Single Pole (One location) or 3-Way (Multi-location)
Electronic Switch
Cat. No. VZS15-1L, Lighted
Incandescent-1800W – Magnetic low-Voltage-1800VA (1440W)
Electronic Low-Voltage-1800W – Fluorescent-1800VA – Supplemental-1/2 HP
120VAC, 60Hz
DI-000-VZS15-02A-X3
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
WARNINGS AND CAUTIONS:
•
•
•
•
To be installed and/or used in accordance with appropriate electrical codes and regulations.
If you are unsure about any part of these instructions, consult a qualified electrician.
•
•
•
•
Use only one (1) ViziaTM electronic switch in a multi-location circuit with up to 9 coordinating remotes without LEDs or up to 4 matching remotes with LEDs
.
Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft (90 m).
Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.
Vizia™ electronic switches are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia™ on/off remotes.
Recommended minimum wall box depth is 2-1/2”.
IMPORTANT : For 3-Way applications, note that one of the screw terminals
Tools needed to install your Switch:
Step 4a cont'd
Step 4b cont'd
from the old switch being removed will usually be a different color (Black)
Switch
Switch
Coordinating Remote (no LED)
or labeled Common. Tag that wire with electrical tape and identify as the
common (Line or Load) in both the switch wall box and remote wall box.
Slotted/Phillips Screwdriver
Pencil
Electrical Tape
Cutters
Pliers
Ruler
Hot (Black)
Hot (Black)
WH
BK
WH
RD
WH
RD
BK
Changing the color of your Switch:
(unused)
Step 3
Preparing and connecting wires:
This switch can be wired using side wire terminal screws or
through backwire openings. Choose appropriate wire stripping
specifications accordingly.
BK
Your switch includes three color options. The switch ships with the White
frame attached. To change color of frame, proceed as follows:
Green
Ground
Green
Ground
Green
Ground
Black
YL/RD
RD
YL/RD
YL/RD
Black
Load
(unused)
Line
Line
120VAC, 60Hz
Load
120VAC, 60Hz
Use Terminal for 3-Way or
More Applications Only.
For Single-Pole Applications,
Do Not Remove This Label.
5/8"
White
Strip Gage
(1.6 cm)
White
(measure bare
wire here)
Cut
(if necessary)
Neutral (White)
Neutral (White)
Line up tabs and
press in side to attach
Push in side
at tab to release
WIRING SWITCH:
WIRING SWITCH:
Connect wires per WIRING DIAGRAM as follows:
NOTE: The switch must be installed in a wall box that has a Line Hot
connection.
Connect wires per WIRING DIAGRAM as follows:
INSTALLINGYOUR SWITCH
•
•
•
•
•
Green or bare copper wire in wall box to Green terminal screw.
Line Hot wall box wire to terminal screw marked "BK".
Load wall box wire to terminal screw marked "RD".
Line Neutral wall box wire to terminal screw marked "WH".
Switch terminal screw marked "YL/RD" should have Red insulation
label affixed.
NOTE: Use check boxes
when Steps are completed.
NOTE: Maximum wire length from switch to all installed remotes
cannot exceed 300 ft (90 m).
WARNING: TO AVOID FIRE SHOCK OR DEATH;TURN
OFF POWER at circuit breaker or fuse and test that power is
off before wiring!
Step 1
•
•
Green or bare copper wire in wall box to Green terminal screw.
Line Hot (common) wall box wire identified (tagged) when
removing old switch
Side Wire Connection
Side wire terminals accept #14
AWG solid wire copper only.
Back Wire (either hole may be used)
Back wire openings use #14-12 AWG
solid wire copper only.
NOTE: If insulating label is not affixed to terminal screw marked "YL/RD",
to terminal screw marked "BK".
���
���
���
���
��
��
��
��
��
��
���
���
���
���
���
���
��
��
��
�
use electrical tape to cover.
•
First Traveler wall box wire to terminal screw marked "RD"
(note wire color).
Remove Red insulating label from terminal screw marked "YL/RD".
Second Traveler wall box wire to terminal screw marked "YL/RD"
(note wire color). This traveler from the switch must go to the
terminal screw on the remote marked "YL/RD".
Line Neutral wall box wire to terminal screw marked "WH".
•
Proceed to Step 5.
•
Make sure that the ends of the wires from the wall box are
straight (cut if necessary).
•
•
���
3-Way Wiring with Coordinating Remote
•
•
•
•
Remove insulation from each wire in the wall box as shown.
For Single-Pole Application, go to Step 4a.
For 3-Way Coordinating Remote (no LEDs) Application, go to Step 4b.
For 3-Way Matching Remote (with LEDs) Application, go to Step 4c.
Step 4b
�
(no LED) Application:
•
Terminal
Screw marked
White (WH)
Identifying your wiring application (most common):
NOTE: If the wiring in your wall box does not resemble any of
these configurations, consult a qualified electrician.
Step 2
Coordinating Remote
Switch
WIRING COORDINATING REMOTE:
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BK" and "RD" terminals on coordinating remote are unused.
Tighten both screws.
Single Pole Wiring Application:
Step 4a
Terminal
Screw marked
White (WH)
1
H
W
BK
H
W
BK
Terminal
Screw marked
Black (BK)
NOTE: Maximum wire length from switch to last remote is
2
2
4
300 ft (90 m).
2
1
1
2
1
3
4
5
•
•
Green or bare copper wire in wall box to Green terminal screw.
Load wall box wire identified (tagged) when removing old switch to
First Traveler (note color as above).
Second Traveler wall box wire (note color as above) to terminal
screw marked "YL/RD". This traveler from the remote must go to
the terminal screw on the switch marked "YL/RD".
Remove White insulating label from terminal screw marked "WH".
Line Neutral wall box wire to terminal screw marked "WH".
Proceed to Step 5.
3
5
RD
Terminal
Screw marked
Yellow/Red
(YL/RD)
D
/R
L
Y
RD
D
/R
3
4
5
L
Y
1
2
H
W
3
4
BK
Terminal
Screw marked
Black (BK)
•
Terminal
Screw marked
Red (RD)
3
4
•
•
•
Terminal
Screw marked
Yellow/Red
(YL/RD)
RD
D
/R
L
Y
Single Pole
3-Way
1. Line (Hot)
2. Neutral
3. Ground
4. Load
1. Line or Load (see important instruction below)
2. Neutral
3. Ground
4. First Traveler – note color
5. Second Traveler – note color. NOTE: For
matching remote w/LEDs installation, the
First Traveler becomes Line Hot.
Terminal
Screw marked
Red (RD)
Terminal Label:
Use Terminal for 3-Way or More Applications Only.
For Single-Pole Applications, Do Not Remove This
Label.
Download from Www.Somanuals.com. All Manuals Search And Download.
|