Mackie Speaker System SA1532Z User Manual

SA1532Z

3-WAY ACTIVE

LOUDSPEAKER SYSTEM

USER’S MANUAL

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Thank you for choosing Mackie’s active sound reinforce- A male XLR Thru jack is provided for daisy-chaining the

ment loudspeaker systems.

signal to additional SA1532z cabinets.

The SA1532z is a high-efﬁciency, extreme output,

horn-loaded, 3-way, wide-dispersion, active sound

reinforcement system. It features a one-piece 90º x 40º

horn, which includes both the mid- and high-frequency

Three built-in power ampliﬁers provide 100 watts rms

each for the mid-frequency and high-frequency drivers,

and 1100 watts rms for the low-frequency driver. The

ampliﬁer modules sit on a mammoth aluminum heatsink

sections in a proprietary optimized Wavefront™ design. that eliminates the need for fans. A tremendous beneﬁt

Unlike typical mid/high horn designs, the high-frequency of having the ampliﬁers located within the loudspeaker

section is positioned to ﬁre down into the 6-inch mid-

cabinet is that the SA1532z functions as a system, opti-

range’s dispersion pattern. This creates a focused, single mizing acoustic, electronic, and mechanical designs to

wave front with excellent phase and power response

characteristics. The resulting 90º x 40º dispersion pat-

tern provides a very open, natural sound at extreme

output levels.

achieve the highest level of performance and value.

The rear mounted ampliﬁer assembly features

separate signal and AC power panels separated by the

heatsink. The signal input panel contains:

• an input XLR and loop-through XLR

• a volume level control

The 6-inch neodymium mid-range transducer oper-

ates between 700 Hz and 3000 Hz, eliminating the place-

ment of a crossover point in the middle of critical voice

frequencies. Frequencies above 3000 Hz are reproduced

by a 1.75-inch neodymium compression driver. The low

frequencies are produced by two high-output 15-inch

woofers.

• Power ON indicator

• Signal Present indicator

• Limit indicator

• Thermal Protection indicator

The cabinet is constructed using both 18 mm multi-

layered plywood and pressure injected structural resin.

A carrying handle is integrated into each side for easy

loading and transport.

Connecting and setting up the SA1532z is a breeze. It

accepts a line-level signal via a female XLR input jack.

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS .................................................................................................2

INTRODUCTION ........................................................................................................................................3

REAR PANEL DESCRIPTION ....................................................................................................................4

HOOKUP DIAGRAM ..................................................................................................................................5

CONNECTIONS ..........................................................................................................................................5

PLACEMENT ................................................................................................................................................5

Room Acoustics .................................................................................................................................................................. 6

THERMAL CONSIDERATIONS ............................................................................................................... 6

AC POWER .................................................................................................................................................. 6

SERVICE INFORMATION ..........................................................................................................................7

Warranty Service ................................................................................................................................................................7

Troubleshooting .................................................................................................................................................................7

Repair .................................................................................................................................................................................... 8

CARE AND MAINTENANCE .................................................................................................................... 8

SA1532z SPECIFICATIONS ........................................................................................................................ 9

SA1532z LIMITED WARRANTY ...............................................................................................................11

Don’t forget to visit our website at www.mackie.com

for more information about this and other Mackie products.

Part No. 0013863 Rev. A 12/04

Download from Www.Somanuals.com. All Manuals Search And Download.

REAR PANEL DESCRIPTION

1. MAIN INPUT

This is a female XLR-type connector that

accepts a balanced line-level signal from a

mixing console or other signal source.

��

SA1532Z

ACTIVE SOUND REINFORCEMENT

SPEAKER SYSTEM

2. LOOP OUT

��

This is a male XLR-type connector that

produces exactly the same signal that is

connected to the MAIN INPUT jack. Use it to

daisy-chain several SA1532z's together off the

same signal source.

