Regulatory notes and statements
Wireless LAN, Health and Authorization for use
Radio frequency electromagnetic energy is emitted from Wireless LAN devices.
The energy levels of these emissions however are far much less than the
electromagnetic energy emissions from wireless devices like for example mobile
phones. Wireless LAN devices are safe for use frequency safety standards and
recommendations. The use of Wireless LAN devices may be restricted in some
situations or environments for example:
108Mbps Super-GTM
Wireless LAN Router
·On board of airplanes, or
·In an explosive environment, or
·In case the interference risk to other devices or services is perceived or identified
as harmful
In case the policy regarding the use of Wireless LAN devices in specific
organizations or environments (e.g. airports, hospitals, chemical/oil/gas industrial
plants, private buildings etc.) is not clear, please ask for authorization to use these
devices prior to operating the equipment.
Regulatory Information/disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with
the instructions included in the user documentation provided with the product. Any
changes or modifications made to this device that are not expressly approved by the
manufacturer may void the user’s authority to operate the equipment. The
Manufacturer is not responsible for any radio or television interference caused by
unauthorized modification of this device, of the substitution or attachment.
Manufacturer and its authorized resellers or distributors will assume no liability for
any damage or violation of government regulations arising from failing to comply
with these guidelines.
User’s Manual
USA-FCC (Federal Communications Commission) statement
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of this device.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Dynamic.......................................................................................................................................................................................... 34
Routing Table.................................................................................................................................................................................. 34
Access................................................................................................................................................................................................. 35
Filters .............................................................................................................................................................................................. 35
Virtual Server.................................................................................................................................................................................. 41
Special AP....................................................................................................................................................................................... 42
DMZ................................................................................................................................................................................................ 43
Firewall Rule................................................................................................................................................................................... 44
Management........................................................................................................................................................................................ 45
SNMP.............................................................................................................................................................................................. 45
This screen enables you to configure the SNMP. ........................................................................................................................... 45
Remote Management ...................................................................................................................................................................... 46
Tools ................................................................................................................................................................................................... 47
Reset................................................................................................................................................................................................ 47
TABLE OF CONTENT
ABOUT THIS GUIDE .................................................................................... 1
Purpose.................................................................................................................................................................................................. 1
Terms/Usage ......................................................................................................................................................................................... 1
Overview of this User’s Guide.............................................................................................................................................................. 1
INTRODUCTION ........................................................................................... 2
Applications:......................................................................................................................................................................................... 2
Features:................................................................................................................................................................................................ 3
UNPACKING AND SETUP.............................................................................. 4
Unpacking............................................................................................................................................................................................. 4
Setup ..................................................................................................................................................................................................... 4
HARDWARE INSTALLATION......................................................................... 5
TECHNICAL SPECIFICATIONS ................................................................... 49
Front Panel............................................................................................................................................................................................ 5
Rear Panel............................................................................................................................................................................................. 6
Hardware connections........................................................................................................................................................................... 7
Connecting the WLAN Router.......................................................................................................................................................... 7
Check the installation........................................................................................................................................................................ 7
PC NETWORK TCP/IP SETTING ................................................................. 8
Windows 95/98/ME.............................................................................................................................................................................. 8
Windows 2000 ...................................................................................................................................................................................... 9
Windows XP....................................................................................................................................................................................... 10
CONFIGURATION....................................................................................... 11
Login to the WLAN Router through Wireless LAN........................................................................................................................... 11
Login to the WLAN Router ................................................................................................................................................................ 11
Using the Web Browser...................................................................................................................................................................... 11
Setup Wizard....................................................................................................................................................................................... 12
Advanced configuration...................................................................................................................................................................... 21
LAN Setting........................................................................................................................................................................................ 21
LAN & DHCP Server ..................................................................................................................................................................... 21
WAN............................................................................................................................................................................................... 22
Password ......................................................................................................................................................................................... 23
Time................................................................................................................................................................................................ 23
Dynamic DNS................................................................................................................................................................................. 24
Wireless .............................................................................................................................................................................................. 25
Basic................................................................................................................................................................................................ 25
Authentication................................................................................................................................................................................. 26
Advanced ........................................................................................................................................................................................ 28
Status................................................................................................................................................................................................... 29
Device Information ......................................................................................................................................................................... 29
Log.................................................................................................................................................................................................. 30
Log Setting...................................................................................................................................................................................... 31
Statistic............................................................................................................................................................................................ 32
Wireless........................................................................................................................................................................................... 32
Routing................................................................................................................................................................................................ 33
Static ............................................................................................................................................................................................... 33
iv
v
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THIS GUIDE
INTRODUCTION
Congratulations on your purchase of this 108Mbps Super-GTM Wireless LAN
Router. This integrated access device combines Internet gateway functions with
wireless LAN and Fast Ethernet switch. It provides a complete solution for Internet
surfing and office resources sharing, and it is easy to configure and operate for
every users.
With the explosive growth of the Internet, accessing information and services at
any time, day or night has become a standard requirement for most people. The era
of the standalone PC is waning. Networking technology is moving out of the
exclusive domain of corporations and into homes with at least two computers.
This integrated access device combines Internet gateway functions with wireless
LAN and Fast Ethernet switch. Designed for the business and home, it saves you
the cost of installing a separate modem and ISP line for each computer, while
providing ready connection for the users, with or without the network wires.
