4 STACK MULTI-JUNGLE (SM42)
WITH 2 ADJUSTABLE PULLEYS
UNPACKING AND ASSEMBLY INSTRUCTIONS
M051-K50-A142
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
UNPACKING
Follow the steps below when unpacking the components of the SM42.
1. Cut off the shipping wrapper.
2. Remove the parts box and shipping boards.
3. Remove the items in the parts box. These items are shown in Figure 1.
A. Remove the bolts bag.
B. Remove the parts shown below. Parts that are used to build the SM42 are
described in the section HARDWARE at the end of these instructions.
Figure 1. Parts box contents.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
ASSEMBLY
Figure 2 shows an assembled SM42.
4
1
8
6
5
2
7
3
Figure 2. SM42 main components.
1. 1 stack cell
2. 4 stack cell
3. Lat bench
5. Lat top
6. Tricep top
7. 300 lb. Weight stacks (1)
8. 190 lb. Weight stacks (3)
4. Connecting beam
1. Place the two weight “cells” in their final resting spots. The cells will be
approximately 11’4” apart as shown in Figure 3.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Figure 3. Set the weight stack cells.
2. Bolt on the teardrop pulleys above the benches (see Figure 4) on the 3 stack cell
using two 3/8” x 2-3/4” hex head bolts (used to bolt the cross beam to the cross
members and the adjustable pulley tops to the top beams). Include the 3/8” flat
washer, end cap washers, end caps and 3/8” Nyloc (locknut). Use the bolt
configuration shown in Figure 5. You may wish to use a pinch bar to align the bolt
holes.
3/8” x 2-3/4” (2)
Figure 4. Bolt on the teardrop pulleys.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Figure 5. Configuration for 2-3/4” and 3” bolts.
3. Bolt on the connecting beam (part 4 from Figure 2) using a 5/8” socket with
extension and combination wrench, to the cells using two of the large 7/16” x 6” bolts,
7/16” washers, and 7/16” nuts (parts A, B, and C in HARDWARE section at end of
these instructions), end cap washers and end caps (parts F and H in HARDWARE
section). Figure 6 shows the connected cells. You will need to remove the pulleys
from the teardrop pulley assemblies to gain clearance for the socket wrench
extension. Leave the pulleys out of the housings until the cables have been installed.
7/16” x 6” (6)-
mount on tops
T
U
3/8” x 3” (2)-
bolt top
beams together
Remove pulleys from
housings to give clearance
to socket extension
Figure 6. Bolt on the connecting beam, lat top, and tricep top.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
4. Mount the 56” lat top (part T from HARDWARE section) to the 4-stack cell using a
5/8” socket and combination wrench. Insert two of the large 7/16” by 6” bolts using the
hardware configuration shown in Figure 7. Mount the 29” tricep top (part U in
HARDWARE section) to the frame and connecting beam (See Figure 7).
Figure 7. Configuration for 6” bolts.
150 lb.
weight stack
300 lb.
weight stack
150 lb.
weight stack
Figure 8. Mount the weight stacks.
5. Mount the weight stacks to the 4-stack cell. To do this:
A. Remove the tricep back rest bolts using a 9/16” socket and combination
wrench (see Figure 9).
B. Unbolt the top plate and remove the guide rods using a 9/16” socket and
combination wrench (see Figure 9).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Figure 9. Remove the tricep back rest, the top plate and the guide rods.
C. Prepare the weight stack-
add bumpers to bottom, insert
guide rods, put pull pin in
bottom plate of stack.
D. Flip over the weight stack
onto piano dolly.
E. Hoist the weight
stack onto the machine.
Figure 10. Putting on the weight stacks.
C. Prepare the weight stacks. Slide the guide rods (2) through the weight stacks
(1) as shown above. Place rubber bumpers (3) on the bottoms of each guide rod.
Make sure the pull pin (4) is in the bottom weight plate.
D. Flip over the weight stacks. When shipped, the weight stacks have the pull pins
facing upward. You will need to flip the stacks over so that the pull pins are facing
outward when they are loaded onto the machine. Since the pull pins will be facing
downward when they are flipped over, it is recommended that you put the stacks
on a padded carpet to keep the pins from being damaged.