��

7. THERMAL Indicator

There is also a thermal protection circuit that mon-

itors the internal temperature of the ampliﬁers and

heatsink. If the temperature should exceed a safe oper-

ating level, this indicator lights and the signal is muted to

allow the ampliﬁers to cool. When the temperature cools

to a safe level once again, the thermal protection circuit

deactivates and normal operation continues.

3. Level Control

This controls the overall signal level at the input to

the built-in power ampliﬁers. It ranges from –15 dB to

+5 dB of gain. The center detent is 0 dB (unity gain).

4. Power ON Indicator

Note: Activation of the thermal protection circuit is

an indication that you should take steps to avoid con-

tinued thermal problems. See “Thermal Considerations”

on page 6.

When the POWER switch is turned on, and the

linecord is connected to an active AC power supply, this

indicator lights green to let you know that you’re ready

to rock and roll. The cool blue LED on the front of the

cabinet works in the same way.

8. POWER Switch

5. SIGNAL Present Indicator

Use this switch to turn the SA1532z on and off. Make

sure the level control is turned down before you turn it

on.

This LED illuminates whenever there is a signal pres-

ent at the MAIN INPUT connector on the rear panel.

It senses the signal just after the level control, so if

the level control is turned down, the SIGNAL Present

indicator turns off.

9. AC Receptacle

This is where you connect the AC linecord to provide

AC power to the SA1532z’s built-in power ampliﬁers.

Plug the linecord into an AC socket properly conﬁgured

for your particular model.

6. LIMIT Indicator

The SA1532z has a built-in limiter that prevents the

ampliﬁer outputs from clipping or overdriving

the transducers. The LIMIT indicator lights

when the limiter is activated. It's okay for the

LIMIT indicator to blink occasionally, but if it

blinks frequently or lights continuously, turn

down the level control until the LIMIT indica-

tor only blinks occasionally.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

HOOKUP DIAGRAM

To Next

Speaker

To Next

Speaker

��

SA1532Z

ACTIVE SOUND REINFORCEMENT

SPEAKER SYSTEM

SA1532Z

ACTIVE SOUND REINFORCEMENT

SPEAKER SYSTEM

SA1532Z

ACTIVE SOUND REINFORCEMENT

SPEAKER SYSTEM

SA1532Z

��

ACTIVE SOUND REINFORCEMENT

SPEAKER SYSTEM

��

Left

Right

Line level

Output

Line level

Output

1202-VLZPRO

Mixer or

Preamplifier

DAISY-CHAINING MULTIPLE SA1532z'S

The LOOP OUT jack is wired straight from the MAIN

INPUT connector — there is no electronic circuitry

between — so the signal coming out of the LOOP OUT

jack is exactly the same as the signal going in.

CONNECTIONS

The SA1532z has one female XLR input that accepts

a balanced line-level signal. When connecting a balanced

signal, be sure it’s wired per AES (Audio Engineering

Society) standards:

PLACEMENT

XLR

The SA1532z speaker is designed to sit on the ﬂoor or

stage.

Hot (+)

Cold (–)

Pin 2

Pin 3

WARNING: The cabinet has no rig-

ging points and is not suitable for rig-

ging. NEVER attempt to suspend the

SA1532z by its handles. The SA1532z

should never be pole-mounted.

Shield (Ground) Pin 1

You can create a horizontal array by placing the cabi-

nets side-by-side. However, you should have a good un-

derstanding of the relationship between the splay angle

(the angle between the facing sides of the cabinets),

the on-axis power, and frequency cancellation effects

between cabinets.

When two cabinets are placed side-by-side, the actual

splay angle is 20º (determined by a 10º angle on each

cabinet side). As the splay angle increases toward the

angle of horizontal coverage (90º for the SA1532z), the

on-axis power decreases, but the frequency response

becomes smoother as the comb-ﬁltering effects (caused

by the interaction in the area of double-coverage)

decrease.

Balanced XLR Connectors

There is also a male XLR connector labeled LOOP

OUT. This is also wired according to the above AES

standard.

