Liebherr Beverage Dispenser EWTNes 2956 User Manual

Installation  
Instructions  
41  
64  
0
Up  
Down  
On/Off  
SuperFrost  
Alarm  
On/Off  
Light  
Zone  
Up  
Down  
For wine cooler with  
NoFrost freezer compartment and  
Side-By-Side Units  
with IceMaker  
Instructions  
de montage  
Armoire de mise en température des  
vins avec congélateur NoFrost et les  
appareils côte à côte  
2
-
-
6
4
8
avec IceMaker  
6
-12  
4
2
4
6
-
-
6
8
Instrucciones  
de instalación  
-12  
3
2
4
6
-
-
6
8
Armario de acondicionamiento de  
vinos con congelador NoFrost y  
unidades lado a lado  
-12  
2
2
4
6
-
-
6
8
-12  
con IceMaker  
1
WF1051 / EWTNes 2956  
7082 410-00 3405  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT  
TO THE INSTALLER  
It is very important that the guidelines and  
instructions are followed in the manual to ensure  
proper installation and operation of the unit. The  
Installation Guidelines section contains important  
information for making sure the installation is  
correct. Read and understand all the information in  
Installation Guidelines, and in this manual before  
the unit is installed.  
A delight in freshness  
WF1051 / EWTNes 2956  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Contents  
Page  
Installation Guidelines................................................................................. 3  
Area Requirements............................................................................... 3  
Electrical Requirement.......................................................................... 3  
Customer’s Responsibility .................................................................... 3  
Blocking For Safety............................................................................... 3  
Unit Venting........................................................................................... 3  
Planning Information................................................................................... 4  
Cabinet Opening Dimensions............................................................... 4  
Reversing Door Hinges............................................................................... 9  
Door Opening Angle........................................................................... 12  
Installation................................................................................................. 13  
Blocking For Safety................................................................................... 16  
IceMaker.................................................................................................... 17  
Water Connection ............................................................................... 17  
Connection to the Water Supply......................................................... 18  
Side-By-Side Installation........................................................................... 20  
A delight in freshness  
WF1051 / EWTNes 2956  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION GUIDELINES  
Area Requirements  
Verify the following:  
WARNING  
!
ELECTROCUTION HAZARD  
• Floors can support refrigerator’s weight plus  
approximately 1200 pounds (544 kg) of food  
weight.  
Electrical Grounding Required. This  
appliance is equipped with a three-prong  
(grounding) polarized plug for your  
protection against possible shock hazards.  
• Finished kitchen floor height has to be level.  
Appliance must be shimmed to the floor level if  
the floor heights are not equal to make sure air  
vents are not obstructed.  
DO NOT remove the round grounding  
prong from the plug.  
DO NOT use a two-prong grounding  
adapter.  
DO NOT use an extension cord to  
connect power to the unit.  
• Remove anything attached to rear or side walls  
that can obstruct refrigerator opening.  
• Cutout dimensions are accurate.  
Customer’s Responsibility  
A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-  
side installation) fused electrical supply is required.  
We recommend using a dedicated circuit for this  
appliance to prevent electrical overload. Follow  
the National Electrical Code and local codes and  
ordinances when installing the receptacle.  
• Electrical outlet is in correct location.  
Do not install this unit next to any other refrigerator  
or freezer except another Liebherr model. Liebherr  
models are designed to allow side-by-side  
installation. They are equipped with a heating  
element to eliminate condensation when units are  
installed side by side. Installing this unit next to any  
other refrigerator or freezer can cause condensation  
or cause damage to the Liebherr unit.  
Blocking For Safety  
The anti-tip brackets must be installed to prevent  
the unit from tipping after it is installed. Refer to  
Blocking For Safety.  
Electrical Requirement  
Unit Venting  
If codes require a separate grounding circuit to be  
used, have a qualified electrician install the circuit.  
DO NOT restrict the air flow. Air flow must be  
provided for the unit to operate. The factory air  
vents provide 31 square inches (200 cm²) of air  
flow per unit. If you are replacing the factory air  
vents with an overlay, the air flow must be the  
same or greater than the factory air vents.  
WARNING  
!
Do not ground to a gas pipe. Check with a  
qualified electrician if you are not sure the  
appliance is properly grounded. Do not  
have a fuse in the neutral or grounding  
circuit.  
