G7 CABLE MOTION
™
GYM SYSTEM
ASSEMBLY INSTRUCTIONS
G7-002 / CLASS H / 10/14/08 / 8352100 REV. B
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
1. DO NOT use or permit use of any equipment that is damaged and or has worn or broken parts. For all
LIFE FITNESS equipment use only replacement parts supplied by LIFE FITNESS.
2. Cables and Belts pose an extreme liability if used when frayed. Always replace any cable at first sign of
wear (consult LIFE FITNESS if uncertain).
3. Routinely inspect all accessory clips that join attachments to the cables and replace at the first sign of
wear.
4. MAINTAIN LABELS AND NAMEPLATES - Do not remove labels for any reason. They contain important
information. If unreadable or missing, contact LIFE FITNESS for a replacement.
5. EQUIPMENT MAINTENANCE - Preventative maintenance is the key to smooth operating equipment as
well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals.
6. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is
qualified to do so. LIFE FITNESS will provide service and maintenance training at our corporate facility
upon request or in the field if proper arrangements are made.
7. Before any use, examine all accessories approved for use with the LIFE FITNESS equipment for
damage or wear.
8. DO NOT ATTEMPT TO USE OR REPAIR ANY ACCESSORY APPROVED FOR USE WITH THE LIFE
FITNESS EQUIPMENT WHICH APPEARS TO BE DAMAGED OR WORN.
OPERATING WARNINGS
1. It is the purchaser's sole responsibility to properly instruct its end users and supervising personnel as to
the proper operating procedures of all LIFE FITNESS equipment.
2. Keep children away from strength equipment. Parent or others supervising children must provide close
supervision of children if the equipment is used in the presence of children.
3. Do not allow users to wear loose fitting clothing or jewelry while using equipment. It is also
recommended to have user's secure long hair back and up to avoid contact with moving parts.
4. All bystanders must stay clear of all users, moving parts and attached accessories and components
while machine is in operation.
SELECTORIZED WEIGHT STACK SYSTEMS
1. Use only weight selector pins supplied by LIFE FITNESS on weight stacks. Substitutes are forbidden.
2. Fully insert weight selector pins. Partial insertion can cause weights to fall unexpectedly.
3. Never pin the weight stack in an elevated position.
4. Never remove selector pin if any weights are suspended.
5. Never attempt to release jammed weights or parts.
6. Never use dumbbells or other means to incrementally increase the weight resistance. Use only those
means provided by LIFE FITNESS.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
G7 WARNING LABELS
Schiller Park, IL
Model: FZCP-
www.lifefitness.com
Serial Number:
Class: S - Studio
Maximum User Weight: 300 lbs (136kg)
NOTE: Lock the weight stack when not using the gym. Make sure all the weight plates are resting on the plate below
with no gap in between. Insert the weight selector pin in the tab underneath the weight stack. The weight selector pin
should be inserted until the knob touches the metal tab. Once the pin goes through the weight stack system, the weight
stack becomes immobile. Verify that the pin has gone through the weight stack stem.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GYM DIMENSIONS
Weight:
Resistance Ratio: 1:2
Weight Stack: 160 lbs
720 lbs
5
Download from Www.Somanuals.com. All Manuals Search And Download.
G7 LIVE AREA
12”
12”
10’
18’-8”
NOTE: The live area shows the extent of the G7 gym. It does not include the user.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS LIST
ITEM NO.
QTY.
