Magnadyne Remote Starter X11 User Manual

Owner’s  
Manual  
Model: X11  
For Technical Assistance, please call (800) 638-3600,  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Congratulations on your purchase of a quality Marksman automotive security and remote start  
system. Marksman security products have been designed to provide the consumer with a  
technologically superior product with years of trouble free operation. The information enclosed will  
provide a ready reference of the operation and maintenance of your new Marksman security and  
remote start system.  
Remote Control Transmitters  
The LCD screen on the remote control displays graphic icons. It provides you visual information on  
any trigger of the sensors and around the clock surveillance to your vehicle as well as showing the  
present status of the system.  
IGN  
ARM  
2-Way  
LCD  
Remote  
LCD  
Display  
Icons  
1-Way  
Backup  
Remote  
Battery Replacement  
The two-way LCD remote control is powered by a 1.5V type AAA high power digital camera battery.  
When the power of the battery weakens 3 things will happen to indicate a low battery.  
1. All the LCD icons on the display will turn off and only the battery icon  
will be flashing.  
2. The two-way reporting function will turn off to preserve remaining battery power until a  
replacement battery is installed.  
3. When the buttons on the transmitter are pressed you will hear 3 beeps.  
When the old battery is replaced with a new one, there will be a melody playing to indicate the  
power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons.  
Correct the time by pressing SET for 3 seconds before using.  
Note: Even if the battery is replaced, your programmed set values shall remain unchanged. The  
remote control automatically reads and memorizes all the previous set information saved in the  
main control module.  
Press the  
button two times  
when the battery compartment  
is empty, then insert the new  
battery.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
LCD Transmitter Operation  
Transmitter Button  
System Function  
Remark  
Locks Doors & Arms System  
Arm and Bypass the 2 Stage  
Shock Sensor (Zone 4)  
Press Twice within 3 Seconds  
Press within 5 Seconds  
-
-
Arm and Bypass the 2nd  
Sensor (Zone 6)  
Arm and Bypass  
Sensor 1 and 2  
Press within 5 Seconds  
-
-
Arm and Activate Hidden Alarm Function  
Car Locator  
Press within 3 Seconds  
-
Wait for 30 Seconds After Arming  
Press and Hold for 3 Seconds  
Ignition in “OFF” Position  
Hold for 3  
Seconds  
Remote Panic Function  
Silent Arming/Disarming  
Active Anti-Car Jacking Mode  
Unlock Doors & Disarm Alarm  
Two Step Door Unlock &Disarm Alarm  
Trunk Release (Channel #3)  
Automatic Arming Bypass  
Activate or Turn Off the Remote Start  
Channel #4 Output (4)  
+
Ignition in “ON” Position,  
Press and Hold for 2 Seconds  
Hold for 2  
Seconds  
+
Press Unlock Twice within 3 Seconds  
Press and Hold for 1.5 Seconds  
Alarm Must be in Disarmed Mode  
Press Twice within 3 Seconds  
Press Together and Release  
Press Together and Release  
Press Together and Release  
Press Together and Release  
-
-
-
+
+
Channel #5 Output (5)  
Channel #6 Output (6)  
+
Channel #7 Output (7)  
+
Switch Transmitter Operation  
to the Second Car/System  
Press and Release trunk, Then press Lock-  
Unlock Together  
-
+
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
LCD Display Transmitter Operations  
Transmitter Button  
System Function  
Remark  
System Trigger Record Check  
Press within 3 Seconds  
-
SET  
-
-
System Status Check  
Optional Driving Pager  
Press within 3 Seconds  
Press within 3 Seconds  
Press within 3 Seconds  
SET SET  
-
-
=
SET  
SET  
Monitor Interior Temperature  
=
Chirp Indicators  
Chirp  
Function  
1 Chirp  
System is Armed  
System is Disarmed  
2 Chirps  
3 Chirps  
4 Chirps  
2, 3, 6 Chirps  
Defective Sensor of Open Door Reminder  
Disarm / Previously Triggered  
Car Locator  
Parking Light  
Flash  
Function  
1 Flash  
System is Armed  
2 Flashes  
3 Flashes  
2 - 3 - 6 Flashes  
Constant On  
System is Disarmed  
Disarmed / Triggered  
Car Locator  
Engine Running Under Remote Start (Default Setting)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
LED Display  
LED  
Function  
OFF  
System is Disarmed  
Slow Flashing  
Fast Flashing  
On Solid  
System is Armed  
System in Passive Arming  
System in Valet Mode  
1 Flash - Pause  
2 Flashes - Pause  
3 Flashes - Pause  
4 Flashes - Pause  
5 Flashes - Pause  
6 Flashes - Pause  
Zone 1, Trigger for Hood  
Zone 2, Trigger on Trunk  
Zone 3, Trigger on Door Switch  
Zone 4, Trigger on Sensor #1  
Zone 5, Trigger on Ignition Switch  
Zone 6, Trigger on Sensor #2  
System Characteristics  
Siren/Horn Parking Light  
1 or 3 Chirps 1 Flash  
2. Disarming 2 to 4 Chirps 2 or 3 Flashes  
LED  
Doors  
Starter Dome Light  
1. Arming  
Slow Flash Locking Disabled  
Unlocking  
Turns on for  
30 Seconds  
3. Trigger  
4. Panic  
Alarming  
Alarming  
Flashing  
Flashing  
Pause Flash  
Disabled  
Flashes  
Flashes  
5.Car  
Jacking  
Alarming  
Flashing  
Disabled  
Flashes  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual Arming: Lock and Arm  
1.Press the button on the transmitter.  
