AE-2000
Telephone Entry
& Access Control
System
Installation Instructions
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Features
Feature Overview
Relay Outputs
✓ BUILT-IN RADIO RECEIVER
Variable gain, high-sensitivity receiver for wireless transmitters
Four 3-amp dry contact relay outputs are provided to activate access devices,
such as door strikes, magnetic locks, automatic doors, barrier gates, and
automatic sliding gates. The relay outputs can also be used as specialty
outputs for alarm contact shunting, operator obstacle triggering, and alarm
activation. Each of the relays can also be manually activated from buttons on
the AE-2000 circuit board. LED indicators display the status of each relay.
✓ FOUR FORM “C” (N.O. & N.C) RELAYS
Each relay has 3-amp @ 24-volt rating
✓ FOUR REQUEST-TO-EXIT INPUTS
Activates access device for exiting using a hardwired switch
✓ FOUR SENSING INPUTS
For sensing door position to control door-ajar and alarm features
Request-to-Exit Inputs
✓ BUILT-IN ANNUNCIATOR
Each relay channel has a request-to-exit input. These inputs are supplied for
hardwire activation of the access devices. Typically a request-to-exit input is
wired to a pushbutton inside of the access controlled area. When a person
desires to exit, pressing the pushbutton will activate the output relay channel
and trigger the access device. A loop detector for automatic gate operation
can be connected to a request-to-exit input.
Chirps during keystrokes
✓ BUILT-IN MODEM
No add-on modem required for telephone communications with system
✓ RS-232 PORT
COM port for direct connection to a computer
✓ NETWORK SUPPORT
Multiple units can be connected together to share data
Sensing Inputs
The sensing inputs connect to door switches that monitor whether the controlled
door is open or closed.
✓ EXPANSION INTERFACE SUPPORT
Model AM-MIO accessory adds additional input and outputs to the AE-2000
✓ ON-BOARD CLOCK/CALENDAR CIRCUIT
Built-in Modem
Stamps the event log data as it is stored in the system’s memory
A modular connector is provided for telephone line connection to the
unit’s built-in 33.6K baud modem. The system can be accessed remotely
for programming and control over the standard telephone system using a
personal computer with a modem. For system backup, a computer connected
through the modem can store and retrieve the AE-2000’s memory data.
✓ WIEGAND INPUTS
Two Wiegand format card reader inputs for connection to external devices.
✓ LINEAR PBUS SUPPORT
Three PBUS input/output ports for connection of up to 6 Linear accessories.
✓ CCTV COLOR CAMERA SUPPORT
Model CCM-1 accessory camera allows color video monitoring of the keypad area
RS-232 Communications Port
✓ POWER FAILURE MONITOR
A modular connector is provided for the bi-directional 38.4K baud RS-232
port. The AE-2000’s RS-232 port connects to a personal computer’s COM
port. System programming can be performed locally with a computer
connected to the RS-232 port.
AC power input is monitored, power outages are recorded in the event log
Software Highlights
✓ COMPUTER PROGRAMMABLE
No dedicated programmer required, program with a computer and a modem
Local Keypad
The local keypad is the system’s primary keypad. The local keypad activates
Relay Channel “A”, but can be programmed for any of the relays.
✓ LARGE ENTRY CODE CAPACITY
Up to 20,000 entry codes can be used for gaining access
✓ 2-8 DIGIT ENTRY CODE LENGTH
Postal Lock
Flexible code length for different applications
The AE-2000 cabinet has provisions for installing a U.S.P.S. postal lock for
keyed mail carrier access. The postal lock will activate Relay Channel “A”, but
can be programmed for any of the relays.
✓ LARGE RESIDENT DIRECTORY CAPACITY
Up to 10,000 residents
✓ 2-4 DIGIT DIRECTORY NUMBER LENGTH
Directory number lengths can be customized for small or large installations
Obstacle Detection
Linear’s Model MGT safety edge transmitter is compatible with the AE-2000.
The MGT detects and transmits obstacle events to the AE-2000.
✓ LARGE TRANSMITTER CAPACITY
Up to 45,600 block coded and 20,000 individually enrolled Linear transmitters can be used
for gaining access
Programming Memory
The AE-2000’s flash memory retains all entry codes, transmitter information,
card access, and programming, even without power.
✓ TRANSMITTER FACILITY CODE SUPPORT
Identifies wireless transmitters by installation
✓ LARGE CARD CAPACITY
Up to 45,600 block coded and 20,000 individually enrolled cards can be used for gaining
access
Computer Programming
The system programming can be accomplished by a computer and modem
using Linear’s AccessBase2000 programming software.
✓ FOUR INDEPENDENT RELAY CHANNELS
Each output’s action is programmable
Battery Backup
✓ PROGRAMMABLE TIME SCHEDULED RELAY ACTIVATION
The system supports a 12-volt battery backup or uninterruptable power supply
for operation during power outage. The system does not charge the backup
battery, an external battery charger is required to maintain the battery.
Activation for up to four time periods for each of the 31 system time zones
✓ PROGRAMMABLE TIME ZONE ACCESS VALIDATION
Validation during four time periods for each of the 31 system time zones
✓ PROGRAMMABLE VALIDATION DAYS
Network Support
Select days of the week access is allowed
Multiple AE-1000, AE-2000, & AM-3 units can be networked together via
RS-485 allowing information sharing between the units. Networked units are
interconnected with a three-wire cable. A common event log is retained for all
of the networked units.
✓ PROGRAMMABLE HOLIDAY DAYS
Select up to 24 expiring & 24 non-expiring holidays for access restriction
✓ OBSTACLE TRANSMITTER SUPPORT
Compatible with Linear’s Model MGT transmitter
Linear PBUS Ports
✓ EVENT LOG
Three 6-wire Linear PBUS input/output ports are available to connect to
several accessories (keypads, proximity readers, remote receivers). A typical
application for a remote keypad or reader would be to control additional doors
or gates.
Stores up to 20,000 system events in memory for record keeping
✓ DELETED CARDHOLDER DATABASE
System logs deleted cardholders for future identification
✓ TIMED ANTI-PASSBACK
Disables entry code for a programmed time after use
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessory Overview
PBUS Accessories
Several compatible accessories are available to connect to the AE-2000’s
three 6-wire communications “PBUS” inputs. Up to six PBUS accessories
can be used with each AE-2000 unit.
AM-RRR Remote Radio Receiver
For wireless transmitters, connect the Model AM-
RRR high-gain superheterodyne UHF receiver. The
receiver is housed in a weather-resistant enclosure
and can be mounted indoors or outdoors. Gaskets
and a weather-tight wiring strain relief seal the unit
from the elements.
EXA-2000
REMOTE
RADIO
AM-RRR
REMOTE
RADIO
ANTENNA
AM-RRR
AM-RPR Radio Proximity Receiver
RECEIVER
The Model AM-RPR functions as a remote device
that supplies localized radio reception for the
AE-2000 In a typical installation, the AM-RPR
would be mounted in a plastic single-gang electrical
box next to the controlled opening. When the user
requires access, their transmitter must be activated
within three inches of the AM-RPR faceplate.