Broadband network access is also gaining ground. However, allowing more than
two computers to access the Internet at the same time means less affordable, higher
costs. Thus, there is a need to share one legal IP address over a single Internet
connection to link the home with the Internet.
Purpose
This manual discusses how to install the 108Mbps Super-GTM Wireless LAN
Router.
Terms/Usage
In this guide, the term “the WLAN Router” refers to your 108Mbps Super-GTM
Wireless LAN Router.
The scarcity of IP addresses and using a shared Internet connection through an
Internet sharing device can solve high network access costs. All linked computers
can make full use of broadband capabilities over such a device.
This device not only comes equipped with a wide range of features, but also can be
installed and configured right out of the box. This device supports a simple local
area network and Internet access share, offering great cost savings.
The local area network connects up home computers while also allowing any of the
computers to access the Internet, share resources, or play online games—the basis
of the family computing lifestyle.
Overview of this User’s Guide
Introduction. Describes the 108Mbps Super-GTM Wireless LAN Router and its
features.
Unpacking and Setup. Helps you get started with the basic installation of the
108Mbps Super-GTM Wireless LAN Router.
Identifying External Components. Describes the front panel, rear panel and LED
indicators of the 108Mbps Super-GTM Wireless LAN Router.
Connecting the Router. Tells how you can connect the 108Mbps Super-GTM
Wireless LAN Router to your xDSL/Cable Modem.
Applications:
Broadband Internet access:
Several computers can share one high-speed broadband connection through
wireless or wired (WLAN, LAN and WAN-Internet).
Resource sharing:
Share resources such as printers, scanners and other peripherals.
Technical Specifications. Lists the technical (general, physical and environmental,
performance and Routers settings) specifications of the 108Mbps Super-GTM
Wireless LAN Router.
File sharing:
Exchange data, messages, and distribute files thus making good use of hard disk
space.
Online gaming:
Through the local area network, online gaming and e-commerce services can be
easily setup.
Firewall:
A built-in firewall function — for security and anti-hack system.
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING AND SETUP
Features:
This chapter provides unpacking and setup information for the 108Mbps Super-GTM
Wireless LAN Router.
‹ High speed data transfer rate
‹ Supports NAT for share 1 IP address to all LAN/WLAN users.
‹ Supports PPPoE and PPTP protocol for Dial-Up ADSL.
‹ Supports 64/128 bit WEP Encryption
‹ Supports WPA-PSK, WPA2-PSK, WPA, WPA2 security
‹ Supports DHCP Server / Client.
‹ Supports UPnP (Universal Plug and Play).
‹ Supports Virtual Server mapping.
‹ Supports Packet filtering.
Unpacking
Open the box of the WLAN Router and carefully unpack it. The box should contain
the following items:
©
©
©
©
One 108Mbps Super-GTM Wireless LAN Router
One dipole antenna
One external power adapter
One CD-ROM with this User’s Guide
‹ Supports Protocol filtering
‹ Support Domain filtering
‹ Supports DNS
If any item is found missing or damaged, please contact your local reseller for
replacement.
‹ Simple Firewall protection.
Setup
‹ Upgradeable firmware for future function.
‹ Simple setting using Setup Wizard.
‹ Easy configuration via WEB Browser.
The setup of the WLAN Router can be performed properly using the following
methods:
©
The power outlet should be within 1.82 meters (6 feet) of the Broadband Router.
©
Visually inspect the DC power jack and make sure that it is fully secured to the
power adapter.
©
©
Make sure that there is proper heat dissipation from and adequate ventilation
around the Broadband Router. Do not place heavy objects on the Broadband
Router.
Fix the direction of the antennas. Try to place the Wireless Router in a position
that can best cover your wireless network. Normally, the higher you place the
antenna, the better the performance will be. The antenna’s position enhances the
receiving sensitivity.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE INSTALLATION
Rear Panel
The figure below shows the rear panel of the 108Mbps Super-GTM Wireless LAN
Router.
Front Panel
The figure below shows the front panel of the 108Mbps Super-GTM Wireless LAN
Router.
Rear Panel
Front Panel
Antenna
There is one 2dBi Gain Antenna in the rear panel for wireless connection.
Power
This indicator lights green when the hub is receives power, otherwise it is off.
LAN (1-4)
Four RJ-45 10/100Mbps Auto-MDIX ports for connecting to either 10Mbps or
100Mbps Ethernet connections.
Status
This indicator blinking green means the WLAN Router is working successful.
Otherwise, this indicator always on or off means the function of the WLAN Router
is fail.
WAN
In the four port broadband router, there is an RJ-45 10/100Mbps Auto-MDIX port
for the WAN that will fit the xDSL/Cable modem’s specification need.
WAN (Link/ACT)
The indicators light green when the WAN port was connected to an xDSL/Cable
modem successfully.
The indicators blink green while the WAN port was transmitting or receiving data
on the xDSL/Cable modem.
DC IN
Plug the power adapter to this power jack
RESET
Use a pin-shape item to push to reset this device to factory default settings. It will
be useful too when the manager forgot the password to login, but the setting will be
back to default setting.
WLAN (ACT)
This indicator lights green when there are wireless devices connected and
transmitting data to the WLAN Router.
