Magellan GPS Receiver 860T User Manual
®
™
Magellan RoadMate  
Reference Manual  
Instructions for Operating the  
Magellan RoadMate 860T  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About the AC Adapter  
•
•
Do not use the adapter in a high moisture environment. Never touch the adapter when your hands or feet are wet.  
Allow adequate ventilation around the adapter when using it to operate the device or charging the battery. Do not cover  
the AC adapter with paper or other objects that will reduce cooling. Do not use the AC adapter while it is inside a  
carrying case.  
•
Connect the adapter to a proper power source. The voltage and grounding requirements are found on the product case  
and/or packaging.  
•
•
Do not use the adapter if the cord becomes damaged.  
Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to  
excess moisture.  
About the Battery  
•
•
Use the charger approved for / provided with your Magellan RoadMate 860T.  
Do not mutilate, puncture, or dispose of the battery in fire. The battery can burst or explode, releasing hazardous  
chemicals.  
•
•
Important instructions (for service personnel only)  
Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the  
instructions.  
•
•
•
Replace only with the same or equivalent type recommended by Magellan.  
The battery must be recycled or disposed of properly.  
Use the battery only in the specified equipment.  
About the Headphones  
•
•
Prolonged listening to music using the supplied headphones at maximum volume level can cause damage to your ears.  
Laws in some states prohibit wearing stereo headphones while operating a motor vehicle. Please contact your state’s  
Department of Motor Vehicles for information.  
(2)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTRUCTION TO THE USER  
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee  
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
•
•
•
•
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with  
non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is  
cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's  
authority to operate this equipment.  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.  
© 2006 Thales Navigation, Inc. All rights reserved. The Magellan Logo, Magellan, Magellan RoadMate, Turn it on and go,  
TrueView, QuickSpell, SmartDetour, TrueFix, and SmartVolume are trademarks of Thales Navigation. No part of this user  
manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying  
and recording, for any purpose other than the purchaser’s personal use, without the prior written permission of Thales  
Navigation.  
631330-01 A  
(3)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Magellan® RoadMate™ ...............................................................................................................................(1)  
Instructions for Operating the Magellan RoadMate 860T................................................................................(1)  
About Charging the Magellan RoadMate 860T ........................................................................................................(1)  
IMPORTANT SAFETY WARNINGS ......................................................................................................................(1)  
About the AC Adapter .......................................................................................................................................(2)  
About the Battery .............................................................................................................................................(2)  
About the Headphones ......................................................................................................................................(2)  
INSTRUCTION TO THE USER ................................................................................................................................(3)  
Contact Information .........................................................................................................................................(4)  
Technical Support ............................................................................................................................................(4)  
Warranty Service .............................................................................................................................................(4)  
Customer Service .............................................................................................................................................(4)  
Registration ...................................................................................................................................................(4)  
Chapter 1: Information ......................................................................................................................................1  
About Satellite Navigation ..............................................................................................................................................................1  
How Satellite Navigation Works ......................................................................................................................................................1  
Line of Sight ............................................................................................................................................................................... 1  
A Word on the Safe Usage of GPS Maps ..........................................................................................................................................2  
From Source to Destination ......................................................................................................................................................... 2  
Placement of Your GPS Receiver for Optimal Satellite Reception ....................................................................................................2  
Signal Acquisition Time ..................................................................................................................................................................2  
GPS Maps and Your Safety .............................................................................................................................................................3  
Chapter2: Magellan RoadMate ..........................................................................................................................4  
Front View .......................................................................................................................................................................................4  
Rear View .......................................................................................................................................................................................5  
Top View .........................................................................................................................................................................................5  
Bottom View ...................................................................................................................................................................................6  
Left Side View .................................................................................................................................................................................6  
Right Side View ..............................................................................................................................................................................7  
Enhanced Cradle - Back View .........................................................................................................................................................7  
Using Removable Storage Cards ....................................................................................................................................................8  
To Insert the Storage Card: ......................................................................................................................................................... 8  
To Remove the Storage card: ...................................................................................................................................................... 8  
Battery Removal and Installation ...................................................................................................................................................8  
Removing the Battery ................................................................................................................................................................. 8  
Installing the Battery .................................................................................................................................................................. 9  
Chapter 3: Vehicle Installation ........................................................................................................................10  
Installing the Windshield Mount ...................................................................................................................................................10  
Chapter 4: Antenna Position ...........................................................................................................................13  
Chapter 5: Navigation Basic Operation ...........................................................................................................14  
Turning the Magellan RoadMate On Out of the Box ......................................................................................................................14  
Suspend Power or “Sleep” Mode ............................................................................................................................................... 14  
Power Management .................................................................................................................................................................. 14  
Resetting the Magellan RoadMate ................................................................................................................................................14  
Adjusting the Volume ...................................................................................................................................................................14  
Repeating the Last Command ......................................................................................................................................................14  
Making Selections ........................................................................................................................................................................14  
Inputting Text Characters .............................................................................................................................................................15  
Additional Characters (“More” Button) .........................................................................................................................................15  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Numerical Characters (“123” Button) ..........................................................................................................................................15  
What Is QuickSpell? ......................................................................................................................................................................16  
Multi-Word Indexing .....................................................................................................................................................................17  
Chapter 6: Traveling .......................................................................................................................................18  
Guidance Information Screens ......................................................................................................................................................18  
Map Screen ...................................................................................................................................................................................19  
Changing from 2D to 3D Map View ...............................................................................................................................................19  
Changing the Map Zoom Levels.....................................................................................................................................................20  
Maneuver List Screen ....................................................................................................................................................................20  
TrueView 3D Screen .......................................................................................................................................................................21  
Choosing the Route Method...........................................................................................................................................................22  
Changing the Route Method ..........................................................................................................................................................22  
Cancelling a Planned Route ..........................................................................................................................................................22  
Detouring from the Planned Route.................................................................................................................................................23  
Excluding a Maneuver in the Planned Route..................................................................................................................................23  
Displaying Information About Your Present Location .....................................................................................................................24  
Saving Your Current Location to Your Address Book ......................................................................................................................24  
Finding POIs Along Your Route ......................................................................................................................................................24  
Finding a Detour Along Your Route ................................................................................................................................................25  
Chapter 7: Selecting Destinations........................................................................................................................................... 27  
Destination Screen ........................................................................................................................................................................27  
Country Selection (Globe Button)...................................................................................................................................................27  
Entering and Routing to Your Home Address ................................................................................................................................27  
Selecting a Destination Using Select Address ..............................................................................................................................28  
Search By City .......................................................................................................................................................................... 29  
Search by Zip Code ................................................................................................................................................................... 29  
Search By State ........................................................................................................................................................................ 30  
Previous City ............................................................................................................................................................................. 31  
Selecting a Destination Using the Address Book ..........................................................................................................................32  
Previous Destinations ............................................................................................................................................................... 32  
Favorites ................................................................................................................................................................................... 34  
List Addresses .......................................................................................................................................................................... 36  
Create New Entry ...................................................................................................................................................................... 37  
Trip Planner .............................................................................................................................................................................. 41  
Selecting a Point of Interest as a Destination ...............................................................................................................................47  
Spell Name ............................................................................................................................................................................... 47  
Select Category.......................................................................................................................................................................... 49  
Custom POIs ............................................................................................................................................................................. 51  
Selecting an Intersection as a Destination ...................................................................................................................................52  
Search by City ........................................................................................................................................................................... 52  
Search by Zip Code ................................................................................................................................................................... 53  
Search by State ........................................................................................................................................................................ 54  
Previous City ............................................................................................................................................................................. 54  
Chapter 8: Navigation Options ........................................................................................................................55  
Configuration ...............................................................................................................................................................................55  
POI Selection ............................................................................................................................................................................ 55  
Custom POIs ............................................................................................................................................................................. 55  
Map Options ............................................................................................................................................................................. 60  
TrueView Options ...................................................................................................................................................................... 60  
Select Map Color ....................................................................................................................................................................... 60  
Route Preferences..................................................................................................................................................................... 61  
Detour Options .......................................................................................................................................................................... 62  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Voice Options ............................................................................................................................................................................ 63  
Menu Colors .............................................................................................................................................................................. 63  
Tone Options ............................................................................................................................................................................. 64  
GPS Options .............................................................................................................................................................................. 64  
Simulator Mode ........................................................................................................................................................................ 65  
Map Regions ............................................................................................................................................................................. 65  
Automatic Volume .................................................................................................................................................................... 67  
TMC Options ............................................................................................................................................................................. 67  
\Backup and Restore ................................................................................................................................................................ 67  
Clear Address Book ................................................................................................................................................................... 68  
Map Information ....................................................................................................................................................................... 69  
Trip Computer ...............................................................................................................................................................................69  
Current Trip .............................................................................................................................................................................. 69  
Chapter 9: System Settings .............................................................................................................................72  
Brightness ....................................................................................................................................................................................72  
Power Management ......................................................................................................................................................................72  
Password ......................................................................................................................................................................................72  
Set Password ............................................................................................................................................................................ 72  
Remove Password ..................................................................................................................................................................... 73  
Language .....................................................................................................................................................................................73  
Chapter 10: System Status .............................................................................................................................74  
Product Information ......................................................................................................................................................................74  
User Storage .................................................................................................................................................................................74  
Diagnostics ..................................................................................................................................................................................74  
Audio Test ................................................................................................................................................................................. 74  
Touchscreen Test 7...................................................................................................................................................................... 4  
Keypad Test .............................................................................................................................................................................. 74  
Video Test ................................................................................................................................................................................. 74  
Chapter 11: Help .............................................................................................................................................75  
Quick Tips .....................................................................................................................................................................................75  
Contact Us ....................................................................................................................................................................................75  
Chapter 12: Magellan RoadMate Tools Installation .........................................................................................76  
Installing the Software .................................................................................................................................................................76  
Connecting Your Magellan RoadMate ...........................................................................................................................................76  
Chapter 13: Magellan RoadMate POI Manager ................................................................................................77  
Latitude ........................................................................................................................................................................................77  
Longitude .....................................................................................................................................................................................77  
Altitude .........................................................................................................................................................................................78  
Opening a POI File ........................................................................................................................................................................79  
Creating a New POI FIle ................................................................................................................................................................79  
Adding Individual POI’s ................................................................................................................................................................79  
Importing a Data FIle ....................................................................................................................................................................81  
Chapter 14: Magellan RoadMate Music Manager ............................................................................................82  
Chapter 15: Music Player ................................................................................................................................83  
Single Song Play ...........................................................................................................................................................................83  
Multiple Song Play ........................................................................................................................................................................83  
Play .......................................................................................................................................................................................... 84  
Create ....................................................................................................................................................................................... 84  
Modify ....................................................................................................................................................................................... 84  
Delete ....................................................................................................................................................................................... 84  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Rename .................................................................................................................................................................................... 85  
Play Mode .....................................................................................................................................................................................85  
List Songs .....................................................................................................................................................................................85  
Equalizer ......................................................................................................................................................................................86  
Help ..............................................................................................................................................................................................86  
Chapter 16: Magellan RoadMate Photo Manager ............................................................................................87  
Chapter 17: Photo Viewer................................................................................................................................ 88  
View Single Photo .........................................................................................................................................................................88  
Previous Image (left arrow) ..................................................................................................................................................... 88  
Zoom ....................................................................................................................................................................................... 88  
Slideshow ................................................................................................................................................................................ 89  
Pan .......................................................................................................................................................................................... 89  
Rotate Image ........................................................................................................................................................................... 89  
Next Image (right arrow) .......................................................................................................................................................... 89  
ESC .......................................................................................................................................................................................... 89  
Manage Photos .............................................................................................................................................................................89  
List View ................................................................................................................................................................................... 89  
Thumbnail ................................................................................................................................................................................ 89  
Rename .................................................................................................................................................................................... 89  
Properties ................................................................................................................................................................................. 90  
Tools............................................................................................................................................................................................. 90  
Preferences ............................................................................................................................................................................... 90  
Transfer Photos ........................................................................................................................................................................ 90  
Delete Files ............................................................................................................................................................................... 90  
About ........................................................................................................................................................................................ 90  
Appendix .........................................................................................................................................................91  
POI Categories ..............................................................................................................................................................................91  
PC Requirements ..........................................................................................................................................................................92  
GPS Status Screen ........................................................................................................................................................................93  
Frequently Asked Questions ..........................................................................................................................................................97  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contact Information  
If you need support for your Magellan RoadMate and you wish to contact Thales, please use the following information to  
direct your questions/comments to the proper person.  
1.1 Technical Support  
If you need technical assistance or “how-to” help, or if you have a technical question about the functionality of your  
Magellan product, please contact us on the Internet at www.magellangps.com or reach us by fax or by phone.  
Our Technical Support phone representatives are available Monday through Friday, 6:00 a.m. to 5:00 p.m. PST/PDT. After  
hours, you may leave a detailed voice mail message that will be returned within the next business day.  