WARNING  
!
ELECTRICAL SHOCK HAZARD  
• Electrically ground refrigerator.  
• Do not use an extension cord.  
• Failure to follow these instructions  
could result in fire or electrical shock.  
A delight in freshness  
WF1051 / EWTNes 2956  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLANNING INFORMATION  
Cabinet Opening Dimensions -  
Figure 1  
Allow units to open a minimum of 90° to prevent  
problems removing drawers. With the door  
opening 90°, you may have to move drawers  
slightly to clear the door interior.  
Refer to the minimum door clearances in the Pre-  
Installation Specifications chart.  
• Allow for a minimum 3-3/4" (95 mm) filler, for  
corner installations, so the door can open to 90°.  
If you’re using raised panels, consider using a  
wider filler.  
IMPORTANT  
Refer to the full scale illustrations at the end  
of this section for specifics on door openings  
and filler size alternatives.  
3"  
"
(76mm)  
"
"
Figure 1  
A delight in freshness  
WF1051 / EWTNes 2956  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLANNING INFORMATION  
WF1051 - Figure 2  
Figure 2  
A delight in freshness  
WF1051 / EWTNes 2956  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLANNING INFORMATION  
Side-By-Side WF1051 and RB1400 - Figure 3  
Figure 3  
A delight in freshness  
WF1051 / EWTNes 2956  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLANNING INFORMATION  
The factory setting for the door to swing open  
is 130°. Use this illustration to ensure other  
cabinets or counters do not interfere with the  
door opening.  
130°  
A delight in freshness  
WF1051 / EWTNes 2956  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLANNING INFORMATION  
The optional setting for the door to swing  
open is 90°. Use this illustration to ensure  
other cabinets or counters do not interfere  
with the door opening.  
90°  
A delight in freshness  
WF1051 / EWTNes 2956  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSING DOOR HINGES  
The door hinges can be changed  
from one side to the other if  
required.  
5
1. Figure 4: Top: Unscrew the  
hinge pin (2) and remove the  
screw (5).  
2. Swivel out the door at the  
top, ensuring that you do not  
lose the stop (7) and bushing  
(8); lift off the door and place  
it on the floor. Unscrew the  
handle from the upper door  
2
5.  
14  
1.  
X
Y
2. 8  
2.  
7
A
and pull out the cover caps (A). Then screw  
the handle on the opposite side of the  
upper door and place the plugs (Y) in the  
open screw holes.  
3.  
9
W
3. Center: Pull out the hinge pin (9) with its  
washer.  
7
4.  
4. Swivel out the lower door, lift it out and  
place it on the floor. Take care not to lose  
the stop (7) and washers (8). Unscrew the  
handle from the lower door and pull out the  
plugs (A). Then screw the handle on the  
opposite side of the lower door and place  
the plugs (Y) in the open screw holes.  
5. Unscrew all the door fittings (14, 17) and  
remove plugs (W, X).  
8
W
Y
4.  
A
17  
5.  
X
Figure 4  
A delight in freshness  
WF1051 / EWTNes 2956  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSING DOOR HINGES  
6. Figure 5: Unscrew the lower hinge (13).  
- Remove the washer, stops and bushing (14, 7, 8).  
- Remove screw (Q).  
8. Unscrew the center hinge (10) and cover (11),  
pull them off to the side and after turning them  
through 180°, slide them on again on the  
opposite side and secure them.  
- Transfer hinge pin (2) to the opposite side.  
- Transfer screw (Q) to the opposite side.  
- Turn the stop (7) through 180° and position  
bushing (8) and washer as shown in the  
detailed drawing. The flat side of the stop must  
face forwards.  
9. Place the lower door on the hinge pin (2) at the  
bottom.  
- Swivel in the door.  
- Pay special attention to the bushing (12) in the  
center hinge (10).  
- Screw on hinge (13) on the new hinge side.  
- Insert the hinge pin (9).  
7. Install the door fittings as shown in Figure 5.  
Insert the plugs (X) as shown in the detailed  
drawing. Move plug (W) to the opposite side of  
the lower door.  