Local Network (Link/ACT)
These indicators light green when the LAN ports were connected successfully.
These indicators blinking green while the LAN ports were accessing data.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PC NETWORK TCP/IP SETTING
Hardware connections
Connecting the WLAN Router
The network TCP/IP settings differ based on the computer’s operating system
(Win95/98/ME/NT/2000/XP) and are as follows.
Windows 95/98/ME
1. Click on the “Network neighborhood” icon found on the desktop.
2. Click the right mouse button and a context menu will be show.
3. Select “Properties” to enter the TCP/IP setting screen.
4. Select “Obtain an IP address automatically” on the “IP address” field.
1. Plug in one end of the network cable to the WAN port of the WLAN Router.
2. Plug in the other end of the network cable to the Ethernet port of the xDSL or
Cable modem.
3. Use another network cable to connect to the Ethernet card on the computer
system; the other end of the cable connects to the LAN port of the WLAN
Router. Since the 108Mbps Super-GTM Wireless LAN Router has four ports, you
can connect up to four computers directly to the unit. There you do not have to
buy a switch to connect these computers since one WLAN Router functions both
as a connection-sharing unit and as a switch.
5. Select “Disable DNS” in the “DNS” field.
Check the installation
The control LEDs of the WLAN Router are clearly visible and the status of the
network link can be seen instantly:
1. With the power source on, once the device is connected to the broadband modem,
the Power, System, LAN, WLAN and WAN port LEDs of the WLAN Router
will light up indicating a normal status.
2. While the WAN is link up to the ADSL/Cable modem, the WAN port’s LED
will light up.
3. While the LAN is link up to the computer system, the LAN port’s LED will light
up.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Select “None” for the “Gateway address” field.
Windows XP
Point the cursor and click the right button on the “My Network Place” icon.
Select “properties” to enter the TCP/IP setting window.
1. Set “IP address” to “Obtain an IP address automatically.”
2. Set “DNS” to “Obtain DNS server address automatically.”
Windows 2000
Double click on the “My computer” icon on the desktop. When “My computer”
window opens, open the “Control panel” and then open the “Network dialup
connection” applet. Double click on the “Local area network connection” icon.
Select “Properties” to enter the TCP/IP setting window.
1. In the “Local area network status” window, click on “Properties.”
2. In the “Local area network connection” window, first select TCP/IP setting
and then select “Properties.”
3. Set both “IP address” and “DNS” to Automatic configuration.
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURATION
Setup Wizard
Setup wizard is provided as the part of the web configuration utility. User can
simply follow the step-by-step process to get the wireless router configuration
ready to run in 6 easy steps by clicking on the “Wizard” button on the function
menu. The following screen will appear. Please click “Next” to continue.
First make sure that the network connections are functioning normally.
This WLAN Router can be configured using Internet Explorer 5.0 or newer web
browser versions.
Login to the WLAN Router through Wireless LAN
Before configuring the WLAN Router through WLAN, make sure that the SSID,
Channel and the WEP is set properly.
The default setting of the WLAN Router that you will use:
V SSID: default
V Channel: 6
V Security: disable
Login to the WLAN Router
Before you configure this device, note that when the WLAN Router, make sure the
host PC must be set on the IP subnetwork that can be accessed by the xDSL/Cable
modem. For example, when the default network address of the xDSL/Cable modem
Ethernet interface is 192.168.1.x, then the host PC should be set at 192.168.1.xxx
(where xxx is a number between 2 and 254), and the default subnet mask is
255.255.255.0.
Step 1: Set up new Password
User can change the password and then click “Next” to continue.
Using the Web Browser
1. Open Internet Explorer 5.0 or above Internet browser.
the URL web address location.
3. When the following dialog box appears, enter the user name and password to
login to the main configuration window, the default username and password is
“admin”.
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Choose time zone
Step 4: Set Internet connection
Select the time zone from the drop down list. Please click “Next” to continue.
Select how the router will set up the Internet connection: Obtained IP automatically;
Fixed IP address; PPPoE to obtain IP automatically; PPPoE with a fixed IP address;
PPTP.
Obtain IP automatically (DHCP client):
If user has enabled DHCP server, choose "Obtain IP automatically (DHCP client)"
to have the WLAN Router assign IP addresses automatically.
Step 3: Set LAN connection and DHCP server
Set user’s IP address and mask. The default IP is 192.168.1.1. If user likes to enable
DHCP, please click “Enabled”. DHCP enabled is able to automatically assign IP
addresses. Please assign the range of IP addresses in the fields of “Range start” and
“Range end”. Please click “Next” to continue.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Fixed IP Address:
PPPoE to obtain IP automatically:
If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will
provide a Password and User Name, and then the ISP uses PPPoE. Choose this
option and enter the required information.
If the Internet Service Providers assign a fixed IP address, choose this option and
enter the assigned IP address, subnet mask, gateway IP and DNS IP addresses for
the WLAN Router.
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
PPPoE with a fixed IP address:
PPTP:
If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will
provide a Password, User Name and a Fixed IP Address, choose this option and
enter the required information.
