Instruction Manual
Original Instruction Manual
DCS3410TH
Important:
Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety
regulations! Only persons who have completed training in working from elevated platforms (cherry pickers, lifts), from
platforms mounted on ladders or who are proficient in climbing with ropes are permitted to operate this chain saw.
Keep this Instruction Manual!
Download from Www.Somanuals.com. All Manuals Search And Download.
Delivery inventory
3
2
5
4
1
1. Chain saw
2. Guide bar
3. Saw chain
4. Chain protection cover
5. Assembly tool
6. Instruction manual (not shown)
In case one of the parts listed should not be included in the
delivery inventory, please consult your sales agent.
Symbols
You will notice the following symbols on the chain saw and in the instruction manual:
Read instruction manual
and follow the warning-
and safety precautions!
I/STOP-switch
(short-circuit switch)
Chaine brake
Fuel and oil mixture
Chain oil
Warning
This saw is to be used
by properly trained
operators only.
Stop engine!
Particular care
and caution!
Engine -manual start
Saw chain oil
adjustment screw
Forbidden!
Direction of chain
movement
Choke lever
Wear protective helmet,
eye and ear protection!
Carburetor adjustment
First aid
Wear protective
gloves!
Recycling
CAUTION: Kickback!
No smoking!
RE
Y
Hold the saw with both
hands while working!
One-handed use is ex-
CE-Marking
No open fire!
tremely hazardous!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
Power chain saws
CAUTION:
This power chain saw may be used only for sawing wood out of doors.
It is intended for the followung uses depending on its class:
This chain saw is designed especially for tree care and
surgery. All work with this chain saw is to be carried out
by properly trained persons only. Observe all literature,
procedures and recommendations from the relevant
professional organisation. Failure to do so constitutes a
high accident risk! We recommend always using a rising
platform (cherry picker, lift) for sawing in trees. Rappelling
techniques are extremely dangerous and require special
training! The operator must be trained in and familiar with
the use of safety equipment and working and climbing
techniques! Always use the appropriate belts, ropes and
carabiners when working in trees. Always use restraining
equipment for both the operator and the saw!
-
Professional and mid-class: Use on small, medium and large
trees: felling, limb removal, cutting to length, thinning.
-
Hobbyklasse:Occasionaluseonsmalltrees,fruit-treecare,felling,
limb removal, cutting to length.
Unauthorised users:
Persons who are not familiar with the Instruction Manual, children,
young people, and persons under the influence of drugs, alcohol or
medication must not use this saw.
General precautions
-
To ensure correct operation the user has to read this instruc-
tionmanualtomakehimselffamiliarwiththecharacteristicsofthe
chain saw. Users insufficiently informed will endanger themselves
as well as others due to improper handling.
-
-
Lend this chain saw only to persons with training and experience
in the use of tree-surgery saws. Always hand over the instruction
manual.
Children and young persons aged under 18 years must not be al-
lowed to operate the chain saw. Persons over the age of 16 years
may, however, use the chain saw for the purpose of being trained
as long as they are under the supervision of a qualified trainer.
-
-
Use chain saws always with the utmost care and attention.
Operate the chain saw only if you are in good physical condition. If
you are tired, your attention will be reduced. Be especially careful
at the end of a working day. Perform all work calmly and carefully.
The user has to accept liability for others.
1
-
-
Never work under the influence of alcohol, drugs or medication.
Afireextinguishermustbeavailableintheimmediatevicinitywhen
working in easily inflammable vegetation or when it has not rained
for a long time (danger of fire).
Protective equipment
-
In order to avoid head, eye, hand or foot injuries as well as
to protect your hearing the following protective equipment
must be used during operation of the chain saw:
-
The kind of clothing should be appropriate, i. e. it should be tight-
fitting but not be a hindrance. Do not wear jewellery or clothing
which could become entangled with bushes or shrubs. If you have
long hair, always wear a hairnet!
2
-
-
It is necessary to wear a protective helmet whenever working
with the chain saw. The protective helmet (1) is to be checked
in regular intervals for damage and is to be replaced after 5 years
at the latest. Use only approved protective helmets.
1
The face shield (2) of the protective helmet (or the goggles)
protects against sawdust and wood chips. During operation of the
chain saw always wear a goggle or a face shield to prevent eye
injuries.
3
-
-
Wear adequate noise protection equipment (ear muffs (3), ear
plugs, etc.). Octave brand analysis upon request.
Theprotectivejacket(4)consistsof22layersofnylonandprotects
theoperatoragainstcuts.Itisalwaystobewornwhenworkingfrom
elevated platforms (cherry pickers, lifts), from platforms mounted
on ladders or when climbing with ropes.
2
3
-
-
-
Theprotectivebraceandbiboverall(5)ismadeofanylonfabric
with 22 layers and protects against cuts. We strongly recommend
its use.
Protective gloves (6) made of thick leather are part of the pre-
scribed equipment and must always be worn during operation of
the chain saw.
4
7
During operation of the chain saw safety shoes or safety boots
(7)fittedwithantiskidsole, steeltoecapsandprotectionfortheleg
must always to be worn. Safety shoes equipped with a protective
layer provide protection against cuts and ensure a secure footing.
For working in trees the safety boots must be suitable for climbing
techniques.
5
6
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Fuels / Refuelling
-
-
-
-
Stop the engine before refuelling the chain saw.
Do not smoke or work near open fires (5).
Let the engine cool down before refuelling.
Fuels can contain substances similar to solvents. Eyes and skin
should not come in contact with mineral oil products. Always wear
protective gloves when refuelling. Frequently clean and change
protective clothes. Do not breathe in fuel vapors.
-
Donotspillfuelorchainoil.Whenyouhavespiltfueloroilimmediately
clean the chain saw. Fuel should not come in contact with clothes. If
your clothes have come in contact with fuel, change them ot once.
Ensure that no fuel or chain oil oozes into the soil (environmental
protection). Use an appropriate base.
-
-
5
6
7
Refuellingisnotallowedinclosedrooms.Fuelvaporswill accumulate
near the floor (explosion hazard).
-
-
Ensure to firmly tighten the screw caps of the fuel and oil tanks.
Change the place before starting the engine (at least 3 m from the
place of refuelling) (6).
Fuel cannot be stored for an unlimited period of time. Buy only as
much as will be consumed in the near future.
Use only approved and marked containers for the transport and
storage of fuel and chain oil. Ensure children have no access to fuel
or chain oil.
-
-
3 meters
Putting into operation
-
-
-
Do not work on your own. There must be someone around in
case of an emergency.
Ensure that there are no children or other people within the working
area. Pay attention to any animals in the working area, as well (7).
Before starting work the chain saw must be checked for
perfect function and operating safety according to the
prescriptions.
Checkespeciallythefunctionofthechainbrake, thecorrectmount-
ing of the guide bar, the correct sharpening and tightening of the
chain, the firm mounting of the sprocket guard, the easy motion
of the throttle lever and the function of the throttle lever lock, the
cleanliness and dryness of the handles, and the function of the
ON/OFF switch.
Put the chain saw only into operation if it is completely assembled.
