MGE UPS Systems Power Supply GES 102L User Manual

Always “On” UPS Systems Inc.  
GES L-Series – Single Phase Input, Single Phase Output  
Uninterruptible Power Supply  
USER MANUAL  
Version 1.4  
GES-801L, GES-102L, GES-152L, GES-202L, GES-302L  
Line Interactive (True Sine Wave):  
800VA, 1000VA, 1500VA, 2000VA, 3000VA  
Extended Run-Time Battery Banks  
Available on All Models  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
SAVE THESE INSTRUCTIONS  
This manual contains important instructions for the GES-801L, GES-102L, GES-152L, GES-202L,  
GES-302L and should be followed during installation and maintenance of the UPS and batteries.  
The UPS contains voltages that are potentially hazardous. Please contact our dealers or qualified  
personnel for service.  
Servicing of the batteries should be performed or supervised by personnel knowledgeable with batteries  
and the required precautions. Keep unauthorized personnel away from batteries.  
When replacing batteries, replace with the same model number, type and rating.  
CAUTION: Do not dispose of the batteries in a fire. The batteries may explode.  
CAUTION: Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes.  
It may be toxic.  
CAUTION: A battery can present a risk of electrical shock and high short circuit current. The  
following precautions should be observed when working on or with the batteries.  
Remove watches, rings, or other metal objects.  
Use tools with insulated handles.  
Wear rubber gloves and boots.  
Do not lay tools or metal parts on top of batteries.  
Disconnect charging source prior to connecting or disconnecting battery terminals.  
Determine if the batteries are inadvertently grounded. If inadvertently grounded, remove source of  
ground. Contact with any part of a grounded battery can result in electric shock. The likelihood of a  
shock will be reduced if grounds are removed during installation and maintenance (applicable to a UPS  
and a remote battery supply not having a grounded supply circuit).  
CAUTION: To ensure the safety and performance of the UPS, never load the UPS with a hair dryer,  
heater, laser printer, Surge protector or other types of inductive loads.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
TABLE OF CONTENTS  
INTRODUCTION........................................................................................................................................ 5  
SAFETY INSTRUCTIONS......................................................................................................................... 6  
PRESENTATION ........................................................................................................................................ 7  
FRONT PANEL............................................................................................................................................. 7  
REAR PANEL............................................................................................................................................... 8  
INSTALLATION ....................................................................................................................................... 10  
UNPACKING AND INSPECTION................................................................................................................... 10  
PLACEMENT.............................................................................................................................................. 10  
CONNECT COMPUTER INTERFACE (OPTIONAL)......................................................................................... 10  
CONNECT EXTERNAL BATTERY BANK (OPTIONAL).................................................................................. 10  
CONNECT TO UTILITY............................................................................................................................... 10  
CHARGING THE BATTERY......................................................................................................................... 10  
CONNECTING THE LOADS ......................................................................................................................... 10  
CONNECTING THE TELEPHONE/MODEM/ETHERNET LINES ....................................................................... 11  
CHECK THE SITE WIRING FAULT INDICATOR............................................................................................ 11  
OPERATION.............................................................................................................................................. 12  
SWITCHING “ONTHE UPS...................................................................................................................... 12  
SWITCHING “OFFTHE UPS..................................................................................................................... 12  
SELF-TEST ................................................................................................................................................ 12  
SILENCE THE ALARM ............................................................................................................................... 12  
LOAD BAR GRAPH.................................................................................................................................... 12  
BATTERY CHARGE BAR GRAPH................................................................................................................ 13  
COLD START............................................................................................................................................. 13  
SHUTDOWN MODE.................................................................................................................................... 13  
AUDIBLE ALARM.................................................................................................................................... 13  
BACK-UP (SLOW ALARM)........................................................................................................................ 13  