If connected to the Internet using a (PPTP) xDSL Modem, enter the your IP
Address, Subnet Mask, Gateway, Server IP, PPTP Account and PPTP Password,
Your Subnet Mask required by your ISP in the appropriate fields. If your ISP has
provided you with a Connection ID, enter it in the Connection ID field, otherwise,
leave it zero.
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5: Set Wireless LAN connection
L2TP:
Click “Enable” to enable wireless LAN. If user enables the wireless LAN, type the
SSID in the text box and select a communications channel. The SSID and channel
must be the same as wireless devices attempting communication to the router.
If connected to the Internet using a L2TP (Dial-up xDSL) Modem, the ISP will
provide a Server IP. Account and Password. Choose this option and enter the
required information.
Step 6: Setup completed
The Setup wizard is now completed. The new settings will be effective after the
Wireless router restarted. Please click “Restart” to reboot the router. If user does
not want to make any changes, please click “Exit” to quit without any changes.
User also can go back to modify the setting by clicking “Back”.
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Start IP: Type an IP address to serve as the start of the IP range that DHCP will
Advanced configuration
LAN Setting
The screen enables user to configure the LAN & DHCP Server, set WAN
parameters, create Administrator and User passwords, and set the local time, time
zone, and dynamic DNS.
use to assign IP addresses to all LAN devices connected to the router.
End IP: Type an IP address to serve as the end of the IP range that DHCP will use
to assign IP addresses to all LAN devices connected to the router.
Domain Name: Type the local domain name of the network in the text box. This
item is optional.
WAN
LAN & DHCP Server
This screen enables user to set up the router WAN connection, specify the IP
address for the WAN, add DNS numbers, and enter the MAC address.
This page leads to set LAN and DHCP properties, such as the host name, IP address,
subnet mask, and domain name. LAN and DHCP profiles are listed in the DHCP
table at the bottom of the screen.
Connection Type: Select the connection type, either DHCP client, Fixed IP,
PPPoE, PPTP or L2TP from the drop-down list.
WAN IP: Select whether user wants to specify an IP address manually, or want
DHCP to obtain an IP address automatically. When Specify IP is selected, type the
IP address, subnet mask, and default gateway in the text boxes. User’s ISP will
provide with this information.
DNS 1/2/3: Type up to three DNS numbers in the text boxes. User’s ISP will
provide with this information.
Host Name: Type the host name in the text box. The host name is required by
some ISPs. The default host name is "AP-Router."
IP Address: This is the IP address of the router. The default IP address is
192.168.1.1.
Subnet Mask: Type the subnet mask for the router in the text box. The default
subnet mask is 255.255.255.0.
MAC Address: If required by user’s ISP, type the MAC address of the router
WAN interface in this field.
DHCP Server: Enables the DHCP server to allow the router to automatically
assign IP addresses to devices connecting to the LAN. DHCP is enabled by default.
All DHCP client computers are listed in the table at the bottom of the screen,
providing the host name, IP address, and MAC address of the client.
21
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Local Time: Displays the local time and date.
Time Zone: Select the time zone from the drop-down list.
Password
This screen enables user to set administrative and user passwords. These passwords
are used to gain access to the router interface.
Synchronize the clock with: Select the clock adjustment method form the drop-
down list.
Automatic: Automatically adjust the system time from NTP Server.
Manual: Manually adjust the system time when you press the Set Time button.
Default NTP server: The Simple Network Time Protocol (SNTP) server allows
the WLAN Router to synchronize the system clock to the global Internet through
the SNTP Server. Specify the NTP domain name or IP address in the text box.
Set the time: Manually setting the WLAN Router system time, press the Set Time
button to update the system time.
Daylight Saving: Enables user to enable or disable daylight saving time. When
enabled, select the start and end date for daylight saving time.
Dynamic DNS
Administrator: Type the password the Administrator will use to log in to the
system. The password must be typed again for confirmation. The authority if
Administrator allow user configuration of the WLAN Router.
User: Type the password the User will use to log in to the system. The password
must be typed again for confirmation. The authority if User only allow user viewing
current configuration of the WLAN Router.
This allows the DDNS server what your current IP address is when you are on-line.
You firstly need to register your preferred DNS on the DDNS providers. Then,
please select the DDNS address in the Server Address and fill the related
information in the below fields: Host Name, User Name and Password.
Time
This screen enables user to set the time and date for the router's real-time clock,
select properly time zone, and enable or disable daylight saving.
23
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Authentication
Wireless
The authentication type default is set to disable. There are four options: Disable,
WEP, WPA, and WPA2.
This section enables user to configuration the wireless communications parameters
for the WLAN Router.
Basic
This page allow user to enable and disable the wireless LAN function, create a
SSID, and select the channel for wireless communications.
Authentication Type: The authentication type default is set to open system.
There are three options: Open System; Shared Key, WPA and WPA-PKS.
WEP Encryption
Enable/Disable: Enables and disables wireless LAN via the WLAN Router.
SSID: Type an SSID in the text box. The SSID of any wireless device must match
the SSID typed here in order for the wireless device to access the LAN and WAN
via the router.
Channel: Select a transmission channel for wireless communications. The channel
of any wireless device must match the channel selected here in order for the
wireless device to access the LAN and WAN via the router.