The LOOP OUT connector allows you to connect

more than one SA1532z to your system. Simply plug the

signal source (i.e., mixer output) into the ﬁrst MAIN

INPUT jack, and patch that speaker’s LOOP OUT jack

to the next MAIN INPUT jack, and so on, daisy-chaining

multiple speakers.

As with any powered components,

protect them from moisture. If you

are setting them up outdoors, make

sure they are under cover if you

expect rain.

Download from Www.Somanuals.com. All Manuals Search And Download.

Room Acoustics

THERMAL CONSIDERATIONS

The SA1532z loudspeakers are designed to sound as

neutral as possible; that is, to reproduce the input signal

as accurately as possible.

The SA1532z has three powerful built-in ampliﬁers

capable of producing a combined 1300 watts of power.

As ampliﬁers produce heat, it is important to dissipate

the heat as quickly as possible. This results in increased

reliability and longevity for the ampliﬁer.

Room acoustics play a crucial role in the overall per-

formance of a sound system. Here are some additional

placement tips to help overcome some typical room

problems that might arise:

The ampliﬁer module is mounted on a large heatsink,

which is cooled by convection where cool air is drawn

through it’s ﬁns, carrying the heat away. In order for this

convection cooling to work efﬁciently, it is important

to provide adequate airspace behind the loudspeaker.

When you position the SA1532z, we recommend leaving

at least six inches of air space behind it.

•

Avoid placing loudspeakers in the corners of a

room. This increases the low frequency output and

can cause the sound to be muddy and indistinct.

•

Avoid placing loudspeakers against a wall. This, too,

increases the low frequency output, though not as

much as corner placement. However, if you do need

to reinforce the low frequencies, this is a good way

to do it.

In the unlikely event of the ampliﬁer overheating, a

built-in thermal switch will activate, which mutes the

signal and lights the THERMAL LED. When the ampliﬁ-

er has cooled down to a safe operating temperature, the

thermal switch resets itself, and the SA1532z resumes

normal operation.

•

Avoid placing the speakers directly on a hollow

stage ﬂoor. A hollow stage can resonate at certain

frequencies, causing peaks and dips in the fre-

quency response of the room. It’s better to place the

loudspeakers on a sturdy table or stand designed to

handle the weight of the SA1532z.

If the thermal switch activates frequently, try turning

down the level control a notch or two on the mixing con-

sole (or the back of the SA1532z) to avoid overheating

the ampliﬁer.

Position the loudspeakers so the high-frequency

drivers are 2 to 4 feet above ear level for the audience

(make allowances for a standing/dancing in the aisles

audience). High frequencies are highly directional

and tend to be absorbed much easier than lower

frequencies. By providing direct line-of-sight from the

loudspeakers to the audience, you increase the over-

all brightness and intelligibility of the sound system.

If the temperature in the room is too high, it could

cause the ampliﬁer to overheat. In this case, you should

try aiming a fan at the rear panel to move more air

through the heatsink ﬁns.

AC POWER

•

Highly reverberant rooms, like many gymnasiums

and auditoriums, are a nightmare for sound system

intelligibility. Multiple reﬂections off the hard walls,

ceiling, and ﬂoor play havoc with the sound. Depend-

ing on the situation, you may be able to take some

steps to minimize the reﬂections, such as putting

carpeting on the ﬂoors, closing draperies to cover

large glass windows, or hanging tapestries or other

materials on the walls to absorb some of the sound.

Be sure the SA1532z is plugged into an outlet that

is able to supply the correct voltage speciﬁed for your

model. If the voltage should drop below 97% of the spec-

iﬁed line voltage, the built-in ampliﬁers will no longer

be able to supply rated power. (They will continue to

operate down to 80% of the rated line voltage, but won’t

reach full power, resulting in lower headroom.)

Be sure the electrical service can supply enough am-

perage for all the components connected to it.

However, in most cases, these remedies are not possi-

ble or practical. So what do you do? Making the sound

system louder generally doesn’t work because the

reﬂections become louder, too. The best approach is to

provide as much direct sound coverage to the audience

as possible. The farther away you are from the speaker,

the more prominent will be the reﬂected sound.