AE-2000
TELEPHONE ENTRY
& ACCESS CONTROL
SYSTEM
AM-RPR
AM-KP Exterior Keypad
The Model AM-KP is housed in a rugged cast
aluminum enclosure designed for exterior
installations. The die-cast keys have bright,
1
2
5
8
0
3
easy-to-read yellow graphics. The keypad can
be mounted to a pedestal or directly to a wall.
A keylock secures the keypad to the mounting
backplate.
4
7
6
9
#
*
AM-KP
AM-KPI Interior Keypad
The Model AM-KPI keypad is housed in a rugged,
plastic enclosure designed to be mounted indoors
in a standard single-gang electrical box. Tamper
resistant screws secure the keypad to its mounting
plate. The die-cast keys have bright, easy-to-read
yellow graphics and is illuminated with white
LEDs.The keypad is supplied with a satin-chrome
bezel and three interchangeable colored bezels
(white, ivory, & bronze) to customize the keypad
appearance for the installation.
WIEGAND
ACCESSORIES
AM-KPI
PBUS
ACCESSORIES
AM-CRI Card Reader Interface
The Model AM-CRI expands the standard two
AE-2000 Wiegand inputs by supporting one or
two additional 26-bit Wiegand input devices per
AM-CRI interfaces used.
AM-KPI
INTERIOR
KEYPAD
AM-CRI
AM-WOR
WIEGAND
OUTPUT
RECEIVER
Wiegand Accessories
Two Linear accessories are available to connect WIEGAND format
devices to the AE-2000. Most other manufacturer’s 26, 30 & 31-bit
WIEGAND output devices can also be used with the AE-2000.
AM-PR
PROXIMITY
READER
WOR Wiegand Output Radio Receiver
For block-coded Linear wireless transmitters,
connect the Model WOR high-gain superheterodyne
UHF receiver. The receiver is housed in a weather-
resistant enclosure and can be mounted indoors or
outdoors. Gaskets and a weather-tight wiring strain
relief seal the unit from the elements.
*
AM-KP
EXTERIOR
KEYPAD
WOR
AM-PR Proximity Reader
The Model AM-PR is a radio-based reader that
works with either proximity tags (Model AM-PT)
or proximity cards (Model AM-PC), both of which
are slotted to attach to key rings. Upon reading a
user’s tag or card, it transmits the entry data via a
Wiegand output to the AE-2000. An integral LED
AM-RPR
RADIO
PROXIMITY
RECEIVER
AM-CRI
CARD
READER
INTERFACE
confirms to the user that access is granted.
AM-PR
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Locations
DISPLAY
OPTIONAL
CAMERA
MICROPHONE
LEFT
CABINET
LOCK
FUNCTION
BUTTONS
RIGHT
CABINET
LOCK
OPTIONAL
POSTAL
LOCK
SPEAKER
KEYPAD
INSTALLATION NOTE:
FOR EASY WIRING, THE UNIT'S TERMINAL BLOCKS
CAN BE UN-PLUGGED FROM THE CIRCUIT BOARD
PROMPT SPEECH
VOLUME
ADJUSTMENT
ANTENNA
CONNECTOR
TAMPER
SWITCH
CPU/INTERFACE
CONNECTOR
RESIDENT'S VOICE
VOLUME
ADJUSTMENT
TAMPER
SWITCH
CONNECTOR
OPTIONAL
CAMERA
RECEIVER
RANGE KNOB
CAMERA
CONNECTOR
(HIDDEN)
TAMPER
MAGNET
VIDEO
CONNECTOR
WIEGAND
INPUT
TERMINALS
MICROPHONE
SYSTEM
RESTART
BUTTON
PBUS
TERMINALS
RELAY
TERMINALS
NETWORK
TERMINALS
POSTAL LOCK
MOUNTING
PLATE
AM-MIO
INTERFACE
TELEPHONE
INTERFACE
CONNECTOR
POWER
TERMINALS
RS-232
PORT
SPEAKER
TELEPHONE
JACK
EARTH
GROUND
STUD
KEYPAD
POWER
CONNECTOR
PROCESSOR MODULE
POWER CONNECTOR
MAIN POWER
SWITCH
TELEPHONE
TERMINALS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
THIS WIRING EXAMPLE SHOWS:
DOOR ACCESS WITH A DOOR STRIKE ON RELAY CHANNEL "A"
DOOR ACCESS WITH A MAGNETIC LOCK ON RELAY CHANNEL "B"
GATE ACCESS WITH A GATE OPERATOR ON RELAY CHANNEL "C"
(YOUR INSTALLATION MAY VARY)
ELECTRIC
DOOR
STRIKE
DOOR
STRIKE
POWER SUPPLY
AE-2000
DOOR
SENSE
CONTACT
LED2
HOLD
LED1
DAT 1
DAT 0
GND
LED2
HOLD
LED1
DAT 1
DAT 0
GND
READER A
TERMINALS
WIEGAND
DEVICE
DOOR EXIT
REQUEST
BUTTON
N.C.
COM
N.O.
DS-A
GND
RELAY
CHANNEL "A"
TERMINALS
PWR
PWR
LED2
HOLD
LED1
DAT 1
DAT 0
GND
LED2
HOLD
LED1
DAT 1
DAT 0
GND
RTE-A
READER B
TERMINALS
MAGNETIC
DOOR
LOCK
WIEGAND
DEVICE
N.C.
COM
N.O.
RELAY
CHANNEL "B"
TERMINALS
PWR
PWR
DS-B
GND
DOOR
LOCK
POWER SUPPLY
PWR
GND
PWR
GND
RTE-B
RELAY RATING:
3 AMPS @ 30 VOLTS
AC/DC MAXIMUM
PBUS
DEVICE
DAT1
DAT0
DVAL
PCLK
DAT1
DAT0
DVAL
PCLK
PBUS "A"
TERMINALS
DOOR
SENSE
CONTACT
N.C.
COM
N.O.
RELAY
CHANNEL "C"
TERMINALS
DOOR EXIT
REQUEST
BUTTON
PWR
GND
PWR
GND
DS-C
GND
PBUS "B"
TERMINALS
PBUS
DAT1
DAT1
DAT0
DVAL
PCLK
RTE-C
DEVICE DAT0
DVAL
PCLK
N.C.
COM
N.O.