Super G mode: From the drop list, if you like to use Super-GTM to enhance the
speed, there are three options on Super-GTM mode: Super G without turbo; Super G
with Dynamic turbo and Super G with Static turbo. The turbo mode indicates the
combination of two channels to enhance the throughput. Super G without turbo
indicates that it is on Super G mode without the channel’s combination. Dynamic
turbo is able to automatically detect if any ‘Super-GTM based’ product is available.
If no, the connection is via ‘normal’ G. Static turbo means it will not go back to
‘normal’ G once it starts.
WEP: Open System allows public access to the router via wireless
communications; Shared Key requires the user to set a WEP key to exchange data
with other wireless clients that have the same WEP key..
Extended Range Mode: Enable and disable wireless LAN via router.
Mode: Select the key mode in ASCII or HEX
WEP Key: Select the level of encryption from the drop-down list. The router
supports, 64- and 128-bit encryption.
SSID Broadcast: While SSID Broadcast is enabled, all wireless clients will be able
to communicate with the WLAN Router. For secure purpose, user may want to
disable SSID broadcast to allow only those wireless clients with the SSID to
communicate with the WLAN Router.
25
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Key 1 ~ Key 4: Enables user to create an encryption scheme for Wireless LAN
transmissions. Manually enter a set of values for each key. Select a key to use by
clicking the radio button next to the key. Click “Clear” to erase key values.
Advanced
This screen enables user to configure advanced wireless functions.
WPA/WPA2 Security
If WPA or WPA2 is selected, the below screen is shown. Please set the length of
the encryption key and the parameters for the RADIUS server.
Lifetime: Select the Lifetime of the Encryption Key from 5 Minutes to 1 Day. As
soon as the lifetime of the Encryption Key is over, the Encryption Key will be
renewed by the Radius server.
Beacon Interval: Type the beacon interval in the text box. User can specify a value
from 1 to 1000. The default beacon interval is 100.
RTS Threshold: Type the RTS (Request-To-Send) threshold in the text box. This
value stabilizes data flow. If data flow is irregular, choose values between 256 and
2346 until data flow is normalized.
Encryption Key: Select the Encryption Key Length Size ranging from 64 to 128
Bits that you would like to use.
Fragmentation Threshold: Type the fragmentation threshold in the text box. If
packet transfer error rates are high, choose values between 256 and 2346 until
packet transfer rates are minimized. (NOTE: set this fragmentation threshold value
may diminish system performance.)
DTIM Interval: Type a DTIM (Delivery Traffic Indication Message) interval in
the text box. User can specify a value between 1 and 65535. The default value is 1.
TX Rates (Mbps): Select one of the wireless communications transfer rates,
measured in megabytes per second, based upon the speed of wireless adapters
connected to the WLAN.
RADIUS Server:
1. Enter the IP address, Port used and Shared Secret by the Primary Radius
Server.
2. Enter the IP address, Port used and Shared Secret by the Secondary Radius
Server.
WPA-PSK/WPA2-PSK Security
If WPA-PSK or WPA2-PSK is selected, please set the PSK key in the pass phrase
field. The length should be 8 characters at least.
11g only mode: If selected the Enable, only allow 802.11g WLAN client
communicate with this WLAN Router.
Antenna Transmit Power: Adjust the power of the antenna transmission by
selecting from the dropping list for full, half (-3dB), quarter (-6dB), eighth (-9dB)
or min.
27
28
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN: This section displays the WAN interface configuration including the MAC
address, Connection status, DHCP client status, IP address, Subnet mask, Default
gateway, and DNS.
Click “DHCP Release” to release all IP addresses assigned to client stations
connected to the WAN via the router. Click “DHCP Renew” to reassign IP
addresses to client stations connected to the WAN.
Status
This selection enables user to view the status of the router LAN, WAN and
Wireless connections, and view logs and statistics pertaining to connections and
packet transfers.
Device Information
This screen enables user to view the router LAN, Wireless and WAN configuration.
Log
This screen enables user to view a running log of router system statistics, events,
and activities. The log displays up to 200 entries. Older entries are overwritten by
new entries. The Log screen commands are as follows:
Click “First Page” to view the first page of the log
Click “Last Page” to view the final page of the log
Click “Previous Page” to view the page just before the current page
Click “Next Page” to view the page just after the current page
Click “Clear Log” to delete the contents of the log and begin a new log
Click “Refresh” to renew log statistics
Firmware Version: Displays the latest build of the router firmware interface. After
updating the firmware in Tools - Firmware, check this to ensure that the firmware
was successfully updated.
LAN: This section displays the LAN interface configuration including the MAC
address, IP address, subnet mask, and DHCP server status. Click “DHCP Table” to
view a list of client stations currently connected to the router LAN interface.
Time: Displays the time and date that the log entry was created.
Message: Displays summary information about the log entry.
Source: Displays the source of the communication.
Destination: Displays the destination of the communication.
Note: Displays the IP address of the communication
Wireless: This section displays the wireless configuration information, including
the MAC address, the Connection status, SSID, Channel and Authentication type.
29
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Log Setting
Statistic
This screen enables user to set router logging parameters.
This screen displays a table that shows the rate of packet transmission via the router
LAN, Wireless and WAN ports (in bytes per second).
Click “Reset” to erase all statistics and begin logging statistics again.
SMTP Server: Type the SMTP server address for the email that the log will be
sent to in the next field.