LOW BATTERY (RAPID ALARM)............................................................................................................... 13  
OVERLOAD (CONTINUOUS ALARM).......................................................................................................... 13  
REPLACE BATTERY (CONTINUOUS ALARM)............................................................................................. 13  
SOFTWARE OPTIONS ............................................................................................................................ 14  
UPSILON 2000 SOFTWARE....................................................................................................................... 14  
INTERFACE KITS....................................................................................................................................... 14  
COMPUTER INTERFACE PORT ................................................................................................................... 15  
Open Collector (Dry Contact) Communication.................................................................................. 15  
RS-232 Communication ...................................................................................................................... 15  
BATTERY REPLACEMENT................................................................................................................... 16  
TROUBLESHOOTING............................................................................................................................. 17  
STORAGE .................................................................................................................................................. 18  
STORAGE CONDITIONS ............................................................................................................................. 18  
EXTENDED STORAGE................................................................................................................................ 18  
BATTERY BANK INSTALLATION....................................................................................................... 19  
SPECIFICATIONS.................................................................................................................................... 20  
CONTACT INFORMATION ................................................................................................................... 22  
ADDITIONAL PURCHASES OR UPGRADES.................................................................................................. 22  
QA / WARRANTY QUESTIONS .................................................................................................................. 22  
SOFTWARE QUESTIONS ............................................................................................................................ 22  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Introduction  
The L-Series is a Line Interactive UPS system that includes the newest and latest  
technology enhancements. The Line Interactive technology with AVR function (on-  
line voltage boost-up & buck-down) allows for a wide input voltage range of 90 to  
150VAC. The L-Series UPS is the ideal protection for microprocessor controlled  
loads. With the utility power connected, the charger begins to operate immediately,  
charging the battery. In the event of a blackout (or severe brownout) the UPS will  
automatically switch to back-up mode and maintain power to the load until the  
software shuts down the system and/or when the battery reaches a low voltage state.  
The Low Battery indicator will turn “On” if and when the battery needs replacement.  
Also included, with our UPS systems, is a cyclic self-testing function to verify both  
the operation of the UPS and the condition of the battery.  
In addition, the L-Series UPS provides advanced telephone line and Ethernet surge  
suppression through the modular connectors on the back panel.  
The Line Interactive UPS in conjunction with our monitoring software makes your  
UPS operate intelligently and provides you with total protection for all your loads.  
Note: Interference to radio/TV might occur in a particular installation. If this UPS  
causes interference to radio or television reception, which can be determined by  
turning the UPS off and on, the user is encouraged to try to correct the interference  
by one or more of following measures:  
1. Connect the equipment to an outlet on a circuit different from that to which the  
receiver is connected.  
2. Increase the separation between the equipment and the receiver.  
3. Reorientate the receiving antenna.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Safety Instructions  
The UPS has its own internal energy source (batteries), therefore the output receptacles may  
have electricity present even though the UPS is disconnected from the utility power.  
The DC voltage provided from the internal batteries are as follows:  
a)  
b)  
c)  
GES-801L  
GES-102L  
GES-152L  
24VDC  
24VDC  
36VDC  
d)  
e)  
GES-202L  
GES-302L  
48VDC  
48VDC  
Isolated Ground Wire refers to the bare wire connecting electrical equipment to ground. The  
isolated ground wire (green or green with yellow stripe) must meet national wire requirements.  
The power plug to connect with the UPS has to be equipped with a ground plug.  
The batteries must be replaced or serviced by qualified, knowledgeable, personnel.  
Replacement batteries must be the same type, quantity and configuration as the originals.  
To avoid explosions, keep open flame and other heat emitting sources away from batteries.  
Do not disassemble or damage the batteries. The electrolyte is toxic and especially harmful to  
the eyes and skin.  
The batteries contain high voltages and currents that are dangerous. To maintain secure  
operation and performance of the UPS, the user must exercise basic and regular maintenance.  
Please follow the precautions below:  
1. Do not remove the UPS cover unless authorized by factory. Removing the cover will void  
the warranty.  
