The modular LINDY KVM Switch CAT-32 IP
The KVM Switch CAT-32 IP provides 32 Cat.5/6 KVM server ports
supporting both USB or PS/2 keyboard and mouse connections via
dedicated USB or PS/2 Cat.5 Computer Modules.
This KVM switch incorporates a modular concept design which allows
for dual console access. The local console port allows direct access
whilst a second console option permits remote access via a remote
KVM over IP module installed in a slot located in the back of the KVM
Switch. This option allows system administrators to access and
administer their servers and KVM switches from a remote office
computer via a web browser. The required optional IP access module
can be simply installed into the back of the KVM Switch at any time.
KVM Switch CAT-32 IP
with KVM over IP Module
User Manual
English
About this manual
This manual is divided into five sections.
•
•
•
The first section is an introduction to the KVM Switch CAT-32
The second section deals with installing and connecting the switch
The third section describes the basic operation of the KVM switch via
its OSD (On Screen Menu)
•
•
Section 4 – left empty for future use
The fifth section describes operation and access via remote IP
KVM Switch CAT-32 IP: LINDY No. 39632
KVM over IP Module:
LINDY No. 39636
Technological progress
The KVM Switch and especially the KVM over IP Module and its
software are subject to technological progress. The products are
continuously upgraded accordingly. Therefore minor changes compared
to the descriptions in this manual may be found.
For Commercial Use Only
Tested to comply
with FCC Standards
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (JAN 2010)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
Introducing the CAT-32 IP
Section 1
Introducing the CAT-32 IP
1.1. Introduction
1.2. CAT-32 with IP access module
Thank you for purchasing this LINDY KVM Switch. Please read this manual carefully to fully
understand the functions and features that the switch offers.
KVM over IP technology allows a simple web browser interface to be used to access the switch
and the connected computers via a local area network (LAN) or, when connected to a wide area
network (WAN), allows access to the switch and the connected computers from almost
anywhere in the world.
Using the LINDY KVM Switch CAT-32 IP a system administrator can access and control several
computers from one compact and high density KVM control center with 32 server ports
occupying only 1U height within a 19” rack.
In addition the KVM Switch CAT-32 allows you to install an optional KVM over IP Remote
Access Module into a slot located in the back of the KVM switch. With this module installed the
administrator can access any of the computers connected to the KVM Switch from any remote
computer on a local LAN or via the Internet using a web browser.
IP Network
KVM
Switch
Local Console
The LINDY KVM Switch CAT-32 allows direct access to up to 32 computers using a single KVM
(Keyboard, Video, and Mouse) either from a local or remote console. To administrate a larger
number of computers multiple switches can be used. They can be either equipped with a KVM
over IP module each or they can easily be daisy chained with an IP module located in the
master KVM switch only.
A dedicated daisy chain port allows a total number of 8 KVM Switches to be connected (daisy
chained) together to control up to 256 computers. Using this daisy chain port method ensures
that none of the computer ports are lost due to cascading. Using IP modules in each KVM
Switch allows users to access even more than 256 computers and provides individual
simultaneous access to every KVM switch with an IP module and by several users.
Remote Access
Multiple Servers
Remote & local control of multiple computers
The CAT-32 KVM Switch supports two methods of switching between the connected
computers: by using keyboard hotkeys or via an OSD (On Screen Display).
The CAT-32 with IP module provides a non-intrusive solution for remote access and control
because the software runs on its embedded processors only, so there’s no interference with
computer operation, or impact on network performance. The IP module also features remote
mass storage support; a USB connection from the switch to a connected computer allows virtual
storage to be set up on the computer as a virtual drive accessed from the client.
The KVM Switch CAT-32 IP has a single user password protection with auto logout security.
The security features for the KVM over IP user are based on SSL and additionally KVM
encrypted connections with a further level of password login.
Doing so any files, folders or local drives at the remote user can be configured as a local drive
at the remote computer allowing for driver installation and updates etc.
1.3. KVM compatibility with other series KVM switches
The KVM Switch CAT-32 is compatible with most other brands of KVM switches using a port
cascaded installation. To prevent any hotkey conflicts, please ensure that the KVM hotkeys of
the other KVM switches used are not the same as those used on the KVM Switch CAT-32 IP.
The KVM hotkeys of the KVM Switch CAT-32 IP can be configured via the OSD.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
Introducing the CAT-32 IP
Section 1
Introducing the CAT-32 IP
1.4. Product Features
1.5. Package Contents
ꢀ
No. 39632, (1) KVM Switch CAT-32
(2) Firmware upgrade cable
(3) Daisy Chain cable
ꢀ
ꢀ
32 UTP Cat.5/6 server ports in a narrow 1U, 19” rack mount design
Dual console operation option: Local console connected by PS/2 and VGA plus a remote
access slot for optional KVM over IP module
(4) Power Adapter
(5) 19" Rackmount Kit
(6) User manuals (English, French, German, Italian)
ꢀ
ꢀ
ꢀ
Compatible with all commonly used operating systems
Supports USB as well as PS/2 computers using the appropriate Computer Modules
Hot Plug Support allows computers to be added or removed for maintenance without
powering down the KVM switch or the computers
ꢀ
No. 39636, (1) KVM over IP Module for KVM Switch CAT-32 IP
(2) USB cable type A/Mini-B
(3) CD with Utilities & Manual (English)
(4) Printed Quick Start Guides (English, French, German, Italian)
ꢀ
ꢀ
ꢀ
High Quality Video – Supports display resolutions of up to 1920 x 1200 at the local console
Supports up to 1280 x 1024 at the IP console, 1600 x 1200 in virtual desktop mode
No Software Required - easy computer selection via the On Screen Display Menu or
Keyboard Hot Keys
1.6. Optional Cables and Accessories
The remote access KVM over IP module, LINDY No. 39636, can be installed at any time.
(To install it into the KVM Switch CAT-32 ensure all connected computers are switched off or
disconnected and the power supply is unplugged. Open the slot on the back of the KVM Switch
and slide the module into the slot.)
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Each computer can be individually named in the On Screen Display Menu
Password log in protection for access to the KVM Switch, auto log out option
SSL security and additional password protection for IP access users
Auto Scan Mode with an adjustable scan time from 5~104 seconds for monitoring computers
Keyboard status automatically restored when switching between computers
Front panel LED indicators for easy status monitoring
The local monitor, PS/2 mouse and PS/2 keyboard is connected using their standard cables.
To connect each individual computer to the switch, Cat.5/6 computer modules are required. For
USB or PS/2 computers different modules have to be used as listed below:
•
•
For PS/2 computers: Cat.5/6 Computer module PS/2 & VGA, LINDY No. 39633
For USB computers: Cat.5/6 Computer module USB & VGA, LINDY No. 39634
2 Digit LED display indicates the cascaded KVM Switch number
32x RJ45 ports for UTP cables to connect to the servers with up to 100m distance each
Separate built-in daisy chain port prevents the loss of any computer port when cascading
A Cat.5e or 6 UTP cable of appropriate length (max. 100m) is required to connect the KVM
Switch to the computer modules. These cables are available from LINDY in several different
colors and lengths from 0.3m up to 100m. We don’t recommend using shielded FTP/STP
cables. Please find a small overview below:
UTP Cat.5e
0.5m 1m
2m
3m
5m
7.5m 10m 15m 20m 30m
45961 45962 45963 45964 45965 45966 45967 45968 45969 45970
40m 50m 60m 70m 80m 90m 100m
45971 45972 44733 45974 44735 44736 45977
UTP Cat.6
0.5m 1m
2m
3m
5m
7.5m 10m 15m 20m 30m
45771 45772 45773 45774 45775 45776 45777 45778 45779 45780
Daisy Chain Cable
A short Daisy Chain Cable is included to cascade KVM switches with each other. Longer cables
are available from LINDY: No. 39637 (1m) and No.39638 (2m).
To reach even longer distances several 2m cables can be chained together.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Hardware Installation
2.1. Hardware Installation Guide
Before you start please verify that all parts are included according to the package contents
listed previously.
Please prepare the required amount of KVM Computer Access Modules and UTP cables to
connect to your computers/servers.
If you want to install the KVM Switch in a 19” server rack please attach the enclosed 19” rack
mount brackets using the screws provided.
Section 2
If you intend to install the optional KVM over IP module then please install it into the
module slot before you connect the servers and the power supply to the KVM Switch.
You may also wish to attach one of the information labels supplied with the KVM over IP
module to the back (or the front) of the KVM Switch so that you can easily locate the IP
modules MAC address.
In addition to the computers/servers to be connected you will need a PS/2 keyboard, monitor
and PS/2 mouse to use as a local console.
Hardware Installation
Cascading / Daisy chaining of multiple KVM Switches
You can integrate up to 8 KVM Switches in one KVM daisy chained installation with up to a
maximum of 256 attached computers.
To connect an additional slave KVM Switch to the MASTER (or previous) KVM switch use a
standard daisy chain KVM cable as mentioned above. Connect it to the Daisy Chain OUT port
of the MASTER KVM switch and to the Daisy Chain IN port of the first slave KVM switch. To
connect the second slave KVM switch connect the Daisy Chain OUT port of the first slave
KVM switch to the Daisy Chain IN port of the second slave KVM switch. Repeat this step up to
a maximum of 8 KVM switches with a maximum of 256 servers.
1. Switch off all the computers to be attached.
2. Connect the keyboard, monitor and mouse directly to the ports of the LINDY KVM
Switch labelled Local Console.
3. Now connect the servers and computers to the ports labelled 1 to 32 using UTP
cable of appropriate length and an appropriate Computer Access Module.
