www.mgeups.com
MGE UPS SYSTEMS
Pulsar Evolution
1500 /1500 Rack
1100 /1100 Rack
800 /800 Rack
500 Rack
Installation and user
manual
English
Français
Deutsch
Italiano
Español
Nederlands
W
O
O
O
S
L
I
I
T
O
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 2 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment.
The Pulsar Evolution range has been designed with the utmost care. We recommend that you take the time to read this
manual to take full advantage of the many features of your UPS.
MGE UPS SYSTEMS pays great attention to the environmental impact of its products. Measures that have made Pulsar
Evolution a reference in environmental protection include:
◗ the eco-design approach used in product development,
◗ recycling of Pulsar Evolution at the end of its service life.
To discover the entire range of MGE UPS SYSTEMS products and the options available for the Pulsar Evolution range,
we invite you to visit our web site at www.mgeups.com or contact your MGE UPS SYSTEMS representative.
Important: before installing and using the UPS, always read the safety instructions (document n° 3400722200).
34007117EN/AB - Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Foreword
Using this document
Information may be found in two ways, using:
◗ the contents;
◗ the index.
Pictograms
Important instructions that must always be followed.
Information, advice, help.
Visual indication.
Action.
Audio indication.
In the illustrations on the following pages, the symbols below are used:
LED off.
LED on.
LED flashing.
Page 4 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1. Presentation
1.1 Overall view ................................................................................................................................. 7
Tower models .................................................................................................................................. 7
Rack models ................................................................................................................................... 7
1.2 Back ............................................................................................................................................. 8
1.3 Control panel ................................................................................................................................. 9
2. Installation
2.1 Unpacking and parts check ....................................................................................................... 10
Tower models ................................................................................................................................ 10
Rack models ................................................................................................................................. 11
2.2 Installation ................................................................................................................................... 12
Tower models ................................................................................................................................ 12
800/1100/1500 Rack models ........................................................................................................ 13
500 Rack model ............................................................................................................................ 14
2.3 Connecting the protected equipment ....................................................................................... 15
2.4 Connection to the RS232 or USB communications port (optional)......................................... 16
2.5 Connection to the data-line protection port (optional) ............................................................. 16
2.6 Installation of the communications-card option ...................................................................... 17
3. Operation
3.1 Start-up ........................................................................................................................................ 18
3.2 Shift to booster or fader mode (during voltage variations in the AC-input power)..................... 18
3.3 Operation on battery power (following failure of AC-input power) ............................................. 19
Transfer to battery power .............................................................................................................. 19
Threshold for the low-battery warning........................................................................................... 19
3.4 Personalisation (optional) ........................................................................................................... 20
Function ........................................................................................................................................ 20
ON / OFF conditions tab ............................................................................................................... 20
Battery tab..................................................................................................................................... 20
Voltage-thresholds tab .................................................................................................................. 21
Sensitivity tab ................................................................................................................................ 21
34007117EN/AB - Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
4. Maintenance
4.1 Trouble-shooting......................................................................................................................... 22
4.2 Replacement of the battery module .......................................................................................... 23
Tower models ................................................................................................................................ 23
Rack models ................................................................................................................................. 25
5. Environment ..................................................................................................................................... 27
6. Appendices
6.1 Technical data ............................................................................................................................. 28
Simplified diagram ........................................................................................................................ 26
Technical characteristics ............................................................................................................... 29
Examples of battery backup times ................................................................................................ 30
6.2 Glossary....................................................................................................................................... 31
6.3 Index............................................................................................................................................. 32
Page 6 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentation
1.1 Overall view
Tower models
Dimensions in mm
(W x H x D)
D
Evolution 800
Evolution 1100
Evolution 1500
150 x 237 x 415
150 x 237 x 415
150 x 237 x 483
Weight in kg
H
Evolution 800
Evolution 1100
Evolution 1500
10.5
11.5
15
P
U
L
S
A
R
Evolution
1
1
0
0
W
Rack models
Dimensions in mm
(W x H x D)
D
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
438 x 43.5 x 353
438 x 43.5 x 499
438 x 43.5 x 499
H
438 x 43.5 x 522
(19") (1U)
P
U
L
S
A
R
Weight in kg
Evolution
W
1500 Rack
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
9
15.5
16
19
34007117EN/AB - Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentation
1.2 Back
Pulsar Evolution 800 / 1100 / 1500
Pulsar Evolution 1500:
7
USB communications port.
RS232 communications port.
Data-line protection.
1
2
3
4
8
5
4
5
Slot for communications-card option.
2
1
2
Outlets for direct connection of
protected equipment.
6
1
6
7
Programmable outlets (1 and 2).
Input circuit-breaker.
3
8
Socket for connection to AC-power
source.
Pulsar Evolution 500 / 800 / 1100 Rack
1
2
8
7
5
6
3
2
1
4
Pulsar Evolution 1500 Rack
1
2
4
8
7
2
1
3
5
6
Page 8 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentation
1.3 Control panel
10
Iluminated ON/OFF button for the outlets.
11
12
Operation on battery power.
UPS fault.
Battery fault.
13 Overload.
Group 1 programmable outlets supplied with power.
14
1
2
15 Group 2 programmable outlets supplied with power.
16 Booster or fader mode.
17
Bargraph indicating percent load at output.
%
%
18
Bargraph indicating the battery charge level.
76 to 100%.
51 to 75%.
26 to 50%.
0 to 25%.
34007117EN/AB - Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
2.1 Unpacking and parts check
Tower models
20
21
22
23
24
P
U
L
S
A
R
Evolution
1
1
0
0
20 Two cords for connection of the protected equipment.
21 RS232 communications cable.
22
23
USB communications cable.
CD-ROM with the Solution-Pac and UPS Driver software.
24 Product documentation.
Page 10 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
Rack models
20
21
22
23
25
24
26
P
U
L
S
A
R
Evolution
1500 Rack
20
21
22
23
24
Two cords for connection of the protected equipment.
RS232 communications cable.
USB communications cable.
CD-ROM with the Solution-Pac and UPS Driver software.
Product documentation.
25 Telescopic rails for mounting in 19" bay with mounting hardware.
26
Securing system for equipment power cords.
34007117EN/AB - Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
2.2 Installation
Tower models
P
U
L
S
A
R
Evolution
1
1
0
0
P
U
L
S
A
R
Evolution
1
1
0
0
Page 12 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
800/1100/1500 Rack models
Follow steps 1 to 6 for rack mounting of the UPS on the rails.
2
1
6
2
2
4
3
5
2
P
U
L
S
A
R
Evolution
1500 Rack
6
5
3
The rails and the necessary mounting hardware are supplied by MGE UPS SYSTEMS.
34007117EN/AB - Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
500 Rack model
2
1
P
U
L
S
A
R
Evolution
1500 Rack
3
1
3
P
U
L
S
A
R
Evolution
1500 Rack
P
U
L
S
A
R
Evolution
1500 Rack
Page 14 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
2.3 Connecting the protected equipment
A Pulsar Evolution 1500 tower UPS has been used below to illustrate the instructions. The principle is the same for all the
other tower and rack models.
Check that the indications on the rating plate on the back of the UPS correspond to your AC-power system and to
the actual electrical consumption of all the equipment to be connected to the UPS.
1 - Remove the power cord supplying the
equipment to be protected.
8
2 - Connect the power cord (1) just removed
from the equipment to the AC-power socket
8 , and then to the AC-power wall outlet.
3 - Connect the protected equipment to the
UPS using the two cords 20 .
Connect priority loads to the two standard
outlets
5
and any non-priority loads to the
(1 and 2).
two programmable outlets
6
If the UPS is connected to a
computer running MGE
2
1
communications software, it is
possible to program the
interruption of power to the
programmable outlets
6
during
operation on battery power, thus
reserving backup power for the
priority loads.
6
5
4 - Lock the connections using the securing
system 26 (for rack models only).
20
As soon as the UPS is energised, the battery begins charging. Eight hours are required to charge to the full rated
backup time.
(1) Make sure the cord has the following
characteristics: 250 V, 10 A, cross-sectional area
1 mm2, type HO5.
34007117EN/AB - Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
A Pulsar Evolution 1500 tower UPS has been used below to illustrate the instructions. The principle is the same for all the
other tower and rack models.
2.4 Connection to the RS232 or USB communications port (optional)
The RS232 and USB
21
communications ports cannot
operate simultaneously.
1 - Connect the RS232 21 or USB 22
communications cable to the serial port or
the USB port on the computer.
RS232
2
1
22
2 - Connect the other end of the
communications cable 21 or 22 to the
RS232
2
or USB
1
communications
port on the UPS.
The UPS can now communicate with all
MGE UPS SYSTEMS supervision, set-up or
safety software.
2.5 Connection to the data-line protection port (optional)
The data-line protection function on the UPS
eliminates overvoltages flowing on the
computer-network lines.
Simply connect the line to be protected to
the UPS using the data-line protection
connectors (IN and OUT) as indicated
opposite (RJ45 cables not supplied).
RS232
IN
OUT
DATA LINE
PROTECTION
Page 16 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
2.6 Installation of the communications-card option
1 - Remove the slot cover
two screws.
4
secured by
4
Restricted-access slot for
the communications card
2 - Insert the card in the slot.
3 - Secure the cover with the two screws.
RS232
DATA LINE PROTECTION
IN
OUT
It is not necessary to shut down the UPS to install the communications card.
This operation must be carried out by qualified personnel.
34007117EN/AB - Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Operation
3.1 Start-up
Press the ON / OFF button 10 .
The buzzer beeps and all the LEDs come ON.
The buzzer beeps twice during the self-test, then button 10 remains
ON, indicating that the outlets are supplied with power.
- AC power is present: Only button 10 is ON. The protected
equipment is supplied by the AC-power source.
- AC power is absent: Button 10 and LED 11 are ON. The protected
equipment is supplied by the UPS, operating on battery power.
10
11
12
1
2
%
%
All the connected equipment is supplied with power.
If button 10 or LED 11 are not ON or if LED 12 is ON, there is a fault (see section 4.1).
Note: The battery is charged as soon as the UPS is connected to the AC-power source, even if button 10 is in the OFF
position.
3.2 Shift to booster or fader mode
(during voltage variations in the AC-input power)
The booster and fader functions maintain the output voltage supplied by
the UPS within close tolerances around the rated value even if
significant voltage variations occur in the AC-input power. This avoids
calling on battery power.
The values defining the voltage range may be set using the UPS Driver
software.
During operation in booster or fader mode, LED 16 is ON, signalling a
significant voltage variation in the AC-input power.
1
2
16
%
%
Page 18 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Operation
3.3 Operation on battery power (following failure of AC-input power)
Transfer to battery power
The AC-input power is out of tolerances, LED 11 goes ON.
During operation on battery power, the buzzer beeps every ten seconds.
The equipment connected to the UPS is supplied by the battery.
11
1
2
%
%
Threshold for the low-battery warning
When the threshold is reached, the buzzer beeps every three seconds.
The low-battery warning threshold can be set by the user, with the “UPS
Driver” software.
There is very little remaining battery backup time. Close all
applications because UPS automatic shutdown is imminent.
11
1
2
When the battery reaches the end of its backup time, the UPS shuts
down and all the LEDs go OFF.
%
%
The equipment is no longer supplied with power.
The UPS automatically restarts when power returns.
If the UPS does not restart, check that the “automatic restart when power returns” function has not been disabled (see
section 3.4 Personalisation).
34007117EN/AB - Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Operation
3.4 Personalisation (optional)
Function
Personalisation parameters can be set and modified using the UPS Driver software installed on a computer that is
connected to the UPS (see section 2.4 Connection to the RS232 communications port).
Check that the RS232 21 communications cable is connected.
UPS Driver installation:
1 - Insert the Solution-Pac CD-ROM containing the UPS Driver software in the drive of a PC running Windows.
2 - Open the Windows File manager or Explorer and select the CD-ROM drive.
3 - Double-click "\Emb\Evolutio\Config\upsdriv.exe".
Once UPS Driver has been installed, UPS parameters can be modified in a window containing a number of tabs, each
presenting a set of parameters :
ON / OFF conditions tab
Configurable function
Default setting
Enabled
Options
Disabled
Disabled
Disabled
Enabled
Disabled
Automatic restart
Cold start
Enabled
Forced reboot
Enabled
Energy saving
Disabled
Enabled
UPS ON / OFF via software
Battery tab
Configurable function
Interval between automatic battery tests
Low-battery warning threshold
Default setting
Options
Every day
Once a month
No test
Once a week
20% of the remaining battery
backup time
10 to 40% of the remaining battery
backup time
Protection against deep discharges
Enabled
Disabled
Page 20 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Operation
Voltage-thresholds tab
Configurable function
Default setting
230 V
Options
200 V - 220 V - 240 V
271 to 294 V
Output voltage on battery power
Upper threshold for transfer to battery power
Fader-mode cut-in threshold
294 V
265 V
244 to 265 V
Booster-mode cut-in threshold
184 V
184 to 207 V
Lower threshold for transfer to battery power
Maximum input-voltage range
160 V
160 to 180 V
Disabled
Enabled (1)
(1) Lower threshold for transfer to battery power = 150 V
Sensitivity tab
Configurable function
Default setting
Options
UPS sensitivity level
Normal
High or low
For more informations about these settings, refer to the Help function of the "UPS Driver" software.
34007117EN/AB - Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
4.1 Trouble-shooting
Troubleshooting not requiring MGE UPS SYSTEMS after-sales support (all versions)
Indication
Signification
Correction
LED 13 flashes and the UPS overload. The power drawn by the connected
Check the power drawn by the
equipment and disconnect any non-
priority devices.
buzzer beeps once.
LED 12 flashes.
equipment exceeds UPS capacity.
A battery fault was detected during the automatic
battery test.
Replace the battery module (see
section 4.2).
Troubleshooting requiring MGE UPS SYSTEMS after-sales support
Indication
Signification
Correction
LED 12 goes ON and
the buzzer sounds
continuously.
UPS electronics have detected a UPS fault.
◗ The connected equipment is no longer supplied.
Call the after-sales support
department.
The equipment connected to the UPS is no
longer protected.
Page 22 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
4.2 Replacement of the battery module
Safety rules
Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions
must be taken for all handling:
◗ remove all watches, rings, bracelets and any other metal objects;
◗ use tools with insulated handles.
Tower models
Removal of the battery module
This operation may be carried out with the UPS supplying power to the load.
A
- Unclip the small plate with the MGE
logo on the front panel of the UPS.
B
C
- Remove the two screws.
- Remove the left-hand side of the front
panel by pulling it slightly up and then
forward.
C
P
U
L
S
A
R
Evolution
1
5
0
0
B
A
D
- Disconnect the battery module by
pulling apart the connectors (never pull on
the cables).
D
34007117EN/AB - Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
E
- Remove the battery module by pulling
on the plastic tab and proceed with
replacement.
E
Installation of the new battery module
Carry out the above operation in reverse order.
◗ Caution: risk of electric arc when connecting the battery.
◗ To maintain an identical level of performance and safety, use a battery module identical to that previously
mounted in the UPS.
◗ Press the two parts of the battery connector tightly together to ensure proper connection.
Page 24 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
Rack models
Removal of the battery module
This operation may be carried out with the UPS supplying power to the load.
A
- Unclip the small plate with the MGE
logo on the front panel of the UPS.
B
C
- Remove the two screws.
- Remove the left-hand side of the front
panel by pulling it forward.
PULSAR
Evolution
1
5
0
0
C
B
A
D
- Disconnect the battery module by
pulling apart the connectors (never pull on
the cables).
D
34007117EN/AB - Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
E
- Remove the cover.
E
F
- Remove the battery module by pulling
on the plastic tab and proceed with
replacement.
F
Installation of the new battery module
Carry out the above operation in reverse order.
◗ Caution: risk of electric arc when connecting the battery.
◗ To maintain an identical level of performance and safety, use a battery module identical to that previously
mounted in the UPS.
◗ Press the two parts of the battery connector tightly together to ensure proper connection.
Page 26 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Environment
This product has been designed to respect the environment:
It does not contain CFCs or HCFCs.
UPS recycling at the end of service life:
MGE UPS SYSTEMS undertakes to recycle, by certified companies and in compliance with all applicable regulations, all
UPS products recovered at the end of their service life (contact your MGE branch office).
Packing:
UPS packing materials must be recycled in compliance with all applicable regulations.
Warning:
This product contains lead-acid batteries. Lead is a dangerous substance for the environment if it is not properly recycled
by specialised companies.
Web site: www.mgeups.com
34007117EN/AB - Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Appendices
6.1 Technical data
Simplified diagram
Filter
Booster / fader transformer
Input
Output
Inverter
Charger
Battery
Page 28 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Appendices
Technical characteristics
Pulsar Evolution
500
1500 / 1500 rack
800 / 800 rack
1100 / 1100 rack
500 VA / 350 W
1500 VA / 1000 W
Output rating
800 VA / 560 W
1100 VA / 700 W
AC-input power
◗ Voltage
◗ Frequency
Single-phase, 160 V to 294 V (1) , 230V nominal.
47 Hz to 70 Hz (50 Hz system) or 56.5 Hz to 70 Hz (2) (60 Hz system)
Output power (operation
on battery power)
◗ Voltage
Single-phase, 230 V (3) (+ 6% / - 10%)
50/60 Hz +/- 0.1 Hz
◗ Frequency
Battery (sealed lead-acid,
maintenance free)
◗ Tower models
3 x 12 V - 9 Ah,
6 x 6 V - 9 Ah
2 x 12 V - 7.2 Ah,
4 x 6 V - 7.2 Ah
2 x 12 V - 9 Ah,
4 x 6 V - 9 Ah
2 x 6 V - 9 Ah,
◗ Rack models
Environment
<40 dBA
0 to 35° C
20 to 90%
<40 dBA
0 to 40° C
20 to 90%
◗ Noise level (operation on
AC-input power)
◗ Operating temperature
◗ Relative humidity
(without condensation)
(1) The upper and lower thresholds may be set using the UPS Driver software.
(2) Or 40 Hz in low-sensitivity mode (may be set using the UPS Driver software).
(3) Adjustable from 200 to 240 V using the UPS Driver software.
34007117EN/AB - Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Appendices
Examples of battery backup times
Pulsar Evolution 500
2 rack-optimized dense servers
1 router
1 hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 800
3 rack-optimized dense servers
2 file/print servers
1 data server + 1 hub + 1 router
1 router
1 hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1100
3 rack-optimized dense servers
2 file/print servers
1 data server + 1 hub + 1 router
1 router
1 hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1500
5 rack-optimized dense servers
3 file/print servers
2 data servers + 1 hub + 1 router
1 router
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Page 30 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Appendices
6.2 Glossary
Backup time
Time that the connected equipment can operate on battery power if AC-input power fails.
Bargraph
Device on the front panel indicating the percent remaining backup time or the percent
load.
Booster mode
Automatic UPS operating mode whereby the input-power voltage is increased if it drops
below a value set in the personalisation parameters, thus avoiding a battery discharge.
De-energised
Equipment
The UPS must be physically disconnected from the AC-input power.
Devices and systems connected to the UPS output.
Fader mode
Automatic UPS operating mode whereby the input-power voltage is decreased if it rises
above a value set in the personalisation parameters, thus avoiding a battery discharge.
Input circuit breaker
Outlets
Circuit breaker protecting the upstream distribution system against UPS faults.
Pulsar Evolution has a group of four non-programmable outlets.
Personalisation
The parameters for a number of UPS functions may be modified using the UPS Driver
software to adapt UPS operation to user needs.
Programmable outlets
Pulsar Evolution has two groups of two programmable outlets. They may be used for
sequential start-up of protected equipment, shedding of non-priority loads during
operation on battery power or management of operating priorities to provide the most
critical devices with more backup time before battery power runs out. These outlets may
be programmed using the Solution-Pac software on the CD-ROM supplied with the
UPS.