We recommend that a stiff (robust) supply of AC

power be used because the ampliﬁers place high cur-

rent demands on the AC line. The more power that is

available on the line, the louder the speakers will play

and the more peak output power will be available for

cleaner, punchier bass. A suspected problem of “poor

bass performance” is often caused by a weak AC supply

to the ampliﬁers.

Use more speakers strategically placed so they are

closer to the back of the audience. If the distance

between the front and back speakers is more than

about 100 feet, you should use a delay processor to

time-align the sound. (Since sound travels about

1 foot per millisecond, it takes about 1/10 of a

second to travel 100 feet.)

Never remove the ground pin on

the power cord of the SA1532z or

any other component. This is very

dangerous.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE INFORMATION

Warranty Service

Poor bass performance

•

Check the polarity of the connections between the

mixer and the loudspeakers. You may have your

positive and negative connections reversed at one

end of one cable, causing one loudspeaker to be

out-of-phase.

Details concerning warranty service are spelled out

on page 11 of this manual.

If you think your loudspeaker has a problem, please do

everything you can to conﬁrm it before calling for service,

including reading through the following Troubleshooting

section. Doing so might save you from being deprived of

your Mackie loudspeaker.

Poor sound

•

Is it loud and distorted? Make sure that you’re not

overdriving a stage in the signal chain. Verify that

all level controls are set properly.

Of all Mackie products returned for service (which is

hardly any at all), many are coded “CND” — Could Not

Duplicate— which usually means the problem lay some-

where else in the system. The following troubleshooting

tips may sound obvious, but here are some things you

can check:

•

Is the input connector plugged completely into the

jack? Be sure all connections are secure. It’s a good

idea to periodically clean all electrical connections

with a non-lubricating electrical contact cleaner.

Troubleshooting

Noise

•

Make sure all connections to the active loudspeak-

ers are good and sound.

No power

•

Make sure none of the signal cables are routed near

AC cables, power transformers, or other EMI-induc-

ing devices.

•

Our favorite question: Is it plugged in? Make sure

the AC outlet is live (check with a tester or lamp).

Our next favorite question: Is the POWER switch

on? If not, try turning it on.

•

Is there a light dimmer or other SCR-based device

on the same AC circuit as the SA1532z? Use an AC

line ﬁlter or plug the SA1532z into a different AC

circuit.

Is the POWER LED on the rear panel glowing

green? If not, make sure the AC outlet is live. If so,

refer to “No sound” below.

•

The internal AC line fuse may be blown. This is not

a user serviceable part. If you suspect the AC line

fuse is blown, please see the "Repair" section next.

Hum

•

Try disconnecting the cable connected to the MAIN

INPUT jack. If the noise disappears, it could be

a “ground loop,” rather than a problem with the

SA1532z. Try some of the following troubleshooting

ideas:

No sound

•

Is the input level control for the input source

turned all the way down? Verify that all the volume

controls in the system are properly adjusted.

◊

Use balanced connections throughout your

system for the best noise rejection.

•

Is the signal source working (and making union

scale)? Make sure the connecting cables are in good

repair and securely connected at both ends. Make

sure the output volume (gain) control on the mixing

console is turned up sufﬁciently to drive the inputs of

the speaker.

◊

Whenever possible, plug all the audio equip-

ment’s linecords into outlets which share a common

ground. The distance between the outlets and the

common ground should be as short as possible.

•

Make sure the mixer does not have a Mute on or a

Processor loop engaged. If you ﬁnd something like

this, make sure the volume/gain is turned down

before disengaging the offending switch.

Is the THERMAL indicator lit red on the rear panel?

Make sure there is at least six inches of free space

behind the SA1532z.

Download from Www.Somanuals.com. All Manuals Search And Download.

Repair

Service for Mackie products is available at a factory-

authorized service center. Service for Mackie products

outside the United States can be obtained through local

dealers or distributors.

8. We’ll try to ﬁx the loudspeaker within ﬁve business

days. Once it is repaired, we’ll ship it back the same

way in which it was received. This paragraph does

not necessarily apply to non-warranty service.