2.The siren will chirp once and parking lights will flash once indicating that the system is now  
armed. The vehicle door will lock upon arming when interfaced with the security system.  
System Armed  
Door Ajar  
Trunk/Hood Ajar  
Clear the Flash Icon:  
Press the SET button 3 times  
within 3 seconds to clear the  
flash icon on the LCD screen  
transmitter.  
ARM  
ARM  
ARM  
Door Ajar / Defective Sensor Reminder  
If the siren sounds 3 times, there is a Door, Trunk, or Hood left open.  
Silent Arming/Disarming  
Pressing the transmitter  
and  
button at the same time will arm or disarm your security  
system, No chirp sound will be heard, arm/disarm confirmation will be through the vehicles  
parking lights only.  
Shock Sensor Bypass (Sensor #1)  
Press the button on the transmitter two times within 3 seconds. This will arm the security  
system and bypass the shock sensor.  
Sensor Bypass (Sensor #2)  
Press the button first, within 3 seconds, press the  
the security system and bypass the #2 sensor.  
button on the transmitter. This will arm  
All Sensor Bypass (Sensor #1 and #2)  
Press the button first, within 3 seconds, press the  
button on the transmitter (2) times. This  
will arm the security system and bypass both electronic sensor ports.  
Notes on Remote Sensor Bypass: The sensor bypass feature is programmed to activate for one  
arming cycle only. The security system will return to normal operation during the next arming cycle.  
(Applies only when Automatic Arming is Programmed On)  
Automatic Arming  
This security system is equipped with an optional automatic arming feature which allows the  
security system to arm 30 seconds after the last door is closed. Operation is as follows:  
1. Turn the ignition to the “OFF” position and exit the vehicle.  
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you re-  
open any protected entrance, the security system LED will stop flashing. It will begin flashing  
again once the vehicles entrances are closed.  
3. After the 30-second timer has elapsed, the security system will automatically “ARM”. The  
siren/horn will chirp once and the parking lights will flash once.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
(continued)  
Automatic Arming: Lock and Arm  
(Additional programming required)  
Automatic Arming with Passive Door Locking  
The vehicle doors will automatically lock after the automatic arming cycle has been completed.  
Automatic Arming Bypass  
While the system is in disarmed mode, press the  
button twice. The horn/siren will respond  
with one chirp and the LED will turn “ON”. The security system will remain in this mode for as  
long as you wish. To exit this mode press the or buttons and the system will return to normal  
status.  
Disarming: Unlock and Disarm  
1. Press the button on the transmitter.  
2. The siren will chirp twice and parking lights will flash twice indicating that the system is now  
disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon  
disarming when interfaced with the security system.  
System Disarmed  
Door Triggered Trunk/Hood Triggered  
Shock Sensor  
Triggered  
Ignition Triggered  
Clear the Flash Icon:  
Press the “SET” button 3 times within 3 seconds will  
clear the flash icon on the LCD screen transmitter.  
IGN  
Tamper Disarming  
If the security system was triggered, upon disarm, the siren will chirp 4 times and parking lights  
will flash 3 times.  
Pathway Illumination  
(Must be Programmed On)  
This feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10 seconds  
upon the lock signal.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
(continued)  
Disarming: Unlock and Disarm  
Two Steps Door Unlock  
(Additional Wiring Required)  
This feature will independently unlock the drivers door only when disarming the security  
system. Pushing the button a second time within 3 seconds will unlock the other doors.  
Automatic Rearm  
(Must be Programmed On)  
If this feature is selected, the security system will automatically rearm itself within 60 seconds  
after disarming with the remote transmitter. Automatic rearm will cancel if any door is opened  
before the 60 second timer is up.  