RS232 communications port
Solution-Pac
For UPS connection to a computer via the serial port.
MGE UPS SYSTEMS safety, set-up and supervision software suite on the CD-ROM
supplied with the UPS.
UPS
Uninterruptible Power Supply.
UPS Driver
Communications software on the CD-ROM supplied with the UPS. It may be used to
personalise the default settings.
USB communications port
For UPS connection to a computer via the USB port.
34007117EN/AB - Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Appendices
6.3 Index
A
M
Mode
Automatic start ............................................................... 20
Booster mode ..................................................... 9, 18
B
Fader mode ........................................................ 9, 18
Sleep mode (automatic start) ................................. 20
Bargraph .......................................................................... 9
Battery
Backup time............................................................ 30
End of backup time................................................. 19
Fault ......................................................................... 9
Personalisation ....................................................... 20
Recycling ................................................................ 27
Replacement .............................................. 22, 23, 24
Threshold for low-battery warning .......................... 19
Transfer to battery power ................................... 9, 19
Buttons ............................................................................. 9
Buzzer ............................................................................ 19
O
Overloads ................................................................... 9, 22
P
Personnalisation ........................................................... 20
Battery ....................................................................20
ON / OFF conditions.............................................. 20
Output.................................................................... 21
Ports
RS232 ................................................................8, 16
USB ....................................................................8, 16
Programmable outlets ..................................................8, 9
C
Circuit breakers
Battery circuit breaker .............................................. 8
Input circuit breaker .................................................. 8
Communication
S
Safety .............................................................................23
Start-up ..........................................................................18
Cards .................................................................. 8, 17
Ports ................................................................... 8, 16
Connections
T
Technical characteristics ................................................29
Data-line protection ................................................ 16
RS232 communications port .................................. 16
USB communications port ...................................... 16
Temperature (excessive ambient) ..................................29
U
UPS Driver .................................................. 18, 19, 20, 29
UPS ON / OFF via software ...........................................20
D
Dimensions ...................................................................... 7
W
E
Web site ........................................................................ 27
Environment ................................................................... 27
Weight ..............................................................................7
F
Fault (UPS) ...................................................................... 9
L
LEDs ................................................................................ 9
Page 32 - 34007117EN/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
www.mgeups.com
MGE UPS SYSTEMS
Pulsar Evolution
1500 /1500 Rack
1100 /1100 Rack
800 /800 Rack
500 Rack
Manuel d'installation
et d'utilisation
R
E
T
Ê
R
R
A
S
U
O
V
T
I
O
D
E
N
N
E
R
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 2 - 34007117FR/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Nous vous remercions d'avoir choisi un produit MGE UPS SYSTEMS pour assurer la sécurité des équipements qu'il
alimente.
La gamme Pulsar Evolution a été élaborée avec le plus grand soin.
Pour exploiter au mieux les performances de l'ASI (Alimentation Sans Interruption), nous vous conseillons de prendre le
temps de lire ce manuel.
MGE UPS SYSTEMS se préoccupe de l'impact de ses produits sur l'environnement.
Les ressources mises en oeuvre font de Pulsar Evolution une référence en matière de protection de l'environnement dont
en particulier :
◗ une démarche d'éco-conception pendant son cycle de développement,
◗ le recyclage de Pulsar Evolution en fin de vie du produit.
Nous vous invitons à découvrir l'offre de MGE UPS SYSTEMS ainsi que les options de la gamme Pulsar Evolution en
visitant notre site WEB à www.mgeups.com ou en contactant votre représentant MGE UPS SYSTEMS.
Important : avant l’installation et l’utilisation de l’ASI, il est impératif de lire attentivement les consignes de sécurité
(document n° 3400722200).
34007117FR/AB - Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Avant propos
Structure de la documentation
La recherche d’information s’effectue de deux façons :
◗ par le sommaire,
◗ par l’index.
Conventions des pictogrammes
Suivre impérativement ces consignes.
Informations, conseils, aide.
Signalisation visuelle.
Action.
Signalisation sonore.
Les conventions adoptées pour représenter les voyants dans les illustrations sont les suivantes :
Voyant éteint.
Voyant allumé.
Voyant clignotant.
Page 4 - 34007117FR/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Sommaire
1. Présentation
1.1 Vues générales ............................................................................................................................ 7
Modèles "tour"................................................................................................................................. 7
Modèles "rack" ................................................................................................................................ 7
1.2 Faces arrières.............................................................................................................................. 8
1.3 Panneau de contrôle..................................................................................................................... 9
2. Installation
2.1 Déballage et vérification............................................................................................................. 10
Modèles "tour"............................................................................................................................... 10
Modèles "rack" .............................................................................................................................. 11
2.2 Mise en place............................................................................................................................... 12
Modèles "tour"............................................................................................................................... 12
Modèles "rack" 800/1100/1500 ..................................................................................................... 13
Modèle "rack" 500 ......................................................................................................................... 14
2.3 Raccordement des équipements............................................................................................... 15
2.4 Raccordement du port de communication RS232 ou USB (facultatif) .................................... 16
2.5 Raccordement de la protection ligne de données (facultatif) .................................................. 16
2.6 Mise en place de l’option "carte de communication".............................................................. 17
3. Utilisation
3.1 Mise en marche ........................................................................................................................... 18
3.2 Passage en mode "booster" ou "fader" (en cas de variation de tension du réseau électrique)18
3.3 Alimentation sur batterie (en cas d'absence du réseau électrique)........................................... 19
Passage sur batterie ..................................................................................................................... 19
Seuil d’alarme de fin d’autonomie batterie atteint ......................................................................... 19
3.4 Personnalisation (facultatif) ........................................................................................................ 20
Fonction ........................................................................................................................................ 20
Onglet "Conditions On/Off" ........................................................................................................... 20
Onglet "Batterie" ........................................................................................................................... 20
Onglet "Seuils de tension" ............................................................................................................ 21
Onglet "Sensibilité" ....................................................................................................................... 21
34007117FR/AB - Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Sommaire
4. Maintenance
4.1 Dépannage................................................................................................................................... 22
4.2 Remplacement du module batterie ........................................................................................... 23
Modèles "tour"............................................................................................................................... 23
Modèles "rack" .............................................................................................................................. 25
5. Environnement ................................................................................................................................ 27
6. Annexes
6.1 Caractéristiques techniques ...................................................................................................... 28
Schéma synoptique ...................................................................................................................... 26
Caractéristiques techniques.......................................................................................................... 29
Exemples d'autonomies batterie ................................................................................................... 30
6.2 Glossaire...................................................................................................................................... 31
6.3 Index............................................................................................................................................. 32
Page 6 - 34007117FR/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Présentation
1.1 Vues générales
Modèles "tour"
Dimensions en mm
(L x H x P)
P
Evolution 800
Evolution 1100
Evolution 1500
150 x 237 x 415
150 x 237 x 415
150 x 237 x 483
Poids en kg
H
Evolution 800
Evolution 1100
Evolution 1500
10,5
11,5
15
P
U
L
S
A
R
Evolution
1
1
0
0
L
Modèles "rack"
Dimensions en mm
(L x H x P)
P
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
438 x 43,5 x 353
438 x 43,5 x 499
438 x 43,5 x 499
H
438 x 43,5 x 522
(19") (1U)
P
U
L
S
A
R
Poids en kg
Evolution
L
1500 Rack
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
9
15,5
16
19
34007117FR/AB - Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Présentation
1.2 Faces arrières
Pulsar Evolution 800 / 1100 / 1500
Pulsar Evolution 1500 :
7
Port de communication USB.
Port de communication RS232.
Protection des lignes de données.
1
2
3
4
8
5
4
5
Emplacement pour l'option "carte de
communication".
2
1
2
6
1
Prises pour le raccordement des
équipements.
6
7
Prises programmables (1 et 2).
3
Disjoncteur de protection du réseau
électrique d'alimentation.
Pulsar Evolution 500 / 800 / 1100 Rack
8
Prise pour le raccordement au réseau
électrique d'alimentation.
1
2
8
7
5
6
3
2
1
4
Pulsar Evolution 1500 Rack
1
2
4
8
7
2
1
3
5
6
Page 8 - 34007117FR/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Présentation
1.3 Panneau de contrôle
10
Bouton lumineux Marche/Arrêt (ON/OFF) des prises de sortie.
11
12
Fonctionnement sur batterie.
Défaut de l'appareil.
Défaut batterie.
13 ASI en surcharge.
Prises programmables 1 alimentées.
14
1
2
15 Prises programmables 2 alimentées.
16 Fonctionnement en mode "booster" ou "fader".
17
Barregraphe du niveau de puissance utilisée en sortie.
%
%
18
Barregraphe du niveau de charge de la batterie.
De 76 à 100%.
De 51 à 75%.
De 26 à 50%.
De 0 à 25%.
34007117FR/AB - Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
2.1 Déballage et vérification
Modèles "tour"
20
21
22
23
24
P
U
L
S
A
R
Evolution
1
1
0
0
20 2 cordons pour raccorder les équipements.
21 Câble de communication RS 232.
22
23
Câble de communication USB.
CD ROM contenant les logiciels "Solution Pac" et "UPS Driver".
24 Documentation.
Page 10 - 34007117FR/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
Modèles "rack"
20
21
22
23
25
24
26
P
U
L
S
A
R
Evolution
1500 Rack
20
21
22
23
24
2 cordons pour raccorder les équipements.
Câble de communication RS 232.
Câble de communication USB.
CD ROM contenant les logiciels "Solution Pac" et "UPS Driver".
Documentation.
25 Kit de montage en armoire 19".
26
Système de verrouillage des cordons d'alimentation des équipements.
34007117FR/AB - Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
2.2 Mise en place
Modèles "tour"
P
U
L
S
A
R
Evolution
1
1
0
0
P
U
L
S
A
R
Evolution
1
1
0
0
Page 12 - 34007117FR/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
Modèles "rack" 800/1100/1500
Montage et fixation des glissières et du rack : suivre les étapes 1 à 6.
2
1
6
2
2
4
3
5
2
P
U
L
S
A
R
Evolution
1500 Rack
6
5
3
La visserie de fixation et les glissières sont fournies par MGE UPS SYSTEMS.
34007117FR/AB - Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
Modèles "rack" 500
2
1
P
U
L
S
A
R
Evolution
1500 Rack
3
1
3
P
U
L
S
A
R
Evolution
1500 Rack
P
U
L
S
A
R
Evolution
1500 Rack
Page 14 - 34007117FR/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
2.3 Raccordement des équipements
Les consignes ci-dessous sont illustrées par des vues d'un modèle Pulsar Evolution 1500 "tour". Le principe est identique
pour les autres modèles "tour" et "rack".
Vérifier que les indications portées sur la plaque d'identification située à l'arrière de l'appareil correspondent au
réseau électrique d'alimentation et à la consommation électrique réelle des équipements.
1 - Débrancher le cordon d'alimentation de
l'équipement.
8
2 - Connecter ce cordon(1) sur la prise 8 ,
puis sur la prise du réseau électrique
d'alimentation.
3 - Raccorder les équipements à l'ASI à
l'aide des cordons 20 .
Connecter de préférence les équipements
prioritaires sur les 2 prises
5
et les
équipements non prioritaires sur les 2 prises
6
programmables (1 et 2).
Pour pouvoir programmer l'arrêt
2
1
des prises
6
en cours
d'autonomie batterie et optimiser
ainsi la durée de cette autonomie,
il est nécessaire d'avoir accès au
logiciel de communication MGE
UPS SYSTEMS.
6
5
4 - Verrouiller le raccordement en fixant le
système 26 (pour les modèles "rack"
uniquement).
20
Après la première mise sous tension, il faut au moins 8 heures pour que la batterie puisse fournir l'autonomie
nominale.
(1) S'assurer que les caractéristiques de ce cordon
sont : 250V - 10A (section 1mm2, type HO5).
34007117FR/AB - Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
Les consignes ci-dessous sont illustrées par des vues d'un modèle Pulsar Evolution 1500 "tour". Le principe est identique
pour les autres modèles "tour" et "rack".
2.4 Raccordement du port de communication RS232 ou USB (facultatif)
Le port de communication RS232
et le port de communication USB
ne peuvent pas fonctionner
simultanément.
21
1 - Connecter le câble de communication
RS 232 21 ou USB 22 sur le port série
ou USB de l'équipement informatique.
RS232
2
1
22
2 - Connecter l'autre extrémité du câble de
communication 21 ou 22 sur le port
de communication RS232
de l’ASI.
2
ou USB
1
L'ASI peut désormais dialoguer avec un
logiciel d'administration, de personnalisation
ou de sécurité MGE UPS SYSTEMS.
2.5 Raccordement de la protection de la ligne de données (facultatif)
La fonction "protection des lignes de
données" de l'ASI permet d'éliminer les
surtensions véhiculées sur les lignes des
réseaux informatiques.
Pour cela, faire transiter la ligne à protéger
par l'ASI, en utilisant les prises "Data ligne
protection" IN (entrée) et OUT (sortie)
RS232
comme indiqué sur la figure ci-contre
(câbles RJ45 non fournis).
IN
OUT
DATA LINE
PROTECTION
Page 16 - 34007117FR/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation
2.6 Mise en place de l’option "carte de communication"
1 - Oter le plastron
vis.
4
de l'ASI fixé par 2
4
Emplacement, à accès
restreint, de la carte de
communication.
2 - Glisser la carte dans l'emplacement
prévu.
3 - Fixer le plastron de la carte à l'aide des 2
vis.
RS232
DATA LINE PROTECTION
IN
OUT
Il n'est pas nécessaire d'arrêter l'ASI pour installer une carte de communication.
Cette opération doit être effectuée par un personnel qualifié.
34007117FR/AB - Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Utilisation
3.1 Mise en marche
Réseau électrique d'alimentation présent
Réseau électrique d'alimentation absent
L’ensemble des équipements connectés est alors sous tension.
Nota :
3.2 Passage en mode "booster" ou "fader"
(en cas de variation de tension du réseau électrique)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Utilisation
3.3 Alimentation sur batterie (en cas d’absence du réseau électrique)
Passage sur batterie
Les équipements connectés à l’ASI continuent d’être alimentés
grâce à la batterie.
Seuil d’alarme de fin d’autonomie batterie atteint
Il ne reste alors qu’une faible partie d’autonomie batterie, fermez
les applications car l’arrêt automatique de l’ASI est proche.
Les équipements connectés à l’ASI ne sont plus alimentés.
L'ASI redémarre automatiquement dès le retour du réseau électrique.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Utilisation
3.4 Personnalisation (facultatif)
Fonction
Vérifier que le câble RS 232 21 est raccordé.
Onglet "Conditions On/Off"
Fonctions personnalisables
Configuration usine
Personnalisation possible
Onglet "Batterie"
Fonctions personnalisables
Configuration usine
Personnalisation possible
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Utilisation
Onglet "Seuils de tension"
Fonctions personnalisables
Configuration usine
Personnalisation possible
Onglet "Sensibilité"
Fonctions personnalisables
Configuration usine
Personnalisation possible
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
4.1 Dépannage
Dépannage sans intervention du SAV (tous modèles)
Symptôme
Diagnostic
Remède
Dépannage avec intervention du SAV
Symptôme
Diagnostic
Remède
◗
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
4.2 Remplacement du module batterie
Rappel sur les consignes de sécurité :
La batterie présente un risque de choc électrique et un courant de court-circuit élevé.
Les précautions suivantes doivent être prises pour toute intervention sur les éléments batterie :
◗ Oter des mains montres, bagues, alliances, bracelets ou tout autre objet métallique,
◗ Utiliser des outils isolés.
Modèles "tour"
Démontage du module batterie
A
B
C
C
P
U
L
S
A
R
Evolution
1
5
0
0
B
A
D
D
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
E
E
Remontage du nouveau module batterie
◗ Attention : risque d’arc électrique lors du branchement de la batterie.
◗ Pour préserver la sécurité et le même niveau de performance, utiliser des éléments batterie identiques à ceux
montés dans l'ASI.
◗ Veillez à bien enfoncer les parties mâles et femelles du connecteur lors du raccordement.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
Modèles "rack"
Démontage du module batterie
A
B
C
PULSAR
Evolution
1
5
0
0
C
B
A
D
D
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
E
E
F
F
Remontage du nouveau module batterie
◗ Attention : risque d’arc électrique lors du branchement de la batterie.
◗ Pour préserver la sécurité et le même niveau de performance, utiliser des éléments batterie identiques à ceux
montés dans l'ASI.
◗ Veillez à bien enfoncer les parties mâles et femelles du connecteur lors du raccordement.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Environnement
Ce produit est conçu pour respecter l’environnement :
Recyclage de l’ASI en fin de vie :
Emballage :
Avertissement :
Site Web :
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Annexes
6.1 Caractéristiques techniques
Schéma synoptique
Transformateur "booster / fader"
Filtre
Entrée
Sortie
Onduleur
Chargeur
Batteries
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Annexes
Caractéristiques techniques
Pulsar Evolution
1500 / 1500 rack
500
800 / 800 rack
1100 / 1100 rack
Puissance de sortie
Réseau électrique
d'alimentation
◗
◗
Sortie utilisation en
fonctionnement sur
batterie
◗
◗
Batterie plomb étanche
sans entretien
◗
◗
Environnement
◗
◗
◗
°
°
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Annexes
Exemples d'autonomies batterie
Pulsar Evolution 500
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 800
Pulsar Evolution 1100
Pulsar Evolution 1500
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Annexes
6.2 Glossaire
ASI
Autonomie
Barregraphe
Disjoncteur d'entrée
Equipements
Hors tension
Mode "booster"
Mode "fader"
Personnalisation
Port de communication RS232
Port de communication USB
Prises de sortie
Pulsar Evolution
Pulsar Evolution
Prises programmables
Solution-Pac
UPS Driver
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Annexes
6.3 Index
A
P
B
R
S
C
D
T
U
V
E
M
Download from Www.Somanuals.com. All Manuals Search And Download.
www.mgeups.com
MGE UPS SYSTEMS
Pulsar Evolution
1500 /1500 Rack
1100 /1100 Rack
800 /800 Rack
500 Rack
Installations- und
Bedienungsanleitung
W
O
O
O
S
L
I
I
T
O
Download from Www.Somanuals.com. All Manuals Search And Download.
Seite 2 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Einleitung
Wir danken Ihnen, daß Sie sich für ein Produkt von MGE UPS SYSTEMS zur sicheren Stromversorgung Ihrer Systeme
entschieden haben.
Die Baureihe Pulsar Evolution wurde mit größter Sorgfalt entwickelt.
Um die Leistungen Ihrer USV (Unterbrechungsfreien Stromversorgung) optimal nutzen zu können, empfehlen wir Ihnen,
sich ein wenig Zeit zu nehmen und die vorliegende Anleitung aufmerksam zu lesen.
Für MGE UPS SYSTEMS ist Umweltschutz ein wichtiger Aspekt bei der Entwicklung und Herstellung seiner Produkte.
Die ökologische Gesamtkonzeption sowie der konsequente Einsatz der erforderlichen Mittel machen Pulsar Evolution zu
einem beispielhaften Produkt in punkto Umweltfreundlichkeit. Es zeichnet sich besonders aus durch :
◗ den ökologischen Ansatz in allen Phasen der Produktentwicklung,
◗ das Recycling von Pulsar Evolution nach Ablauf der Lebensdauer.
Entdecken Sie das umfassende Angebot von MGE UPS SYSTEMS sowie weitere Optionen zur Baureihe Pulsar
Evolution auf unseren WEB-Sites www.mgeups.com und www.mgeups.de, oder wenden Sie sich persönlich an den
Vertreter von MGE UPS SYSTEMS in Ihrer Nähe.