DESCRIPTION
1
1
LEFT TOWER
2
1
1
1
1
1
1
1
1
1
1
1
16
4
4
4
30
2
2
4
2
2
2
6
1
2
4
1
1
2
1
1
1
1
2
2
1
1
1
1
1
1
1
TOP BRACKET TUBE
MIDDLE BRACKET TUBE
BOTTOM BRACKET TUBE
LEFT SLIDE TUBE (WITH ROLLER CARRIAGE) ASSEMBLY
RIGHT U BRACKET
LEFT U BRACKET
RIGHT SWIVEL PULLEY
LEFT SWIVEL PULLEY
RIGHT SLIDE TUBE (WITH ROLLER CARRIAGE) ASSEMBLY
RIGHT TOWER
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
60
CHIN UP BAR
PULLEY
PARTIAL PULLEY COVER
GUIDE ROD RETAINER
GUIDE ROD ASSEMBLY
10 LB WEIGHT PLATE
TOP PLATE
HEAD PLATE PULLEY ASSEMBLY
WEIGHT STACK CUSHION
CABLE
FOOT EXTENSION
SIDE SHROUD
KIOSK BRACKET
KIOSK ASSEMBLY
WEIGHT PIN & RING
FULL PULLEY COVER
LEFT ROLLER CARRIAGE
RIGHT ROLLER CARRIAGE
D RINGS
THIGH STRAP
FOOT STRAP
TOWEL
MARKER
HANDLES
SNAP LINKS
DVD
TOUCH-UP PAINT
EXERCISE BALL
PUMP
LONG BAR
WATER BOTTLE
EXERCISE BOOKLET
7
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS LIST
HARDWARE
ITEM NO.
QTY.
DESCRIPTION
43
32
M10 X 20MM SCREW
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
58
20
20
4
M10 WASHER
M5 HEX SCREW
M6 WASHER
M10 X 55MM SCREW
M10 X 45MM SCREW
M10 HEX NYLOCK NUT
M10 X 70MM SCREW
M10 SOCKET HEAD NUT
M10 X 50MM SCREW
PULLEY RETAINER
RETAINER RING
2
13
7
2
2
2
4
4
M10 X 50MM HEX TENSION SCREW
M5 SHOULDER SCREW
M10 X 16MM SCREW
M10.5 WASHER
32
12
12
2
.500-13 JAM NUT
BLISTER PACKS
Blister Pack 7-1
Blister Pack 7-2
Blister Pack 7-3
Blister Pack 7-4
Blister Pack 7-5
Blister Pack 7-6
1
1
1
1
1
1
REQUIRED TOOLS
ADJUSTABLE WRENCH
EXTERNAL SNAP RING PLIERS
PHILLIPS SCREW DRIVER
ALLEN WRENCHES (4mm, 5mm, 7mm)
WRENCH (17mm)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE:
M5 HEX SCREW (#45)
M10 X 20MM SCREW (#43)
M10 WASHER (#44)
M10 X 55MM SCREW (#47)
M6 WASHER (#46)
M10 X 45MM SCREW (#48)
M10 HEX NYLOCK NUT (#49)
M10 SOCKET NUT (#51)
M10 X 50MM SCREW (#52)
M10 X 70MM SCREW (#50)
M10 X 50MM HEX TENSION SCREW (#55)
PULLEY RETAINER (#53)
RETAINER RING (#54)
M5 SHOULDER SCREW (#56)
M10 X 16MM SCREW (#57)
M10.5 WASHER (#58)
Centimeters
M6 JAM NUT (#59)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2
43 44
3
44 43
1
11
1
A
B
4
11
43 44
44 43
NOTE: Two person assembly is recommended.
STEP 1:
Use the following hardware contained in Blister Pack (7-1):
ꢀ
M10 x 20mm SCREW (Qty. 24)
M10 WASHER (Qty. 24)
ꢀ
ꢁ Make sure the LEFT TOWER (1) and the RIGHT TOWER (11) are positioned correctly prior to assembly. The LEFT
U BRACKET (A) and RIGHT U BRACKET (B) should point towards each other as shown in the above illustration.
ꢁ Use four M10 x 20mm SCREWS (43) and four M10 WASHERS (44) to connect the BOTTOM BRACKET TUBE (4)
to the LEFT TOWER (1). Finger tighten only.
NOTE: THE BOTTOM BRACKET TUBE (4) HAS A RUBBER PAD ATTACHED TO IT TO MAKE CONTACT WITH THE
FLOOR.
