Elite-5m HD
Operation manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that of the receiver
Consult the dealer or an experienced technician for help
WARNING: When a GPS unit is used in a vehicle, the vehicle operator is solely responsible for operating
the vehicle in a safe manner. Vehicle operators must maintain full surveillance of all pertinent driving or
boating conditions at all times. An accident or collision resulting in damage to property, personal injury or
death could occur if the operator of a GPS-equipped vehicle fails to pay full attention to travel conditions
and vehicle operation while the vehicle is in motion.
Download from Www.Somanuals.com1. All Manuals Search And Download.
Table of contents
Goto cursor..............................................9
Advanced Mode ......................................9
Restore defaults ......................................9
Pages.............................................. 10
Steer Page.............................................10
Chart Page ............................................10
Overlay Data.......................................... 11
Chart Operation ............................. 13
Chart Menu............................................13
Waypoints, Routes, Trails......................14
Routes Screen.......................................16
Introduction...................................... 4
Unit Controls............................................4
Inserting microSD cards ..........................5
Basic Operation............................... 6
Setup wizard............................................6
Page menus ............................................6
Accessing the Settings menu..................7
Accessing menu items.............................7
Working with menus ................................7
Entering text ............................................8
Cursor......................................................8
Table of Contents | Elite-5m HD
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Trails Screen .........................................19
Orientation.............................................21
Chart Settings........................................22
Overlay Data..........................................22
Settings..................................................22
Navigation Settings ...................................24
Settings .......................................... 26
Settings menu........................................26
System...................................................26
Saving Screenshots...............................28
Alarms ...................................................28
Specifications ................................ 30
Index............................................... 31
Table of Contents | Elite-5m HD
3
Download from Www.Somanuals.com. All Manuals Search And Download.
introduction
Getting Started
unit Controls
To turn on/off the unit, press and
hold the LiGht/Power key for
three seconds.
LiGht/Power: controls backlight level
and turns unit on/off
Turn unit on/
off
KeYPAD: controls cursor & selects items
Press the zoom in and zoom out
keys at the same time to set a Man
Overboard waypoint. Your system
will automatically create an active
route back to the MOB waypoint. You
must cancel navigation to terminate
the function.
on menus
Man
Overboard
waypoint
PAGeS: allows you to select a page to
view
menu: opens settings, context and page
menus
enter: finalizes menu selections; save
waypoint at cursor position
Adjusting
the
backlight
This unit has 11 backlight levels.
Press the LiGht/Power key to
switch backlight levels.
moB: press and hold both Zoom keys to
create a Man Overboard waypoint
zoom KeYS: (+) used to zoom in; (-) used
to zoom out
Select Audio from the System menu.
Select Mute and press enter.
Muting
Audio
microSD slot: insert a blank microSD card to save
screen captures, waypoints, routes and trails; or
insert a microSD mapping card to use mapping
data
Select GPS from the System settings
Selecting a
GPS source
menu. Press menu
,
select GPS
source and choose the desired source.
Introduction | Elite-5m HD
4
Download from Www.Somanuals.com. All Manuals Search And Download.
inserting microSD cards
Carefully slide the microSD card into the slot until it clicks into place.
To remove, carefully push in the card until it clicks out of place.
Introduction | Elite-5m HD
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Page menus
Basic Operation
The Steer and Chart pages have menus that can
only be accessed when those pages are displayed.
Setup wizard
The Setup wizard will appear when the unit is
turned on for the first time. To choose your own
settings, do not run the setup wizard. To restart the
Setup wizard, restore defaults.
Chart menu
Chart page
Pages
This unit has two pages: Steer and Chart. Press the
pages key to switch pages.
Steer menu
Steer page
Basic Operation | Elite-5m HD
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the Settings menu
Working with menus
There are several menu types used to make
adjustments to options and settings, including
scrollbars, on/off features and dropdown menus.
Scrollbars
Select the scrollbar and press the
keypad left (decrease) or right
(increase).
Accessing menu items
The keypad and enter key are used to select
menu items and open submenus. Use the keypad
to highlight the desired item and press enter.
On/Off features
Select the on/off item and
press enter to turn it
on/off.
Basic Operation | Elite-5m HD
7
Download from Www.Somanuals.com. All Manuals Search And Download.
To input text:
1. Use the keypad to select the desired
Dropdown menus
Select the dropdown menu
and press the keypad up/
down to select the desired
item. Press enter.
character and press enter.
