1
1. Stopper Pin
28
Download from Www.Somanuals.com. All Manuals Search And Download.
002221
Carry the tool by carrying grip as shown in the figure. If you
remove the holders, dust bag, etc., you can carry the tool
more easily.
CAUTION:
•
•
Always secure all moving portions before carrying the
tool.
Stopper pin is for carrying and storage purposes only
and not for any cutting operations.
MAINTENANCE
CAUTION:
•
•
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
WARNING:
Always be sure that the blade is sharp and clean for the
best and safest performance.
Adjusting the cutting angle
This tool is carefully adjusted and aligned at the factory, but
rough handling may have affected the alignment. If your tool
is not aligned properly, perform the following:
002242
1. Miter angle
1
2
Push the carriage toward the guide fence and tighten the
clamp screw on the turn base to secure the carriage.
Loosen the grip which secures the turn base. Turn the
turn base so that the pointer points to 0° on the miter
scale. Then turn the turn base slightly clockwise and
counterclockwise to seat the turn base in the 0° miter
notch. (Leave as it is if the pointer does not point to 0°.)
Loosen the hex bolts securing the guide fence using the
socket wrench.
1. Guide fence
2. Hex bolt
002209
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. Square the side of the
blade with the face of the guide fence using a triangular
rule, try-square, etc. Then securely tighten the hex bolts
on the guide fence in the order from the right side.
1
1. Triangular rule
29
Download from Www.Somanuals.com. All Manuals Search And Download.
002210
Make sure that the pointer points to 0° on the miter
scale. If the pointer does not point to 0°, loosen the
screw which secures the pointer and adjust the pointer
so that it will point to 0°.
1
2
3
1. Screw
2. Miter scale
3. Pointer
001818
2. Bevel angle
(1) 0° bevel angle
Push the carriage toward the guide fence and
tighten the clamp screw on the turn base to secure
the carriage. Lower the handle fully and lock it in the
lowered position by pushing in the stopper pin.
Loosen the lever at the rear of the tool.
1
4
3
2
Turn the 0° bevel angle adjusting bolt (lower bolt) on
the right side of the arm two or three revolutions
counterclockwise to tilt the blade to the right.
1. Sub arm
2. Arm
3. 0° bevel angle adjusting bolt
4. Lever
001819
Carefully square the side of the blade with the top
surface of the turn base using the triangular rule,
try-square, etc. by turning the 0° bevel angle adjust-
ing bolt clockwise. Then tighten the lever securely.
1
2
3
1. Triangular rule
2. Saw blade
3. Top surface of turn base
002211
Make sure that the pointer on the arm point to 0° on
the bevel scale on the arm holder. If it does not point
to 0°, loosen the screw which secures the pointer
and adjust the pointer so that it will point to 0°.
1
2
3
1. Screw
2. Pointer
3. Bevel scale
30
Download from Www.Somanuals.com. All Manuals Search And Download.
002250
(2) 45° bevel angle
Adjust the 45° bevel angle only after performing 0°
bevel angle adjustment. To adjust left 45° bevel
angle, loosen the lever and tilt the blade to the left
fully. Make sure that the pointer on the arm points to
45° on the bevel scale on the arm holder. If the
pointer does not point to 45°, turn the 45° bevel
angle adjusting bolt (upper bolt) on the right side of
the arm until the pointer points to 45°.
1
1. 45° bevel angle adjusting bolt
001145
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only iden-
tical carbon brushes.
1
1. Limit mark
002251
Use a screwdriver to remove the brush holder caps. Take out
the worn carbon brushes, insert the new ones and secure
the brush holder caps.
1
After replacing brushes, insert the battery cartridge into the
tool and break in brushes by running tool with no load for
about 1 minute. Then check the tool while running and elec-
tric brake operation when releasing the switch trigger. If elec-
tric brake is not working well, ask your local Makita service
center for repair.
2
1. Screwdriver
2. Brush holder cap
After use
•
After use, wipe off chips and dust adhering to the tool
with a cloth or the like. Keep the blade guard clean
according to the directions in the previously covered
section titled “Blade guard”. Lubricate the sliding
portions with machine oil to prevent rust.
•
When storing the tool, pull the carriage toward you fully
so that the slide pole is thoroughly inserted into the turn
base.
To maintain product SAFETY and RELIABILITY, repairs, any
other maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always using
Makita replacement parts.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
CAUTION:
•
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita service center.
•
Carbide-tipped saw blades
Miter saw blades
For smooth and precise cutting in various
materials.
•
•
•
•
•
•
•
•
•
•
•
Vise assembly (Horizontal vise)
Vertical vise
Socket wrench 10
Holder set
Holder assembly
Holder rod assembly
Set plate
Dust bag
Triangular rule
Lock-off button (2 pcs.)
Various type of Makita genuine batteries and chargers.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Stamp
Timbre
Makita Canada Inc.
1950 Forbes Street,
Whitby, Ontario
L1N 7B7
Fold
Download from Www.Somanuals.com. All Manuals Search And Download.