2. The UPS can only be connected to a 2-pole/3 wire plug.  
3. Do not install the UPS in an environment with excessive humidity.  
4. Do not allow liquids or foreign objects to get inside the UPS.  
5. Allow for air circulation through the UPS. A minimum clearance of 10 cm is required on all  
sides.  
6. Do not load the UPS with appliances such as a hair dryer, heater, vacuum, kettle, etc.  
7. Keep the UPS away from direct sunlight and heat-emitting sources.  
8. Install the UPS as close as possible to the load for maximum protection.  
9. Storage Requirements  
a. Recharge the UPS batteries every 6 months for no less than 8 hours at a time.  
b. Under a high ambient temperature environment, recharge the UPS batteries every 3  
months for no less than 8 hours at a time  
10. High Voltage Risk:  
a. High voltages might exist between the battery terminal and the grounding system, if the  
battery circuit has not been disconnected from the UPS circuit. Please check this voltage  
before connecting.  
b. Disconnect the battery wires before proceeding with maintenance. High voltages may be  
present between the UPS internal components and batteries even after the input power is  
disconnected.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Presentation  
Front Panel  
1. POWER bar graph (BATTERY CHARGE/LINE VOLTAGE)  
This displays the present battery charge as a percentage of battery capacity. It also displays  
the utility line voltage.  
2. LOAD bar graph  
This displays the amount of power required by the load as a percentage.  
3. "OVERLOAD" indicator (RED LED)  
This LED lights when the load(s) connected to the UPS exceed the UPS's capacity. See  
Section 6.3 for solution to this problem.  
4. "BUCK AVR (Automatic Voltage Regulation)" indicator (YELLOW LED)  
This LED illuminates when the UPS is correcting for a high utility voltage condition. The  
load(s) receive normal 120VAC power.  
5. "ON/TEST" button  
With the UPS plugged in, press the ON/TEST button to turn on the UPS and power the loads.  
ON/TEST also activates the UPS's self-test and utility line voltage displays.  
6. "LINE NORMAL" indicator (GREEN LED)  
This LED illuminates when the line input voltage is normal.  
7. "OFF" button  
Press the OFF button to turn off the UPS and the load(s).  
8. "BACK UP" indicator (GREEN LED)  
This LED illuminates when the UPS is supplying battery power to the loads.  
9. "BOOST AVR (VOLTAGE BOOST)" indicator (YELLOW LED)  
The LED illuminates when the UPS is correcting for a low utility voltage condition. The  
load(s) receive normal power.  
10. "REPLACE BATTERY" indicator (RED LED)  
This LED illuminates when the UPS's batteries are no longer useful and must be replaced.  
Note: When replacing the batteries, disconnect the utility power then open the case. Take  
notice of the polarity before installing the new batteries to avoid a short.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Rear Panel  
11. TELEPHONE/MODEM/ETHERNET SURGE PROTECTION  
Surge protection for telephone line, modem line, and 10BaseT line to maintain a completely safe  
connection for INTERNET/INTRANET service.  
12. EXTERNAL BATTERY PACK CONNECTOR (optional)  
Allows for extended runtime.  
Caution: Use only factory supplied or authorized connecting cable for external battery  
pack!  
13. SNMP INTERFACE PORT (optional)  
This option will allow the UPS to be connected directly to a network and also allow for remote  
monitoring. Through the RS-232 communication port, the SNMP adapter makes your UPS  
become "SNMP manageable", and provides real time UPS and power status information for the  
network manager.  
Note: It's not necessary to use this option.  
Caution: Use only factory supplied or authorized SNMP monitoring kit.  
14. OUTPUT POWER RECEPTACLES  
Connect load(s) here.  
15. AC INPUT POWER RECEPTACLE  
Plug into properly rated outlet.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
16. INPUT CIRCUIT BREAKER  
It trips when the connected loads exceed the protected receptacle's capacity. The center plungers  
of the circuit breakers extend when tripped.  