ꢁ Repeat the above process using the TOP BRACKET TUBE (2) and the MIDDLE BRACKET TUBE (3).
NOTE: THE TOP BRACKET TUBE (2) DOES NOT HAVE ANY HOLES. THE MIDDLE BRACKET TUBE (3) HAS
THREE HOLES THROUGH THE TOP AND BOTTOM.
ꢁ Repeat all of the above steps to attach the TOP (2), MIDDLE (3), and BOTTOM (4) BRACKET TUBES to the RIGHT
TOWER (11).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
50
44
50
44
44
49
11
1
12
STEP 2:
Use the following hardware contained in Blister Pack (7-1):
ꢀ
ꢀ
ꢀ
M10 x 70mm SCREW (Qty. 4)
M10 WASHER (Qty. 8)
M10 HEX NYLOCK NUT (Qty. 4)
ꢁ Attach the CHIN UP BAR (12) between the LEFT TOWER (1) and RIGHT TOWER (11) using four M10 x 70mm
SCREWS (50), eight M10 WASHERS (44), and four M10 HEX NYLOCK NUTS (49). Finger tighten only.
NOTE: Make sure the CHIN UP BAR (12) is in the correct position as shown.
ꢁ Tighten all FRAME and CHIN UP BAR screws and nuts securely.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
49
44
C
44
48
28
11
10
5
1
29
49
44
D
44
47
STEP 3:
Use the following hardware contained in Blister Pack (7-2):
ꢀ
ꢀ
ꢀ
ꢀ
M10 x 45mm SCREW (Qty. 2)
M10 WASHER (Qty. 8)
M10 HEX NYLOCK NUT (Qty. 4)
M10 x 55mm SCREW (Qty. 2)
ꢁ Slide the top of the LEFT SLIDE TUBE ASSEMBLY (5) over the UPPER BRACKET (C) on the LEFT TOWER (1).
NOTE: MAKE SURE THE ENGRAVED NUMBERS ON THE LEFT SLIDE TUBE ASSEMBLY (5) FACE THE INSIDE
OF THE GYM. NOTE THE ORIENTATION OF THE CARRIAGE.
ꢁ Secure the LEFT SLIDE TUBE ASSEMBLY (5) to the UPPER BRACKET (C) of the LEFT TOWER (1) using one
M10 x 45mm SCREW (48), two M10 WASHERS (44), and one M10 HEX NYLOCK NUT (49). Do not tighten at
this time.
ꢁ Secure the LEFT SLIDE TUBE ASSEMBLY (5) to the LOWER BRACKET (D) of the LEFT TOWER (1) using one
M10 x 55mm SCREW (47), two M10 WASHERS (44), and one M10 HEX NYLOCK NUT (49).
ꢁ Repeat the above process to secure the RIGHT SLIDE TUBE ASSEMBLY (10) to the RIGHT TOWER (11). Tighten
all nuts and screws securely.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
11
56
1
23
F
E
45
46
6
7
STEP 4:
Use the following hardware contained in Blister Pack (7-2):
ꢀ
ꢀ
ꢀ
M5 SHOULDER SCREW (Qty. 32)
M5 HEX SCREW (Qty. 8)
M6 WASHER (Qty. 8)
ꢁ Remove the protective paper from the SIDE SHROUD (23) before installation.
ꢁ Install one SIDE SHROUD (23) to the RIGHT TOWER (11) using sixteen M5 SHOULDER SCREWS (56) on the
inside of the SIDE SHROUD (23) into the UPRIGHT TUBES (E) of the RIGHT TOWER (11). Tighten the screws
securely.
NOTE: YOU MUST BE STANDING INSIDE THE GYM TO INSTALL THE SIDE SHROUD (23).
ꢁ Repeat this process for installing one SIDE SHROUD (23) to the LEFT TOWER (1).
ꢁ Attach the RIGHT U BRACKET (6) onto the back of the UPRIGHT TUBE (E) of the RIGHT TOWER (11) using four
M5 HEX SCREWS (45) and four M6 WASHERS (46). Tighten the screws securely.