Wireless
Send to: Type an email address for the log to be sent to. Click “Email Log Now” to
immediately send the current log.
This screen enables user to view information about wireless devices that are
connected to the WLAN Router.
Syslog Server: Type the IP address of the Syslog Server if user wants the router to
listen and receive incoming Syslog messages.
Log Type: Enables user to select what items will be included in the log:
System Activity: Displays information related to router operation.
Debug Information: Displays information related to errors and system
malfunction.
Attacks: Displays information about any malicious activity on the network.
Dropped Packets: Displays information about packets that have not been
transferred successfully.
Notice: Displays important notices by the system administrator.
Connected Time: Displays how long the wireless device has been connected to the
LAN via the router.
MAC Address: Displays the devices wireless LAN interface MAC address.
31
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Dynamic
Routing
This screen enables user to set NAT parameters.
This selection enables user to set how the router forwards data: Static and Dynamic.
Routing Table enables user to view the information created by the router that
displays the network interconnection topology.
Static
It enables user to set parameters by which the router forwards data to its destination
if user’s network has a static IP address.
NAT: Click the radio buttons to enable or disable the NAT function.
Transmit: Click the radio buttons to set the desired transmit parameters, disabled,
RIP 1, or RIP 2.
Receive: Click the radio buttons to set the desired transmit parameters, disabled,
RIP 1, or RIP 2.
Routing Table
This screen enables user to view the routing table for the router. The routing table is
a database created by the router that displays the network interconnection topology.
Network Address: Type the static IP address user’s network uses to access the
Internet. User’s ISP or network administrator provides user with this information.
Network Mask: Type the network (subnet) mask for user’s network. If user does
not type a value here, the network mask defaults to 255.255.255.255. User’s ISP or
network administrator provides user with this information.
Gateway Address: Type the gateway address for network. User’s ISP or network
administrator provides user with this information.
Interface: Select an interface, WAN or LAN, to connect to the Internet.
Metric: Select which metric that user want to apply to this configuration.
Add: Click to add the configuration to the static IP address table at the bottom of
the page.
Update: Select one of the entries in the static IP address table at the bottom of the
Network Address: Displays the network IP address of the connected node.
Network Mask: Displays the network (subnet) mask of the connected node.
Gateway Address: Displays the gateway address of the connected node.
Interface: Displays whether the node is connected via a WAN or LAN.
Metric: Displays the metric of the connected node.
page and, after changing parameters, click “Update” to confirm the changes.
Delete: Select one of the entries in the static IP address table at the bottom of the
page and click “Delete” to remove the entry.
New: Click “New” to clear the text boxes and add required information to create a
new entry.
Type: Displays whether the node has a static or dynamic IP address
33
34
Download from Www.Somanuals.com. All Manuals Search And Download.
MAC Filters
Access
This page enables you to define access restrictions, set up protocol and IP filters,
create virtual servers, define access for special applications such as games, and set
firewall rules.
Filters
Using filters to deny or allow the users to access. Five types of filters to select:
MAC, URL blocking, IP, Protocol filter and Domain blocking.
MAC Filter: Enables you to allow or deny Internet access to users within the
LAN based upon the MAC address of their network interface. Click the radio
button next to Disabled to disable the MAC filter.
Disable: Disable the MAC filter function.
Allow: Only allow computers with MAC address listed in the MAC Table.
Deny: All users are allowed Internet access except those computers in the MAC
Table are deny Internet access.
MAC Table: Use this section to create a user profile which Internet access is
denied or allowed. The user profiles are listed in the table at the bottom of the
page. (Note: Click anywhere in the item. Once the line is selected, the fields
automatically load the item's parameters, which you can edit.)
Name: Type the name of the user to be permitted/denied access.
MAC Address: Type the MAC address of the user's network interface.
Add: Click to add the user to the list at the bottom of the page.
Update: Click to update information for the user, if you have changed any of the
fields.
Delete: Select a user from the table at the bottom of the list and click Delete to
remove the user profile.
New: Click New to erase all fields and enter new information.
35
36
Download from Www.Somanuals.com. All Manuals Search And Download.
URL Blocking
IP Filters
You could enable URL blocking to deny the users from accessing the specified
URL. Add those specified URL in the text box.
This screen enables you to define a minimum and maximum IP address range
filter; all IP addresses falling in the range are not allowed Internet access. The IP
filter profiles are listed in the table at the bottom of the page. (Note: Click
anywhere in the item. Once the line is selected, the fields automatically load the
item's parameters, which you can edit.)
Enable / Disable: Enable or Disable the URL blocking function of the WLAN
Router.
Add: Add the specific URL to the URL blocking list.
Delete: Selected a URL from the blocking list then click the Delete button to
remove the URL from the URL Blocking list.
Enable: Click to enable or disable the IP address filter.
Range Start: Type the minimum address for the IP range. IP addresses falling
between this value and the Range End are not allowed to access the Internet.
Range End: Type the minimum address for the IP range. IP addresses falling
between this value and the Range Start are not allowed to access the Internet.
Add: Click to add the IP range to the table at the bottom of the screen.
Update: Click to update information for the range if you have selected a list item
and have made changes.
Delete: Select a list item and click Delete to remove the item from the list.
Clear: Click the Clear button to erase all fields and enter new information.