Telephone: (866) 868-2259 or (909) 394-5000 (Outside North America)  
You may also reach Technical Support by Fax: (909) 494-7777 [Attn: Tech. Support]; or E-Mail:  
magellansupport@thalesnavigation.com  
1.2 Warranty Service  
To obtain warranty service on your unit, you must contact us for a return authorization (RA) before you ship the product.  
Packages arriving at our dock without an RA will be refused.  
To obtain an RA, simply contact our Technical Support group at: Telephone: (866) 868-2259 or (909) 394-5000; Fax:  
(909) 494-7777 [Attn: Tech. Support]; or E-Mail: magellansupport@thalesnavigation.com  
1.3 Customer Service  
If you need to order accessories or obtain unlock codes, you can call our Customer Service Department Monday through  
Friday, 6:00 a.m. to 5:00 p.m. PST/PDT, or visit our Web site at www.magellangps.com.  
Telephone: (866) 339-0488 or (909) 394-5000 (Outside North America); Fax: (909) 394-7078.  
1.4 Registration  
Please make sure to register your Magellan RoadMate at www.magellangps.com. By registering, you will be informed of the  
latest product updates.  
(4)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: Information  
1.1 About Satellite Navigation  
Global satellite navigation is an exciting technology, providing enhanced productivity and accuracy in a vast number of  
industries. It adds a new level of enjoyment and safety to a wide range of navigation, sports, and recreational activities.  
A Global Navigation Satellite System (GNSS) is a network of satellites that transmit high-frequency radio signals containing  
time and distance data that can be picked up by a receiver, allowing users to pinpoint their precise locations anywhere  
around the globe.  
There are two Global Navigation Satellite Systems in operation: the U.S. Global Positioning System (GPS) and the Russian  
GLObal NAvigation Satellite System (GLONASS). These systems are constantly being upgraded to meet higher standards of  
reliability. A third GNSS named GALILEO, after the Italian astronomer of the early 1600s, is being developed in Europe  
specifically to provide a higher standard of integrity and reliability, required to ensure the safety of lives during transport by  
air, land and sea, without the use of additional augmentation systems.  
While the GPS and GLONASS satellite networks are being developed to achieve maximum performance, Satellite-Based  
Augmentation Systems (SBAS) have been established to provide improved accuracy. SBAS provides differential signal  
corrections for GPS and GLONASS transmissions with the use of ground stations and geostationary satellites in specific  
regions. This is GNSS-1, the first phase in establishing the required integrity for high-precision satellite navigation.  
GNSS-2 requires the launching of new satellites into orbit and a complete upgrade of the existing satellite systems. This  
second phase is already well underway. GALILEO, scheduled to begin service in 2008, is being developed to meet the  
standards of GNSS-2 for rapid and reliable, certified precision positioning.  
1.2 How Satellite Navigation Works  
Global navigation satellites continuously transmit time and distance information as they orbit Earth in a precise formation.  
Navigation satellite receivers use this information to calculate an exact location through triangulation. Every point on Earth is  
identified by two sets of numbers called coordinates. These coordinates represent the exact point where a horizontal line,  
known as latitude, crosses a vertical line, known as longitude. The receiver locks on to at least three satellites and uses the  
information received to determine the coordinates of the receiving device.  
By comparing the time the signals were transmitted from the satellites and the time they were recorded, the receiver  
calculates how far away each satellite is. The distance of the receiver from three or more satellites reveals its position on the  
surface of the planet. With these distance measurements, the receiver might also calculate speed, bearing, trip time,  
distance to destination, altitude, and more.  
The satellite-navigation device may display its position as longitude/latitude, Universal Transverse Mercator (UTM), Military  
Grid (MG), or simply as a point on an electronic map. Many Thales Navigation receivers provide comprehensive mapping  
data, making satellite navigation an easy tool to enhance your recreational and industrial activities.  
1.2.1 Line of Sight  
Satellite-navigation receivers operate by line of sight with global-positioning satellites. This means that at least three  
satellites must be in “view” of a receiver in order to calculate longitude and latitude. A fourth satellite must also be within  
line of sight to calculate altitude. On average, eight satellites are continuously within line of sight of every position on Earth;  
the more satellites in view, the more accurate the positioning.  
Though the radio signals of navigation satellites will pass through clouds, glass, plastic, and other lightweight materials,  
satellite-navigation receivers will not work underground or in other enclosed spaces.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: Information  
1.3 A Word on the Safe Usage of GPS Maps  
Just like paper maps, maps on GPS devices vary greatly in terms of information included and visual presentation. Whether  
topographical maps, roadmaps or marine charts, each map and the data it presents is designed for a specific purpose. For  
example, marine charts will often present only a minimal representation of roadways and are not a substitute for street maps.  
Topographic maps usually provide minimal detail about bodies of water and do not contain marine navigational markers.  
Maps also vary widely in scale: the smaller the scale, the more detailed the map. Therefore, when using GPS maps (just as  
with paper maps) it is important to consider what type of map you are using in your explorations and to use common sense.  
1.3.1 From Source to Destination  
Thales Navigation, maker of Magellan GPS products, is not a cartography company. We do not create the maps that are used  
on our GPS devices. We seek to acquire map data from the best public and private sources available at the time of  
publication. Thales Navigation licenses* topographical maps, roadmaps, marine charts and points of interest (POI) data  
from commercial and governmental cartographic sources that provide raw map data. Thales Navigation processes and  
compresses the raw data into a format that makes it presentable and manageable to work on our GPS devices. And to ensure  
that our map data is as robust as possible, data from multiple sources are often combined to provide a better user experience  
for our customers. This processing does not alter the landforms, coordinates or other spatial data that comes in the raw data.  
The accuracy of the maps is fundamentally dependent on the source data used to create them. Map data changes frequently  
due to both natural and man-made causes. As a result, governmental and commercial cartography companies must  
continuously review, correct, and improve upon their map data. We release new versions of our maps on a regular basis to  
reflect these changes.  
After processing the data, we test the compatibility of the map with our GPS devices to ensure that the products we release  
work properly on our GPS devices. We also beta-test our products to get customer feedback prior to release.  
1.4 Placement of Your GPS Receiver for Optimal Satellite Reception  
FIrstly, before considering signal reception, it is important to understand that your GPS receiver is a sensitive piece of  
equipment. You should never place it in an area of your vehicle where it may be struck by other items, or where vibration  
may cause it to strike other items or parts of the vehicle. The windshield mount included in the box allows you to place the  
receiver in such a way that the antenna can receive the satellite signal through the windshield without being obstructed by  
other parts of the vehicle. However, tinted windows or other reflective coatings may interfere with reception. In this case, it  
may be required to attach an external antenna (optional). An external antenna provides faster satellite fix times and greater  
signal strength. Because it is mounted outside of the vehicle, it is not affected by reflective coatings on windows and has an  
unobstructed line of sight to the satellites. Other mounting solutions are available but may require an external antenna.  
External conditions also affect GPS signal reception. Although weather conditions do not affect the signal, tall buildings and  
trees, driving through canyons, wooded areas, or tunnels, and sitting in a garage or covered parking area will affect the GPS  
signal. The GPS receiver constantly monitors and updated the GPS signal status and will reacquire the signal once it is clear  
of any obstructions.  
1.5 Signal Acquisition Time  
The first time you use your Magellan RoadMate, or if you travel over 500 miles with the unit off, there may be a delay in  
receiving the initial satellite fix; depending on your position and the position of the satellites, this could take 15 minutes or  
more. Normal usage will receive the satellite fix much faster, but still may take several minutes. It is important to have your  
antenna rotated upward and an unobstructed view of the sky to receive the best possible satellite signal.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: Information  
1.6 GPS Maps and Your Safety  
Remember, your GPS device is an aid to navigation. It must be used with common sense, and it is important that users  
interpret GPS map data with a critical eye. Landscapes and roads change or may be impassable, trees and tall buildings can  
obscure GPS signals, and your GPS device may not always reflect the complete picture. When using GPS, you must combine  
the information provided by your GPS map with your relevant local knowledge, road signage, buoys, depth soundings and  
changing local conditions to generate a complete understanding of your situation.  
It is your responsibility to ensure compliance to all traffic laws, including pedestrian observance of crosswalks, and to use  
good judgment while operating the Magellan GPS receiver. Safety must be your primary concern. The Magellan GPS receiver  
must not be used while engaged in any activity requiring the user's full attention to the environment. For instance, the  
Magellan RoadMate GPS receiver should be operated only by vehicle passengers or by the driver when the vehicle has come  
to a complete stop. The driver must not attempt to view the display while driving. Disregard any unsafe, hazardous or illegal  
route suggestions.  
Magellan maps do not include, analyze, process, consider or reflect any of the following: legal restrictions (such as weight,  
height, width, load and speed restrictions); road slope or grade; bridge height, width, weight or other limits; population  
density; neighborhood quality or safety; availability or proximity of law enforcement, emergency rescue, medical or other  
assistance; construction work zones or hazards; road, sidewalk, or waterway closures or conditions; weather conditions;  
pavement characteristics or conditions; special events; traffic congestion; time of day.  
*Thales Navigation licenses map data from governmental sources such as, but not limited to, U.S. Geological Survey  
(USGS), the National Oceanic and Atmospheric Administration (NOAA-NOS) and the Canadian Hydrographic Service (CHS).  
Thales Navigation also licenses map data from commercial cartography companies such as Navigation Technologies,  
Navionics, DMTI and C-Map.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Magellan RoadMate  
2.1 Front View  
1
2
Suspend Button  
Press to enable “sleep” mode.  
While viewing the map, press to zoom in on the center of the display.  
The Zoom In Button can also be used with long lists to scroll one page  
at a time.  
Zoom In Button  
3
4
Menu Button  
Enter Button  
Press to view Main Menu.  
Press to confirm highlighted selections.  
Light turns green when battery is fully charged, orange while battery is  
charging.  
5
6
7
Power Indicator  
Zoom Out Button  
Locate Button  
While viewing the map, press to zoom out from the center of the  
display. The Zoom Out Button can also be used with long lists to scroll  
one page at a time.  
Press to display current location details and save it to your address  
book.  
8
9
Escape Button  
Mute Speaker  
View Button  
Press to stop the current function.  
Press to disable sound from the speaker and the headphone jack.  
Press to view map display, maneuver list or TrueView 3D display.  
10  
Use to scroll through lists one item at a time, menus, or to pan the Map  
screen.  
11  
Navigation Key  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Magellan RoadMate  
2.2 Rear View  
1
2
3
Speaker  
Antenna  
External Antenna Connection  
Used for audible maneuvering instructions and music playback.  
Rotate up when in use to receive signals from the GPS satellite network.  
See Chapter 4 “Antenna Position” on page 13.  
Plug in an external antenna (optional) for better signal acquisition.  
2.3 Top View  
Used to backup and restore personal navigation data and to transfer  
image files.  
1
Storage Card slot  
Rotate left or right to increase or decrease the volume. Press to repeat  
last voice prompt.  
2
3
Volume Control  
Reset Switch  
Slide to position “1” for power, position “0” to turn power off.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Magellan RoadMate  
2.4 Bottom View  
1
16-pin Connection  
External Power Connection  
Used for future expansion.  
2
Plug in the AC Adapter or the 12 volt vehicle power adapter.  
2.5 Left Side View  
1
2
Stereo Headphone Connection Used to connect the stereo headphones.  
Plug the Magellan RoadMate into your PC to upload music, photos, and  
custom POI’s.  
USB Connection  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Magellan RoadMate  
2.6 Right Side View  
1
Battery Compartment Cover  
Rechargeable battery.  
2.7 Enhanced Cradle - Back View  
External GPS Antenna  
Input  
(External GPS antenna  
sold separately)  
Power In  
Audio Out  
Data In (TMC)  
(Note: There are two audio  
out jacks, one on the receiver  
and one on the enhanced  
cradle. Both audio out jacks  
cannot be used at the same  
time.)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Magellan RoadMate  
2.8 Using Removable Storage Cards  
The Magellan RoadMate is equipped with a storage card slot at the top of the unit (see page 5) that accepts Secure Digital  
(SD) cards and Multimedia Cards (MMC). These cards are used to backup navigation data and to transfer image files to and  
from the hard disk. The storage card slot on your Magellan RoadMate employs what is called a “push-push” method of  
locking and releasing. In other words, when you insert the card you must push it to lock it in, and to release it you must push  
it also. Storage cards come in a variety of sizes and manufacturers, please visit our web site at www.magellangps.com for a  
list of compatible storage cards.  
2.8.1 To Insert the Storage Card:  
Peel back the rubber gasket to expose the storage card slot. Do not completely remove the rubber gasket.  
The storage card can only be inserted in one direction. Do not force the card into the slot.  
Insert the storage card into the slot with the metal contacts going in first and the bevelled edge to the left and the label  
facing front.  
Push the storage card until you hear a click.  
Close the rubber gasket.  
2.8.2 To Remove the Storage card:  
Peel back the rubber gasket to expose the storage card slot. Do not completely remove the rubber gasket.  