4. Attach the power supply to the KVM Switch. Switch on your monitor.
To set up and configure the KVM over IP remote access modules please refer to section
4 of this user manual.
You may also refer to the printed Quick Start Guide supplied with the KVM over IP
module.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
KVM Switch Operation
3.1. KVM Switch Operation
Please Note: Your monitor will only display one computer signal at any one time. All
keyboard and mouse commands are sent to this computer as shown on the monitor.
When the computer connected to the currently selected port is not switched on,
or is in sleep mode, the monitor will not display any signal.
Section 3
3.1.1. Password Security
The KVM Switch CAT-32 IP has a single user password protection with auto logout security.
The additional security features for the KVM over IP user are based on SSL and additionally
KVM encrypted connections with a further level of password login. Details can be found in
section 5, KVM over IP module.
KVM Switch Operation
3.1.2. Hot Plug Support
The KVM Switch supports a “Hot Plug” function for easy addition or removal of computers.
PS/2 computer modules
If a computer is already running and its PS/2 interface has already been initialized, it is not
required to turn off the computer. Simply hot-plug the PS/2 computer module to the computer.
Always connect the PS/2 mouse port first to allow the correct initialization sequence! If the PS/2
ports of the computer haven't been initialized during boot up it may however be necessary to
turn off the computer before connecting the PS/2 computer module so the OS can initialize the
PS/2 ports during boot up.
Please note: Some Operating Systems including certain Unix versions may be unable to
support the “Hot Plugging” function. If you “Hot Plug” when using this kind of O.S., it may
cause unpredictable operation and may even shut down the computer.
USB computer modules
The USB and VGA interface is hot pluggable on most OS and computer systems. Therefore you
may connect and disconnect USB computer modules at any time. Connect the computer
modules to the KVM Switch using UTP Cat.5e/6 cables of appropriate length. In most cases
standard patch cable UTP Cat.5e or 6 can be used without any problems. For best video results
at very large distances and high resolutions UTP Cat.6 solid core cable may be used to improve
video quality and distance. Shielded FTP/STP is not recommended. After the computers are
connected and powered up you can access them from the KVM Switch CAT-32.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
KVM Switch Operation
Section 3
KVM Switch Operation
3.1.3. Computer / Port Selection
3.3. On Screen Display Menu (OSD)
You can select the computer you want to access in one of two different ways:
The On Screen Display menu provides a lot of information about the switch configuration and
the attached computers, and offers advanced administration and full KVM Switch control to the
user.
ꢀ
ꢀ
Keyboard hotkey selection
On screen display menu selection
Activate the OSD by the hotkey sequence:
Scroll Lock + Scroll Lock + space bar
3.1.4. Illuminated front display
Main OSD Menu
The front display has a two digit display to show the number of the KVM switch in the cascade:
01: Master, 02: first slave, 03: second slave. In addition one LED per Port shows the status of
the connected port:
Select computer/port: use Up/Down Arrow key to
navigate, Page Up/Page Down to scroll page, hit
Enter to select.
GREEN (solid): the computer on this port is powered (switched on or soft off with 5V active)
GREEN (blinking/flickering): this port is currently selected, displayed on the monitor, and
keyboard/mouse commands are sent to the computer attached to this port.
Dark: No computer connected or computer not powered up / no 5V signal active
Edit computer name: just hit Insert to edit and
Enter to confirm.
F2: Save - Save all modifications you have made.
When pressing F2, you will see the message--
"Saving parameters" for confirmation.
F1: Setup - rotate through Main/ Video Setting/
Setup/ Status OSD menu pages
Main OSD Menu
One red Power LED near the bank display shows if the KVM Switch is powered up.
Setup OSD Menu
3.2. Keyboard Hotkey Selection and OSD Commands
Auto logout: specify the timeout before an auto-
logout (00~99 min, +1 min) is performed
OSD Timeout: specify timeout for OSD menu
remaining on screen (00~99 sec, +5 sec)
AutoScan period: Specify the delay time for auto
scan (00~99 sec, +5 sec)
Press the following key combination to enter the OSD menu:
(Factory Default Hotkey is Scroll Lock; it can be changed via the OSD configuration)
Within 2 seconds
Title bar: Specify the title bar position
(Left/Right/Disable)
=
On Screen Display Menu
Scroll
Scroll
Lock
Space bar
In most cases you can select ports via the OSD
display or via the keyboard hotkey commands
+
+
Lock
Hotkey: specify the hotkey preceding sequence
(SCROLL LOCK, CAPS, F12 or NUM LOCK)
Password: Enable/Disable password protection
Enable /Disable Remote Console: Toggle the
remote console On/Off. If the remote console is in
With a small delay the OSD pops up on your monitor and you can use the cursor keys to
navigate through the OSD and select functions by pressing the Return key.
OFF state, a message will remind you appearing
F1 Setup OSD Menu
under the OSD title bar, Remote control disabled
Alternatively, instead of waiting for the OSD, you can press the initial Scroll Lock hotkey twice
and add further direct keyboard hotkey commands within 2 seconds after the initial hotkey to
switch computer ports directly or change the KVM Switch CAT-32 settings etc.
Always press F2 to save any changes!
Video setting Menu
Allows you to adjust video settings individually for
every port:
Further available direct hotkey commands:
Gain: specify level of gain. (00 ~ 50)
Equ: specify level of equalization. (00 ~ 50)
Command
(Cursor up) /
Action
Select next higher/lower port
↑
↓
(Cursor down)
Go to Main/Video setting, and then begin to adjust
the video parameters such as gain/equalization.
Start with equalization to adjust the sharpness and
shadows followed by gain for the brightness. It may
be necessary to try several different settings and
combinations to achieve the best display. Always
press F2 to save any changes!
Page Up / Page Down
H + { Scroll / Num / Caps / ESC / F12 }
0101 ………… 0832
T
Z
S
Select next higher/lower bank/KVM switch
Change primary hotkey
Bank + port number direct selection
OSD port info screen on/off
Remote console on/disabled
Start Autoscan
Video Setting Main Menu
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
KVM Switch Operation
Status Menu
This status page shows information for all
daisy chained KVM Switches: Firmware
version, KVM Switch PCB model and max.
number of ports. Select one bank and press
Enter to access the status pages of the Cat.5
computer modules connected to that KVM
Switch.
Section 4
Intentionally left empty
For future use
Computer Module Status Submenu
Use this page to check the firmware version of
the Cat.5 Computer Modules attached to a
selected KVM Switch (i.e. 120208 shown here
is the FW version of the KVM Switch), and
perform manual FW upgrades. To do a
manual FW upgrade of individual Cat.5
computer modules, just select the module to
be upgraded and press Enter to confirm the
automatic upgrade. During the upgrade
process a download bar will appear indicating
the progress of the upgrade. In addition you
can alternatively press F4 to toggle between
manual and auto (for all Cat.5 modules
connected to this KVM Switch) upgrade mode.
More detailed information is provided with the
Firmware upgrade files.
Status Menu
Section 5
Computer Module Status Submenu
IP Access Configuration &
Operation
Firmware Update
Use the supplied Firmware update cable to connect between the Daisy Chain In port of the
KVM switch and the DB9 RS-232 port on your computer.
3.4. Troubleshooting
Before calling technical support, please try the following steps for easy troubleshooting.
Q1. My keyboard and/or mouse are locked up. What can I do for troubleshooting without
rebooting the computer and/or KVM?
A1. First, unplug the console keyboard and mouse for a few seconds and plug them back in.
This will re-initialize the console keyboard and mouse, in case an initialization failure of the
console keyboard and mouse has happened. If this doesn't work, unplug the computer modules
PS/2 or USB connections from the computer for few seconds and plug it in again - alternatively
plug the USB connector into to a different USB port. If it is PS2, always connect the mouse
connection first, then the keyboard connection. This should bring back the computer module if
only re-initialization is required. If any of the above does not help then you may have to reboot
the computer for a complete reset of the computer keyboard and mouse.
Q2. My monitor stays dark.
A2. Please check if the computer you want to access is in Standby or power save mode with the
monitor switched off. If so please wake up the computer in the usual way.
The contact information for the LINDY technical support teams can be found on the LINDY
website for each country.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
5.0.1. KVM over IP Access Features
5.1. Configuration
The IP access module provides remote KVM over IP access to the KVM switch CAT-32. It
converts all keyboard video and mouse signals and sends them as TCP/IP signals over your
LAN/WAN connection. The KVM switch CAT-32 IP may be accessed from any computer
connected to your network and provides full KVM access including BIOS level access to all the
connected computers.
The CAT-32 IP’s communication interfaces
are all based on TCP/IP. The switch comes
pre-configured with the following IP
configuration shown here:
Parameter
IP auto configuration
IP-Address
Net-mask
Default-Gateway
Value
DHCP
-
255.255.255.0
none
Please note that KVM over IP does not operate in a “real time” environment and that some
degree of time delay will occur due to limiting factors such as available bandwidth and network
traffic.
Note: If the DHCP connection fails on boot-up, the CAT-32 IP will not be assigned an IP
address.
If this initial configuration does not meet your requirements, the following section describes the
configuration that is necessary to access the CAT-32 IP for the first time.
The KVM over IP Access module can be accessed via a simple web browser and via dedicated
software tools included with the product. It uses secure encrypted sessions and password
authentication protocols.
Initial Configuration via a DHCP Server
Please note that the conversion of video, mouse and keyboard signals requires a certain
amount of CPU processing time. Transporting large amounts of data over TCP/IP requires a
high bandwidth connection. Limited bandwidth may restrict or limit the possible screen
resolutions and colour depths which can be transmitted over your LAN / WAN.