Never use the chain saw when it is not completely assembled.
Before starting the chain saw ensure that you have a safe footing.
Putthechainsawintooperationonlyasdescribedinthisinstruction
manual (8). Other starting methods are not allowed.
When starting the chain saw it must be well supported and securely
held. The guide bar and chain must not be in contact with any
object.
Whenworkingwiththechainsawalwaysholditwithbothhands.
Take the back handle with the right hand and the tubular handle with
the left hand. Hold the handles tightly with your thumbs facing your
fingers. It is extremely dangerous to work with one hand, as the saw
can fall through the completed cut uncontrolled (high risk of injury).
Furthermore, it is impossible to control kickback with one hand.
CAUTION: When releasing the throttle lever the chain will keep
on running for a short period of time (free-wheeling).
Continuously ensure that you have a safe footing.
-
-
-
-
-
-
-
-
Hold the chain saw such that you will not breathe in the exhaust gas.
Do not work in closed rooms (danger of poisoning).
Switchoffthechainsawimmediatelyifyouobserveanychanges
in its operating behavior.
The engine must be switched off before checking the chain
tension, tightening the chain, replacing it or clearing mal-
functions (9).
8
-
-
-
-
-
-
When the sawing device is hit by stones, nails or other hard objects,
switch off the engine immediately and check the sawing device.
When stopping work or leaving theworking placeswitch off thechain
saw (9) and put it down such that nobody is endangered.
Do not put the overheated power chain saw in dry grass or on any
inflammable objects. The muffler is very hot (danger of fire).
CAUTION: Oil dropping from the chain or guide bar after having
stoppedthesawchainwillpollutethesoil.Alwaysuseanappropriate
base.
● Maintenance
● Refuelling
● Sharpening the chain
● Stopping work
● Transport
● Putting out of function
9
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Kickback
When working with the chain saw dangerous kickbacks may
-
occur.
-
Kickback occurs when the upper part of the end of the guide
bar inadvertently touches wood or other hard objects (10).
Before the saw chain enters the cut, it can slip to the side or
jump (caution: high risk of kickback).
-
-
This causes the saw to be thrown back toward the user with
great force and out of control. Risk of injury!
In order to prevent kickback, follow these rules:
Onlyspecially-trainedpersonsshouldperformplungecuts, i.e.,
piercing timber or wood with the tip of the saw!
Always observe the end of the guide bar. Be careful when
continuing an already started cut.
-
-
10
-
-
When starting to cut the chain must be running.
Ensurethatthechainisalwayssharpenedcorrectly.Payspecial
attention to the height of the depth limiter.
-
-
Never cut several branches at the same time. When cutting a
branch ensure that no other branch is touched.
When crosscutting a trunk be aware of the trunks next to it.
Working behavior/Method of working
-
Only use the chain saw during good light and visibility periods.
Be aware of slippery or wet areas, and of ice and snow (risk of
slipping). The risk of slipping is extremely high when working
on recently peeled wood (bark).
11
-
Never work on unstable surfaces. Make sure that there are no
obstacles in the working area, risk of stumbling.Always ensure
that you have a safe footing.
-
-
-
Never saw above your shoulder height (11).
Never saw while standing on a ladder (11).
Never climb a tree and work without the appropriate restraining
systems for the operator and the saw. We recommend always
working from a rising platform (cherry picker, lift).
Do not work leaning too far over.
-
-
Guide the chain saw in such a way that no part of your body is
within the elongated swivelling range of the saw (12).
Use the chain saw for sawing wood only.
-
-
Avoid touching the ground with the chain saw while it is still
running.
12
13
14
-
-
Never use the chain saw for lifting up or removing pieces of
wood or other objects.
Remove foreign objects such as sand, stones and nails found
within the working area. Foreign objects may damage the saw-
ing device and can cause dangerous kickback.
When sawing precut timber use a safe support (sawing jack,
13). Do not steady the workpiece with your foot, and do not
allow anyone else to hold or steady it.
Z
-
-
-
Secure round pieces against rotation.
For felling and crosscuts the spike bar (13, Z) must be ap-
plied to the wood to be cut. We also recommend using the
spike bar when cutting off thick branches.
-
Before performing a crosscut firmly apply the spike bar to the
timber, only then can the timber be cut with the chain running.
For this the chain saw is lifted at the back handle and guided
with the tubular handle. The spike bar serves as a centre of
rotation. Continue by slightly pressing down the tubular handle
and simultaneously pulling back the chain saw.Apply the spike
bar a little bit deeper and once again lift the back handle.
When the timber must be pierced for cutting or longitudi-
nal cuts are to be performed it is urgently recommended
to have this carried out by specially trained persons only
(high risk of kickback).
-
-
Do longitudinal - lengthwise - cuts at the lowest possible
angle (14). Be very careful when doing this type of cut, as the
spike bar cannot grip.
-
The saw must be running whenever you remove the chain saw
from the wood.
-
Whenperformingseveralcutsthethrottlelevermustbereleased
in between.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
-
-
Be careful when cutting splintery wood. Cut pieces of wood
may be pulled along (risk of injuries).
When cutting with the upper edge of the guide bar, the chain
saw may be pushed in the direction of the user if the chain
gets clamped. For this reason use the lower edge of the bar
whenever possible. The chain saw will then be pushed away
from you (15).
-
If the timber is under tension (16), first cut the pressure side
(A). Then the crosscut can be performed on the tension side
(B). Thus clamping of the guide bar can be avoided.
15
CAUTION:
Peoplefellingtreesorcuttingofbranchesmustbespecially
trained. High risk of injuries!
-
-
When cutting of branches, the chain saw should be supported
on the trunk. Do not use the end of the bar for cutting (risk of
kickback).
B
A
B
Be aware of branches under tension. Do not cut free branches
from below.
-
-
Never perform detensioning cuts while standing on the trunk.
Before cutting down a tree ensure that
a) only those people are within the working area which are
actually involved in cutting down the tree.
16
b) every worker involved can withdraw without stumbling (the
people should withdraw backwards in a diagonal line, i. e.
at a degree of 45°).
c) the bottom part of the trunk is free from foreign objects,
underbrush and branches. Make sure to have a safe footing
(risk of stumbling).
45°
d) the next working place is at least 2 1/2 tree lengths away
(17). Before cutting down the tree check the direction of fall
and make sure that there are neither people nor objects
within a distance of 2 1/2 tree lengths.
2 1/2
-
Judging the tree:
45°
Direction of hanging - loose or dry branches - height of the tree
- natural overhang - is the tree rotten?
= cutting down area
-
Take into account the direction and speed of the wind. If strong
gusts are occurring, do not do any felling. Avoid sawdust (pay
attention to the direction the wind is blowing)!
17
-
Cutting the roots:
Start with the strongest root. First do the vertical and then the
horizontal cut.
-
Notching the trunk (18, A):
The notch determines the direction of fall and guides the tree.
The trunk is notched perpendicular to the direction of fall and
penetrates 1/3 -1/5 of the trunk diameter. Perform the cut near
the ground.
-
When correcting the cut, always do so over the whole width of
the notch.