Disarming without a Transmitter  
The override function may be used if the remote transmitter is lost or inoperative.  
1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will sound).  
2. Within 10 seconds push and release the valet switch, the alarm will stop sounding and enter  
the disarm mode. You can now start and operate the vehicle normally.  
(System in Disarm or Valet Mode)  
Remote Valet Mode  
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand  
your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all  
alarm functions and remote start functions are bypassed, however the remote panic feature and  
remote door locks will remain operational. To use the valet mode, the system must first be  
disarmed either by using your remote transmitter, or by operating the manual override sequence.  
Enter the Valet Mode:  
Remote Door  
Unlock  
1. While in disarmed mode, turn the ignition to “Off”  
position and open the drivers door.  
Remote Door  
Lock  
2. Push and hold the  
and  
buttons until the  
door locks cycle “Lock/Unlock”. The LED will will  
flash every 5 seconds while the unit is in the valet  
mode.  
Exit the Valet Mode:  
1. While in disarmed mode, turn the ignition to “Off” position and open the drivers door.  
2. Push and hold the and buttons until the door locks cycle “Lock/Unlock”.  
The LED will will be off indicating the alarm is out of the valet mode.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Progressive Remote Vehicle Locator System  
Note: The remote vehicle location system is active 30 seconds after the alarm is armed.  
1. Press the  
button to active the vehicle locator system. The horn/siren will beep 2 times and  
the parking lights will flash 3 times. This operation will repeat a second time.  
2. Press the button again within 30 seconds. The horn/siren will beep 3 times and the parking  
lights will flash 3 times. This operation will repeat a second time.  
3. Press the button again within 30 seconds. The horn/siren will beep 6 times and the parking  
lights will flash 6 times.  
Remote Panic Function  
The transmitter can be used as a remote panic switch to manually trigger the alarm system in case  
of an emergency.  
1. Press and hold the  
parking lights will begin to flash. The  
button for 3 seconds. The security system will begin to sound and the  
icon will display in the LCD transmitter display.  
2. During panic mode, the normal functions of this transmitter becomes temporarily inoperable.  
The transmitter and buttons can be used to lock and unlock the door (if the option is  
installed), however, once the button is pressed, the vehicle’s starter disable device, will be  
enabled allowing the vehicle to start.  
3. To stop the panic alarm, press the  
immediately.  
transmitter button , the panic mode will be turned off  
4. If the  
button is not pressed, the alarm will automatically stop after 30 seconds.  
Trigger the System  
When armed, your vehicle is protected as follows:  
1. Light impact will trigger the warn-away signal.  
2. Heavy impacts, doors open, hood open, trunk open or ignition key activated will trigger the  
programmed sequence. The starter disable relay prevents the vehicle’s starter from cranking.  
The siren, horn, parking lights and dome light will turn on to alert of an intrusion for 30  
seconds. If one of the sensors or detectors are still active, the security system will sound a  
maximum of 6 times for 30 seconds.  
Warn Away  
Triggered  
Shock Sensor  
Triggered  
Doors  
Triggered  
Trunk / Hood  
Triggered  
Ignition  
Triggered  
IGN  
ARM  
ARM  
ARM  
ARM  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(continued)  
Trigger the System  
LCD Transmitter Melody Sound  
When the Security System is triggered, it will alert the user with flashing icons on the LCD Display  
and audible melody sound. To stop the melody sound, press any button on the LCD transmitter.  
LCD Transmitter Clear the Flash Icon and Melody Sound  
When the Security System is triggered, the LCD screen will alert the user through melody sound  
and flashing icons. By pressing the “SET” button 3 times within 3 seconds it will clear the flashing  
icons and stop the melody sound.  
Noise Abatement  
The X11 security system has a built-in Noise Abatement Circuit that prevents annoying, repetitive  
false alarms by filtering out environmental conditions. If the security system is triggered more  
than five times by the same sensor , the circuit will interpret this as a false alarm and ignores, or  
bypasses that switch or sensor.  
The Noise Abatement Circuit monitors doors, hood and trunk switches differently. If the security  
system is triggered by one of these switches for three cycles, the switch will be bypassed until the  
trigger ceases.  
Anti-Car Jacking  
Warning: The anti-car jacking feature default setting is “OFF”. Have your installation facility enable  
this feature if you feel it is needed.  
Manual Anti-Car Jacking  
1. Press and hold the transmitter  
and  
buttons at the same time for 2 seconds while the  
vehicle’s ignition is “ON” and all doors are closed. The parking lights will turn on for 1.5  
seconds to indicate the anti-car jacking protection is armed.  