By default, the CAT-32 IP will try to contact a DHCP server in the subnet to which it is physically
connected. If a DHCP server is found, it will provide a valid IP address, gateway address and
subnet mask. If a DHCP server is not available then you will need to assign a fixed IP
assignment to the MAC address of the IP Access Module. You can find the MAC address
details on the printed label on the underside of the IP Access module.
A connection which exhibits limited bandwidth will result in slower mouse reaction and cursor
control. Also the available screen resolution, colour depth and refresh rates will also be affected.
Ensure the connection you are using provides adequate bandwidth, some adjustment of screen
resolution, colour depth and mouse cursor control may have to be made for satisfactory
operation.
Before you connect the device to your local subnet, be sure to complete the corresponding
configuration using the setup tool supplied on the CD ROM. Follow the procedure described on
the next page (Section 5.2)
Initial Configuration via a Serial Console
5.0.2 KVM over IP Access Module Installation
The CAT-32 IP has a serial line interface (host side)
for connecting a serial terminal. This connector is
compliant with the RS232 serial line standard. The
serial line has to be configured with the parameters
given in this table:
Parameter
Bits/second
Data bits
Parity
Stop bits
Value
115200
8
No
1
Before you install the IP Access module into the KVM switch ensure all connected computers
are switched off and the power supply is unplugged. Proceed to unscrew and remove the small
metal cover on rear of the KVM switch. Carefully slide the module into the slot and secure in
place with the screw previously removed.
Flow Control
None
When configuring with a serial terminal, reset the CAT-32 IP and immediately press the ESC
key. You will see some device information and a “=>” prompt. Type config and press the Enter
key. Wait a few seconds for the configuration information to appear.
You may now proceed to power up all connected equipment and check for correct operation.
As you proceed, the following questions will appear on the screen. To accept the default values
(shown in square brackets below) press the Enter key.
For the remainder of this manual the CAT-32 KVM switch with installed KVM
over IP Module will be referred to as CAT-32 IP.
IP auto configuration (non/dhcp/bootp) [dhcp]:
IP [192.168.1.22]:
Net mask [255.255.255.0]:
Gateway (0.0.0.0 for none) [0.0.0.0]:
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Authentication
5.2 CAT-32 IP Setup Tool
To adjust the authentication settings, enter your login as a super user and change your
password.
MAC Address Detection
Connect the CAT-32 IP to your computer either via a local network, or via USB. If you use a
USB connection Windows will detect the CAT-32 IP as a ‘Removable Disk’ and an appropriate
drive letter will be assigned.
Super user login
Enter the login name of the super user. The initial value is "super". All of the characters are
lower case.
Start the setup tool from the CD ROM.
A window opens as shown below:
Super user password
Enter the current password for the super user. This initial value is "pass". All of the characters
are lower case.
New super user password
Enter the new password for the super user.
New password (confirm)
Re-type the new password for the super user.
To close the window and accept the changes, press the OK button, otherwise press the Cancel
button.
IP Auto Configuration
With this option, you can specify whether the CAT-32 IP should obtain its network settings from
a DHCP or BOOTP server. From the drop down list select either DHCP or BOOTP. If you
select NONE, the IP auto configuration is disabled and you should manually input the following
network settings:
IP address
The IP address the CAT-32 IP uses.
Net mask
The net mask of the connected IP subnet.
Gateway address
On the upper left corner, the MAC address of the CAT-32 IP is displayed. To re-detect the MAC
address, press the Refresh Devices button. The displayed MAC address should correspond to
the printed address shown on the label on the base of the IP module.
The IP address of the default router for the connected IP subnet. If you do not have a default
router, enter 0.0.0.0.
On the lower right corner of the window, there are two buttons: Query Device and Setup
Device. Press the Query Device button to display the preconfigured values of the network
configuration. The values are displayed in the text fields located above. If necessary, adjust the
network settings to your needs. To save the changes enter a user login and a password (see
Authentication, below) and then press the Setup Device button.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Host System Mouse Settings
5.3. Keyboard, Mouse and Video Configuration
The host's operating system obtains various settings from the mouse driver.
Note: The following limitations do not apply when using USB mice and
Windows 2000 and higher!
Between the CAT-32 IP and the host, there are two interfaces available for transmitting
keyboard and mouse data: USB and PS/2. The correct operation of the remote mouse depends
on several settings which will be discussed in the following subsections and section 5.7.4.
Special Mouse Driver
There are mouse drivers which influence the synchronization process and lead to
desynchronized mouse pointers. If this happens, make sure you do not use a special vendor-
specific mouse driver on your host system.
CAT-32 IP Keyboard Settings
The CAT-32 IP settings for the host's keyboard type have to be correct in order to make the
remote keyboard work properly. The settings can be checked using the CAT-32 IP front-end,
please see section 5.7.4 for details of how to make changes to the keyboard settings.
Windows XP Mouse Settings
If using Windows XP, disable the enhance pointer precision setting.
Active Desktop
Remote Mouse Settings
If the Active Desktop feature of Microsoft Windows is enabled, do not use a plain background.
Instead, use some kind of wallpaper. Alternatively, you could also disable the Active Desktop
completely.
Navigate your mouse pointer into the upper left corner of the applet screen and move it back
and forth slightly. In this way the mouse will be resynchronized. If re-synchronizing fails, disable
mouse acceleration and repeat the procedure.
A common problem with KVM devices is the synchronization between the local and remote
mouse cursors. The CAT-32 IP addresses this problem with an intelligent synchronization
algorithm. There are two mouse modes available on the CAT-32 IP: Auto mouse speed and
Fixed mouse speed.
Auto mouse speed
Single and Double Mouse Mode
The automatic mouse speed mode tries to detect the speed and acceleration settings of the
host system automatically. Speed detection is performed during mouse synchronization. If the
mouse does not move correctly, there are two ways to re-synchronize the local and remote
mouse:
The information above applies to Double Mouse Mode, where both remote and local mouse
pointers are visible and need to be synchronized. The CAT-32 IP also features another mode -
Single Mouse Mode, where only the remote mouse pointer is visible. Activate this mode in the
open Remote Console and click into the window area. The local mouse pointer will be hidden
and the remote one can be controlled directly. To leave this mode, use the hotkey combination
[ALT] + [F12] to free the captured local mouse pointer.
Fast Sync: Fast synchronization is used to correct a temporary, but fixed skew. Choose this
option using the Remote Console options menu or by pressing the mouse synchronization
hotkey sequence - [ALT] + [F12]
Recommended Mouse Settings
Intelligent Sync: If the fast sync does not work correctly or the mouse settings have been
changed on the host system, you can use the intelligent resynchronization option. This method
can be accessed from the Mouse Handling sub menu of the Remote Console Option menu.
For the different operating systems we can give the following advice...
MS Windows 2000/2003 (Professional and Server), XP, Vista,
In general, we recommend the use of a USB mouse. Choose USB without Mouse Sync. For a
PS/2 mouse choose Auto Mouse Speed.
For XP, Vista, disable the option called enhance pointer precision or similar in the Control
Panel.
Intelligent synchronization requires a correctly adjusted picture. Use the auto adjustment
function or manual correction in the Video Settings panel to setup the picture. The Sync mouse
button on top of the Remote Console can behave differently, depending on the current
state of mouse synchronization. Usually pressing this button leads to a fast sync, except in
situations where the KVM port or the video mode was recently changed.
SUN Solaris
Adjust the mouse settings either via xset m 1 or use the CDE Control Panel to set the mouse to
1:1, no acceleration. As an alternative you may also use the Single Mouse Mode.
Tip: When first started, if the local mouse pointer is not synchronized with the remote mouse
pointer, click the Auto Adjust Button once. If the mouse is still not synchronized select
Intelligent Sync from the Mouse Handling sub menu of the Remote Console Option menu.
MAC OS X
We recommend using the Single Mouse Mode.
Video Modes
Fixed mouse speed
This mode just translates the mouse movements from the Remote Console in a way that one
pixel move will lead to ‘n’ pixel moves on the remote system. This parameter ‘n’ is adjustable.
However, it should be noted that this works only when mouse acceleration is turned off on the
remote system.
The CAT-32 IP switch recognizes a limited number of common video modes. When running
X11 on the host system, please do not use any custom mode lines with special video modes. If
you do, the CAT-32 IP switch may not be able to detect them. We recommend using any of the
standard VESA video modes instead.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
5.4. Usage
5.5. Logging In
Prerequisites
Login to the CAT-32 IP
Launch your web browser. Direct it to the address of your CAT-32 IP which you configured
during the installation process. The address used might be a plain IP address or a host and
domain name if you have given your CAT-32 IP switch a symbolic name in the DNS.
The CAT-32 IP features an embedded operating system offering a variety of standardized
interfaces. This section will describe these interfaces, and the way to use them in a more
detailed manner. The interfaces are accessed using the TCP/IP protocol family.
Example: Type the following in the address line of your browser when establishing an
unsecured connection:
The following interfaces are supported:
Telnet
A standard Telnet client can be used to access an arbitrary device connected to the CAT-32
IP’s serial port via a terminal.
When using a secure connection, type in:
HTTP/HTTPS
Full access is provided by the embedded web server. The CAT-32 IP switch environment can
be entirely managed using a standard web browser. You can access the CAT-32 IP using the
insecure HTTP protocol, or using the encrypted HTTPS protocol. Whenever possible, use
HTTPS.
This will lead you to the CAT-32 IP login page as shown below:
The primary interface of the CAT-32 IP is the HTTP interface. This is covered extensively in this
section. Other interfaces are addressed in the relevant subsections.