Figure 5  
A delight in freshness  
WF1051 / EWTNes 2956  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSING DOOR HINGES  
10. Figure 6: Lift up cover (3) on handle side, push  
12. Transfer hinge pin and screw to the respective  
opposite side of the hinge (4), but do not insert  
them in the hole or fasten them now.  
outward; lift up cover (1) on hinge side and pull  
off.  
11. Unscrew mounting plate (21): first mounting  
screw (20), then inner retaining screw (25).  
- Unscrew hinge (4): first remove the mounting  
screw (20), then retaining screws (25). Fit  
hinge (4) to opposite side: for easy assembly,  
fit hinge from above and first tighten with the  
upper retaining screw (25) M5, then screw  
(25) and finally mounting screw M4 (20).  
- Turn mounting plate (21) through 180° and  
screw tight again on the new handle side: first  
retaining screw (25), then mounting screw  
(20).  
13. On the upper door, install the door fittings as  
shown in Figure 6. Insert the plugs (X) as  
shown in the detailed drawing. Move plug (W)  
to the opposite side of the door.  
14. Place the upper door on the center hinge, fit the  
bushing (8), stop (7) and washer on the door,  
swivel in the door at the top and insert and  
secure the hinge pin (2) from above through the  
hinge and stop. Insert screw (6) for fixing the  
opening angle to 130°.  
Check for proper alignment of all doors. Adjust  
them if necessary using the slots on the hinge.  
W
Figure 6  
A delight in freshness  
WF1051 / EWTNes 2956  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSING DOOR HINGES  
Door Opening Angle - Figures 7, 8  
The appliance is delivered with a door opening  
angle of 130°.  
If the angle is to be decreased to 90°, proceed as  
follows:  
Insert attached screw (6) in the upper hinge as  
shown in Figure 7.  
Insert eccentric (Z) in the lower hinge as shown  
in Figure 8. Fix the eccentric with screw (V). The  
eccentric pin must point away from the hinge  
pin.  
6
Figure 7  
Q
V
Z
Figure 8  
A delight in freshness  
WF1051 / EWTNes 2956  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
Only install the winecooler/freezer in a stable  
kitchen cabinet that has been properly aligned.  
- Mount and fix the handles, depending on your  
model and choice.  
1.  
2
1
Unpacking  
Unpack the installation kit and check with the pro-  
vided parts list if all parts are included.  
3
2.  
The part numbers given in the parts list are identical  
to the numbers in the respective figures.  
4
6
4
5
For installation you will need the following tools:  
5
3.  
6 4  
5
Included:  
8
- Star Key Torx® 15  
- Star Key Torx® 20  
- Star Key Torx® 25  
- Socket Wrench 8 mm  
- Open-end Wrench 10 mm  
6
4
4.  
6 4  
5
Not in package:  
- Phillips (star) screwdriver  
- Level  
6
4
- Ruler  
Figure 16: Installation with Ventilation Grille Set:  
1. Screw the installation frame at the top (1) onto  
the appliance (2).  
5.  
2. Place the ventilation grille (3) on this, align  
it in the center and secure at the front from  
underneath.  
7
6.  
6.  
3. Slide brackets (4) onto the side installation  
7
frames (5) from above and below.  
4. Using the frame (5), screw the brackets onto  
the side wall*.  
7
5. Slide the side installation frames (5) upwards  
until they are in contact with the underside of  
the ventilation grille.  
7
6. Secure the side frames with the adhesive  
section (7) to prevent them from sliding down.  
Remove the protective film and affix the  
adhesive sections over the upper brackets on  
the handle and hinge sides.  
Figure 16  
A delight in freshness  
13  
WF1051 / EWTNes 2956  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
- Figure 17: Connect the appliance to the  
main power supply.  
- If the appliance is equipped with an  
IceMaker, establish the connection for  
the water supply. See “IceMaker, Water  
Connection”.  
1. Carefully slide the appliance into the cabinet  
until the ventilation grille touches the surrounding  
kitchen cabinet.  
2. Align the appliance until it is parallel with the sur-  
rounding kitchen cabinet. Use the open- end  
wrench 10 mm (3) to adjust the feet at the front.  
1.  
2.  
1
2
3
2
3
8 spanner  
2
3
10 spanner  
Figure 17  
Turn clockwise for up and counterclock-wise  
for down. For the rear use the adjusting  
bolt (2). Turn clockwise for down and counter-  
clockwise for up.  