17. SITE WIRING FAULT INDICATORS (RED LED)  
It illuminates when the UPS is connected to an improperly wired AC power outlet.  
Note: This device is available on 120 VAC model only.  
18. COMPUTER INTERFACE  
Provides both RS-232 and relay signal to support NOVELL, UNIX, DOS, WINDOWS and other  
operating systems.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Installation  
Unpacking and Inspection  
Examine the packaging for damage. Inform the carrier immediately if and/or when damage is  
noticed. Retain the packaging for future use.  
Placement  
Install the UPS in a protected area with adequate airflow and free of excessive dust. Do not  
operate the UPS where the temperature and humidity is outside the specified limits.  
Connect Computer Interface (optional)  
UPSilon 2000 (or selected option) and an interface kit can be used with this UPS. Use only kits  
supplied or approved by the manufacturer. If used, connect the interface cable to the 9 pin  
computer interface port on the back panel of the UPS (See Back Panel).  
Note: Computer interface connection is optional. The UPS works properly without a computer  
interface connection.  
Connect External Battery Bank (optional)  
Before connecting, make sure the external battery bank and the connector cable are compatible  
with this UPS.  
Note: External battery connection is not necessary. The UPS will work properly without an  
external battery bank connection.  
Caution: Use only factory supplied external battery connection cables!  
Connect to Utility  
Connect the AC input power connector (included) to utility power.  
Charging the Battery  
The UPS charges its battery whenever it is connected to utility power. For best results, charge  
the battery for 4 hours initially before connecting the load.  
Connecting the Loads  
Plug the loads into the output connectors on the rear of the UPS. To use the UPS as a master  
on/off switch, make sure all of the loads plugged into the UPS are switched on. Also available  
on these models is a surge-protected outlet where you can plug in your laser printer, plotter, etc.  
Note: Never connect a laser printer or plotter to a backup outlet with other computer  
equipment. A laser printer or plotter draws significantly more power on start-up than when  
idle, and will overload the UPS. If you wish to have battery backup on a laser printer or  
plotter you will need to increase the size of the UPS system.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Connecting the Telephone/Modem/Ethernet Lines  
Connect a telephone line, modem line, or 10BaseT line into the telephone/modem/Ethernet surge  
protection sockets on the back of the UPS. The RJ-45/RJ-11 modular sockets accept standard  
single line telephone connections and 10BaseT connectors. This connection will require another  
length cable.  
Note: This connection is optional. It is not necessary to use this with the UPS.  
Caution: The line current limiting feature could be rendered inoperable if improperly  
installed. Make sure that the line from the wall is plugged into the connector marked “IN”,  
and the device to be protected (telephone, modem, etc.) is plugged into the connector  
marked “OUT”.  
Caution: This surge protection device is for indoor use only, never install wiring during a  
lightning storm.  
Check the Site Wiring Fault Indicator  
After plugging in the load(s) and the UPS, check the site wiring fault indicator on the rear panel.  
It lights up if the UPS is plugged into an improperly wired AC power outlet. Wiring faults  
detected include ground, hot-neutral polarity reversal, and overloaded neutral circuit.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Operation  
Switching “On” the UPS  
With the UPS plugged in, press and hold the “ON/TEST” button for at least 1 second to switch  
the UPS on. The UPS will perform a self-test each time it is switched on.  
Note: When switched off, and still plugged into utility, the UPS maintains the battery charge  
and will respond to commands received through the computer interface port.  
Switching “Off” the UPS  
Press and hold the “OFF” button until the "LINE NORMAL" or "BACK UP" LED turns off. To  
full turn off UPS also unplug the utility cord from the UPS.  
Self-test  
The self-test verifies that both the operation of the UPS and the condition of the batteries are  
normal. Under normal operating power, push and hold the ON/TEST button for more than 1  
second and the UPS will perform a self-test function. During the self-test, the UPS will operate  
in back-up mode.  