In order to use the Remote Console window of your managed host system, the browser must
feature Java Runtime Environment version 1.1 or higher support. If the browser has no Java
support (such as on a small handheld device), you can still maintain your remote host system
using the administration forms displayed by the browser itself.
Important: We recommend you install the latest version of Sun’s
Java Virtual Machine which can be downloaded from the
following web site:
The CAT-32 IP has a built-in super user account that has all the permissions enabled to
administrate your CAT-32 IP switch:
Login name super (factory default)
For a non-secure connection to the CAT-32 IP, we recommend the following browsers:
Password
pass (factory default)
ꢀ
ꢀ
Microsoft Internet Explorer version 6.0 or higher
Netscape Navigator 7.0 or Mozilla 1.6
Please note: Your web browser has to accept cookies, or else login is not possible.
Note: The user “super” is not allowed to login via the serial interface of the IP-KVM switch.
In order to access the remote host system using a securely encrypted connection, you need a
browser that supports the HTTPS protocol. Strong security is only assured by using a key
length of at least 128 Bit. Some older browsers do not have a strong 128 Bit encryption
algorithm.
Please make sure you change the super user password immediately after you have installed
and accessed your CAT-32 IP for the first time. Not changing the password for the super user is
a severe security risk and could result in unauthorized access to the switch and to the host
system(s) to which it is connected.
Technological progress
The KVM over IP Module, its software and firmware are subject to technological progress
and are being continuously upgraded accordingly. Therefore minor changes compared to
the descriptions in this manual may be found, especially for the design of the screens and
menus.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
The Remote Console is the redirected screen, keyboard and mouse of the remote host system
that the CAT-32 IP switch controls. Selecting this button opens the Remote Console Main
Window.
5.6. Navigation
Once logged into the CAT-32 IP successfully, the main page appears. This page consists of
three parts; each of them contains specific information. The buttons in the upper area allow you
to navigate within the front end. The lower left area contains a navigation bar and allows you to
switch between the different sections of the CAT-32 IP. Within the main area, task-specific
information is displayed.
The Remote Console window is a Java Applet that establishes its own TCP connection to the
CAT-32 IP. The protocol that runs over this connection is neither HTTP nor HTTPS, but RFB
(Remote Frame Buffer Protocol). RFB needs to establish a connection to port number 443. Your
local network environment has to allow this connection to be made, i.e. your firewall and, if you
have a private internal network, your NAT (Network Address Translation) settings have to be
configured accordingly.
If the CAT-32 IP is connected to your local network environment and your connection to the
Internet is available using a proxy server only, without NAT being configured, the Remote
Console is very unlikely to be able to establish a connection. This is because today's web
proxies are not capable of relaying the RFB protocol.
If you experience problems, please consult your network administrator in order to provide an
appropriate network environment.
Remote Console Main Window
Return to the main page of the CAT-32 IP
Logout from the CAT-32 IP
This link logs out the current user and presents a new login screen. Please note that an
automatic logout will be performed if there is no activity for half an hour. Clicking one of the links
will bring you back to the login screen.
Starting the Remote Console opens an additional window. It displays the screen content of the
currently selected computer connected to the CAT-32 IP. The Remote Console will behave in
exactly the same way as if you were using the local console. You can use the CAT-32 IP
keyboard hotkeys to switch between computers, activate the OSD etc., as well as control the
currently selected computer. However, be aware that the host system will react to keyboard and
mouse actions with a slight delay.
Access the Remote Console
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Note: Your local keyboard changes its keyboard layout according to the remote host system. If
you use a German administration system and your host system uses a US English keyboard
layout for instance, some special keys on the German keyboard will not work as expected.
Instead, the keys will result in their US English counterpart. You can circumvent such problems
by adjusting the keyboard of your remote system to the same mapping as your local one.
Options
Opens the Options menu. A short description of the each of the options follows:
Monitor Only
Toggles the ‘Monitor only’ filter on or off. If the filter is switched on, no remote console
interaction is possible but monitoring is.
The Remote Console window always tries to show the remote screen with its optimal size. That
means it will adapt its size to the size of the remote screen initially and after the screen
resolution of the remote screen has been changed. However, you can always resize the
Remote Console window in your local window system as usual.
Exclusive Access
If a user has the appropriate permission, he can force the Remote Consoles of all other users to
close. No one can open the Remote Console at the same time again until this user disables the
exclusive access, or logs off.
Remote Console Control Bar
The upper part of the Remote Console window contains a control bar. Using its elements you
can see the state of the Remote Console and influence the local Remote Console settings. A
description for each control follows.
A change in the access mode is also visible in the status line indicated by this icon.
Scaling
Allows you to scale down the Remote Console. You can still use both mouse and keyboard;
however the scaling algorithm will not preserve all display details.
Mouse Handling
The submenu for mouse handling offers two options for synchronizing the local and the remote
mouse pointer.
Ctrl+Alt+Delete
Sends the ‘Control Alt Delete’ key combination to the remote system
Fast Sync
The fast synchronization is used to correct a temporary, but fixed skew.
Auto Adjust button
If the video display is poor quality or distorted in some way, click this button and wait a few
seconds while the CAT-32 IP tries to adjust itself for the best possible video quality.
Intelligent Sync
Use this option if the fast sync does not work or the mouse settings have
been changed on the host system
Sync mouse
Note: This method takes more time than fast sync and requires a correctly
adjusted picture. Use the auto adjustment function or the manual correction in
the Video Settings panel to setup the picture.
Activates the mouse synchronization process. Choose this option in order to synchronize the
local AND remote mouse cursors. This is especially necessary when using accelerated mouse
settings on the host system. In general, there is no need to change mouse settings on the host.
Local Cursor
Offers a list of different cursor shapes to choose from for the local mouse pointer. The selected
shape will be saved for the current user and activated the next time this user opens the Remote
Console. The number of available shapes depends on the Java Virtual Machine; a version of
1.2 or higher offers the full list.
Single/Double mouse mode
Switches between the Single Mouse Mode (where only the remote mouse pointer is visible) and
the Double Mouse Mode (where remote and local mouse pointers are visible) Single mouse
mode is only available if using SUN JVM 1.3 or higher.
Video Settings
Opens a panel for changing the CAT-32 IP video settings. The CAT-32 IP features two different
dialogs, which influence the video settings:
Tip: When in single mouse mode use the hotkey combination [ALT] + [F12] to release
mouse control and access the menus etc.
Video Settings in the KVM section in the front end menu:
The Noise Filter option defines how the CAT-32 IP reacts to small changes in the video input
signal. A large filter setting needs less network traffic and leads to a faster video display, but
small changes in some display regions may not be recognized immediately. A small filter
displays all changes instantly but may lead to a constant amount of network traffic even if
display content is not really changing (depending on the quality of the video input signal). All in
all the default setting should be suitable for most situations.
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Video Settings through the remote console:
Undo Changes
Restore last settings
Soft Keyboard
Opens up the sub-menu for the Soft-Keyboard:
Show
Pops up the Soft-Keyboard. The Soft-Keyboard is necessary in case your host system runs a
completely different language and country mapping than your administration machine.
Brightness
Controls the brightness of the picture
Mapping
Contrast
Used for choosing the language and country mapping of the Soft-Keyboard.
Controls the contrast of the picture
Local Keyboard
Clock
Used to change the language mapping of your browser running the Remote Console Applet.
Normally, the applet determines the correct value automatically. However, depending on your
particular KVM and your browser settings this is not always possible. A typical example is a
German localized system that uses a US-English keyboard mapping. In this case you must
manually change the local keyboard setting to the correct language.
Defines the horizontal frequency for a video line and depends on the video mode. Different
video card types may require different values here. The default settings in conjunction with the
auto adjustment procedure should be adequate for most common configurations. If the picture
quality is still bad after auto adjustment you may change this setting together with the sampling
phase to achieve a better quality.
Hotkeys
Phase
Opens a list of previously defined hotkeys. Choose one entry; the command will be sent to the
host system.
Defines the phase for video sampling; used to control the display quality together with the
setting for sampling clock.
A confirmation dialog can be added that will be
displayed before sending the selected command
to the remote host. Select OK to perform the
command on the remote host.
Horizontal Offset
Use the left and right buttons to move the picture in a horizontal direction
Vertical Offset
Use the left and right buttons to move the picture in a vertical direction
Reset this Mode
Reset mode specific settings to the factory-made defaults.
Reset all Modes
Reset all settings to the factory-made defaults.
Save Changes
Save changes permanently
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Remote Console Status Line
Status line
Shows both console and the connection state. The size of the remote screen is displayed. The
example below was taken from a Remote Console with a resolution of 1024 x 768 pixels. The
value in brackets describes the connection to the Remote Console. Norm means a standard
connection without encryption, SSL indicates a secure connection.
5.7. Menu Options
Technological progress
The KVM over IP Module and its software and firmware are subject to technological
progress and are being continuously upgraded accordingly. Therefore minor changes
compared to the descriptions in this manual may be found, especially for the design of the
screens and menus.
5.7.1. Remote Control
KVM Console
Furthermore, both the incoming (In :) and the outgoing (Out :) network traffic are visible (in
kb/s). If compressed encoding is enabled, a value in brackets displays the compressed transfer
rate.
For more information about Monitor Only and Exclusive Access settings, see the relevant
section 5.7.4.
To open the KVM console, click either the menu entry on the left or on the console picture on
the right. To refresh the picture, click on the Refresh button.
Remote Power
Future firmware updates will allow you to control external RS232 controlled power control
distribution units. Please contact LINDY for further information regarding compatibility,
connection and configuration of both LINDY and third party power control distribution units.