3.  
Maximum adjustment: 19/64" (15 mm).  
1
2
3. Figure 18: Align the appliance at the side  
with the cabinet side panel and attach it with  
screws (1).  
- Cover the screws with cover caps (2).  
4. Fit the ventilation grille at the bottom [(3) if  
the door is hinged on the left, (4) if it is on the  
right]: Secure the ventilation grille so that it  
touches the floor and then adjust it using the  
slots.  
5
4.  
3
5
4
5
5
Figure 18  
A delight in freshness  
WF1051 / EWTNes 2956  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
The following ventilation cross-section and  
distances must be observed:  
At least 31 square inches (200cm2)  
- There must be a ventilation space of at  
least 31 square inches (200 cm²) per  
appliance in the cabinet plinth and under  
the cabinet top panel.  
- The depth of the ventilation duct at the  
rear of the cabinet must be at least 1-  
1/2" (38 mm).  
1.  
Alternatively:  
1. For built-in appliances without  
ventilation grilles and only with an  
installation frame, ventilation must take  
place through the ventilation duct at the  
rear of the cabinet.  
2
1
Built-in appliances with an installation frame:  
Figure 19:  
- Screw the complete installation frame (2)  
to the appliance.  
Figure 19  
2. Built-in appliances with a wooden  
ventilation grille:  
Figure 20: Cut out the wooden trim for use  
as a ventilation grille using the enclosed  
template.  
- The required ventilation cross-section  
must be at least 31 square inches  
(200 cm²) when a single appliance is  
installed, which corresponds to template  
“small” (If you install two appliances  
side-byside, the cross-section must be at  
least 62 square inches, (400 cm²), which  
corresponds to template “double-size;”  
for more information see “Side-by-Side  
Installation”).  
Remove the attachment bracket (2) from  
the installation frame and screw it to the  
appliance (1) from underneath. Place  
the wooden ventilation grille (5) on the  
appliance, align it in the center and secure  
it from the rear using the attachment  
bracket (2).  
2
1/2"  
5
(13 mm)  
1
24"  
(609.6 mm)  
3-11/16"  
(93,7 mm)  
Figure 20  
A delight in freshness  
WF1051 / EWTNes 2956  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BLOCKING FOR SAFETY  
IMPORTANT  
Figure 21: Secure the appliance in place so it does  
The anti-tip brackets can be installed in either  
direction or closer together. Always position  
the anti-tip brackets as wide apart as possible,  
but make sure they are anchored to two studs.  
not tip forward when the fully stocked door is  
opened.  
1. Measure the distance from the floor to the  
upper edge of the unit.  
5. Using the adjustable roller base, raise the unit  
until it makes contact with the brackets. Make  
sure the front levelers are firmly on the floor to  
prevent the appliance from tipping forward.  
2. Locate and mark two wall studs (1) against the  
wall where the appliance will be located. The  
space between the unit top and the bottom  
of the brackets must not be more than  
1/4" (6.4 mm).  
IMPORTANT  
3. Make sure the screws (2) extend a minimum of  
If your unit is positioned in between the  
wall studs, a board can be secured to the  
wall. Make sure the board is secured to the  
studs with screws that will penetrate into the  
studs a minimum of 1" (25.4 mm). The board  
should be a minimum of 1" x 6" (25.4 mm x  
152.4 mm) and long enough to secure both  
ends to the wall studs.  
1" (25.4 mm) into each of the wall studs.  
4. Make sure the anti-tip brackets (3) extend  
at least 3" (76.2 mm) over the unit and are  
securely in place.  
3
1
2
min 3"  
Figure 21  
A delight in freshness  
WF1051 / EWTNes 2956  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ICEMAKER  
Water Connection - Figure 22  
Please read the first three points of the safety  
instructions and warnings before connecting the  
appliance to the main water supply.  
• The water pressure must be between 21.8-  
87.0 psi (1.5-6 bar).  
Use a 1/4" OD copper line to connect the water  
supply to the solenoid valve. Allow extra length  
to the water supply line to provide slack for easy  
removal and to prevent the line from kinking.  
This is not supplied with the appliance  
(Figure 22).  
• A shut-off valve, such as the saddle valve  
illustration here, must be installed between the  
hose line and the main water supply so the  
water supply can be stopped if necessary.  