If your SA1532z needs service, please follow these

instructions:

Note: You must have a sales receipt from an Autho-

rized Mackie Dealer to qualify for a warranty repair.

1. Review the preceding troubleshooting suggestions.

Please.

2. Call Tech Support at 1-800-898-3211, 7 am to 5 pm

PST, to explain the problem in detail. They will ask

you all sorts of impertinent questions in the hope

of sorting out the problem. If it appears that the

SA1532z needs repair, you will be given a Service

Request Number. Have your loudspeaker’s serial

number ready. You must have a Service Request

Number before you can obtain service at a factory-

authorized service center.

CARE AND MAINTENANCE

Your Mackie loudspeakers will provide many years of

reliable service if you follow these guidelines:

Avoid exposing the loudspeakers to

moisture. If they are set up out-

doors, be sure they are under cover

if you expect rain.

3. Keep this user’s manual and the detachable line-

cord. We don’t need them to repair the loudspeaker.

•

Avoid exposure to extreme cold (below freezing

temperatures). If you must operate the loud-

speakers in a cold environment, warm up the voice

coils slowly by sending a low-level signal through

them for about 15 minutes prior to high-power

operation.

4. Pack the loudspeaker in its original packaging,

including protective wrap, endcaps, and box. This

is VERY IMPORTANT. When you call for the Service

Request Number, please let Tech Support know if

you need new packaging. Mackie is not responsible

for any damage that occurs due to non-factory

packaging.

Use a slighty damp cloth with a mild soap solution

to clean the cabinets. Only do this when the power

is turned off. Avoid getting moisture into any of the

openings of the cabinet, particularly where the driv-

ers are located.

5. Include a legible note stating your name, shipping

address (no P.O. boxes), daytime phone number,

Service Request Number, and a detailed description

of the problem, including how we can duplicate it.

6. Write the Service Request Number in BIG

PRINT on top of the box. Product shipped with-

out the Service Request Number will be refused.

7. Tech Support will tell you where to ship the loud-

speaker for repair. We suggest insurance for all

forms of cartage.

Need Help?

You can reach a technical support representative

Monday through Friday

from 7 AM to 5 PM PST at:

1-800-898-3211

After hours, visit www.mackie.com and click Support,

or email us at: [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

SA1532z SPECIFICATIONS

Acoustic Performance

Safety Features

Input Protection

Low frequency dynamic bass

protection, rms limiting, power

supply and ampliﬁer thermal

protection

Frequency Range (–10 dB)

38 Hz–20 kHz

Frequency Response (–3 dB)

47 Hz–18 kHz

Horizonal Coverage Angle (–6 dB)

90º averaged 2 kHz to 10 kHz

Vertical Coverage Angle (–6 dB)

40º averaged 2 kHz to 10 kHz

Directivity Factor; DI (Q)

11.1 (12.9) averaged 2k Hz to 10 kHz

Max SPL long-term 135 dB @ 1m

Display LEDs

Power ON, Signal Present, Limit,

Thermal (cool down auto-reset)

Construction Features

Basic Design

Material

Finish

Trapezoidal, 10º sides

13-ply Baltic birch, resin end caps

Wear-resistant textured black

PVC vinyl

One on each side, one top, one bottom

Perforated metal with weather-

resistant coating

Max SPL peak

138 dB @ 1m

Crossover Points

700 Hz, 3000 Hz

Handles

Grille

Input/Output

Input Type

Input Impedance

Loop-Through

Female XLR Balanced/Unbalanced

50 kohms balanced

Male XLR Balanced/Unbalanced

(parallel with input)

Physical Properties

Height

50.0 in/127.0 cm

19.1 in/48.5 cm

13.9 in/35.3 cm

18.1 in/46.0 cm

132 lb/60 kg

Level Control

Rotating knob (–15 to +5 dB),

center detent at 0 dB

Front Width

Rear Width

Depth

Weight

Mounting Methods

High-Frequency Section

Voice Coil Diameter 1.75 in/44 mm

Horn Exit Diameter 1.0 in/25 mm

Floor mount only.