Should you wish to connect a remote power outlet then LINDY would recommend you to use IP
managed power strips that can be found in the network section of the LINDY website, i.e.
LINDY No. 32657, 32658, 32656, 32654, 32653, 32414, 32415
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
The following list shows the command mode syntax and usage.
Telnet Console
Help
Displays the list of possible commands
Cls
Clears the screen
Quit
Exits the current session and disconnects from the client
Version
Displays the release information
Terminal
Starts the terminal pass-through mode for the serial port. The key sequence ‘esc exit’ switches
back to the command mode.
The CAT-32 IP firmware features a Telnet server that enables a user to connect via a standard
Telnet client. If the Telnet program is using a VT 100, VT 102 or VT 220 terminal or appropriate
emulation, it is even possible to perform a console redirection, as long as the CAT-32 IP host is
using a text mode screen resolution.
Connecting to the CAT-32 IP is done as usual and as required by the Telnet client, for instance
in a UNIX shell:
telnet 192.168.1.22
Replace the IP address by the one that is actually assigned to the CAT-32 IP. This will prompt
for the username and password in order to log into the device. The credentials that need to be
entered for authentication are identical to those of the web interface. That means the user
management of the Telnet interface is entirely controlled with the appropriate functions of the
web interface.
Once you have successfully logged into the CAT-32 IP a command line will be presented and
you can enter management commands directly.
In general, the Telnet interface supports two operation modes: the command line mode and the
terminal mode. The command line mode is used to control or display some parameters. In
terminal mode the pass-through access to serial port 1 is activated (if the serial settings were
made accordingly). All inputs are redirected to the device on serial port 1 and its answers are
displayed on the Telnet interface.
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Windows
5.7.2. Virtual Media
Windows users should use the tool, RawWrite for
Windows, which is included on the supplied CD.
One of the computers connected to the CAT-32 IP can also be set up for remote mass storage
via a USB connection. Files can be uploaded to the switch, which the host computer ‘sees’ as
virtual drives. This means the remote operator can remotely install software, drivers etc. without
the need to be sat in front of the host computer.
Launch RawWrite, you will see the window
opposite:
Insert your floppy disk into your floppy drive. Click
the Read tab and then click on
Floppy Disk
Select a name and destination for the floppy image
file and click the Read button. As the image is
written, you will see the progress as a percentage
figure in the bottom left hand corner.
When the image has been written you can upload it
to the CAT-32 IP.
Uploading a Floppy Image
Click the Browse button and navigate to
the location of the image file, then click
the Upload button.
After the image has uploaded you will see the dialog below:
Follow the steps below to upload a virtual floppy image to the CAT-32 IP and create a virtual
floppy drive on the host system.
Create a Floppy Image
First, on your client PC you must create an image of your floppy disk which can be uploaded to
the CAT-32 IP’s built in memory.
UNIX and UNIX-like OS
To create an image file, make use of dd. This is one of the original UNIX utilities and is included
in every UNIX-like OS (UNIX, Sun Solaris, and Linux).
A virtual floppy drive will be installed on the host system and the image will be downloaded to
the virtual floppy drive from the CAT-32 IP. You can access the virtual floppy drive in the same
way you would a regular drive.
To create a floppy image file copy the contents of a floppy to a file. You can use the following
command:
You can download the image from the CAT-32 IP to your remote system by clicking the
Download button.
dd [ if=/dev/fd0 ] [ of=/tmp/floppy.image ]
Clicking Discard removes the virtual floppy image from the CAT-32 IP and from the hosts
system.
dd reads the entire disc from the device /dev/fd0 and saves the output in the specified output
file /tmp/floppy.image. Adjust both parameters exactly to your needs (input device etc.)
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Windows
Create a CD-ROM/ISO Image
To create the image file, use your favorite CD
imaging tool. Copy the whole contents of the disc
into one single image file on your hard disk.
For example, with ‘Nero’ choose ‘Copy and
Backup’. Then, navigate to the ‘Copy Disc’
section. Select the CD ROM or DVD drive you
would like to create an image from. Specify the
filename of the image, and save the CD ROM
content in that file.
Example:
1. Create a CD image and name it image.iso
2. Create a folder on your client PC and name it
Test. Copy the file image.iso to the folder
Test.
3. Now you need to ‘share’ this folder. Right click
on the folder and select the option Sharing
and Security. Select Share this folder and
ensure the Share Name is set to Test. Click
Permissions to set permissions for users who
access this folder, according to your
requirements. Click Apply then OK to
complete.
Follow the procedure below to create a CD-ROM image which can be accessed by the host
system via the CAT-32 IP. The image file must be an ISO file format!
First, on your client PC you must create an image of your CD which can be accessed by the
host system.
4. Next you need to mount the image via a
Windows Share. In the CAT-32 IP menu on
the left hand side of the browser select Virtual
Media and from the sub menu select CD-
ROM Image.
UNIX and UNIX-like OS
To create an image file, make use of dd. This is one of the original UNIX utilities and is included
in every UNIX-like OS (UNIX, Sun Solaris, and Linux).
To create a CD-ROM image file, copy the contents of the CD-ROM to a file. You can use the
following command:
5. Input the following parameters:
dd [ if=/dev/cdrom ] [ of=/tmp/cdrom.image ]
Share host:
Share name:
Path to image:
User:
Enter the IP address of your Console PC here (e.g. 192.168.2.103)
Test
(The share name of the previously created folder)
(the name of the CD image)
dd reads the entire disc from the device /dev/cdrom, and saves the output in the specified
output file /tmp/cdrom.image. Adjust both parameters exactly to your needs (input device etc.).
image.iso
super
pass
(Your user name, the default is super)
(Your password, the default is pass)
Password:
6. Click Set
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
7. You will see the dialog below detailing the active image:
Drive Redirection
8. Click Reactivate. Access the console window and you will see that another CD drive has
been installed on the host computer. This is the virtual drive you have just set up. You can
access the uploaded CD image as though it were a regular CD. Click Unset to remove the
image.
The Drive Redirection feature allows the host system to access the CD-Rom drives, hard drives,
floppy drives etc. on your client PC.
To use this feature you need the Drive Redirection Tool which is part of the KVM Vision Viewer
application included on the supplied CD.
SAMBA
If you would like to access the share via SAMBA, SAMBA must be set up properly. You may
either edit the SAMBA configuration file /etc/samba/smb.conf, or use the Samba Web
Administration Tool (SWAT) or WebMin to set the correct parameters.
1. To set up Drive Redirection, first install KVM Vision Viewer. After installation launch the
application:
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
2. Click on the Search for new devices icon -
The CAT-32 IP will be detected as an
1. Choose the drive you wish to redirect from the
drop-down list. Enter your user name and
password and click OK.
Unconfigured device and its MAC address will be displayed in the left panel. Double click
on the MAC address to launch the Device Configuration Wizard.
3. Follow the on-screen instructions. You will be asked to input your user name (default is
super) and password (default is pass).
Warning: Please be aware that if Allow
Write Support is selected, data on the
shared media may be lost!
2. Access the host computer from the Remote Console window. You will see that the
redirected drive will now be shown in Windows Explorer:
4. Continue with the Wizard until the device is correctly configured. Once the configuration is
complete, select Redirect Local Drive from the Device menu:
IMPORTANT
1. Drive Redirection is only possible with Windows 2000 and later versions.
2. Drive Redirection works on a low SCSI level. The SCSI protocol cannot recognize
partitions; therefore the whole drive selected will be shared instead of any
particular partition.
Options
This option allows you to disable the mass storage emulation (and hide the virtual drive) if no
image file is currently loaded. To set this option, press the button Apply.
40
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
5.7.3. User Management
Users And Groups
The CAT-32 IP comes with 2 pre-configured user accounts that have fixed permissions. The
super account has all possible rights to configure the device and to use all functions. The user
account has only the permission to open and use the Remote Console. The default password
for both accounts is "pass". Ensure you change the passwords as soon as you have installed
and accessed the CAT-32 IP for the first time.
Change Password
To change your password, enter the new password in the upper entry field. Retype the
password in the lower field. Click Apply to submit your changes.
While the user account never sees the following options, the super account can change the
name and password for both accounts.
Existing users
Select an existing user for modification. Once a user has been selected, click the lookup button
to see the user information.
New User name
The new user name for the selected account.
Password
The password for the login name. It must be at least four characters long.
Confirm password
Confirmation of the above password.
42
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Manually
5.7.4. KVM Settings
Allows adjustment of both compression rate and colour depth individually. Depending on the
selected compression rate the data stream between the CAT-32 IP and the Remote Console
will be compressed in order to save bandwidth. Since high compression rates are very time
consuming, they should not be used when several users are accessing the CAT-32 IP
simultaneously.
User Console
The following settings are user specific. This means the super user can customize these
settings for individual users separately. Changing the settings for one user does not affect the
settings for the other users.
The standard colour depth is 16 bit (65536 colours). The other colour depths are intended for
slower network connections in order to allow a faster transmission of data. Therefore
compression level 0 (no compression) uses only 16 bit colour depth. At lower bandwidths only 4
bit (16 colours) and 2 bit (4 grey scales) are recommended for typical desktop interfaces. Photo-
like pictures have best results with 4 bit (16 grey scales). 1 Bit colour depth (black/white) should
only be used for extremely slow network connections.
Remote Console Type
Specifies, which Remote Console Viewer to use.
Default Java-VM
Uses the default Java Virtual Machine of your Browser. This may be the Microsoft JVM for
Internet Explorer or the Sun JVM if it is configured this way. Use of the Sun JVM may also be
forced (see below).
User select Unit
This box displays the user ID for which the values are shown and for which the changes will
take effect. You may change the settings of other users if you have the necessary access rights.