DS-D
GND
GATE
OPERATOR
RELAY
CHANNEL "D"
TERMINALS
PWR
GND
PWR
GND
PBUS
DEVICE
DAT1
DAT0
DVAL
PCLK
DAT1
DAT0
DVAL
PCLK
PBUS "C"
TERMINALS
GATE
EXIT LOOP
SENSOR
RTE-D
NET-B
GND
NET-A
NETWORK
TERMINALS
AE-1000
AE-2000
AM-3
AE-1000
AE-2000
AM-3
AE-1000
AE-2000
AM-3
POWER
TERMINALS
12-24 VOLTS AC/DC
AM-MIO
INTERFACE
RS-232
PORT
DC + DC - AC AC
TELEPHONE
JACK
GROUND
STUD
MULTIPLE NETWORK UNITS
REFER TO NETWORK SECTION
FOR WIRING OPTIONS
TELEPHONE
TERMINALS
EARTH
GROUND
STAKE
EARTH
GROUND
16 VAC
20 VA
TRANSFORMER
TO DEDICATED
TELEPHONE LINE
CONNECT TELEPHONE LINE TO
TERMINALS OR TELEPHONE JACK
12 VOLT
BATTERY
FOR LOCAL COMPUTER CONNECTION
USE LINEAR MODEL A2C
SERIAL COMPUTER CABLE
NOTE: OPTIONAL
BACKUP BATTERY
WILL REQUIRE AN
EXTERNAL CHARGER
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Mounting Requirements
The AE-2000Telephone Entry System can be installed for public or private
use. The mounting requirements will vary depending on the installation.
Review the following information before beginning the installation.
Mounting Environment
Consider the environmental factors at the desired mounting location.
The AE-2000 is designed for direct outdoor installations, however, it is
preferable to protect the unit from extreme exposure to sun, driving rain,
or snow whenever possible. Mounting the unit in a kiosk can provide extra
environmental protection.
Follow Building Codes
Check all local building codes and ordinances prior to installing the
system. Proper installation of the AE-2000 conforming to the local
building codes for access control equipment is a regulatory requirement.
The AE-2000 installation is an extremely important and integral part of
the overall access control system.
Mounting Location
If the AE-2000 is used to control a door or pedestrian gate, locate the unit
as near as practical to the entry point. If the unit is mounted on or in a wall
adjacent to the entry point, be sure the wall is sturdy.The repeated shock
and vibration from a slamming access door or spring-loaded pedestrian
gate must be isolated from the AE-2000. NEVER MOUNT THE UNIT
DIRECTLY TO A MOVING DOOR OR GATE!
!
Gate Installations
If the AE-2000 is used to control a gate operator connected to a vehicular
gate, the unit MUST be mounted AT LEAST 10 feet away from the gate
(open and closed) and gate operator. AT NOTIME SHOULD A PERSON
BE ABLE TO TOUCH THE GATE OR GATE OPERATOR AND THE
AE-2000 AT THE SAME TIME.
10 FEET
MINIMUM
Vehicle Traffic
Do not mount the AE-2000 where it extends into any traffic lane. Locate
the gooseneck pedestal or entry kiosk so all parts of the AE-2000 are
outside the traffic lane. Locate the AE-2000 clear of any turn-around
lanes vehicles use when access is denied.
EDGE OF
TRAFFIC LANE
Americans with Disability Act (A.D.A.) Requirements
THE FOLLOWING WHEELCHAIR ACCESS REQUIREMENTS ARE
FOR PUBLIC DOOR CONTROL INSTALLATIONS ONLY.
1. If the clear floor space allows only forward approach to the system,
the maximum high forward reach allowed is 48” above grade to the
top of the keypad.
2. If the high forward reach to the system is over an obstruction of
greater than 20” but less than 25”, the maximum high forward
reach allowed is 44” above grade to the top of the keypad.
3. If the clear floor space allows parallel approach by a person in a
wheelchair, the maximum high side reach shall be 54” above grade
to the top of the keypad.
4. If the high side reach is over an obstruction of 24” or less, the
maximum high side reach allowed is 46” above grade to the top of
the keypad.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Entry System Mounting
The AE-2000 cabinet is designed to be mounted three ways:
• The unit can be mounted directly to a wall or flat surface.
MOUNTING
PREPARATION
• The unit can be mounted recessed into the wall.
• The unit can be mounted on a standard gooseneck pedestal.
Choose a well lit location near the controlled opening. Wiring access for
power, telephone, earth ground, control output must be available to the
mounting location. If the optional remote accessories are used, wiring
access for these cables must also be available to the mounting location.
2
LOOSEN THE TOP
TWO NUTS & REMOVE
THE BOTTOM TWO NUTS
Opening and Closing the Cabinet
GROUND WIRE STUD
1
CAREFULLY REMOVE THE
The AE-2000’s cabinet hinges are spring loaded to help weather seal
the cabinet. To open the cabinet, press the cabinet door firmly around
each lock while turning each key counterclockwise. To close the cabinet,
press the cabinet door firmly around each lock while turning each key
clockwise.
FIVE WIRING HARNESS
CONNECTORS & GROUND WIRE
Mounting Preparation
Before mounting the system, the main circuit board mounting plate
must be removed to provide access for the wiring hole and mounting
fasteners.
✦ CAUTION!: Touch a grounded object before proceeding to
discharge static electricity from your body.
1. Carefully remove the five main circuit board wiring connectors:
• The CPU/interface ribbon cable connector.
• The processor module power connector.
CAREFULLY REMOVE THE
CIRCUIT BOARD
3
• The telephone interface connector.
• The tamper switch connector.
• The keypad power connector.
2. Remove the nut from the Earth Ground stud and remove the green
ground wire lug from the stud.
3. Remove the two bottom circuit board mounting plate nuts.
4. Loosen the two top circuit board mounting plate nuts.
5. Carefully lift up on the mounting plate, removing the circuit board
mounting plate. Set it aside in a safe place.
Reverse these steps to replace the circuit board mounting plate after the
cabinet mounting is complete.
SURFACE
MOUNTING
Surface Mounting
The cabinet can be mounted on a wall or any suitable flat surface. The
four 3/8” mounting holes or the four self-drill locations can be used to
attach the cabinet to the surface.
1. For wall mounting, hold the cabinet at the approximate mounting
location where the display will be about eye level or slightly above.
2A. If using the 3/8” mounting holes, mark the four mounting hole
centers. Drill as required. Use the appropriate fasteners for the
mounting surface to secure the cabinet.
OR
MARK THE FOUR
MOUNTING HOLES
1
2B. If using the self-drill mounting holes, choose the correct size bit for
the fasteners and drill the cabinet as required. Use the appropriate
fasteners for the mounting surface to secure the cabinet.
3. After routing the wiring into the cabinet, replace the circuit board
mounting plate and plug in the wiring connectors. Be sure to
replace the green ground wire.
DRILL THE CABINET AT THE
PRE-MARKED LOCATIONS
ATTACH THE CABINET WITH APPROPRIATE
HARDWARE FOR THE MOUNTING SURFACE
2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Entry System Mounting (Continued)
Recessed Mounting
The cabinet can be mounted recessed using the accessory trim-ring
(P/N ACP00914). The trim-ring mounts in the wall and the cabinet
attaches to the trim-ring.
DETERMINE LOCATION FOR
THE 15-½" x 19" MOUNTING HOLE
MARK HOLE LOCATION
1
2
RECESSED
MOUNTING
1. Identify the location of any studs in the wall.
2. Cut a 15-½” wide by 19” high rectangular hole between studs at
the mounting location.
19"
3. Install any additional mounting material required to provide
surfaces inside the wall 15-½” apart for attaching the trim-ring.
4. Place the trim-ring in the wall hole. Check for level, then attach the
trim-ring with up to six screws into the side tabs.
