8 STACK MULTI-JUNGLE (SM81)
WITH 2 ADJUSTABLE PULLEYS
UNPACKING AND ASSEMBLY INSTRUCTIONS
M051-K50-B117
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
UNPACKING
Follow the steps below when unpacking the components of the SM81.
1. Cut off the shipping wrapper.
2. Remove the parts boxes and shipping boards.
3. Remove the items in the parts boxes. These items are shown in Figure 1.
A. Remove the bolts bag.
B. Remove the parts shown below. Parts that are used to build the SM81 are
described in the section HARDWARE at the end of these instructions.
Figure 1. Parts box contents (box 1 on left, box 2 on right).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
ASSEMBLY
Figure 2 shows an assembled SM81.
Figure 2. SM81 main components (seats and cables removed for clarity).
1. Cubes (2)
5. Lat tops (2)
2. Low row bench (2)
3. Lat bench (2)
4. Connecting beam (1)
6. Tricep top (2)
7. 300 lb. Weight stacks (4)
8. 190 lb. Weight stacks (4)
1. Place the two weight “cubes” in their “final resting spots.” The cubes will be
approximately 11’4” apart as shown in Figure 3.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
Figure 3. Set the weight stack cubes.
2. Bolt on the teardrop pulleys above the benches (see Figure 4) on both cubes using
two 3/8” x 2-3/4” hex head bolts (used to bolt the cross beam to the cross members
and the adjustable pulley tops to the top beams). Include the 3/8” flat washer, end cap
washers, end caps and 3/8” Nyloc (locknut). Use the bolt configuration shown in
Figure 5. You may wish to use a pinch bar to align the bolt holes.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
Figure 4. Bolt on the teardrop pulleys.
Figure 5. Configuration for 2-3/4” and 3” bolts.
3. Using a 5/8” socket with extension and combination wrench, bolt on the connecting
beam to the cubes using two of the large 7/16” x 6” bolts, 7/16” washers, and 7/16”
nuts, end cap washers and end caps. Figure 6 shows the connected cubes.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
4. Using a 5/8” socket and combination wrench, mount the 56” lat tops (part T from
HARDWARE section) to the cells by inserting two of the large 7/16” by 6” bolts using
the hardware configuration shown in Figure 7. Mount the 29” tricep top (part U in
HARDWARE section) and adjustable crossover top (part V in HARDWARE section)
to the frame and connecting beam (See Figure 6). You will need to remove the
pulleys from the teardrop pulley assemblies to gain clearance for the socket wrench
extension. Leave the pulleys out of the housings until the cables have been installed.
3/8” x 3” (4)-
bolt top
beams together
7/16” x 6” (8)-
mount on tops
U
T
U
T
Remove pulleys from
housings to give clearance
to socket extension
Figure 6. Mount lat tops and tricep tops.
Figure 7. Configuration for 6” bolts.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
Figure 8. Mount rubber bumpers and the weight stacks.
5. Install the weight stacks. To do this:
A. Using a 9/16” socket and combination wrench, remove the tricep back rest bolts
(see Figure 9).
B. Using a 9/16” socket and combination wrench, unbolt the top plate and remove
the guide rods (see Figure 9).
Figure 9. Remove the tricep back rest, the top plate and the guide rods.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
C. Prepare the weight stack. Slide the guide rods (2) through the weight stacks (1)
as shown below. Place rubber bumpers (3) on the bottoms of each guide rod.
Make sure the pull pin (4) is in the bottom weight plate.
D. Flip over the weight stacks. When shipped, the weight stacks have the pull pins
facing upward. You will need to flip the stacks over so that the pull pins are facing
outward when they are loaded onto the machine. Since the pull pins will be facing
downward when they are flipped over, it is recommended that you put the stacks
on a padded carpet to keep the pins from being damaged.
E. Set the weight stacks onto the machine. Using a piano dolly, lift the weight
stacks over the bottom plate and set the stacks onto the rubber bumpers with the
plate numbers facing outward. The 300 lb weight stacks need to be facing the
“sides” of the cells (where the benches will be attached). The 190 lb weight
stacks will need to be facing the “outsides” and “insides” of the cells (where the
tricep pulley adjustable pulleys will be attached). Make sure the pull pins are
facing outward.
C. Prepare the weight stack-
add bumpers to bottom, insert
guide rods, put pull pin in
bottom stack.