Push the storage card until you hear a click. Do not attempt to pull the card out of the slot  
Remove the storage card from the slot.  
Close the rubber gasket.  
2.9 Battery Removal and Installation  
The battery in the Magellan RoadMate 860T is a rechargable lithium-ion battery and should not need to be replaced. In the  
event that the battery fails to charge or is defective, please follow these procedures to remove the battery and install the  
replacement.  
2.9.1 Removing the Battery  
Using a small Phillips screwdriver, remove the screw that holds the battery  
compartment cover in place.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Magellan RoadMate  
Remove the battery compartment cover.  
Remove the battery.  
2.9.2 Installing the Battery  
Insert the new battery with the battery diagram label side up and the pins facing inward. Then, replace the battery  
compartment cover and replace the screw.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Vehicle Installation  
Take care when mounting the Magellan RoadMate in your vehicle, whether using the windshield mount or other mount, that  
it does not obstruct the driver’s view of the road. Make sure that the placement of the Magellan RoadMate and cable does  
not interfere with the operation of vehicle safety devices, such as air bags. You assume the risks associated with damage to  
your vehicle or vehicle’s occupants as a result of how you choose to mount the Magellan RoadMate.  
3.1 Installing the Windshield Mount  
Position the antenna. If an external antenna will be used, leave the antenna folded down  
against the Magellan RoadMate body. If an external antenna is not used, position the antenna  
so that it extends out 90° out from the body.)  
Antenna position without an  
external antenna.  
Attach the enhanced cradle to the back of the unit. Insert the bottom of the unit first then  
snap the enhanced cradle clip at the top into place.  
Slide the windshield mount onto the back of the enhanced cradle.  
Plug the power out cable from the TrafficKit Module into the enhanced cradle  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Vehicle Installation  
Plug the data cable (TMC connector) from the TrafficKit Module into the enhanced cradle  
Connect the antenna cable to the TrafficKit Module.  
Connect the power in cable from the TrafficKit Module to the cigarette lighter adapter cable.  
Press the windshield mount to the glass and slide the locking lever toward the glass.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Vehicle Installation  
Plug the cigarette lighter adapter into a 12vdc receptacle in the vehicle.  
Using the suction cups at the end of the FM antenna, stretch out the FM antenna and attach it to the windshield. Route the  
cabling and the TrafficKit module so that it is secure and out of the way.  
Installation is complete, and you are ready to turn the Magellan RoadMate on and go.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Antenna Position  
The antenna on the Magellan RoadMate 860T is designed in such a way as to receive the satellite signal at the front face of  
the antenna. It is important to angle the antenna so that the front face is mostly toward the sky. Ideally in most vehicles, the  
antenna should be rotated to approximately 90° from the unit to receive the best possible satellite signal.  
'SPOUꢀ'BDF  
'SPOUꢀ'BDF  
"OUFOOBꢀ'SPOUꢀ7JFX  
"OUFOOBꢀ-FGUꢀ4JEFꢀ7JFX  
4BUFMMJUFꢀ4JHOBM  
*ODPSSFDU  
$PSSFDU  
The antenna positioning shown above should be used whenever an external antenna is not being used. If an external  
antenna is attached to the enhanced cradle, the antenna should be put in the down position against the body of the  
Magellan RoadMate 860T  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Navigation Basic Operation  
5.1 Turning the Magellan RoadMate On Out of the Box  
Slide the RESET switch, located at the top of the unit (see “Top View” on page 5) to position  
“1”. If power is connected properly or if the battery is charged sufficiently, the Magellan screen  
will appear followed by the Warning screen. To comply with the warnings, press OK. Next, the  
Quick Tips screen will appear. It is recommended to view the Quick Tips to better familiarize  
yourself with the functionality of the Magellan RoadMate. Otherwise, select ESC to skip viewing  
the Quick Tips at this time. By default, the navigation application will launch and the  
Destination screen will appear.  
5.1.1 Suspend Power or “Sleep” Mode  
While the RESET switch is in position “1”, you can suspend power or, put the unit in “sleep” mode by pressing the  
SUSPEND key (see “Front View” on page 4). While in “sleep” mode, the unit will turn off. Route guidance will resume  
normally when the unit wakes up. Under normal operating conditions, battery power can be maintained for up to two weeks  
while in “sleep” mode. It is recommended that you use the Suspend key rather than switching the unit off in order to acquire  
the GPS signal faster upon resuming normal operation.  
5.1.2 Power Management  
The Magellan RoadMate can be configured to automatically go into “sleep” mode after a specified amount of time. Press the  
MENU key on the unit then, select System Settings and select Power Management. Select the Auto Power Off time and  
then, select ESC. For more information on Power Management, see “Power Management” on page 72.  
5.2 Resetting the Magellan RoadMate  
To turn power off completely, or to reset the unit should it stop responding, slide the RESET switch to position “0”. Wait for  
approximately 10 seconds and then slide the RESET switch to position “1”. If a route was active at the time the unit was  
reset, powering the unit back on will prompt you to resume, or cancel the active route.  
5.3 Adjusting the Volume  
The VOLUME CONTROL lever is located at the top of the Magellan RoadMate (see “Top View” on page 5). Use the lever to  
set the volume of the speaker to a desired level. The volume level indicator will appear on screen.  
5.4 Repeating the Last Command  
While routing to a destination, if you missed the last verbal command, you can repeat it by pressing the VOLUME CONTROL  
lever down.  
5.5 Making Selections  
The Magellan RoadMate comes equipped with a touch screen. To make a menu selection, or enter characters, simply touch  
the screen in the location of the item you wish to select.  
You can also use the NAVIGATION key (see “Front View” on page 4) to scroll around the screen and highlight the item to  
select. When the desired item is highlighted, press the ENTER key to select the item.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Navigation Basic Operation  
5.6 Inputting Text Characters  
Whenever you need to input names, street addresses, etc., the Magellan RoadMate will display a keyboard. Touch the letter  
you want and, if you make a mistake, use the Backspace key to go back one character at a time. The Spacebar is used to  
insert spaces between characters or words.  
Cancel  
Backspac  
Spacebar  
Numerical  
Accept  
Additional  
5.7 Additional Characters (“More” Button)  
When you are entering characters, you may need to add punctuation or other special characters.  
When available, pressing the More button brings up a keypad with the characters shown here.  
5.8 Numerical Characters (“123” Button)  
When available, pressing the 123 button brings up a keypad with the numeric characters shown  
here.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Navigation Basic Operation  
5.9 What Is QuickSpell?  
The Magellan RoadMate uses QuickSpell technology to provide you with the fastest method possible to enter characters.  
QuickSpell eliminates the possibility of a misspelled word or looking for a city or street that is not in the loaded database. As  
you begin entering characters, the QuickSpell feature of the Magellan RoadMate dims out those characters which that are  
not available, thereby speeding up the process of entering data.  
Example:  
Suppose that you need to input the name of a city--in this case, San Francisco.  
Select “S”.  
Select “A”.  
Select “N”.  
Select the spacebar.  
When enough characters have been entered, the Magellan RoadMate will automatically display  
the list of cities; or, if you feel that enough characters have been entered, select OK.  
Use the Navigation key to scroll the list up or down and select “San Francisco, CA” from the  
list.  
The list of items found in the database is limited to 100 items. When over 100 items have been  
found, “Matches: > 100” will be displayed shown in the bottom right corner of the display; you  
may need to press the ESCAPE key and enter additional characters.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Navigation Basic Operation  
5.10 Multi-Word Indexing  
The Magellan RoadMate employs a search feature known as “Multi-Word Indexing”. This feature enables you to search the  
database for possible matches based on the characters entered. The matches returned will start with the characters entered.  
For example:  
You are searching for a street called “East Old Fort Road”. Rather than spell the entire name of  
the street, you can simply enter “Fort”. The Magellan RoadMate will return all database entries  
where on of the words begins with “Fort”. The list returned is subject to the additional  
parameters set by the search such as the city or state entered.  
The database only indexes the main names of streets. In the example above, only the words  
“Old” and “Fort” will be indexed.  
When entering street names, do not enter prefixes such as “N” or “North” unless the whole  
word is part of the street name. By entering “N” the search will return all main street names  
starting with the letter “N”.  
Also, do not enter suffixes such as “St” or “Ave” or “Rd” unless the whole word is part of the street name. By entering “St”  
the search will return all main street names starting with “St”.  
Along with street names, multi-word indexing also supports entering names of cities and points of interest.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
6.1 Guidance Information Screens  
The Magellan RoadMate has three screens you can use to assist you in traveling to your destination: the Map screen, the  
Maneuver List screen, and the TrueView 3D/Split TrueView screen.  
Map: When a new destination is selected and calculated, the Map screen is displayed. This screen displays a map of your  
surrounding area along with the planned route (if calculated) and information about the route. This screen can be accessed  
when no route has been calculated by selecting Map or by pressing the VIEW key (page 4) while at the Destination screen.  
Maneuver List: This screen is available only when a route has been calculated. This screen displays a list of maneuvers to  
follow in order to arrive at the destination. It can also be used exclude a maneuver and then recalculate the route. To access  
the Maneuver List screen, press the VIEW key (page 4) while viewing the Map screen.  
TrueView 3D: This screen is available only when a route has been calculated. This screen displays the next maneuver as a  
3D graphic. It will help you to know which lane to be in and provides you with an easy-to-follow picture of the next maneuver.  
To access the TrueView 3D screen, press the VIEW key (page 4) while viewing the Maneuver List. You can also show the  
TrueView 3D in split mode (see “TrueView Options” on page 60). This view shows the TrueView screen on the left side and  
the Map on the right side.  
Map  
TrueView 3D  
Maneuver List  
Split TrueView  
View  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
6.2 Map Screen  
The Map screen is the most commonly used screen in the Magellan RoadMate and provides you with detailed information  
about where you are and where you are going.  
Current Road  
GPS Signal Strength  
Current Road  
SmartDetour Icon  
Traffic Alert  
POI Icon †  
Planned Route  
(pink)  
Position Cursor (points  
in the direction you are  
traveling)  
2D/3D Map Toggle  
Next Maneuver  
Next Road  
TMC indicator  
Direction of  
Travel  
Distance to Destination  
Estimated Time to  
Destination  
Direction of  
Destination  
Distance to Next Maneuver  
† By touching the POI icon on the screen, you can get information and route to it.  
As you travel, the Map screen constantly updates your location and provides you with not only a map but a visual indication  
of where you are on the map.  
6.3 Changing from 2D to 3D Map View  
The Map screen can be changed between 2D (view overhead of the position cursor, and 3D (view overhead and slightly  
behind). The 3D view offers a more realistic view showing a perspective of the roads ahead. While in 3D Map mode, you can  
still touch icons on the screen to route to them while driving, and you can zoom in and out. You cannot however, scroll the  
map, and the map orientation is set at Heading Up. When in Split TrueView, the map portion of the screen will be in 2D  
mode.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
6.4 Changing the Map Zoom Levels  
While viewing the Map screen, you can zoom in (enlarge the map) by  
pressing the + (plus) key or zoom out (shrink the map) by pressing  
the - (minus) key.  
Zoom In key  
Note: The Zoom In and Zoom Out keys can also be used the scroll through  
long lists. While viewing a list, press the Zoom Out key to scroll the list down  
one page at a time and press the Zoom In key to scroll the list up one page at  
a time.  
Zoom Out key  
6.5 Maneuver List Screen  
The Maneuver List screen can be viewed only after a route has been calculated. From the Map screen, press the VIEW key to  
bring up a list of all of the maneuvers along the route. When you are done viewing the Maneuver List screen, press the VIEW  
key twice to return to the Map screen, or wait a few moments and it will return automatically.  
Next Maneuver  
TMC indicator  
Direction of  
Travel  
Distance to  
Destination  
Direction of  
Destination  
Distance to Next  
Maneuver  
Estimated Time  
to Destination  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
6.6 TrueView 3D Screen  
The Magellan RoadMate uses TrueView 3D technology to display a three-dimensional picture of the next maneuver. The  
TrueView 3D screen can be viewed only after a route has been calculated. From the Map screen, press the VIEW key twice to  
view the TrueView 3D screen.  
Next Maneuver  
TMC indicator  
Direction of  
Travel  
Distance to  
Destination  
Direction of  
Destination  
Distance to Next  
Maneuver  
Estimated Time  
to Destination  
In split mode, the left half of the screen shows TrueView 3D, while the right half of the screen shows the Map.  
Map with  
Planned Route  
Next Maneuver  
TMC indicator  
Direction of  
Travel  
Distance to  
Destination  
Direction of  
Destination  
Distance to Next  
Maneuver  
Estimated Time to  
Destination  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
6.7 Choosing the Route Method  
Every route is calculated based on the Route Method criteria selected. Every time a new destination is selected, the  
Magellan RoadMate prompts you for the method that will be used to calculate the route.  
Shortest Time: This selection calculates a route that should take the least amount of time  
using speed limits and other information in the database. Other factors, such as traffic  
conditions, cannot be used in the calculation of shortest time.  