15-½"
5. Drill the cabinet’s six self-drill mounting holes the appropriate size
for the hardware.
CUT MOUNTING HOLE
INSTALL ANY SHIMS TO
4
3
6. Attach the cabinet to the trim-ring using self-tapping screws.
7. After routing the wiring into the cabinet, replace the circuit board
mounting plate and plug in the wiring connectors. Be sure to
replace the green ground wire.
ALLOW MOUNTING AND
ATTACH THE TRIM-RING
WITH UP TO 6 SCREWS
DRILL 3/16" HOLES IN
THE CABINET AT THE
PRE-MARKED LOCATIONS
5
ATTACH THE CABINET TO
THE TRIM-RING WITH
SELF-TAPING SCREWS
6
Pedestal Mounting
ALIGN THE REINFORCING PLATE
ON THE INSIDE OF THE CABINET
The cabinet can be mounted on a gooseneck pedestal. Linear
manufacturers two pedestals: Model GNC-1 is for surface mounting with
concrete fasteners, Model GNB-1 is for burial mounting. When mounting
to a pedestal, use the cabinet reinforcing plate to stiffen the cabinet.
1. Install the pedestal at the desired location.
PEDESTAL
MOUNTING
2. Place the reinforcing plate inside the cabinet.
3. Use security hardware to attach the cabinet and reinforcing plate
to the pedestal.
4. After routing the wiring into the cabinet, replace the circuit board
mounting plate and plug in the wiring connectors. Be sure to
replace the green ground wire
PEDESTAL
USE SECURITY HARDWARE
TO ATTACH THE PLATE AND
CABINET TO THE PEDESTAL
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Relay Output Wiring
Any of the four relay outputs channels (A-D) can be used to control
access devices on doors or gates.
TYPICAL DOOR STRIKE HOOKUP
ELECTRIC
DOOR
RELAY
TERMINALS
N.C.
Door or Pedestrian Gate Control
1. Install a low voltage electric door strike or magnetic lock as a
locking device for the door or pedestrian gate.
2. Install the power supply or transformer for the locking device. DO
NOT POWER THE AE-2000 FROM THIS POWER SUPPLY.
3. Connect one wire from the power supply to one wire from the
locking device.
4. Route two wires between the locking device and the AE-2000.
Connect one wire to the remaining wire of the locking device.
Connect the other wire to the remaining wire of the power supply.
5A. For a door strike, connect the wires to the AE-2000 relay COM &
N.O. terminals.
COM
N.O.
DS
STRIKE
DOOR
STRIKE
POWER SUPPLY
GND
RTE
TYPICAL MAGNETIC LOCK HOOKUP
MAGNETIC
DOOR
LOCK
N.C.
COM
N.O.
DS
5B. For a magnetic lock, connect the wires to the AE-2000 relay COM
& N.C. terminals.
DOOR
LOCK
POWER SUPPLY
GND
RTE
Gate Control
1. Route two wires between the gate and the AE-2000.
2. Connect the gate operator’s OPEN terminals to the AE-2000 relay
COM & N.O. terminals.
✦ NOTE: For operator wiring specifics, refer to the gate operator’s
wiring diagram.
TYPICAL AUTOMATIC GATE HOOKUP
N.C.
COM
N.O.
DS
GATE
OPERATOR
Request-to-Exit Inputs
Each of the four relay outputs has a request-to-exit input terminal.
Grounding this terminal will activate the associated relay. Exit request
inputs are typically used with push bars, loop sensors, or pushbuttons.
1. Install the pushbutton or device to signal an exit request.
2. Route two wires from the device to the AE-2000.
3. Connect the device’s normally open output to the wires.
4. To activate a relay channel, connect the wires to the associated
relay request-to-exit terminal (RTE-A, RTE-B, RTE-C, or RTE-D)
and GND terminals.
GND
RTE
RELAY RATING:
3 AMPS @ 30 VOLTS
AC/DC MAXIMUM
NOTE: DOOR
SENSE CONTACT
IS NORMALLY CLOSED
Sensing Inputs
The sensing inputs can connect to a door switch that monitors whether
the controlled door is open or closed.
DOOR
SENSE
CONTACT
1. To use the door sense feature to detect forced entry or door ajar
conditions, install a normally closed door switch on the door
or pedestrian gate and route two wires from the switch to the
AE-2000.
N.C.
COM
N.O.
DS
2. Connect the sensing device wires to the associated relay sensing
terminal (DS-A, DS-B, DS-C, or DS-D) and GND terminals.
GND
RTE
DOOR EXIT
REQUEST
BUTTON
RELAY
TERMINALS
DS = SENSING INPUT
OR
RTE = REQUEST-TO-EXIT
GATE
EXIT LOOP
SENSOR
NOTE: DOOR EXIT REQUEST BUTTON
AND GATE EXIT LOOP CONTACT
ARE NORMALLY OPEN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Power, Battery, & Ground Wiring
Power Wiring
✦ NOTE: DO NOT APPLY POWER UNTILTHE INSTALLATION IS
COMPLETE.TURN MASTER POWER SWITCH OFF BEFORE
WIRING.
POWER
TERMINALS
1. Route two wires between the AE-2000 and the power transformer.
• For power wire runs up to 75 feet, use 18 AWG, THHN 600-volt
insulated wire.
EARTH
GROUND
STUD
• For power wire runs up to 150 feet, use 16 AWG, THHN 600-volt
insulated wire.
2. Connect the wires to the transformer. Connect the other end of the
wires to the AE-2000 AC1 & AC2 terminals.
Backup Battery / Uninterruptable Power Supply
Use of battery backup is optional. It will allow the AE-2000 to operate for
short periods of time without AC power. The door or gate access device
must use some type of battery backup of its own for the entire system to
be functional.
EARTH
GROUND
STAKE
12 VOLT
BATTERY
A backup battery will not fit into the AE-2000 case. Protect the backup
battery inside a rain-tight NEMA enclosure suitable for the installation.
✦ NOTE: A backup battery is not required to maintain the AE-2000
clock/calendar and programming memory during power outages.
1. Route two wires between the AE-2000 and the backup battery.
2. Connect the Battery positive to the AE-2000 DC+ terminal and the
negative to the DC- terminal.
NOTE: THE OPTIONAL
BACKUP BATTERY
WILL REQUIRE AN
EXTERNAL CHARGER
16 VAC
50 VA
TRANSFORMER
✦ NOTE: The AE-2000 does not supply battery charging current.
An external battery charger will be required to maintain the battery.
Earth Ground
For the best ground, use size 12 gauge solid wire or larger to connect to
an 8-foot copper ground rod. Locate the ground rod next to the Power and
Telephone company rods and bond the rods together with a new clamp.
Do not disturb the clamps installed by the Power or Telephone Company.
Alternately, connect to a metallic cold water pipe for the earth ground.
1. Connect the wire from the earth ground to the AE-2000’s EARTH
GROUND STUD.
RS-232 Port
A modular connector is provided for the bi-directional 38.4K baud RS-232
port.The AE-2000’s RS-232 port connects to a personal computer’s COM
port. System programming can be performed locally with a computer
connected to the RS-232 port using the AccessBase 2000 software.