The SA1532z should never be pole-mounted.

The cabinet has no rigging points and is not

suitable for ﬂying. Never attempt to suspend the

cabinet by its handles.

Phase Plug

3-slot optimized geometry

Diaphragm Material Titanium

Magnet Material

Neodymium

Mid-Frequency Section

Diameter

Phase Plug

6.0 in/152 mm

Optimized geometry

Disclaimer

Since we are always striving to make our products better by in-

corporating new and improved materials, components, and manufac-

turing methods, we reserve the right to change these speciﬁcations

at any time without notice.

Diaphragm Material Epoxy-reinforced cellulose

Magnet Material Neodymium

Low-Frequency Section

“Mackie” and the “Running Man” ﬁgure are registered trademarks

of LOUD Technologies Inc.

Number of Drivers

Woofer Diameter

15.0 in/381 mm

Voice Coil Diameter 3.0 in/75 mm

Diaphragm Material Epoxy-reinforced cellulose

All other brand names mentioned are trademarks or registered

trademarks of their respective holders, and are hereby acknowledged.

Magnet Material

Ferrite

Power Ampliﬁers

Low-Frequency Power Ampliﬁer

Rated Power

Rated THD

Design

1100 watts rms

< 0.03%

Class G, Hybrid

Mid and High-Frequency Power Ampliﬁers

Rated Power

Rated THD

Design

100 watts rms

< 0.03%

Class AB

Line Input Power

120V, 60Hz

Recommended Amperage Service:

20 amps

16 amps

Europe

230V, 50Hz

Recommended Amperage Service:

AC Connector

3-pin IEC 250 VAC

Download from Www.Somanuals.com. All Manuals Search And Download.

SA1532z Frequency Response On-Axis

��

�

��

SA1532z Beamwidth vs. Frequency

SA1532z Directivity vs. Frequency

��

100

��

�

100

1000

10000 20000

��

Frequency (Hz)

��

SA1532z Dimensions

��

SA1532Z

ACTIVE SOUND REINFORCEMENT

SPEAKER SYSTEM

��

�

��

50.0 in/

13.9 in/

127.0 cm

35.3 cm

��

�

��

�

��

�

��

18.1 in/

46.0 cm

19.1 in/

48.5 cm

19.1 in/

48.5 cm

Download from Www.Somanuals.com. All Manuals Search And Download.

SA1532z LIMITED WARRANTY

Please keep your sales receipt in a safe place.

A. LOUD Technologies Inc. warrants all materials,

workmanship and proper operation of this product for a

period of ﬁve years from the original date of purchase with

the following exception: warranty on all its loudspeaker

components including woofers and compression drivers

are only warranted for two years. If any defects are found

in the materials or workmanship or if the product fails to

function properly during the applicable warranty period,

LOUD Technologies, at its option, will repair or replace the

product. This warranty applies only to equipment sold

and delivered within the U.S. by LOUD Technologies

Inc. or its authorized dealers.

F. Any products returned to one of the LOUD Technologies

factory-authorized service centers and deemed eligible for

repair or replacement under the terms of this warranty will

be repaired or replaced within thirty days of receipt. LOUD

Technologies and its authorized service centers may use

refurbished parts for repair or replacement of any product.

Products returned to LOUD Technologies that do not meet

the terms of this Warranty will be not be repaired unless

payment is received for labor, materials, return freight,

and insurance. Products repaired under warranty will be

returned freight prepaid by LOUD Technologies to any

location within the boundaries of the USA.

B. Failure to register online or return the product

G. LOUD Technologies warrants all repairs performed

for 90 days or for the remainder of the warranty period.

This warranty does not extend to damage resulting from

improper installation, misuse, neglect or abuse, or to

exterior appearance. This warranty is recognized only if

the inspection seals and serial number on the unit have not

been defaced or removed.

registration card will not void the ﬁve-year warranty.