Note: During the self-test, the UPS briefly operates the load(s) on battery power (the Back-Up  
LED turns on). If the UPS passes the self-test, it returns to on-line operation the Back-Up  
LED turns off and the Line Normal LED turns on steady. If the UPS fails the self-test it  
immediately returns to normal operation and the Replace Battery LED turns on. The loads  
are unaffected by the self-test. Recharge the battery overnight and perform the self-test again.  
If the Replace Battery LED is still on, ask our nearest dealer about replacing the batteries.  
Silence The Alarm  
In "Back-Up" mode, push and hold the “ON/TEST” button for more than 1 second to silence the  
audible alarm. This function is unavailable under "LOW BATTERY" or "Overload" conditions.  
Note: In Back-Up mode, the UPS can be automatically turned off if none of the connected  
loads are operating.  
Load Bar Graph  
This 5 LED display shows the power required by the load as a percentage of the UPS's rated  
capacity. For example: If three LEDs are lit, the load is drawing between 50% and 67% of the  
total capacity. If the UPS is overloaded, the overload LED lights and an alarm sounds.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Battery Charge Bar Graph  
This 5 LED display indicates the present charge of the UPS's batteries as a percentage of the total  
battery capacity. When all five LED’s are lit, the batteries are fully charged. When only two of  
the LED’s are lit, the batteries can supply less than two minutes of power to the load.  
Cold Start  
When the UPS is off, and there is no utility power, use the cold start feature to apply power to  
the loads from the UPS's battery. Press and hold the “ON/TEST” button until the UPS beeps.  
Shutdown Mode  
In shutdown mode the UPS stops supplying power to the load, and waits for the return of utility  
power. If there is no utility power present, external devices (e.g., servers) connected to the  
computer interface port can command the UPS to shutdown. This is normally done to preserve  
battery capacity. The UPS will scroll the front panel indicators sequentially in shutdown mode.  
Audible Alarm  
Back-Up (Slow Alarm)  
When in back-up mode, the Yellow LED illuminates and the UPS sounds an audible alarm. The  
alarm stops when the UPS returns to line normal operation. Press the On/Off/Test/Silence  
Button during back-up mode to silence the beeping.  
Low Battery (Rapid Alarm)  
In back-up mode, when the battery energy runs low, the UPS beeps rapidly until the UPS shuts  
down from battery exhaustion or returns to line normal operation.  
Overload (Continuous Alarm)  
When the UPS is overloaded (the connected load exceeds the maximum rated capacity of the  
UPS) the UPS sounds a continuous alarm to warn of an overload condition. Disconnect non-  
essential loads until the UPS stop the alarm, this will eliminate the overload.  
Replace Battery (Continuous Alarm)  
The UPS emits continuous beeps and the REPLACE BATTERY LED illuminates if the battery  
fails the self-test. See replace battery section for battery replacement or call your dealer for  
service.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Software Options  
UPSilon 2000 Software  
The UPSilon 2000 software utilizes standard RS-232 interface to perform monitoring functions,  
and provides an orderly shutdown of a computer system in the event of power failure. Moreover,  
UPSilon 2000 displays all the diagnostic symptoms through a graphical interface, such as  
Voltage, Frequency, Battery Level, etc.  
The software is available for DOS, Windows 3.x, Windows 95/98/00 & Windows NT V3.5 or  
later, FreeBSD, Linex, Novell and more.  
Interface Kits  
A series of interface kits are available for various operating systems that provide UPS  
monitoring. Each interface kit includes the special interface cable required to convert status  
signals from the UPS into signals that the individual operating system will recognize. The  
interface cable at the UPS side must be connected to the REMOTE PORT, at the computer side it  
can be connected to either COM1 or COM2. For other installation instructions and powerful  
features please refer to READ ME file included within the software.  