Your answers to the following questions are appreciated.
1.This product was purchased from?
3. How did you first learn of Makita Power Tools?
Hardware/lumber Store
Tool Distributor
Industrial Supply
Other (
Magazine/Newspaper
From dealer
Catalog
Other (
)
)
Store display
2. Use of the product is intended for?
4. Most favored points are?
Construction trade
Home maintenance
Other (
Design
Makita Brand
Power
Industrial maintenance
)
Features
Size
Other (
)
Price
5. Any comments?
Certificate of Warranty
Mail to Makita
Date Purchased
Model No.
Serial No.
Month
Day
Year 20
Male Female
Single
Married
Initial Last Name
Street Address
City
Province
Postal Code
Under 19
20-29
30-39
40-49
Over 50
AGE:
Occupation:
Dealer's Name & Address:
Download from Www.Somanuals.com. All Manuals Search And Download.
Paste Paste Paste Paste Paste Paste
Paste
Paste
Factory Service Centres
Head Office:
1950 Forbes St., Whitby, Ontario, L1N 7B7
(905) 571 - 2200 1-800-263-3734
Regional Office:
11771 Hammersmith Way, Richmond
B.C. V7A 5H6
(604) 272 - 3104 1-800-663-0909
Regional Office:
(Montreal)
6389 boul, Couture, St. Leonard, Quebec
H1P 3J5
(514) 323 - 1223 1-800-361-7049
Dartmouth:
202 Brownlow Avenue
Dartmouth, N.S., B3B 1T5
(902) 468 - 7064 1-888-625-4821
Ville St. Laurent:
(Montreal)
1140 Rue Bégin, Ville St. Laurent, Quebec
H4R 1X1
(514) 745 - 5025 1-888-745-5025
Les Saules:
(Quebec)
1200 St. Jean Baptiste, Unit 106, Les Saules,
Quebec, G2E 5E8
(418) 871 - 5720 1-800-663-5757
Nepean:
(Ottawa)
203 Colonnade Road, Unit #6, Nepean,
Ontario K2E 7K3
(613) 224 - 5022 1-888-560-2214
Whitby:
1950 Forbes St., Whitby, Ontario, L1N 7B7
(905) 571 - 2200 1-800-263-3734
London:
317 Adelaide St. S., Unit 117, London,
Ontario, N5Z 3L3
(519) 686 - 3115 1-800-571-0899
Mississauga:
Calgary:
6350 Tomken Rd., Unit 8, Mississauga,
Ontario, L5T 1Y3
(905) 670 - 7255 1-800-221-9811
#8-6115 Fourth St. S.E., Calgary
Alberta, T2H 2H9
(403) 243 - 3995 1-800-267-0445
Edmonton:
Richmond:
Coquitlam:
Winnipeg:
Saskatoon:
11614-149 Street, Edmonton, Alberta,
T5M 3R3
(780) 455 - 6644 1-888-455-6644
11771 Hammersmith Way, Richmond, B.C.,
V7A 5H6
(604) 272 - 3104 1-800-663-0909
2131 Hartley Ave., #103
Coquitlam, B.C. V3K 2Z3
(604) 525 - 7434 1-800-266-7738
1670 St. James Street, Winnipeg, Manitoba,
R3H 0L3
(204) 694 - 0402 1-800-550-5073
206A-2750 Faithful Avenue Saskatoon,
Saskatchewan, S7K 6M6
(306) 931 - 0111 1-888-931-0111
For the authorized service centre nearest you please refer to the local yellow pages directory under “tools” or con-
tact our customer service department (Tel) 1-800-263-3734
CUSTOMER RECORD
When you need service...
DATE
• Explain the problem in a letter
PURCHASED:
• Enclose the letter with the tool
DEALER’S NAME
• Package carefully and send prepaid
& ADDRESS:
to the nearest Makita factory or
authorized service centre
MODEL NO.:
SERIAL NO.:
35
Download from Www.Somanuals.com. All Manuals Search And Download.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from
workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during
this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres.
If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace)
without charge.
This Warranty does not apply:
• where normal maintenance is required,
• repairs have been made or attempted by others,
• the tool has been abused, misused or improperly maintained,
• alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM
THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS
WARRANTY.
“The Makita Warranty is the only and the entire written warranty given by Makita for the Makita tools. No dealer or his agent
or employee is authorized to extend or enlarge upon this warranty by any verbal or written statement or advertisement.”
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF
“MERCHANTABILITY” AND FITNESS FOR A SPECIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF THIS WARRANTY.
“This Warranty gives you specific rights. The provisions contained in this warranty are not intended to limit, modify, take away
from, disclaim or exclude any warranties set forth in any provincial legislation. To the extent required by law, the provisions in
any provincial or federal legislation with respect to warranties take precedence over the provisions in this warranty.”
Makita Corporation of America
2650 Buford Hwy., Buford, GA 30518
884306-230
Download from Www.Somanuals.com. All Manuals Search And Download.
|