2. Repeat Step 1 for each character.
3. When entry is completed, highlight OK
and press enter.
nOte: Press the Menu key to exit
menus.
Switches letters
to uppercase/
lowercase
Dialogs
Dialogs are used for user input
or for presenting information to
the user. Depending on the type
of information or entry, different
methods are used to confirm,
cancel or close the dialog.
Switches keyboard
between ALPHA and
QWERTY layout
Cursor
The keypad moves the cursor around the display,
allowing you to scroll the map and select map
items.
entering text
Some functions, like naming a waypoint, route or
trail, will require you to input text.
Press Menu and select Return to vessel or Exit
cursor mode to clear the cursor.
Basic Operation | Elite-5m HD
8
Download from Www.Somanuals.com. All Manuals Search And Download.
goto cursor
Standby mode
Used to navigate to the cursor.
Lowers power consumption by turning off the
display.
1. Move the cursor to a desired location
and press Menu.
1. Press the PWr/Light
key to access the Back-
light dialog.
2. Select Goto cursor and press enter.
2. Select Standby and
press enter.
Advanced Mode
3. Press any key to resume normal
operation.
Enables advanced features and settings.
The following features are enabled when Advanced
mode is turned on:
nOte: Leaving your unit in Standby
mode when your motor is turned off will
run down your battery.
•
Navigation (Enables arrival radius, off-
course distance and Bearings setting)
•
Alarms (Enables arrival, off course and
anchor alarm options)
•
•
NMEA 0183 configuration options
restore defaults
Units (Enables distance, speed and Sets unit options and settings to default values.
bearings configuration options)
Basic Operation | Elite-5m HD
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Course over ground
Waypoint
Compass
Direction to destination
Current location
Cursor
Current location
Current location and distance/
bearing to cursor
Zoom
Range
Navigation
information
Chart Page
Steer Page
Consists of map that moves in real-time as you
move. By default, the map is shown from a birds-
eye view with North at the top of the screen.
The Steer page has a compass that shows your
current track, the direction to your destination, and
a digital data navigation panel.
Pages | Elite-5m HD
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Overlay Data
Used to select data shown on the Chart page.
To add overlay data:
1. From the Chart page, press Menu.
2. Select Overlay data and press enter.
3. Select Configure and press enter.
Overlay data
Show
4. Press Menu and select Add. Press
enter.
Enables/disables the display of overlay data,
allowing you to remove overlay data from the
screen without deleting the current overlay data
configuration.
5. Select a data category and press
enter.
6. Select the desired data and press
enter.
7. Repeat Steps 5 and 6 to add more data.
8. Press Menu and select Return to
Overlays. Press enter.
Configure
9. Press Menu, select Done Configuring
Allows you to select/customize overlay data.
and press enter.
Pages | Elite-5m HD
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Customizing Overlay Data
You can select a data source, add/remove data and
adjust the size and position of overlay data on the
screen.
Select the desired overlay
data
from the “Configure
Item Locations and Sizes
dialog” and press Menu.
The configuration menu will
appear.
Pages | Elite-5m HD
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart Operation
Chart menu
Chart Menu
New Waypoint
Press Menu from the Chart page to open the Chart
menu. Press enter to launch the New waypoint
dialog.
Creates a waypoint at your current location or at the
cursor position. When the cursor is on the screen,
waypoints will be saved at the cursor position. If
the cursor is not active, waypoints will be saved at
your current position.
Chart Operation | Elite-5m HD
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3. To measure from the cursor position to
a new location, press enter and move
the cursor to a new location.
Find
Used to search for chart
categories from the cursor
position or from your current
position.
4. To stop measuring, press Menu and
select Stop measuring.
Measure
Waypoints, routes, trails
The cursor can be used to measure the distance
between two items on the chart.
Used to create, edit, navigate and delete waypoints,
routes and trails.
Press the keypad left/right to toggle between
waypoints, routes and trails tabs.
To measure distance:
1. Select Measure and press enter.
2. Move the cursor to the desired location.
The distance will be shown in the
measuring dialog.
Waypoints Screen
Waypoints menu
Chart Operation | Elite-5m HD
14
Download from Www.Somanuals.com. All Manuals Search And Download.
New
Creates a new waypoint
at the cursor or vessel
position. You can also select
waypoint name, icon and
latitude/longitude from the
new waypoint dialog.