Shortest Distance: This option calculates the route using the most direct route to the  
destination. This route may not be the fastest due to lower speed limits, left turns or other  
factors.  
Least Use of Freeways: This selection calculates the route avoiding freeways whenever  
possible.  
Most Use of Freeways: This selection calculates the route using freeways as much as possible. This option will use toll  
roads unless specified. See “Route Preferences” on page 61.  
View Destination on Map: Before you select your Route Method, you can see where you are going.  
6.8 Changing the Route Method  
While routing and viewing the Map screen, the Maneuver List screen, or the TrueView 3D screen, press the ESCAPE key.  
Select Route, then select the new route method.  
The route will be re-calculated using the new Route Method chosen and the Map screen will be  
displayed. Press the VIEW key to see the Maneuver List with the new route.  
6.9 Cancelling a Planned Route  
While viewing the Map screen, the Maneuver List screen, or the TrueView 3D screen, press the ESCAPE key.  
Select Yes to cancel the route and display the Destination screen.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
6.10 Detouring from the Planned Route  
If you exit the planned route, the Magellan RoadMate will get you back on course in one of three ways.  
1. If, while driving, you detour from the planned route, the Magellan RoadMate will automatically recalculate the route  
based on your new vehicle position.  
2. If you exit the planned route before its completion and turn off your vehicle, the Magellan RoadMate will switch to  
battery power, unless your cigarette lighter maintains constant power. In either situation, the unit will automatically  
suspend power when enabled through customization. While in “sleep” mode, navigation functions will be suspended  
and guidance will resume when the unit wakes up.  
3. If while routing, the unit fails to respond, reset the unit as described on page 14. The Resume Guidance screen will  
appear.  
Select Resume to continue the route to the selected destination.  
Select Cancel to clear the route and display the Destination screen.  
6.11 Excluding a Maneuver in the Planned Route  
While traveling or setting up your destination you may find it necessary to exclude one of the maneuvers in the Maneuver  
List. This could be due to an accident or street maintenance you want to avoid. The Magellan RoadMate provides you with  
tools to select a specific maneuver, exclude it from the planned route and reroute the trip.  
Press the VIEW key to get to the Maneuver List. Select the maneuver you wish to exclude.  
The details for the maneuver are displayed. Select Exclude.  
The trip will be recalculated, excluding the selected maneuver. This calculation is done using  
the same Route Method that was chosen originally. After the route is recalculated, the Map  
screen is displayed.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
6.12 Displaying Information About Your Present Location  
Anytime that you want to view information about your present location you can press the LOCATE key.  
The first screen displays your heading and the street you are on, the state and city you are  
currently traveling in, the latitude and longitude of your present location, a compass, and your  
speed.  
The next screen displays the street you are currently traveling on, the distance to and the next  
street on the map, and the distance from and the last street you passed.  
6.13 Saving Your Current Location to Your Address Book  
While you are in the Locate screen, you can save your current location to your Address Book.  
Select Save Location.  
The information about your location is displayed. Select Edit Name and/or Edit Information  
and use the keypad to assign a name to the location and other information about it. If the point  
you are saving is off-road, the nearest road information will be used.  
When you have finished, select Save. The location is saved to your Address Book and you are  
returned to the Locate screen.  
6.14 Finding POIs Along Your Route  
While driving along a route, if you need to find a gas station, ATM, or other POI, the Magellan RoadMate can find the nearest  
POI and route to it. Then, when you have completed the side route, resume guidance to your original destination.  
While driving along a route, press the ENTER key.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
Select Dining, ATM, Gas....  
Select the desired POI category.  
A list of the nearest POI’s is displayed. Use the Navigation key to scroll the list up or down (if  
necessary) and select the desired POI.  
The Magellan RoadMate will calculate a new route to the selected POI from your current  
position. When you have arrived at the new destination, you will be prompted to resume  
guidance to your original destination. Select Resume. The Magellan RoadMate will calculate  
the route to your original destination using the Route Method previously selected.  
6.15 Finding a Detour Along Your Route  
While driving along a route, if you encounter traffic, road construction, or other situation you might need to navigate around,  
the Magellan RoadMate can calculate an alternate route to your destination.  
While driving along a route, press the ENTER key.  
Select Detour.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Traveling  
Select the distance of the detour. Select 3 miles, 5 miles, or 10 miles.  
Or, you can enter a custom distance. Select Custom and select the custom distance.  
Enter the number of miles for your detour and then select OK.  
Select Route. The Magellan RoadMate will recalculate the alternate route to your destination.  
You can also choose to have the Magellan RoadMate detour you around traffic automatically by  
enabling smart detour. See “Detour Options” on page 62.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.1 Destination Screen  
Current Country for Destination – page 27  
Select Address – page 28  
Map Button – page 19  
Home Button – page 27  
Address Book – page 32  
Points of Interest – page 47  
Intersection – page 52  
Globe Button – page 27  
7.2 Country Selection (Globe Button)  
Country selection is used to help speed up searching by narrowing down the database. Before  
entering a destination, make sure you select the country where your destination is located. To  
select the country, select the Globe button then, select the country you wish to search. The  
current destination country is displayed at the top of the Destination screen.  
7.3 Entering and Routing to Your Home Address  
The Magellan RoadMate enables you to enter an address to assign to your Home button. The  
Home button allows you one touch access to the address you route to most often. Select the  
Home button.  
If this is the first time using this button, you will be prompted to enter an address. Select Yes.  
Select either Search by City, Search by Zip Code, or Search by State. For this example select  
Search by CIty.  
Enter characters that start a word within the city name (see “Multi-Word Indexing” on page 17). Select OK. Use the  
Navigation key to scroll the list up or down (if necessary) and select the desired city.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on page 17). Do not enter prefixes such  
as “North” or “N”, or the type of street such as “Ave.” or “Street”. Select OK. Use the Navigation key to scroll the list up or  
down (if necessary) and select the desired street.  
Enter the address. The acceptable range of street numbers is displayed at the top of the screen. Enter the street number and  
select Done.  
At this point you can choose to edit the information or, if you are finished, select Save.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Now, when you press the Home button, you will be prompted to either route to or change the  
Home address.  
7.4 Selecting a Destination Using Select Address  
Search by City – page 29  
Search by Zip Code – page 29  
Select Address  
Search by State – page 30  
Previous City – page 31  
A destination can be created by entering the street address that you want to go to. This address is not automatically added  
your Address Book but is saved to your Previous Destinations list if you have routed to it. You have four options: Search By  
City, Search by Zip Code, Search By State, or Previous City. Use Search By City when you know the city that the address can  
be found in. Use Search by Zip Code if you aren’t sure of how to spell the city, but know the zip code. Use Search By State  
when you don’t know, or are unsure of the city name. You will be given a listing of all of the cities for the state you select that  
have the street name you are looking for. Use Previous City to speed up your search by not having to re-enter a city you have  
used before. Additionally, The Previous Cities list places your current city at the top of the list.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.4.1 Search By City  
From the Destination screen, select Select Address and then, select Search By City.  
Enter characters that start a word within the city name (see “Multi-Word Indexing” on  
page 17). Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired city.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.” or  
“Street”. Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired street.  
Enter the street address. The acceptable range of numbers is displayed at the top of the screen.  
Select Done.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the Map  
screen will be displayed.  
7.4.2 Search by Zip Code  
From the Destination screen, select Select Address then, select Search by Zip Code.  
Enter the zip code select OK, then select the city.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.” or  
“Street”. Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired street.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Enter the street address. The acceptable range of numbers is displayed at the top of the screen.  
Select Done.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the Map  
screen will be displayed.  
7.4.3 Search By State  
From the Destination screen, select Select Address then, select Search By State.  
Enter the first few characters for the state and select OK.  
Select the state.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.” or  
“Street”. Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired street.  
Select the desired city from the list. Only those cities that contain the street name and are  
within the state selected are displayed.  
Enter the street address. The acceptable range of numbers is displayed at the top of the screen.  
Select Done.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the Map  
screen will be displayed.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.4.4 Previous City  
From the Destination screen, select Select Address then, select Previous City.  
Select the city from the list.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.” or  
“Street”. Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired street.  
Enter the street address. The acceptable range of numbers is displayed at the top of the screen.  
Select Done.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the Map  
screen will be displayed.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.5 Selecting a Destination Using the Address Book  
Previous Destinations – page 32  
Favorites – page 34  
List Addresses – page 36  
Create New Entry – page 37  
Address Book  
Trip Planner – page 41  
The Address Book can store up to 200 addresses. When you select Address Book you are given five options: Previous  
Destinations lets you select from a list of the last 50 destinations you routed to; List Addresses displays a list of all of the  
addresses you have stored in your Address Book; Favorites gives you a shortened list of entries from your Address Book  
marked as Favorites; Create New Entry lets you add a new address to your Address Book; and Trip Planner (indicated by the  
Trip button) lets you create a multi-destination trip from entries.  
7.5.1 Previous Destinations  
From the Destination screen, select Address Book then, select Previous Destinations.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
previous destination.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Select Route.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.5.1.1 Saving a Previous Destination to the Address Book  
From the Destination screen, select Address Book, then select Previous Destinations.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
previous destination.  
Select Edit.  
The top line (Name) and the bottom line (Information) can be edited. The address cannot  
be changed. Select the line you want to modify. Use the keypad to enter the desired text  
and select OK.  
When you have finished making changes, select Save, then press ESCAPE.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.5.1.2 Deleting A Previous Destination  
From the Destination screen, select Address Book then, select Previous Destinations.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
previous destination.  
Select Delete.  
A dialog box will appear to confirm your selection. Select Yes.  
The Previous Destination is deleted from the list.  
7.5.2 Favorites  
You can add address book entries to your Favorites list by selecting the Favorites box at the bottom of the Edit Address Book  
screen. Only address book entries can be saved as Favorites, Previous Destinations must be saved to the Address Book first,  
and can then be designated as a favorite. The Favorites list is a shorter list of those address book entries that you travel to  
often.  
From the Destination screen, select Address Book, then select Favorites.  
Use the Navigation key to scroll the list up or down (if necessary) and select the destination  
from the list of addresses.  
Select Route.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.5.2.1 Editing a Favorite  
From the Destination screen, select Address Book then, select Favorites.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
favorite.  
Select Edit.  
The top line (Name) and the bottom line (Information) can be edited. The address cannot  
be changed. Select the line you want to modify. Use the keypad to enter the desired text  
and select OK.  
When you have finished making changes, select Save and then, press ESCAPE.  
7.5.2.2 Deleting A Favorite  
From the Destination screen, select Address Book then, select Favorites.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
favorite.  
Select Delete.  
A dialog box will appear to confirm your selection. Select Yes.  
The entry is deleted from the list.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.5.3 List Addresses  
List Addresses shows all entries stored in your address book. It does not include previous destinations but does include those  
entries designated as Favorites.  
From the Destination screen, select Address Book then, select List Addresses.  
Use the Navigation key to scroll the list up or down (if necessary) and select the destination  
from the list of addresses.  
Select Route.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.5.3.1 Editing an Address  
From the Destination screen, select Address Book then, select List Addresses.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
address.  
Select Edit.  
The top line (Name) and the bottom line (Information) can be edited. The address cannot  
be changed. Select the line you want to modify. Use the keypad to enter the desired text  
and select OK. You can also designate the address as a favorite by checking the box at the  
bottom of the screen.  
When you have finished making changes, select Save and then, press ESCAPE.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.5.3.2 Deleting an Address  
From the Destination screen, select Address Book then, select List Addresses.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
address.  
Select Delete.  
A dialog box will appear to confirm your selection. Select Yes.  
The address is deleted from the list and you are returned to the Address Book screen.  
7.5.4 Create New Entry  
Use Create New Entry to add entries to your address book. These entries can then be designated as Favorites to include in  
the Favorites list.  
7.5.4.1 Search by City  
From the Destination screen, select Address Book then, select Create New Entry.  
Select Search by City.  
Enter characters that start a word within the city name (see “Multi-Word Indexing” on  
page 17). Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
city.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.”  
or “Street”. Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
street.  
Enter the street address. The acceptable range of numbers is displayed at the top of the  
screen. Select Done.  
The top line (Name) and the bottom line (Information) can be edited. The address cannot  
be changed. Select the line you want to modify. Use the keypad to enter the desired text  
and select OK. You can also designate the address as a favorite by checking the box at the  
bottom of the screen.  
When you have finished making changes, select Save and then, press ESCAPE.  
7.5.4.2 Search by Zip Code  
From the Destination screen, select Address Book then, select Create New Entry.  
Select Search by Zip Code.  
Enter the zip code and select OK, then select the city.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.” or  
“Street”. Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired street.  
Enter the street address. The acceptable range of numbers is displayed at the top of the screen.  
Select Done.  
The top line (Name) and the bottom line (Information) can be edited. The address cannot  
be changed. Select the line you want to modify. Use the keypad to enter the desired text  
and select OK. You can also designate the address as a favorite by checking the box at the  
bottom of the screen.  