2. Once the system is armed, if you are forced from your vehicle, the system will trigger when the  
door is opened and closed while the ignition is “ON”.  
Passive Anti-Car Jacking  
1. Close all entrances first then turn the ignition switch to the “ON” position, the anti-car jacking  
system will arm.  
2. Once the system is armed, if you are forced from your vehicle, the system will trigger when the  
door is opened and closed while the ignition is “ON”.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(continued)  
Anti-Car Jacking  
Trigger the Anti-Car Jacking Mode  
Three Timer circuits will function as follows:  
First Timer Circuit  
1. 50 seconds after the car jacking mode has been activated, the siren will begin to sound for 15  
seconds.  
2. During the 15 second activation period, you will be alerted to push the valet switch once to  
turn off the car jacking feature.  
3. If by now the valet switch has not been pushed, it will enter the second timer circuit.  
Second Timer Circuit  
65 seconds after the system has been triggered, the siren starts sounding and the parking lights  
start flashing.  
Third Timer Circuit  
90 seconds after the security system has been triggered:  
1. The vehicles siren is still sounding, parking light are flashing  
2. The starter disable mode will activate to prevent the vehicle from starting  
3. It will remain active until the vehicles battery power is exhausted  
Override the System to Turn Off Anti-Car Jacking  
Turn the ignition switch from OFF to ON and within 10 seconds, push the valet switch. The siren  
will stop sounding and the security system is now disarmed.  
Status Checking (LCD Transmitter Only)  
System Check  
When you want to check the security systems present status through the transmitter LCD, press the  
transmitter “SET” button twice, within three seconds press the  
button. The security system  
responds with one melody sound and the LCD screen should be illuminated.  
Note: If there is no response from the LCD transmitter, you may be out of range to receive the  
signal.  
System Trigger Check  
Press the transmitter “SET” button first, within three seconds press the  
button. The transmitter will respond with one melody sound and all  
trigger records will immediately displayed on the transmitter LCD screen.  
IGN  
ARM  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Driver LCD Transmitter Paging  
It is useful in the event that someone wants to page the driver of the parked vehicle. (Optional)  
Inside the Vehicle Paging  
With the ignition switch in the "OFF" position, press the valet switch for 2 seconds to page the  
driver. One chirp will sound from the vehicle and the LCD transmitter will begin to sound with a  
melody. The  
icon will then appear on the LCD transmitter to confirm this function.  
Outside the Vehicle Paging  
(Optional and Requires Glass Mount Knock Sensor)  
To page the drive of the vehicle, "Knock" on the windshield glass to activate the LCD transmitter  
with a melody sound. The icon will then appear on the LCD screen (only when the optional  
knock sensor, Model # M10-Page, is installed).  
1. Turn on the vehicle paging sensor. Press the SET button on the LCD transmitter, within 3  
seconds, press the  
button to activate the driver paging sensor. The vehicle will then  
respond with chirps from the horn/siren and a melody sound from the LCD transmitter. The  
icon will then appear on the LCD transmitter screen.  
2. When the windshield knock sensor is activated, the vehicle will then respond with chirps from  
the horn/siren and a melody sound from the LCD transmitter. The  
the LCD transmitter screen.  
icon will then appear on  
3. When the driver of the vehicle unlocks the doors using the remote, the driver paging system  
will turn off.  
Dome Light Supervision  
The Security System has a unique feature which will control your vehicle’s dome light.  
1. Upon disarming the vehicle security system, the interior dome light will come on and remain  
remain on for thirty seconds.  
2. When the vehicle security system is triggered, the dome light will flash for the same duration  
as the horn/siren pulses.  
Ignition Controlled Door Locks  
If the vehicles door locks have been interfaced with the security system, the system will  
automatically lock the vehicle’s doors when the ignition key is turned to the “ON” position and or  
unlock the doors when ignition key is turned to the “OFF” position. The doors must be closed.  
Channel 3: Trunk Release Output  
Press and hold the  
button for 1.5 seconds to activate the trunk release (Channel 3 output)  
and/or any other devices connected.  
Channel 4 Output  
Press and hold the  
and  
button at the same time to activate the Channel 4 output.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel 5 Output  
Press and hold the  
and  
button at the same time to activate the Channel 5 output.  
button at the same time to activate the Channel 6 output.  
Channel 6 Output  
Press and hold the  
and  
Channel 7 Output: (Default Setting = Defrost Control)  
Press and hold the  
and  
button at the same time to activate the Channel 7 output.  