Show
Displays the selected waypoint
on the map.
Waypoints
menu
Goto
Allows you to navigate to a waypoint.
Edit
Delete and Delete All
Allows you to edit the name,
icon and latitude/longitude
of a selected waypoint.
Delete is used to delete a
selected waypoint. Delete
All deletes all waypoints.
Chart Operation | Elite-5m HD
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Inserts waypoint between
existing route waypoints
Sort
Controls how the waypoints list will be
sorted — by name or by nearest.
Adds waypoint to
end of the route
routes Screen
Used to create, edit, navigate and delete routes.
Use the keypad to highlight the Routes tab to ac-
cess the Routes screen.
Route waypoint
menu
Starts navigation
to the selected
route waypoint
To create a route from waypoint list:
1. Press Menu from the Routes screen.
2. Select New... and press enter.
Routes menu
Routes screen
Creating a route
Routes can be created by inserting waypoints from
the waypoints list or by using the cursor to posi-
tion new points on the chart. You also can add way-
points to a route by selecting them from the chart
screen.
3. Press the keypad down to select the
Leg Name field and press enter.
4. Press Menu, select Add to End and
press enter.
Chart Operation | Elite-5m HD
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Leg Name field
Creating a route using points from chart:
1. Repeat Steps 1-4 from the instructions
for Creating a route from waypoint list.
2. Select Points using chart and press
enter. The chart page will appear.
3. Move the cursor to the desired location.
Press enter to set a point.
4. Repeat Step 3 to add more points.
5. Highlight Waypoint from list and press
5. Press Menu and select Stop adding.
enter.
Press enter.
6. Select the desired waypoint and press
6. Select Save and press enter.
enter.
7. Press Menu and select Add to end to
Navigating a route
add another waypoint to the route.
Routes can be navigated in forward or reverse.
8. When the route is complete, press
Menu, select Stop Editing and press
enter.
1. Select the desired route on the Route
screen and press Menu.
9. Select Save and press enter.
2. Select Start and press enter.
Chart Operation | Elite-5m HD
17
Download from Www.Somanuals.com. All Manuals Search And Download.
To cancel navigation:
3. Select Forward or Reverse and press
enter.
1. Press Menu from the chart screen.
2. Select Navigation and press enter.
3. Highlight Cancel and press enter.
4. Select Yes and press enter.
4. Press Menu and select Return to Chart.
Press enter.
Edit and New Route dialogs
Used to edit/create routes, route names and to turn
on/off the route display.
Displays/hides
route on the map
To edit/create a route, use the
keypad to select the Route
Leg Name field and press
enter.
Routes menu
Chart Operation | Elite-5m HD
18
Download from Www.Somanuals.com. All Manuals Search And Download.
To access the “Edit” or “New Route” dialog, select
Edit or New on the Routes dialog and press
enter.
trails Screen
Used to create, edit, navigate and delete trails. Use
the keypad to highlight the Trails tab to access the
Trails screen.
To finalize changes on the “Edit” or “New Route”
dialogs, highlight the Done button and press
enter.
Displayed
Used to show/hide a route on the display, which
prevents the screen from being cluttered by too
many routes.
Trails menu
Trails screen
Creating trails
Delete and Delete All
When creating a trail you can customize the trail
name and color from the New Trail.
Delete is used to delete
individual routes. Delete
All, removes all routes.
Chart Operation | Elite-5m HD
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit and New Trail dialogs
Allows you to edit/create trails, select trails names,
trail color, trail display and the trail being recorded.
You can also convert a trail into a route from the
Edit Trails dialog.
Trails menu
Turns on/
off trail
Turns on/
off trail
recording
display
on map
To create a trail:
Edit Trails dialog
1. Select New and press enter. The
New Trail dialog will appear.
2. Select Save and press enter.
Chart Operation | Elite-5m HD
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigating a trail
Displayed and Record
A trail must be saved as a route before it can be Displayed allows you to show/hide trails on the
navigated.
map display, preventing the screen from being
cluttered with trails.
To save a trail as a route:
The Record command allows you to record or
resume recording a desired trail.
1. Highlight the desired trail on the Trails
screen and press enter. The Edit
Trail menu will appear.
2. Highlight Create Route and press Delete and Delete All
enter. The Edit Route menu will
Delete is used to remove
appear.
individual trails. Delete
All removes all trails.
3. Highlight Done and press enter.
4. For navigation instructions refer to the
“Navigating a route” segment.