Caution: Use only factory supplied or authorized UPS monitoring kits!  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Computer Interface Port  
The computer interface port has the following characteristics:  
The communication port on the back of the UPS may be connected to a host computer. This port  
allows the computer to monitor the status of the UPS and control the operation of the UPS. Its  
major functions include the following:  
1. The ability to broadcast a warning when the power fails.  
2. The ability to close any open files before the battery reserves are exhausted.  
3. The ability to turn off the UPS.  
4. The ability to make the UPS perform a self-test.  
Some computers are equipped with a serial connector to link with the communication port, in  
some cases a special plug-in card may be needed.  
Open Collector (Dry Contact) Communication  
1. Pin 5 and 2 are open collector outputs that must be pulled up to a common referenced supply  
no greater than +40VDC.  
2. The transistors are capable of a maximum non-conductive load of 25mADC, use pin 4 as the  
common.  
3. Pin 5 generates a High to Low signal when the battery inside the UPS has less than 5 minutes  
back up time left.  
4. Pin 2 generates a High to Low signal when the line has failed.  
5. Pin 6 will shut down the UPS is a high is sustained for 0.36 seconds.  
RS-232 Communication  
6. Pin 6 is the RS-232 data input from computer (RX)  
7. Pin 9 is the RS-232 data output to computer (TX).  
8. Pin 7 is the common or computer ground  
NOTE:  
1. Switch rating +40V, 25mADC non-inductive.  
2. Pin 7 should be connected to computer ground only.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Battery Replacement  
Your batteries should run anywhere from 3-5 years before they need to be replaced.  
Please follow the instructions below for easy, trouble free, battery replacement.  
1. Turn the UPS off (follow procedure previously mentioned)  
2. Unplug the UPS from utility power source and disconnect all connected loads.  
3. Disconnect AC power cord from unit.  
4. Using a phillips screw driver, unscrew the screws holding the top of the unit to the  
bottom. Put screws in a safe place for reconnection.  
5. Carefully lift top cover off and place it to the side. The connecting wires and  
electronics will be exposed. Be careful not to touch any inner components when  
changing the battery.  
6. Remove the two (2) main connecting wires (the Red and Black ones) from the  
batteries.  
7. You can now easily remove the batteries from the unit  
Caution: Do not dispose of the batteries in a fire.  
Caution: Do not attempt to open the batteries.  
Caution: The following precautions should be taken when replacing the batteries  
a) Remove watches, rings, etc.  
b) Use tools with insulated handles  
8. Place your new batteries in the same position, direction and reconnect the wires. The  
red wire to the positive (+) pole and black wire to the negative (-) pole.  
9. Please reverse steps 5, 4 and 3 (in that order) to reassemble the unit.  
10. Follow the start-up instructions to properly reconnect your equipment.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Troubleshooting  
Please follow the guidelines below for solutions to common problems:  
Check UPS input plug and wiring.  
Check UPS input voltage.  
Please prepare the information as follows for service personnel:  
UPS model number and serial number  
Description of problem(s) in detail.  
General Problems  
Problems  
Possible causes  
Solution  
Fuse/Breaker at back panel open Replace Fuse/Switch breaker on  
UPS has no reaction  
while AC power is  
connected  
No AC input  
UPS fault  
Check AC power  
Call for service  
Battery failure  
Call service center to replace batteries  
UPS no reaction while  
AC power is connected,  
yet starts after pushing  
power on/off switch  
Breaker at back panel blown  
No AC input  
UPS AC detecting circuit fail  
Switch breaker  
Check AC power  
Call for service  
UPS goes into back-up Utility voltage or frequency  
mode while connected to abnormal  
Check AC power  
Call for service  
AC power  
UPS AC detecting circuit failure  
Inverter fault.  
Over temperature  
Battery over voltage.  
DC bus fault.  
