VCR
VR400BMG
Video Ca ssette Recorder
Hookup Pa ges
Download from Www.Somanuals.com. All Manuals Search And Download.
Hookups With a Cable Box / Direct Broadcast System (cont’d) 9
With this connection:
● You may watch one channel while recording another.
● You may not record scrambled channels.
VCR
1
Cable Box/DBS
2
75
⍀
ANT /
CABLE
ANT
IN
AU
IN
IN
OUT
OUT
OUT
CH3 C
VIDEO
RF coaxial
cable
Cable
Signal
TV’s ANTENNA
IN Jack
RF coaxial
cable
3
Connections
1
Connect a Cable signal to the VCR’s ANT(enna) IN Jack.
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on
the VCR to the IN Jack on the Cable Box/DBS.
3
Use a second RF coaxial cable to connect the OUT Jack on the
Cable Box/DBS to the ANTENNA IN Jack on the TV.
Recording O ne Channel/W atching Another
1
Put the Cable Box/DBS on the sam e channel as the
VCR’s CH3/CH4 switch. (Make sure the TV is on the Cable
Box/DBS output channel, 03 or 04.)
Then, with the VCR in VCR position (the VCR/TV light
will appear on the display panel), use the CHANNEL
o/p buttons to select the channel you want to record at
the VCR. Start the recording.
2
Press the VCR/TV button once to put the VCR in TV
position. (The VCR/TV light will disappear.)
Helpful Hint
• When you play a tape, make sure
the Cable Box/DBS is set to the
same channel as the CH3/CH4
switch on the VCR. Set the TV to
the Cable Box/DBS output channel
(03 or 04).
3
Select the channel you want to watch at the Cable
Box/DBS.
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Hookups With a Stereo TV
antenna or
cable to
ANT(enna)
IN Jack
1
ANT
IN
AUDIO
IN
OUT
OUT
CH3 CH4
VIDEO
Audio and Video
IN Jacks on TV
VIDEO (yellow) and
AUDIO (white) OUT Jacks
Video Cable
2
Audio Cable
3
● Audio and Video cables are not supplied.
1
Connect the antenna or cable to the ANT(enna) IN Jack
on the back of the VCR.
2
Connect a video cable to the yellow VIDEO O UT Jack on
the back of the VCR. Then, connect the other end of the
video cable to the VIDEO IN Jack on your TV.
3
Connect an audio cable to the white AUDIO O UT Jack
on the back of the VCR. Then, connect the other end of
the audio cable to the AUDIO IN Jack on your TV.
(If your TV has Right and Left AUDIO IN Jacks, you must use a
“Y” splitter audio cable as illustrated to deliver audio to the TV’s
right and left channels.)
4
Turn on your TV, making sure it is in Line Input mode. Please
refer to your TV owner’s manual for details.
Helpful Hint
• This hookup will not give you stereo
sound. To get stereo sound, use the
connections on pages six-seven and
select the channel to be viewed at
the TV (with the VCR turned off).
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel 21
Rem ote Sensor
F.FW D (Fast Forward) Button
Receives a signal from your remote
control so you can operate your VCR
from a distance.
When tape playback is stopped, press to fast forward the
tape at high speed. During tape playback, press to fast for-
ward the tape while the picture stays on the screen. Details
are on page 35. Press to select an item in the VCR menu.
VCR/TV Button
Use to select the signal that
your TV receives.
● VCR Position
PLAY Button
Press to play a tape. Also, press to release Slow,
Search, or Still mode and return to normal play-
back. Details are on page 35.
Use to watch a tape, to
watch a program while
recording it, or to watch a
TV broadcast using the
CHANNEL o/p or Number
buttons to change channels at
the VCR. The VCR/TV light
will appear when the VCR is
in VCR position.
Press to select an item in the VCR menu.
STO P/EJECT Button
Press once to stop the tape. When tape
playback is stopped, press to eject the tape.
Press to select an item in the VCR menu.
REW (ind) Button
When tape playback is stopped, press to rewind
the tape at high speed. During tape playback,
press to rewind the tape while the picture stays
on the screen. Details are on page 35. Press to go
back one step when setting the clock or a timer
recording.
● TV Position
Use to watch TV (changing
channels at the TV) or to
watch one program while
recording another. Details are
on page 32.
PLAY
REW
F.FWD
REC/OTR STOP/EJECT
PAUSE
MENU
POWER VCR/TV CST.IN
TIMER
REC
POWER
VCR/TV
SPEED
CHANNEL
SPEED Button
PO W ER Button
Press to turn the VCR
power on and off.