D. Flip over the weight stack
onto piano dolly.
E. Hoist the weight
stack onto the machine.
F. With the top plate on the guide rods, bolt on the top plate to the top of the cells as
shown in Figure 10 using a 9/16” socket and combination wrench and the 3” bolts
(with cap washers) that were previously inserted.
Figure 10. Bolt on the top plate.
6. Using a 7/8” combination wrench, bolt the floating pulleys into the 190 lb weight
stacks (except for the tricep pushdown weight stacks- the one with the tricep back
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
rest mounted to the frame as shown in Figure 9). You will need to remove the pulley
from the housing to thread the plug into the weight stack bayonet. Make sure the
9/16” jam nut is threaded 1-5/8” away from the pulley as shown in Figure 11. Leave
the pulleys out since you will need to have them out when the cable is routed.
Figure 11. Bolt the floating pulleys into the 190 lb weight stacks.
7. Mount adjustable pulley brackets. When shipped, the adjustable pulley brackets look
like the ones shown in Figure 12. The bolts need to be removed and the bracket
needs to be positioned so that the top of the bracket is in the top hole as shown by
the arrow in Figure 12. Use a 3” bolt with flat washers, end cap washers and end
caps. When you remove the bolts, leave the pulley bolt and pulley out since you will
need to thread the cable with the pulley removed.
Figure 12. Mount adjustable pulley bracket.
8. Mount the seated row and lat benches to the frame. Using the bolts specified in
Figure 13 and a 9/16” socket and combination wrenches, mount the benches as
shown in Figures 13 and 14.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
Use a pinch bar to align the
seat frame holes to the cubes
Figure 13. Mount the benches to the frame.
Figure 14. Bolt the benches to the frame.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
INSTALLING THE CABLES
The SM81 uses eight cables. There are three different types of cable used on the SM81. They
are:
1. Adjustable crossover cables (ball end cables) (2).
2. Low row cable (the long cables) (2).
3. Lat pulldown and tricep cables (4).
The lat and tricep cables can be identified by their short length, the low row cables can be
identified by their long length and the adjustable crossover cables can be identified by the ball
on the end of the cable. The routings for these cables are shown in Figures 15, 16, 17 and 18
below.
NOTE: YOU MUST REMOVE ALL PULLEYS TO ROUTE THE CABLES.
USE A 9/16” COMBINATION WRENCH AND SOCKET TO DO THIS
(SEE FIGURE 16). YOU MAY WISH TO REMOVE THE SHOULDER
BOLTS (FIGURE 16 RIGHT SIDE) BY USING A 3/8” COMBINATION
WRENCH AND A 1/8” HEX KEY WRENCH. WHEN YOU HAVE
ROUTED THE CABLES, REPLACE ALL PULLEYS AND PLACE
END CAPS ON NUT AND BOLT ENDS. YOU MAY NEED TO PRY
THE PULLEY HOUSINGS OPEN TO REPLACE THE PULLEYS.
Figure 15. Removing the pulley bolts.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
ADJUSTABLE CROSSOVER CABLE ROUTING
Once you’ve removed the pulleys as described previously, route the three adjustable
crossover cables as shown in Figure 16.
Figure 16. Adjustable crossover cable routing.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
Figure 17. Adjustable crossover cable end detail.
Using a 7/8” wrench, tighten the jam nut onto the adjustable pulley threads as shown in Figure
17. Place a rubber cap on the top of the cable as shown in Figure 17 (right).
LOW ROW CABLE ROUTING
Route the low row cables as shown in Figure 18.
Figure 18. Low row cable routing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
Bolt the cable to the weight stacks as shown in Figure 19. Thread the 7/8” nut up on the
cable bolt as shown at left. Screw the bolt down into the weight stack as shown at right.
Tighten the bolt with a 7/8” combination wrench.
Figure 19. Screw the cable into the weight stack.
LAT PULLDOWN CABLE ROUTING
Route the lat pulldown cable as shown in Figure 20. Screw the cable into the weight stack as
shown previously in Figure 19.
Figure 20. Lat pulldown cable routing.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
TRICEP PUSHDOWN CABLE ROUTING
Route the tricep pushdown cable as shown in Figure 21. Screw the cable into the weight stack
as shown previously in Figure 19.