Note: If Channel 7 has been programmed for defrost operation it will not function from the transmitter.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Start Operation  
User Warnings  
As with any product that performs automatic functions, there are certain safety precautions that  
you must practice and be aware of.  
1. Keep the transmitter out of reach of children.  
2. DO NOT leave anyone in the vehicle while running on remote control.  
3. Alert any service personal that the vehicle can be started automatically.  
4. DO NOT start the vehicle by remote while it’s in an enclosed area or garage.  
5. Always apply the parking brake and lock the vehicle as you exit the vehicle.  
6. Should the unit malfunction, disconnect the fuse until the problem is corrected.  
7. The use and operations of this security system is the sole responsibility of the  
owner/operator of the vehicle.  
8. Some areas may have local ordinances that prohibit leaving a vehicle running on public  
streets. Check your local laws and ordinances.  
To Remote Start Your Vehicle by Using the Remote Transmitter  
1. Press the button twice on the remote transmitter.  
2. The parking lights will turn “ON” to indicate the remote start command has been received.  
3. The engine will start in approximately 5 seconds.  
4. Once the engine is running, the parking lights will turn back on to indicate climate controls are  
activated to your presettings (While the vehicle is running, the “minute” digits will appear  
flashing on the LCD screen of the transmitter. It will indicate the count down timer based on  
the 5, 10, 20 or 30 minute run time set up by your installation center).  
5. The vehicle will run for 5 to 30 minute cycles and automatically shut down (When the unit  
shuts off the count down timer will turn off and the transmitter will play a melody tune).  
Note: The Remote Start unit will not start if any of these conditions exist:  
1. The hood is opened.  
2. The brake pedal is pressed.  
3. Move the optional remote start enable toggle switch to “OFF” position (if installed).  
4. The gear selector is in any gear other than “Park” or “Neutral”.  
Safe Start  
The factory default setting to remote start your vehicle is to press the button twice. If the child  
(Child Safety Mode):  
safety mode has been activated, press the  
the vehicle.  
and the  
buttons at the same time to remote start  
To Operate the Vehicle While in the Remote Start Feature  
1. Insert the Ignition key, turn it to the “ON” position “NOT THE START POSITION”.  
2. Press the brake pedal.  
Note: If the Brake Pedal is pressed before the key is in the “ON” position, the engine will  
automatically shut off.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(continued)  
Remote Start Operation  
Quick Stop Feature  
This feature allows the vehicle to remain running after the key has been removed from the  
ignition. This feature is useful for occasions when you wish to exit and lock/arm the vehicle for  
short periods of time. This will keep the engine running for climate controls to stay on.  
1. Before turning the engine off with the ignition key, press the  
three times to indicate the feature is activated.  
button twice. The LED will flash  
2. Turn the ignition key to the “OFF” position (the engine will stay running).  
3. The engine will run until the pre-programmed run time elapsed or a shutdown input is  
received.  
Timer Starting Modes  
The X11 can be programmed to start and run the engine every 3, 2 or 1 hours by time or by  
temperature. The X11 can also be set to punctually start the engine at the same time the next day.  
In all modes, the engine will run for the pre-set time (Default setting is 10 minutes) running time  
and then shut down the same as if it were being controlled by the remote transmitter.  
Important! Timer starting should be used only in open areas. Never start, or most importantly  
leave a vehicle running in an enclosed area.  
3, 2 or 1 Hour Timer Start without Temperature Control: (Default Setting is 3 Hours)  
This feature is designed for extreme cold climate usage. The system will auto start the vehicle  
every three hours to prevent the engine from freezing and creating a hard-to-start condition.  
3, 2 or 1 Hour Temperature Starting Control: (Default Setting is 3 Hours)  
The system can be programmed to automatically start the vehicle’s engine whenever the  
temperature inside the vehicle reaches and/or drops below a preprogrammed temperature level.  
The X11 system will check the interior temperature ever 3,2 or 1 hour.  
Hourly Timer Start: (Runs Every 3, 2, or 1 Hours Depending on Programming)  
Press the button first, within three seconds press the  
button. The parking lights will flash  
six times and the siren/horn will sound six times. The vehicle is now in timer start mode.  
Note: The hourly timer start function requires additional programming of the LCD remote  
transmitter. (See Timer Setting page 20 for programming).  
Daily Timer Start:  
Press the button first, within three seconds press and hold the  
button for 3 seconds. The  
parking lights will flash six times and the siren/horn will sound six times. The vehicle is now  
programmed to start at the same time tomorrow (next day).  
Note: The daily timer start function requires additional programming of the LCD remote  
transmitter. (See Timer Setting page 20 for programming).  