When you have finished making changes, select Save and then, press ESCAPE.  
7.5.4.3 Search by State  
From the Destination screen, select Address Book then, select Create New Entry.  
Select Search by State.  
Use the keypad to enter the first few characters for the state and select OK.  
Select the state.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.”  
or “Street”. Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
street.  
Use the Navigation key to scroll the list up or down and select the desired city. (These are  
all of the cities in your loaded database that have the street name you selected.)  
Enter the street address. The acceptable range of numbers is displayed at the top of the  
screen. Select Done.  
The top line (Name) and the bottom line (Information) can be edited. The address cannot  
be changed. Select the line you want to modify. Use the keypad to enter the desired text  
and select OK. You can also designate the address as a favorite by checking the box at the  
bottom of the screen.  
When you have finished making changes, select Save and then, press ESCAPE.  
7.5.4.4 Previous City  
From the Destination screen, select Address Book, then select Create New Entry.  
Select Previous City.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
city.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.”  
or “Street”. Select OK..  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired street.  
Enter the street address. The acceptable range of numbers is displayed at the top of the  
screen. Select Done.  
The top line (Name) and the bottom line (Information) can be edited. The address cannot  
be changed. Select the line you want to modify. Use the keypad to enter the desired text  
and select OK. You can also designate the address as a favorite by checking the box at the  
bottom of the screen.  
When you have finished making changes, select Save and then, press ESCAPE.  
7.5.5 Trip Planner  
Using the Trip Planner, you can enter multiple destinations for your “trip” and route to each one of them in order.  
7.5.5.1 New  
From the Destination screen, select Address Book, then select Trip (Trip button).  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Select New.  
Use the keypad to enter a name for the new trip and select OK.  
From the pop-up menu, select Add.  
From the Select Trip Planner Address screen, select the method for adding a destination to  
your trip: Map (Map button) will add a destination by selecting a point on the map; Select  
Address will add a destination by creating a new address; Address Book will add a  
destination from a previous destination, Address Book, or favorites; Dining, ATM, Gas...  
will add a destination from the POI database; and Intersection will add a destination of two  
intersecting streets.  
Continue adding destinations. When you are finished, select Save.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.5.5.2 Optimizing a Trip  
With Route Optimization, you can sort the destinations in your trip from closest to farthest.  
From the Trip Planner screen, select Edit.  
Select the trip to optimize.  
Select Optimize.  
The destinations are sorted from closest to farthest from you current location.  
Select Save.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.5.5.3 Guide Me  
From the Destination screen, select Address Book. then select the Trip (Trip button).  
Select GuideMe.  
Select the Trip.  
Select the first destination in the list you wish to route to.  
Note: Selecting the second destination in the list will exclude the first destination,  
selecting the third destination in the list will exclude the first and second destinations, and  
so on.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.5.5.4 Edit  
Destinations within a trip can be moved up or down, deleted, or added to.  
From the Trip Planner screen, select Edit.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Select the trip to edit.  
Select the destination you wish to delete, and select Delete from the pop-up menu.  
Select the destination you wish to change, and select Move Up from the pop-up menu.  
When you have finished, select Save and you are returned to the Trip Planner screen.  
7.5.5.5 Delete and Rename  
From the Trip Planner screen, select Delete, Rename.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Select Delete.  
Select the trip you wish to delete.  
A dialog box will appear to confirm your selection. Select Yes.  
The trip has been deleted.  
Select Rename.  
Select the trip to be renamed.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Use the backspace key to delete the old name; then, enter the new name for the trip. When  
you have finished, select OK.  
The trip has been renamed.  
7.6 Selecting a Point of Interest as a Destination  
Spell Name – page 47  
Select Category – page 49  
Custom POIs – page 51  
Dining, ATM, Gas...  
Points of Interest (or POIs) are commercial or recreational locations, landmarks, or services that are preloaded into the  
Magellan RoadMate database. There are over six million POI’s in the database, which range from restaurants, parks, gas  
stations, and banks, to schools and police stations, and more. The purpose of the POI database (accessed through the  
Dining, ATM, Gas... menu option) is to provide you with a list of popular destinations without having to enter the address  
manually in order to route to them.  
7.6.1 Spell Name  
If you know the name of the POI you are looking for, find it using the Spell Name feature. You can enter any word contained  
within the name and the Magellan RoadMate will return all entries containing that word.  
From the Destination screen, select Dining, ATM, Gas.., then select Spell Name.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Enter the name of the POI.  
7.6.1.1 Nearest  
Selecting Nearest will list the POIs matching the name you entered from closest to farthest  
from your current position. Select Nearest.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
POI.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.6.1.2 List By City  
Selecting List by City will list the POIs matching the name you entered within a selected  
city. Select List by City.  
Enter characters that start a word within the city name (see “Multi-Word Indexing” on  
page 17). Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
city.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
POI.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
7.6.1.3 Select Category  
Selecting Select Category enables you to narrow the list of POIs by selecting the category of  
the name you spelled. Select Category.  
Use the Navigation key to scroll the list up or down and select the desired POI category.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
POI.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.6.2 Select Category  
If you do not know the name of the POI you are looking for, but know the category (restaurant, bank, gas station, etc.), you  
can find it using Select Category  
From the Destination screen, select Dining, ATM, Gas..., then select Select Category.  
Select the POI category.  
7.6.2.1 Nearest  
Selecting Nearest will list the POIs in the category selected from closest to farthest. Select  
Nearest.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
A list of all the POI’s in the selected category nearest to your current position is displayed.  
Select the POI from the list.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.6.2.2 List by City  
Selecting List by City will list the POIs in the category selected within a specified city.  
Select List by City.  
Enter the name of the city you wish to search from. When you are finished, select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
city.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
POI.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.6.2.3 Spell Name  
Selecting Spell Name will list the POIs in the category selected, matching the name you  
entered. Select Spell Name.  
Enter the name of the POI. When you are finished, select OK.  
Select Nearest to list the POIs matching the characters entered that are nearest to your  
current position.  
Select List by City to list the POIs matching the characters entered that are nearest to a  
particular city. Enter the name of the city. When you are finished, select OK. Select the city  
from the list.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
POI.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.6.2.4 Cuisine Type  
When selecting restaurants, you are presented with an additional method for finding POIs.  
Select Cuisine Type. Use the Navigation key to select the type of restaurant you prefer.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
POI.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.6.3 Custom POIs  
Please refer to page 78 for information on creating and loading Custom POIs.  
From the Destination screen, select Dining, ATM, Gas..., then select Custom POIs.  
Select the category.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
If the POI list has more than 15 returns, you can further narrow the search by selecting  
either Nearest or Spell Name. Select the desired POI from the list.  
Select Route to go to the selected Address, or select Cancel to return to the Select Custom  
POI menu.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.7 Selecting an Intersection as a Destination  
Search by City – page 52  
Search by Zip Code – page 53  
Intersection  
Search by State – page 54  
Previous City – page 54  
An intersection of two streets can be used as a destination for your trip. The search for the intersection can be done whether  
or not you know the city. If you know the city, you can start there; if you are unsure of the city, you can start with the state.  
7.7.1 Search by City  
From the Destination screen, select Intersection then, select Search by City.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Enter characters that start a word within the city name (see “Multi-Word Indexing” on  
page 17). Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
city.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.”  
or “Street”. Select OK.  
Use the Navigation key to scroll the list up or down and select the first street from the list.  
Enter characters that start a word within the name of the second street and select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the second  
street from the list.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.7.2 Search by Zip Code  
From the Destination screen, select Intersection then, select Search by Zip Code.  
Enter the zip code and select OK, then select the city.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.”  
or “Street”. Select OK.  
Use the Navigation key to scroll the list up or down and select the first street from the list.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Selecting Destinations  
Enter characters that start a word within the name of the second street and select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the second  
street from the list.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.7.3 Search by State  
From the Destination screen, select Intersection then, select Search by State.  
Enter the first few characters for the state and select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the state from  
the list.  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.”  
or “Street”. Select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the first street  
from the list.  
Enter characters that start a word within the name of the second street and select OK.  
Use the Navigation key to scroll the list up or down (if necessary) and select the second  
street from the list.  
Select the desired Route Method.  
The Magellan RoadMate will calculate the route. When the calculations are complete, the  
Map screen will be displayed.  
7.7.4 Previous City  
From the Destination screen, select Intersection then, select Previous City.  
Use the Navigation key to scroll the list up or down (if necessary) and select the desired  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
Navigation Options are only available when you are in Navigation Mode. When going to the Main  
Menu from the Music Player or from the Photo Viewer, this option will be grayed out.  
To access these features, press the MENU key on the unit and select Navigation Options.  
8.1 Configuration  
Configuration enables you to customize the advanced navigation features of the Magellan RoadMate.  
Select Configuration.  
8.1.1 POI Selection  
From the POI Selection menu, you can choose which icons to display on the Map screen. We recommend being selective  
about which icons you choose to display in order to prevent your map screen from being cluttered. For a list of POI  
Categories, see “POI Categories” on page 91.  
Select POI Selection.  
Select Mark All to display all POI icons on the Map screen.  
Select Clear All if you wish not to have any POI icons displayed on the Map screen.  
You can also select individual icons to display or hide on the Map screen. When you have  
finished, press the ESCAPE key to return to the Configuration menu.  
8.1.2 Custom POIs  
The Custom POI menu enables you to select POIs previously loaded into your Magellan RoadMate using the Magellan  
RoadMate POI Manager software (see page 78). The following instructions are assuming that you have loaded one or more  
custom POIs into your Magellan RoadMate.  
Select Custom POIs.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
Select a POI File.  
Use the Navigation key to scroll the list up or down (if necessary) and select a POI file. With the  
file selected, you are returned to the Custom POIs menu.  
Select Display Categories.  
The categories you created are displayed in the same way as the built-in POIs.  
Select Mark All to display all POI icons on the Map screen. Select Clear All if you wish not to  
have any POI icons displayed on the Map screen. You can also select individual icons to display  
or hide on the Map screen.  
When you have finished, press the ESCAPE key to return to the Custom POIs menu.  
You can also be alerted when you approach a custom POI. The Set Alarm function works for  
Custom POIs only and only if the POI has been selected to show on the Map screen. Select Set  
Alarms.  
Again, you can select all, none, or individual POIs to have an alert set. Select Mark All to set an  
alert for all custom POI icons on the Map screen. Select Clear All if you wish not to have any  
alerts set for custom POI icons displayed on the Map screen. You can also select individual  
categories to have an alert set.  
When you have finished, press the ESCAPE key to return to the Custom POIs menu.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
With the POI alerts set, you can now choose at what point you will be alerted. Select Alert  
Parameters.  
Select the POI category to customize.  
The Detection Angle is set to alert you when you are within so many degrees of the POI.  
Select Detection Angle.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
Use the numeric keypad to enter the number of degrees in which to set the alert. When you  
have finished, select OK.  
The First Warning is set to alert you when you are within a certain number of feet from the POI.  
Select First Warning.  
Use the numeric keypad to enter the number of feet in which to alert you. When you have  
finished, select OK.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
The Last Warning is set as a final alert when you are within a certain number of feet from the POI.  
Select Last Warning.  
Use the numeric keypad to enter the number of feet in which to alert you. When you have  
finished, select OK.  
When you have set the parameters as you like, select Save.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
8.1.3 Map Options  
Map Options enable you to determine the behavior of the Map while you are driving.  
Select Map Options.  
With Scrolling enabled, the vehicle position icon will always remain in the same position with  
the map scrolling, or moving as while the vehicle is in motion. With Scrolling disabled, the  
vehicle position icon will move forward slightly; then, the map will scroll down. Having Scrolling  
disabled allows for a faster display.  
Heading Up sets the map display so that the direction of travel is always at the top of the  
screen. North Up sets the map display so that North is always at the top of the screen. North  
Up is only available in 2D Map mode.  
Select Miles or Kilometers as the unit of measure for distance.  
When you have finished, select Save.  
8.1.4 TrueView Options  
TrueView options enable you to control how and when the TrueView screen is displayed. Select  
TrueView Options.  
Select Split TrueView to enable the TrueView/Map Screen mode. See “TrueView 3D Screen” on  
page 21.  
Select Disable TrueView if you do not want the TrueView screen to appear during routing.  
Select Manual TrueView to show the TrueView screen only by pressing the View key.  
Select Auto TrueView to have the TrueView screen appear automatically when the next maneuver is approaching.  
When you have finished, select Save.  
8.1.5 Select Map Color  
Select Map Color.  
With Automatic Night Mode enabled, the Magellan RoadMate will switch between a Day screen and a Night screen based  
on sunrise and sunset times for your current location.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
Select Day Screen to choose a color scheme for the map while you are driving during the  
day.  
Select Night Screen to select a color scheme for driving at night.  
When you have finished, select Save.  
Select from nine available color schemes:  
When you have finished, select Save and you will be returned to the Select Map Color menu.  