ꢁ Repeat this process for installing the LEFT U BRACKET (7) onto the back of the UPRIGHT TUBE (F) of the LEFT
TOWER (1).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
55
15
54
16
19
59
26
18
17
NOTE: The Side Shroud is not shown in
this illustration for clarity.
G
11
20
STEP 5:
Use the following hardware contained in Blister Pack (7-3):
ꢀ
ꢀ
ꢀ
M10 x 50mm HEX TENSION SCREW (Qty. 4)
GUIDE ROD RETAINER (Qty. 4)
RETAINER RING (Qty. 4)
NOTE: INSTALL FROM THE INSIDE OF THE UNIT.
ꢁ Position two WEIGHT STACK CUSHIONS (20) and GUIDE RODS (16) at the GUIDE ROD BRACKET (G) on the
RIGHT TOWER (11) as shown.
NOTE: MAKE SURE THAT THE PLUGGED END OF THE GUIDE RODS (16) ARE FACING UP.
ꢁ Slide one WEIGHT PLATE (17) over the GUIDE RODS (16) and slowly lower the WEIGHT PLATE (17) onto the
WEIGHT STACK CUSHIONS (20).
ꢁ Continue stacking a total of fifteen WEIGHT PLATES (17).
ꢁ Slide one TOP PLATE (18) over the GUIDE RODS (16) and slowly lower it onto the WEIGHT PLATES (17).
ꢁ Slide one WEIGHT PIN with RING (26) over the stem of the TOP PLATE (18).
ꢁ Thread the HEAD PLATE PULLEY ASSEMBLY (19) into the TOP PLATE (18). Do not tighten! This will be adjusted
later. Make sure the JAM NUT (59) is threaded onto the HEAD PLATE PULLEY ASSEMBLY (19) before threading
into the TOP PLATE (18).
ꢁ Slide one RETAINER RING (54) over each of the GUIDE RODS (16).
ꢁ Thread an M10 x 50mm HEX TENSION SCREW (55) into each of the two GUIDE ROD RETAINERS (15). Do not
fully thread the M10 x 50mm HEX TENSION SCREWS (55) into the GUIDE ROD RETAINERS (15).
ꢁ Slide the GUIDE ROD RETAINERS (15) into the holes on the RIGHT TOWER (11). Make sure the M10 x 50mm
HEX TENSION SCREWS (55) in the GUIDE ROD RETAINERS (15) are facing up.
ꢁ Push the GUIDE ROD RETAINERS (15) up high enough so that the GUIDE RODS (16) can be placed under
them.
ꢁ Lower the GUIDE ROD RETAINERS (15) over the GUIDE RODS (16).
ꢁ Slide the RETAINER RINGS (54) up. Use a RETAINING RING PLIER to secure the RETAINER RINGS (54) into
the groove on the GUIDE ROD RETAINERS (15). If the groove is hidden inside the hole on the tube, use a 5mm
ALLEN WRENCH to loosen the M10 x 50mm HEX TENSION SCREW (55) until the groove is accessible.
ꢁ Repeat this step to complete the LEFT TOWER assembly.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
52
53
14
13
14
51
Upper Pulley
13
Lower Pulley
49
44
44
48
STEP 6:
ꢁ Uncoil the cables to remove all twists.
ꢁ Remove the (UPPER) PULLEYS (13) on the RIGHT TOWER (11) and LEFT TOWER (1) by removing the M10 x
50mm SCREW (52), PULLEY RETAINER (53), M10 SOCKET HEAD NUT (51), and PARTIAL PULLEY COVERS
(14). Set the (UPPER) PULLEYS (13) and hardware aside.