Figure 21. Tricep pushdown cable routing.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
HARDWARE
½
½
½
½
½
½
0
1
2
3
4
5
6
Hardware Figure 1. Assembly Parts.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
The parts shown in Hardware Figure 1 are used to assemble the SM81. They are:
A. 7/16” x 6” hex head bolt (used to bolt the tricep top beam, adjustable crossover top
beam, lat top beams, and connecting beam to the tops of the cubes)
B. 7/16” flat washer
C. 7/16” cap washer (used on the head end of the 6” bolt so end cap will fit on the nut)
D. 7/16” hex head nut
E. 3/8” x 3” hex head bolt (used to bolt the cross beam to the cross members, the
adjustable pulley tops to the top beams, and the bottom bolts on the lat benches)
F. 3/8” x 2-3/4” hex head bolt (used for all other connections)
G. End caps (bolt covers)
H. 3/8” flat washer
J. 3/8” end cap washers (end caps snap onto them)
K. 3/8” Nyloc (locknut)
The black rubber caps shown in Hardware Figure 2 are used to cap the ends of the cables
that are threaded to the adjustable pulleys.
Hardware Figure 2. Rubber caps.
L. Rubber cap
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
The part shown in Hardware Figure 3 is the 9/16” cable jam nut that’s used to secure the
cables to the weight stacks.
Hardware Figure 3. Cable jam nut.
M. Cable jam nut
Hardware Figure 4 shows the types of cables that are included with the SM81.
Hardware Figure 4. Cables.
N. Lat pulldown cables (same as tricep cable) (2)
P. Tricep cable (same as lat pulldown cable) (2)
Q. Low row cables (long cables) (2)
R. Adjustable crossover cables (ball end) (2)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
S
T
U
Hardware Figure 5. Top assemblies.
S. Teardrop pulleys (bolt on above lat and seated row benches) (4)
T. 56” Lat tops (bolt to top of cells with pulleys above lat benches) (2)
U. 29” Tricep top (bolt on to 56” lat top bar) (2)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
Hardware Figure 6. Weight stack rubber bumpers.
W. Weight stack rubber bumpers (inserted under weight stacks) (16)
Hardware Figure 7. Floating pulleys.
X. Floating pulleys (bolt to 190 lb weight stacks other than tricep pushdown stack) (2)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
PARTS LIST
Part #
ID
Description
Quantity
Main components
Cubes
Low row bench
Lat bench
Connecting beam
Lat tops
Tricep top
2
2
2
1
2
2
4
4
1
2
3
4
5
6
7
8
300 lb weight stack
190 lb weight stack
Cables, caps & nuts
L
0017-00042-0936
0017-00103-0234
0017-00101-1408
0017-00101-1408
0017-00101-1422
0017-00101-1561
Rubber cap
Cable jam nut
Lat pulldown cable
Tricep cable
Low row cable
2
12
2
2
2
M
N
P
Q
R
Adjustable crossover cable
2
6” bolt hardware
0017-00101-1561
0017-00104-0363
0017-00104-0366
0017-00103-0233
7/16” x 6” hex head bolt
7/16” flat washer
7/16” cap washer
7/16” Nyloc nut
8
8
8
8
A
B
C
D
2-3/4” & 3”
bolt hardware
0017-00101-1422
0017-00101-1408
0017-00042-0969
0017-00104-0313
0017-00104-0368
0017-00103-0217
3/8” x 3” hex head bolt
3/8” x 2-3/4” hex head bolt
End cap
3/8” flat washer
3/8” end cap washer
3/8” Nyloc nut
10
24
68
68
68
34
E
F
G
H
J
K
Pulleys and bumpers
W
X
0017-00042-0993
Weight stack rubber bumper
Floating pulley
16
2
Handle and bar
hardware
Safety carabiner
Crossover handle
Tricep bar
Lat bar
Low row handle
Leg strap
8
2
2
2
2
1
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SM81 Unpacking & Assembly Instructions
Pulley hardware
(installed)
0017-00101-1413
0017-00104-0368
0017-00103-0217
1-3/4” Bolt
Cap washer
3/8” Nyloc nut
Floating pulley
hardware (installed)
0017-00101-1413
0017-00104-0313
0017-00103-0217
1-3/4” Bolt
Flat washer
3/8” Nyloc nut
23
Download from Www.Somanuals.com. All Manuals Search And Download.
|