Figure 22  
• If you have hard water, we recommend you install  
a water softener. Also, a filter must be installed if  
the water contains solids such as sand.  
Do not install the shut-off valve behind the  
appliance.  
• All equipment and devices used to supply the  
water to the appliance must comply with the  
current regulations for your geographical area.  
A delight in freshness  
17  
WF1051 / EWTNes 2956  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ICEMAKER  
Connection to the Water Supply  
- Figures 23, 24  
1. Install the shut-off valve, water filter and  
automatic shut-off device as required.  
3. Open the shut-off valve for the water supply  
and check the entire water system for leaks.  
Before the appliance is used for the first time  
a licensed plumber should bleed air from the  
system.  
Note  
The solenoid valve is located at the rear of  
your unit.  
4. Insert the electrical plug for the combined  
winecooler/freezer into the electrical outlet  
(Figure 23).  
2. Place a 1/4" OD copper tubing between the  
shut-off valve and solenoid valve. Make sure  
there is approximately 30" (70 cm) of excess  
tubing behind the unit for easy connection.  
5. Move the combined winecooler-freezer into  
final position in the room.  
IMPORTANT  
The solenoid valve has a Metric R3/4 male  
connection.  
A R3/4(metric) to a 1/4" OD adapter and  
cable clip are supplied with the icemaker.  
Figure 24: Remove the cover cap (4) from  
the solenoid valve (1). Install the connection  
bracket (2) with sealing ring (6) on the  
solenoid valve (1). Attach the copper tube to  
the connection bracket (2). Secure the copper  
tube (3) to the appliance using the cable  
clip (5).  
Figure 23  
A delight in freshness  
18  
WF1051 / EWTNes 2956  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ICEMAKER  
1
4
1
6
2
3
5
5
Figure 24  
A delight in freshness  
WF1051 / EWTNes 2956  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
Figure 25: To install the WF1051 and RB1400  
Unpacking  
appliances side-by-side, proceed as follows:  
- Always place the WF1051 and RB1400 with  
the hinges on the left-hand side (looking from  
the front).  
Unpack the side by side installation kit and check  
with the provided parts list if all parts are included.  
The part numbers given in the parts list are identical  
to the numbers in the respective figures.  
Installation with SBS Ventilation Grille Set:  
For installation you will need the following tools:  
1. Affix the spacer (1) on the side wall of the  
Included:  
appliance – remove the protective film.  
- Star Key Torx® 15  
- Star Key Torx® 20  
- Star Key Torx® 25  
- Socket Wrench 8 mm  
- Open-end Wrench 10 mm  
2. Push the appliances together,  
- align them parallel to each other.  
3. Use a level on the top to align them to the same  
height:  
Not in package:  
- Phillips (star) screwdriver  
- Level  
4. Use the open-end wrench 10 mm (3) to adjust  
the feet at the front of the roller base. Turn  
clockwise for up and counterclockwise for down.  
For the rear, turn the adjusting bolt (2) clockwise  
down and counterclockwise up.  
- Ruler  
4.  
Figure 25  
A delight in freshness  
WF1051 / EWTNes 2956  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
5. Figure 26: Secure the installation frame (3) at  
5.  
2
3
the top to the appliances with screws (2).  
- Align the appliance at the front bottom.  
- Use the predrilled holes to align the installa-  
tion frame (2).  
- First mount the installation (3) frame with 4  
screws (2) to one appliance, then align the  
other appliance with the predrilled holes to  
the installation frame (3) and secure it with  
the screws (2).  
6. Figure 26: Position the attachment brackets (6)  
at the rear of the appliances at the top and  
bottom. Slide the upper attachment bracket  
upwards as far as possible. Secure it at the  
side using the screws provided (5). Do not  
overtighten!  
6.  
6
5
6.  
5
6
c.a210  
Figure 26  
A delight in freshness  
21  
WF1051 / EWTNes 2956  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
7. Figure 27: Push the long carriage bolt M5x260 (7)  
through the leveling wheels as shown. Fit in a  
washer (8). Screw on the wing nut (9) and tighten it  
manually. Do not overtighten.  
8. Turn the adjustable roller base up. Otherwise you  
will damage the floor when you push in the appli-  
ances.  
9. Secure the ventilation grille (10) to the appliance  
with screws (11).  