Transmission Encoding
The Transmission Encoding setting allows changing the image-encoding algorithm that is used
to transmit the video data to the Remote Console window. It is possible to optimize the speed of
the remote screen depending on the number of users working at the same time and the
bandwidth of the connection line (Modem, ISDN, DSL, LAN, etc.).
Automatic detection
The encoding and the compression level are determined automatically from the available
bandwidth and the current content of the video image.
Pre-configured
The pre-configured settings deliver the best result because of optimized adjustment of
compression and colour depth for the indicated network speed.
44
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Keyboard/Mouse
Sun Microsystems Java Browser Plug-in
Instructs the web browser of your administration system to use Sun’s JVM. The JVM in the
browser is used to run the code for the Remote Console window which is actually a Java
Applet. If you check this box for the first time on your administration system and the appropriate
Java plug-in is not already installed on your system, it will be downloaded and installed
automatically. However, in order to make the installation possible, you still need to answer the
appropriate dialogs with yes. The download size is around 11MB. The advantage of
downloading Sun's JVM is in providing a stable and identical Java Virtual Machine across
different platforms. The Remote Console software is optimized for Sun JVM versions and offers
wider range of functionality when run with JVM.
Miscellaneous Remote Console Settings
Start in Monitor Mode Sets the initial value for the monitor mode. By default the
monitor mode is off. In case you switch it on, the Remote Console window will be
started in a read only mode.
Start in Exclusive Access Mode Enables the exclusive access mode
immediately at Remote Console startup. This forces the Remote Consoles of all
other users to close. No one can open the Remote Console at the same time
again until this user disables the exclusive access or logs off.
Mouse hotkey
Allows the user to specify a hotkey combination which starts either the mouse synchronization
process if pressed in the Remote Console or is used to leave the single mouse mode.
Remote Console Button Keys
This allows simulating keystrokes on the remote system that cannot be generated locally. The
reason for this might be a missing key or the fact that the local operating system of the Remote
Console is unconditionally catching this keystroke already. Typical examples are
Control+Alt+Delete in Windows and DOS, which is always caught, or Control+Backspace on
Linux for terminating the X-Server. The syntax to define a new Button Key is as follows:
Host Interface
Enables the interface the mouse is connected to. You can choose between Auto for automatic
detection, USB for a USB mouse, or PS/2 for a PS/2 mouse.
Note: To use the USB and/or PS/2 interface you need the correct cabling between the
managed host and the managing device. If the managed host has no USB keyboard support
in the BIOS and you have connected the USB cable only, then you will have no remote
keyboard access during the boot process of the host. If USB and PS/2 are both connected
and you selected Auto as host interface, then USB will be selected if available, otherwise it
will revert to PS/2.
[confirm] <keycode>[+|-[*]<keycode>]*
confirm requests confirmation by a dialog box before the key strokes will be sent to the remote
host.
keycode is the key to be sent. Multiple key codes can be joined with a plus, or a minus sign.
The plus sign builds key combinations; all keys will be pressed until a minus sign or the end of
the combination is encountered. In this case all pressed keys will be released in reversed
sequence. So the minus sign builds single, separate key presses and releases. The star inserts
a pause with duration of 100 milliseconds.
To enable USB remote keyboard access during the boot process of the host, the following
conditions must be fulfilled:
ꢀ
ꢀ
the host BIOS must have USB keyboard support
the USB cable must be connected or must be selected in the Host interface option
PS/2 Keyboard Model
Enables a certain keyboard layout. You can choose between Generic 101-Key PC for a
standard keyboard layout, Generic 104-Key PC for a standard keyboard layout extended by
three additional windows keys, Generic 106-Key PC for a Japanese keyboard, and Apple
Macintosh for the Apple Macintosh.
46
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
USB Mouse Type
Force Composite Sync (Required for Sun Computers)
Enables USB mouse type. Choose between MS Windows 2000 or newer for MS Windows
2000 or Windows XP, or Other Operating Systems for MS Windows NT, Linux, or OS X. In MS
Windows 2000 or newer mode the remote mouse is always synchronized with the local
mouse.
To support signal transmission from a Sun machine, enable this option. If not enabled the
picture of the remote console will not be visible. To set the options, click Apply.
5.7.5. Device Settings
Mouse Speed
Network
ꢀ
ꢀ
Auto mouse speed Use this option if the mouse settings on the host use an additional
acceleration setting. The CAT-32 IP tries to detect the acceleration and speed of the mouse
during the mouse sync process.
Fixed mouse speed Use a direct translation of mouse movements between the local and
the remote pointer.
The Network Settings panel allows network related parameters to be changed. Each parameter
will be explained below. Once applied the new network settings will immediately come into
effect.
You may also set a fixed scaling which determines the amount the remote mouse pointer is
moved when the local mouse pointer is moved by one pixel. This option only works when the
mouse settings on the host are linear. This means that there is no mouse acceleration involved.
To set the options, click on the Apply button.
Video
Note: The initial IP configuration is usually done directly at the host system using the
special procedure in the beginning of Section 5.
Changing the network settings of the KVM over IP module might result in losing connection to
it. In case you change the settings remotely make sure that all the values are correct and you
still have an option to access the KVM over IP module.
Miscellaneous Video Settings
Noise filter
This option defines how the CAT-32 IP reacts to small changes in the video input signal. A large
filter setting needs less network traffic and leads to a faster video display, but small changes in
some display regions may not be recognized immediately. A small filter displays all changes
instantly but may lead to a constant amount of network traffic even if the display content is not
really changing (depending on the quality of the video input signal). In general the default
settings should be suitable for most situations.
48
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Dynamic DNS
IP auto configuration
With this option you can control if the CAT-32 IP should obtain its network settings from a
DHCP or BOOTP server. For DHCP, select dhcp, and for BOOTP select bootp. If you choose
none then IP auto configuration is disabled.
A freely available Dynamic DNS service (dyndns.org) can be used in the following scenario (see
illustration below)
IP address
IP address in the usual dot notation.
Subnet Mask
The net mask of the local network.
Gateway IP address
In case the CAT-32 IP is accessible from networks other than the local one, this IP address
must be set to the local network router's IP address.
Primary DNS Server IP Address
IP address of the primary Domain Name Server in dot notation. This option may be left empty;
however, the CAT-32 IP will not be able to perform name resolution.
Secondary DNS Server IP Address
IP address of the secondary Domain Name Server in dot notation. It will be used in case the
Primary DNS Server cannot be contacted.
Remote Console and HTTPS port
Port number at which the CAT-32 IP’s Remote Console server and HTTPS server are listening.
If left empty the default value will be used.
HTTP port
The CAT-32 IP is reachable via the IP address of the DSL router, which is dynamically assigned
by the provider. Since the administrator does not know the IP address assigned by the provider,
the CAT-32 IP connects to a special dynamic DNS server in regular intervals and registers its IP
address there. The administrator may contact this server as well and pick up the same IP
address belonging to his device.
Port number at which the CAT-32 IP’s HTTP server is listening. If left empty the default value
will be used.
Telnet port
Port number at which the CAT-32 IP’s Telnet server is listening. If left empty the default value
will be used.
The administrator has to register a CAT-32 IP that is supposed to take part in the service with
the Dynamic DNS Server and assign a certain hostname to it. He will get a nickname and a
password in return. This account information, together with the hostname, is needed in order to
determine the IP address of the registered CAT-32 IP.
Bandwidth limitation
The maximum network traffic generated through the CAT-32 IP’s Ethernet device. Value in
Kbit/s.
You have to perform the following steps in order to enable Dynamic DNS:
Enable Telnet access
Set this option to allow access to ARA express using the Telnet Gateway (see the Section
called Telnet Console)
ꢀ
ꢀ
ꢀ
Make sure that the LAN interface of the CAT-32 IP is properly configured.
Open the Dynamic DNS Settings configuration dialog
Enable Dynamic DNS and change the settings according to your needs (see the next page).
Disable Setup Protocol
Enable this option to exclude the CAT-32 IP from the setup protocol.
50
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Security
Enable Dynamic DNS
Enables the Dynamic DNS service. This requires a configured DNS server IP address.
Dynamic DNS server
This is the server name where the CAT-32 IP registers itself in regular intervals. At the time of
writing, this is a fixed setting since only dyndns.org is currently supported.
Force HTTPS
If this option is enabled, access to the web front-end is only possible using an HTTPS
connection. The CAT-32 IP will not listen on the HTTP port for incoming connections.
Hostname
This is the hostname of the CAT-32 IP that is provided by the Dynamic DNS Server. (Use the
whole name including the domain, e.g. testserver.dyndns.org not just the actual hostname).
KVM encryption
This option controls the encryption of the RFB protocol. RFB is used by the Remote Console to
transmit both the screen data to the administrator’s machine and the keyboard and mouse data
back to the host. If set to "Off" no encryption will be used. If set to "Try", the applet will attempt
to establish an encrypted connection. If connection establishment fails for any reason an
unencrypted connection will be used. If set to Force the applet tries to make an encrypted
connection. An error will be reported if connection establishment fails.
Username
You have registered this username during your manual registration with the Dynamic DNS
Server. Spaces are not allowed in the nickname.
Password
The password used during manual registration with the Dynamic DNS Server.
Check time
The CAT-32 IP registers itself in the Dynamic DNS server at this time.
Check interval
This is the interval for reporting again to the Dynamic DNS server by the CAT-32 IP.
Note: The KVM over IP module has its own independent real time clock. Make sure the time
setting is correct. (See the Section called Date and Time on page 59)
52
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Certificate
After completing these three steps, the CAT-32 IP has its own certificate that is used to identify
it to its clients.
