Calculite® HID Adjustable Accent C6T6A-MHT6RS
Page 1 of 2
6" Aperture, T6 Ceramic Metal Halide, Spot
20" to 30"
10-5/8"
20-1/4" (Electronic)
22-1/8" (Magnetic)
Top View
Spot Upper
Reflector
Ceiling Cutout: 9 9/16” (167mm) Dia.
For Complete Fixture Order: Trim Kit + Spot Upper Reflector (MHT6RS) + Frame-In Kit. Each Sold Separately.
Trim Kit + Spot Upper Reflector
Frame-In Kit
Lamp
C6T6A
+
MHT6RS (Spot Upper Reflector)
C6A39T6E1 Electronic 120V
C6A39T6E2 Electronic 277V
C6A70T6E1 Electronic 120V
C6A70T6E2 Electronic 277V
C6A15T6E1 Electronic 120V
C6A15T6E2 Electronic 277V
39W T6
39W T6
70W T6
70W T6
150W T6
150W T6
Ceramic MH
Ceramic MH
Ceramic MH
Ceramic MH
Ceramic MH
Ceramic MH
Ceramic MH
CLW
CLP
Specular Clear, White Painted Flange
Specular Clear, Matching Flange
CCDW Comfort Clear Diffuse, White Painted Flange
CCDP Comfort Clear Diffuse, Matching Flange
CCZW Champagne Bronze, White Painted Flange
CCZP Champagne Bronze, Matching Flange
Magnetic 120V/277V 150W T6
Features
Electrical
Electronic Ballast: 120V or 277V, 50/60 Hz., encased, high power factor, T.H.D
<15%, thermally and transient protected, RMI/RFI complies with FCC Part 18 on-
consumer equipment, shut-down circuit at end of lamp life, sound rating “A”,
-5°F (-20°F for 150W) minimum starting temperature, Type 1 outdoor rating.
*150W Magnetic Ballast: 120/277V dual voltage, 60 Hz., encased and potted,
HX-HPF circuit type, high power factor, sound rating “B”, -20°F minimum starting
temperature, Type 1 Outdoor rating.
1. Spot Upper Reflector: Specular faceted aluminum; provides 12° beam.
Interchangeable with 25° Narrow Flood (MHT6RNF) and 40° Flood (MHT6RF);
see spec sheets C6T6A-MHT6RNF and C6T6A-MHT6RF.
2. Trim Kit: Low brightness aperture cone; anodized aluminum, self-flanged in
painted white or aperture-matching polished flange. Consult factory for other
finishes.
3. Lamp Shield: High-temperature glass as required by code; captive
during re-lamping.
4. Trim Kit Adjustment Mechanism: Provides 40° vertical tilt, 360° horizon-
tal rotation; lockable. Patented EZ-Aim™ Helical Drive System provides fast
and accurate hot aiming with Philips screwdriver.
5. Socket Housing: Galvanized steel, pre-wired with G12 pulse rated socket.
Snaps onto yoke for secure attachment without tools; unitized construction
assures proper alignment of lamp to optics for consistent optical performance.
6. Frame Housing: Steel, 0.029" (22-Ga.), matte black finish. Removable cover
for top re-lamping.
Ballast
ANSI Code Voltage Max. Amps Input Watts
39W MH M130
70W MH M139
150W MH M142
* 150W MH M142
120/277
120/277
120/277
120/277
0.39/0.17
0.67/0.28
1.40/0.60
3.70/1.60
44
78
167
180
Options and Accessories
Chicago Plenum: Consult Factory
Labels
UL (Suitable for Damp Locations), CSA, I.B.E.W.
For 150W, install fixtures with minimum spacing between:
1. Center-to center of adjacent luminaries: 2 feet.
7. Frame Vertical Adjustment Mechanism: Accommodates mounting to
virtually any ceiling system using pre-installed mounting bars, or 1/2" EMT
tubing (by others). Single locking feature secures all adjustments. Alignment
holes and markings allow fixture to be pre-set prior to installation. Final
adjustment can be made from below from inside fixture.
2. Top of luminaire to overhead building member: 1/2 inch.
3. Luminaire center to side building member: 1 foot.
8. Mounting Bars: Galvanized steel, 0.048" (18-ga.), pre-installed telescoping
bars extend to 30" long and lock securely into position. Built-in locking tabs
provide positive attachment to common T-bar systems. Self-centering feature
simplifies installation in 24" O.C. grid systems. Attaches to steel or wood
joists without accessories.
Job Information
Type:
Job Name:
Cat. No.:
9. Retention Springs: Rust resistant springs secure trim for quick, tool-less
installation.
10. Ballast / Cover Assembly: Accessible from below and removable without
tools for inspection and ballast replacement .
Lamp(s):
Notes:
11. Junction Box: 0.059" (16-ga.) galvanized steel. UL listed for 8 No. 12 AWG,
90°C through branch circuit conductors. Allows inspection from below.
12. Accessory Holder: Sold separately catalog # CAH6; die-formed steel,
matte black finish, slide-in installation. Accepts up to two 4 3/4" dia. media.
13. Thermal Protector: (Not Shown) Meets NEC and UL requirements. Do not
install insulation above nor within 3" (76mm) of any part of the luminaire.
Lightolier a Genlyte company
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2006 Genlyte Group LLC • B0406
|