-
-
-
Cut down the tree (19, B) above the bottom edge of the notch
(D). The cut must be exactly horizontal. The distance between
both cuts must be approx. 1/10 of the trunk diameter.
18
The material between both cuts (C) serves as a hinge. Never
cut it through, otherwise the tree will fall without any control.
Insert felling wedges in time.
Secure the cut only with wedges made of plastic or aluminium.
Do not use iron wedges. If the saw hits an iron wedge the chain
can be seriously damaged or torn.
-
-
-
When cutting down a tree always stay sidewards of the falling
tree.
When withdrawing after having performed the cut, be alert for
falling branches.
When working on sloping ground the user of the chain saw
must stay above or sidewards of the trunk to be cut or the tree
already cut down.
19
-
Be alert for trunks which may roll towards you.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Transport and storage
-
When changing your location during work switch off the chain
saw and actuate the chain brake in order to prevent an inadvert-
ent start of the chain.
-
-
Never carry or transport the chain saw with the chain running.
When transporting the chain saw over long distances the guide
bar protection cover (delivered with the chain saw) must be
applied.
-
Carry the chain saw with the tubular handle. The guide bar
points backwards (20). Avoid coming in contact with the muffler
(danger of burns).
20
-
-
-
Ensuresafepositioningofthechainsawduringcartransportation
to avoid fuel or chain oil leakage.
Store the chain saw safely in a dry place. It must not be stored
outdoors. Keep the chain saw away from children.
Before storing the chain saw over a long period of time or ship-
ping it the fuel and oil tanks must be completely emptied.
Maintenance
-
Before performing maintenance work switch off the chain
saw (21) and pull out the plug cap.
-
Before starting work always check the operating safety of the
chain saw, in particular the function of the chain brake. Make
sure the saw chain is properly sharpened and tensioned (22).
21
-
Operate the chain saw only at a low noise and emission level.
For this ensure the carburetor is adjusted correctly.
-
-
Regularly clean the chain saw.
Regularly check the tank cap for tightness.
Observetheaccidentpreventioninstructionsissuedbytrade
associationsandinsurancecompanies.Donotperformany
modifications on the chain saw. You will put your safety at
risk.
Perform only the maintenance and repair works described in
the instruction manual. All other work must be carried out by
MAKITA Service.
Use only original MAKITA spare parts and accessories.
22
Using spare parts other than original MAKITA parts or acceso-
ries and guide bar/chain combinations or lengths which are not
approved bring a high risk of accidents. We cannot accept any
responsibility for accidents and damage resulting from using
sawing devices or accesories which have not been approved.
First aid
For the event of a possible accident, please make sure that a
firstaidkitisalwaysimmediatelyavailablecloseby.Immediately
replace any items used from the first aid box.
When calling for help, give the following information:
- Place of the accident
SERVICE
- What happened
23
- Number of injured people
- Kind of injuries
- Your name!
NOTE
Individuals with poor circulation who are exposed to excessive
vibration may experience injury to blood vessels or the nervous
system.
Vibration may cause the following symptoms to occur in the fingers,
handsorwrists:”Fallingasleep”(numbness),tingling,pain,stabbing
sensation, alteration of skin colour or of the skin. If any of these
symptoms occur, see a physician!
24
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
DCS3410TH
Stroke volume
cm3
34
38
Bore
mm
Stroke
mm
30
Max. power at operating speed
Max. torque at speed
kW / rpm
Nm / rpm
rpm
1,4 / 8.500
1,6 / 6.500
3.000 / 12.500
4.500
Idling speed / max. engine speed with bar and chain
Coupling speed
rpm
Sound pressure level at the workplace LpA, eq per ISO/CD 22868 1) 3) dB (A)
94,1 / KpA = 2,5
102,9 / KWA = 2,5
Sound power level LWA, eq per ISO/CD 22868 1) 3)
Vibration acceleration ahv, eq per ISO 22867 1) 3)
- Tubular handle
dB (A)
m/s2
m/s2
Type
Type
Type
mm
kg/h
g/kWh
l
4,7 / K = 2,0
5,2 / K = 2,0
WALBRO WT-778
electronic
NGK BPMR 7A
0,5
- Rear handle
Carburetor (diaphragm carburetor)
Ignition system
Spark plug
Electrode gap
Fuel consumption at max. load per ISO 7293
Specific consumption at max. load per ISO 7293
Fuel tank capacity
0,65
463
0,28
Chain oil tank capacity
I
0,22
Mix ratio (fuel/two-stroke oil)
- when using MAKITA oil
50 : 1
- when using Aspen Alkylat (two-stroke fuel)
- when using other oils
50 : 1 (2%)
50 : 1 (quality grade: JASO FC or ISO EGD)
Chain brake
Chain speed 2)
Actuation manually or by kickback
21
m/s
inch
Z
Sprocket pitch
3/8 / 1/4
Number of teeth
6
/
8
Chain type - see the Extract from the spare-parts list
Pitch / Driving element strength
Guide bar, length of a cut
inch
cm
3/8 / .050
1/4 / .050
30 / 35
3,3
Guide bar type - see the Extract from the spare-parts list
Weight (fuel tank empty, without chain and guide bar)
kg
1) Figures derived in equal part from idle, full-load, and top-speed operation.
2) At 1.33 times rated speed. 3) Uncertainty (K=).
1
2
3
4
5
6
7
Denomination of components
1
2
3
4
5
6
7
8
9
Rear handle
Safety locking button (throttle lock)
Throttle lever
Hand guard (release for chain brake)
Spike bar (accessories)
Chain
15
14
13
9
8
Guide bar
Chain protection cover
Retaining nuts
10 Chain catch (safety device)
11 Sprocket guard
12 11 10
12 Muffler
16
17
18
13 Spark plug
14 Serial number
15 Adjusting screw for oil pump
16 Front grip (tubular handle)
17 Starter grip
26
25
18 I/STOP-switch (short-circuit switch)
19 Carabiner or rope attachment point
20 Oil tank cap
24
21 Fan housing with starting assembly
22 Fuel tank cap
23
23 Air filter cover
24 Choke switch
19
25 Adjusting screws for carburetor
26 Fuel pump (Primer)
22 21
20
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PUTTING INTO OPERATION
CAUTION:
Before doing any work on the guide bar or chain, always
switch off the engine and pull the plug cap off the spark
plug (see „Replacing the spark plug“). Always wear pro-
tective gloves!
CAUTION:
Donotstartthesawuntilithasbeencompletelyassembled
and inspected!
A
Mounting the guide bar and saw chain
Use the universal wrench delivered with the chain saw for the
following work.
Put the chain saw on a stable surface and carry out the following
steps for mounting the guide bar and chain:
1
2
Disengage the chain brake by pulling the hand guard (1) in the
direction of the arrow.
Unscrew retaining nuts (2).
Carefully spread the sprocket guard (3), pull it from its fixture
(4) and remove it.
4
3
B
Turn the chain adjusting screw (5) to the left (counterclockwise)
until the pin (6) is at the left stop.
6
5
C
Position the guide bar (7). Make sure that the pin (8) of the chain
tightener is in the hole on the guide bar.