AE-2000
RS-232 PORT
COMPUTER'S
COM PORT
SET COMPUTER COM PORT
BAUD RATE TO 38,400 BPS
LINEAR MODEL A2C
SERIAL COMPUTER CABLE
NOTE: USE A DB-25 TO DB-9 CABLE ADAPTER IF REQUIRED
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Wiring
For telephone entry and programming, the AE-2000 connects to a
standard telephone line.
TELEPHONE
TERMINALS
TELEPHONE
JACK
Important Telephone Wiring Tips
• DO NOT ROUTE TELEPHONE AND AC WIRING INSIDE THE
SAME CONDUIT. Route all telephone wires inside a dedicated
conduit that is at least six inches away from any AC line wiring.
• All telephone wiring must be made on the “building” side of the
telephone company’s demarcation device (the terminal block
where the telephone line connects to the building).
• If any security system or personal alert system at the installation is
connected to the telephone line, be sure that it is connected to the
line ahead of the AE-2000 using a RJ-31X or RJ-38X interface.
• Use only high-quality telephone wire. All telephone wire should be
twisted-pair with a minimum size of 24 AWG.
CONNECT TELEPHONE
LINE TO TERMINALS OR
TELEPHONE JACK
TO THE INCOMING
DEDICATED TELEPHONE LINE
Typical Telephone Wiring
1A. If using the AE-2000 modular connector for the telephone
connection, connect a double-ended modular cable between the
AE-2000’s PHONE jack and the modular telephone jack wired to
the installation’s telephone line.
NOTE: THE EARTH
TERMINAL CAN BE
USED TO CONNECT
TO THE TELEPHONE
GROUND
1B. If using the AE-2000 terminal block for the telephone connection,
connect the “ring” wire (usually red) to the RING terminal, connect
the “tip” wire (usually green) to the TIP terminal.
Optional Radio Antenna
If wireless transmitters are going to be used in the system a remote
antenna must be installed to provide reception for the AE-2000.
A basic antenna kit is supplied with the AE-2000. The kit contains a
whip antenna, connector, and a 36” length of coax cable. The antenna
connector should be mounted on a metal surface using a 3/8” hole.
Two other models of antennas are compatible with the AE-2000. The
Model EXA-1000 is a non-directional antenna. The Model EXA-2000 is
a directional antenna used in installations where transmitted signals are
desired to be received only in a particular direction.
OPTIONAL EXA-1000
OMNI-DIRECTIONAL
ANTENNA
36" COAX
WHIP
ANTENNA
SUPPLIED
ANTENNA
KIT
CONNECTOR
✦ NOTE: Up to 50 feet of type RG-59 coax can be used to connect
the antenna to the AE-2000. Keep the coax as short as possible.
1. Install the antenna. (See installation instructions if using the
EXA-1000 or EXA-2000.)
OPTIONAL
EXA-2000
DIRECTIONAL
ANTENNA
2. Connect the antenna coax cable to the antenna and route the
cable to the AE-2000.
3. Connect the cable to the AE-2000’s ANTENNA connector.
RECEIVER
RANGE
KNOB
Receiver Range Control
The AE-2000 has a RECEIVER RANGE adjustment knob. In some
installations, it may be necessary to reduce the effective radio range of
the receiver to limit the distance that transmitters can be used. Reducing
the radio’s sensitivity may also help in installations where unwanted
interference is overpowering signals from transmitters.
AE-2000
CIRCUIT BOARD
1. After the installation and system programming is complete,
adjust the RECEIVER RANGE knob to suit the installation. Test
transmitters from typical locations that they will be used. Set the
radio range so the receiver can activate from transmitters from
about 25% more distance than required.
RECEIVER
TEST POINT
CONNECT COAX
TO ANTENNA
CONNECTOR
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Postal Lock
A postal lock can be installed in the AE-2000 Entry System to provide
keyed access for the postal service. The AE-2000 case is designed to
accept a U.S.Postal Service postal lock.When the postal lock is engaged,
the programmed output relay will activate.
1
REMOVE LOCKNUTS
2
REMOVE PLATE
Postal Lock Installation
1. After opening the cabinet, re-lock the left cabinet lock to provide
clearance to remove the postal lock switch plate.
2. Remove the four locknuts that retain the postal lock switch plate,
hole cover plate, and block (below the left cabinet lock on the
AE-2000 faceplate). The hole cover plate and block will not be
used and can be discarded.
REPLACE PLATE WITH THE
MICROSWITCH TOWARDS
THE FRONT OF THE CABINET,
REPLACE LOCKNUTS
4
INSTALL POSTAL LOCK
3
3. Remove the switch plate from the four studs.
4. Install the postal lock assembly onto the four studs. The postal
lock’s moving plunger should point down (see figure).
5. Replace the postal lock switch plate with the microswitch oriented
toward the front of the cabinet where it will be pressed by the
postal lock’s moving plunger (see figure).
6. Secure the postal lock and switch plate with the four locknuts.
✦ NOTE: Be sure the postal lock’s plunger actuates the
microswitch. Adjust the switch plate and the postal lock then test
the action until the microswitch fully actuates.
PLUNGER
POINTS
DOWN
7. Tighten the four locknuts after the adjustment and testing is
complete.
NOTE: BE SURE THE POSTAL LOCK'S PLUNGER ACTUATES THE
MICROSWITCH. ADJUST THE SWITCH PLATE AND THE POSTAL LOCK
THEN TEST THE ACTION UNTIL THE MICROSWITCH FULLY ACTUATES
8. When programming the system, set the postal lock option to
activate the desired relay output.
Optional Color CCTV Camera
inside the AE-2000 Entry System.The camera provides a video signal for
viewing the area in front of the entry system.
Linear’s Model CCM-1 (P/N ACP00904) CCTV camera can be installed
1
2
REMOVE THE COVER PLATE
REMOVE PLATE RETAINING NUTS
The CAMERA connector is used to connect the camera to the AE-2000.
The 4-conductor cable routes power to, and video from the camera.
The VIDEO jack is the camera output for connection to a video cable with
a Type “BNC” connector. Up to 400 feet of 75-ohm RG-59 video cable can
be used. Longer cable runs may require the use of a video amplifier.
Camera Installation
1. Remove the two plate locknuts from the camera mounting studs
above the right keylock on the AE-2000 faceplate.
2. Remove the cover plate.
3. Remove the protective backing from the plastic window included
with the camera and install the plastic window onto the studs with
the adhesive side against the door.
3
4
INSTALL THE CLEAR WINDOW
REMOVE THE LENS CAP
REMOVE PROTECTIVE
BACKING AND APPLY
WINDOW WITH
ADHESIVE SIDE
AGAINST DOOR
4. Remove the lens cap from the camera.
5. Mount the camera assembly on the two studs, with the alignment
hole in the camera bracket towards the top. Secure the camera
with the two locknuts.