Call for service  
Check load situation  
Fault LED lit  
Overload fault.  
Battery can not provide Battery deteriorated  
normal back-up power in Batteries not fully charged  
the event of a blackout Battery charger damaged  
After AC connected to  
Charge batteries and reset  
If that doesn’t work call for service  
UPS, alarm sounds short  
Abnormal utility power  
and fast beeps and UPS  
Check input power  
shuts down  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Storage  
Storage Conditions  
Store the UPS covered and upright in a cool, dry location, with its battery fully charged.  
Before storing, charge the UPS for at least eight (8) hours. Remove any accessories from  
the accessory slot and disconnect any cables connected to the computer interface port to  
avoid unnecessary drain on the battery.  
Extended Storage  
During extended storage periods in environments where the ambient temperature is -15 to  
+30°C (+5 to +86°F), charge the UPS‘s battery every 6 months.  
During extended storage in environments where the ambient temperature is +30 to +45°C  
(+86 to +113°F), charge the UPS‘s battery every 3 months.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Battery Bank Installation  
Install up to 8 battery banks per L Series UPS following the instructions below.  
1
2
3
4
BLACK  
RED  
Caution: Make sure the UPS is shutdown and unplugged before connecting additional  
Battery Packs (refer to Switching the UPS “Off” section, page 11)  
1. Locate the external battery connector located at the rear of the UPS.  
2. Make sure you are connecting the connector correctly or problems will occur.  
3. Insert the battery bank connector into the UPS.  
4. The UPS is now ready to be turned on with extended runtime.  
To install additional battery banks, repeat this procedure using the battery bank connectors on  
the back of the battery banks.  
Note: Do not stack battery banks, and make sure proper polarity.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
Specifications  
Specification  
MODEL NO.  
GES-801L  
GES-102L  
GES-152L  
GES-202L  
GES-302L  
Comparison  
MAXIMUM CAPACITY  
UPC ORDER CODE  
NOMINAL VOLTAGE  
VOLTAGE RANGE  
FREQUENCY RANGE  
NOMINAL VOLTAGE  
AUTO VOLTAGE REGULATION  
CURRENT  
800VA / 560W  
1kVA / 700W  
1.5kVA / 1050W 2kVA / 1400W  
3kVA / 2100W  
GENERAL  
825433 22100  
825433 22200  
825433 22300  
120VAC (220 optional)  
+ / - 25%  
825433 22400  
825433 22500  
INPUT  
50 or 60 Hz auto-sensing + / - 5%  
120VAC  
+15% for 90 - 109VAC; -15% for 130 - 150VAC  
6.6A  
8.33A  
12.5A  
16.6A  
25A  
FREQUENCY  
50Hz / 60Hz (Auto Detected) + / - 0.5%  
0.5 - 1.0  
OUTPUT  
POWER FACTOR  
WAVE FORM (ON BATTERY)  
LOAD CREST FACTOR  
TRANSFER TIME  
OUTLETS  
TRUE SINE WAVE  
3:1 (ON BATTERY)  