7
8
D
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Lift the chain (9) over the sprocket (10). Using your right hand,
guide the chain into the top guide groove (11) on the guide
bar.
Note that the cutting edges along the top of the chain must
point in the direction of the arrow!
9
10
11
E
9
12
Pull the chain (9) around the sprocket nose (12) of the guide
bar in the direction of the arrow.
F
First, push the sprocket guard (3) into its fixture (B/4), then push
it over the retaining bolts while lifting the saw chain (9) over the
chain catch (13).
3
Manually tighten the retaining nuts (2).
13
9
2
G
2
Tightening the saw chain
Turn the chain tightener (C/5) to the right (clockwise)
until the chain engages the guide groove of the bottom side of
the bar (see circle).
Slightly lift the end of the guide bar and turn the chain adjusting
screw (C/6) to the right (clockwise) until the chain rests against
the bottom side of the guide bar.
Whilestillholdingupthetipoftheguidebar, tightentheretaining
nuts (2) with the universal wrench.
H
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the chain tension
The tension of the chain is correct if the chain rests against
the bottom side of the guide bar and can still be easily turned
by hand.
While doing so the chain brake must be released.
Check the chain tension frequently - new chains tend to get
longer during use!
When checking the chain tension the engine must be switched
off.
NOTE:
It is recommended to use 2-3 chains alternatively.
In order to guarantee uniform wear of the guide bar the bar
should be turned over whenever replacing the chain.
A
Chain brake
The DCS3410 comes with an inertia chain brake as standard
equipment. If kickback occurs due to contact of the guide-bar tip
with wood (see SAFETY PRECAUTIONS, page 6), the chain
brake will stop the chain through inertia if the kickback is suf-
ficiently strong.
The chain will stop within a fraction of a second.
Thechainbrakeisinstalledtoblockthesawchainbeforestart-
ing it and to stop it immediately in case of an emergency.
IMPORTANT: NEVER run the saw with the chain brake acti-
vated (except for testing, see “Testing chain brake”)! Doing so
can very quickly cause extensive engine damage!
ALWAYS release the chain brake before
starting the work!
NOTE:
The chain brake is a very important safety device and like
any other component subject to normal wear and tear.
Regular inspection and maintenance are important for your
own safety and must be done by a MAKITA service centre.
SERVICE
B
Engaging the chain brake (braking)
2
1
If the kickback is strong enough the sudden acceleration of
the guide bar combined with the inertia of the hand guard (1)
will automatically actuate the chain brake.
1
To engage the chain brake manually, simply push the hand
guard (1) forward (towards the tip of the saw) with your left
hand (arrow 1).
Releasing the chain brake
Pull the hand guard (1) towards you (arrow 2) until you feel it
catch. The brake is now released.
C
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Fuel
CAUTION:
This saw is powered by mineral-oil products (gasoline and
oil).
Be especially careful when handling gasoline .
Donotsmoke.Keeptoolwellawayfromopenflames,spark,
or fire (explosion hazard).
Gasoline
50:1
50:1
Fuel mixture
OIL
Thistoolispoweredbyahigh-performanceair-cooledtwo-stroke
engine. It runs on a mixture of gasoline and two-stroke engine
oil.
+
The engine is designed for unleaded regular gasoline with a
min. octane value of 91 ROZ. In case no such fuel is available,
you can use fuel with a higher octane value. This will not affect
the engine.
1000 cm3
5000 cm3 (5 litres)
10000 cm3 (10 litres)
(1 litre)
20 cm3
100 cm3
200 cm3
20 cm3
100 cm3
200 cm3
In order to obtain an optimum engine output and to protect
your health and the environment use unleaded fuel only.
Thoroughly shake the mixture before filling it into the
chain saw tank.
To lubricate the engine, use a synthetic oil for two-stroke air-
cooled engines (quality grade JASO FC or ISO EGD), which
has to be added to the fuel. The engine has been designed for
use of MAKITA high-performance two-stroke engine oil and a
mixture ratio of only 50:1 to protect the environment. In addi-
tion, a long service life and reliable operation with a minimum
emission of exhaust gases are ensured.
It is not wise to add more engine oil than specified
to ensure safe operation. This will only result in a
higher production of combus-tion residues which
will pollute the environment and clog the exhaust
channel in the cylinder as well as the muffler. In
addition, fuel consumption will rise and perform-
ance will decrease.
MAKITA high-performance two-stroke engine oil is available in
the following sizes to suit your individual requirements:
The Storage of Fuel
Fuelshavealimitedstoragelife. Fuelandfuelmixtures
age through evaporation, especially at high tempera-
tures. Aged fuel and fuel mixtures can cause starting
problems and damage the engine.Purchase only that
amount of fuel, which will be consumed over the next
few months. At high temperatures, once fuel has been
mixed it should be used up in 6-8 weeks.
1
l
order number 980 008 607
order number 980 008 606
100 ml
In case MAKITA high-performance two-stroke engine oil is not
available, it is urgently recommended to use a mixture ratio of
50:1 with other two-stroke engine oils, as otherwise optimum
operation of the engine cannot be guaranteed.
Store fuel only in proper containers, in dry, cool,
secure locations!
Caution: Do not use ready-mixed fuel from petrol
stations.
AVOID SKIN AND EYE CONTACT
The correct mixture ratio:
Mineral oil products degrease your skin. If your skin
comes in contact with these substances repeatedly
and for an extended period of time, it will desiccate.
Various skin deseases may result. In addition, allergic
reactions are known to occur.
50:1 whenusingMAKITAhigh-performancetwo-strokeengine
oil, i. e. mix 50 parts gasoline with 1 part oil.
50:1 when using other synthetic two-stroke engine oils
(quality grade JASO FC or ISO EGD), i. e. mix 50 parts
gasoline with 1 part oil.
Eyescanbeirritatedbycontactwithoil.Ifoilcomesinto
your eyes, immediately wash them with clear water.
NOTE:
For preparing the fuel-oil mixture first mix the entire oil quan-
tity with half of the fuel required, then add the remaining fuel.
If your eyes are still irritated, see a doctor immedi-
ately!
D
Chain oil
Use an oil with adhesive additive for lubricating the chain and
guide bar. The adhesive additive prevents the oil from being
flung off the chain too quickly.
BIOTOP chain oil is available in the following sizes:
We recommend the use of chain oil which is bio-degradable in
order to protect the environment. The use of bio-degradable oil
may even be required by local regulations.
1 l order number 980 008 610
5 l order number 980 008 611
The chain oil BIOTOP sold by MAKITA is made of special
vegetable oils and is 100% bio-degradable. BIOTOP has been
granted the „blue angel“ (Blauer Umweltschutz-Engel) for being
particularly environment-friendly (RAL UZ 48).
Bio-degradable oil is stable only for a limited period of
time. It should be used within 2 years from the date of
manufacture (printed on the container).
E
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Important note on bio-degradable chain oils:
If you are not planning to use the saw again for an ex-
tended period of time, empty the oil tank and put in a
small amount of regular engine oil (SAE 30), and then
run the saw for a time. This is necessary to flush out all
remaining bio-degradable oil from the oil tank, oil-feed
system, chain and guide bar, as many such oils tend to
leave sticky residues over time, which can cause damage
to the oil pump or other parts.