Note: If you destroy the CSR on the KVM over IP module there is no way to get it back! In
case you deleted it by mistake, you have to repeat the three steps as described previously.
Common name
This is the network name of the CAT-32 IP once it is installed in the user's network It is identical
to the name that is used to access the CAT-32 IP with a web browser (without the “ http:// ”
prefix). In case the name given here and the actual network name differ, the browser will pop up
a security warning when the CAT-32 IP is accessed using HTTPS.
The CAT-32 IP uses the Secure Socket Layer (SSL) protocol for any encrypted network traffic
between itself and a connected client. During the connection establishment the CAT-32 IP has
to expose its identity to a client using a cryptographic certificate.
Organizational unit
This field is used for specifying to which department within an organization the CAT-32 IP
belongs.
This certificate and the underlying secret key is the same for all CAT-32 IP units and certainly
will not match the network configuration that will be applied to the CAT-32 IP by its user. The
certificate's underlying secret key is also used for securing the SSL handshake. Hence, this is a
security risk (but far better than no encryption at all).
Organization
The name of the organization to which the CAT-32 IP belongs.
Locality/City
The city where the organization is located.
However, it is possible to generate and install a new certificate that is unique for a particular
CAT-32 IP. In order to do this, the CAT-32 IP is able to generate a new cryptographic key and
the associated Certificate Signing Request (CSR) that needs to be certified by a certification
authority (CA). A certification authority verifies that you are the person you claim you are, and
signs and issues a SSL certificate to you.
State/Province
The state or province where the organization is located.
The following steps are necessary to create and install an SSL certificate for the CAT-32 IP:
Country (ISO code)
The country where the organization is located. This is the two-letter ISO code, e.g. DE for
Germany, or US for the USA.
1. Create an SSL Certificate Signing Request using the panel shown in the screen shot
above. You need to fill out a number of fields that are explained on the next page. Once
this is done, click on the Create button to initiate the Certificate Signing Request
generation. The CSR can be downloaded to your administration machine with the
Download CSR button (see the illustration on the next page).
2. Send the saved CSR to a CA for certification. You will get the new certificate from the CA
after a more or less complicated traditional authentication process (depending on the
CA).
Challenge Password
Some certification authorities require a challenge password to authorize later changes on the
certificate (e.g. revocation of the certificate). The minimal length of this password is 4
characters.
3. Upload the certificate to the CAT-32 IP switch using the Upload button.
54
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Serial Port
Confirm Challenge Password
Confirmation of the Challenge Password
Email
The email address of a contact person that is responsible for the CAT-32 IP and its security.
Key length
This is the length of the generated key in bits. 1024 bits are sufficient for most cases. Longer
keys may result in slower response time by the CAT-32 IP during connection establishment.
The CAT-32 IP Serial Settings allow you to specify what device is connected to the serial port
and how to use it.
Configuration or console login
Do not use the serial port for any special function; use it only for the initial configuration
Modem
The CAT-32 IP offers remote access using a telephone line in addition to the standard access
over the built-in Ethernet adapter. The modem needs to be connected to the serial interface of
the CAT-32 IP.
Connecting to the CAT-32 IP using a telephone line allows you to set up a dedicated point-to-
point connection from your console computer to the CAT-32 IP. In other words, the CAT-32 IP
acts as an Internet Service Provider (ISP) to which you can dial in. The connection is
established using the Point-to-Point Protocol (PPP). Before you connect to the CAT-32 IP,
make sure you configure your console computer accordingly. For instance, on Windows based
operating systems you can configure a dial-up network connection, which defaults to the right
settings like PPP.
The Modem Settings panel allows you to configure remote access to the CAT-32 IP using a
modem. The meaning of each parameter will be described below. The modem settings are part
of the serial settings panel.
56
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Date And Time
ꢀ
Serial line speed
The speed the CAT-32 IP is communicating with the modem. Most modems available today
will support the default value of 115200 bps. In case you are using an old modem and
discovering problems try to lower this speed.
ꢀ
Modem Init String
The initialization string used by the CAT-32 IP to initialize the modem. The default value will
work with all modern standard modems directly connected to a telephone line. In case you
have a special modem or the modem is connected to a local telephone switch that requires
a special dial sequence in order to establish a connection to the public telephone network,
you can change this setting by entering a new string. Refer to your modem’s manual about
the AT command syntax.
ꢀ
ꢀ
Modem server IP address
This IP address will be assigned to the CAT-32 IP during the PPP handshake. Since it is a
point-to-point IP connection virtually every IP address is possible but you must make sure, it
is not interfering with the IP settings of the CAT-32 IP and your console computer. The
default value will work in most cases.
Modem client IP address
This IP address will be assigned to your console computer during the PPP handshake.
Since it is a point-to-point IP connection virtually every IP address is possible but you must
make sure, it is not interfering with the IP settings of the CAT-32 IP switch and your console
computer. The default value will work in most cases.
Pass-through access to serial port via Telnet
Using this option, it is possible to connect an arbitrary device to the serial port and access it
(assuming it provides terminal support) via Telnet. Select the appropriate options for the serial
port and use the Telnet Console, or a standard Telnet client to connect to the CAT-32 IP.
Here you can set the internal real-time clock of the CAT-32 IP. You can adjust the clock
manually or use an NTP timeserver. Without a timeserver your time setting will be lost if the
CAT-32 IP is powered down for more than a few minutes. To avoid this, you can use an NTP
timeserver which sets up the internal clock automatically to the current UTC time. Because the
NTP server time is always UTC, there is a setting that allows you to set up a static offset to get
your local time.
Note: The KVM over IP module does not adjust to daylight saving time automatically. So you
have to set up the UTC offset according to the local conventions of your country.
58
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
SMTP Logging enabled
Event Log
With this option, the CAT-32 IP is able to send Emails to an address given by the Email address
text field in the Event Log Settings. These mails contain the same description strings as the
internal log file and the mail subject is filled with the event group of the occurred log event. In
order to use this log destination you have to specify an SMTP server that has to be reachable
from the CAT-32 IP and that needs no authentication at all (<serverip>:<port>).
SNMP Logging enabled
If this is activated, the CAT-32 IP sends an SNMP trap to a specified destination IP address
every time a log event occurs. If the receiver requires a community string, you can set it in the
appropriate text field. Most of the event traps only contain one descriptive string with all
information about the log event. Only authentication and host power events have a trap class
that consists of several fields with detailed information about the occurred event. To receive
these SNMP traps, any SNMP trap listener may be used.
Warning In contrast to the internal log file on the CAT-32 IP, the size of the NFS log file is not
limited. Every log event will be appended to the end of the file so it grows continuously, so you
may have to delete it or move it from time to time.
Important events like a login failure or a firmware update are logged to a selection of logging
destinations. Each of those events belongs to an event group, which can be activated
separately.
In the Event Log Settings you can choose how many log entries are shown on each page.
Furthermore, you can clear the log file here.
List logging enabled
The common way to log events is to use the internal log list of the CAT-32 IP. To show the log
list, click on Event Log on the Maintenance page.
Since the CAT-32 IP’s system memory is used to save all the information, the maximum number
of possible log list entries is restricted to 1000 events. Every entry that exceeds this limit
overrides the oldest one.
Note: If the reset button on the HTML front end is used to restart the KVM over IP module all
logging information is saved permanently and is available after the module has been started.
If the KVM over IP module loses power or a hard reset is performed, all logging data will be
lost. To avoid this, use one of the log methods described below.
NFS Logging enabled
Defines an NFS server to write all logging data to a file that is located there. To write logging
data from multiple CAT-32 IP units to only one NFS share, you have to define a file name that is
unique for each device. When you change the NFS settings and press Apply, the NFS share
will be mounted immediately. That means, the NFS share and the NFS server must be filled
with valid sources or you will get an error.
60
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
Event Log
5.7.6. Maintenance
Displays the log list including the events that are logged by the CAT-32 IP.
Device Information
This section contains a summary showing various information about the CAT-32 IP and its
current firmware. It also allows you to reset the unit.
Update Firmware
The CAT-32 IP is a complete standalone computer. The software it runs is called the firmware.
The firmware of the CAT-32 IP can be updated remotely in order to install new functionality or
special features.
View the data file for support
Allows you to download the CAT-32 IP data file with specific support information. This is an
XML file with certain customized support information like the serial number etc. You can send
this information if you contact LINDY technical support. It may help us solve any problems.
Connected Users
The example below displays the CAT-32 IP activity. From left to right the connected user(s), its
IP address (from which host the user comes from) and its activity status is displayed. RC means
that the Remote Console is open. If the Remote Console is opened in exclusive mode the term
(exclusive) is added. For more information about this option see the section called Remote
Console Control Bar.
To display the user activity, the
last column contains either the
term active for an active user
or 20 min idle for a user who
is inactive for a certain amount
of time.
62
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5
IP Access Configuration & Operation
Section 5
IP Access Configuration & Operation
New firmware updates are provided as a binary file which can be sent to you by email. Please
contact LINDY Technical Support team in your preferred country should you need to update
your firmware. Please note that an error during a firmware update may cause damage to the
unit, therefore a firmware update should only be performed if it is really necessary.
This section allows you to reset specific parts of the device. This involves the keyboard and
mouse, the video engine and the CAT-32 IP itself.
Updating the firmware is a four stage process:
1. The new firmware file is uploaded to the CAT-32 IP. In order to do this you need to select
the file on your local system using the Browse button on the Upload Firmware panel. Once
the firmware file has been uploaded it is checked whether it is a valid firmware file and
whether there were any transmission errors. In case of any error the Upload Firmware
function will be aborted.