Exit the Timer Start:  
To Cancel the timer start function, do one of the following:  
1. Start the vehicle manually using the ignition key.  
2. Remote start the vehicle using your remote transmitter.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turn Off Remote Start  
When the engine is running by remote start and you wish to stop the engine from running:  
1. Press the  
button twice on the remote transmitter.  
2. Move the optional remote start toggle switch to the “OFF” position (if installed).  
3. Press the vehicle’s brake pedal, the engine will stop running and the parking lights turn off to  
indicate the engine has stopped.  
Shut Down Input for Remote Starter  
If any of the following conditions exist while the system is operating, the engine will not start or will  
shut down immediately:  
1. The hood is opened.  
2. The brake pedal is pressed.  
3. The hand brake is released (for Standard Transmission vehicles only).  
4. Engine is over-RPM (Tachometer Checking Type only).  
5. The preprogrammed run time (5/10/20/30 minutes) has elapsed.  
6. Press the  
button twice on the remote transmitter under Remote Start Mode.  
7. Move the optional remote start enable toggle switch to “OFF” position (if installed).  
8. The vehicle refused to start running after 3 unsuccessful attempts.  
(Also See Installation Manual)  
Turbo Timer Mode  
Turbo Timer Mode keeps the engine running after arriving at you destination for a programmable  
time period of 3, 5 or 10 minutes. This allows the system’s time to conveniently cool down the  
turbo charger after you have left the vehicle.  
To Activate:  
1. While the engine is running, set the emergency brake and place the transmission to "Park".  
2. Before turning off the engine, press and release  
and  
buttons at the same time. The light  
will flash to indicate the remote start has entered Turbo Timer Mode.  
3. Remove the ignition key from the key cylinder. The engine will keep running.  
4. Exit and secure the vehicle. The engine continues running until the preprogrammed time has  
elapsed.  
Interference  
Note: The transmission range may become shorter if the system is interfered by a stronger radio  
frequency from sources of high voltage electric power or obstacles like tall buildings. The  
transmitter uses low output powered frequency.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote LCD Icons  
Hidden Alarm Mode  
Your vehicle is in armed with  
hidden alarm mode  
Armed Mode  
Vehicle is in armed mode  
Valet Mode  
All the function shall be  
temporarily on hold  
Car Jack Mode  
Car jacking mode is activated  
Remote Transmission  
You are transmitting the signal to  
the control unit  
In-Range Indicator  
You are within the remote  
control range  
Sensor Trigger  
Trigger on sensor 1 (zone 4) or  
optional sensor 2 (zone 6)  
Hood Trigger  
Hood is illegally opened (Zone 1)  
Warn Away Trigger  
Warn away trigger on sensor 1  
or optional sensor 2  
Trunk Trigger  
Trunk is illegally opened (Zone 2)  
Door Open Warning  
Doors are illegally opened  
(Zone 3)  
Low Battery  
You have to replace the remote  
controls battery  
Ignition Trigger  
Ignition switch is illegally turned  
on (Zone 5)  
Engine Running  
Your vehicle’s engine is running  
Alarm Alert  
You have set morning  
alarm call  
System Trigger  
Engine Cranking  
Your vehicle’s engine is cranking  
by remote control  
Power Save Mode  
Saves the battery power  
Timer Control Start  
Engine start automatically at the  
same time next day or 2/3 hours.  
Vibration Mode  
Remote control vibrates when  
the system is triggered  
Driver Paging  
Someone is paging you in front  
of your vehicle  
Time Monitor  
Count Down Timer  
Reminder when time  
is up for parking  
Channel #3 is Activated  
Channel #4 is Activated  
Melody Mode  
Remote control alert user  
through melody sound  
Channel #5 is Activated  
Channel #6 is Activated  
Channel #7 is Activated  
Button Lock  
Disable the transmission  
function temporarily  
Temperature Monitor  
Indoor temperature of your  
vehicle  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming the LCD Transmitter  
Button  
Description  
Operation  
LCD Screen Lamp Turns ON for  
Five Seconds  
Press and Hold for 1 Second  
1 Melody Sounds to Confirm  
SET  
Press and Hold for 3 Seconds  
2 Melody Sounds to Confirm  
Timer Programming Mode  
Power Save Mode  
SET  
Press and Hold for 5 Seconds  
1 Melody Sounds to Confirm  
SET  
SET (3X)  
Clear the Flash Icon and Melody Sound Press within 3 Seconds  
on the LCD Screen  
SET & LOCK  
Button Lock Enabled/Disabled  
Press within 3 Seconds  
Press within 3 Seconds  
SET & UNLOCK Melody/Vibrate Mode  
Program Count Down Timer  
Press within 3 Second Cycles  
Leave the Buttons Starting Count  
Down then Timer Icon Flashes  
+
SET  
(10 m, 20 m, 30 m, 1 hr, 1.5 hr, 2 hr)  
Enable/Disable Beep Sound While  
Pressing Button  
+
SET  
Press for 2 Seconds  
Display Illumination On/Off  
3 Seconds between “SET - SET”  
SET - SET -  
and Hold  
for 2 Seconds  
Switch Between 1st Car RF Control and  
2nd Car RF Control  
+
+
SET -  
Hold  
for 2 Seconds  
Screen Lamp On  
Press and hold the “SET” button one second, with the melody sound and the LCD screen lamp  
will turn on for 5 seconds.  