The next time you use the saw, fill the tank with BIOTOP
chain oil again. In case of damage caused by using waste
oil or unappropriate chain oil the product guarantee will
be null and void.
Your salesman will inform you about the use of chain
oil.
NEVER USE WASTE OIL
Waste oil is very dangerous for the environment.
Waste oil contains high amounts of carcinogenic substances.
Residues in waste oil result in a high degree of wear and tear
at the oil pump and the sawing device.
waste oil
In case of damage caused by using waste oil or unappropriate
chain oil the product guarantee will be null and void.
Your salesman will inform you about the use of chain oil.
AVOID SKIN AND EYE CONTACT
Mineral oil products degrease your skin. If your skin comes in
contact with these substances repeatedly and for an extended
periodoftime,itwilldesiccate.Variousskindeseasesmayresult.
In addition, allergic reactions are known to occur.
Eyes can be irritated by contact with oil. If oil comes into your
eyes, immediately wash them with clear water.
If your eyes are still irritated, see a doctor immediately!
A
Refuelling
FOLLOW THE SAFETY PRECAUTIONS!
Be careful and cautious when handling fuels.
The engine must be switched off!
Thoroughly clean the area around the caps, to prevent dirt from
getting into the fuel or oil tank.
Unscrew the cap and fill the tank with fuel (fuel/oil mixture) or
chain oil as the case may be. Fill up to the bottom edge of the
filler neck. Be careful not to spill fuel or chain oil!
Tighten the tank cap as far as it will go.
After refuelling, clean the tank cap and surroundings and
make sure the cap is sealed!
Lubricating the chain
fuel/oil mixture
chain oil
During operation there must always be sufficient chain oil in
the chain-oil tank to provide good chain lubrication. One filling
is sufficient for about one half-hour of continuous operation.
When working, check that there is still sufficient chain oil in the
tank and top up if necessary. Check only when the engine
is switched off!
B
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the chain lubrication
The engine must be switched off.
You can adjust the oil pump feed rate with the adjusting screw
(1). The amount of oil can be adjusted using the universal
wrench.
Recommended settings:
- 25 cm guide bar
- 30 cm guide bar
- 35 cm guide bar
- 40 cm guide bar
1
C
To ensure troublefree operation of the oil pump the oil guide
groove at the crank case (2) and the oil inlet bore in the guide
bar (3) must be cleaned regularly.
2
3
D
Checking the chain lubrication
Never work with the chain saw withoute sufficient chain lubrica-
tion. Otherwise the service life of the chain and guide bar will
be reduced.
Before starting work check the oil level in the tank and the oil
feed.
Check the oil feed rate as described below:
Start the chain saw (see ”Starting the engine”).
Hold the running chain saw approx. 15 cm above a trunk or
the ground (use an appropriate base).
If the lubrication is sufficient, you will see a light oil trace be-
cause oil will be flung off the sawing device. Pay attention to the
direction the wind is blowing and avoid unnecessary exposure
to the oil spray!
Note:
After the saw has been turned off it is normal for residual chain
oil to drip from the oil feed system, the guide bar and the chain
for a time. This does not constitute a defect!
Place the saw on a suitable surface.
E
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the engine
Donotstartthesawuntilithasbeencompletelyassembled
and inspected!
Move at least 3m away from the place where you fuelled the
saw.
Make sure you have a good footing, and place the saw on the
ground in such a way that the chain is not touching anything.
Engage the chain brake (lock).
Grasp the rear handle firmly in one hand and hold the saw
firmly against the ground. Press with one knee on the rear
handle.
A
IMPORTANT: The choke switch (5) is coupled to the throttle lever (1). It will revert to its original position automatically once
the throttle lever has been pressed.
If the throttle lever is pressed before the engine starts, then the choke switch (5) will have to be reset to the appropriate
position.
Cold start:
Prime the fuel pump (6) by pressing it several times until you
can see fuel in the pump.
2
1
Move the short-circuit switch (3) forward in the direction of the
arrow.
Turn the choke lever (5) up (see “Cold start” illustration). This
simultaneously actuates the half-throttle lock.
3
Slowly pull out the starter cable (4) until you notice resistance
(the piston is positioned before the top dead centre).
6
Nowpullthestartercablewithafastandforcefulmovement
until you hear the first ignition.
CAUTION:Donotpulloutthestartercablemorethanapprox.50
cm, and lead it back by hand. For efficient starting, it is important
to pull the starter cable quickly and powerfully.
Turn the choke lever (5) down (see “Warm start” illustration)
and pull the starter cable again. As soon as the engine is
running, grasp the rear handle (this actuates the grip safety (2))
and tap the throttle (1). This will release the half-throttle lock
and the engine will run in idle.
4
Caution: The engine is to be run at idling speed immediately
after starting or damage may occur to the chain brake.
Now release the chain brake.
5
5
Warm start:
As for cold start, except before pulling the starter cable, turn
the choke lever (5) briefly to the “Cold start” position and
then immediately back to “Warm start” (this activates the
half-throttle lock).
Cold start
Warm starting
Important: If the fuel tank has been completely emptied and the
enginehasstoppedduetolackoffuelprimethefuelpump(6)by
pressing it several times until you can see fuel in the pump.
Stopping the engine
Put the short-circuiting switch (3) in position „STOP“.
B
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the chain brake
Do not work with the chain saw without first checking the
chain brake!
Start the engine as described (make sure you have a good
footing, and place the chain saw on the ground in such a way
that the guide bar is free of contact).
Grasp the tubular handle firmly with one hand and hold the grip
with the other.
7
With the engine running at moderate speed, press the hand
guard (7) in the direction of the arrow with the back of your
hand until the chain brake engages. The chain should stop
immediately.
Immediately release the throttle and release the chain brake.
IMPORTANT: If the chain does not stop immediately in this
test, do not under any circumstances proceed with work.
Contact a MAKITA service center.
C
Adjusting the carburetor
(only for EU-countries)
9
CAUTION:
Do not adjust the carburetor until the machine has been
completely assembled and checked! Do not adjust the
carburetor without a tachometer!
8
Carburetor adjustment is necessary for optimum engine
performance, for safer and more economical operation.
Adjust the carburetor only with the engine warm, a clean
air filter, and properly installed cutting tool.
Carburetor adjustment may be done only by a MAKITA
service centre. Improper adjustment can cause damage
to the engine.
In order to comply with new emissions legislation, limits have
been placed on the carburetor adjusting screws (H) and (L).
2. Set idle
This limitation (to about 180 degrees) prevents an exces-
sively rich mixture. This in turn ensures compliance with
emissions rules as well as optimum engine performance and
economical fuel consumption.
Set the idle speed per the technical specifications.
Turning the adjusting screw (S) in (clockwise) increases the
idle speed. Turning it out (counter-clockwise) lowers the idle
speed. The cutting tool must not rotate!