2. If everything went well you will see the Update Firmware panel. The panel shows you the
version number of the currently running firmware and the version number of the uploaded
firmware. Pressing the Update button will replace the old version with the new one.
3. After the firmware has been stored, the CAT-32 IP will automatically reset itself. Half a
minute after the reset the CAT-32 IP will run with the new firmware version and should be
accessible. However, you will be required to login once again.
4. Once you have logged in we recommend you delete the Temporary Internet Files from
your browser to ensure that the appearance of the web interface is correct. To do this in
Internet Explorer, select:
Tools > Internet Options > General > Delete Files
Tick the check box: Delete all offline content, and click OK
Note: The firmware update process and consistency check means that making a mistake
when updating the firmware is very unlikely. However, we recommend only experienced
users or administrators should perform the firmware update. This process is not reversible
and may take some minutes. Make sure the Cat-32 IP’s power supply will not be interrupted
during the update process!
Resetting the unit itself is mainly needed to activate a newly updated firmware. It will close all
current connections to the administration console and to the Remote Console.
The whole process will take about half a minute. Resetting sub devices (e.g. the video engine)
will take a few seconds only and does not result in connections closing. To reset individual CAT-
32 IP functionality, click on the Reset button.
Tip: Should your keyboard fail to operate correctly, in the remote console, after a firmware
update please use the Reset Keyboard/Mouse option in the Maintenance section.
Note: Only the super user is allowed to reset the CAT-32 IP.
Unit Reset
64
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
7. Special key combinations, e.g. ALT+F2, ALT+F3 are intercepted by the console
system and not transmitted to the host.
You have to define a so-called Button Key. This can be done in the Remote Console
settings.
Troubleshooting
KVM Switch Troubleshooting
8. In the browser the CAT-32 IP switch pages are inconsistent.
Clear Temporary Internet Files from your browser. To do this in Internet Explorer, select:
If none of the port LEDs or the display on the KVM Switch are illuminated then please check
that the power adapter is connected and switched on at the mains.
Tools > Internet Options > General > Delete Files
Before you check any further please make sure that all cables are fitted correctly!
Tick the check box: Delete all offline content, and click OK
1. If the problem is also is visible from the local console please first refer to section 3.4
Troubleshooting.
9. Windows XP doesn’t wake from standby mode
This could be a Windows XP problem. Try not to move the mouse while XP goes into
standby mode.
2. Please check if the currently selected computer is in sleep mode or powered down.
10.Every time I open a dialog box with some buttons, the mouse pointers are not
synchronised anymore
3. If the Monitor picture is not sharp or shows shadows: Please check the quality of the UTP
cable between KVM switch and Computer Access Module. Try replacing the cable, or use a
higher quality cable.
Please check if you have an option like ‘Automatically move mouse pointer to the default
button of dialog Unites’ enabled in the mouse settings of the operating system. This option
needs to be disabled.
4. If you have forgotten a Password please contact LINDY.
IP Access Troubleshooting
1. The remote mouse doesn’t work or is not synchronized
Make sure the mouse settings in CAT-32 IP match the mouse model. Use the Intelligent
Sync option from the Mouse Handling sub menu of the Remote Console Options menu.
2. The remote mouse does not work correctly
Try using the Reset Keyboard/Mouse option in the Maintenance section.
3. The video quality is bad or the picture is grainy
Try to correct the brightness and contrast settings until they are out of a range where the
picture looks grainy. Use the auto adjustment feature to correct a flickering video.
4. Login on CAT-32 IP switch fails.
Was the correct combination of user and password given? The default user name is super
and the password is pass. Furthermore, your browser must be configured to accept cookies.
5. The Remote Console window can’t connect to the CAT-32 IP.
Possibly a firewall prevents access to the Remote Console. Make sure the TCP port
numbers 443 or 80 are open for incoming TCP connections. Install the latest version of Java
Virtual Machine.
6. No connection can be established to the CAT-32 IP.
Check whether the network connection is working in general (ping the IP address of CAT-32
IP). If not, check the network hardware. Is the CAT-32 IP powered on? Check whether the IP
address of CAT-32 IP switch and all other IP related settings are correct! Also verify that all
the IP infrastructure of your LAN, including routers etc., is correctly configured.
66
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
Technical Information
The layout for this keyboard is also shown. However, most modifier keys and other
alphanumeric keys used for hotkey purposes in application programs are in an identical
position, no matter what language mapping you are using. Some of the keys have aliases also;
they can be named by 2 key codes (separated by a comma in the previous table).
0 - 9
A - Z
, TILDE
-, MINUS
=, EQUALS
;
’
<, LESS
,
.
/, SLASH
BACK SPACE
TAB
[
Key Codes
This table shows the key codes used to
defines keystrokes or hotkeys for
several functions. Please note that these
key codes do not necessarily represent
key characters that are used on
international keyboards. They name a
key on a standard 104 key PC keyboard
with US English language mapping.
]
ENTER
CAPS LOCK
\, BACK SLASH
LSHIFT, SHIFT
RCTRL
RSHIFT
LCTRL, CTRL
LALT, ALT
SPACE
ALTGR
ESCAPE, ESC
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
PRINTSCREEN
SCROLL LOCK
BREAK
INSERT
HOME
PAGE UP
DELETE
END
PAGE DOWN
UP
LEFT
DOWN
RIGHT
NUM LOCK
NUMPAD0
NUMPAD1
NUMPAD2
NUMPAD3
NUMPAD4
NUMPAD5
NUMPAD6
NUMPAD7
NUMPAD8
NUMPAD9
NUMPADPLUS,NUMPAD PLUS
NUMPAD/
NUMPADMUL,NUMPAD MUL
NUMPADMINUS,NUMPAD MINUS
NUMPADENTER
WINDOWS
MENU
68
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
Certifications, Recycling Information
WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products
Video Modes
United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment.
It is no longer allowed to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.
The table below lists the video modes that the CAT-32 IP remote console supports. Please do
not use any other custom video settings; the CAT-32 IP may not be able to detect them.
Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways. Please follow your
national law when you want to dispose of any electrical or electronic products.
More details can be obtained from your national WEEE recycling agency.
Resolution (x, y)
640 x 350
640 x 400
640 x 480
720 x 400
Refresh Rates (Hz)
70, 85
56, 70, 85
60, 67, 72, 75, 85, 90, 100, 120
Germany / Deutschland
Die Europäische Union hat mit der WEEE Direktive umfassende Regelungen für die Verschrottung und das Recycling von Elektro- und
Elektronikprodukten geschaffen. Diese wurden von der Bundesregierung im Elektro- und Elektronikgerätegesetz – ElektroG in deutsches
Recht umgesetzt.
Dieses Gesetz verbietet vom 24.März 2006 an das Entsorgen von entsprechenden, auch alten, Elektro- und Elektronikgeräten über die
Hausmülltonne! B2B Geräte wie diese KVM Switches nimmt LINDY kostenlos zurück und führt sie einem geordneten Recycling zu. Bitte
nehmen Sie hierzu Kontakt mit LINDY auf, die Adressen finden Sie auf der LINDY Website www.lindy.com
70, 85
800 x 600
832 x 624
56, 60, 70, 72, 75, 85, 90, 100
75
1024 x 768
1152 x 864
1152 x 870
1152 x 900
1280 x 960
1280 x 1024
60, 70, 72, 75, 85, 90, 100
75
75
66
60
60, 75
France
En 2006, l'union Européenne
électronique.
a
introduit la nouvelle réglementation (DEEE) pour le recyclage de tout équipement électrique et
Chaque Etat membre de l’ Union Européenne a mis en application la nouvelle réglementation WEEE de manières légèrement différentes.
Veuillez suivre le décret d’application correspondant à l’élimination des déchets électriques ou électroniques de votre pays.
Italy
Nel 2006 l’unione europea ha introdotto regolamentazioni (WEEE) per la raccolta e il riciclo di apparecchi elettrici ed elettronici. Non è più
consentito semplicemente gettare queste apparecchiature, devono essere riciclate.
Ogni stato membro dell’ EU ha tramutato le direttive WEEE in leggi statali in varie misure. Fare riferimento alle leggi del proprio Stato
quando si dispone di un apparecchio elettrico o elettronico.
Higher resolutions than 1280 x 1024, i.e. 1600x1200 may be displayed in virtual desktop mode
with a moving visible area of 1280 x 1024.
Per ulteriori dettagli fare riferimento alla direttiva WEEE sul riciclaggio del proprio Stato.
CE Statement
This device complies with the European Regulations for Electromagnetic Compatibility (EMC) of the European Union and it is equipped with
the CE mark. This unit has to be used with high quality shielded connection cables. Only if these high quality shielded cables are used can
it be sure that the EMC compatibility is not adversely influenced.
FCC Statement
Shielded cables must be used with this equipment to maintain compliance with radio frequency energy emission regulations and ensure a
suitably high level of immunity to electromagnetic disturbances.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at their own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.
71
70
Download from Www.Somanuals.com. All Manuals Search And Download.
|
LG Electronics Flat Panel Television 22LB4510 User Manual
Lincoln Electric Welder SVM194 A User Manual
Logitech Computer Keyboard Tab4 101 User Manual
Lowrance electronic Fish Finder ELITE 4HDI User Manual
LST Smoke Alarm HT 11001 User Manual
Manhattan Computer Products Computer Hardware 160391 User Manual
Maytag Microwave Oven MMV5207AA User Manual
McCulloch Brush Cutter B40B Elite User Manual
Memorex Computer Drive Travel Drive User Manual
Metrologic Instruments Scanner Laser Scanner User Manual