Achtung: Vor Installation und Inbetriebnahme der USV Sicherheitshinweise lesen! (Anleitung Nr. 3400722200).
34007117DE/AB - Seite 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Vorbemerkungen
Aufbau der Installations- und Bedienungsanleitung
Die Suche nach bestimmten Informationen erfolgt auf einfachste Weise:
◗ über das Inhaltsverzeichnis,
◗ über das Stichwortregister.
Bedeutung der Piktogramme
WICHTIG, Hinweise unbedingt befolgen.
Informationen, Ratschläge, Hilfen.
Optische Anzeige.
Maßnahmen, Handlungen.
Akustischer Alarm.
In den Abbildungen der nachfolgenden Seiten sind die LED-Anzeigen mit folgenden Symbolen dargestellt:
LED AUS.
LED AN.
LED blinkt.
Seite 4 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Inhalt
1. Ansichten und Beschreibung
1.1 Gesamtansicht ............................................................................................................................ 7
Tower- Modell.................................................................................................................................. 7
Rack- Modell ................................................................................................................................... 7
1.2 Rückansicht................................................................................................................................. 8
1.3 Anzeige- und Bedienfeld .............................................................................................................. 9
2. Aufstellung und Installation
2.1 Entfernen der Verpackung und Überprüfung des Lieferumfangs .......................................... 10
Tower- Modell................................................................................................................................ 10
Rack- Modell ................................................................................................................................. 11
2.2 Aufstellung .................................................................................................................................. 12
Tower- Modell................................................................................................................................ 12
Rack- Modell 800/1100/1500 ........................................................................................................ 13
Rack- Modell 500 .......................................................................................................................... 14
2.3 Anschluß der Verbraucher ......................................................................................................... 15
2.4 Anschluß des Kommunikationskabels für RS232- bzw. USB-Schnittstelle (wahlweise) ...... 16
2.5 Anschluß der Verbindung für Datenleitungsschutz (wahlweise) ............................................ 16
2.6 Einbau einer Kommunikationskarte (Option)............................................................................ 17
3. Betriebszustände
3.1 Inbetriebnahme ........................................................................................................................... 18
3.2 Booster- bzw. Fader-Modus (Ausgleich von Netzspannungsschwankungen) ........................... 18
3.3 Batteriebetrieb (bei Netzausfall).................................................................................................. 19
Umschaltung auf Batteriebetrieb................................................................................................... 19
Voralarm "Ende der Autonomiezeit" .............................................................................................. 19
3.4 Kundenspezifische Anpassung per Software (wahlweise) ...................................................... 20
Software, Installation und Funktion ............................................................................................... 20
Registerkarte "Ein/Aus-Bedingungen" .......................................................................................... 20
Registerkarte "Batterie"................................................................................................................. 20
Registerkarte "Spannungsgrenzwerte" ......................................................................................... 21
Registerkarte "Ansprechempfindlichkeit" ...................................................................................... 21
34007117DE/AB - Seite 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Sommaire
4. Wartung und Service
4.1 Fehlerbehebung .......................................................................................................................... 22
4.2 Austausch des Batteriemoduls ................................................................................................. 23
Tower- Modell................................................................................................................................ 23
Rack- Modell ................................................................................................................................. 25
5. Umgebungsbedingungen ........................................................................................................... 27
6. Anhang
6.1 Technische Daten ....................................................................................................................... 28
Blockschaltbild .............................................................................................................................. 26
Kenndaten..................................................................................................................................... 29
Beispiele für Batterie-Autonomiezeiten ......................................................................................... 30
6.2 Fachbegriffe ................................................................................................................................ 31
6.3 Stichwortregister ........................................................................................................................ 32
Seite 6 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Ansichten und Beschreibung
1.1 Gesamtansicht
Tower- Modell
Abmessungen in mm
(B x H x T)
T
Evolution 800
Evolution 1100
Evolution 1500
150 x 237 x 415
150 x 237 x 415
150 x 237 x 483
Gewicht in kg
H
Evolution 800
Evolution 1100
Evolution 1500
10,5
11,5
15
P
U
L
S
A
R
Evolution
1
1
0
0
B
Rack- Modell
Abmessungen in mm
(B x H x T)
T
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
438 x 43,5 x 353
438 x 43,5 x 499
438 x 43,5 x 499
H
438 x 43,5 x 522
(19") (1U)
P
U
L
S
A
R
Gewicht in kg
Evolution
B
1500 Rack
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
9
15,5
16
19
34007117DE/AB - Seite 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Ansichten und Beschreibung
1.2 Rückansicht
Pulsar Evolution 800 / 1100 / 1500
Pulsar Evolution 1500 :
7
USB-Schnittstelle.
RS232-Schnittstelle.
Datenleitungsschutz.
1
2
3
4
8
5
4
5
6
Steckplatz für Kommunikationskarte
(Option).
2
1
2
6
1
2 normale (nicht programmierbare)
Ausgangssteckdosen.
2 programmierbare
3
Ausgangssteckdosen (1 und 2).
7
8
Eingangsschalter.
Netzanschluß.
Pulsar Evolution 500 / 800 / 1100 Rack
1
2
8
7
5
6
3
2
1
4
Pulsar Evolution 1500 Rack
1
2
4
8
7
2
1
3
5
6
Seite 8 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Ansichten und Beschreibung
1.3 Anzeige- und Bedienfeld
10
EIN/AUS-Taster (ON/OFF) mit LED zur Freischaltung/Trennung der
Ausgangssteckdosen.
11
12
Batteriebetrieb.
USV-Störung.
Batteriestörung.
13 Überlast.
Programmierbare Steckdosengruppe 1 an Spannung.
14
1
2
15 Programmierbare Steckdosengruppe 2 an Spannung.
16 Booster- oder Fader-Modus.
17
Balkenanzeige Auslastungsgrad.
%
%
18
Balkenanzeige Batterieladezustand.
76 bis 100%.
51 bis 75%.
26 bis 50%.
0 bis 25%.
34007117DE/AB - Seite 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Aufstellung und Installation
2.1 Entfernen der Verpackung und Überprüfung des Lieferumfangs
Tower- Modell
20
21
22
23
24
P
U
L
S
A
R
Evolution
1
1
0
0
20 2 Verbraucher-Anschlußkabel.
21 RS232-Schnittstellenkabel.
22
23
USB-Schnittstellenkabel.
CD ROM mit USV-Software "Solution Pac" und "UPS Driver".
24 Dokumentation.
Seite 10 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Aufstellung und Installation
Rack- Modell
20
21
22
23
25
24
26
P
U
L
S
A
R
Evolution
1500 Rack
20
21
22
23
24
2 Verbraucher-Anschlußkabel.
RS232-Schnittstellenkabel.
USB-Schnittstellenkabel.
CD ROM mit USV-Software "Solution Pac" und "UPS Driver".
Dokumentation.
25 Montagekit für Einbau in 19"-Schränke.
26
Verriegelungsabdeckung für Verbraucher-Anschlußkabel.
34007117DE/AB - Seite 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Aufstellung und Installation
2.2 Aufstellung
Tower- Modell
P
U
L
S
A
R
Evolution
1
1
0
0
P
U
L
S
A
R
Evolution
1
1
0
0
Seite 12 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Aufstellung und Installation
Rack- Modell 800/1100/1500
Montage und Befestigung der Teleskopschienen für Rackeinbau (Schritte 1 bis 6 befolgen)
2
1
6
2
2
4
3
2
5
P
U
L
S
A
R
Evolution
1500 Rack
6
5
3
Befestigungsschrauben und Teleskopschienen liegen dem Gerät bei.
34007117DE/AB - Seite 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Aufstellung und Installation
Rack- Modell 500
2
1
P
U
L
S
A
R
Evolution
1500 Rack
3
1
3
P
U
L
S
A
R
Evolution
1500 Rack
P
U
L
S
A
R
Evolution
1500 Rack
Seite 14 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Aufstellung und Installation
2.3 Anschluß der Verbraucher
Die nachstehenden Abbildungen zur Illustration der Informationen zeigen das Tower-Modell einer Pulsar Evolution 1500.
Alle Hinweise gelten sinngemäß auch für die übrigen Tower- und Rack-Modelle.
Kenndaten auf dem Typenschild (siehe Geräte-Rückseite) hinsichtlich Übereinstimmung mit den vorhandenen
Netzparametern und der Leistungsaufnahme aller angeschlossenen Verbraucher überprüfen.
1 - Netzkabel der Verbraucher abziehen.
8
2 - Abgezogenes Verbraucher-Netzkabel(1)
in die Gerätesteckdose
8
der USV und
dann in die Netzsteckdose einstecken.
3 - Verbraucher mit Hilfe der Anschlußkabel
20 an die USV anschließen.
Verbraucher höherer Priorität sollten
vorzugsweise an die beiden Steckdosen
und weniger wichtige Verbraucher an die
5
beiden programmierbaren Steckdosen
angeschlossen werden.
6
Um den Abwurf der Steckdosen 6
im Batterietrieb zu programmieren
und so die Nutzung der
2
1
Autonomiereserve zu optimieren,
wird die mitgelieferte USV-
Software benötigt.
6
4 - Verriegelungsabdeckung 26 mit Hilfe
der Befestigungsschrauben anbringen (nur
Rack-Modelle).
5
20
Nach dem erstmaligen Netzanschluß der USV benötigt das Gerät eine Ladezeit von mindestens 8 Stunden, um die
volle Autonomiezeit der Batterie zur Verfügung zu stellen.
(1) Kenndaten des Anschlußkabels überprüfen
(Mindestens 250 V - 10 A, Querschnitt 1 mm2 Typ
HO5).
34007117DE/AB - Seite 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Aufstellung und Installation
Die nachstehenden Abbildungen zur Illustration der Informationen zeigen das Tower-Modell einer Pulsar Evolution 1500.
Alle Hinweise gelten sinngemäß auch für die übrigen Tower- und Rack-Modelle.
2.4 Anschluß des Kommunikationskabels für RS232- bzw. USB-
Schnittstelle (wahlweise)
RS232- und USB-Schnittstelle
21
können nicht gleichzeitig
verwendet werden.
1 - RS232- 21 oder USB-Kabel 22 an die
serielle Schnittstelle bzw. den USB-Port des
zu schützenden Systems anschließen.
RS232
2
1
22
2 - Kabel 21 bzw. 22 mit dem anderen
Ende an die RS232-Schnittstelle
2
oder
den USB-Port der USV anschließen.
1
Die USV kann nun über verschiedene
Softwarepakete von MGE UPS SYSTEMS
mit dem angeschlossenen Rechnersystem
kommunizieren (Überwachung,
Konfiguration, Sicherheitsparameter).
2.5 Anschluß der Verbindung für Datenleitungsschutz (wahlweise)
Mit Hilfe der USV-Funktion
"Datenleitungsschutz" können
Überspannungen in den Datenleitungen des
EDV-Systems verhindert werden.
Hierzu ist die zu schützende Datenleitung
gemäß nebenstehender Abbildung an die
Steckbuchsen "Data line protection" IN/OUT
anzuschließen (RJ45-Kabel (OUT) nicht im
Lieferumfang).
RS232
IN
OUT
DATA LINE
PROTECTION
Seite 16 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Aufstellung und Installation
2.6 Einbau einer Kommunikationskarte (Option)
1 - Abdeckung
4
durch Herausdrehen der
4
zwei Schrauben von der USV lösen.
Steckplatz für
Kommunikationskarte
(beschränkter Zugang).
2 - Karte in den Steckplatz einstecken.
3 - Karte mit den zwei Schrauben
befestigen.
RS232
DATA LINE PROTECTION
IN
OUT
Die Kommunikationskarten können bei eingeschalteter USV installiert werden.
Der Einbau darf nur durch Fachpersonal erfolgen.
34007117DE/AB - Seite 17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Betriebszustände
3.1 Inbetriebnahme
EIN/AUS-Taste 10 drücken.
Der Summer ertönt kurz, und sämtliche LEDs leuchten gleichzeitig auf.
Während des anschließenden Selbstests ertönt der Summer zweimal.
Die LED der Drucktaste 10 leuchtet kontinuierlich und zeigt an, daß die
Ausgangssteckdosen versorgt werden.
10
11
12
- Einspeisenetz vorhanden: Nur die LED der EIN/AUS-Taste 10
leuchtet. Die Verbraucherversorgung erfolgt aus dem Einspeisenetz.
- Einspeisenetz nicht vorhanden: Die LED der EIN/AUS-Taste 10
und die LED 16 leuchten. Die Verbraucherversorgung erfolgt aus der
Batterie über den Wechselrichter der USV.
1
2
%
%
Alle angeschlossenen Verbraucher werden versorgt.
Bleiben die Anzeigen 10 oder 11 erloschen, oder leuchtet LED 12 auf, liegt eine Störung vor (siehe Abschnitt 4.1).
Hinweis: Die Aufladung der Batterie beginnt sofort nach dem Netzanschluß der USV, selbst wenn die EIN/AUS-Taste 10
noch nicht betätigt wurde.
3.2 Booster- bzw. Fader-Modus
(Ausgleich von Netzspannungsschwankungen)
Die Booster- bzw. Fader-Funktion der USV ermöglicht es, die
Ausgangsspannung innerhalb eines definierten Toleranzbereichs zu
halten. Dabei werden größere Netzspannungsschwankungen ohne
Inanspruchnahme der Batterie durch entsprechendes Anheben bzw.
Absenken der Ausgangsspannung ausgeglichen.
Die Grenzwerte dieses Bereichs können über die USV-Software "UPS
Driver" festgelegt werden.
Während des Betriebs der USV im Booster- bzw. Fader-Modus leuchtet
die LED 16 auf und zeigt eine entsprechende
1
2
16
Netzspannungsabweichung an.
%
%
Seite 18 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Betriebszustände
3.3 Batteriebetrieb (bei Netzausfall)
Umschaltung auf Batteriebetrieb
Verläßt das Einspeisenetz den zulässigen Toleranzbereich, schaltet die
USV auf Batteriebetrieb und die LED 11 leuchtet auf.
Während des Batteriebetriebs ertönt alle 10 Sekunden ein akustisches
Signal.
11
Die an die USV angeschlossenen Verbraucher werden
unterbrechungsfrei über die Batterie weiter versorgt.
1
2
%
%
Voralarm "Ende der Autonomiezeit"
Wird dieser Grenzwert erreicht, ertönt der Summer alle 3 Sekunden.
Dieser Alarmgrenzwert kann über die Software "UPS Driver"
kundenspezifisch angepaßt werden.
Die Batterie ist kurz vor dem Entladeende. Es sollten alle
Anwendungen geschlossen werden, da die Abschaltung der USV
kurz bevorsteht.
11
1
2
Erreicht die Batterie das Ende ihrer Autonomiezeit, schaltet die USV ab
und alle LEDs erlöschen.
%
%
Die Verbraucher werden NICHT mehr versorgt.
Bei Rückkehr des Einspeisenetzes schaltet sich die USV automatisch wieder ein.
Ist dies nicht der Fall, ist zu überprüfen, ob die Funktion "Automatischer Neustart" deaktiviert wurde (siehe Abschnitt 3.4
"Kundenspezifische Anpassung per Software").
34007117DE/AB - Seite 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Betriebszustände
3.4 Kundenspezifische Anpassung per Software (wahlweise)
Software, Installation und Funktion
Die kundenspezifische Anpassung der USV kann mit Hilfe der Software "UPS Driver" über einen Rechner erfolgen, der
über die serielle RS232-Schnittstelle mit der USV verbunden ist (siehe Abschnitt 2.4).
Vorhandensein der RS232- 21 Verbindung überprüfen.
Installation der Software "UPS Driver":
1. CD-ROM "Solution Pac" in das Laufwerk des PCs (mit Windows-Betriebssystem) einlegen.
2. Windows-Dateimanager bzw. -Explorer öffnen und CD-ROM-Laufwerk auswählen.
3. Doppelklicken auf die Datei Setup.exe im Verzeichnis "\Emb\Evolutio\Config\".
Nach Installation der Software "UPS Driver" stehen folgende Einstellungsmöglichkeiten zur Verfügung:
Registerkarte "Ein/Aus-Bedingungen"
Einstellungen
Automatischer Neustart
Kaltstart über Batterie
Zwangsabschaltung
Sleep-Modus
Default-Einstellung
Aktiviert
Kundenspezifische Anpassung
Deaktiviert
Aktiviert
Deaktiviert
Aktiviert
Deaktiviert
Deaktiviert
Aktiviert
Aktiviert
USV-Start/Stop über Software
Deaktiviert
Registerkarte "Batterie"
Einstellungen
Default-Einstellung
Kundenspezifische Anpassung
Einmal pro Tag
Einmal pro Monat
Kein Test
Zeitintervall für automatischen Batterietest
Einmal pro Woche
Grenzwert Voralarm "Ende der Autonomiezeit"
Tiefentladungsschutz
20% Restautonomiezeit
Aktiviert
10 bis 40% Restautonomiezeit
Deaktiviert
Seite 20 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Betriebszustände
Registerkarte "Spannungsgrenzwerte"
Einstellungen
Default-Einstellung
Kundenspezifische Anpassung
200 V - 220 V - 240 V
271 bis 294 V
Ausgangsspannung (Batteriebetrieb)
230 V
294 V
Oberer Spannungsgrenzwert für
Umschaltung auf Batterie
Grenzwert für Einschaltung des Fader-Modus’
Grenzwert für Einschaltung des Booster-Modus’
265 V
184 V
160 V
244 bis 265 V
184 bis 207 V
160 bis 180 V
Unterer Spannungsgrenzwert für
Umschaltung auf Batterie
Maximaler Eingangsspannungsbereich
Deaktiviert
Aktiviert(1)
(1) Unterer Spannungsgrenzwert für Umschaltung auf Batterie = 150 V
Registerkarte "Ansprechempfindlichkeit"
Einstellungen
Default-Einstellung
Kundenspezifische Anpassung
Ansprechempfindlichkeit der USV
Normal
Hoch oder niedrig
Nähere Informationen zu den Kennwerten können den Hilfetexten der Software "UPS Driver" entnommen werden.
34007117DE/AB - Seite 21
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Wartung und Service
4.1 Fehlerbehebung
Fehlerbehebung ohne Inanspruchnahme des MGE-Kundendienstes (alle Modelle)
Fehleranzeige
Fehlerursache
Fehlerbehebung
LED 13 blinkt und
Summer ertönt.
Überlastung der USV. Die Leistungsaufnahme der
angeschlossenen Verbraucher übersteigt die
Nennleistung der USV.
Leistungsaufnahme der
angeschlossenen Systeme
überprüfen und weniger wichtige
Verbraucher abschalten.
LED 12 blinkt.
Es wurde beim Batterietest eine Batteriestörung
festgestellt.
Batterien auswechseln (siehe
Abschnitt 4.2).
Fehlerbehebung, die eine Inanspruchnahme des MGE-Kundendienstes erfordert
Fehleranzeige
Fehlerursache
Fehlerbehebung
LED 12 blinkt und
Summer erzeugt
Dauerton.
Es liegt eine interne USV-Störung vor.
◗ Die Versorgung sämtlicher angeschlossenen
Verbraucher ist unterbrochen.
Kundendienst benachrichtigen.
Die an die USV angeschlossenen Systeme
sind nicht mehr geschützt.
Seite 22 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Wartung und Service
4.2 Austausch des Batteriemoduls
Sicherheitsmaßnahmen:
Die Batterie hat einen hohen Kurzschlußstrom und kann Stromschläge verursachen.
Bei jeder Handhabung der Batterien sind daher folgende Sicherheitsmaßnahmen einzuhalten:
◗ Armbanduhren, Ringe, Armreifen und sonstige an Händen oder Armen getragene Metallgegenstände abnehmen.