You will need a tachometer (8, part No. 950 233 210) for
optimum adjustment. Exceeding the maximum permissible
speed can lead to overheating and under-lubricating, and
damage to the engine!
3. Check acceleration
When the throttle is pressed, the engine should go smoothly
from idle to high speed.
Factory setting of adjusting screws (H) and (L): Turned out
almost all the way (counterclockwise).
Turn adjusting screw (L) out (counterclockwise) in small
increments until acceleration is good.
Use a screwdriver (9, blade width 4 mm, part No. 944 340 001)
to adjust the screws.
For proper adjustment, proceed as follows:
4. Set maximum permissible speed
Checking adjusting screw (H)
Set the maximum speed by minimal adjustments of the adju-
stingscrew(H)inaccordancewiththetechnicalspecifications.
Turning the adjusting screw (H) clockwise increases the
speed. Never exceed the maximum permissible speed!
Before starting the engine make sure that adjusting screw (H) is
turned out counterclockwise until it reaches a noticeable stop.
The limitations do not prevent excessively lean (under-lu-
bricated) running!
1. Start engine and let it warm up (3-5 minutes)
2. Set idle
5. Check idle speed
Check the idle speed after setting the top speed (the cutting
tool must not rotate!).
3. Check acceleration
4. Set maximum permissible speed
5. Check idle speed
Repeat the adjustment procedure starting at Step 2, until the
engine runs with the correct idle speed, good acceleration,
and maximum permissible speed.
D
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the carburetor
(only for not EU-countries)
9
Carburetor adjustment is necessary for optimum engine
performance, for safer and more economical operation. The
engine should be warm, the air filter clean, and the chain
properly tensioned. Have carburetor adjustment done by
an authorised MAKITA service centre.
8
The carburetor is factory-adjusted for the air pressure at sea
level. At other elevations or under other conditions of weather,
temperature, or humidity, or when breaking in a new engine,
it may be necessary to make slight adjustments to the carbu-
retor.
You will need a tachometer (E/8) (part No. 950 233 210) for
optimum adjustment. Exceeding the maximum permissible
speed can lead to overheating and under-lubricating, and
damage to the engine!
3. Check acceleration
If not using a tachometer, do not go below the specified
basic setting of the main nozzle (H). Doing so may cause
engine damage due to overheating and insufficient lubri-
cation!
When the throttle is pressed, the engine should go smoothly
from idle to high speed.
If this is too slow, turn the adjusting screw (L) in small (max.
1/8 turns) increments counter-clockwise.
Adjust the carburetor using a 4 mm screwdriver. The screw-
driver shown (E/9) (part No. 944 340 001) has a molded-on
lug to assist in adjustment.
4. Set maximum permissible speed
Set the maximum speed by minimal adjustments of the
adjusting screw (H) in accordance with the technical
specifications. Turning the adjusting screw (H) clockwise
increases the speed, turning it counter-clockwise reduces
the speed.
Before undertaking the adjustment, run the engine for 3-5 mi-
nutes to warm it up, but not at high speed!
For proper adjustment, proceed as follows:
1. Basic setting (engine off)
Start engine and let it warm up.
2. Set idle
5. Check idle speed
Check the idle speed after setting the top speed (the chain
must not move).
3. Check acceleration
Repeat the adjustment procedure starting at Step 2, until
the engine runs with the correct idle speed, good accele-
ration, and maximum permissible speed.
4. Set maximum permissible speed
5. Check idle speed
Repeat steps 2-5 until you get the right idle speed, good acce-
leration and maximum permissible speed.
1. Basic setting
Carefully turn the adjusting screws for the main nozzle (H)
and idle nozzle (L) clockwise until you feel a stop.
Turn adjusting screws (H) and (L) 11/4 turn counter-clockwise.
2. Set idle
Set the idle speed per the technical specifications.
Turning the adjusting screw (S) in (clockwise) increases the idle
speed. Turning it out (counter-clockwise) lowers the idle speed.
In no case should the chain move.
E
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Sharpening the saw chain
CAUTION:Beforedoinganyworkontheguidebarorchain,
always switch off the engine and pull the plug cap off the
spark plug (see „Replacing the spark plug“). Always wear
protective gloves!
The chain needs sharpening when:
The sawdust produced when sawing damp wood looks like
wood flour.
The chain penetrates the wood only under great pressure.
The cutting edge is visibly damaged.
The saw is pulled to the left or right when sawing. This is caused
by uneven sharpening of the chain.
Important: Sharpen frequently, but without removing too
much metal!
Generally, 2 or 3 strokes of the file will be enough.
Have the chain resharpened at a service centre when you have
already sharpened it yourself several times.
A
Proper sharpening:
CAUTION: Use only chains and guide bars designed for
this saw (see the Extract from the spare-parts list)!
0,64 mm
(.025”)
0,64 mm
(.025”)
All cutters must be of the same length (dimension a). Cutters
with different lengths result in rough running of the chain and
can cause cracks in the chain.
Minimumcutterlengthis3mm.Donotresharpenthechainwhen
the minimum cutter length has been reached; at this point, the
chain must be replaced (see the Extract from the spare-parts
list and „Replacing the chain“).
The depth of the cut is determined by the difference in height
between the depth limiter (round nose) and the cutting edge.
min.
3 mm (0.11Ó)
The best results are obtained with a depth-limiter depth of
0.64 mm (.025”).
CAUTION: Excessive depth
increases the risk of kickback!
B
19
Download from Www.Somanuals.com. All Manuals Search And Download.
All cutters must be sharpened to the same angle, 30°. Different
angles result in a roughly, irregularly running chain, increase
wear and tear and cause chain beakage.
The 85° front rake of the cutter results from the cut depth of
the round file. If the proper file is used in the right manner, the
correct front rake will be obtained automatically.
C
Files and how to work with them
Use a special round file for chains (dia. 4 mm) for sharpening
the chain. Normal round files are not appropriate for this work.
See „Accessories“ for the order number.
The file should cut only when pushed forwards (arrow). Lift the
file when leading it backwards.
First sharpen the shortest cutter. The length of this cutter is then
the standerd for all other cutters of the chain.
New saw teeth must be filed to the exact same shape as the
used teeth, including on their running surfaces.
Chain typ
466
Chain typ
092
File depending on chain type (90° or 10° to the guide bar).
D
The file holder makes file guidance easier. It is marked for the
correct 30° sharpening angle (keep the marks parallel with the
chain when filing, see illustration) and limits the cut depth to
the correct 4/5 of the file diameter. See „Accessories“ for the
order number.
4/5
30°
E
After having sharpened the chain, the height of the depth limiter
mustbecheckedbymeansofachaingauge. See„Accessories“
for the order number.
Correct even the smallest excess height with a special flat
file (12). See „Accessories“ for the order number.
Round off the front of the depth limiter (13).
12
13
F
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the sprocket interior, checking and
replacing the chain catch sleeve
CAUTION:Beforedoinganyworkontheguidebarorchain,
always switch off the engine and pull the plug cap off the
spark plug (see „Replacing the spark plug“). Always wear
protective gloves!
CAUTION: Do not start the saw until it has been completely
assembled and inspected!