Press to select the recording speed
(SP or SLP). Details are on pages 24
and 44.
CHANNEL o/p Buttons
Press to scan up or down through the VCR’s channels.
TRACKING Function
During normal tape playback or slow motion tape playback, press the
CHANNEL o/p buttons to adjust the tracking. Details are on page 41.
REC(ord)/O TR Button
Press once to start a recording. Details are on page 24. Press repeatedly to start a One-
Touch Recording (an immediate recording, 30 minutes to eight hours long) of the channel
you are watching. Details are on page 25.
PAUSE Button
While recording, press to temporarily stop the recording. Press a second time to resume normal
recording. Details are on page 24. You can not pause a One-Touch Recording. Details are on page
25. During tape playback, press to freeze the picture. Press repeatedly to advance the still picture
frame by frame. Details are on page 35.
MENU Button
Press repeatedly to access menus or to remove menus.
Download from Www.Somanuals.com. All Manuals Search And Download.
22 Rear Panel
ANT(enna) IN Jack
Connect your antenna or cable
here. Details are on pages six-10.
AUDIO IN Jack
Connect a cable coming from the
audio out jack of a camcorder,
another VCR, or an audio source
here. Details are on page 33.
AUDIO O UT Jack
Connect a cable going to the
audio in jack of a camcorder,
another VCR, or an audio system
here. Details are on page 33.
ANT
IN
AUDIO
IN
OUT
OUT
CH3 CH4
VIDEO
VIDEO O UT Jack
Connect a cable going to the video
in jack of a camcorder, another
VCR, or an audio-visual system
(laser disc player, video disc player,
etc.) here. Details are on page 33.
CH3/CH4 Switch
Set to channel 3 or 4
to use your TV with
your VCR. Set your
TV to the same chan-
nel. Details are on page
seven.
VIDEO IN Jack
AC Power Cord
Connect to a standard AC outlet
to supply power to the VCR.
Connect a cable coming from
the video out jack of a cam-
corder, another VCR, or an
audio-visual source (laser disc
player, video disc player, etc.)
here. Details are on page 33.
O UT Jack
Use the supplied RF coax-
ial cable to connect this
jack to the Antenna In
Jack on your TV or Cable
Box/DBS. Details are on
pages six-nine.
Download from Www.Somanuals.com. All Manuals Search And Download.
Rerecording (Tape Duplication) 33
1. Audio cable from AUDIO O UT Jack of
VCR 1 to AUDIO IN Jack of VCR 2
VCR 1
Playing VCR
VCR 2 - Recording VCR
ANT
ANT
IN
IN
AUDIO
AUDIO
IN
OUT
IN
OUT
OUT
OUT
CH3 CH4
CH3 CH4
VIDEO
VIDEO
3. RF coaxial
cable from the
O UT jack of
VCR2 to the TV’s
ANTENNA IN
Jack
2. Video cable from VIDEO O UT Jack
of VCR 1 to VIDEO IN Jack of VCR 2
1
VCR 1 will play your tape. Insert a prerecorded tape in
VCR 1. If the tape does not have a record tab, playback begins. If
this happens, press the STOP/EJECT button on VCR 1 once.
2
VCR 2 will record your tape. Insert a blank tape in VCR 2.
Make sure the record tab is intact (details are on page five). Make
sure the VCR 2 power is on and VCR 2 is in VCR position. (The
VCR/TV light will appear. If it does not, press the VCR/TV button
once.)
3
Turn on the TV and set it to channel 3 or 4, whichever
channel the CH3/CH4 switch on VCR 2 is set to.
4
Point the rem ote control at VCR 2. Press the Num ber
buttons 0, 0. LineIn Rear (L1) will appear on the screen.
Helpful Hints
• Unauthorized recording of copy-
righted television programs, video
tapes, or other materials may
infringe on the rights of copyright
owners and violate copyright laws.
• If a program has copyright protec-
tion, it may not record clearly.
• Audio and video cables are not sup-
plied.
• The illustration uses two VCRs just
like yours. Different VCRs may oper-
ate differently.
• When LineIn Rear (L1) appears on
the screen, the screen will be blue.
5
Point the rem ote control at VCR 2. Use the SPEED but-
ton to select SP or SLP.
6
Press the PLAY button on VCR 1 and the REC(ord)/O TR
button on VCR 2 at the sam e tim e.
7
To stop recording, press the STO P/EJECT button on VCR
2 once, then stop the tape on VCR 1.
Download from Www.Somanuals.com. All Manuals Search And Download.
|