C. Service and repairs of Mackie products are to be

performed only at a factory-authorized facility (see D

below). Unauthorized service, repairs, or modiﬁcation will

void this warranty. To obtain repairs under warranty, you

must have a copy of your sales receipt from the authorized

Mackie dealer where you purchased the product. It is

necessary to establish purchase date and determine whether

your Mackie product is within the warranty period.

H. LOUD Technologies assumes no responsibility for the

quality or timeliness of repairs performed by an authorized

service center.

D. To obtain factory-authorized service:

I. This warranty is extended to the original purchaser and

to anyone who may subsequently purchase this product

within the applicable warranty period. A copy of the

original sales receipt is required to obtain warranty repairs.

1. Call Mackie Technical Support at 800/898-3211,

7 AM to 5 PM Monday through Friday (Paciﬁc Time)

to get a Service Request Number. Products returned

without a Service Request Number will be refused.

J. This is your sole warranty. LOUD Technologies does

not authorize any third party, including any dealer or

sales representative, to assume any liability on behalf of

LOUD Technologies or to make any warranty for LOUD

Technologies Inc.

2. Pack the product in its original shipping carton. Also

include a note explaining exactly how to duplicate the

problem, a copy of the sales receipt with price and date

showing, and your return street address (no P.O. boxes

or route numbers, please!). If we cannot duplicate the

problem or establish the starting date of your Limited

Warranty, we may, at our option, charge for service time.

K. THE WARRANTY GIVEN ON THIS PAGE IS THE SOLE

WARRANTY GIVEN BY LOUD TECHNOLOGIES INC.

AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

AND IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. THE WARRANTY GIVEN ON THIS PAGE

SHALL BE STRICTLY LIMITED IN DURATION TO FIVE

YEARS FROM THE DATE OF ORIGINAL PURCHASE

FROM AN AUTHORIZED MACKIE DEALER. UPON

EXPIRATION OF THE APPLICABLE WARRANTY PERIOD,

LOUD TECHNOLOGIES INC. SHALL HAVE NO FURTHER

WARRANTY OBLIGATION OF ANY KIND. LOUD

TECHNOLOGIES INC. SHALL NOT BE LIABLE FOR ANY

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES

THAT MAY RESULT FROM ANY DEFECT IN THE MACKIE

PRODUCT OR ANY WARRANTY CLAIM. Some states do

not allow exclusion or limitation of incidental, special,

or consequential damages or a limitation on how long

warranties last, so some of the above limitations and

exclusions may not apply to you. This warranty provides

speciﬁc legal rights and you may have other rights which

vary from state to state.

3. Ship the product in its original shipping carton,

freight prepaid to the authorized service center. The

address of your closest authorized service center will be

given to you by Technical Support.

IMPORTANT: Make sure that the Service Request

Number is plainly written on the shipping carton.

E. LOUD Technologies reserves the right to inspect

any products that may be the subject of any warranty

claims before repair or replacement is carried out. LOUD

Technologies may, at our option, require proof of the

original date of purchase in the form of a dated copy

of the original dealer’s invoice or sales receipt. Final

determination of warranty coverage lies solely with LOUD

Technologies.

Download from Www.Somanuals.com. All Manuals Search And Download.

16220 Wood-Red Road NE • Woodinville, WA 98072 • USA

US and Canada: 800.898.3211

Europe, Asia, Central and South America: 425.487.4333

Middle East and Africa: 31.20.654.4000

Fax: 425.487.4337 • www.mackie.com

E-mail: [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

KWC Plumbing Product K28H12000099 User Manual
Legacy Car Audio Car Stereo System LCD87DFX User Manual
Lenovo Computer Hardware 41N3005 User Manual
LG Electronics Car Satellite TV System 32LP645H User Manual
Liebherr Refrigerator 7085400 01 User Manual
Lightolier Work Light MHCR User Manual
LST Smoke Alarm ECO1003 User Manual
Lumens Technology Camera Accessories PS760 User Manual
Makita Cordless Drill 60921 User Manual
Melissa Blender 246 008 User Manual