Push in the sealing strip (4) as shown.  
10  
9.  
4
11  
9
8
7
7.  
7
8.  
8 spanner  
2
4
3
10 spanner  
Figure 27  
A delight in freshness  
WF1051 / EWTNes 2956  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
10. Figure 28: Slide the side installation  
10.  
frames (15) upward until they are  
in contact with the underside of the  
ventilation grille, Figure 28.  
11. Secure the side frames with the  
adhesive section (17) to prevent  
them from sliding down. Remove the  
protective film and place the adhesive  
sections over the upper brackets.  
17  
11.  
12. Figure 29: Install anti-tip brackets for  
each appliance. Refer to “Blocking For  
Safety.”  
17  
15  
15  
11.  
17  
Figure 28  
3
1
2
min 3"  
Figure 29  
A delight in freshness  
WF1051 / EWTNes 2956  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
13. Figure 30, 31: Connect the appliances:  
- to the main power supply and  
- to the water supply if the appliance is  
equipped with an IceMaker. See “IceMaker,  
Water Connection,Figure 30.  
14. Carefully slide the connected appliances into  
the recess until the ventilation grille touches the  
top, Figure 31.  
13.  
15. Align the appliances by using only the outer  
leveling wheels at the front (3) and rear (2).  
Figure 30  
14.  
8 spanner  
2
3
10 spanner  
15.  
Figure 31  
A delight in freshness  
WF1051 / EWTNes 2956  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
16. Figure 32: Attach the aligned combination to the  
surrounding kitchen cabinet. Secure it through  
the side frames using the screws (20) provided.  
-
Cover the screws with cover caps (21).  
17. Now adjust the center adjustable roller bases (22)  
so that they make slight contact with the floor.  
18. Install the lower ventilation grille (23): Secure the  
ventilation grille so that it touches the floor and  
adjust it using the slots. Do not overtighten!  
20  
21  
16.  
8 spanner  
2
3
10 spanner  
17.  
22  
18.  
24  
24  
24  
23  
24  
Figure 32  
A delight in freshness  
WF1051 / EWTNes 2956  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
1. For built-in appliances without ventilation  
grilles and only with installation frame (2),  
ventilation must take place through the  
ventilation duct at the rear of the cabinet.  
Ensure that the ventilation cross-section is at  
least 31 square inches (200 cm²) per appliance.  
At least 62 square inches (400 cm²) for side-  
by-side installation of two appliances. Built-in  
appliances with an installation frame:  
- Figure 33: Screw the installation frame (2)  
to the appliance through the attachment  
brackets.  
At least 31 square inches (200cm2)  
per unit  
/4  
)
3
0
m
2
m
7
2
5
(
/4  
)
3
0
m
2
m
7
2
5
(
1.  
2
6
Figure 33  
A delight in freshness  
WF1051 / EWTNes 2956  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SIDE-BY-SIDE INSTALLATION  
Built-in appliances with a wooden ventilation  
grille:  
2. Figure 34: Cut out the wooden trim for use as a  
ventilation grille using the attached template.  
- The required ventilation cross-section must  
be at least 62 square inches (400 cm²) for  
side-by-side installation of two appliances,  
which corresponds to the attached template  
“double-size.”  
- Remove the attachment brackets from the  
installation frame (2) and screw them to the  
appliance from underneath.  
- Place the wooden ventilation grille (5) on the  
appliance, align it in the center and secure it  
from the rear using the attachment brackets.  
2.  
1/2"  
(13 mm)  
5
48"  
(1219,2 mm)  
3-11/16"  
(93,7 mm)  
X
Figure 34  
A delight in freshness  
WF1051 / EWTNes 2956  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Leviton Switch VZI06 1L User Manual
Life Fitness Elliptical Trainer X3 0 User Manual
Life Fitness Heart Rate Monitor Digital Heart Rate Sensors User Manual
Lightolier Work Light VRA2G9LS26USO User Manual
Linear DVD Player HTS ES1 User Manual
Lucent Technologies Stove MPB 33 User Manual
Makita Grinder 9627 User Manual
Marvel Industries Refrigerator 61ARMBBOL User Manual
MB QUART Car Speaker RSC 320 User Manual
McCulloch Chainsaw MAC 316 XT User Manual