8.1.6 Route Preferences  
Route Preferences enable you to set parameters for the Magellan RoadMate to follow when calculating a route. Select Route  
Preferences.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
Avoid Toll Roads instructs Magellan RoadMate to avoid known toll roads when calculating a  
route.  
Automatic Re-Route will cause the Magellan RoadMate to try up to three times to  
automatically re-route to the destination when it has detected that the vehicle has deterred  
from the calculated route.  
When you have finished, select Save.  
8.1.7 Detour Options  
The Magellan RoadMate comes equipped with SmartDetour. If you are driving on the freeway with SmartDetour enabled and  
your speed drops below 15 MPH, you may press the detour icon on the Map screen in order for the Magellan RoadMate to  
calculate an alternate route around traffic.  
Select Detour Options.  
Select the distance of the detour. You can select from a preset distance of three miles, five  
miles, or 10 miles.  
You can also select a custom distance. Select Custom, and then select the button to the right  
to enter a custom distance.  
Enter the number of miles and select OK.  
Next, select the amount of time the Magellan RoadMate will wait before alerting you. Select the  
Time button.  
Enter the number of minutes and select OK.  
Enable Automatic Detour is selected by default as shown by the checkbox mark. To disable  
automatic detour, deselect Enable Automatic Detour.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
When you have finished, select Save.  
When you encounter traffic, and the set time has elapsed, the Detour icon will flash on the Map  
screen. Touch the icon on the screen to have the Magellan RoadMate calculate the detour. You  
can choose to ignore the Detour alert; and after one minute it will stop flashing until the set  
time has elapsed again when it will alert you once more.  
8.1.8 Voice Options  
From the voice options menu, you can select to have your voice prompts announced in either a male or a female voice in the  
language currently enabled (refer to “Language” on page 73).  
Select Voice Options.  
Choose Male Voice or Female Voice.  
Choose Announce street name to turn text-to-speech on or off.  
When you are finished, select Save.  
8.1.9 Menu Colors  
You can change the color of the menu screens by selecting one of four color schemes.  
Select Menu Colors.  
Select the desired color scheme.  
When you have finished, select Save.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
8.1.10 Tone Options  
As you approach a maneuver, an audible alert sounds to let you know to make the maneuver.  
Select Tone Options.  
Select either Bell, Chime, or Beep.  
When you have finished, select Save.  
8.1.11 GPS Options  
GPS Options provide you with information on the satellite signal as well as the ability to speed up signal acquisition time.  
8.1.11.1 GPS Status  
The GPS Status screen is available by pressing the GPS Signal icon on the Map screen  
(page 19) as well as through the GPS Options menu. GPS Status monitors the satellite signal.  
For more information on the GPS Status screens refer to “GPS Status Screen” on page 93.  
8.1.11.2 Set GPS Position  
Set GPS Position enables you to manually set the location of the Current Position icon. If you have travelled a long distance  
with the unit off, it may take some time for the unit to reacquire a satellite signal. By manually setting the position of the  
unit, you are telling the unit where you are and will speed up the satellite signal acquisition. Make sure you first select the  
country you are in by pressing the Globe button on the Destination screen (see “Country Selection (Globe Button)” on  
page 27). Select Set GPS Position.  
Enter characters that start a word within the city name (see “Multi-Word Indexing” on  
page 17). Select OK. Use the Navigation key to scroll the list up or down (if necessary) and  
select the desired city.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
Enter characters that start a word within the street name (see “Multi-Word Indexing” on  
page 17). Do not enter prefixes such as “North” or “N”, or the type of street such as “Ave.” or  
“Street”. Select OK. Use the Navigation key to scroll the list up or down (if necessary) and  
select the desired street.  
Enter the street address. The acceptable range of numbers is displayed at the top of the screen.  
If you do not know the exact address, just select Done and the Magellan RoadMate will use the  
lowest number in the range. Select Done to continue. You will be returned to the Configuration  
menu.  
Go to the Map screen. Your current position is now set to the address you entered.  
8.1.12 Simulator Mode  
In Simulator Mode, you can demonstrate the capabilities of the Magellan RoadMate without actually driving. In order for the  
simulation to work, you must set a route first. Select Simulator Mode.  
Select Simulate to begin the simulation.  
Set the speed variance of the simulation: x1 will “drive” at normal speed using known speed  
limits; x1.5 will “drive” at one and a half times normal speed; x2 will “drive” at two times  
normal speed.  
Return to the Map screen to view the simulation.  
To disable Simulator Mode, select Stop, or when the power is turned off the Simulator will stop.  
8.1.13 Map Regions  
The Magellan RoadMate 860T comes preloaded with North American and European map data. If you are travelling to  
Europe, you can take your Magellan RoadMate with you and use it while you are driving abroad. To unlock the European  
map, contact our Customer Service department for pricing and unlock-code information or visit our Web site at  
www.magellanGPS.com.  
Select Map Regions.  
Select Europe and then select Unlock.  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
Select Code.  
Use the keypad to enter the unlock code. When you have finished, select OK.  
Select Unlock.  
The database is unlocked. Select OK.  
Select Europe and then select Switch.  
Select Yes. After the unit has powered down, turn the unit back on and the new map will begin  
loading. When it has finished, you will have access to the European maps.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
8.1.14 Automatic Volume  
The Magellan RoadMate can be set to automatically increase the volume when the vehicle exceeds 45 MPH in order to  
compensate for road noise.  
Select Automatic Volume.  
Select the number increment by which to increase the volume.  
Select Enable.  
When you have finished, select Save.  
8.1.15 TMC Options  
TMC (Traffic Message Channel) Options provide tools to use in conjunction with the TrafficKit.  
(See the TrafficKit User Manual for more detailed information.)  
Under Incident Options the different types alerts displayed can be turned on or off.  
TMC Selection provides a way to turn the TrafficKit on or off. How alerts are handled can be  
set under TMC Selection. Turning on Use alternate route instructs the Magellan RoadMate to  
modify the route to avoid the traffic incident at a selected distance or it can be set to just  
provide an alert at a selected distance.  
Subscriptions is used to enter codes received from a subscription provider.  
Restore Defaults resets TMC Options to factory settings. This will not remove any subscriptions entered.  
TMC Status provides detailed information about the provider being used and the traffic signal being received.  
8.1.16 \Backup and Restore  
The Magellan RoadMate 860T has the capability to back up your information (Address Book, Previous Destinations, etc.) to  
an optional storage card.  
8.1.16.1 Backup to Mass Storage Card  
Select Backup and Restore then, select Backup to Mass Storage Card.  
If you do not have a card inserted, you will be prompted to insert a card. Make sure the card is  
unlocked to allow data to be copied to it. Insert a card and reselect Backup to Mass Storage  
Card.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
A dialog box will appear asking you to confirm your selection. Select Yes.  
The files are copied to the storage card.  
8.1.16.2 Restore from Mass Storage Card  
To restore the files to the hard disk, select Backup and Restore then, select Restore from  
Mass Storage Card.  
If you do not have a card inserted, you will be prompted to insert a card. Insert a card and  
reselect Restore from Mass Storage Card.  
A dialog box will appear asking you to confirm your selection. Select Yes.  
The files are copied to the hard disk.  
8.1.17 Clear Address Book  
Under Clear Address Book all addresses entered in Previous Destinations, Address Book, and  
Favorites can be cleared.  
Select the items to be cleared and select Delete. Select Yes to confirm the deletion.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
8.1.18 Map Information  
Product Information displays information about the map and database installed in your  
Magellan RoadMate. This information aids our Technical Support Representative in finding a  
solution to whatever problem you may have.  
8.2 Trip Computer  
The Trip Computer is a valuable tool for recording the mileage and time spent driving while on business or vacation. The  
information for the trip can be saved and viewed at any time, providing you easy access to information on your current trip,  
as well as previous trips.  
To access these features, press the MENU key on the unit and select Navigation Options.  
Select Trip Computer.  
8.2.1 Current Trip  
When you begin a new trip and you need to record the information, access the Trip Computer. There you can save the  
information displayed for the current trip (if needed) and reset the Trip Computer to zero in preparation for your new trip.  
Select Trip Computer  
Select Current from the list of saved Trip Reports.  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
The Trip Computer is always in a “Running” state. The information for the current trip is  
displayed.  
8.2.1.1 Stopping or Starting the Trip Computer  
At any time the Trip Computer can be stopped and started. If the Trip Computer is currently  
running, select Stop. The Trip Computer will stop recording until restarted or reset.  
While the Trip Computer is in a “Stopped” state, select Start to continue recording the current  
trip or select reset to begin a new trip.  
8.2.1.2 Saving the Current Trip Report  
When you have finished with your trip, you can save the information for later viewing. Select  
Save at any time.  
Use the keypad to enter a name for the Trip Report and select OK when you are finished.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: Navigation Options  
8.2.1.3 Resetting the Trip Computer  
Before starting a new trip that you want to record, you need to reset the Trip Computer first.  
Select Reset and the information will be set to zero. The Trip Computer will remain in a  
“Running” state.  
8.2.1.4 Viewing a Saved Trip Report  
From the Trip Computer screen, select the Trip Report you wish to view.  
The saved Trip Report is displayed. Press the ESCAPE key when you are finished to view the  
trip and return to the Trip Computer screen.  
8.2.1.5 Deleting a Trip Report  
Select the Trip Report to be deleted.  
Select Delete.  
The trip is deleted and you are returned to the Trip Computer screen.  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9: System Settings  
The System Settings Menu contains system wide customization features which include:  
Brightness, Power Management, Password, and Language.  
To access these features, press the MENU key on the unit and select System Settings.  
9.1 Brightness  
To change how light the screen appears, select Brightness.  
Use the right arrow to make the screen appear lighter, and use the left arrow make the  
screen appear darker.  
With On-battery dimming enabled, the screen will decrease in brightness by 20% to save  
some battery power.  
When you have finished, select ESC.  
9.2 Power Management  
The Power Management features enable you to customize the features that will conserve  
battery power and display life. Select Power Management.  
Select the time period to put the unit in “sleep” mode.  
Select to enable or disable turning the screen off when music is being played.  
When you have finished, select ESC.  
9.3 Password  
9.3.1 Set Password  
You can protect the unit form unwanted use by enabling a password. Select Password.  
Select Set to enter a password. Use the keypad to enter the desired password. When you  
have finished, select OK.  
Select Confirm to re-enter the password. Use the keypad to re-enter the password exactly  
as you entered it the first time. When you have finished, select OK.  
Select OK to activate the password. To return to the System Settings menu without setting  
the password, select ESC.  
Once the password is enabled, you will be required to enter it when the unit is turned on or when it wakes up from “sleep”  
mode.  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9: System Settings  
9.3.2 Remove Password  
Select Password and use the keyboard to enter the password. When you have finished, select OK. Then, from the Set New  
Password screen, select OK.  
9.4 Language  
To change the language for the menu text and voice prompts for navigation, select  
Language.  
Select the desired language. A dialog box will appear asking you to confirm your selection.  
Select Yes.  
The unit will restart itself with the new language enabled.  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 10: System Status  
The System Status menu give you further options to check the performance of your Magellan RoadMate.  
10.1 Product Information  
Select Product Information to show the current application software versions. Also, the  
current hardware and firmware versions will be displayed.  
10.2 User Storage  
Select User Storage to display the available space and total space of the hard disk and, if  
inserted, the storage card. Note: Although 10 GB of storage on the unit hard disk is  
available, the actual storage may vary and can be slightly less.  
10.3 Diagnostics  
Diagnostics enables you to test key performance elements of the Magellan RoadMate  
10.3.1 Audio Test  
The Audio Test will check the performance of the built-in speaker.  
10.3.2 Touchscreen Test  
The Touchscreen test will enable you to recalibrate the touchscreen should it not be  
tracking properly.  
10.3.3 Keypad Test  
The Keypad test will determine if the buttons on the unit are functioning.\  
10.3.4 Video Test  
The Video test will test to determine if the screen is displaying colors properly.  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 11: Help  
The Help feature provides you with an interactive tutorial on the features and functions of the Magellan RoadMate along with  
contact information should you need assistance.  
11.1 Quick Tips  
Quick Tips for New Users provides information in the following categories on basic usage and how to get the best signal  
reception:  
•
•
•
•
•
•
•
Getting Started  
Unobstructed View  
Remain Stationary  
Antenna Position  
Entering a Destination  
Other Important Info  
Registering You Product  
11.2 Contact Us  
If you experience problems using your Magellan RoadMate, you can contact us at the numbers  
displayed.  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 12: Magellan RoadMate Tools Installation  
12.1 Installing the Software  
Insert the Magellan RoadMate Tools PC Application CD into your PC’s CD drive.  
The setup application will begin automatically. If it does not, browse your computer’s CD drive and double-click on the  
setup.exe file.  
Select a default language for the Application.  
The Welcome screen will appear to begin the installation process.  
Choose a destination for the application. Select Next to use the default  
location, or select Browse to choose a custom destination.  
Next, choose a Program Folder to place the application icons.  