Orientation
Allows you to select North Up or Course Over
Ground (COG) as the map orientation.
Chart Operation | Elite-5m HD
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Overlay Data
Chart Settings
Allows you to select data (course over ground, etc) Controls map data used on the chart screen as well
to be displayed on top of the Chart page.
as display settings like grid lines, waypoints, routes
and trails.
Overlay data
Chart Settings menu
Chart Data
Overlay data setup is covered in the“Pages”section.
Settings
Selects map data that will be used on the Chart
display (Lowrance or Navionics regional map). Go
to Navionics.com to see a full selection of available
charts.
Accesses the “Chart settings”menu.
Chart Operation | Elite-5m HD
22
Download from Www.Somanuals.com. All Manuals Search And Download.
COG Extension
Waypoints, Routes and Trail displays
A line extending from the front
of the current position icon that
estimates the time and distance
to areas in front of you.
From the Chart Settings menu, you can turn on/
off waypoint, route and trail display properties.
Turning off display properties allows you to get
a better view of the map, if the screen becomes
cluttered with waypoints, routes and/or trails.
Grid Lines
Waypoints, Routes, Trails
Displays base values for
latitude and longitude, making
it easier to get a general idea of
your location on the latitude/
longitude scale.
Accesses the Waypoints, Routes & Trails screen.
Waypoints, Routes and Trails are covered in the
“Chart operation”section.
Chart Operation | Elite-5m HD
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrival Radius
navigation Settings
(Advanced mode only)
Sets the arrival radius threshold for the Arrival
Controls Arrival Radius and Off Course distance alarm. The arrival alarm will sound when your ves-
settings and is used to turn on/off WAAS/MSAS/ sel comes within a selected distance (arrival radius)
EGNOS.
of the destination waypoint.
Off Course Distance
Sets Off Course Distance threshold for the Off
Course alarm. When the selected off course dis-
tance is exceeded, the Off Course alarm will sound
when the alarm is enabled.
Bearings
Navigation Settings menu
Controls whether bearing will be calculated using
True North or Magnetic North. Magnetic North
should be used when navigating with a compass
course or heading; otherwise, use the default set-
ting, True North.
Chart Operation | Elite-5m HD
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Magnetic Variation
Controls whether magnetic variation will be calcu-
lated using Automatic or Manual settings. Magnet-
ic variation is the angle between magnetic north
and true north. The automatic setting reconciles
the variation for you.
WARNING: You should only use the
Manual magnetic variation setting if
you have variation information from a
verified source.
Chart Operation | Elite-5m HD
Download from Www.Somanuals.com. All Manuals Search And Download.
25
System
Settings
Adjusts unit settings like language, mute audio
and advanced mode.
Settings menu
Accesses installation and configuration settings for
your unit.
Enables
advanced
features and
settings
(Advanced mode
Settings
menu
System menu
only)
Displays software
information
(Advanced mode only)
Settings | Elite-5m HD
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Language
WAAS/MSAS/EGNOS
Selects the language used on
menus and text boxes.
Turns on/off WAAS, MSAS and EGNOS.
All three systems help increase GPS accuracy for
different parts of the world.
Audio
Time
Adjusts volume and turns on/off unit audio, like
key beeps, alarm sounds, etc.
Used to set local time, and time
and date formats for your unit.
GPS
Monitors the location of satellites
in view and the quality of the
unit’s satellite lock-on. GPS
Source, WAAS/MSAS/EGNOS and
Time features are accessed from
the GPS dialog.
Trip Calculator
Tracks trip time, speed and distance when you are
moving faster than the selected threshold.
Advanced Mode
Enables features and settings
only available with the unit in
Advanced Mode.
GPS Source
Selects the antenna your unit will use for GPS. You
will use the built-in GPS antenna unless you have a
LGC-16W external antenna (p/n: 000-00146-001).
Settings | Elite-5m HD
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Restore Defaults
Lowrance periodically updates unit software to
add features and improve functionality. To see
the latest available software version go to www.
lowrance.com.
Switches the unit back to default settings.
Browse Files
Allows you to view a list of the files saved to the
microSD card.
Alarms
Enables alarms and selects alarm thresholds.
“Arrival,”“Off Course” and “Anchor” alarms are only
available in Advanced mode.
Saving Screenshots
You can save screenshots to a microSD card by
inserting a microSD card into the card slot and
pressing Power and then Zoom (+).
