8216 50 LB. ADD-ON KIT
ASSEMBLY INSTRUCTIONS
Part # 6812501
1
Revision: 1/12/99
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY PART #
DESCRIPTION
QTY
KEY PART #
DESCRIPTION
WEIGHT STACK LABEL (lbs.)
WEIGHT STACK LABEL (1-25)
WEIGHT PLATES
QTY
.1
1
2
3
6284501
6812701
6382301
25 HOLE WEIGHT STACK SHAFT
212-3/4” CABLEASSEMBLY
WEIGHT PLATE BUSHING 10 CT
1
1
1
4
5
6
6703801
6198501
6214501
1
5
TOWER
CABLE
SHROUD
FIGURE 1
STEP 1:
•
Unscrew the threaded end of the CABLE (67846) from the WEIGHT STACK SHAFT of the HEAD PLATE.
•
Completely remove CABLE (67846) from the TOWER BRACE, LOWER CROSS SUPPORT, and BENCH FRAME. See FIGURE 1.
(NOTE: It may be necessary to loosen and remove some pulleys before removing the cable.)
•
•
Discard CABLE (67846).
Remove the SHROUD from TOWER for ease of assembly.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3
6
FIGURE 2
STEP 2:
• Snap two WEIGHT PLATE BUSHINGS (3) into the top of all five WEIGHT PLATES (6) as shown in FIGURE 2.
FIGURE 3
TOWER
TOWER
BRACE
1/2 X 4” BOLT
(EXISTING)
GUIDE
RODS
SHAFT
COLLARS
STEP 3:
•
Remove two 1/2 X 4” BOLTS, two 1/2” WASHERS, and two 1/2” LOCK NUTS from the TOWER BRACE to remove the TOWER
BRACE from the TOWER and GUIDE RODS as shown in FIGURE 3.
•
LOOSEN the SHAFT COLLAR SET SCREWS and slide them off the GUIDE RODS.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
3
4
4
5
2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4:
•
Tilt the GUIDE RODS back and remove the HEAD PLATE
ASSEMBLY, and the twenty WEIGHT PLATES.
•
Unbolt the old WEIGHT STACK SHAFT from the HEAD
PLATE and replace it with the new 25 HOLE WEIGHT
STACK SHAFT (1). (NOTE: The bolt hole in the HEAD
PLATE should be on top. Please discard the old WEIGHT
STACKSHAFT.)
HEADPLATE
TOWER
•
•
Attach the WEIGHT STACK LABELS (4) (#’s 220-260) or
(5) (21-25) to the five WEIGHT PLATES (2) as shown on
FIGURE 4.
GUIDEROD
1
Insert the two GUIDE RODS through the two WEIGHT
STACK CUSHIONS into the base of the TOWER as
shown in FIGURE 4. Lubricate the GUIDE RODS with a
silicon or teflon spray that is available at most hardware
stores.
•
USING EXTREME CARE, slide the five new WEIGHT
PLATES (6) and the previous twenty WEIGHT PLATES
down over the GUIDE RODS onto the WEIGHT STACK
CUSHIONS. (NOTE: Make sure that the key holes of the
WEIGHT PLATES all face the same way.)
6
5
4
• Carefully Slide the new HEAD PLATE ASSEMBLY down
over the GUIDE RODS onto the weight stack as shown in
FIGURE 4.
WEIGHT
STACK
CUSHION
FIGURE 4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5
TOWER
TOWER
BRACE
1/2 X 4” BOLT
(EXISTING)
GUIDE
RODS
SHAFT
COLLARS
STEP 5:
•
Place TOWER BRACE over the GUIDE RODS and securely fasten TOWER BRACE to TOWER using previously removed 1/2” X 4”
BOLTS, 1/2” WASHERS, AND 1/2” NUTS as shown in FIGURE 5.
•
Slide the SHAFT COLLARS to the top of the GUIDE RODS andSECURELY tighten the SHAFT COLLAR SET SCREWS .
TOWER
2
SHROUD
FIGURE 6
STEP 6:
•
Route threaded end of newCABLE (68127) (2) around pulleys in TOWER BRACE, LOWER CROSS SUPPORT, and BENCH
FRAME as shown in FIGURE 6.
• Retighten any loosened pulley connections.
Reassemble SHROUD to the TOWER.
•
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2
1
FIGURE 7
STEP 7:
•
•
•
Screw the threaded end of the newCABLE (68127) (2) approximately 3/4” into the end of the WEIGHT STACK SHAFT (1) and
tighten jam nut securely.
If the HEAD PLATE does not sit on top of the first WEIGHT PLATE, push the head plate down, insert the SELECTOR PIN and
perform several repetitions on the machine. This will relax the cable system and prevent the HEAD PLATE from lifting up.
If after completing the previous step, the HEAD PLATE still does not sit on top of the first WEIGHT PLATE or if there is excess
slack in the cable system, adjust the threaded end of the CABLE accordingly and retighten the jam nut.
Thank you for purchasing the LifeFitness 8216 50 LB. ADD-ON KIT. If unsure of proper use of equipment, call your local
LifeFitness distributor or call the LifeFitness customer service department at (800) 328-9714.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|