ꢁ Remove the (LOWER) PULLEYS (13) on the RIGHT TOWER (11) and LEFT TOWER (1) by removing the M10 x
45mm SCREW (48), two M10 WASHERS (44), and M10 HEX NYLOCK NUT (49).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Middle Upper Pulley
2
3
13
Upper Pulley
21
52
53
14
H
29
13
14
51
Upper Pulley
59
38
53
27
Middle Upper Pulley
13
27
19
51
13
Lower Pulley
STEP 7:
Use the following hardware contained in Blister Packs (7-3), (7-4) and (7-5):
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
M10 WASHER (Qty. 4)
M10 HEX NYLOCK NUT (Qty. 2)
M10 x 45mm SCREW (Qty. 2)
M10 SOCKET HEAD NUT (Qty. 2)
M10 x 50mm SCREW (Qty. 2)
PULLEY RETAINER (Qty. 2)
ꢁ
ꢁ
Remove the JAM NUT (59) from the threaded end of the CABLE (21).
Lower the threaded end of the CABLE (21) down the long vertical tube that is in front of the gym until it can be retrieved near
where the (LOWER) PULLEY (13) was located. Carefully pull enough cable out to reach the RIGHT ROLLER CARRIAGE (29).
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
INSTALL the (LOWER) PULLEY (13) using the M10 x 45mm SCREW (48), two M10 WASHERS (44), and M10 HEX NYLOCK
NUT (49). Be sure that the CABLE (21) is properly routed around the (LOWER) PULLEY (13).
Bring the threaded end of the CABLE (21) up to the RIGHT ROLLER CARRIAGE (29) and thread the CABLE (21) into the
RIGHT ROLLER CARRIAGE (29). Do not tighten!
Assemble the (MIDDLE UPPER) PULLEY (13) by using two FULL PULLEY COVERS (14), one PULLEY RETAINER (53), one
M10 SOCKET HEAD NUT (51) and one M10 x 50mm SCREW (52).
Feed the cable end with the small ball between the MIDDLE UPPER PULLEY BRACKET (H) and then through the forward most
hole in the MIDDLE BRACKET TUBE (3) above the HEAD PLATE PULLEY ASSEMBLY (19).
Take the CABLE (21) down and around the HEAD PLATE PULLEY (19) and back up through the MIDDLE BRACKET TUBE (3)
again, passing through the remaining access hole.
Feed the CABLE (21) around where the (UPPER) PULLEY (13) of the RIGHT TOWER (11) was located. Forward the CABLE
(21) through the TOP BRACKET TUBE (2) and out the access hole where the (UPPER) PULLEY (13) was located.
REINSTALL the (UPPER) PULLEY (13) using the previously removed M10 x 50mm SCREW (I), PULLEY RETAINER (J), M10
SOCKET HEAD NUT (K), and PARTIAL PULLEY COVER (L). Be sure that the CABLE (21) is properly routed around the PUL-
LEY.
ꢁ
ꢁ
ꢁ
Bring the CABLE (21) down to the RIGHT ROLLER CARRIAGE (29).
Feed the CABLE (21) through the two pulleys in the RIGHT ROLLER CARRIAGE (29) as shown.
Repeat Step 6 to route the cable through the LEFT TOWER (1).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
QTY
DESCRIPTION
I
1
1
1
1
2
QUICK CONNECT COUPLER
QUICK CONNECT HOUSING
QUICK CONNECT SLEEVE
QUICK CONNECT SPRING
M5 HEX SCREW
J
K
L
I
M
K
L
J
M
Cable
Slide Mechanism to insert
or Exchange Handles
K
STEP 8:
ꢁ Dissemble one QUICK CONNECT by removing the two M5 HEX SCREWS (M) from the QUICK CONNECT COU-
PLER (I). Carefully remove the QUICK CONNECT SPRING (L), the QUICK CONNECT SLEEVE (K) and the QUICK
CONNECT HOUSING (J).
ꢁ Slide the QUICK CONNECT HOUSING (J), QUICK CONNECT SPRING (L), and QUICK CONNECT SLEEVE (K)
onto the cable as shown. Insert the cable end into the QUICK CONNECT COUPLER (I).
ꢁ Slide the entire assembly over the QUICK CONNECT COUPLER (I). Attach the QUICK CONNECT COUPLER (I) and
QUICK CONNECT HOUSING (J) together. Use the two M5 HEX SCREWS (M) to tighten.