37
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Domain Blocking
Protocol Filters
You could specify the domains that allow users to access or deny by clicking one
of the two items. Also, add the specified domains in the text box.
This screen enables you to allow and deny access based upon a communications
protocol list you create. The protocol filter profiles are listed in the table at the
bottom of the page.
Note: When selecting items in the table at the bottom, click anywhere in the item.
The line is selected, and the fields automatically load the item's parameters, which
you can edit.
Disable: Disable the Domain Blocking function.
Allow: Allow users to access all domains except “Blocking Domains”.
Deny: Deny users to access all domains except “Permitted Domains”.
Blocked/Permitted Domains: List domains you will Blocked or Permotted.
Add: Click to Add button to add domain to the Blocked/Permitted Domains list.
Delete: Select a user from the table at the bottom of the list and click Delete to
remove the user profile.
Enable: Click to enable or disable the Protocol filter.
Name: Type the name of the user to be denied access.
Protocol: Select a protocol (TCP or UDP) to use for the virtual server.
Port Range: Type the port range of the protocol.
Add: Click to add the protocol filter to the table at the bottom of the screen.
Update: Click to update information for the protocol filter if user have selected a
list item and have made changes.
Delete: Select a list item and click Delete to remove the item from the list.
New: Click “New” to erase all fields and enter new information.
39
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Add: Click to add the virtual server to the table at the bottom of the screen.
Update: Click to update information for the virtual server if user have selected a
list item and have made changes.
Delete: Select a list item and click “Delete” to remove the item from the list.
New: Click “New” to erase all fields and enter new information.
Virtual Server
This screen enables user to create a virtual server via the router. If the router is set
as a virtual server, remote users requesting Web or FTP services through the WAN
are directed to local servers in the LAN. The router redirects the request via the
protocol and port numbers to the correct LAN server. The Virtual Sever profiles are
listed in the table at the bottom of the page.
Note: When selecting items in the table at the bottom, click anywhere in the item.
The line is selected, and the fields automatically load the item's parameters, which
user can edit.
Special AP
This screen enables user to specify special applications, such as games, that require
multiple connections that are inhibited by NAT. The special applications profiles
are listed in the table at the bottom of the page.
Note: When selecting items in the table at the bottom, click anywhere in the item.
The line is selected, and the fields automatically load the item's parameters, which
user can edit.
Enable: Click to enable or disable the application profile. When enabled, users will
be able to connect to the application via the router WAN connection. Click
“Disabled” on a profile to prevent users from accessing the application on the
WAN.
Enable: Click to enable or disable the virtual server.
Name: Type a descriptive name for the virtual server.
Protocol: Select a protocol (TCP or UDP) to use for the virtual server.
Private Port: Type the port number of the computer on the LAN that is being used
to act as a virtual server.
Name: Type a descriptive name for the application.
Public Port: Type the port number on the WAN that will be used to provide access
to the virtual server.
LAN Server: Type the LAN IP address that will be assigned to the virtual server.
41
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Trigger: Defines the outgoing communication that determines whether the user has
legitimate access to the application.
Firewall Rule
This screen enables user to set up the firewall. The router provides basic firewall
functions, by filtering all the packets that enter the router using a set of rules. The
rules are in an order sequence list--the lower the rule number, the higher the priority
the rule has.
ꢀ
ꢀ
ꢀ
ꢀ
Protocol: Select the protocol (TCP, UDP, or ICMP) that can be used to
access the application.
Port Range: Type the port range that can be used to access the application
in the text boxes.
Incoming: Defines which incoming communications users are permitted
to connect with.
Protocol: Select the protocol (TCP, UDP, or ICMP) that can be used by
the incoming communication.
ꢀPort: Type the port number that can be used for the incoming communication.
Add: Click to add the special application profile to the table at the bottom of the
screen.
Update: Click to update information for the special application if user have
selected a list item and have made changes.
Delete: Select a list item and click Delete to remove the item from the list.
New: Click “New” to erase all fields and enter new information.
DMZ
This screen enables user to create a DMZ for those computers that cannot access
Internet applications properly through the router and associated security settings.
Note: Any clients added to the DMZ exposes the clients to security risks such as
viruses and unauthorized access.
Enable: Click to enable or disable the firewall rule profile.
Name: Type a descriptive name for the firewall rule profile.
Action: Select whether to allow or deny packets that conform to the rule.
Source: Defines the source of the incoming packet that the rule is applied to.
ꢀ
ꢀ
ꢀ
Interface: Select which interface (WAN or LAN) the rule is applied to.
IP Range Start: Type the start IP address that the rule is applied to.
IP Range End: Type the end IP address that the rule is applied to.
Destination: Defines the destination of the incoming packet that the rule is applied
to.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Interface: Select which interface (WAN or LAN) the rule is applied to.
IP Range Start: Type the start IP address that the rule is applied to.
IP Range End: Type the end IP address that the rule is applied to.
Protocol: Select the protocol (TCP, UDP, or ICMP) of the destination.
Port Range: Select the port range.
Enable: Click to enable or disable the DMZ.
DMZ Host IP: Type a host IP address for the DMZ. The computer with this IP
address acts as a DMZ host with unlimited Internet access.
Add: Click to add the rule profile to the table at the bottom of the screen.
