Owner’s Manual
7" Black and White Rearview
Security Camera System
Model: MCS-700BW
For Technical Assistance, please call (800) 638-3600,
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor Features
1
2
3
4
SELECT
5
6
7
8
9
10
1. LED Power Indicator
2. Power Button
7. Contrast Control
8. Brightness Control
3. Camera Selection Button
4. Day/Night Selection Button
5. LED Camera Selection Indicators
6. Volume Control
9. Mode Selection Button
10. Internal Speaker (Side of Housing)
General Operation
The MCS-700BW back up safety device uses a 7" black and white monitor and a rear mounted
camera (and optional side cameras) to allow a clear view and audio of the area immediately
behind your vehicle. The back up safety device will automatically activate when the ignition key
is turned on and the vehicle is put into reverse.
Note 1: If the screen is dark when the vehicle is in reverse, make sure the monitor’s power but-
ton is in the "On" position.
Note 2: If the screen is displaying the wrong image when vehicle is in reverse, make sure the
monitor’s mode selection button is set to the “AUTO” position.
7" Black and White Monitor
All the controls to operate your monitor are located on the front panel. Familiarize yourself
with the monitor’s features so you can adjust settings to suite your personal preference (See
Monitor Basic Features).
Rear View Camera
The rear view camera will automatically activate when the ignition key is turned "On" and the
vehicle is put into reverse. The video image from the camera will appear on the monitor and
the audio from the camera can be heard through the monitor’s speaker.
Note: This system only provides for one way audio, from the camera to the monitor. The mon-
itor is unable to transmit audio to the camera.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor Basic Features
1. LED Power Indicator
When illuminated the monitor is "On".
2. Power Button
This button turns the monitor "On" and "Off".
Note: The ignition key must be switched to the "On" position for proper operation.
3. Camera Selection Button
If your vehicle has two or more cameras press this button to display other cameras views on
the monitor.
Note 1: The ignition key must be switched to the "On" position.
Note 2: Camera 1 (C1) has priority over any other cameras and will automatically activate when
the vehicle is put into reverse providing the mode selection button is set to the “AUTO” posi-
tion.
Note 3: If a camera is not connected to a selected source the monitor's picture will be blank.
4. Day/ Night Selection Button
This button adjusts the monitor for daytime or nighttime operation.
5. LED Camera Selection Indicators
If your vehicle has more than one camera the LED camera indicators will identify which cam-
era view is being displayed on the monitor.
6. Volume Control
Knob adjusts the volume of the audio from the camera’s microphone.
7. Contrast Control
Adjust the monitor’s contrast between black and white with this knob.
8. Brightness Control
This knob adjusts the monitor’s overall brightness.
9. Mode Selection Button
Single Camera System
MAN (manual) position: Refer to the LED camera selection indicators to identify what
camera is being displayed on the monitor. If your system has a single camera (C1) the
monitor will show the rear camera view. If C2, C3 or C4 are selected the monitor’s pic-
ture will be blank. When the vehicle is put into reverse the camera view will NOT auto-
matically change to the rear view camera (C1).
AUTO (automatic) position: Refer to the LED camera selection indicators to identify what
camera view is being displayed on the monitor. If your system has a single camera (C1)
the monitor will show the rear camera view. If C2, C3 or C4 are displayed the monitor’s
picture will be blank. When the vehicle is put into reverse the camera view will automat-
ically change the picture to the rear view camera (C1).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
(continued)
Monitor Basic Features
Multiple Camera System
MAN (manual) position: Refer to the LED camera selection indicators to identify what
camera view is being displayed on the monitor. If your system has multiple cameras (C1)
will show the rear camera view. If C2, C3 or C4 are selected the monitor’s picture will
show the view of camera selected. When the vehicle is put into reverse the camera view
will NOT automatically change to the rear view camera (C1).
AUTO (automatic) position: Refer to the LED camera selection indicators to identify what
camera view is being displayed on the monitor. If your system has a multiple cameras
(C1) will show the rear camera view. If C2, C3 or C4 is selected the monitor’s picture will
show the view of the camera selected. When the vehicle is put into reverse the camera
view will automatically change the picture to the rear view camera (C1).