6
5
ATTACH CAMERA WITH TWO NUTS
CONNECT
CAMERA
WIRING
HARNESS
6. Connect the camera’s cable to the AE-2000’s CAMERA connector.
7. Connect the video cable to the AE-2000’s VIDEO connector.
8. Connect the other end of the video cable to the viewing monitor or
the video distribution system.
7
CONNECT
VIDEO
CABLE
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PBUS Accessories
Six accessories (keypads, proximity readers, remote receivers) can be
connected to the AE-2000’s three PBUS input/output ports. A typical
application for a remote keypad would be to control a second door or
gate.
NOTE: UP TO SIX PBUS
DEVICES MAY BE CONNECTED
TO THE THREE SETS OF AE-2000
PBUS TERMINALS
PBUS
TERMINALS
Linear’s PBUS devices compatible with the AE-2000 are:
• AM-RRR Remote Radio Receiver
• AM-RPR Radio Proximity Receiver
PWR
GND
PWR
GND
REMOTE
DAT1
DAT1
DAT0
DVAL
PCLK
• AM-KP Exterior Keypad
• AM-KPI Interior Keypad
• AM-CRI Card Reader Interface
PBUS
DAT0
DEVICE
DVAL
PCLK
1. Mount and install the accessory as described in its installation
instructions.
2. Route 6-conductor cable from the AE-2000 to the accessory.
SET THE REMOTE
DEVICE ADDRESS
SWITCH TO A UNIQUE
DEVICE ADDRESS
•
For wire runs up to 300 feet use 24 AWG Belden Type 9931 or
equivalent.
•
For wire runs up to 600 feet use 20 AWG Weico Type 9405 or
equivalent.
3. Set the DEVICE ADDRESS rotary switch in the accessory to
a unique address number. When programming the system, the
device address number will identify each PBUS accessory to the
AE-2000.
4. Connect the 6-conductor cable to the accessory and the AE-2000.
Wiegand Accessories
The two AE-2000 Wiegand inputs (WIEGAND A & B) can connect to
a large variety of 26, 30, and 31-bit Wiegand output accessories. The
Wiegand format is a common standard for access control equipment.
A typical application would be to add swipe card or proximity readers to
the system.
WIEGAND
TERMINALS
✦ NOTE: Depending on the Wiegand accessory used, the LED1,
LED2, and HOLD connections may not be required.
•
•
LED1 output is switched to ground during non-access time.
LED2 output is switched to ground for one second during access
time.
LED2
HOLD
LED1
DAT1
DAT0
GND
LED2
HOLD
LED1
DAT1
REMOTE
WIEGAND
1. Mount and install the Wiegand accessory as described in its
installation instructions.
2. Route a cable from the AE-2000 to the accessory.
DEVICE DAT0
GND
•
•
For wire runs up to 300 feet use 24 AWG Belden Type 9931 or
equivalent.
PWR
PWR
For wire runs up to 500 feet use 20 AWG Weico Type 9405 or
equivalent.
3. Connect the cable to the accessory and the AE-2000 as shown in
the figure.
NOTE: THE LED1, LED2, AND HOLD
CONNECTIONS MAY NOT BE REQUIRED
DEPENDING ON THE WIEGAND DEVICE USED
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Network Connection
Linear’s AE-1000, AE-2000, & AM-3 Access Control Systems can
be connected together in a network. A network will allow sharing
programming and user information between the systems.
Network wiring conforms to 3-wire RS-485 electrical specifications. Units
connected in the network can be wired using one unit as a “hub” or by
wiring from one unit to the next in “daisy-chain” fashion. See the figures
for wiring options.
ACCESS CONTROL HOMERUN NETWORK
USING ONE UNIT AS A NETWORK MASTER
NETWORK
UNIT "2"
SHIELD
NET-B
GND
NET-A
• Use Belden 9925 or Carol C0600 shielded cable or equivalent.
Maximum wire run distance is 4000 feet.
✦ NOTE: Be sure to connect the cable’s shield to one of the GND
terminals.
NETWORK
MASTER
UNIT "1"
NETWORK
UNIT "3"
Network with Hub
1. Mount and install the units for the network.
2. Choose one unit to be the Network Hub. Usually this would be a
centrally located or “main” unit.
3. Route 3-conductor shielded cable from the hub unit to one of the
other units. Repeat this step to connect the hub unit to each of the
other units.
SHIELD
NET-B
GND
NET-A
NET-B
GND
NET-A
NOTE: GROUND
CABLE SHIELDS
ONLY AT ONE END
4. Connect the 3-conductor cable to each unit’s NETWORK
terminals.
NETWORK
UNIT "4"
Network Daisy-chain
SHIELD
1. Mount and install the units for the network.
2. Route 3-conductor shielded cable from one unit to the next unit
until there is cabling run to all of the units.
3. Connect the 3-conductor cable to each unit’s NETWORK
terminals.
NET-B
GND
NET-A
NETWORK
MASTER
UNIT "1"
NETWORK
UNIT "2"
SHIELD
NET-B
GND
NET-A
NET-B
GND
NET-A
NETWORK
UNIT "3"
ACCESS CONTROL
NETWORK USING
"DAISY CHAIN"
WIRING
NET-B
GND
NET-A
NETWORK
UNIT "4"
NET-B
GND
NET-A
NOTE: GROUND
CABLE SHIELDS
ONLY AT ONE END
15
Download from Www.Somanuals.com. All Manuals Search And Download.
System Adjustments
The factory settings are sufficient for most installations. The system can
be adjusted to customize the installation.
SYSTEM
VOLUME
ADJUSTMENT
System Volume Adjustment
The sound level of the synthesized voice and key beep can be adjusted.
1. Locate the SYSTEM VOLUME adjustment on the CPU circuit board.
2. Press keys on the keypad while adjusting the control until the
sound is at the desired level. Turn the adjustment clockwise for
more volume, counterclockwise for less volume.
LESS MORE
2-Way Audio Volume Adjustment
If the resident’s voice from the speaker is too loud or not loud enough,
the speaker’s volume can be adjusted.
1. Locate the 2-WAY AUDIO VOLUME adjustment on the CPU circuit
board.
AE-2000
CPU CIRCUIT BOARD
2. Make a directory number call to test the speaker volume. While
listening to the resident’s voice, turn the adjustment clockwise for
more volume, counterclockwise for less volume.
System Restart Button
Pressing the SYSTEM RESTART button will reboot the system’s
microcontroller. NO SYSTEM INFORMATION WILL BE ERASED.
Display Contrast Adjustment
If the lighting in the area or the viewing angle of the display in the
installation causes the display to look too dark or too light, the display’s
contrast can be adjusted.
SYSTEM
RESTART
BUTTON
2-WAY AUDIO
VOLUME
ADJUSTMENT
LESS MORE
1. Press the 1, 5 & 9 keys at the same time. The system will assume
Contrast Adjustment Mode for 15 seconds.
2. Press the up and down arrow keys until display has the best
visibility.
3. Press the
or
key to exit Contrast Adjustment Mode.
System Diagnostics
HOST
ON-LINE
Several components on the main circuit board are for monitoring the
system during operation. When calling for technical assistance, Linear’s
Technical Services Department may ask the installer to use these
components to diagnose the system.