Update: Click to update information for the rule if user have selected a list item
and have made changes.
Apply: Click to save the settings.
43
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Delete: Select a list item and click “Delete” to remove the item from the list.
Remote Management
New: Click “New” to erase all fields and enter new information.
Priority Up: Select a rule from the list and click “Priority Up” to increase the
priority of the rule.
This screen enables user to set up remote management. Using remote management,
the router can be configured through the WAN via a Web browser. A user name
and password are required to perform remote management.
Priority Down: Select a rule from the list and click “Priority Down” to decrease
the priority of the rule.
Update Priority: After increasing or decreasing the priority of a rule, click
“Update Priority” to save the changes.
Management
Management enables user to set up SNMP and Remote Management feature.
SNMP
This screen enables you to configure the SNMP.
HTTP: Enables user to set up HTTP access for remote management.
Allow to Ping WAN Port: Type a range of router IP addresses that can be pinged
from remote locations
UPNP Enable: UPNP is short for Universal Plug and Play that is a networking
architecture that provides compatibility among networking equipment, software,
and peripherals. The Router is an UPnP enabled router and will only work with
other UPnP devices/software. If user does not want to use the UPnP functionality,
selecting “Disabled” can disable it.
Gaming mode: If user is experiencing difficulties when playing online games or
even certain applications that use voice data, user may need to enable Gaming
Mode for these applications to work correctly. When not playing games or using
these voice applications, it is recommended that Gaming Mode be disabled.
PPTP: Enables user to set up PPTP access for remote management.
IPSec: Enables user to set up IPSec access for remote management.
IDENT: Default is stealth. This enables user to set port 113 stealth.
Enabled/Disabled: Click to enable or disable SNMP.
System Name: A name given to the router.
System Location: Description the location of the router (normally, the DNS name).
System Contact: Description the contact information for the person responsible for
the router.
Community: SNMP system name for exchanging SNMP community messages.
The name can be used to limit SNMP messages passing through the network. The
default name is 'public.'
Trap Receiver: Type the name of the destination PC that will receive trap
messages.
45
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Firmware
Tools
This screen enables user to keep the router firmware up to date.
This page enables user to restart the system, save and load different settings as
profiles, restore factory default settings, run a setup wizard to configure router
settings, upgrade the firmware, and ping remote IP addresses.
Reset
Click “Restart” to restart the system in the event the system is not performing
correctly.
Please follow the below instructions:
Download the latest firmware from the manufacturer's Web site, and save it to disk.
Click “Browse” and go to the location of the downloaded firmware file.
Select the file and click “Upgrade” to update the firmware to the latest release.
Settings
Ping Test
This screen enables user to save settings as a profile and load profiles for different
circumstances. User can also load the factory default settings, and run a setup
wizard to configure the router and router interface.
The ping test enables user to determine whether an IP address or host is present on
the Internet. Type the host name or IP address in the text box and click Ping.
Save Settings: Click “Save” to save the current configuration as a profile that can
load when necessary.
Load Settings: Click “Browse” and go to the location of a stored profile. Click
“Load” to load the profile's settings.
Restore Factory Default Settings: Click “Restore” to restore the default settings.
All configuration changes will lose.
47
48
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
General
Standards
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.11g; IEEE 802.11b
Protocol
CSMA/CD
Radio Technology
Data Transfer Rate
IEEE 802.11g Orthogonal Frequency Division Modulation
802.11b: 1, 2, 5.5, 11Mbps (auto sense)
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps(auto sense)
Super-GTM: 108Mbps
Ethernet: 10Mbps (half duplex), 20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half duplex), 200Mbps (full- duplex)
Star
Topology
Receiver Sensitivity 54Mbps: Typical -70dBm @ 10% PER (Packet Error Rate)
11Mbps: Typical -85dBm @ 8% PER (Packet Error Rate)
13dBm typically @ 802.11g
TX Power
13dBm typically @ 802.11b
10BASE-T: 2-pair UTP Cat. 3,4,5 (100 m), EIA/TIA- 568 100-ohm
Network Cables
STP (100 m)
100BASE-TX: 2-pair UTP Cat. 5 (100 m), EIA/TIA-568 100-ohm
STP (100 m)
Frequency Range
Modulation
Schemes
2412 ~ 2484 MHz ISM band (channels 1 ~ 14)
DBPSK/DQPSK/CCK/OFDM
Security
Channels
64/128-bits WEP Encryption; WPA, WPA-PSK, WPA2, WPA2-PSK
1 ~ 11 channels (FCC); 1 ~ 13 channels (ETSI);
1 ~ 14 channels (MKK)
Number of Ports
LAN: 4 x 10/100Mbps Auto-MDIX Fast Ethernet port
WAN: 1 x 10/100Mbps Auto-MDIX Fast Ethernet port
Physical and Environmental
DC inputs
5VDC/2.5A
Power Consumption 5W (Max)
Temperature
Humidity
Dimensions
EMI:
Operating: 0° ~ 40° C, Storage: -10° ~ 70° C
Operating: 10% ~ 90%, Storage: 5% ~ 90%
147 x 115 x 35 mm (W x H x D) without Antenna
FCC Class B, CE Mark B
49
Download from Www.Somanuals.com. All Manuals Search And Download.
|