The Magellan RoadMate Tools software will be installed. After it has finished  
installing, a dialog box pertaining to Microsoft DIgital Signatures may appear,  
select OK  
When it has finished, to can have the installer launch the application  
automatically, or deselect to exit without launching the application. Select  
Finish.  
12.2 Connecting Your Magellan RoadMate  
Connect the small end of the USB cable to the USB port on the unit and the large end to an available USB port on your  
personal computer. See “Left Side View” on page 6.  
Connect the small end of the External Power cable to the power port on the unit and plug the other end of the cable into a  
standard, 110 VAC wall outlet. See “Bottom View” on page 6.  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 13: Magellan RoadMate POI Manager  
The Magellan RoadMate POI Manager enables you to transfer custom points of interest files from your computer to your  
Magellan RoadMate.  
Before we add any custom POI’s to the unit, you should understand how the POI Manager plots POIs.  
13.1 Latitude  
Latitude can be expressed by dividing Earth into horizontal segments  
totalling 180 degrees. Starting at the Equator, or zero degrees Latitude,  
90° (North Pole)  
80°  
lines (or Parallels) are drawn in 10-degree increments 90 degrees to the  
north and 90 degrees to the south. If your location is below the Equator,  
you are at a South Latitude.  
70°  
60°  
50°  
40°  
30°  
20°  
10°  
0°  
Equator  
0°  
10°  
20°  
30°  
40°  
50°  
60°  
70°  
80°  
90° (South Pole)  
13.2 Longitude  
Conversely, longitude lines can be expressed by dividing Earth into vertical  
segments totalling 360 degrees. Starting at the Prime Meridian (which is  
The Royal Observatory in Greenwich, England), or zero degrees Longitude,  
lines are drawn in 10-degree increments 180 degrees to the West and 180  
degrees to the East. If your location is on the western hemisphere, you are  
at a West Longitude.  
West Longitude  
70° 50° 30° 10° 10° 30° 50° 70° 90°  
80° 60° 40° 20° 0° 20° 40° 60° 80°  
Additionally, to narrow down your location further, each 10-degree segment  
is divided into 60 smaller segments called minutes and, still further, each  
minute is divided into 60 segments called seconds.  
90°  
East Longitude  
To express this in coordinates, the city of Los Angeles is located at 34°  
(degrees) 03’ (minutes) and 08 (seconds) North of the Equator, and 118°  
(degrees) 14’ (minutes) and 42 (seconds) West of the Prime Meridian.  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 13: Magellan RoadMate POI Manager  
13.3 Altitude  
Each location can also have an Altitude. Altitude is expressed  
by how far the point is above or below the level of the ocean, or  
Sea Level. For example, Los Angeles, California is about 300  
feet above sea level. Death Valley, California is about 270 feet  
below sea level.  
100’ Above  
80’ Above  
60’ Above  
40’ Above  
20’ Above  
Sea Level 0’  
20’ Below  
40’ Below  
60’ Below  
80’ Below  
100’ Below  
The POI Manager has a single interface for loading, adding, and deleting custom POIs from your Magellan RoadMate.  
Using the USB cable provided with your Magellan RoadMate, insert the large end of the USB cable into an available USB  
port on your computer.  
Turn on your Magellan RoadMate by sliding the Reset switch to position “1” (see “Top View” on page 5), or by pressing the  
Suspend button (see “Front View” on page 4) to wake up the receiver if the unit is in “sleep” mode.  
When the Warning screen appears, insert the small end of the USB cable into the USB port on your Magellan RoadMate. See  
“Left Side View” on page 6.  
Launch the Magellan RoadMate Tools application. From the Magellan RoadMate Tools screen, click on POI.  
The left side of the window shows the contents of your computer and the right side of the window shows the contents of the  
Magellan RoadMate.  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 13: Magellan RoadMate POI Manager  
13.4 Opening a POI File  
When you start the POI Manager the contents of your “My POI’s” folder will be displayed. This is the default location for  
storing custom POI files.  
Locate the POI files you wish to load. When you have selected a file, the Copy To Unit arrow will turn green. Click on the  
arrow to copy the file to your unit.  
When you have finished copying files, remove the USB cable from the unit.  
13.5 Creating a New POI FIle  
There are two ways to create a POI file. You can either add POI’s individually, or you can import a character delimited file  
containing the information need to plot the POI’s. To plot a POI, each item must have a name, longitude, and latitude.  
Longitude and latitude must be in decimal format.  
13.6 Adding Individual POI’s  
Click on the New POI File Button to launch the POI Editor.  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 13: Magellan RoadMate POI Manager  
Click on the Add button  
.
Enter the Name, the Latitude, and the Longitude. The Altitude and Description fields are optional.  
Select the Category field and select New. A dialog box will appear to create a new POI category. Enter the Name and assign  
an Image (icon) for the POI. The Description field is optional.  
The Alert feature is an audible alarm that lets you know when you are within a certain distance from the POI. You can set an  
initial reminder (Distance 1), a secondary reminder (Distance 2).  
Distance 1  
Distance 2  
Select you preferred unit or measure (Meters or Feet).  
The Detection angle sets the range of alert in degrees from the POI.  
Select Activate alert for this category to enable the alert settings.  
When you have finished, select OK.  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 13: Magellan RoadMate POI Manager  
13.7 Importing a Data FIle  
The POI Manager software supports ASCII file format (.ASC,.CSV,.TXT); GPS Exchange file format (.GPS,.XML); Magellan  
Waypoint file format (.WPT,.RTE); and Garmin PCX5 Waypoint file format (.WPT,.RTE).  
Click on the Open button  
.
Select the file you wish to import and click Open.  
Start by choosing which line in the data file to start importing data. If your data file has a header row, this row will generate  
an error so you should start at line two or below.  
Next, choose how the data is separated and click on Next.  
You now need to define the data columns. Click on the pull down menu and assign a field name to the appropriate column.  
Click on Finish.  
Click on The Save POI file button. Assign a name to your file and click on Save.  
Close the POI File Editor. Select the POI file you just created and click on the transfer button (right arrow) to upload the file  
to your Magellan RoadMate.  
See page 55 for information on accessing custom POIs on your Magellan RoadMate.  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 14: Magellan RoadMate Music Manager  
The Magellan RoadMate Music Manager enables you to transfer song files in MP3 or WMA format from your computer to  
your Magellan RoadMate, or from your Magellan RoadMate to your computer. The Magellan RoadMate has approximately  
10 GB of hard disk space available for storage of music files, image files, and custom POI files.  
Using the USB cable provided with your Magellan RoadMate, insert the large end of the USB cable into an available USB  
port on your computer.  
Turn on your Magellan RoadMate by sliding the Reset switch to position “1” (see “Top View” on page 5), or by pressing the  
Suspend button (see “Front View” on page 4) to wake up the receiver if the unit is in “sleep” mode. When the Warning  
screen appears, insert the small end of the USB cable into the USB port on your Magellan RoadMate. See “Left Side View”  
on page 6.  
Launch the Magellan RoadMate Tools application. From the Magellan RoadMate Tools screen, click on Music.  
The left side of the window shows the contents of your computer and the right side of the window shows the contents of the  
Magellan RoadMate.  
Locate the song files you wish to load. When you have selected a file, the Copy To Unit arrow will turn green. Click on the  
transfer arrow to copy the file to your unit.  
In the same way, if you have loaded song files onto your Magellan RoadMate from another computer, you can copy the files  
from your unit to your computer.  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 15: Music Player  
The Magellan RoadMate Music Player enables you to play music files in MP3, or WMA format, stored on the hard disk of  
your Magellan RoadMate. If you have not already done so, you must install the Magellan RoadMate Tools application  
(page 76) and transfer files onto your unit using the Magellan RoadMate Music Manager (page 82).  
Press the MENU key on the unit (see page 4) and select the Music Player.  
.
The Music Player control pad will appear.  
15.1 Single Song Play  
Select Browse Music  
Use the Navigation key or the Down arrow  
to select the song file you wish to play and  
press OK.  
The song will begin playing automatically.  
At the top of the screen is displayed the name of the song, the artist (if available), the selected  
play mode, the elapsed time, and the song duration.  
Press the Play/Pause button to suspend song play. To resume song play, press the Play/Pause  
button again.  
Press the Stop button to stop song play. Once a song has been stopped, pressing the Play/  
Pause button will start the song from the beginning.  
15.2 Multiple Song Play  
Multiple song play enables you to create a “playlist”. A playlist consists of one or more songs in a group that can be played  
continuously.  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 15: Music Player  
Select Playlist  
The Playlist menu will appear. To exit from the playlist menu, select ESC.  
15.2.1 Play  
To hear a previously created playlist, select Play.  
Use the Up or Down arrow to select the desired playlist. Select OK.  
The songs will begin playing automatically in order.  
15.2.2 Create  
To make a new playlist, select Create.  
Use the backspace key (<-) to erase the default name; and the keypad to enter a new name for your playlist. When you have  
finished, select OK.  
The next screen to appear shows the song files stored on the hard drive on the left side, and the playlist on the right side.  
Use the arrow buttons on the left side of the screen to highlight the Music folder and then, select List Files.  
Use the arrow buttons to highlight the song files you wish to add to the playlist. Select Add to Playlist (right arrow) to add  
the highlighted song to the playlist.  
Continue adding files to the playlist. When you have finished, select OK.  
15.2.3 Modify  
Modify enables you to add or remove songs from the selected playlist. Select Modify.  
To remove a song from the playlist, use the arrow keys on the right side of the screen to highlight the desired song and then  
select Remove From Playlist (left arrow).  
Use the arrow buttons on the left side of the screen to highlight the song files you wish to add to the playlist. Select Add to  
Playlist (right arrow) to add the highlighted song to the playlist.  
Continue adding files to the playlist. When you have finished, select OK.  
15.2.4 Delete  
To remove a playlist, select Delete.  
Select the playlist you wish to delete and select OK.  
A dialog box will appear asking to confirm your selection. Select Yes to delete the playlist.  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 15: Music Player  
15.2.5 Rename  
If you want to change the name of a playlist, select Rename.  
Select the playlist you wish to rename and then, select OK.  
Use the backspace key (<-) to erase the name; and the keypad to enter a new name for your playlist. When you have  
finished, select OK.  
15.3 Play Mode  
While in single song play, select Play Mode for song play options.  
Repeat All - Repeats all the songs in the current playlist starting at the beginning of the order.  
This function works only if there are two or more songs in the playlist.  
Repeat - repeats the song that is currently playing.  
Preview - Plays the first five seconds of each song in the current playlist.  
Normal - Plays all songs in the current playlist in order.  
Random - Plays the songs in the current playlist in random order.  
15.4 List Songs  
Select List Songs to view the current playlist.  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 15: Music Player  
15.5 Equalizer  
The Equalizer provides advanced sound options so you can customize the quality of the playback. The equalizer will only be  
available for MP3 format sound files. Select an equalizer preset from the following preconfigured options: Default (flat),  
Jazz, Classical, Rock, Techno, Dance Hall, Live, Full Bass, Full Treble, and Full Bass & Treble. You are not able to however,  
manually set the equalizer.  
Select the Equalizer  
Select the equalizer preset by pressing the button at the top of the screen  
.
When you are satisfied with your selection, select OK. To exit without setting the equalizer, select ESC.  
15.6 Help  
Select Help  
for descriptions of the Music Player buttons.  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 16: Magellan RoadMate Photo Manager  
The Magellan RoadMate Photo Manager enables you to transfer image files in either JPG or BMP format from your computer  
to your Magellan RoadMate, or from your Magellan RoadMate to your computer. The Magellan RoadMate has approximately  
10 GB of hard disk space available for storage of music files, image files, and custom POI files.  
Using the USB cable provided with your Magellan RoadMate, insert the large end of the USB cable into an available USB  
port on your computer.  
Turn on your Magellan RoadMate by sliding the Reset switch to position “1” (see “Top View” on page 5), or by pressing the  
Suspend button (see “Front View” on page 4) to wake up the receiver if the unit is in “sleep” mode. See “Top View” on  
page 5. When the Warning screen appears, insert the small end of the USB cable into the USB port on your Magellan  
RoadMate. See “Left Side View” on page 6.  
Launch the Magellan RoadMate Tools application. From the Magellan RoadMate Tools screen, click on Photo.  
The left side of the window shows the contents of your computer and the right side of the window shows the contents of the  
Magellan RoadMate.  
Locate the image files you wish to load. When you have selected a file, the Copy To Unit arrow will turn green. Click on the  
transfer arrow to copy the file to your unit.  
In the same way, if you have loaded image files onto your Magellan RoadMate from another computer, you can copy the files  
from your unit to your computer.  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 17: Photo Viewer  
The Magellan RoadMate Photo Viewer enables you to view image files in JPG and BMP format, stored on the hard disk of  
your Magellan RoadMate or an optional storage card. In order to transfer files from your PC to the Magellan RoadMate, you  
must install the Magellan RoadMate Tools application (page 76) and have copied files onto your unit using the Magellan  
RoadMate Photo Manager (page 82).  