You must view files on a computer or other microSD
compatible device.
Alarms
menu
About
Displays software information about this unit.
Before attempting a software update, you can
check the version of software your unit is using by
accessing the About screen.
Settings | Elite-5m HD
28
Download from Www.Somanuals.com. All Manuals Search And Download.
NMEA 0183 Output
Alarms
You can select the NMEA 0183 sentences the unit
will use when connected to a VHF radio or other
NMEA 0183 device.
sounds alarm when you are within a selected
distance of your destination (Advanced
Mode only)
Arrival
sounds alarm when course exceeds
a
Off
Course
You can also adjust the Baud rate, but the default
setting works best under most conditions.
selected off-course threshold (Advanced
Mode only)
sounds alarm when vessel moves a selected
distance (Advanced Mode only)
Anchor
Units
Allows you to select the unit of measure used by
the unit. Unit options vary depending on whether
the unit is in basic or advanced mode.
Simulator
Simulates GPS activity. Simulations can be
customized on the Simulator options menu.
Basic Mode
Advanced Mode
Settings | Elite-5m HD
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Elite-5m HD
General
GPS
Mapping card slot
GPS Antenna
microSD and microSDHC
5.4”H (136 mm) x 6.9”W (174 mm);
5.9”H (151 mm) with bracket
High accuracy GPS antenna
(internal); optional external GPS
antenna sold separately
Case Size
Display
(5”diagonal) 16-bit color Full
color VGA Solar MAX™ Plus TFT
Mapping
Fishing Hot Spots
&
Navionics
compatibility
(Hotmaps, Premium and Gold)
Waterproof standard IPX7
Up to 3000 waypoints, 100
Waypoints, Routes & routes/100 waypoints per route,
Backlight
LED (11 levels)
Communications
NMEA 0183 Output
Trails
100 retraceable plot trails/up to
10,000 points per trail
Declaration of
Conformity
Part 15.103 FCC rules & CE RTTE
directive 1999/5/EC
Power
Transmit Power
250W RMS; 30,000 PTP
Power
Requirement
12V
Voltage Input
Current drain
Fuse type
10 to 17V
Typical: 1.1A
3-amp Automotive
Specifications | Elite-5m HD
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Dropdown menus 8
Man Overboard way-
point 4
microSD cards 5
Muting Audio 4
A
C
About 28
Add overlay data: 11
Adjusting the backlight Chart Data 22
Cancel navigation 18
Chart 22
E
Editing waypoints 15
4
Chart menu 22
Chart Page 10
COG Extension 23
Creating a route 16
Creating trails 19
Cursor 8
N
G
Advanced Mode 9
Alarms 28
Anchor alarm 29
Arrival alarm 29
Arrival Radius 24
Navigating a route 17
Navigating a trail 21
Navigation 24
Navigation menu 24
New Waypoint 13
NMEA 0183 29
Goto cursor 9
Goto waypoint 15
GPS Source 27
Grid Lines 23
Customizing Overlay
Data 12
B
L
Basic Operation 6
Bearings 24
Browse Files 28
Language 27
O
D
Off Course alarm 29
Off Course Distance 24
M
Data Port 27
Dialogs 8
Magnetic Variation 25
Index | Elite-5m HD
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a GPS Source
4
Setup wizard 6
Software Updates 28
Sort waypoints 16
Standby mode 9
Steer Page 10
On/Off features 7
Orientation 21
Overlay Data 11, 22
Configure 11
Customizing 12
Show 11
W
WAAS/MSAS/EGNOS
27
Waypoint display 23
Waypoints, Routes,
Trails 14
Working with menus 7
System settings 26
P
Page menus 6
T
Text entry 8
Time 27
Trail display 23
Trails Screen 19
Turn unit on/off 4
R
Restore defaults 9
Route display 23
Routes Screen 16
S
U
Saving Screenshots 28
Scrollbars 7
Unit Controls 4
Units 29
Index | Elite-5m HD
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Databases Limited Warranty
Navico Databases License Agreement
“We”, “our”, or “us” refers to Navico, the manufacturer of this product. “You” or “your”
refers to the first person who purchases the product as a consumer item for personal, family, or
household use. The Databases Limited Warranty applies to the one or more databases that your
product may contain. We refer to each of these as a “Database” or together as the “Databases.”