◗ Werkzeuge mit Isoliergriff verwenden.
Tower- Modell
Ausbau des Batteriemoduls
Die Batterien können bei eingeschalteter USV ausgetauscht werden.
A
- An der Frontseite den Schildträger mit
dem MGE-Logo herausdrücken.
- Die beiden dahinter liegenden
Schrauben lösen.
- Linken Teil der Frontabdeckung leicht
anheben nach vorn abziehen.
B
C
C
P
U
L
S
A
R
Evolution
1
5
0
0
B
A
D
- Batteriemodul durch Lösen der
Steckverbindung (niemals an den
Verbindungskabeln ziehen!) abklemmen.
D
34007117DE/AB - Seite 23
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Wartung und Service
E
- Batteriemodul durch Greifen der
Kunststofflasche herausziehen und durch
neues ersetzen.
E
Einbau des neuen Batteriemoduls
Die oben beschriebenen Handgriffe in umgekehrter Reihenfolge ausführen.
◗ Achtung! Beim Einschieben der neuen Batterie kann es zur Lichtbogenbildung zwischen den Kontakten
kommen.
◗ Zur Gewährleistung der Sicherheit und des Betriebsverhaltens dürfen nur Austauschmodule verwendet werden,
die mit den eingebauten Batterien baugleich sind.
◗ Es ist sicherzustellen, daß der Batteriestecker vollständig in die zugehörige Steckbuchse eingesteckt ist.
Seite 24 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Maintenance
Rack- Modell
Ausbau des Batteriemoduls
Die Batterien können bei eingeschalteter USV ausgetauscht werden.
A
- An der Frontseite den Schildträger mit
dem MGE-Logo herausdrücken.
- Die beiden dahinter liegenden
Schrauben lösen.
- Linken Teil der Frontabdeckung nach
vorn abziehen.
B
C
PULSAR
Evolution
1
5
0
0
C
B
A
D
- Batteriemodul durch Lösen der
Steckverbindung (niemals an den
Verbindungskabeln ziehen!) abklemmen.
D
34007117DE/AB - Seite 25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Wartung und Service
E
- Abdeckung entfernen.
E
F
- Batteriemodul durch Greifen der
Kunststofflasche herausziehen und durch
neues ersetzen.
F
Einbau des neuen Batteriemoduls
Die oben beschriebenen Handgriffe in umgekehrter Reihenfolge ausführen.
◗ Achtung! Beim Einschieben der neuen Batterie kann es zur Lichtbogenbildung zwischen den Kontakten
kommen.
◗ Zur Gewährleistung der Sicherheit und des Betriebsverhaltens dürfen nur Austauschmodule verwendet werden,
die mit den eingebauten Batterien baugleich sind.
◗ Es ist sicherzustellen, daß der Batteriestecker vollständig in die zugehörige Steckbuchse eingesteckt ist.
Seite 26 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Umweltschutz
Bei der Entwicklung des vorliegenden Produkts wurde besonders auf seine Umweltverträglichkeit
geachtet:
Es enthält weder FKW- noch FCKW-Verbindungen.
Recycling der USV nach Ablauf der Lebensdauer:
MGE UPS SYSTEMS verpflichtet sich, sämtliche nach Ablauf der Lebensdauer rückgeführten Komponenten durch
zugelassene Entsorgungsunternehmen einer Wiederverwertung gemäß den gesetzlichen Bestimmungen zuzuführen
(wenden Sie sich bitte an Ihre MGE-Vertretung).
Verpackung:
Verpackungsmaterial muß gemäß den gesetzlichen Bestimmungen entsorgt werden.
Hinweis:
Dieses Produkt enthält Bleibatterien. Blei kann die Umwelt schädigen, wenn es nicht gemäß den gesetzlichen Vorschriften
durch Spezialunternehmen entsorgt wird.
Web-Site: www.mgeups.com
34007117DE/AB - Seite 27
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anhang
6.1 Technische Daten
Blockschaltbild
Filter
Booster-/Fader-Trafo
Netz
Verbraucher
Gleichrichter/
Ladegerät
Wechselrichter
Batterie
Seite 28 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anhang
Kenndaten
Pulsar Evolution
Ausgangsleistung
1500 / 1500 Rack
500
800 / 800 Rack
1100 / 1100 Rack
1500 VA / 1000 W
500 VA / 350 W
800 VA / 560 W
1100 VA / 700 W
Einspeisenetz
◗ Spannung
◗ Frequenz
160 bis 294 V (1), einphasig, Un = 230 V
47 - 70 Hz (50-Hz-Netz) bzw. 56,5 - 70 Hz (2) (60-Hz-Netz)
USV-Ausgang
(Batteriebetrieb)
◗ Spannung
230 V (3) (+6% / - 10%), einphasig
50/60 Hz +/- 0,1 Hz
◗ Frequenz
Batterie (wartungsfreie
Bleiakkus)
◗ Tower- Modell
◗ Rack- Modell
2 x 12 V - 7,2 Ah,
4 x 6 V - 7,2 Ah
2 x 12 V - 9 Ah,
4 x 6 V - 9 Ah
3 x 12 V - 9 Ah,
6 x 6 V - 9 Ah
2 x 6 V - 9 Ah,
Umgebungsbedingungen
◗ Geräuschpegel
<40 dBA
<40 dBA
(Netzbetrieb)
◗ zul. Betriebstemperatur
◗ relative Luftfeuchtigkeit
(ohne Kondensation)
0 bis 35° C
20 bis 90%
0 bis 40° C
20 bis 90%
(1) Oberer und unterer Grenzwert über Software "UPS Driver" einstellbar.
(2) Bis 40 Hz bei niedriger Ansprechempfindlichkeit der USV (einstellbar über USV-Software "UPS Driver").
(3) Einstellbar zwischen 200 und 240 V über USV-Software "UPS Driver".
34007117DE/AB - Seite 29
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anhang
Beispiele für Batterie-Autonomiezeiten
Pulsar Evolution 500
2 optimierte Rack-Server
1 Router
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 800
3 optimierte Rack-Server
2 Print-Server
1 Server + 1 Router + 1 Hub
1 Router
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1100
3 optimierte Rack-Server
2 Print-Server
1 Server + 1 Router + 1 Hub
1 Router
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1500
5 optimierte Rack-Server
3 Print-Server
2 Server + 1 Router + 1 Hub
1 Router
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Seite 30 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anhang
6.2 Fachbegriffe
Ausgangssteckdosen
Pulsar Evolution verfügt abgangsseitig über eine Gruppe von 2 nicht
programmierbaren Ausgangssteckdosen.
Autonomiezeit
Balkenanzeige
Booster-Modus
Betriebsdauer des Geräts mit Verbraucherversorgung über die Batterie bei Ausfall des
Einspeisenetzes.
LED-Leiste am Bedienfeld zur Anzeige des Auslastungsgrads und der
Restautonomiezeit.
Automatische Betriebsart der USV, mit deren Hilfe eine zu geringe Netzspannung ohne
Inanspruchnahme der Batterie um einen einstellbaren Wert angehoben werden kann.
Schalter zum Schutz des Einspeisenetzes gegen Störungen der USV-Anlage.
Eingangsschalter
Fader-Modus
Automatische Betriebsart der USV, mit deren Hilfe eine zu hohe Netzspannung ohne
Inanspruchnahme der Batterie um einen einstellbaren Wert abgesenkt werden kann.
Kundenspezifische
Anpassung
Bestimmte USV-Funktionen können über die Software "UPS Driver" an individuelle
Kundenbedürfnisse angepaßt werden.
Programmierbare
Steckdosen
Pulsar Evolution verfügt abgangsseitig über eine Gruppe von 2 programmierbaren
Ausgangssteckdosen. Sie ermöglichen eine sequentielle Aufschaltung der geschützten
Verbraucher und den Abwurf im Batteriebetrieb, um die Versorgung der kritischsten
Verbraucher am längsten aufrechterhalten zu können. Die Programmierung erfolgt über
die USV-Software "Solution Pac" (mitgelieferte CD-ROM).
RS232-Schnittstelle
Solution-Pac
Serielle Schnittstelle zur Herstellung einer Kommunikationsverbindung zwischen USV
und geschütztem Rechnersystem.
USV-Software zur kundenspezifischen Anpassung von Überwachungs-, Konfigurations-
und Sicherheitsparametern. CD-ROM im Lieferumfang der USV-Anlage.
Spannungsfreischaltung
der USV
Physikalische Trennung der USV vom Einspeisenetz.
UPS Driver
Kommunikationssoftware zur kundenspezifischen Anpassung von USV-Einstellungen.
Auf CD-ROM "Solution-Pac" enthalten.
USB-Schnittstelle
Schnittstelle zur Herstellung einer Kommunikationsverbindung zwischen USV und
geschütztem Rechnersystem.
USV
Unterbrechungsfreie Stromversorgung.
34007117DE/AB - Seite 31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anhang
6.3 Stichwortregister
A
K
Abmessungen und Gewichte ........................................... 7
Kenndaten ...................................................................... 29
Kommunikationskarte ................................................ 8, 17
Kundenspezifische Anpassung ..................................... 20
Ausgang .................................................................21
Batterie .................................................................. 20
Ein/Aus-Bedingungen.............................................20
Alarmton (Summer) ........................................................ 19
Anschlüsse
Datenleitung ...........................................................16
RS232-Schnittstelle ................................................16
USB-Schnittstelle .................................................. 16
Ausschalten der USV über Software ............................. 20
Austausch des Batteriemoduls ......................... 22, 23, 24
Automatischer Neustart ................................................. 20
L
Leistungsschalter
Batterieschalter ........................................................ 8
Eingangsschalter ...................................................... 8
Leuchtanzeigen ................................................................9
B
Balkenanzeige ................................................................. 9
Batterie-Autonomiezeiten ............................................... 30
Batterie
P
Austausch..................................................... 22-23-24
Abschaltung am Ende der Autonomiezeit .............. 19
Recycling ................................................................ 27
Störung ..................................................................... 9
Umschaltung auf Batteriebetrieb ........................ 9, 19
Voralarm "Ende der Autonomiezeit" ....................... 19
Booster-Modus........................................................... 9, 18
Programmierbare Steckdosen .....................................8, 9
R
RS232-Schnittstelle .................................................. 8, 16
S
Sicherheit ...................................................................... 23
Sleep-Modus .................................................................. 20
Automatischer Neustart .......................................... 20
Störung der USV .............................................................. 9
D
Drucktasten ...................................................................... 9
F
Fader-Modus .............................................................. 9, 18
U
Überlast......................................................................9, 22
Umgebungstemperatur zu hoch .....................................29
Umweltschutz.................................................................27
UPS Driver .................................................. 18, 19, 20, 29
USB-Schnittstelle .......................................................8, 16
G
Gewicht ............................................................................7
I
Inbetriebnahme .............................................................. 18
W
Web Site........................................................................ 27
Seite 32 - 34007117DE/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
www.mgeups.com
MGE UPS SYSTEMS
Pulsar Evolution
1500 /1500 Rack
1100 /1100 Rack
800 /800 Rack
500 Rack
Manuale
d’installazione per
l’utente
W
O
O
O
S
L
I
I
T
O
Download from Www.Somanuals.com. All Manuals Search And Download.
Pagina 2 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduzione
Vi ringraziamo di aver scelto un prodotto MGE UPS SYSTEMS per la sicurezza delle vostre apparecchiature.
La gamma Pulsar Evolution è stata studiata con notevole cura per i singoli dettagli.
Per usufruire al meglio delle prestazioni della vostra unità UPS (gruppo statico di continuità), vi consigliamo di dedicare del
tempo alla lettura del presente manuale.
MGE UPS SYSTEMS presta una particolare attenzione all’impatto dei suoi prodotti sull’ambiente.
Le importanti risorse impiegate fanno di Pulsar Evolution un punto di riferimento in materia di protezione ambientale, in
particolare per quanto riguarda:
◗ L’approccio di ecoprogettazione nel corso del processo di sviluppo,
◗ Il riciclaggio di Pulsar Evolution al termine del ciclo di vita del prodotto.
Vi invitiamo a scoprire l’offerta MGE UPS SYSTEMS, nonché le opzioni della gamma Pulsar Evolution visitando il nostro
sito WEB all’indirizzo www.mgeups.it oppure contattando il vostro rappresentante MGE UPS SYSTEMS.
Importante: prima dell’installazione e dell’uso dell’UPS, è tassativo leggere attentamente le istruzioni di sicurezza fornite
(documento n° 3400722200).
34007117IT/AB - Pagina 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Premessa
Struttura della documentazione
La ricerca di informazioni si esegue principalmente in due modi:
◗ Tramite il sommario.
◗ Tramite l’indice analitico.
Convenzioni dei pittogrammi
Seguire tassativamente queste istruzioni.
Informazioni, consigli, aiuto.
Segnalazione visiva.
Azione.
Segnalazione acustica.
Le convenzioni adottate per rappresentare le spie all’interno delle illustrazioni sono le seguenti:
Spia spenta.
Spia accesa.
Spia lampeggiante.
Pagina 4 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Sommario
1. Presentazione
1.1 Viste generali............................................................................................................................... 7
Modelli "tower" ................................................................................................................................ 7
Modelli "slot" ................................................................................................................................... 7
1.2 Vista posteriore ........................................................................................................................... 8
1.3 Pannello di controllo .................................................................................................................... 9
2. Installazione
2.1 Apertura dell’imballaggio e verifica .......................................................................................... 10
Modelli "tower" .............................................................................................................................. 10
Modelli "slot" ................................................................................................................................. 11
2.2 Installazione ................................................................................................................................ 12
Modelli "tower" .............................................................................................................................. 12
Modelli "slot" 800/1100/1500......................................................................................................... 13
Modelli "slot" 500 .......................................................................................................................... 14
2.3 Collegamento delle apparecchiature ........................................................................................ 15
2.4 Collegamento della porta di comunicazione RS232 o USB (facoltativo) ................................ 16
2.5 Collegamento della protezione della linea dati (facoltativo) .................................................... 16
2.6 Installazione dell’opzione "scheda di comunicazione"........................................................... 17
3. Uso
3.1 Avviamento.................................................................................................................................. 18
3.2 Passaggio in modalità "booster" o "fader" (in caso di variazione di tensione della rete) ........ 18
3.3 Alimentazione a batteria (in caso di assenza della rete elettrica) .............................................. 19
Passaggio sulla batteria ................................................................................................................ 19
Soglia di allarme di fine autonomia batteria raggiunta .................................................................. 19
3.4 Personalizzazione (facoltativo) ................................................................................................... 20
Funzione ....................................................................................................................................... 20
Menù "Condizioni On/Off" ............................................................................................................. 20
Menù "Batteria" ............................................................................................................................. 20
Menù "Soglie di tensione" ............................................................................................................. 21
Menù "Sensibilità" ......................................................................................................................... 21
34007117IT/AB - Pagina 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Sommario
4. Manutenzione
4.1 Risoluzione avarie ...................................................................................................................... 22
4.2 Sostituzione del modulo batteria .............................................................................................. 23
Modelli "tower" .............................................................................................................................. 23
Modelli "slot" ................................................................................................................................. 25
5. Ambiente ..................................................................................................................27
6. Allegati
6.1 Caratteristiche tecniche ............................................................................................................. 28
Schema sinottico........................................................................................................................... 26
Caratteristiche tecniche ................................................................................................................ 29
Esempi di autonomia della batteria ............................................................................................... 30
6.2 Glossario ..................................................................................................................................... 31
6.3 Indice analitico ............................................................................................................................ 32
Pagina 6 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentazione
1.1 Viste generali
Modelli "tower"
Dimensioni in mm
(L x A x P)
P
Evolution 800
Evolution 1100
Evolution 1500
150 x 237 x 415
150 x 237 x 415
150 x 237 x 483
Peso in Kg
A
Evolution 800
Evolution 1100
Evolution 1500
10,5
11,5
15
P
U
L
S
A
R
Evolution
1
1
0
0
L
Modelli "slot"
Dimensioni in mm
(L x A x P)
P
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
438 x 43,5 x 353
438 x 43,5 x 499
438 x 43,5 x 499
A
438 x 43,5 x 522
(19") (1U)
P
U
L
S
A
R
Peso in Kg
Evolution
L
1500 Rack
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
9
15,5
16
19
34007117IT/AB - Pagina 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentazione
1.2 Vista posteriore
Pulsar Evolution 800 / 1100 / 1500
Pulsar Evolution 1500 :
7
Porta di comunicazione USB.
Porta di comunicazione RS232.
Protezione delle linee di dati.
1
2
3
4
8
5
4
5
Alloggiamento per l’opzione "scheda di
comunicazione".
2
1
2
6
1
Prese per il collegamento diretto delle
utenze.
6
7
Prese programmabili (1 e 2).
3
Interruttore di protezione della rete
elettrica di alimentazione.
Pulsar Evolution 500 / 800 / 1100 Rack
8
Presa per il collegamento alla rete
elettrica di alimentazione.
1
2
8
7
5
6
3
2
1
4
Pulsar Evolution 1500 Rack
1
2
4
8
7
2
1
3
5
6
Pagina 8 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentazione
1.3 Pannello di controllo
10
Pulsante luminoso di Accensione/Spegnimento (ON/OFF) delle prese di
uscita.
11
12
Funzionamento a batteria.
Difetto dell’apparecchio
Difetto della batteria.
13 UPS in sovraccarico.
Prese programmabili 1 alimentate.
14
1
2
15 Prese programmabili 2 alimentate.
16 Funzionamento in modalità "booster" o "fader".
17
Barra dei LED del livello di potenza utilizzata in uscita.
%
%
18
Barra dei LED del livello di carica della batteria.
Dal 76 al 100%.
Dal 51 al 75%.
Dal 26 al 50%.
Dallo 0 al 25%.
34007117IT/AB - Pagina 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installazione
2.1 Apertura dell’imballaggio e verifica
Modelli "tower"
20
21
22
23
24
P
U
L
S
A
R
Evolution
1
1
0
0
20 2 cavi per collegare le utenze.
21 Cavo di comunicazione RS 232.
22
23
Cavo di comunicazione USB.
CD ROM contenente i software "Solution Pac" e "UPS Driver".
24 Documentazione.
Pagina 10 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installazione
Modelli "slot"
20
21
22
23
25
24
26
P
U
L
S
A
R
Evolution
1500 Rack
20
2 cavi per collegare le utenze.
Cavo di comunicazione RS 232.
Cavo di comunicazione USB.
21
22
23
24
CD ROM contenente i software "Solution Pac" e "UPS Driver".
Documentazione.
25 Kit di montaggio all’interno di un armadio rack 19".
26
Sistema di fissaggio dei cavi di alimentazione delle utenze.
34007117IT/AB - Pagina 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installazione
2.2 Installazione
Modelli "tower"
P
U
L
S
A
R
Evolution
1
1
0
0
P
U
L
S
A
R
Evolution
1
1
0
0
Pagina 12 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installazione
Modelli "slot" 800/1100/1500
Montaggio e fissaggio delle guide e dello slot: seguire le tappe da 1 a 6.
2
1
6
2
2
4
3
5
2
P
U
L
S
A
R
Evolution
1500 Rack
6
5
3
Le viti di fissaggio e le guide sono fornite da MGE UPS SYSTEMS.
34007117IT/AB - Pagina 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installazione
Modelli "slot" 500
2
1
P
U
L
S
A
R
Evolution
1500 Rack
3
1
3
P
U
L
S
A
R
Evolution
1500 Rack
P
U
L
S
A
R
Evolution
1500 Rack
Pagina 14 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installazione
2.3 Collegamento delle utenze
Le istruzioni di seguito riportate sono illustrate utilizzando un modello Pulsar Evolution 1500 tower. Il principio è identico
per gli altri modelli tower e slot.