STATUS/PROGRAM
DISPLAY
ACCESS
GRANTED
VALIDATE
DECODE
RADIO
On-board Indicators
17 LED indicators are on the main circuit board. Refer to the figure for the
location of each indicator.
RELAY "A"
ACTIVE
•
•
•
STATUS/PROGRAM DISPLAY shows supervisory and status conditions,
also used for some local programming.
ACCESS GRANTED lights when a credential is validated and access is
granted.
HOST ON-LINE lights when the Host PC is connected to the Master
Node.
READER "A"
RELAY "B"
ACTIVE
READER "B"
AE-2000 MAIN
CIRCUIT BOARD
PBUS
•
•
•
•
•
•
•
•
•
VALIDATE lights when a credential is determined to be valid.
DECODE lights when a credential has been successfully decoded.
RADIO flashes when data or interference is received by the built-in radio.
RELAY “A” ACTIVE lights when the Channel “A” relay is energized.
RELAY “B” ACTIVE lights when the Channel “B” relay is energized.
RELAY “C” ACTIVE lights when the Channel “C” relay is energized.
RELAY “D” ACTIVE lights when the Channel “D” relay is energized.
POWER lights when AC or DC power is present.
RELAY "C"
ACTIVE
RELAY "D"
ACTIVE
NETWORK
OFF-HOOK lights when the system has the incoming telephone line
seized.
•
•
•
•
•
TALK lights when the system is communicating over the telephone line.
NETWORK flashes in response to network traffic.
PBUS blinks when any PBUS device is successively decoded.
READER “B” flashes when Wiegand B device is successfully decoded.
READER “A” flashes when Wiegand A device is successfully decoded.
TALK
OFF HOOK
POWER
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Internal Controls
Seven pushbuttons are on the main circuit board. Refer to the figure for
the location of each pushbutton.
On-board Pushbuttons
STATUS/PROGRAM
DISPLAY
"UP"
BUTTON
"DOWN"
BUTTON
•
•
“UP” BUTTON adds one to the value on the STATUS/PROGRAM display.
“DOWN” BUTTON subtracts one from value on the STATUS/PROGRAM
"ENTER"
BUTTON
display.
•
•
•
•
•
RELAY “A” LATCH press to latch relay “A”, press again to un-latch.
RELAY “B” LATCH press to latch relay “B”, press again to un-latch.
RELAY “C” LATCH press to latch relay “C”, press again to un-latch.
RELAY “D” LATCH press to latch relay “D”, press again to un-latch.
RELAY "A"
LATCH
RELAY "B"
LATCH
AE-2000 MAIN
CIRCUIT BOARD
ENTER BUTTON press to accept the value on the STATUS/PROGRAM
display during programming, press to clear an indication during the
supervisory display.
RELAY "C"
LATCH
On-board Display
The STATUS/PROGRAM display will show system conditions and can be
used to aid system setup.
Status Mode
RELAY "D"
LATCH
While the system is running, the display will show the current system
status. Normally the left digit will show a moving pattern and the right digit
will show the unit’s Network Node number.
When a supervisory condition exists, the display will cycle to show the
condition(s).When an item is displayed, press the ENTER button to clear
the display (clears the display only, the condition may still exist). Refer to
the following table for the supervisory condition display codes.
SYSTEM IDLE
STATUS/PROGRAM
DISPLAY
STATUS MODE DISPLAY
DISPLAY
CONDITION
MGT TRANSMITTER STATUS EXCEPTION
MGT TRANSMITTER LOW BATTERY
MGT TRANSMITTER TAMPER
RIGHT DIGIT SHOWS NETWORK NODE ADDRESS
LEFT DIGIT CIRCULATES
01
02
03
04
05
06
07
08
STATUS MODE
AC POWER FAIL (BACKUP BATTERY REQUIRED)
CHANNEL “A” LOCKED CLOSED
CHANNEL “B” LOCKED CLOSED
CHANNEL “C” LOCKED CLOSED
CHANNEL “D” LOCKED CLOSED
DIGITS SHOW SUPERVISORY CODE
PROGRAM MODE
DISPLAY ALTERNATES
Program Mode
RIGHT DIGIT BLANK
DIGITS SHOW THE OPTION VALUE
Options for up to ten system settings can be controlled in Program Mode.
By viewing the STATUS/PROGRAM display and using the UP, DOWN,
and ENTER pushbuttons, the various options can be set for each of the
system settings.
LEFT DIGIT SHOWS THE SYSTEM SETTING NUMBER
PROGRAM MODE DISPLAY
SYSTEM SETTING NUMBER
VALID OPTION VALUES
NETWORK NODE ADDRESS 01-08
Refer to the following steps to change the system settings:
1. To enter Program Mode, press and hold the UP and DOWN
pushbuttons for one second.
0
✦ NOTE: A unique network address (1-8) must be set before
communicating with network.The master node must be set to 1
(default).
2. The display will alternate between the system setting number and
the option value currently set for it. When showing the system
setting number, the left digit of the display will show the system
setting number (0-9) and the right digit of the display will be blank.
When showing the option value both display digits are used to
show the 2-digit option value.
5. Press the ENTER button while the option value is displayed to
program the value into memory.
6. Press the SYSTEM RESTART button on the CPU Circuit Board.
✦ NOTE: The unit takes up to 30 seconds to reset after pressing
the SYSTEM RESTART button.
3. Press the ENTER button while the system setting number is
displayed to advance the system setting number.
4. Press the UP or DOWN button while the option value is displayed
to change the option value.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Visitor Access with a Resident Call
AE-2000 Operation
PRESS THE
TO SCROLL THROUGH THE RESIDENT'S NAMES
KEY BELOW THE
OR
REPEATEDLY
Resident Access with an Entry Code
- OR -
KEY IN AN ENTRY CODE AT THE SYSTEM KEYPAD
OR ENTER A CODE AT A REMOTE KEYPAD
TO SCROLL THROUGH FASTER, PRESS AND HOLD
THE
THE KEY WHEN THE DESIRED LETTER IS UNDERLINED
KEY BELOW
OR
THEN RELEASE
IF THE CODE IS ENTERED WRONG, PRESS THE
KEY TO RESET THE KEYPAD AND RE-ENTER
THE CORRECT CODE (USE THE
REMOTE KEYPADS)
KEY TO RESET
WITH THE RESIDENT DIRECTORY DISPLAYED,
ENTER THE RESIDENT'S DIRECTORY NUMBER TO
PLACE A TELEPHONE CALL TO THE RESIDENT
- OR -
IF THE SYSTEM IS DISPLAYING THE DIRECTORY NAMES,
KEY FIRST, BEFORE KEYING IN AN
PRESS THE
ENTRY CODE
IF THE VISITOR ALREADY KNOWS THE RESIDENT'S
DIRECTORY NUMBER, THEY CAN PRESS THE
THEN ENTER THE DIRECTORY NUMBER WITHOUT
VIEWING THE DIRECTORY DISPLAY
KEY
PRESSING THE KEY DURING A TELEPHONE CALL
WILL CANCEL THE CALL IN PROGRESS
• Residents have up to 40 seconds to key in their entry code.
