Linksys Telephone Accessories PAP2 IG v 1 0 042805 User Manual

PAP2 Phone Adapter  
Installation Guide  
OUTBOUND CALLING  
Version 1.0  
DocVersion: PAP2-IG-v1-0-042805  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Linksys PAP2 Installation Guide  
Table of Contents  
1
2
Introduction................................................................ 1  
Adapter Description .................................................... 2  
2.1 PAP2 Overview ..............................................................2  
2.2 Connectors and Pinouts...................................................2  
2.3 Accessing the PAP2 ........................................................2  
3.  
Provisioning ................................................................ 4  
3.1 General Configuration for Outbound Calling........................4  
3.2 Line-Specific Configuration ..............................................5  
Page i  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Linksys PAP2 Installation Guide  
1 Introduction  
This document is an installation/configuration guide for the Linksys PAP2 phone adapter  
running firmware version 2.0.10 (LSc). It describes how to configure the SIP parameters,  
codec settings and analog coefficients for outbound calling. It also includes steps for  
provisioning the device with the user account and PIN. Once you complete these steps,  
you will be ready to begin placing calls.  
Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Linksys PAP2 Installation Guide  
2 Adapter Description  
The sections below briefly describe the PAP2 device.  
2.1 PAP2 Overview  
The PAP2 is a 2-port FXS phone adapter, which allows you to connect two (2) analog  
phones.  
PAP2 2-Port FXS Phone Adapter  
2.2 Connectors and Pinouts  
The image below displays the Ethernet (RJ-45) and analog (RJ-11) line pin-outs.  
Ethernet (RJ-45) and Analog (RJ-11) Line Pin-Outs  
2.3 Accessing the PAP2  
1. Connect an analog phone to the RJ-11 connector on the PAP2.  
2. Using the telephone keypad, press the star key (*) four (4) times: ****.  
You will be prompted to enter a code.  
3. Enter the appropriate code, followed by the pound (#) key. Refer to the PAP2  
Menu Options table on the following page for codes.  
Page 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Linksys PAP2 Installation Guide  
PAP2 MENU OPTIONS  
User Input  
Action  
Code  
Behavior Notes  
Enter IVR Menu  
****  
None  
Do not press any other keys  
until you hear, “Configuration  
menu. Please enter option  
followed by the pound (#)  
key, or hang up to exit.”  
Check DHCP  
Set DHCP  
100  
101  
None  
The system announces if  
DHCP is enabled or disabled.  
Enter 1 to enable.  
Enter 0 to disable.  
Enter the option, followed by  
the pound (#) key.  
Check IP  
address  
110  
111  
None  
Set IP Address  
Enter value using the  
numbers on the  
Enter the value, followed by  
the pound (#) key. DHCP  
must be “Disabled,”  
telephone keypad. Use  
the star (*) key when  
otherwise you will hear the  
entering a decimal point. announcement, “Invalid  
Option” if you try to set this  
value.  
Check Net Mask  
Set Net Mask  
120  
121  
None  
Enter value using the  
numbers on the  
telephone keypad. Use  
Enter the value, followed by  
the pound (#) key. DHCP  
must be “Disabled,”  
the star (*) key when  
otherwise you will hear the  
entering a decimal point. announcement, “Invalid  
Option” if you try to set this  
value.  
Check Gateway  
Set Gateway  
130  
131  
None  
Enter the value using the Enter the value, followed by  
numbers on the  
telephone keypad. Use  
the pound (#) key. DHCP  
must be “Disabled,”  
the star (*) key when  
otherwise you will hear the  
entering a decimal point. announcement, “Invalid  
Option” if you try to set this  
value.  
Check MAC  
Address  
140  
None  
You will hear the phone  
adapter’s MAC address.  
Check Firmware  
Version  
150  
None  
None  
You will hear the phone  
adapter’s firmware version.  
Manual Reboot  
7326668  
After you hear, “Option  
successful,” hang up the  
phone. The phone adapter  
will automatically reboot.  
PAP2 Menu Options  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Linksys PAP2 Installation Guide  
3. Provisioning  
3.1 General Configuration for Outbound Calling  
To configure the PAP2 for outbound calling:  
1. Connect to the PAP2 by entering the device’s IP address in the Web browser’s  
Address bar. For instructions on obtaining the IP address, refer to section 2.3  
Accessing the PAP2 on page 2 in this Guide.  
2. Click on the Admin Login link in the upper right corner of the page, and then  
click the advanced configuration link.  
PAP2 Web Interface – Main Window  
3. Click the System tab, and in the Internet Connection Type section, click the  
DHCP drop-down menu, and select yes or no.  
System Tab  
4. If you set DHCP to no, enter the Static IP, NetMask, and Gateway information.  
If you set DHCP to yes, continue to step 5.  
5. Click the Submit All Changes button at the bottom of the page to save the  
settings.  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Linksys PAP2 Installation Guide  
3.2 Line-Specific Configuration  
1. Click the Line1 or Line2 tab at the top of the page, and in the NAT Settings  
section, change the following setting:  
Field  
Value  
no  
NAT Keep Alive Enable  
2. In the Proxy and Registration section (see the screen on the following page),  
change the following settings:  
Field  
Value  
Proxy  
byod1.net2phone.com  
Use Outbound Proxy  
Use OB Proxy In Dialog  
Make Call Without Reg  
Ans Call Without Reg  
DNS SRV Auto Prefix  
no  
no  
yes  
yes  
no  
3. In the Subscriber Information section (as shown in the Line1/2 Window screen on  
the following page), enter a Display Name. This value can be any alphanumeric  
string. Enter the following values for outbound only service:  
Service Type  
Field  
Display Name  
Value  
Display Name (Line 1)  
Display Name (Line 2)  
NO_DID1  
NO_DID2  
OUTBOUND SERVICE ONLY  
4. Enter the User ID (account) and Password (PIN).  
IMPORTANT You must have a different account and PIN for Line 1 and Line 2.  
5. Click the Use Auth ID drop-down menu, and click no.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Linksys PAP2 Installation Guide  
Proxy and Registration and Subscriber Information Sections  
6. Scroll to the Audio Configuration section (as shown in the Audio Configurations  
and Dial Plan Sections screen on the following page), and change the following  
settings:  
Field  
Value  
Preferred Codec  
Use Pref Codec Only  
G729a Enable  
G729a  
no  
yes  
yes  
no  
G723 Enable  
G726-16 Enable  
G726-24 Enable  
G726-32 Enable  
G726-40 Enable  
DTMF Tx Method  
no  
no  
no  
AVT  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Linksys PAP2 Installation Guide  
Audio Configuration and Dial Plan Sections  
7. In the Dial Plan section, change the Dial Plan to fit the dialing pattern in your  
country. The dialed number must start with ‘1’ for US calls and ‘011’ for non-US  
calls. Please read the PAP2 manual to customize your dial plan.  
8. Click the Submit All Changes button to save the settings.  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lennox International Inc Furnace G40UHX User Manual
Leupold Hunting Equipment Rx 600 User Manual
Linear Telephone AE1000Plus User Manual
LST Smoke Alarm AO 58000 600 User Manual
Lux Products Thermostat ELV4C User Manual
Lux Products Thermostat P711 User Manual
Mackie Music Mixer SW0194 92 User Manual
Magic Chef Blender EWBL20SG User Manual
Master Bilt Home Security System 19 14009 User Manual
Melissa Toaster 743 196 User Manual