Power Save Mode  
While in the Power Save Mode, the LCD transmitter uses “0” current to save the battery power.  
1. Press and hold the “SET” button for 5 seconds. One melody will sound from the transmitter  
and the LCD will show “SAVE”. You are now in the Power Save Mode.  
2. Under the Active Arming Mode and Disarm Mode. Turn the ignition switch to the “ON” position.  
The LCD remote transmitter will automatically enter the Power Save Mode.  
Exit Power Save Mode  
Press any button on the LCD transmitter to exit the Power Save Mode.  
Clear the Flash Icon and Melody Sound  
Press the SET button 3 times within 3 seconds and it will clear the flashing icon and melody  
sound on the LCD transmitter.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming of the LCD Transmitter  
Stop the Trigger Melody  
While triggering the alarm, the LCD screen will alert the user through melody sound and flashing  
trigger icon. Press any button on the transmitter to stop melody sound only.  
Button Lock  
Use this mode to disable the transmission function of the remote control temporarily to prevent  
any inadvertent pressing of buttons.  
1. Press the “SET” button first, within 3 seconds press and hold the  
button for 2 seconds to  
activate or cancel the button lock function. The  
to show button lock mode.  
icon will be displayed on the LCD screen  
Vibration/Melody Mode  
This mode is useful when you are in a noisy place and it is difficult to hear the beep from the  
remote. The LCD transmitter will vibrate if your security system has been activated.  
Press the “SET” button first, within 3 seconds press the  
(
) button for 2 seconds to select  
the mode of vibrate/melody. The  
icon will be displayed on the LCD screen to show mode.  
Set-Up Fixed Count Down Timer  
Press the “SET” button first, then within 3 seconds press and hold the  
The LCD screen will show the icon and timer (0:10). Press the  
desired time.  
button for 2 seconds.  
button again to choose the  
Note: 1. The countdown periods are fixed at 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5  
hours and 2 hours maximum.  
Note: 2. Press the SET button for a real time indication of the remaining time left.  
Note: 3. When the display is showing 0:00, the timer is off  
Out of Range Indication  
1. If the transmitter is within range, the  
icon will display on the LCD screen.  
2. If you are out of range, the  
times.  
icon will disappear from LCD Screen and transmitter will beep 5  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Clock and Timer Setting  
Step  
Button  
Description  
Operation  
Press and Hold SET  
Button for 3 Seconds  
Time Setting (Hour)  
Flash Digit for Adjusting  
1
for (-) and (+)  
Press the SET  
Button Once  
Time Setting (Min.)  
Flash Digit for Adjusting  
for (-) and (+)  
for (-) and (+)  
for (-) and (+)  
for (-) and (+)  
2
3
4
5
Press the SET  
Button Once  
Alert Alarm Time Setting (Hour) Flash  
Digit for Adjusting  
Press the SET  
Button Once  
Alert Alarm Time Setting (Min.) Flash  
Digit for Adjusting  
Press the SET  
Button Once  
Alert Alarm Setting ON/OFF  
Count Down Timer Setting (Hour) Flash  
Digit for Adjusting  
Press the SET  
Button Once  
6
for (-) and (+)  
(Max 19 Hrs. 59 Min.)  
Press the SET  
Button Once  
Count Down Timer Setting (Min.) Flash  
Digit for Adjusting  
7
8
for (-) and (+)  
Press the SET  
Button Once  
Count Down Timer Setting ON/OFF  
for (OFF) and (ON)  
Press and Hold  
Button for 2 Seconds Flash  
Daily Timer Start Timer Setting  
10  
for (-) and (+)  
/
Icon and Hours for Adjusting  
Note: Any adjustment requires starting at the beginning (Step 1) and following the steps until you  
reach the one that corresponds with the description/function you want to program.  