Press the MENU key on the unit (see page 4). Select the Photo Viewer  
.
The Photo Viewer screen will appear. The Photo viewer will show the Hard Disk and the storage  
card (if inserted).  
17.1 View Single Photo  
The next screen to appear shows the file structure of the hard disk. Select List Files  
.
Use the Navigation key or the Down arrow  
to highlight the photo you wish to view and  
select View.  
While viewing the image, double clicking on the image (that is tapping twice on the screen) will  
show the image in full screen. You can then cycle through the images by pressing left or right  
on the Navigation key.  
17.1.1 Previous Image (left arrow)  
Press the right arrow button to view the previous image in the folder. This button is grayed out (not functional) when viewing  
the first image in the folder.  
17.1.2 Zoom  
Press the Zoom button to reduce or enlarge the current photo. The top of the zoom menu shows the current zoom level.  
Select another zoom level from the list of presets. Select Best Fit to adjust the zoom to fit within the display boundaries;  
select Actual Size to display the image at 100%; select 25% to 150% to reduce or enlarge the image to the preset level.  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 17: Photo Viewer  
17.1.3 Slideshow  
Press the Slideshow button to cycle through all the photos in the Pictures folder automatically.  
17.1.4 Pan  
If you enlarge an image beyond the screen boundaries, press the Pan button to enable image scrolling. While enabled, you  
can drag the image in any direction to view other areas of the image. Press the Pan button again to disable Pan mode.  
17.1.5 Rotate Image  
Press the Rotate Image button to rotate the image 90° counterclockwise, 90° clockwise, or 180°.  
17.1.6 Next Image (right arrow)  
Press the right arrow button to view the next image in the folder. This button is grayed out (not functional) when viewing the  
last image in the folder.  
17.1.7 ESC  
Press ESC to return to the folder list.  
17.2 Manage Photos  
17.2.1 List View  
Press List view to show the files in a hierarchal list view.  
17.2.2 Thumbnail  
Press Thumbnail to show the files as thumbnails.  
17.2.3 Rename  
To change the name of the selected file or folder, press Rename.  
Use the backspace key (<-) to erase the name; and the keypad to enter a new name for your file. When you have finished,  
select OK.  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 17: Photo Viewer  
17.2.4 Properties  
To view information on the selected file or folder, press Properties. A thumbnail of the image will be displayed along with the  
width and height in pixels, the size, and the format (image type). When viewing the properties for folders, width, height, and  
format are not shown. Size shown is the combined size of all images in the selected folder.  
When you are finished viewing the properties, select OK.  
17.3 Tools  
17.3.1 Preferences  
General – The General preferences, you can set the default file view to either thumbnail or file  
list view.  
Slideshow – The slideshow preferences enable you to set the view properties, the sequence of  
photos, the transition between photos, and the duration between photos.  
Background – The background preferences enable you to set the color of the background behind the photo being viewed.  
17.3.2 Transfer Photos  
Select Transfer Photos to copy files or folders between your hard disk and an optional storage card.  
17.3.3 Delete Files  
Use the arrow keys to select the file or folder you wish to delete. Press the Delete button (trash can).  
A dialog box will appear asking to confirm your selection. Select Yes to delete the file.  
17.3.4 About  
This option will display the current version of the Photo Viewer software.  
90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
POI Categories  
The Magellan RoadMate POI database has 37 different categories. The icons will appear on the Map screen (if enabled):  
Restaurant  
Fast food, diners, and food marts  
Most financial services  
Bank/ATM  
Gas Station  
Roadside Assistance  
Hospital/Polyclinic  
Vehicle Services  
Airport  
Most fuel services  
Towing companies  
Most medical services  
Repair shops, tire stores, and oil changes  
International and Municipal airports  
Campgrounds, camping areas, and RV parks  
Car rental companies  
Camping & RV  
Car Rental  
Casino  
Gambling venues  
City Center  
The geographical center of a selected city  
Clothing retail stores  
Clothing  
Convention Center  
Major Convention Centers  
Schools, Colleges, and other learning  
institutions  
Education  
Emergency Services  
Entertainment  
Golf Course  
Police, FIre, and Emergency Rooms  
Movie theaters, live performance venues  
Private and public courses  
Grocery Store  
Hair & Beauty  
Health Care  
Major chains and local markets  
Salons and beauty parlors  
Doctors’ offices and pharmacies  
Nurseries and do-it-yourself centers  
Most overnight stay locations  
Docks and harbors  
Home & Garden  
Hotel or Motel  
Marina  
Misc. Services  
Nightlife  
Other services not categorized  
Dance halls, pubs, nightclubs  
Parking lots and garages  
Open Parking Area  
Parks  
County, regional, and local parks  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Professional Services  
Public Buildings  
Rest Area  
Business office locations  
Libraries, museums, and government buildings  
Rest stops along major highways  
Malls and other retail stores  
Most major ski resorts  
Shopping  
Ski Resorts  
Sports & Recreation  
Tourist Attraction  
Transportation  
Winery  
Stadiums, parks, lakes  
Places most visited by tourists  
Bus and train stations  
Vinyards and tasting locations  
Churches, temples, mosques  
Worship  
When selecting restaurants, you can further narrow the search by cuisine type such as French, Italian, Greek, Mexican, etc.  
PC Requirements  
•
•
•
•
•
•
IBM Compatible PC, Pentium or higher  
Microsoft ® WIndows® 2000 or XP  
128 MB RAM  
CD Drive for Software Installation  
DVD Drive for Map Upgrades  
USB Port  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
GPS Status Screen  
GPS STATUS Screen Structure-first page  
CH  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
11  
12  
13  
14  
PRN  
d1  
AZ  
d2  
EL  
d3  
SNR  
d4  
U/N  
c1  
d1  
d1  
d1  
d1  
d1  
d1  
d1  
d1  
d1  
d1  
d1  
d1  
d1  
d2  
d2  
d2  
d2  
d2  
d2  
d2  
d2  
d2  
d2  
d2  
d2  
d2  
d3  
d3  
d3  
d3  
d3  
d3  
d3  
d3  
d3  
d3  
d3  
d3  
d3  
d4  
d4  
d4  
d4  
d4  
d4  
d4  
d4  
d4  
d4  
d4  
d4  
d4  
c1  
c1  
c1  
c1  
c1  
c1  
c1  
c1  
c1  
c1  
c1  
c1  
c1  
It is ordered by the channel number from 1 to 12.  
Where:  
d1: Satellite PRN number, with “e” or “E” to the right means got ephemeris data, “v” or “V” to the right means got verified  
ephemeris data (double check). “E” or “V” also means got satellite time for this channel.  
d2: Azimuth, in degrees  
d3: Elevation angle, in degrees  
d4: SNR (signal to noise ratio), it is ratio-Hz, not dB unit  
c1: U – Used for position fix, U – Not used for position fix  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Bad fix code  
0 PVT_OK  
:good fix  
2 ILLEGAL_ALT: illegal altitude  
< -10km or > 17.5km  
4 POSITION_JUMP: too big position jump between two epoch (300 miles)  
5 ILLEGAL_VELOCITY_OR_ALT: max velocity 951mile  
7 TOO_BIG_ACCELERATION max 15m around 1.5g  
8 TOO_SMALL_ALTITUDE -10000 m  
9 TOO_BIG_ALTITUDE  
10 TOO_BIG_PDOP  
17,500 m  
max PDOP 50  
11 SATS_BELOW_MASK_ANGLE satellite elevation angle is below mask angle  
16 ILL_DEFINED_3D_MATRIX 3X3 matrix can not be inverted in 3D fix  
17 ILL_DEFINED_2D_MATRIX 2X2 matrix can not be inverted in 2D fix  
20 NO_SAT_TIME  
no satellite time  
no enough satellite for 2D or 3D fix  
23 NOT_ENOUGH_SATS  
24 CANNOT_SELECT_FIX_TYPE  
30 VELOCITY_2D_ONLY  
2 satellite fix only for velocity, no position fix  
31 BAD_VELOCITY_PDOP 50 too big pdop for velocity  
32 TOO_MANY_SATS_FOR_2D_VEL there are 4 or more satellites, but 2D fix provided  
51 WRONG_NUMSAT number of satellite for fix > 12 or less 2  
56 LOOP_3D_NOT_CONVERGING 3D initial fix is not convergent  
57 MILLISECOND_ERROR  
millisecond jump happened  
58 LOOP_2D_NOT_CONVERGING 2Dinitial fix is not convergent  
59 BAD_RANGE_CHITEST; range post-fix residuals chi-test failed  
60 BAD_DOPPLER_CHITEST doppler post-fix residuals chi-test failed  
61 OSC_DRIFT_ERR  
too much clock drift 60HZ for XO, 7.5HZ for TCXO  
62 BAD_DOPPLER_ERR too big Doppler errors 4m/s  
63 BIG_RANGE_RESID  
110m/40m depend on virtual ttagl/ DGPS factors  
64 BIG_DOPPLER_RESID 0.7m/s  
65 HUGE_RANGE_RESID 10km normal for postfit residuals for range  
66 HUGE_DOPPLER_RESID 100m/s normal for postfit residuals for doppler  
Usually, Bad code is 20 and 23. If fix is good, it would be 0.  
94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
GPS STATUS Screen Structure - second page  
Heading XXX (degree) Speeding XX.X (meter per second)  
Current Lat: DDD.DDDDD W/E (current latitude, degree)  
Current Long: DDD.DDDDD N/S (current longitude, degree)  
Current altitude XXXX (altitude in mean sea level meter) TTFF XXXXs (Time-To-First-Fix in second)  
#Satellite (U/T) XX/XX (the number of satellite used and tracked)  
PDOP XX.X  
VDOP XX.X  
TDOP XX.X  
HDOP XX.X  
FOMS P/V/H  
(Position Dilution Of Precision)  
(Vertical Dilution of Precision)  
(Time Dilution of Precision)  
(Horizontal Dilution of Precision)  
(Figures Of Merits for position, velocity and heading in map matching)  
UTC TIME MM/DD/YY HH:MM:SS(UTC time without local zone)  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Typical GPS STATUS Screen Display  
First Page  
CH  
PRN  
AZ  
EL  
SNR  
U/N  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
11  
12  
13  
14  
27V  
311  
54  
334  
U
U
U
N
U
U
U
U
N
N
N
N
N
N
03E  
13e  
20e  
31v  
01V  
28V  
08V  
02V  
84  
10  
72  
134  
122  
078  
079  
175  
119  
120  
220  
282  
046  
255  
325  
105  
255  
105  
29  
81  
06  
34  
53  
13  
29  
27  
12  
06  
13  
12  
13  
135  
204  
90  
179  
316  
152  
182  
173  
0
47  
34  
50  
63  
Second Page  
Heading 0  
Speed 0.0 m/s  
Current Lat: 34.10939 N  
Current Long:117.82599 W  
GPS Version:  
Current altitude 255 TTFF 116s  
#Satellite (U/T) 11/12  
PDOP 2.3  
VDOP 1.7  
TTFF 0.0  
HDOP 1.3  
FOMS P/V/H  
2
UTC TIME 08/16/2004 22:56:53  
96  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Frequently Asked Questions  
Why is my street not showing up on the map?  
The Magellan RoadMate uses the most current available map data. Chances are, your street is in a new housing development  
or the street is new. Map updates are made available about twice per year.  
I know there is a gas station on this street corner, why is there not icon for it on the map?  
Check your POI settings and make sure you have the necessary POI checked to make it visible on the map. see “POI  
Selection” on page 55.  
The Magellan RoadMate uses the latest POI data available. Chances are the POI you are looking for is relatively new and has  
not been added to the database. If this is not the case, it may have been overlooked or changed since the POI database was  
created. You can add custom POIs to your Magellan RoadMate to make up for those you route to often. see “Chapter 13:  
Magellan RoadMate POI Manager” on page 77, and “Custom POIs” on page 55.  
The GPS signal is weak. What’s going on?  
You may be driving through an area that has tall buildings or trees, or a canyon, or a tunnel. These conditions may interfere  
with satellite signals. Wait a few moments and the signal should get better as more satellites are acquired. Or, you may need  
to reposition you antenna. Rotate the antenna upward slightly and wait a moment. If the signal does not improve, continue  
to rotate the antenna. If the problem persists, there may be a problem with the antenna. Contact Technical Support.  
Why is an address I know I routed to not in the Previous Destinations list?  
THe Previous Destinations list stores the last 50 places you routed to. When you get to number 51, the first destination on  
the list is removed and each successive destination is moved up.  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Learning Resources Games LER 7024 User Manual
Lennox Hearth Electric Heater EBVI25 User Manual
Lux Products Thermostat PSD111 User Manual
Magnavox DVD VCR Combo MDV 530 VR User Manual
Makita Sander BO455 User Manual
Makita Sander BO6010 User Manual
Manhattan Computer Products Computer Hardware 160391 User Manual
Marantz Stereo Receiver SR6400 User Manual
M Audio Network Card Audiophile 2496 User Manual
Memorex MP3 Player MB002 User Manual