Verificare che le indicazioni riportate sulla targa di identificazione situata nella parte posteriore dell’apparecchio
corrispondano alla rete elettrica di alimentazione ed ai consumi elettrici reali delle utenze.
1 - Scollegare il cavo di alimentazione
dall’apparecchiatura.
8
2 - Collegare questo cavo(1) alla presa 8 ,
poi alla presa della rete elettrica di
alimentazione.
3 - Collegare le utenze all’UPS mediante i
cavi 20 .
Collegare preferibilmente le apparecchiature
prioritarie alle 2 prese
apparecchiature non prioritarie alle 2 prese
programmabili (1 e 2).
Per poter programmare l’arresto
delle prese in fase di
5
e le
6
2
1
6
autonomia della batteria ed
ottimizzare così la durata di tale
autonomia, è necessario utilizzare
il software di comunicazione MGE
UPS SYSTEMS.
6
5
4 - Chiudere il collegamento fissando il
sistema 26 (solo per i modelli slot).
20
Dopo la prima messa sotto tensione, è necessario attendere almeno 8 ore affinché la batteria possa fornire
l’autonomia nominale.
(1) Accertarsi che le caratteristiche di questo cavo
siano: 250V – 10A (sezione 1mm2, tipo H05).
34007117IT/AB - Pagina 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installazione
Le istruzioni di seguito riportate sono illustrate utilizzando un modello Pulsar Evolution 1500 tower. Il principio è identico
per gli altri modelli tower e slot.
2.4 Collegamento della porta di comunicazione RS232 o USB (facoltativo)
La porta di comunicazione RS232
e la porta di comunicazione USB
non possono funzionare
21
contemporaneamente.
1 - Collegare il cavo di comunicazione RS
232 21 o USB 22 alla porta seriale o USB
dell’apparecchiatura informatica.
RS232
2
1
22
2 - Collegare l’altra estremità del cavo di
comunicazione 21 o 22 alla porta di
comunicazione RS232
dell’UPS.
2
o USB
1
L’UPS è ora in grado di dialogare con un
software di amministrazione, di
configurazione o di sicurezza MGE UPS
SYSTEMS.
2.5 Collegamento della protezione della linea di dati (facoltativo)
La funzione "protezione delle linee di dati"
dell’UPS consente di eliminare le
sovratensioni veicolate sulle linee delle reti
informatiche.
Per ottenere questa funzione, far transitare
la linea da proteggere da parte dell’UPS
utilizzando le prese "Data line protection" IN
(ingresso) e OUT (uscita) come indicato
nella figura a lato (cavi RJ45 non forniti).
RS232
IN
OUT
DATA LINE
PROTECTION
Pagina 16 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installazione
2.6 Installazione dell’opzione "scheda di comunicazione"
1 - Rimuovere la piastra di copertura
4
4
dell’UPS fissata da 2 viti.
Alloggiamento ad accesso
limitato della scheda di
comunicazione.
2 - Inserire la scheda all’interno
dell’alloggiamento previsto.
3 - Fissare la piastra della scheda mediante
due viti.
RS232
DATA LINE PROTECTION
IN
OUT
Non è necessario arrestare il funzionamento dell’UPS per installare una scheda di comunicazione.
Questa operazione deve essere effettuata da personale qualificato.
34007117IT/AB - Pagina 17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Uso
3.1 Avviamento
Premere il pulsante 10 .
Il segnalatore acustico emette un bip e tutte le spie si accendono
contemporaneamente.
Il segnalatore acustico emette in seguito 2 bip durante l’autotest, poi il
pulsante 10 rimane acceso per segnalare l’alimentazione delle prese in
uscita.
- Rete elettrica di alimentazione presente: solo il pulsante 10 è
acceso. Le utenze sono alimentate dalla rete elettrica.
- Rete elettrica di alimentazione assente: il pulsante 10 et la spia
11 sono accese. Le utenze sono alimentate dall’UPS che funziona a
batteria.
10
11
12
1
2
%
%
Tutte le apparecchiature collegate sono sotto tensione.
Qualora la spia 10 o 11 non si accenda o qualora la spia 12 sia accesa, si è verificato un guasto (cfr. capitolo 4.1).
Nota bene: l’apparecchio ricarica la batteria dal momento in cui è collegato alla rete elettrica, anche senza premere il
pulsante 10 .
3.2 Passaggio in modalità "booster" o "fader"
(in caso di variazione di tensione della rete elettrica)
Le funzioni "booster" e "fader" consentono di mantenere la tensione di
uscita fornita dall’UPS all’interno di un campo definito attorno al valore
nominale, in caso di variazione dell’ampiezza più importante della rete
elettrica di alimentazione, il tutto senza scaricare la batteria.
I valori di tali campo di funzionamento sono configurabili per mezzo del
software "UPS Driver".
In caso di funzionamento in modalità "booster" o "fader", la spia 16 è
accesa, ad indicare una variazione di ampiezza importante della rete
1
2
elettrica di alimentazione.
16
%
%
Pagina 18 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Uso
3.3 Alimentazione a batteria (in caso di assenza della rete elettrica)
Passaggio sulla batteria
Qualora la rete elettrica di alimentazione sia fuori tolleranza, la spia 11
è accesa.
Nel corso di tutta durata dell’autonomia della batteria, il segnalatore
acustico emette un bip ogni 10 secondi.
11
Le utenze collegate all’UPS continuano ad essere alimentate grazie
alla batteria.
1
2
%
%
Soglia d’allarme di fine autonomia della batteria raggiunta
Quando tale soglia è raggiunta, il segnalatore acustico emette un bip
ogni 3 secondi.
Tale soglia può essere personalizzata per mezzo del software "UPS
Driver".
11
Rimane soltanto un breve lasso di autonomia della batteria,
chiudere le applicazioni poiché l’arresto automatico dell’UPS è
imminente.
1
2
%
Nel momento in cui si raggiunge la fine dell’autonomia della batteria,
l’UPS si arresta e tutte le spie sono spente.
%
Le utenze collegate all’UPS non sono più alimentate.
L’UPS si riavvia automaticamente al rientro della rete elettrica.
Nel caso in cui l’UPS non si riavvii, verificare che il riavvio automatico in seguito al ritorno della rete elettrica non sia stato
disattivato (cfr. capitolo 3.4 "Personalizzazione").
34007117IT/AB - Pagina 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Uso
3.4 Personalizzazione (facoltativo)
Funzione
È possibile far evolvere la personalizzazione per mezzo del software "UPS Driver", installato su un computer collegato
all’UPS secondo la procedura "Collegamento della porta di comunicazione RS232" (cfr. capitolo 2.4).
Verificare che il cavo RS 232 21 sia collegato.
Installazione del software "UPS Driver":
1 - Inserire il CD ROM "Solution Pac" contenente il software "UPS Driver" all’interno del lettore del computer, compatibile
Windows.
2 - Aprire Gestione Risorse di Windows o Explorer e selezionare il lettore CD ROM.
3 - Lanciare "\Emb\Evolutio\Config\Setup.exe".
Dopo aver installato "UPS Driver", è possibile modificare i seguenti parametri di regolazione:
Menù "Condizioni On/Off"
Funzioni personalizzabili
Predefinito in origine
Attivato
Personalizzazione possibile
Disattivato
Riavviamento automatico
Avviamento da batteria (cold start)
Arresto forzato
Attivato
Disattivato
Attivato
Disattivato
Disattivato
Attivato
Attivato
Standby
Avvio/Arresto inverter tramite software
Disattivato
Menù "Batteria"
Funzioni personalizzabili
Intervallo test batteria automatico
Soglia "Allarme livello basso" della batteria
Protezione dalle scariche profonde
Predefinito in origine
Tutte le settimane
Personalizzazione possibile
Tutti i giorni
Tutti i mesi
Nessun test
20% dell’autonomia rimanente
Attivato
Dal 10 al 40% dell’autonomia
rimanente
Disattivato
Pagina 20 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Uso
Menù "Soglie di tensione"
Funzioni personalizzabili
Predefinito in origine
230 V
Personalizzazione possibile
Tensione di uscita in funzionamento a batteria
Soglia alta di passaggio sulla batteria
200 V - 220 V - 240 V
da 271 a 294 V
da 244 a 265 V
da 184 a 207 V
da 160 a 180 V
Attivato(1)
294 V
Soglia di attivazione della modalità "fader"
Soglia di attivazione della modalità "booster"
Soglia bassa di passaggio sulla batteria
Campo massimo di tensione di ingresso
265 V
184 V
160 V
Disattivato
(1) Soglia bassa di passaggio sulla batteria = 150 V
Menù "Sensibilità"
Funzioni personalizzabili
Predefinito in origine
Personalizzazione possibile
Livello di sensibilità dell’UPS
Normale
Alta o bassa
Per maggiori informazioni riguardanti questi parametri consultare la rubrica Help del software "UPS Driver".
34007117IT/AB - Pagina 21
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Manutenzione
4.1 Risoluzione avarie
Risoluzione avarie senza intervento del Servizio Assistenza (tutti i modelli)
Sintomo
Diagnostica
Rimedio
La spia 13 lampeggia ed L’UPS è in sovraccarico. Il consumo elettrico delle
Verificare la potenza assorbita dalle
il segnalatore acustico
emette un bip.
apparecchiature collegate all’UPS supera la capacità di utenze e scollegare le
quest’ultimo.
apparecchiature non prioritarie.
La spia 12 lampeggia.
È stato individuato un difetto batteria durante il test
automatico della batteria.
Sostituire gli elementi batteria: vedi
il paragrafo 4.2.
Risoluzione avarie con intervento del Servizio Assistenza
Sintomo
Diagnostica
Rimedio
L’UPS presenta un guasto rilevato dall’elettronica
interna.
◗ Nessuna apparecchiatura è più alimentata.
La spia 12 si accende ed
il segnalatore acustico
emette un bip continuo.
Chiamare il Servizio Assistenza.
Le apparecchiature collegate all’UPS non
sono più protette.
Pagina 22 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Manutenzione
4.2 Sostituzione del modulo batteria
Richiamo sulle istruzioni di sicurezza:
La batteria presenta un rischio di elettrocuzione ed una corrente di cortocircuito elevata. Per qualsiasi intervento
sugli elementi della batteria, occorre prendere le seguenti precauzioni:
◗ Togliere orologi, anelli, fedi, braccialetti o qualsiasi altro oggetto metallico.
◗ Utilizzare utensili con impugnatura isolata.
Modelli "tower"
Smontaggio del modulo batteria
È possibile effettuare questa operazione senza arrestare l’UPS.
A
- Sganciare la piastra recante il logo
MGEUPS SYSTEMS sulla parte anteriore
dell'apparecchio.
B
C
- Svitare le due viti poste sul retro.
- Togliere la sezione di sinistra della
faccia anteriore sollevandola leggermente,
poi tirandola verso di sé.
C
P
U
L
S
A
R
Evolution
1
5
0
0
B
A
D
- Scollegare il blocco batteria tirando sui
connettori (non tirare mai sul cavo).
D
34007117IT/AB - Pagina 23
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Manutenzione
E
- Estrarre il blocco batteria tirando sulla
linguetta in plastica e procedere alla sua
sostituzione.
E
Rimontaggio del nuovo modulo batteria
Ripetere le operazioni sopra descritte in senso inverso.
◗ Attenzione: rischio di arco elettrico durante il collegamento della batteria.
◗ Per preservare la sicurezza e lo stesso livello di performance, utilizzare elementi batteria identici a quelli montati
nell’UPS.
◗ Badare ad inserire correttamente i componenti maschio e femmina del connettore durante il collegamento.
Pagina 24 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Manutenzione
Modelli "slot"
Smontaggio del modulo batteria
È possibile effettuare questa operazione senza arrestare l’UPS.
A
- Sganciare la piastra recante il logo
MGEUPS SYSTEMS sulla parte anteriore
dell'apparecchio.
B
C
- Svitare le due viti poste sul retro.
- Togliere la sezione di sinistra della
faccia anteriore, tirandola verso di sé.
PULSAR
Evolution
1
5
0
0
C
B
A
D
- Scollegare il blocco batteria tirando sui
connettori (non tirare mai sul cavo).
D
34007117IT/AB - Pagina 25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Manutenzione
E
- Rimuovere tale copertura.
E
F
- Estrarre il blocco batteria tirando sulla
linguetta in plastica e procedere alla sua
sostituzione.
F
Rimontaggio del nuovo modulo batteria
Ripetere le operazioni sopra descritte in senso inverso.
◗ Attenzione: rischio di arco elettrico durante il collegamento della batteria.
◗ Per preservare la sicurezza e lo stesso livello di performance, utilizzare elementi batteria identici a quelli montati
nell’UPS.
◗ Badare ad inserire correttamente i componenti maschio e femmina del connettore durante il collegamento.
Pagina 26 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Ambiente
Questo prodotto è progettato nel rispetto dell’ambiente:
Non contiene né CFC né HCFC.
Riciclaggio dell’UPS al termine della durata del ciclo di vita:
MGE UPS SYSTEMS si impegna a far ritrattare, per mezzo di società autorizzate e conformi alle normative vigenti, la
totalità dei prodotti recuperati al termine della durata del ciclo di vita (contattare la vostra agenzia).
Imballaggi:
Per il riciclaggio dell’imballaggio, conformarsi alle normative legali in vigore.
Avvertenza:
Questo prodotto contiene batterie al piombo. Il piombo è una sostanza pericolosa per l’ambiente qualora non sia riciclata
da società specializzate.
Sito web: www.mgeups.com
34007117IT/AB - Pagina 27
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Allegati
6.1 Caratteristiche tecniche
Schema sinottico
Filtro
Trasformatore "booster/fader"
Ingresso
Uscita
Inverter
Carica batterie
Batterie
Pagina 28 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Allegati
Caratteristiche tecniche
Pulsar Evolution
1500 / 1500 rack
500
1100 / 1100 rack
800 / 800 rack
1500 VA / 1000 W
Potenza di uscita
500 VA / 350 W
1100 VA / 700 W
800 VA / 560 W
Rete elettrica di
alimentazione
◗ Tensione
Monofase da 160 V a 294 V (1), 230V nominale.
da 47 Hz a 70 Hz (rete da 50 Hz) o da 56.5 Hz a 70 Hz (2) (rete da 60 Hz)
◗ Frequenza
Uscita in funzionamento
da batteria
◗ Tensione
◗ Frequenza
Monofase 230 V (3) (+6% / -10%)
50/60 Hz +/- 0,1 Hz
Batteria (Pb ermetico,
senza manutenzione)
◗ modello "tower"
3 x 12 V - 9 Ah,
6 x 6 V - 9 Ah
2 x 12 V - 9 Ah,
4 x 6 V - 9 Ah
2 x 12 V - 7,2 Ah,
4 x 6 V - 7,2 Ah
◗ modello "slot"
2 x 6 V - 9 Ah,
Ambiente
◗ Soglia di rumore (in
funzionamento da rete)
◗ Temperatura di
funzionamento
◗ Umidità
<40 dBA
0 a 35° C
20 a 90%
<40 dBA
0 a 40° C
20 a 90%
(senza condensa)
(1) Soglie alta e bassa regolabili mediante il software "UPS Driver".
(2) Fino a 40 Hz in modalità di sensibilità bassa (programmabile mediante il software "UPS Driver").
(3) Regolabile da 200 a 240 V mediante il software "UPS Driver".
34007117IT/AB - Pagina 29
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Allegati
Esempi di autonomie delle batterie
Pulsar Evolution 500
2 server ottimizzati slot
1 router
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 800
3 server ottimizzati slot
2 server di file/stampa
1 server + 1 router + 1 hub
1 router
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1100
3 server ottimizzati slot
2 server di file/stampa
1 server + 1 router + 1 hub
1 router
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1500
5 server ottimizzati slot
3 server di file/stampa
2 server + 1 router + 1 hub
1 router
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pagina 30 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Allegati
6.2 Glossario
Autonomia
Durata di funzionamento dell’apparecchio da batteria in caso di impossibilità di utilizzo
della rete elettrica di alimentazione.
Barra dei LED
Indicatore di potenza fornita o di autonomia della batteria sul pannello di controllo.
UPS scollegato fisicamente dalla rete elettrica di alimentazione.
Fuori tensione
Interruttore di ingresso
Modalità "booster"
Apparecchio di protezione della rete elettrica contro i guasti dell’UPS.
Modalità di funzionamento automatico dell’UPS che consente di aumentare la tensione
della rete elettrica, in caso di debolezza di quest’ultima, al di sopra di un valore definito
tramite la personalizzazione, il tutto senza scaricare la batteria.
Modalità "fader"
Modalità di funzionamento automatico dell’UPS che consente di abbassare la tensione
della rete elettrica, in caso di valore troppo elevato di quest’ultima, al di sopra di un
valore definito tramite la personalizzazione, il tutto senza scaricare la batteria.
Personalizzazione
Alcune funzioni dell’UPS possono essere modificate mediante il software "UPS Driver"
al fine di soddisfare meglio le necessità dell’utente.
Porta di comunicazione RS232 Consente di collegare l’UPS ad un computer tramite la porta di comunicazione seriale.
Porta di comunicazione USB
Prese di uscita
Consente di collegare l’UPS ad un computer tramite la porta di comunicazione USB.
Pulsar Evolution comporta 2 prese di uscita non programmabili.
Prese programmabili
Pulsar Evolution comporta 2 prese programmabili. Esse consentono
l’avviamento sequenziale delle apparecchiature protette, l’alleggerimento di applicazioni
non prioritarie in modalità batteria, o ancora la gestione delle priorità in fine autonomia
della batteria per conservare la più lunga autonomia delle apparecchiature più sensibili.
La programmazione di queste prese si esegue per mezzo del software Solution Pac
contenuto nel CD ROM in dotazione all’apparecchio.
Solution-Pac
Suite di software di amministrazione, di personalizzazione e di sicurezza MGE UPS
SYSTEMS contenuta nel CD ROM in dotazione all’apparecchio.
UPS
Gruppo statico di continuità.
UPS Driver
Software di comunicazione contenuto nel CD ROM in dotazione all’apparecchio che
consente di personalizzarlo in modo differente rispetto alla configurazione predefinita in
origine.
Utenze
Apparecchi o dispositivi collegati in uscita dell’UPS.
34007117IT/AB - Pagina 31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Allegati
6.3 Indice analitico
A
M
Ambiente ........................................................................ 27
Modalità Standby ........................................................... 20
Avvio automatico .................................................... 20
Modalità "booster" ...................................................... 9, 18
Modalità "fader" .......................................................... 9, 18
Arresto UPS tramite software ........................................ 20
Autonomia batteria ......................................................... 30
Avviamento .................................................................... 18
Avviamento automatico .................................................. 20
P
B
Personalizzazione ......................................................... 20
Batteria .................................................................. 20
Condizioni ON/OFF ................................................20
Uscita .................................................................... 21
Peso .................................................................................7
Porta di comunicazione RS232 ................................. 8, 16
Porta di comunicazione USB .....................................8, 16
Prese programmabili ....................................................8, 9
Pulsanti ............................................................................ 9
Barra dei LED .................................................................. 9
Batteria
Fine autonomia batteria.......................................... 19
Guasto ...................................................................... 9
Passaggio a batteria........................................... 9, 19
Riciclaggio .............................................................. 27
Soglia di allarme di fine autonomia ........................ 19
Sostituzione ..................................................22-23-24
C
Caratteristiche tecniche ................................................. 29
S
Collegamenti
Scheda di comunicazione ......................................... 8, 17
Segnalatore acustico ..................................................... 19
Sicurezza ...................................................................... 23
Sito web ........................................................................ 27
Sostituzione delle batterie ................................. 22, 23, 24
Sovraccarico ............................................................. 9, 22
Spie .................................................................................9
Standby ..........................................................................20
Linea di dati ........................................................... 16
Porta di comunicazione RS232 ..............................16
Porta di comunicazione USB..................................16
D
Dimensioni ....................................................................... 7
G
T
Guasto UPS ..................................................................... 9
Temperatura ambiente eccessiva ..................................29
I
U
Interruttore
Batteria ..................................................................... 8
Di ingresso ............................................................... 8
UPS Driver .................................................. 18, 19, 20, 29
Pagina 32 - 34007117IT/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
MGE UPS SYSTEMS
www.mgeups.com
Pulsar Evolution
1500 /1500 Rack
1100 /1100 Rack
800 /800 Rack
500 Rack
Manual de instalación
y utilización
W
O
O
O
S
L
I
I
T
O
Download from Www.Somanuals.com. All Manuals Search And Download.