For instance, if you are trying to set the Alert Alarm Setting ON/OFF (the description that  
corresponds with Step 5) you must follow steps 1-5 in order for it to be set.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts  
TRANSMITTERS  
DESCRIPTION  
MODEL #  
PRICE  
5-Button Transmitter for  
X11 Security System  
X11RF-LCD  
$139.95 ea.  
4-Button Transmitter for  
X11 Security System  
X11RF  
59.95 ea.  
BATTERIES  
**1.5 Volt AAA Lithium Battery Highly  
Recommended  
*1.5 Volt AAA High Capacity Digital  
Camera Battery Suggested  
1.5 Volt AAA Alkaline Battery Minimum  
CR2032 - 3 Volt Lithium Battery (2 pcs.)  
Models:  
Radio Shack: #23-162  
Duracell: #DL2032  
Eveready: #ECR2032  
Panasonic: # CR2032  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts Order Form  
Mail to: Magnadyne Corporation  
ATTN: Consumer Parts Sales  
P.O. Box 5365  
Credit Card or Money Order Only  
(Sorry No Cash, C.O.D. or personal checks accepted)  
Call: (310) 884-7777 Fax: (310) 637-9542  
Carson, CA 90749-5365  
SHIP TO: (No P.O. Boxes)  
LAST NAME  
FIRST NAME  
INITIAL  
STREET ADDRESS  
ADDITIONAL ADDRESS  
ADDITIONAL ADDRESS  
CITY  
STATE  
ZIP CODE  
DAY TIME PHONE NUMBER  
CREDIT CARD INFORMATION  
VISA  
MC  
CREDIT CARD N0.  
CARD HOLDER’S LAST NAME  
STREET ADDRESS  
CITY  
EXPIRATION DATE  
FIRST NAME  
INITIAL  
STATE  
QTY.  
ZIP CODE  
PART #  
DESCRIPTION  
PRICE EACH  
TOTAL  
Shipping and Handling  
Sales Subtotal = ________ . ______  
Up to $20.00  
20.01 to 30.00  
30.01 to 45.00  
45.01 to 70.00  
Over 70.01  
$5.00  
5.95  
6.50  
6.95  
7.95  
California Residents Add Sales Tax = ________ . ______  
Shipping and Handling (See Chart) = ________ . ______  
TOTAL = ________ . ______  
On regular orders please allow 4-5 weeks for delivery.  
Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.  
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Lifetime Warranty  
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original  
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the  
option of the Magnadyne Corporation or its authorized agents, if said product or part is found  
defective in materials or workmanship, when properly connected and operating on the correct  
power requirements designated for the specific product. This warranty and Magnadyne Corporation  
or its authorized agents obligations, hereunder do not apply where the product was: damaged while  
in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably  
maintained, utilized in commercial or industrial operation, or serviced by anyone other than  
Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken  
or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its  
authorized agents do not assume any labor costs for the removal and reinstallation of any product  
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized  
agents. Such costs are the sole responsibility of the purchaser.  
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories  
used in connection with the product resulting from improper installation, alteration, accident,  
misuse, abuse or acts of nature.  
This Limited Life Time Warranty applies only to the receiver section of the security system. Neither  
the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile  
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness  
or any accessory item are covered by our standard 12 month limited warranty.  
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential  
or incidental damages or claims that may arise due to failure of product to operate properly  
except those accorded by law. Magnadyne's or its authorized agents liability to the repair,  
replacement of the product as stated above if all conditions of the warranty are met. No  
expressed warranty or implied warranty is given except those set forth herein. Magnadyne does  
not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or  
against the loss or damage to the contents of any vehicle in which a security system is installed.  
Magnadyne security systems are only a deterrent against possible theft.  
This warranty extends only to the original purchaser of the product and for the vehicle in which it  
was originally installed. This warranty is not transferable or assignable to any person or vehicle.  
Defective merchandise should be returned to the original point of purchase or secondly to  
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must  
be obtained before sending, or merchandise may be refused.  
X11-UM 3-5-08 Rev. A  
© Copyright 2008 Magnadyne Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lennox Hearth Indoor Fireplace X FIRES WS LP User Manual
Lenovo Laptop 276583U User Manual
Lenovo Personal Computer 10093 User Manual
LG Electronics Cell Phone 3350232 User Manual
LG Electronics TV DVD Combo 2640 User Manual
Makita Sander GV7000C User Manual
Marantz Home Theater System SR6005 User Manual
Marshall Amplification Musical Instrument Amplifier Echohead User Manual
Maytag Microwave Oven 11 06 00 User Manual
Mellerware Iron 23600a User Manual