NOTE: IF NECESSARY, ENSURE CABLES ARE PROPER LENGTH; MAKE NECESSARY ADJUSTMENTS TO THE
WEIGHT STACK PULLEY (TIGHTEN OR LOOSEN); THREAD THE END OF THE CABLE; AND REMOVE THE PUL-
LEY FROM THE HOUSING AND SPIN CLOCKWISE OR COUNTER CLOCKWISE TO LOOSEN/TIGHTEN.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
28
19
18
21
STEP 9:
ꢁ Make adjustments to the HEAD PLATE PULLEY (19) and the threaded cable end to adjust cable length and to
ensure the cable is taut.
ꢁ If the threaded cable end is completely threaded into the LEFT ROLLER CARRIAGE (28) and there is still some
slack in the CABLE (21), remove the pulley from the HEAD PLATE PULLEY (19). Thread the HEAD PLATE PULLEY
(19) further into the TOP PLATE ASSEMBLY (18) and reinstall the pulley.
ꢁ Once the CABLE (21) is taut, engage the jam nut at the threaded end of the cable as well as at the HEAD PLATE
PULLEY ASSEMBLY (19).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43 44
22
1
43
44
STEP 10:
Use the following hardware contained in Blister Pack (7-4):
ꢀ
M10 x 20mm SCREW (Qty. 8)
M10 WASHER (Qty. 8)
ꢀ
ꢁ Install one FOOT EXTENSION (22) to the bottom of the LEFT TOWER (1) using four M10 x 20mm SCREWS (43)
and four M10 WASHERS (44).
ꢁ Repeat the above step to attach the other FOOT EXTENSION (22) to the bottom of the RIGHT TOWER (11).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
25
3
3
50
44
44
49
25
46
45
58
57
24
11
STEP 11:
Use the following hardware contained in Blister Pack (7-6):
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
M5 HEX SCREW (Qty. 12)
M6 WASHER (Qty. 12)
M10 x 16mm SCREW (Qty. 12)
M10.5 WASHER (Qty. 12)
M10 x 70mm SCREW (Qty. 3)
M10 WASHER (Qty. 6)
M10 HEX NYLOCK NUT (Qty. 3)
ꢁ Attach the six KIOSK BRACKETS (24) to the RIGHT TOWER (11) and LEFT TOWER (1) using two M5 HEX
SCREWS (45) and two M6 WASHERS (46) each. Tighten the screws securely.
ꢁ Fasten the KIOSK (25) to the KIOSK BRACKETS (24) using twelve M10 x 16mm SCREWS (57) and twelve M10.5
WASHERS (58).
NOTE: SUPPORT THE KIOSK (25) UNTIL THE SCREWS ARE INSTALLED.
ꢁ Secure the top of the KIOSK (25) to the MIDDLE BRACKET TUBE (3) using three M10 x 70mm SCREWS (50), six
M10 WASHERS (44), and three M10 HEX NYLOCK NUTS (49).
NOTE: THE TOP OF THE KIOSK (25) HAS THREE SLOTS THAT FIT UNDERNEATH THE THREE HOLES OF THE
MIDDLE BRACKET TUBE (3).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
O
28
O
N
P
STEP 12:
ꢁ Adjust the rollers if the ROLLER CARRIAGE (28) rolls up and down the tube with difficulty, or if it seems to sloppy.
ꢁ Unscrew the cable end from the roller carriage housing.
ꢁ Remove the SCREWS (N) that hold the two PLASTIC COVERS (O) together.
ꢁ There are two ROLLER ADJUSTMENT SCREWS (P), each with a spring, on the back side of the roller carriage
housing. The roller drag can be increased/decreased by adjusting these screws.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
36
35
31
32
41
STEP 13:
ꢁ
The G7 comes with the following accessories: THIGH STRAP (31), FOOT STRAP (32), HANDLES (35), SNAP
LINKS (36), LONG BAR (41), and EXERCISE BALL (39).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
R
S
Q
STEP 14:
ꢁ
Use the FRONT HANDLE (Q) to tilt the bench.
