Life Fitness Home Gym Chest Press User Manual

Chest Press  
Assembly Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chest Press  
Assembly Instructions  
1. LOOSELY assemble the FRONT BRACE (1) and REAR BRACE (2) to the  
TOWER (3) using four M10 X 130mm BOLTS (4), eight 3/8" SAE WASH-  
ERS (5) and four M10 NYLOCK NUTS (6) as shown.  
2. LOOSELY assemble the SEAT FRAME (7) to the FRONT BRACE (1) and  
REAR BRACE (2) using four M10 X 90mm BOLTS (8), eight 3/8" SAE  
WASHERS (5) and four M10 NYLOCK NUTS (6) as shown.  
3. LOOSELY assemble the TOP BRACE (9) to the SEAT FRAME (7) and  
TOWER (3) using two M10 X 90mm BOLTS (8), four 3/8" SAE WASHERS  
(5) and two M10 NYLOCK NUTS (6) at the SEAT FRAME and two M10 X  
70mm BOLTS (10), four 3/8" SAE WASHERS (5) and two M10 NYLOCK  
NUTS (6) at the TOWER as shown.  
4. Tighten all BOLTS and NUTS securely.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Insert the PIVOT SHAFT (11), LONG SPACER (12), two BEARINGS (13)  
and two SMALL SPACER (14) into the WORKARM (15) as shown.  
Carefully insert the WORKARM into the FRONT BRACE (1) and secure it  
with two M10 X 25mm BOLTS (16) and two 3/8" SAE WASHERS (5).  
Tighten the BOLTS securely.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chest Press  
Assembly Instructions  
6. Assemble the OUTPUT CAM (17), OUTPUT PLATE (18), and OUTPUT  
RING (19) using three M10 X 45mm BOLTS (20) and three 3/8" SAE  
WASHERS (5) as shown. Tighten the BOLTS securely.  
7. Assemble the REAR SHROUD (21) and FRONT SHROUD (22) to the  
TOWER (3) using four M10 X 20mm BOLTS (23), four 3/8" SAE WASH-  
ERS (5) as shown. Be sure all tabs along the sides and top of the  
SHROUDS are fully engaged in the slots located inside the TOWER.  
Tighten the BOLTS securely. Do not overtighten the BOLTS.  
8. Secure the OUTPUT CAM ASSEMBLY (A) to the TOWER HUB (B) using  
one M10 X 25mm BOLTS (16), one 3/8" SAE WASHERS (5) and one  
PLATE (24) as shown. Tighten the BOLT securely.  
IMPORTANT: Be sure the OUTPUT CAM ASSEMBLY is oriented as  
shown before securing it to the TOWER HUB.  
9. Attach the CAM GUARD (25) to the FRONT SHROUD (22) using two M5  
X 10mm PHILLIPS SCREWS (26). Tighten the SCREWS securely. Do not  
overtighten the SCREWS.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. Attach the SEAT PAD (27) to the SEAT FRAME (7) using two M10 X  
25mm BOLTS (16) and two 3/8" SAE WASHERS (5). Tighten the BOLTS  
securely.  
11. Attach the BACK PAD (28) to the SEAT FRAME (7) using two M10 X  
35mm BOLTS (29) and two 3/8" SAE WASHERS (5). Tighten the BOLTS  
securely.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chest Press  
Assembly Instructions  
NOTE: Some components have been removed from the illustration for  
clarity.  
12. Assemble one M10 HEX JAM NUT (30) onto one end of the CABLE (31)  
approximately 1/2”. Assemble the ROD END BEARING (32) to the same  
end of the CABLE until it meets the M10 HEX JAM NUT. Tighten the M10  
HEX JAM NUT securely.  
13. Loosely assemble the ROD END BEARING (32) of the CABLE (31) to the  
WORK ARM (15) using one M10 X 40mm BOLT (33), SPACER (34), 3/8"  
SAE WASHER (5) and M10 NYLOCK NUT (6)  
14. Route the CABLE (31) around the pulley on the TOP BRACE (9), over the  
CAM GUARD (25) and around the OUTPUT CAM ASSEMBLY (A). Insert  
the remaining end of the CABLE through the inner hole of the OUTPUT  
CAM ASSEMBLY.  
Insert the CABLE RETAINING PLATE (35) over the end of the CABLE.  
Install two M8 HEX JAM NUTS (37) to the end of the CABLE.  
Tighten the M8 HEX JAM NUTS until the WORKARM begins to move  
and all push pins still move in and out freely. Be sure the HEX JAM  
NUTS are tight against each other.  
15. Attach the OUTPUT CAM COVER PLATE (36) to the OUTPUT CAM  
ASSEMBLY (A) using three M10 X 45mm BOLTS (20) and three 3/8" SAE  
WASHERS (5).  
16. Place the unit in the intended place for use and check stability. If the unit  
is not stable, the FEET (C) can be adjusted by inserting or removing sup-  
plied SHIMS (38).  
To add or remove SHIMS, loosen the LEVELING FOOT BOLT (D) and  
NUT (6) until the desired shim(s) can be inserted or removed. Lightly  
tighten the BOLT and NUT. Do not over-tighten the BOLT and NUT.  
17. Install HOLE PLUGS in all open bolt holes.  
©
2006 Life Fitness, a division of Brunswick Corporation. All rights reserved.  
Life Fitness is a registered trademark of Brunswick Corporation.  
TCCP 6.05.06  
8060401 RevA-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  

LG Electronics Projector LP XG2 User Manual
Lightolier Indoor Furnishings 1001F_3d User Manual
Linksys Network Card HPN100SK User Manual
Linksys Network Card WMP110 User Manual
Lowrance electronic GPS Receiver Mapping GPS and Multimedia Player User Manual
Macsense Connectivity Network Card HomePod User Manual
Magnavox Cassette Player AZ8289 User Manual
Makita Saw 7301 User Manual
Maytag Refrigerator MBL2256KES12 User Manual
McIntosh Door WK 2 User Manual