Remove the sprocket guard (4) (see section on „PUTTING INTO
OPERATION“ A – B) and clean the interior with a brush.
1
2
3
Remove the chain (3) and guide bar (2).
NOTE:
Make sure that no residue or contaminants remain in the oil
guide groove (1) and the chain tightener (6).
5
4
For replacing the guide bar, chain, and sprocket see „PUTTING
INTO OPERATION“.
6
Chain catch sleeve
Visually inspect the chain catch sleeve (5) for damage and
replace if necessary.
Remove the sleeve by firmly pulling it upwards and off; then
push on the new sleeve.
A
Cleaning the guide bar,
lubricating the sprocket nose
CAUTION: Protective gloves must be worn.
Regularly inspect the bearing surfaces of the guide bar for
damage, and clean them with a suitable tool.
If the saw is used intensively it will be necessary to lubricate the
returnsprocketbearingsregularly(onceaweek).Todothis, first
thoroughly clean the 2 mm hole at the tip of the guide bar, and
then press in a small amount of multi-purpose grease.
Multi-purpose grease and grease guns are available as acces-
sories.
Multi-purpose grease
Grease guns
(order number 944 360 000)
(order number 944 350 000)
B
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the saw chain
7
CAUTION: Use only chains and guide bars designed for
this saw (see the Extract from the spare-parts list)!
Check the sprocket (7) before mounting a new chain.
Remove the sprocket guard (see ”PUTTING INTO OPERATI-
ON” A-H)
CAUTION: Worn out sprockets (8) may damage the new chain
and must therefore be replaced.
Replacing the clutch drum and sprocket
8
Release the chain brake if necessary.
Lever off the circlip (11) using the universal wrench and remove
the washer (10).
9
10
11
Pull off the clutch drum together with the sprocket (9) and fit a
new clutch drum and sprocket in reverse order.
C
Replacing the suction head
The felt filter (12) of the suction head can become clogged.
It is recommended to replace the suction head once every
three months in order to ensure unimpeded fuel flow to the
carburetor.
To remove the suction head for replacement, pull it out through
the tank filler neck using a piece of wire bent at one end to
form a hook.
12
D
Cleaning the air filter
Unscrew screw (14) and remove the filter cover (13).
IMPORTANT: Cover the intake opening with a clean cloth in
order to prevent dirt particles from falling into the carburetor.
Remove the air filter.
13
14
CAUTION: To prevent injury to the eyes, do NOT blow out
dirt particles! Do not use fuel to clean the air filter.
Clean the air filter with a soft brush.
If the filter is very dirty, clean it in lukewarm water with dish-
washing detergent.
Let the air filter dry completely.
If the filter is very dirty, clean it frequently (several times a day),
because only a clean air filter provides full engine power.
CAUTION:
Replace damaged air filters immediately.
Pieces of cloth or large dirt particles can destroy the
engine!
E
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the spark plug
CAUTION:
Do not touch the spark plug or plug cap if the engine is
running (high voltage).
Switchofftheenginebeforestartinganymaintenancework.
A hot engine can cause burns. Wear protective gloves!
0,5 mm
The spark plug must be replaced in case of damage to the
insulator, electrode erosion (burn) or if the electrodes are very
dirty or oily.
Pulltheplugcap(1)offthesparkplug. Useonlythecombination
wrench supplied with the saw to remove the spark plug.
CAUTION: Use only the following spark plugs: NGK BPMR 7A.
Electrode gap
1
The electrode gap must be 0.5 mm.
A
Replacing the starter cable
Unscrew four screws (2). Remove fan housing (3).
Remove all pieces of cable.
Unscrew screw (4). Hold the cable drum (7) firmly and remove
the drive spindle (5) and spring (6).
CAUTION: Danger of injury! The return spring unit (9) is
not secured and can fall out of the fan housing. The return
spring is under tension and pop out of the unit! If this hap-
pens, the spring can be replaced in the unit as shown in the
illustration (note the direction of rotation!).
Secure the return spring unit (9) against falling out and care-
fully take off the cable drum (7).
Thread a new cable (dia. 3 mm, length 900 mm), as shown in the
illustration (note the stop (11)) and tie a knot in both ends.
Pull the knots (12) into the cable drum (7) and starter handle (10).
Put the cord drum back on and turn gently until the return spring
catches.
Install the drive spindle (5) and spring (6), screw in the screw
(4) and tighten.
2
3
Guide the cable into the space (8) on the drum and use the
cable to turn the drum two turns clockwise.
12
11
Hold the cable drum with your left hand and with your right hand
untwist the cable, pull it tight and hold it.
10
Carefully release the cable drum. The spring will wind the cable
around the drum.
9
Repeat three or four times. The starter grip should now be held
upright on the fan housing.
8
7
CAUTION: Danger of injury! Secure the cable grip when
pulled out! It will whip back if the cable pulley is released
by accident.
6
5
NOTE: With the cable pulled all the way out, it must still be
possible to turn the pulley another 1/4 turn against the return
spring.
When replaceing fan housing, it may be necessary to pull the
starter cable lightly so that the cable pulley catches.
12
4
B
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the return spring unit
9
Remove and reinstall the fan housing and cable drum (see
”Replacing the starter cable”).
Carefully remove the return spring unit (9) from the fan
housing.
CAUTION:
Danger of injury! If the spring is broken it can jump out!
Carefully fit the new return spring unit.
C
Cleaning the muffler
CAUTION: If the engine is hot there is a risk of burning.
Wear protective gloves.
Remove the sprocket guard (see ”PUTTING INTO OPERATI-
ON” Fig. B).
Remove deposits of carbon from the exhaust outlets (13) of
the muffler.
13
D
14
Cleaning the cylinder space
15
Remove the sprocket guard (see ”PUTTING INTO OPERATI-
ON” Fig. B).
If necessary remove muffler by loosening and removing the
three screws (16).
16
Stuff a rag into the cylinder port (17).
Use a suitable tool (wooden scraper) to clean out the cylinder
space (18), especially the cooling fins.
Remove the rag from the cylinder port and refit the muffler
according to the diagram.
Replace the gasket (15) and cowling (14) if necessary. Carefully
remove any pieces of the old gasket from the muffler.
Ensure correct mounting position. The cowling should follow
the contour of the cylinder to ensure correct heat transfer.
Tighten screws (16) to 10 Nm while the engine is cold.s
17
18
E
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be
performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the
prescribed maintenance work can lead to accidents!
The user of the chain saw must not perform maintenance work which is not described in the instruction manual. All such work must
be carried out by a MAKITA service centre.
Page
General
Chain saw
Clean exterior, check for damage. In case of damage,
have repaired by a qualified service centre immediately
Saw chain
Chain brake
Guide bar
Sharpen regulary, replace in good time
19-20
12
Have inspected regularly at an authorized service centre
Turn over to ensure even wear of bearing surfaces
Replace in good time
Before each start
Saw chain
Inspect for damage and sharpness
Check chain tension
19-20
12
Guide bar
Check for damage
Functional check
Functional check
Chain lubrication
Chain brake
15
17
OFF switch,
Safety locking button,
Throttle lever
Functional check
16
Fuel/oil tank
plug
Check for tightness
Every day
Air filter
Clean
22
15
Guide bar
Check for damage, clean oil intake bore
Clean, in particular the oil guide groove
Check (chain must not run)
Guide bar support
Idle speed
15, 21
17-18
Every week
Fan housing
Cylinder space
Spark plug
Clean to ensure proper air cooling
Clean
23
24
23
24
21
Check and replace if necessary
Check tightness of mounting
Muffler
Chain catch sleeve
Screws and nuts
Check for damage, replace if necessary.