ꢁ Steer the bench to align with the U BRACKETS (R).
ꢁ Insert one PIN (S) into each bracket so the bench is restrained.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Please note:
* We recommend cleaning your product (pads and frame) on a regular basis, using
warm soapy water. Touch-up paint can be purchased from your Life Fitness cus-
tomer service representative at (800) 351-3737.
* Inspect equipment before each use. Tighten all loose connections are replace worn
parts immediately. Failure to do so may result in serious injury.
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD ON-LINE
AT WWW.LIFEFITNESS.COM.
Model #:
_____________________________________
_____________________________________
Serial #'s:
(Note: The Model/Serial label is located on the back side of the UPRIGHT TUBE of the LEFT TOWER)
Date of Purchase: _____________________________________
Dealer’s Name
_____________________________________
Dealer’s Phone# _____________________________________
Thank you for purchasing the Life Fitness
G7 CABLE MOTION GYM SYSTEM
24
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Life Fitness® G7 Cable Motion™ Gym System
Life Fitness extends the following LIMITED WARRANTY to the original owner (proof of purchase required, keep your
receipt with this manual) of the Life Fitness product. The Warranty terms apply to IN HOME and LIGHT INSTITUTIONAL
USE ONLY.
1.
LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the Life Fitness product or a weld should crack
or break, it will be repaired or replaced by Life Fitness. Terms: IN HOME USE ONLY: Lifetime – for so long as the
Customer owns the Life Fitness product; LIGHT INSTITUTIONAL USE: Ten (10) years.
2.
LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, Life Fitness will
supply replacement parts: all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retain-
ing clips, adjustable pre-stretch slides, roller pad shafts, allen head bolts, weight selector pin, weight stack shaft,
set screws, protector caps, adjustment chain, cotter pin, plunger, spring and knob. Terms: IN HOME USE ONLY:
Lifetime – for so long as the Customer owns the Life Fitness product; LIGHT INSTITUTIONAL USE: One (1) year.
3.
4.
5.
LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in mate-
rial or workmanship, Life Fitness will repair or replace them, at its option. Terms: IN HOME USE ONLY: Three (3)
years; LIGHT INSTITUTIONAL USE: Ninety (90) days.
CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person
other than an authorized Life Fitness Service Center, any improper assembly, accident, or any other condition
resulting from occurrences beyond the control of Life Fitness will void this Limited Warranty.
REPLACEMENT AND REPAIR EXPENSES. Life Fitness will provide only replacement parts or repair under this
warranty. The Owner is responsible for all other costs. Such costs may include, but are not limited to: a. labor
charges for service, removal, repair or reinstallation of the Life Fitness product or any component part; b. shipping,
delivery, handling and administrative charges for returning parts to Life Fitness; and c. all necessary or incidental
costs related to installation of the replacement parts.
6.
7.
SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of Life Fitness), parts should be
shipped in their original carton or equivalent packaging, fully insured with shipping charges prepaid. Life Fitness
will not assume any responsibility for any loss or damage incurred in shipping.
CLAIM PROCEDURES. If service on your Life Fitness product is required during the warranty period, please con-
tact our Customer Service Department at 1-800-351-3737 (U.S. and Canada) or +1-847-288-3300 (outside of U.S.
and Canada) for instructions regarding returning or replacing parts. Please have available the following informa-
tion: (i) the dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product(s) (the serial number loca-
tion is called out on the final assembly drawing included with your assembly instruction); (iv) a description of the
nature of the problem.
8.
9.
OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which
vary depending on local law.
LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law,
shall have no greater duration than the warranty period set forth above. There are no warranties which extend
beyond the description in this Limited Warranty. Because local laws do not allow limitations on how long an implied
warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of Life Fitness with respect to
any Life Fitness product or the operation, repair or replacement of any Life Fitness product. Life Fitness shall not
be responsible for injury, loss of use of the Life Fitness product, inconvenience, loss or damage to personal prop-
erty, whether direct or indirect, and incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
Notes:
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CORPORATE HEADQUARTERS
5100 North River Road
Schiller Park, Illinois 60176 • U.S.A.
847.288.3300 • FAX: 847.288.3703
800.735.3867 (Toll-free within U.S.A., Canada)
INTERNATIONAL OFFICES
Austria
Life Fitness Austria
AMERICA’S
ASIA PACIFIC (AP)
Japan
North America
Vertriebs G.m.b.H.
Life Fitness Japan
Life Fitness Inc.
Dückegasse 7-9/3/36
1220 Vienna
AUSTRIA
Telephone: (+43) 1.61.57.198
Fax: (+43) 1.61.57.198.20
Nippon Brunswick Bldg., #8F
5-27-7 Sendagaya
Shibuya-Ku, Tokyo
Japan 151-0051
Telephone: (+81) 3.3359.4309
Fax: (+81) 3.3359.4307
5100 N River Road
Schiller Park, IL 60176 U.S.A
Telephone: (847) 288 3300
Fax: (847) 288 3703
Spain
Life Fitness IBERIA
Brazil
Life Fitness Do Brazil
China and Hong Kong
Life Fitness Asia Pacific LTD
C/Frederic Mompou 5,1º1ª
08960 Sant Just Desvern Barcelona
SPAIN
Telephone: (+34) 936 724 660
Fax: (+34) 936 724 670
Av. Dr. Dib Sauaia Neto 1478
Alphaville, Barueri, SP
06465-140
BRAZIL
Telephone: (800) 773 8282
Fax: (+55) 11.4133.2893
Room 2610, Miramar Tower
132 Nathan Road
Tsimshatsui, Kowloon
HONG KONG
Telephone: (+852) 2891.6677
Fax: (+852) 2575.6001
Italy
Life Fitness ITALIA S.R.L.
Latin America & Caribbean*
Life Fitness Inc.
Via Crivellin 7/N
37010 Affi Verona
ITALY
All Other Asia Pacific countries &
distributor business Asia Pacific*
5100 N River Road
Schiller Park, IL 60176 U.S.A
Telephone: (847) 288 3300
Fax: (847) 288 3703
Telephone: (+39) 045.7237811
Fax: (+39) 045.7238197
Room 2610, Miramar Tower
132 Nathan Road
Tsimshatsui, Kowloon
HONG KONG
Telephone: (+852) 2891.6677
Fax: (+852) 2575.6001
Belgium
Life Fitness Benelux NV
EUROPE, MIDDLE EAST, & AFRICA
(EMEA)
Parc Industrial de Petit-Rechain
4800 Verviers
BELGIUM
Telephone: (+32) 87 300 942
Fax: (+32) 87 300 943
Netherlands & Luxemburg
Life Fitness Atlantic BV
Bijdorpplein 25-31
2992 LB Barendrecht
THE NETHERLANDS
Telephone: (+31) 180 646 666
Fax: (+31) 180 646 699
All Other EMEA countries &
distributor business C-EMEA*
Bijdorpplein 25-31
2992 LB Barendrecht
THE NETHERLANDS
Telephone: (+31) 180 646 666
Fax: (+31) 180 646 699
United Kingdom & Ireland
Life Fitness UK LTD
Queen Adelaide
Ely, Cambs, CB7 4UB
Telephone: General Office (+44) 1353.666017 Customer
Support (+44) 1353.665507
Fax: (+44) 1353.666018
Germany & Switzerland
Life Fitness Europe GMBH
Siemensstrasse 3
85716 Unterschleissheim
GERMANY
Telephone: (+49) 89.31 77 51.0 (Germany)
(+41) 0848 000 901 (Switzerland)
Fax: (+49) 89.31 77 51.99 (Germany)
(+41) 043 818 07 20 (Switzerland)
G7-002 Rev A
10/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|