Página 2 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Introducción
Le agradecemos que haya seleccionado un producto MGE UPS SYSTEMS para la seguridad de sus equipos.
La gama Pulsar Evolution ha sido fabricada con el más amplio cuidado.
Para aprovechar al máximo las prestaciones que le ofrece su SAI (Sistema de Alimentación Ininterrumpida), le
recomendamos que lea cuidadosamente este manual.
MGE UPS SYSTEMS está atento a los efectos que sus productos pudiesen causar en el medio ambiente.
Por ello, los recursos que se han puesto en obra hacen que Pulsar Evolution sea una referencia en materia de protección
del medio ambiente y particularmente:
◗ una acción de fabricación ecológica durante su ciclo de desarrollo,
◗ el reciclado de Pulsar Evolution al final de la vida útil del producto.
Le invitamos a que descubra la oferta de MGE UPS SYSTEMS, así como las opciones de la gama Pulsar Evolution
visitando nuestro sitio web: www.mgeups.com o poniéndose en contacto con su representante MGE UPS SYSTEMS.
Importante: antes de la instalación y utilización del SAI, es imperativo leer atentamente las consignas de seguridad
(documento n° 3400722200).
34007117ES/AB - Página 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Prólogo
Estructura de la documentación
La búsqueda de información se efectúa principalmente de dos maneras, a partir del:
◗ contenido,
◗ índice.
Convenciones de los pictogramas
Respetar imperativamente estas consignas.
Información, consejos, ayuda.
Señalización visual.
Acción.
Señalización acústica.
Los convenios adoptados para representar los indicadores luminosos en los dibujos son los siguientes:
Indicador luminoso apagado.
Indicador luminoso encendido.
Indicador luminoso intermitente.
Página 4 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Contenido
1. Presentación
1.1 Vistas generales.......................................................................................................................... 7
Modelos "torre" ............................................................................................................................... 7
Modelos "rack" ................................................................................................................................ 7
1.2 Caras traseras ............................................................................................................................. 8
1.3 Panel de control ............................................................................................................................ 9
2. Instalación
2.1 Desembalaje y verificación ........................................................................................................ 10
Modelos "torre" ............................................................................................................................. 10
Modelos "rack" .............................................................................................................................. 11
2.2 Instalación ................................................................................................................................... 12
Modelos "torre" ............................................................................................................................. 12
Modelos "rack" 800/1100/1500 ..................................................................................................... 13
Modelo "rack" 500 ......................................................................................................................... 14
2.3 Conexión de los equipamientos ................................................................................................ 15
2.4 Conexión del puerto de comunicación RS232 o USB (opcional) ............................................ 16
2.5 Conexión de la protección línea de datos (opcional) ............................................................... 16
2.6 Instalación de la opción "tarjeta de comunicación"................................................................ 17
3. Utilización
3.1 Puesta en funcionamiento ......................................................................................................... 18
3.2 Cambio a modo "booster" o "fader" (en caso de variación de tensión de la red eléctrica)...... 18
3.3 Alimentación con batería (en caso de ausencia de la red eléctrica) ......................................... 19
Cambio a batería .......................................................................................................................... 19
Umbral de alarma de fin de autonomía de la batería.................................................................... 19
3.4 Personalización (opcional) .......................................................................................................... 20
Función ......................................................................................................................................... 20
Ficha "condiciones On/Off" ........................................................................................................... 20
Ficha "Batería" .............................................................................................................................. 20
Ficha "Umbrales de tensión"......................................................................................................... 21
Ficha "Sensibilidad" ...................................................................................................................... 21
34007117ES/AB - Página 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contenido
4. Mantenimiento
4.1 Reparación .................................................................................................................................. 22
4.2 Cambio del módulo de batería................................................................................................... 23
Modelos "torre" ............................................................................................................................. 23
Modelos "rack" .............................................................................................................................. 25
5. Medio ambiente...............................................................................................................................27
6. Anexos
6.1 Características técnicas ............................................................................................................. 28
Esquema sinóptico........................................................................................................................ 26
Características técnicas ................................................................................................................ 29
Ejemplos de autonomías de batería ............................................................................................. 30
6.2 Glosario ....................................................................................................................................... 31
6.3 Indice............................................................................................................................................ 32
Página 6 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentación
1.1 Vistas generales
Modelos "torre"
Dimensiones en mm
(L x A x P)
P
Evolution 800
Evolution 1100
Evolution 1500
150 x 237 x 415
150 x 237 x 415
150 x 237 x 483
Peso en kg
A
Evolution 800
Evolution 1100
Evolution 1500
10,5
11,5
15
P
U
L
S
A
R
Evolution
1
1
0
0
L
Modelos "rack"
Dimensiones en mm
(L x A x P)
P
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
438 x 43,5 x 353
438 x 43,5 x 499
438 x 43,5 x 499
A
438 x 43,5 x 522
(19") (1U)
P
U
L
S
A
R
Peso en kg
Evolution
L
1500 Rack
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
9
15,5
16
19
34007117ES/AB - Página 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentación
1.2 Caras traseras
Pulsar Evolution 800 / 1100 / 1500
Pulsar Evolution 1500 :
7
Puerto de comunicación USB.
Puerto de comunicación RS232.
Protección de las líneas de datos.
1
2
3
4
8
5
4
5
Emplazamiento para la opción "tarjeta
de comunicación".
2
1
2
6
1
Tomas para la conexión de los
equipamientos.
6
7
Tomas programables (1 y 2).
3
Interruptor automático de protección de
la red eléctrica de alimentación.
Pulsar Evolution 500 / 800 / 1100 Rack
8
Toma para la conexión a la red
eléctrica de alimentación.
1
2
8
7
5
6
3
2
1
4
Pulsar Evolution 1500 Rack
1
2
4
8
7
2
1
3
5
6
Página 8 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Presentación
1.3 Panel de control
10
Botón luminoso Encendido/Apagado (ON/OFF) de las tomas de salida.
11
12
Funcionamiento con batería.
Defecto del aparato.
Defecto de la batería.
13 Sobrecarga del SAI.
Tomas programables 1 alimentadas.
14
1
2
15 Tomas programables 2 alimentadas.
16 Funcionamiento en modo "booster" o "fader".
17
Bargrafo del nivel de potencia utilizada en la salida.
%
%
18
Bargrafo del nivel de carga de la batería.
De 76 a 100%.
De 51 a 75%.
De 26 a 50%.
De 0 a 25%.
34007117ES/AB - Página 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Instalación
2.1 Desembalaje y verificación
Modelos "torre"
20
21
22
23
24
P
U
L
S
A
R
Evolution
1
1
0
0
20 2 cables para conectar los equipamientos.
21 Cable de comunicación RS232.
22
23
Cable de comunicación USB.
CD-ROM que contiene los software "Solución Pac" y "UPS Driver".
24 Documentación.
Página 10 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Instalación
Modelos "rack"
20
21
22
23
25
24
26
P
U
L
S
A
R
Evolution
1500 Rack
20
21
22
23
24
2 cables para conectar los equipamientos.
Cable de comunicación RS232.
Cable de comunicación USB.
CD-ROM que contiene los software "Solución Pac" y "UPS Driver".
Documentación.
25 Kit de montaje en armario 19".
26
Sistema de bloqueo de los cables de alimentación de los equipamientos.
34007117ES/AB - Página 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Instalación
2.2 Instalación
Modelos "torre"
P
U
L
S
A
R
Evolution
1
1
0
0
P
U
L
S
A
R
Evolution
1
1
0
0
Página 12 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Instalación
Modelos "rack" 800/1100/1500
Montaje y fijación de las guías y del rack: seguir las etapas de 1 a 6.
2
1
6
2
2
4
3
5
2
P
U
L
S
A
R
Evolution
1500 Rack
6
5
3
MGE UPS SYSTEMS entrega los tornillos de fijación y las guías.
34007117ES/AB - Página 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Instalación
Modelos "rack" 500
2
1
P
U
L
S
A
R
Evolution
1500 Rack
3
1
3
P
U
L
S
A
R
Evolution
1500 Rack
P
U
L
S
A
R
Evolution
1500 Rack
Página 14 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Instalación
2.3 Conexión de los equipamientos
Las consignas de abajo se ilustran con vistas de un modelo Pulsar Evolution 1500 "torre". El principio es idéntico en los
otros modelos "torre" y "rack".
Verificar que las indicaciones señaladas en la placa de identificación situada en la parte trasera del aparato
correspondan a la red eléctrica de alimentación y al consumo eléctrico real de los equipamientos.
1 - Desconectar el cable de alimentación del
equipamiento.
8
2 - Conectar este cable (1) en la toma
luego en la toma de la red eléctrica de
alimentación.
8
y
3 - Conectar los equipamientos al SAI con
los cables 20 .
Conectar de preferencia los equipamientos
prioritarios en las 2 tomas
5
y los
equipamientos no prioritarios en las 2 tomas
6
programables (1 y 2).
Para poder programar la parada
2
1
de las tomas
autonomía de la batería y
6
durante la
optimizar así la duración de esta
autonomía, se necesita acceder al
software de comunicación MGE
UPS SYSTEMS.
6
5
4 - Bloquear la conexión fijando el sistema
26 (en los modelos "rack" únicamente).
20
Después de la primera puesta bajo tensión, se necesitan al menos 8 horas para que la batería pueda suministrar la
autonomía nominal.
(1) Cerciorarse de que las características de este
cable son: 250V-10A (sección 1 mm2, tipo HO5).
34007117ES/AB - Página 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Instalación
Las consignas de abajo se ilustran con vistas de un modelo Pulsar Evolution 1500 "torre". El principio es idéntico en los
otros modelos "torre" y "rack".
2.4 Conexión del puerto de comunicación RS232 o USB (opcional)
El puerto de comunicación RS 232
21
y el puerto de comunicación USB
no pueden funcionar
simultáneamente.
1 - Conectar el cable de comunicación RS
232 21 o USB 22 en el puerto serie o
USB del equipo informático.
RS232
2
1
22
2 - Conectar el otro extremo del cable de
comunicación 21 o 22 en el puerto de
comunicación RS232
SAI.
2
o USB
1
del
A partir de este momento, el SAI puede
dialogar con un software de administración,
de personalización o de seguridad MGE
UPS SYSTEMS.
2.5 Conexión de la protección de la línea de datos (opcional)
La función "protección de las líneas de
datos" del SAI permite eliminar las
sobretensiones transmitidas en las líneas de
las redes informáticas.
Para ello, hacer transitar la línea que se
desea proteger por el SAI, utilizando las
tomas "Data línea protección" IN (entrada) y
OUT (salida) como se indica en la figura de
al lado (cables RJ45 no suministrados).
RS232
IN
OUT
DATA LINE
PROTECTION
Página 16 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Instalación
2.6 Instalación de la opción "tarjeta de comunicación"
1 - Retirar el protector
2 tornillos.
4
del SAI fijado con
4
Emplazamiento de la
tarjeta de comunicación,
con acceso restringido.
2 - Colocar la tarjeta en el lugar previsto.
3 - Fijar el protector de la tarjeta con 2
tornillos.
RS232
DATA LINE PROTECTION
IN
OUT
No se necesita apagar el SAI para instalar una tarjeta de comunicación.
Esta operación deberá ser efectuada por personal cualificado.
34007117ES/AB - Página 17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Utilización
3.1 Puesta en funcionamiento
Pulsar el botón 10 .
El zumbador emite un bip y todos los indicadores luminosos se
encienden simultáneamente.
10
11
12
El zumbador emite luego 2 bips durante el autotest y luego el botón 10
se queda encendido señalando la alimentación de las tomas de salida.
- Si la red eléctrica de alimentación está presente, sólo el botón 10
está encendido. Los equipamientos son alimentados mediante la red
eléctrica.
1
2
- Si la red eléctrica de alimentación está ausente, el botón 10 y el
indicador luminoso 11 están encendidos. En este caso, los
equipamientos son alimentados por el SAI que está funcionando con
batería.
%
%
El conjunto de los equipos conectados está bajo tensión.
Si los indicadores luminosos 10 o 11 no se encienden o si el indicador luminoso 12 está encendido, significa que existe
un defecto (ver capítulo 4.1).
Nota: el aparato recarga la batería inmediatamente después de conectarse a la red eléctrica, sin necesidad de pulsar el
botón 10 .
3.2 Cambio a modo "booster" o "fader"
(en caso de variación de tensión de la red eléctrica)
Las funciones "booster" y "fader" permiten mantener la tensión de salida
emitida por el SAI en un rango definido en torno al valor nominal, en
caso de variación de amplitud más importante de la red eléctrica de
alimentación y sin descargar la batería.
Se pueden configurar los valores de este rango de funcionamiento por
medio del software "UPS Driver".
Cuando el funcionamiento está en modo "booster" o "fader", el indicador
luminoso 16 está encendido, lo que indica una importante variación de
amplitud de la red eléctrica de alimentación.
1
2
16
%
%
Página 18 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Utilización
3.3 Alimentación con batería (en caso de ausencia de la red eléctrica)
Cambio a batería
Cuando la red eléctrica se encuentra fuera de tolerancias, el indicador
11 está encendido.
En toda la duración de autonomía de la batería, el zumbador emite un
bip cada 10 segundos.
11
Los equipos conectados al SAI siguen siendo alimentados por la
batería.
1
2
%
%
Umbral de alarma de fin de autonomía de la batería
Cuando se alcanza ese umbral, el zumbador emite un bip cada 3
segundos.
El umbral de alarma puede personalizarse con el software "UPS Driver".
Sólo queda muy poca autonomía en la batería, por lo que se
deberán cerrar las aplicaciones, ya que queda muy poco tiempo
antes de que el SAI se apague automáticamente.
11
1
2
Cuando se termina la autonomía de batería, el SAI se apaga y todos los
indicadores luminosos se apagan.
%
%
Los equipos conectados al SAI dejan de estar alimentados.
El SAI arranca automáticamente cuando vuelve la red eléctrica
Si el SAI no se enciende, compruebe que el arranque automático por reanudación de la red eléctrica no esté desactivado
(ver capítulo 3.4 "Personalización").
34007117ES/AB - Página 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Utilización
3.4 Personalización (opcional)
Función
Se pueden modificar los parámetros de personalización del SAI con el software "UPS Driver" instalado en el ordenador
conectado al SAI según el procedimiento "Conexión del puerto de comunicación RS232" (ver capítulo 2.4).
Verificar que el cable RS 232 21 esté conectado.
Instalación del software "UPS Driver":
1 - Insertar el CD ROM "Solución Pac" que contiene el software "UPS Driver" en el lector de su ordenador compatible
Windows.
2 - Abrir el gestor de archivos Windows o el explorador y seleccionar el lector de CD ROM.
3 - Lanzar "\Emb\Evolutio\Config\Setup.exe".
Después de haber instalado "UPS Driver", usted podrá modificar los siguientes parámetros de reglaje:
Ficha "Condiciones On/Off"
Funciones personalizables
Configuración de fábrica
Activado
Personalización posible
Desactivado
Inicio automático
Inicio con batería (cold star)
Paro forzado
Activado
Desactivado
Activado
Desactivado
Desactivado
Activado
Activado
Puesta en reposo
Desactivado
Encendido/Paro ondulador con software
Ficha "Batería"
Funciones personalizables
Intervalo de la prueba automática de la batería
Umbral "Alarma nivel bajo" de la batería
Protección contra descargas profundas
Configuración de fábrica
Cada semana
Personalización posible
Diario
Cada mes
Sin prueba
20% de autonomía restante
Activado
de 10 a 40%
de autonomía restante
Desactivado
Página 20 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Utilización
Ficha "Umbrales de tensión"
Funciones personalizables
Configuración de fábrica
Personalización posible
200 V - 220 V - 240 V
271 a 294 V
Tensión de salida en funcionamiento con batería
Umbral superior de cambio a batería
Umbral de activación del modo "fader"
Umbral de activación del modo "booster"
Umbral inferior de cambio a batería
230 V
294 V
265 V
244 a 265 V
184 V
184 a 207 V
160 V
160 a 180 V
Rango máximo de tensión de entrada
Desactivado
Activado (1)
(1) Umbral inferior de cambio a batería = 150 V
Ficha "Sensibilidad"
Funciones personalizables
Configuración de fábrica
Personalización posible
Nivel de sensibilidad del SAI
Normal
Alto o bajo
Para más informaciones sobre estos parámetros, ver el apartado "Ayuda" del "UPS Driver".
34007117ES/AB - Página 21
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Mantenimiento
4.1 Reparación
Reparación sin intervención del servicio posventa (todos los modelos)
Síntoma
Diagnóstico
Solución
El indicador 13 se
enciende y el zumbador
emite un bip.
El SAI se está sobrecargando. El consumo eléctrico de Comprobar la potencia absorbida
los equipamientos conectados al SAI excede la
capacidad de este último.
por los equipos y desconectar
aquellos que no sean prioritarios.
El indicador 12 parpadea Se detectó un defecto de la batería durante la prueba
automática de la misma.
Reemplazar los elementos de
batería: ver el párrafo 4.2.
Reparación con intervención del servicio posventa
Síntoma
Diagnóstico
Solución
El indicador 12 se
enciende y el zumbador
emite sonidos acústicos
continuos.
El SAI presenta un defecto detectado por la
electrónica interna.
◗ El conjunto de equipos ha dejado de ser alimentado. Llamar al servicio posventa.
Los equipos conectados al SAI ya no están
protegidos.
Página 22 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Mantenimiento
4.2 Cambio del módulo batería
Recapitulación de las consignas de seguridad:
La batería presenta un riesgo de electrocución y una elevada corriente de cortocircuito. Se deberán tomar las
precauciones siguientes para cualquier intervención que se realice en los elementos de la batería:
◗ Quitarse reloj, anillos, alianzas, brazaletes o cualquier otro objeto metálico,
◗ Utilizar herramientas con mango aislado.
Modelos "torre"
Desmontaje del módulo batería
Esta operación puede efectuarse sin tener que parar el SAI.
A
- Retirar la placa con el logotipo MGE
situada en la cara delantera del aparato.
- Destornillar los dos tornillos situados
detrás de la placa.
- Retirar la sección izquierda de la cara
B
C
delantera levantándola ligeramente y luego
tirándola hacia usted.
C
P
U
L
S
A
R
Evolution
1
5
0
0
B
A
D
- Desconectar el bloque de batería
tirando de los conectadores (no tire nunca
de los cables).
D
34007117ES/AB - Página 23
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Mantenimiento
E
- Extraer el bloque de batería tirando de
la lengüeta de plástico y proceder a su
cambio.
E
Montaje del nuevo módulo de la batería
Realizar en sentido inverso las operaciones que se describen arriba.
◗ Atención: riesgo de arco eléctrico durante la conexión de la batería.