Check their condition and that they are firmly secured.
Every 3 months
Storage
Suction head
Fuel, oil tanks
Replace
Clean
22
Chain saw
Clean exterior, check for damage. In case of damage,
have repaired by a qualified service centre immediately
Guide bar/chain
Demount, clean and oil slightly
Clean the guide groove of the guide bar
Empty and clean
21
Fuel, oil tanks
Carburetor
Run empty
Service, spare parts and guarantee
Maintenance and repair
The maintenance and repair of modern engines as well as all safety devices require qualified technical training and a special work-
shop equipped with special tools and testing devices.
We therefore recommend that you consult a MAKITA service centre for all work not described in this instruction manual.
The MAKITAservice centres have all the necessary equipment and skilled and experienced personnel, who can work out cost-effective
solutions and advise you in all matters.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare parts
Reliable long-term operation, as well as the safety of your chain saw, depend among other things on the quality of the spare parts
used. Use only original MAKITA parts, marked
Only original spare parts and accessories guarantee the highest quality in material, dimensions, functioning and safety.
Original spare parts and accessories can be obtained from your local dealer. He will also have the spare part lists to determine the
required spare part numbers, and will be constantly informed about the latest improvements and spare part innovations.
Please bear in mind that if parts other than original MAKITA spare parts are used, this will automatically invalidate the MAKITA
product guarantee.
Guarantee
MAKITA guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting
from material or production faults occurring within the guarantee period after purchase. Please note that in some countries particular
guarantee conditions may exist. If you have any questions, please contact your salesman, who is responsible for the guarantee of
the product.
Please note that we cannot accept any responsibility for damage caused by:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Disregard of the instruction manual.
Non-performance of the required maintenance and cleaning.
Incorrect carburetor adjustment.
Normal wear and tear.
Obvious overloading due to permanent exceeding of the upper performance limits.
Use of guide bars and chains which have not been approved.
Use of guide bar and chain lengths which have not been approved.
Use of force, improper use, misuse or accidents.
Damage from overheating due to dirt on the fan housing.
Work on the chain saw by unskilled persons or inappropriate repairs.
Use of unsuitable spare parts or parts which are not original MAKITA parts, insofar as they have caused the damage.
Use of unsuitable or old oil.
Damage related to conditions arising from lease or rent contracts.
Damages caused by disregarding loose outer bolted connections.
Cleaning, servicing and adjustment work is not covered by the guarantee. All repairs covered by the guarantee must be performed
by a MAKITA service centre.
Trouble shooting
Malfunction
System
Observation
Engine runs
Ignition spark
No ignition spark
Fuel tank is filled
Inside
Cause
Chain does not run
Chain brake
Ignition system
Chain brake actuated.
Engine does not start or
only with difficulty
Malfunction in fuel supply system, com-
pression system, mechanical malfunction.
Sitch on STOP, fault or short-circuit in the
wiring, plug cap or spark plug defective.
Choke in wrong position, carburetor defective,
suction head dirty, fuel line bent or interrupted.
Faulty crankcase gasket, radial shaft
packings defective, cylinder or piston rings de
fective
Fuel supply
Compression
system
Outside
Spark plug does not seal.
Mechanical
malfunction
Starter does not engage
Spring in starter broken, broken parts
inside the engine.
Warm start difficulties
Carburetor
Fuel supply
Fuel tank is filled
Ignition spark
Wrong carburetor adjustment.
Engine starts, but
dies immediately
Fuel tank is filled
Wrong idling adjustment, suction head or
carburetor dirty. Tank venting defective, fuel
line interrupted, cable defective, STOP switch
defective.
Insufficient power
Several systems
may be involved
simultaneously
Engine is idling
Air filter dirty, wrong carburetor adjustment,
muffler clogged,exhaust channel in cylinder
clogged.
No chain lubrication
Oil tank/pump
No oil on the chain
Oil tank empty.
Oil guide groove dirty.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Extract from the spare parts list
Use only original MAKITA parts. For repairs and replacement
of other parts, see your MAKITA service centre.
DCS3410TH
Pos. MAKITA-No. Qty. Denomination
1
442 030 661
442 035 661
442 030 471
442 035 471
1
1
1
1
Sprocket nose bar 30 cm (12”) 3/8”
Sprocket nose bar 35 cm (14”) 3/8”
Carving bar 30 cm (12”), 1/4”
Carving bar 35 cm (14”), 1/4”
2
528 092 646
528 092 652
512 466 668
512 466 676
1
1
1
1
Saw chain 3/8” for 30 cm
Saw chain 3/8” for 35 cm
Saw chain 1/4” for 30 cm
Saw chain 1/4” for 35 cm
3
4
5
6
7
8
9
952 010 630
941 719 131
963 601 121
170 114 100
963 225 030
021 164 010
170 163 100
1
1
1
1
1
1
1
1
1
1
1
2
Chain protection for 30-35 cm
Universal wrench SW 13/19
Suction head
Tank cap, cpl.
O-Ring dia. 25 mm
Starter cable 3x900 mm
Return spring unit
3/8” sprocket cpl.
1/4” sprocket cpl.
Spark plug
10 170 223 100
10 170 223 200
11 965 603 021
12 170 173 020
4
3
Air filter
-
923 208 004
Hexagonal nut M8
(for sprocket guard)
1
2
-
170 213 100
1
Chain catch sleeve
10
12
Identification plate
Indicate when ordering spare parts
DCS3400TH
2009 123456
Serial number
Year of manufacture
8, 9
5, 6, 7
22045 Hamburg, Germany
11
6, 7
XXX.XXX.XXX
Typ 170
16
17
18
19
Accessories (not delivered with the chain saw)
15 953 100 090
16 953 004 010
17 953 003 090
18 953 003 060
19 953 030 010
1
1
1
1
1
Cain gauge
File handle
Round file dia. 4 mm
Flat file
File holder
(with round file dia. 4 mm)
Carburetor screwdriver
Two-stroke engine oil (1 l)
Two-stroke engine oil (100 ml)
BIOTOP-chain oil (1 l)
BIOTOP-chain oil (5 l)
20 944 340 001
1
1
1
1
1
1
-
-
-
-
-
980 008 107
980 008 106
980 008 210
980 008 211
949 000 035
15
20
Combined can (for 5l fuel.,
2,5l chain oil)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
To find your local distributor,
Makita Werkzeug GmbH
Postfach 70 04 20
D–22004 Hamburg
Germany
Specifications subject to change without notice
Form: 995 707 421 (7.09 GB)
Download from Www.Somanuals.com. All Manuals Search And Download.
|