2 - 4ms (Typical), including detection time  
4
4
6
6
4 + Hardwired  
BATTERY TYPE  
SEALED LEAD ACID - MAINTENANCE FREE  
QUANTITY  
2
2
3
4
4x2  
BATTERY  
VOLTAGE  
24VDC  
24VDC  
36VDC  
48VDC  
48VDC  
RECHARGE TIME  
FULL LOAD  
2 to 4 Hours; Recovery = 90%, Typically  
8 MIN.  
20 MIN.  
41 MIN.  
7 MIN.  
17 MIN.  
41 MIN.  
7 MIN.  
25 MIN.  
70 MIN.  
Available  
7 MIN.  
25 MIN.  
75 MIN.  
8 MIN.  
25 MIN.  
90 MIN.  
HALF LOAD  
BACKUP POWER TIME  
EXTENDED RUN TIME  
PENTIUM & 17" MON  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
OUTPUT SHORT  
YES  
ABNORMAL VOLTAGE  
YES  
MODEM OR NETWORK  
SINGLE LINE (2 wire RJ11) / NETWORK (UTP, RJ45) COMPATIBLE JACKS  
COMMON & NORMAL MODE NOISE SUPPRESSION  
PROTECTION  
I/O NOISE PROTECTION  
I/O SPIKE & TRANSIENT  
PROTECTION  
YES  
COMMUNICATION  
RS 232 / DRY CONTACT (OPTIONAL SNMP OR AS400)  
NORMAL / BACKUP / LOW BATTERY / FAULT / CHECK BATTERY / BUCK / BOOST  
ON BATTERY, LOW BATTERY, OVERLOAD, FAULT  
0 - 40°C (32 - 104°F)  
INTERFACE  
ENVIRONMENT  
LED DISPLAY  
AUDIBLE ALARMS  
OPERATING TEMPERATURE  
HUMIDITY  
0 - 95% (NON-CONDENSING)  
AUDIBLE NOISE  
SAFETY  
< 40 dBA AT 1 METER FROM UNIT  
cUL, UL1778, CSA C22.2  
SAFETY APPROVAL  
EMI / RFI  
FCC CLASS B  
SURGE / TRANSIENT  
UPS WxDxH mm (in.)  
IEEE C62.41 CAT.A  
140x436x210 (5.5x17.2x8.3)  
170x450x226 (6.7x17.7x8.9)  
170x450x226  
(6.7x17.7x8.9)  
EXTERNAL BATTERY BANK (if  
applicable)  
INTERNAL BATTERIES  
PHYSICAL DATA  
46 (101.4)  
WEIGHT in kg (lbs)  
14.5 (32)  
15 (33)  
25 (55.1)  
30 (66.1)  
(including battery bank)  
MODEL NO.  
GES-801LR  
GES-102LR  
GES-152LR  
GES-202LR  
825433 22401  
483x381x133  
GES-302LR  
825433 22501  
483x381x178  
UPC Order Code  
825433 22105  
825433 22201  
825433 22301  
RACK-MOUNT MODELS  
WxDxH mm (in.)  
483x381x89 (19x15x3.5) [2U]  
20 (44) 26.1 (57.5)  
(19x15x5.25) [3U] (19x15x7) [4U]  
WEIGHT in kg (lbs)  
18 (35.3)  
28.4 (62.6) 46.4 (102.3)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always “On” UPS Systems Inc.  
CONTACT INFORMATION  
Additional Purchases or Upgrades  
Always “On” UPS Systems Inc.  
Bldg 1 – 150 Campion Road,  
Kelowna, BC, Canada, V1X 7S8  
Phone: (250) 491-9777 Ext 451  
Fax:  
(250) 491-9775  
QA / Warranty Questions  
Always “On” UPS Systems Inc.  
Bldg 1 – 150 Campion Road,  
Kelowna, BC, Canada, V1X 7S8  
Phone: (250) 491-9777 Ext 209  
Fax:  
(250) 491-9775  
Software Questions  
Always “On” UPS Systems Inc.  
Bldg 1 – 150 Campion Road,  
Kelowna, BC, Canada, V1X 7S8  
Phone: (250) 491-9777 Ext 204  
Fax:  
(250) 491-9775  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  

La Crosse Technology Clock WT 8029U User Manual
Lindy Chipper 42856 User Manual
LSI Network Card U80ALVD User Manual
Magnavox CRT Television 20MT4405 User Manual
Marantz Stereo System MA 9S1 User Manual
Masterbuilt Charcoal Grill 10040607 14 User Manual
MaxTech Computer Monitor XT4871 User Manual
METRObility Optical Systems Power Supply ACPS 17HS User Manual
Micronics Car Seat W6 LI User Manual
Microsoft Cell Phone Smartphone 2002 User Manual