E. Set the weight stacks onto the machine. Using a piano dolly, lift the weight
stacks over the bottom plate and set the stacks onto the rubber bumpers with the
plate numbers facing outward. The 300 lb weight stacks need to be facing the
“sides” of the cells (where the benches will be attached- see Figure 9). The 190 lb
weight stacks will need to be facing the “outsides” and “insides” of the cells
(where the tricep pulley adjustable pulleys will be attached- see Figure 9). Make
sure all pull pins are facing outward.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
F. Bolt on the top plate. With the top plate on the guide rods, bolt on the top plate
to the top of the cells as shown in Figure 11 using a 9/16” socket and combination
wrench and the 3” bolts (with cap washers) that were previously inserted.
Figure 11. Bolt on the top plate.
6. Bolt the floating pulley into the 190 lb cable crossover weight stack (NOT
intended for the tricep pushdown weight stack- the one with the tricep back rest
mounted to the frame as shown in Figure 9) using a 7/8” combination wrench. You
will need to remove the pulley from the housing to thread the plug into the weight
stack bayonet. Make sure the 9/16” jam nut is threaded 1-5/8” away from the pulley
as shown in Figure 12. Leave the pulleys out since you will need to have them out
when the cable is routed.
Figure 12. Bolt the floating pulley into the 190 lb weight stack (away from the tricep
pushdown weight stack).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
7. Mount adjustable pulley brackets. When shipped, the adjustable pulley brackets
look like the ones shown in Figure 13. The bolts need to be removed and the bracket
needs to be positioned so that the top of the bracket is in the top hole as shown by
the arrow in Figure 13. Use a 3” bolt with flat washers, end cap washers and end
caps. When you remove the bolts, leave the pulley bolt and pulley out since you will
need to thread the cable with the pulley removed.
Figure 13. Mount adjustable pulley bracket.
8. Mount the seated row and lat bench to the frame. Using the bolts specified in
Figure 14 and a 9/16” socket and combination wrenches, mount the benches as
shown in Figures 14 and 15.
3/8” x 2-3/4” (4)
3/8” x 3” (2)
Figure 14. Mount the benches to the frame.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Figure 15. Bolt the benches to the frame.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
INSTALLING THE CABLES
The SM42 uses four cables. There are two different types of cable used on the SM42. They
are:
1. Adjustable crossover cables (ball end cables) (2).
2. Lat pulldown and tricep cables (2).
The lat and tricep cables can be identified by their short length and the adjustable crossover
cables can be identified by the ball on the end of the cable. The routings for these cables are
shown in the figures below.
NOTE: YOU MUST REMOVE ALL PULLEYS TO ROUTE THE CABLES.
USE A 9/16” COMBINATION WRENCH AND SOCKET TO DO THIS
(SEE FIGURE 16). YOU MAY WISH TO REMOVE THE SHOULDER
BOLTS (FIGURE 16 RIGHT SIDE) BY USING A 3/8” COMBINATION
WRENCH AND A 1/8” HEX KEY WRENCH. WHEN YOU HAVE
ROUTED THE CABLES, REPLACE ALL PULLEYS AND PLACE
END CAPS ON NUT AND BOLT ENDS. YOU MAY NEED TO PRY
THE PULLEY HOUSINGS OPEN TO REPLACE THE PULLEYS.
Figure 16. Removing the pulley bolts.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
ADJUSTABLE CROSSOVER CABLE ROUTING
Once you’ve removed the pulleys as described previously, route the adjustable crossover
cable on the 4-stack cell as shown in Figure 17. The crossover cable is routed at the factory
on the 1 stack cube (shown at right in Figure 17).
Figure 17. Adjustable crossover cable routing.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Figure 18. Adjustable crossover cable end detail.
Using a 7/8” wrench, tighten the jam nut onto the adjustable pulley threads as shown in Figure
18. Place a rubber cap on the top of the cable as shown in Figure 18 (right).
LAT PULLDOWN CABLE ROUTING
Route the lat pulldown cable as shown in Figure 19.
Figure 19. Lat pulldown cable routing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Bolt the cable to the weight stacks as shown in Figure 20. Thread the 7/8” nut up on the cable
bolt as shown at left. Screw the bolt down into the weight stack as shown at right. Tighten the
bolt with a 7/8” combination wrench.
Figure 20. Screw the cable into the weight stack.
TRICEP PUSHDOWN CABLE ROUTING
Route the tricep pushdown cable as shown in Figure 21. Bolt the cable into the weight stack
as shown previously in Figure 20.