Your product may thus include the “WBS Database” which contains worldwide background
surface mapping data, the “Indigo Database” which contains inland mapping data, or other
Databases.
We warrant to you that we have accurately compiled, processed, and reproduced the portions
of the source material on which the Databases are based. However, we are under no obliga-
tion to provide updates to the Databases, and the data contained in the Databases may be
incomplete when compared to the source material. WE MAKE NO EXPRESS OR IMPLIED
WARRANTY OF ANY KIND ABOUT THE ACCURACY OF THE SOURCE MATERIAL
ITSELF, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES
THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD
USE (“YOU”) AND NAVICO, THE MANUFACTURER OF THIS PRODUCT (“WE”,
“OUR”, OR “US”).
USING THE PRODUCT ACCOMPANIED BY THIS LICENSE AGREEMENT
CONSTITUTES ACCEPTANCE OF THESE TERMS AND CONDITIONS.
IF YOU DO NOT ACCEPT ALL TERMS AND CONDITIONS, PROMPTLY RETURN
THE PRODUCT WITHIN 30 DAYS OF PURCHASE. PLEASE RETURN USING THE
ENCLOSED UPS SHIPPING LABEL AND INCLUDE: PROOF OF PURCHASE, NAME,
ADDRESS, AND PHONE NUMBER. YOUR PURCHASE PRICE AND ANY APPLICABLE
TAXES WILL BE REFUNDED. PLEASE ALLOW 4-6 WEEKS TO PROCESS YOUR
REFUND.
1.
This License Agreement applies to the one or more databases that your product
may contain. We refer to these singly as a “Database” and together as the “Da-
tabases.” Your product may thus include the “WBS Database” which contains
worldwide background surface mapping data, the “Indigo Database” which
contains inland mapping data, or other Databases.
If there is a defect in any Database, your exclusive remedy shall be, at our option, either a
refund of the price you paid for the product containing the defective Database or a replacement
of such product. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANY-
ONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT
DAMAGE OF ANY KIND.
2.
The Databases that your product may contain are licensed, not sold. We grant
to you the nonexclusive, nonassignable right to use these Databases for supple-
mental navigation reference purposes, but only as long as you comply with
the terms and conditions of this License Agreement. We reserve the right to
terminate this license if you violate any aspect of this License Agreement. You
are responsible for using official government charts and prudent navigation for
safe travel.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the product has
been serviced or repaired by anyone other than us; (2) when the product has been connected,
installed, combined, altered, adjusted, or handled in a manner other than according to the
instructions furnished with the product; (3) when any serial number has been effaced, altered,
or removed; or (4) when any defect, problem, loss, or damage has resulted from any accident,
misuse, negligence, or carelessness, or from any failure to provide reasonable and necessary
maintenance in accordance with the instructions of the owner’s manual for the product.
We reserve the right to make changes or improvements in our products from time to time
without incurring the obligation to install such improvements or changes on equipment or
items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights which may
vary from state to state.
Your remedies under this warranty will be available so long as you can show in a reasonable
manner that the defect occurred within one (1) year from the date of your original purchase,
and we must receive your warranty claim no later than 30 days after such 1-year period
expires. Your claim must be substantiated by a dated sales receipt or sales slip.
3.
4.
The Databases housed in your product are protected by the copyright notices
appearing on the product or its screen(s). You may NOT modify, adapt, trans-
late, reverse engineer, decompile, disassemble, rent, lease, or resell any Data-
base, and you may NOT create derivative works based upon any Database or its
contents. Any unauthorized reproduction, use, or transfer of a Database may be
a crime and may subject you to damages and attorney fees.
This License Agreement will terminate immediately without prior notice from
us if you fail to comply with or violate any of the provisions of this Agreement.
Upon termination, you will promptly return all products containing one or more
Databases to us.
5.
6.
Prices and programs are subject to change without notice.
This LicenseAgreement shall be governed by the laws of the State of Oklahoma
and comprises the complete and exclusive understanding between you and us
concerning the above subject matter.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact information
Customer Service:
1-800-628-4487
(8 a.m. to 5 p.m. Central Standard Time, M-F)
(Canada)
1-855-361-1564
(8 a.m. to 5 p.m. Eastern Standard Time, M-F)
Ordering Accessories
Visit our website
Download from Www.Somanuals.com. All Manuals Search And Download.
Visit our website:
*988-10520-001*
N2584
Download from Www.Somanuals.com. All Manuals Search And Download.
|