Camera Basic Features
2
3
1
4
1. Microphone: Allows for audio transmission to the monitor’s internal speaker.
2. Illumination LEDs
3. Lens
4. Photo Sensor: Illuminates the LED under low-light conditions.
Note: This Rearview Security System has a CCD camera which uses LEDs to brighten-up the
area under low-light conditions. The camera is not capable of night vision, but can brighten the
area enough so you may be able to detect objects on your monitor. As a result, extra care should
be taken under nighttime, dusk or low-light conditions.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Although this Rearview Security System requires little care, you can still maintain its condition
and performance by following these steps:
• Keep the system away from excessive moisture, extreme heat or cold, and magnetic fields.
• Occasionally clean the camera lens and monitor screen with damp soft cloth.
Should you experience any problem with the system please refer to the troubleshooting guide
prior to returning your system for repair.
Note 1: The user should not attempt to service the unit beyond that described in the operating
instructions. All other servicing should be referred to qualified personnel.
Note 2: Do not expose the unit to water or excessive moisture. This could cause electrical
shorts, fire or other damage.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Only qualified personnel should remove the cover or service this unit. The warranty will become invalid
if factory security seal is broken.
Solutions
Symptoms
Unstable Image
• Low Voltage, Check Battery
• Check Generator
Cloudy Image
No Power
• Clean Dirty Camera Lens
• Clean Dirty Monitor Lens
• Adjust Contrast
• Adjust Brightness
• Check Fuse in the Monitor Wiring Harness
• Camera or Bracket may have been
Damaged or Moved
Specifications
Monitor:
Camera:
CRT:
Deflection Angle:
Input Voltage:
Output Voltage:
Power Consumption:
Screening Frequency:
7"
90°
Image Sensor Type:
TV System:
Effective Pixels:
Sensing Area:
CCD
CCIR
EIA
11V ~ 32V (DC)
10.5V 0.2V (DC)
18W
CCIR (H) 15625Hz (V)50Hz
EIA (H) 15750Hz (V)60Hz
1V (p-p) 20%
1V (p-p)
550 x 580 510 x 492
4.9 x 3.7mm
CCD
Image Sensor Type:
Video Input:
Video Output:
Horizontal Resolution: 600 TV Line Maximum
Field Resolution:
Anti-Vibration:
Camera Output Port:
A/V Port:
Speaker Size:
Use Temperature:
Dimensions:
400 TV Line Maximum
8G
DIN Socket
RCA Socket
2.5"
-35°C - +60°C
203(W) x 153(H) x 219(L) mm
11 LBS.
Weight:
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within one year from the date of sale
to you, repair, replace or refund the retail sales price of said product or any part thereof, at
the option of the Magnadyne Corporation or its authorized agents, if said product or part
is found defective in materials or workmanship, when properly connected and operating on
the correct power requirements designated for the specific product. This warranty and
Magnadyne Corporation or its authorized agent’s obligations hereunder do not apply where
the product was; damaged while in the possession of the consumer, subjected to unrea-
sonable or unintended use, not reasonably maintained, utilized in commercial or industrial
operations, or serviced by anyone other than Magnadyne Corporation or its authorized
agents, or where the warning seal on the product is broken or the power and/or plugs are
detached from the unit. Magnadyne Corporation or any of its authorized agents will not
assume any labor costs for the removal and reinstallation of any product found to be defec-
tive, or the cost of transportation to Magnadyne Corporation or its authorized agents. Such
cost are the sole responsibility of the purchaser.
This warranty does not cover the cabinet appearance items or accessories used in con-
nection with this product, or any damage to recording or recording tape, or any damage to
the products resulting from improper installation, alteration, accident, misuse, abuse or
acts of nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO
ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE
ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN
EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND
ONE YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not
transferable. Some states do not allow limitations on how long an implied warranty lasts,
and some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may have other rights that vary from state to state.
“NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the User’s
authority to operate the equipment.”
Defective merchandise should be returned to the original point of purchase or
secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220.
Return Authorization must be obtained before sending, or merchandise may be refused.
Copyright © 2007 MobileVision
Magnadyne Corp.
MCS-700BW-UM Rev. A 2-13-07
Download from Www.Somanuals.com. All Manuals Search And Download.
|