• Up to eight seconds are allowed between each keystroke.
VISITOR
• If the code is entered wrong, press the
keypad and re-enter the correct entry code. (On remote keypads,
press the key to reset the keypad.)
key to reset the
RESIDENT
THE RESIDENT TALKS TO THE VISITOR
AND CAN GRANT OR DENY ACCESS
USING THEIR TELEPHONE KEYS
RELAY "A"
• If the system is displaying the directory names, press the
first, before keying in the entry code.
key
RELAY "B"
DISCONNECT
• After a correct code is entered, and if the conditions for granting
access are fulfilled, the programmed relay will activate for the
programmed time.
• Press the
scroll through the resident’s names alphabetically and display their
key below the
or
arrow repeatedly to
associated directory number.
• If the number of incorrect codes entered exceeds the keypad
lockout count, the keypad will be locked and not accept any entries
for one minute.
• To scroll through the alphabet faster and choose which letter to
view, press and hold down the
arrow. Release the key when the desired letter is underlined.
key below the
or
• If the Anti-passback feature is enabled, the entry code will be
unusable until the anti-passback time expires.
• With the resident directory displayed, the visitor enters the
directory number to place a call to the resident.
Resident Access with a Wireless Transmitter
• If the visitor already knows the resident’s directory number, they
can press the
viewing the directory display.
key then enter the directory number without
ACTIVATE TRANSMITTER
ANTENNA
• The system will dial the resident’s telephone number to establish
2-way communications.
✦ NOTE: The resident’s telephone number will never be displayed to
the visitor.
• If the resident is using the telephone at the same time a visitor
calls, the system will indicate to the visitor that the line is busy.
• The resident answers the call and converses with the visitor to
determine if access will be granted.
• Activate a wireless transmitter within radio range of the AE-2000’s
antenna.
• The resident can use their telephone’s keypad to grant access
• After a valid transmitter is decoded, and if the conditions for
granting access are fulfilled, the programmed relay channel will
activate for the programmed time.
activating Relay Channel “A” by pressing
or activating Relay
,
Channel “B” by pressing . After access is granted, the system
will disconnect the visitor and resident call.
• If the Anti-passback feature is enabled, the transmitter will become
unusable until the anti-passback time expires.
• The resident can disconnect the visitor without granting access by
pressing
or by hanging up.
✦ NOTE: The telephone keys that the resident presses can be
customized for the installation.
• The length of time the visitor is allowed to talk can be programmed
from 15-255 seconds. The resident will hear a series of beeps
during the last 10 seconds of talk time. To restart the talk timer, the
resident can press
on their telephone.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
MECHANICAL
Case dimensions: 15-1/4” W x 19” H x 4” D
ELECTRICAL
Voltage: 16-24 Volts AC or 12-24 Volts DC
Current: 2000 mA @ 16 VAC maximum
Backup Battery: Externally charged 12 Volt DC source, 6 amp/hr minimum
Outputs: Relay Channels A-D
Form “C” 3 Amps @ 30 Volts maximum
Inputs: Four normally closed door sense inputs
Four normally open exit request inputs
Two WIEGAND reader inputs
Three PBUS inputs
Network: Three-wire network
RADIO
Frequency: 318 MHz 500 KHz @ 23°C
Bandwidth: 300 KHz Typical
Sensitivity: -97 dBm Minimum (-100 dBm Typical)
®
Encoding: Linear MegaCode Format
ENVIRONMENTAL
Temperature: -22°F to 149°F (-30°C to 65°C)
Humidity: 5% to 95% non-condensing
Dimension Drawing
AE-2000
OPTIONAL TRIM RING
21-1/8"
19"
17-3/8"
4"
15-1/4"
4"
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Main or remote keypad will not activate a relay
1. Entry code is not assigned.
2. Keypad may be in lockout from too many incorrect attempts. Wait
one minute for lockout to clear and try again.
3. Remote keypad wiring incorrect.
Troubleshooting
1. No power from transformer. Check voltage at transformer terminals.
2. Check voltage at AE-2000 power terminal strip.
System completely dead
Resident’s Telephone does not ring when a visitor calls
1. Resident’s telephone number programmed incorrectly.
2. Check AE-2000 telephone line.
3. Call resident from another line or cell phone to determine if the
resident’s telephone is working.
Buzz on speaker
1. Check for 24 volt AC power shorted to wiring conduit.
2. Check for telephone line shorted to ground.
3. Verify that telephone wires are twisted pair.
4. Verify that the AE-2000 is connected to earth ground.
5. Check 16 VAC voltage at AE-2000 transformer terminals.
Transmitter does not activate relay
1. Transmitter button setting programmed to “none” (would effect all
transmitters).
2. Transmitter not enrolled.
3. Specific transmitter is deactivated in the system.
Buzz on telephone line
1. Disconnect 16 VAC wires from terminal strip, if buzz goes away,
one side of the transformer wires is grounded.
2. Check all connections for any shorts to ground.
Poor transmitter radio range
1. Check antenna installation and condition if transmitters were
previously working well.
System will not answer an incoming call
1. Automatic telephone answer disabled.
2. AE-2000 telephone line trouble.
2. Check the RADIO indicator on the AE-2000 circuit board. If it is
flickering without activating any transmitters there is interference
blocking the receiver. Try adjusting the RECEIVER RANGE knob
to reduce the receiver’s sensitivity to the interference.
3. Connect an audio amplifier or telephone buttset to the RECEIVER
TEST POINTS (the wire jumpers next to the RECEIVER RANGE
knob). Listen to the sounds of the signals being received. If you
hear the interference, remove power from possible interfering
devices to determine the source of the interference. The antenna
or the interfering device may need to be relocated.
Entry code will not activate relay
1. Entry code not assigned.
2. Entry code not set up for proper relay.
3. Keypad is in lockout.
Remote PBUS device does not work
1. Check remote device address switch setting.
2. Check remote device for power.
3. Be sure the device is wired correctly.
4. Use Model FT-1 to check for interference.
Linear Limited Warranty
FCC Notice
This Linear product is warranted against defects in material and
workmanship for twenty-four (24) months.. This warranty extends only
to wholesale customers who buy direct from Linear or through Linear’s
normal distribution channels. Linear does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to
the nature of the dealer’s warranty, if any. There are no obligations
or liabilities on the part of Linear LLC for consequential damages
arising out of or in connection with use or performance of this
product or other indirect damages with respect to loss of property,
revenue, or profit, or cost of removal, installation, or reinstallation.
All implied warranties, including implied warranties for merchantability
and implied warranties for fitness, are valid only until the warranty expires.
This Linear LLC Warranty is in lieu of all other warranties express
or implied.
Changes or modifications not expressly described in this manual or
approved by the manufacturer could void the user’s authority to operate
the equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at
1-800-421-1587 for an RPA# and other important details.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Copyright © 2008 Linear LLC
220231 B
Download from Www.Somanuals.com. All Manuals Search And Download.
|