◗ Para preservar la seguridad y el mismo nivel de eficacia, utilizar elementos de batería idénticos a los que están
montados en el SAI.
◗ Cuidar en meter a fondo las partes macho y hembra del conector al realizar la conexión.
Página 24 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Mantenimiento
Modelos "rack"
Desmontaje del módulo batería
Esta operación puede efectuarse sin tener que parar el SAI.
A
- Retirar la placa con el logotipo MGE
situada en la cara delantera del aparato.
B
- Destornillar los dos tornillos situados
detrás de la placa.
- Retirar la sección izquierda de la cara
delantera tirándola hacia usted.
C
PULSAR
Evolution
1
5
0
0
C
B
A
D
- Desconectar el bloque de batería
tirando de los conectadores (no tire nunca
de los cables).
D
34007117ES/AB - Página 25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Mantenimiento
E
- Levantar ese capó.
E
F
- Extraer el bloque de batería tirando de
la lengüeta de plástico y proceder a su
cambio.
F
Montaje del nuevo módulo de la batería
Realizar en sentido inverso las operaciones que se describen arriba.
◗ Atención: riesgo de arco eléctrico durante la conexión de la batería.
◗ Para preservar la seguridad y el mismo nivel de eficacia, utilizar elementos de batería idénticos a los que están
montados en el SAI.
◗ Cuidar en meter a fondo las partes macho y hembra del conector al realizar la conexión.
Página 26 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Medio Ambiente
Este producto ha sido diseñado para respetar el medio ambiente:
No contiene CFC ni HCFC.
Reciclado del SAI al final de su funcionamiento útil:
MGE UPS SYSTEMS se compromete a utilizar los servicios de sociedades autorizadas y conformes con la reglamentación
para que retiren el conjunto de productos recuperados al final de su vida útil (póngase en contacto con su agencia).
Embalaje:
Para el reciclado del embalaje, confórmese con las exigencias legales en vigor.
Aviso:
Este producto contiene baterías de plomo. El plomo es una substancia peligrosa para el medio ambiente si no es reciclado
por organismos especializados.
Sitio Web : www.mgeups.com
34007117ES/AB - Página 27
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anexos
6.1 Características técnicas
Esquema sinóptico
Filtro
Transformador "booster/fader"
Entrada
Salida
Ondulador
Cargador
Batería
Página 28 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anexos
Características técnicas
Pulsar Evolution
1500 / 1500 rack
500
800 / 800 rack
1100 / 1100 rack
1500 VA / 1000 W
Potencia de salida
500 VA / 350 W
800 VA / 560 W
1100 VA / 700 W
Red eléctrica de
alimentación
◗ Tensión
Monofásica 160 V a 294 V (1), 230V nominal
47 Hz a 70 Hz (red 50 Hz) o 56,5 Hz a 70 Hz (2) (red 60 Hz)
◗ Frecuencia
Salida utilización en
funcionamiento con
batería
◗ Tensión
Monofásica 230 V (3) (+6% / -10%)
50/60 Hz +/- 0,1 Hz
◗ Frecuencia
Batería (Plomo estanco,
sin mantenimiento)
◗ modelos "torre"
3 x 12 V - 9 Ah,
6 x 6 V - 9 Ah
2 x 12 V - 7,2 Ah,
4 x 6 V - 7,2 Ah
2 x 12 V - 9 Ah,
4 x 6 V - 9 Ah
◗ modelos "rack"
2 x 6 V - 9 Ah,
Medio ambiente
◗ Nivel de ruido
<40 dBA
0 a 35° C
20 a 90%
<40 dBA
0 a 40° C
20 a 90%
(funcionamiento con red)
◗ Temperatura de
funcionamiento
◗ Humedad
(sin condensación)
(1) Umbrales superior e inferior ajustables por el software "UPS Driver".
(2) Hasta 40 Hz en modo de sensibilidad baja (programable por el software "UPS Driver").
(3) Ajustable de 200 a 240 V por el software "UPS Driver".
34007117ES/AB - Página 29
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anexos
Ejemplos de autonomías de batería
Pulsar Evolution 500
2 servidores optimizados rack
1 clasificador
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 800
3 servidores optimizados rack
2 servidores de ficheros/de
impresión
1 servidor + 1 clasificador + 1 Hub
1 clasificador
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1100
3 servidores optimizados rack
2 servidores de ficheros/de
impresión
1 servidor + 1 clasificador + 1 Hub
1 clasificador
1 Hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1500
5 servidores optimizados rack
3 servidores de ficheros/de
impresión
2 servidores + 1 clasificador
+ 1 Hub
1 clasificador
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Página 30 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anexos
6.2 Glosario
Autonomía
Duración de funcionamiento del aparato con la batería en caso de imposibilidad de
utilización de la red eléctrica de alimentación.
Bargrafo
Indicador de potencia suministrada o de autonomía de la batería en el panel de control.
Aparatos o dispositivos conectados en las salida del SAI.
Equipamientos
Fuera de tensión
SAI desconectado físicamente de la red eléctrica de alimentación.
Aparato de protección de la red eléctrica contra los defectos del SAI.
Interruptor automático
de entrada
Modo "booster"
Modo de funcionamiento automático del SAI que permite subir la tensión de la red
eléctrica, en caso de que esté baja, por encima de un valor definido en los parámetros
de personalización, sin tener que descargar la batería.
Modo "fader"
Modo de funcionamiento automático del SAI que permite bajar la tensión de la red
eléctrica, en caso de que tenga un valor muy elevado, por abajo de un valor definido en
los parámetros de personalización, sin tener que descargar la batería.
Personalización
Algunas funciones del SAI pueden modificarse MEDIANTE el software "UPS Driver"
para satisfacer mejor las necesidades del usuario.
Puerto de comunicación RS232 Permite conectar el SAI a un ordenador a través del puerto de comunicación serie.
Puerto de comunicación USB Permite conectar el SAI a un ordenador a través del puerto de comunicación USB.
SAI
Sistema de Alimentación Ininterrumpida.
Solución Pac
Serie de programas de administración, personalización y de seguridad MGE UPS
SYSTEMS contenida en el CD ROM que se entrega con el aparato.
Tomas de salida
Pulsar Evolution cuenta 2 tomas de salida no programables.
Tomas programables
Pulsar Evolution cuenta 2 tomas programables. Permiten el inicio
secuencial de los equipamientos protegidos, la desconexión de aplicaciones no
prioritarias en modo batería o incluso la gestión de prioridades al final de autonomía de
la batería para conservar la mayor autonomía en los equipamientos más sensibles. La
programación de estas tomas se hace mediante el software "Solution Pac" que se
encuentra en el CD ROM que se entrega con el aparato.
UPS Driver
Software de comunicación contenido en el CD ROM que se entrega con el aparato y
permite personalizar los parámetros de manera diferente a la configuración de fábrica.
34007117ES/AB - Página 31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Anexos
6.3 Indice
A
P
Arranque automático ...................................................... 20
Autonomía de la batería ................................................. 30
Paro del SAI por software ..............................................20
Personalización ............................................................. 20
Batería ....................................................................20
Condiciones On/Off ................................................20
Salida .................................................................... 21
Peso .................................................................................7
Puerto de comunicación RS232 ............................... 8, 16
Puerto de comunicación USB ................................... 8, 16
Puesta en funcionamiento ............................................. 18
Puesta en reposo ........................................................... 20
Inicio automático .................................................... 20
Pulsadores ....................................................................... 9
B
Bargrafo ........................................................................... 9
Batería
Cambio a batería ................................................ 9, 19
Cambio del módulo batería .......................... 22-23-24
Defecto ..................................................................... 9
Fin de autonomía de la batería .............................. 19
Reciclado................................................................ 27
Umbral de alarma de fin de autonomía .................. 19
R
C
Reposo ...........................................................................20
Cambio de las baterías ..................................... 22, 23, 24
Características técnicas ................................................. 29
Conexiones
S
Seguridad ...................................................................... 23
Sitio web ........................................................................27
Sobrecarga ................................................................9, 22
Línea de datos....................................................... 16
Puerto de comunicación RS232 ............................ 16
Puerto de comunicación USB ................................16
T
D
Tarjeta de comunicación ............................................8, 17
Temperatura ambiente excesiva ................................... 29
Tomas programables .................................................. 8, 9
Defecto SAI ...................................................................... 9
Dimensiones .................................................................... 7
I
U
Indicadores luminosos .................................................... 9
Interruptor automático
UPS Driver .................................................. 18, 19, 20, 29
batería ...................................................................... 8
de entrada ................................................................ 8
Z
Zumbador ....................................................................... 19
M
Medio ambiente ............................................................. 27
Modo "booster" .......................................................... 9, 18
Modo "fader" .............................................................. 9, 18
Página 32 - 34007117ES/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
www.mgeups.com
MGE UPS SYSTEMS
Pulsar Evolution
1500 /1500 Rack
1100 /1100 Rack
800 /800 Rack
500 Rack
Installatie- en
gebruikershandleiding
W
O
O
O
S
L
I
I
T
O
Download from Www.Somanuals.com. All Manuals Search And Download.
Pagina 2 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Inleiding
Wij danken u voor uw keuze van een MGE UPS SYSTEMS product om uw apparatuur te beveiligen.
De Pulsar Evolution-reeks is met de grootste zorg ontwikkeld.
Voor een optimaal gebruik van uw UPS (Uninterruptible Power Supply – Ononderbroken Stroomvoorziening) adviseren wij
u deze gebruikershandleiding aandachtig te lezen.
MGE UPS SYSTEMS besteedt veel aandacht aan de invloed van zijn producten op het milieu.
De aandacht die is besteed aan de milieu aspecten maken van de Pulsar Evolution dé referentie op dit gebied:
◗ milieubewuste benadering tijdens het hele productontwikkelingsproces,
◗ recycleren van de Pulsar Evolution aan het einde van zijn levensduur.
Ontdek de Pulsar Evolution-reeks en alle andere MGE UPS SYSTEMS producten door onze web site te bezoeken:
www.mgeups.com of contact op te nemen met uw MGE UPS SYSTEMS dealer.
Belangrijk: Vooraleer UPS te installeren en te gebruiken, is het noodzakelijk om aandachtig de veiligheidsinstructies te
lezen (document n° 340072200).
34007117NL/AB - Pagina 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Voorwoord
Indeling van de documentatie
Er zijn twee manieren om informatie op te zoeken:
◗ via de inhoudsopgave,
◗ via de index.
Verklaring der tekens
Deze instructies moeten strikt inachtgenomen worden.
Informatie, tips, hulp.
Visueel signaal.
Handeling.
Geluidssignaal.
De status van de LED’s wordt als volgt weergegeven:
LED uit.
LED aan.
LED knippert.
Pagina 4 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
Inhoudsopgave
1. Beschrijving
1.1 Algemeen overzicht .................................................................................................................... 7
"Tower" modellen ............................................................................................................................ 7
"Rack" modellen.............................................................................................................................. 7
1.2 Achterzijde................................................................................................................................... 8
1.3 Bedieningspaneel ......................................................................................................................... 9
2. Installeren
2.1 Uitpakken en controleren ........................................................................................................... 10
"Tower" modellen .......................................................................................................................... 10
"Rack" modellen............................................................................................................................ 11
2.2 Installatie ..................................................................................................................................... 12
"Tower" modellen .......................................................................................................................... 12
800/1100/1500 "rack" modellen .................................................................................................... 13
500 "rack" model ........................................................................................................................... 14
2.3 Aansluiten van de te beveiligen apparatuur............................................................................. 15
2.4 Aansluiten van de RS232- of USB-communicatiepoort (optioneel) ........................................ 16
2.5 Aansluiten van de beveiliging van datalijnen (optioneel) ....................................................... 16
2.6 Aanbrengen van de optionele "communicatiekaart" .............................................................. 17
3. Gebruik
3.1 Inschakelen ................................................................................................................................. 18
3.2 Overschakelen op "booster" of "fader" functie
(bij spanningsvariaties op het netstroomcircuit) ............................................................................ 18
3.3 Energievoorziening door batterij (bij afwezigheid van netstroomcircuit) .................................. 19
Overschakelen op batterij ............................................................................................................. 19
Alarmgrens einde autonomie batterij bereikt ................................................................................ 19
3.4 Specifieke programmering (optioneel)....................................................................................... 20
Functie .......................................................................................................................................... 20
Indexkaart "Aan/Uit"-functies ........................................................................................................ 20
Indexkaart "Batterij" ...................................................................................................................... 20
Indexkaart "Spanningsdrempels" .................................................................................................. 21
Indexkaart "Gevoeligheid"............................................................................................................. 21
34007117NL/AB - Pagina 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Inhoudsopgave
4. Onderhoud
4.1 Storingen verhelpen ................................................................................................................... 22
4.2 Batterijmodule vervangen .......................................................................................................... 23
"Tower" modellen .......................................................................................................................... 23
"Rack" modellen............................................................................................................................ 25
5. Milieu.................................................................................................................................................... 27
6. Bijlagen
6.1 Technische specificaties ............................................................................................................ 28
Overzichtsschema ........................................................................................................................ 26
Technische specificaties ............................................................................................................... 29
Voorbeelden van batterij-autonomie ............................................................................................. 30
6.2 Woordenlijst ................................................................................................................................ 31
6.3 Index............................................................................................................................................. 32
Pagina 6 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Beschrijving
1.1 Algemeen overzicht
"Tower" modellen
Afmetingen in mm
(breedte x hoogte x diepte)
D
Evolution 800
150 x 237 x 415
150 x 237 x 415
150 x 237 x 483
Evolution 1100
Evolution 1500
Gewicht in kg
H
Evolution 800
Evolution 1100
Evolution 1500
10,5
11,5
15
P
U
L
S
A
R
Evolution
1
1
0
0
B
"Rack" modellen
Afmetingen in mm
(breedte x hoogte x diepte)
D
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
438 x 43,5 x 353
438 x 43,5 x 499
438 x 43,5 x 499
H
438 x 43,5 x 522
(19") (1U)
P
U
L
S
A
R
Gewicht in kg
Evolution
B
1500 Rack
Evolution 500 Rack
Evolution 800 Rack
Evolution 1100 Rack
Evolution 1500 Rack
9
15,5
16
19
34007117NL/AB - Pagina 7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Beschrijving
1.2 Achterzijde
Pulsar Evolution 800 / 1100 / 1500
Pulsar Evolution 1500:
7
USB-communicatiepoort.
RS232-communicatiepoort.
Beveiliging van datalijnen.
1
2
3
4
8
5
4
5
6
7
8
Ruimte gereserveerd voor optionele
"communicatiekaart".
2
1
2
6
1
Aansluitingen voor aansluiten van de te
beveiligen apparatuur.
Programmeerbare aansluitingen
(1 en 2).
3
Schakelaar voor beveiliging van het
netstroomcircuit.
Pulsar Evolution 500 / 800 / 1100 Rack
Aansluiting voor netaansluiting.
1
2
8
7
5
6
3
2
1
4
Pulsar Evolution 1500 Rack
1
2
4
8
7
2
1
3
5
6
Pagina 8 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Beschrijving
1.3 Bedieningspaneel
10 Verlichte aan/uit-knop (ON/OFF) van de uitgangsaansluitingen.
Werking op batterij.
11
12
Fout elektronica.
Fout batterij.
UPS overbelast.
13
14
15
16
Programmeerbare aansluitingen 1 onder spanning.
Programmeerbare aansluitingen 2 onder spanning.
Werking in "booster" of "fader" functie.
1
2
17 Display van het niveau van het aan de uitgang afgenomen vermogen.
%
%
18
Display van het laadniveau van de batterij.
76 tot 100%.
51 tot 75%.
26 tot 50%.
0 tot 25%.
34007117NL/AB - Pagina 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installeren
2.1 Uitpakken en controleren
"Tower" modellen
20
21
22
23
24
P
U
L
S
A
R
Evolution
1
1
0
0
20 Twee kabels voor aansluiting van uw apparatuur.
21 RS232-communicatiekabel.
22
23
USB-communicatiekabel.
CD-ROM met de "Solution Pac" en "UPS Driver" software.
24 Documentatie.
Pagina 10 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installeren
"Rack" modellen
20
21
22
23
25
24
26
P
U
L
S
A
R
Evolution
1500 Rack
20
21
22
23
Twee kabels voor aansluiting van uw apparatuur.
RS232-communicatiekabel.
USB-communicatiekabel.
CD-ROM met de "Solution Pac" en "UPS Driver" software.
Documentatie.
24
25 Set voor montage in 19"-rack.
26
Steun voor plaatsing in verticale stand.
34007117NL/AB - Pagina 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installeren
2.2 Installatie
"Tower" modellen
P
U
L
S
A
R
Evolution
1
1
0
0
P
U
L
S
A
R
Evolution
1
1
0
0
Pagina 12 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installeren
800/1100/1500 "rack" modellen
Monteren en bevestigen van rails en rack: volg stap 1 tot 6.
2
1
6
2
2
4
3
5
2
P
U
L
S
A
R
Evolution
1500 Rack
6
5
3
De bevestigingsschroeven en rails worden door MGE UPS SYSTEMS geleverd.
34007117NL/AB - Pagina 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installeren
500 "rack" model
2
1
P
U
L
S
A
R
Evolution
1500 Rack
3
1
3
P
U
L
S
A
R
Evolution
1500 Rack
P
U
L
S
A
R
Evolution
1500 Rack
Pagina 14 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installeren
2.4 Aansluiten van de te beveiligen apparatuur
Op de illustratie bij de onderstaande instructies is de Pulsar Evolution 1500 "tower" te zien. Maar het principe is hetzelfde
voor alle “tower” en “rack” modellen.
Controleer of de specificaties op het typeplaatje aan de achterzijde van het apparaat overeenkomen met uw
netspanning en het werkelijke stroomverbruik van de aangesloten apparatuur.
1 - Koppel de voedingskabel van de
apparatuur los.
8
2 - Sluit deze kabel (1) aan op de aansluiting
8 en vervolgens op de wandcontactdoos.
3 - Sluit de te beveiligen apparatuur op de
UPS aan met behulp van de kabels 20 .
Sluit bij voorkeur de primaire apparatuur aan
op de 2 aansluitingen
apparatuur op de 2 programmeerbare
aansluitingen (1 en 2).
De aansluitingen
5
en de secundaire
6
6
kunnen
tijdens batterij-autonomie in de off-
positie worden gezet om de duur
van de autonomie te optimaliseren.
Dit kan echter alleen via de MGE
UPS SYSTEMS
2
1
communicatiesoftware worden
geprogrammeerd.
6
5
4 - Vergrendel de aansluitingen met behulp
van onderdeel 26 (alleen bij “rack”
modellen).
20
Na de eerste keer inschakelen duurt het minstens 8 uur voordat de batterij de nominale autonomie kan leveren.
(1) Controleer of deze kabel de volgende
specificaties heeft: 250V-10A (diameter 1 mm2,
type HO5).
34007117NL/AB - Pagina 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installeren
Op de illustraties bij de onderstaande instructies is de Pulsar Evolution 1500 "tower" te zien. Maar het principe is
hetzelfde voor alle “tower” en “rack” modellen.
2.4 Aansluiten van de RS232- of USB-communicatiepoort (optioneel)
De RS232- en de USB-
21
communicatiepoort kunnen niet
tegelijkertijd functioneren.
1 - Sluit de RS232-communicatiekabel 21
of de USB-communicatiekabel 22 aan op
de seriële of de USB-poort van de
computerapparatuur.
RS232
2
1
22
2 - Sluit het andere uiteinde van de
communicatiekabel 21 of 22 aan op de
RS232-communicatiepoort
2
of de USB-
communicatiepoort van de UPS.
1
De UPS kan nu communiceren met een
beheer-, programmeer- of
beveiligingssoftware van MGE UPS
SYSTEMS.