Figure 21. Tricep pushdown cable routing.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
HARDWARE
½
½
½
½
½
½
0
1
2
3
4
5
6
Hardware Figure 1. Assembly Parts.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
The parts shown in Hardware Figure 1 are used to assemble the SM42. They are:
A. 7/16” x 6” hex head bolt (used to bolt the tricep top beam, adjustable crossover top
beam, lat top beam, and connecting beam to the tops of the cells)
B. 7/16” flat washer
C. 7/16” cap washer (used on the head end of the 6” bolt so end cap will fit on the nut)
D. 7/16” hex head nut
E. 3/8” x 3” hex head bolt (used to bolt the cross beam to the cross members, the
adjustable pulley tops to the top beams, and the bottom bolts on the lat bench)
F. 3/8” x 2-3/4” hex head bolt (used for all other connections)
G. End caps (bolt covers)
H. 3/8” flat washer
J. 3/8” end cap washers (end caps snap onto them)
K. 3/8” Nyloc (locknut)
The black rubber caps shown in Hardware Figure 2 are used to cap the ends of the cables
that are threaded to the adjustable pulleys.
Hardware Figure 2. Rubber cap.
L. Rubber cap
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
The part shown in Hardware Figure 3 is the 9/16” cable jam nut that’s used to secure the
cables to the weight stacks.
Hardware Figure 3. Cable jam nut.
M. Cable jam nut
Hardware Figure 4 shows the types of cables that are included with the SM42.
P
N
Q
Hardware Figure 4. Cables.
N. Lat pulldown cables (same as tricep cable) (1)
P. Tricep cable (same as lat pulldown cable) (1)
Q. Adjustable crossover cables (ball end) (2)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Hardware Figure 5. Top assemblies.
S. Teardrop pulleys (bolt on above lat bench) (1)
T. 56” Lat top (bolt to top of 4-stack cell with pulleys above lat bench) (1)
U. 29” Tricep top (bolt on to 56” lat top bar) (1)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Hardware Figure 6. Weight stack rubber bumpers.
W. Weight stack rubber bumpers (inserted under weight stacks) (8)
Hardware Figure 7. Floating pulleys.
X. Floating pulley (bolt to 190 lb weight stack other than tricep pushdown stack) (1)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
PARTS LIST Hardware Kit: SK50-S0084-0000
Part #
ID
Description
Quantity
Main components
1-stack cell
4-stack cell
Low row bench
Connecting beam
Lat top
Tricep top
Lat bench
300 lb weight stack
190 lb weight stack
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
2
3
Cables, caps & nuts
L
0017-00042-0936
0017-00103-0234
0017-00101-1408
0017-00101-1408
0017-00101-1422
0017-00101-1561
Rubber cap
Cable jam nut
Lat pulldown cable
Tricep cable
Low row cable
1
4
1
1
1
2
M
N
P
Q
R
Adjustable crossover cable
6” bolt hardware
0017-00101-1561
0017-00104-0363
0017-00104-0366
0017-00103-0233
7/16” x 6” hex head bolt
7/16” flat washer
7/16” cap washer
7/16” Nyloc nut
6
6
6
6
A
B
C
D
2-3/4” & 3”
bolt hardware
0017-00101-1422
0017-00101-1408
0017-00042-0969
0017-00104-0313
0017-00104-0368
0017-00103-0217
3/8” x 3” hex head bolt
3/8” x 2-3/4” hex head bolt
End cap
3/8” flat washer
3/8” end cap washer
3/8” Nyloc nut
6
E
F
G
H
J
12
36
36
36
18
K
Pulleys and bumpers
W
X
0017-00042-0993
Weight stack rubber bumper
Floating pulley
8
1
Handle and bar
hardware
Safety carabiner
Crossover handle
Tricep bar
Lat bar
Low row handle
Leg strap
5
2
1
1
1
1
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SM42 Unpacking & Assembly Instructions
Pulley hardware
(installed)
0017-00101-1413
0017-00104-0368
0017-00103-0217
1-3/4” Bolt
Cap washer
3/8” Nyloc nut
Floating pulley
hardware (installed)
0017-00101-1413
0017-00104-0313
0017-00103-0217
1-3/4” Bolt
Flat washer
3/8” Nyloc nut
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|