2.5 Aansluiten van de beveiliging van de datalijn (optioneel)
Deze beveiligingsfunctie van de UPS zorgt
voor het opheffen van de overspanningen
die via de computernetwerklijnen lopen.
Laat de te beveiligen lijn via de UPS lopen
door de kabels aan te sluiten op de "Data
line protection" aansluitingen IN (ingang) en
OUT (uitgang), zoals aangegeven op het
schema hiernaast (RJ45-kabels niet
meegeleverd).
RS232
IN
OUT
DATA LINE
PROTECTION
Pagina 16 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installeren
2.6 Aanbrengen van de optionele "communicatiekaart"
1 - Verwijder het afdekplaatje
4
van de
4
UPS dat met twee schroeven bevestigd is.
Plaatsing van de
communicatiekaart, met
beperkte toegang.
2 - Schuif de kaart in de daarvoor bestemde
ruimte.
3 - Bevestig het afdekplaatje van de kaart
met behulp van de 2 schroeven.
RS232
DATA LINE PROTECTION
IN
OUT
De UPS hoeft niet uitgeschakeld te worden om een communicatiekaart te installeren.
Deze operatie moet worden uitgevoerd door gekwalificeerd personeel.
34007117NL/AB - Pagina 17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Gebruik
3.1 Inschakelen
Druk op knop 10 .
De buzzer laat een biep horen en alle LED’s gaan tegelijkertijd branden.
De buzzer laat dan 2 bieps horen tijdens de zelftest en vervolgens blijft
knop 10 branden om te signaleren dat er spanning is op de
aansluitingen aan de uitgang.
10
11
12
- Als de netspanning aanwezig is: brandt alleen knop 10 .
De apparatuur krijgt stroom van het netstroomcircuit.
- Als de netspanning afwezig is: branden knop 10 en LED 11 .
De apparatuur krijgt stroom van de UPS die op batterij werkt.
1
2
%
%
Alle aangesloten apparatuur is nu onder spanning.
Als LED 10 of 11 niet gaat branden, of als LED 12 brandt, is er een fout aanwezig (zie hoofdstuk 4.1).
N.B.: het apparaat laadt de batterij op zodra hij op de netspanning is aangesloten, zelfs als er niet op knop 10 gedrukt
3.2 Overschakelen op "booster" of "fader" functie
(in geval van spanningswisselingen op het netstroomcircuit)
De "booster" en "fader" functies maken het mogelijk de door de UPS
geleverde uitgangsspanning bij grote spanningswisselingen op het net
binnen een bepaalde tolerantie rondom de nominale waarde te houden,
en dit zonder de batterij te ontladen.
Deze tolerantiewaarden kunnen worden geprogrammeerd via de "UPS
Driver" software.
Als de "booster" of "fader" functie actief is, brandt LED 16 om te
signaleren dat er grote spanningswisselingen op het netstroomcircuit
1
2
zijn.
16
%
%
Pagina 18 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Gebruik
3.3 Energievoorziening door batterij (bij afwezigheid van de netspanning)
Overschakelen op batterij
Als de netspanning buiten toleranties is, brandt LED 11 .
Tijdens ontlading van de batterij laat de buzzer om de 10 seconden een
biep horen.
De op de UPS aangesloten apparatuur blijft stroom krijgen van de
batterij.
16
1
2
%
%
Alarmgrens einde autonomie batterij bereikt
Als de alarmgrens bereikt is laat de buzzer om de 3 seconden een biep
horen.
Deze alarmgrens kan klantspecifiek worden ingesteld via de “UPS
Driver” software.
16
De batterij heeft dan nog maar een geringe autonomie, en sluit alle
toepassingen want de UPS gaat weldra automatisch uitschakelen.
1
2
Als het einde van de batterij-autonomie bereikt is, schakelt de UPS uit
en zijn alle LED’s uit.
%
%
De op de UPS aangesloten apparatuur krijgt geen stroom meer.
De UPS schakelt automatisch weer in bij terugkeer van de netspanning.
Als de UPS niet automatisch weer inschakelt, moet gecontroleerd worden of de automatische inschakelfunctie bij terugkeer
van de netspanning niet uitgeschakeld is (zie hoofdstuk 3.4 “Specifieke programmering”).
34007117NL/AB - Pagina 19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Gebruik
3.4 Specifieke programmering (optioneel)
Functie
De specifieke programmering van de UPS kan verder worden aangepast door middel van de "UPS Driver" software, via
een computer die op de UPS is aangesloten volgens de procedure "Aansluiten van de RS232-communicatiepoort" (zie
hoofdstuk 2.4).
Controleer of de RS232-kabel 21 aangesloten is.
Installeren van de "UPS Driver" software:
1 - Doe de "Solution Pac" CD-ROM met de "UPS Driver" software in de CD-ROM drive van uw PC (onder WINDOWS).
2 - Open de Windows file manager of explorer en klik op de CD-ROM drive.
3 - Start "\Emb\Evolutio\Config\Setup.exe".
Na het installeren van "UPS Driver" kunt u de volgende specifieke opties invoeren:
Tabblad "Aan/Uit"-functies
Specifiek te programmeren functies
Fabrieksprogrammering
Specifieke programmering
Niet actief
Automatisch inschakelen
Inschakelen op batterij ("cold start")
Geforceerde uitschakeling
Actief
Actief
Niet actief
Actief
Niet actief
Overschakelen op pauze
Niet actief
Actief
Actief
In/Uitschakelen omvormer via software
Niet actief
Tabblad "Batterij"
Specifiek te programmeren functies
Tijdsperiode voor automatische batterijtest
Alarmgrens "Lage batterijstand"
Fabrieksprogrammering
Elke week
Specifieke programmering
Elke dag
Elke maand
Geen test
Resterende autonomie 20%
Actief
Resterende autonomie 10 tot 40%
Beveiliging tegen vergaande batterijontlading
Niet actief
Pagina 20 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Gebruik
Tabblad "Spanningsdrempels"
Specifiek te programmeren functies
Fabrieksprogrammering
Specifieke programmering
200 V - 220 V - 240 V
271 tot 294 V
Uitgangsspanning (bij werking op batterij)
Bovendrempel voor overschakelen op batterij
Drempel voor activeren "fader" functie
Drempel voor activeren "booster" functie
Onderdrempel voor overschakelen op batterij
Maximaal bereik ingangsspanning
230 V
294 V
265 V
244 tot 265 V
184 V
184 tot 207 V
160 V
160 tot 180 V
Niet actief
Actief(1)
(1) Onderdrempel voor overschakelen op batterij = 150 V
Tabblad "Gevoeligheid"
Specifiek te programmeren functies
Fabrieksprogrammering
Specifieke programmering
Gevoeligheidsniveau van de UPS
Normaal
Hoog of laag
Voor meer informatie over deze parameters, zie de helprubriek van de "UPS Driver" software.
34007117NL/AB - Pagina 21
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Onderhoud
4.1 Storingen verhelpen
Storingen verhelpen zonder hulp van de servicedienst (alle modellen).
Storing
Oorzaak
Oplossing
LED 13 gaat branden en De UPS is overbelast. Het energieverbruik van de
Controleer het door de apparatuur
de buzzer laat een biep
horen.
aangesloten apparatuur is groter dan de UPS aankan. opgenomen vermogen en koppel de
minder belangry apparatuur los.
LED 12 knippert.
Tijdens de automatische batterijtest is een batterijfout
gedetecteerd.
Vervang de batterij-elementen: zie
paragraaf 4.2.
Storingen verhelpen met hulp van de servicedienst.
Storing
Oorzaak
Oplossing
De UPS vertoont een fout die gedetecteerd wordt door
het interne elektronische systeem.
◗ De aangesloten apparatuur krijgt geen stroom meer. Neem contact op met de
LED 12 gaat branden en
de buzzer biept continu.
servicedienst.
De op de UPS aangesloten apparatuur is niet
meer beveiligd.
Pagina 22 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Onderhoud
4.2 Batterijmodule vervangen
Herhaling van veiligheidsinstructies:
De batterij kan elektrische schokken veroorzaken en heeft een hoge kortsluitstroom. De volgende
voorzorgsmaatregelen moeten genomen worden bij elk ingrijpen op de batterij-elementen:
◗ Altijd eerst horloges, ringen, trouwringen, armbanden en alle andere metalen voorwerpen afdoen.
◗ Altijd gereedschap gebruiken waarvan het handvat geïsoleerd is.
"Tower" modellen
Demonteren van de batterijmodule
Dit kan worden uitgevoerd zonder de UPS uit te schakelen.
A
- Verwijder het plaatje met het "MGE
UPS SYSTEMS" logo op de voorkant van
het apparaat.
B
C
- Draai de twee schroeven erachter los.
- Verwijder het linkervoorpaneel door het
voorzichtig op te heffen en naar u toe te
trekken.
C
P
U
L
S
A
R
Evolution
1
5
0
0
B
A
D
- Het batterijblok verwijderen door aan
de stekker te trekken (nooit aan de kabels
trekken).
D
34007117NL/AB - Pagina 23
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Onderhoud
E
- Het batterijblok verwijderen door aan
een plastic tongetje te trekken en dan
vervangen.
E
Monteren van een nieuwe batterijmodule
Doe hetzelfde als hierboven beschreven maar nu in omgekeerde volgorde.
◗ Opgelet: risico voor lichtboog, wanneer de batterij er wordt ingestopt.
◗ Gebruik voor optimale veiligheid en dezelfde prestaties altijd dezelfde batterij-typen als die in de UPS zijn
gemonteerd.
◗ Zorg er bij het aansluiten voor dat de mannelijke en vrouwelijke delen van de connector goed ingedrukt zijn.
Pagina 24 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Onderhoud
"Rack" modellen
Demonteren van de batterijmodule
Dit kan worden uitgevoerd zonder de UPS uit te schakelen.
A
- Verwijder het plaatje met het "MGE
UPS SYSTEMS" logo op de voorkant van
het apparaat.
B
C
- Draai de twee schroeven erachter los.
- Verwijder het linkervoorpaneel door het
voorzichtig naar u toe te trekken.
PULSAR
Evolution
1
5
0
0
C
B
A
D
- Het batterijblok verwijderen door aan
de stekker te trekken (nooit aan de kabels
trekken).
D
34007117NL/AB - Pagina 25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Onderhoud
E
- Verwijder het beschermpaneel.
E
F
- Het batterijblok verwijderen door aan
een plastic tongetje te trekken en dan
vervangen.
F
Monteren van een nieuwe batterijmodule
Doe hetzelfde als hierboven beschreven maar nu in omgekeerde volgorde.
◗ Opgelet: risico voor lichtboog, wanneer de batterij er wordt ingestopt.
◗ Gebruik voor optimale veiligheid en hetzelfde prestatieniveau altijd dezelfde batterij-elementen als die in de UPS
zijn gemonteerd.
◗ Zorg er bij het aansluiten voor dat de mannelijke en vrouwelijke delen van de connector goed ingedrukt zijn.
Pagina 26 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Milieu
Dit product werd milieubewust ontwikkeld:
Het bevat geen CFK of HCFK.
Recycleren van de UPS aan het einde van zijn levensduur:
MGE UPS SYSTEMS verplicht zich ertoe de afvalverwerking van alle producten die aan het einde van hun levensduur
worden ingezameld te laten uitvoeren door gecertificeerde, conform de regelgeving werkende bedrijven (neem contact op
met uw dealer).
Verpakking:
Neem voor de afvalverwerking van de verpakking strikt de geldende wet- en regelgeving in acht.
Waarschuwing:
Dit product bevat loodbatterijen. Lood is een stof die schadelijk is voor het milieu als hij niet door gespecialiseerde
afvalverwerkingsdiensten wordt gerecycleerd.
Web site: www.mgeups.com
34007117NL/AB - Pagina 27
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Bijlagen
6.1 Technische specificaties
Overzichtsschema
Filter
"Booster/fader"-transformator
Ingang
Uitgang
Omvormer
Lader
Batterij
Pagina 28 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Bijlagen
Technische specificaties
Pulsar Evolution
1500 / 1500 rack
500
800 / 800 rack
1100 / 1100 rack
1500 VA / 1000 W
Vermogen aan uitgang
500 VA / 350 W
1100 VA / 700 W
800 VA / 560 W
Netstroom
◗ Spanning
◗ Frequentie
eenfasig 160 V tot 294 V (1), 230V nominaal
47 Hz tot 70 Hz (net 50 Hz) of 56,5 Hz tot 70 Hz (2) (net 60 Hz)
Belasting aan uitgang bij
werking op batterij
◗ Spanning
eenfasig 230 V (3) (+6% / -10%)
50/60 Hz +/- 0,1 Hz
◗ Frequentie
Batterij (onderhoudsvrij
lood)
◗ "Tower" modellen
◗ "Rack" modellen
2 x 12 V - 9 Ah,
4 x 6 V - 9 Ah
3 x 12 V - 9 Ah,
6 x 6 V - 9 Ah
2 x 12 V - 7,2 Ah,
4 x 6 V - 7,2 Ah
2 x 6 V - 9 Ah,
Milieu
◗ Geluidsniveau (bij werking
op netspanning)
◗ Bedrijfstemperatuur
◗ Vochtigheid
<40 dBA
0 tot 35° C
20 tot 90%
<40 dBA
0 tot 40° C
20 tot 90%
(zonder condensatie)
(1) Boven- en onderdrempel kunnen worden geprogrammeerd met de "UPS Driver" software.
(2) Tot 40 Hz indien ingesteld op lage gevoeligheid (programmeerbaar met de "UPS Driver" software).
(3) Instelbaar van 200 tot 240V met de "UPS Driver" software.
34007117NL/AB - Pagina 29
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Bijlagen
Voorbeelden van batterij-autonomie
Pulsar Evolution 500
2 geoptimaliseerde rack servers
1 router
1 hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 800
3 geoptimaliseerde rack servers
2 printerbestand servers
1 server + 1 router + 1 hub
1 router
1 hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1100
3 geoptimaliseerde rack servers
2 printerbestand servers
1 server + 1 router + 1 hub
1 router
1 hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pulsar Evolution 1500
5 geoptimaliseerde rack servers
3 printerbestand servers
2 servers + 1 router + 1 hub
1 hub
0
10
20
30
40
50
60
70
80
90 100 110 120 t (min)
Pagina 30 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Bijlagen
6.2 Woordenlijst
Aansluitingen aan de uitgang Pulsar Evolution heeft 2 niet programmeerbare aansluitingen aan de uitgang.
Apparatuur
Apparaten of systemen die op de uitgangen van de UPS zijn aangesloten.
Autonomie
Werkingsduur op batterij wanneer de netspanning niet beschikbaar is.
"Booster" functie
Automatische bedrijfstoestand van de UPS waarmee de netspanning, als deze te laag
is, verhoogd kan worden tot boven een specifiek te programmeren waarde, en dit
zonder de batterij te ontladen.
Buiten spanning
Display
UPS mechanisch losgekoppeld van het netstroomcircuit.
Indicatie van geleverd vermogen en autonomie batterij op het bedieningspaneel.
"Fader" functie
Automatische bedrijfstoestand van de UPS waarmee de netspanning, als deze te hoog
is, verlaagd kan worden tot onder een specifiek te programmeren waarde, en dit zonder
de batterij te ontladen.
Ingangsschakelaar
Beveiliging van het netstroomcircuit tegen de fouten van de UPS.
Programmeerbare
aansluitingen
Pulsar Evolution 2 groepen met ieder 2 programmeerbare aansluitingen. Hiermee kan
de beveiligen apparatuur per groep in- en uitgeschakeld worden. Zodoende kunnen
de diverse verbruikers sequentieel ingeschakeld worden en bij batterijbedrijf voortijdig
worden uitgeschakeld om de autonomie van de primaire verbruikers te verlengen. Deze
aansluitingen kunnen geprogrammeerd worden met behulp van de Solution-
Pac software op de CD-ROM die met het apparaat wordt meegeleverd.
RS232-communicatiepoort
Solution-Pac
Maakt het mogelijk de UPS op een computer aan te sluiten via de seriële
communicatiepoort.
Serie beheer-, programmeer- en beveiligingssoftware van MGE UPS SYSTEMS op de
CD-ROM die bij het apparaat geleverd wordt.
Specifieke programmering
Bepaalde functies van de UPS kunnen via de "UPS Driver" software worden afgestemd
op specifieke behoeften.
UPS
Uninterruptible Power Supply (Ononderbroken Stroomvoorziening).
UPS Driver
Communicatiesoftware op de CD-ROM die bij het apparaat geleverd wordt, waarmee de
fabrieksprogrammering aan specifieke behoeften kan worden aangepast.
USB- communicatiepoort
Maakt het mogelijk de UPS op een computer aan te sluiten via de USB-
communicatiepoort.
34007117NL/AB - Pagina 31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Bijlagen
6.3 Index
A
M
Milieu .............................................................................. 27
Aansluitingen
Gegevensverbinding ..............................................16
RS232-communicatiepoort .....................................16
USB-communicatiepoort ....................................... 16
Afmetingen ....................................................................... 7
Automatisch inschakelen ............................................... 20
Autonomie batterij .......................................................... 30
O
Omgevingstemperatuur te hoog ................................... 29
Overbelasting .............................................................9, 22
Overschakelen op pauze ............................................... 20
Automatisch opnieuw schakelen ............................ 20
B
Batterij
P
Pauze .............................................................................20
Programmeerbare aansluitingen ................................. 8, 9
Alarmgrens einde autonomie ................................. 19
Einde autonomie batterij......................................... 19
Fout .......................................................................... 9
Overschakelen op batterij................................... 9, 19
Recycleren ............................................................. 27
Vervanging ................................................... 22-23-24
"Booster" functie ........................................................ 9, 18
Buzzer ............................................................................ 19
R
RS232-communicatiepoort ....................................... 8, 16
S
Schakelaar
Batterij- ..................................................................... 8
Ingangs- ................................................................... 8
Specifieke programmering .............................................20
Aan/Uit-functies ......................................................20
Batterij ....................................................................20
Uitgang .................................................................. 21
C
Communicatiekaart .................................................... 8, 17
D
Display ............................................................................. 9
T
F
Technische specificaties ................................................ 29
"Fader" functie ........................................................... 9, 18
Fout UPS ......................................................................... 9
U
Uitschakelen van de UPS door software .......................20
UPS Driver .................................................. 18, 19, 20, 29
USB-communicatiepoort ............................................8, 16
G
Gewicht ............................................................................7
I
V
Inschakelen .................................................................... 18
Veiligheid ........................................................................23
Vervanging van batterijen ................................. 22, 23, 24
K
Knoppen........................................................................... 9
W
Website ..........................................................................27
L
LED’s............................................................................... 9
Pagina 32 - 34007117NL/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
340071170/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
3400711700/AB
Download from Www.Somanuals.com. All Manuals Search And Download.
MGE UPS SYSTEMS
Nothing will stop you now
140, Avenue Jean Kuntzmann
ZIRST - Montbonnot St Martin
38334 - Saint Ismier Cedex - France
www.mgeups.com
3400711700-AB
Download from Www.Somanuals.com. All Manuals Search And Download.
|
KWC Outdoor Shower Shower Arm User Manual
La Crosse Technology Clock Radio WS 8007U User Manual
LG Electronics Range LRG3093SB User Manual
Life Fitness Home Gym CMFCO User Manual
Life Fitness Stepper Machine Lifestride 5500 User Manual
Maverick Ventures Thermometer OT 01 User Manual
Maytag Cooktop W10268401A User Manual
McCulloch Lawn Mower M65H53SD User Manual
Melissa Hot Beverage Maker 745193 User Manual
MEY Equipment Lawn Mower Residential Cylinder Mower User Manual