|
LevelOne
WPS-0100
WPS-0100USB
Wireless Printer Server
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet Mail Printing.............................................................................................................. 49
Printing through the Internet.................................................................................................. 53
SNMP......................................................................................................................................... 54
Wireless Configuration........................................................................................................... 55
Chapter 8 Troubleshooting
60
Overview................................................................................................................................... 60
Hardware & LAN Problems .................................................................................................. 60
AppleTalk (Macintosh)........................................................................................................... 61
Novell NetWare ....................................................................................................................... 63
Windows Printing Problems .................................................................................................. 64
Appendix A Specifications
68
General Specifications............................................................................................................ 68
Protocol Support ...................................................................................................................... 70
Feature Support ........................................................................................................................ 70
Regulatory Approvals ............................................................................................................. 71
Appendix B Network Server Configuration
71
Windows NT Server................................................................................................................ 71
Windows 2000 Server............................................................................................................. 73
Novell NetWare ....................................................................................................................... 73
Unix Systems ............................................................................................................................ 78
Page ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
This chapter provides an overview of your LevelOne Printer Server's features.
Features
Congratulations on the purchase of your new LevelOne Printer Server. This device was
designed to provide a simple and efficient network printing solution. It is packed with features,
including:
Ø Versatility. The LevelOne Printer Server supports up to five protocols: NetWare, TCP/IP,
SMB (Service Message Block), AppleTalk (EtherTalk), and NetBEUI. It features one or
two Ethernet interface ports and operating system support includes Unix, Novell, and
Microsoft Windows.
Ø Easy Installation. The LevelOne Printer Server makes adding printers or plotters to
your network simple. Depending on your model, it will support 10BaseT only, 10Base2
and 10BaseT, or 10BaseT and 100BaseT. The auto-sensing feature on the LAN interface
means that there is no need to set jumpers or perform software configuration to select the
network interface used.
Ø Easy Setup. A number of utility programs are supplied to simplify setup. For Windows
95/98/NT/2000/XP users, the BiAdmin program makes it easy to configure the LevelOne
Printer Server for a variety of network and server configurations.
Ø Web-based Interface. On 100BaseT models, the Web-based interface provides an easy
method of configuration in TCP/IP networks.
Ø Compact Size. This allows the LevelOne Printer Server to be used even where space is
limited.
Ø Remote Management Tools. A variety of software tools are provided. In most
environments, both the LevelOne Printer Server and attached bi-directional printers can be
configured remotely.
Ø SNMP Support. The LevelOne Printer Server can act as a SNMP agent, with it own
MIB. This allows TCP/IP users to monitor, configure and troubleshoot the LevelOne
Printer Server using their existing SNMP management tools.
Ø JetAdmin Support. 100BaseT models support the HP JetAdmin program. If you are
already using JetAdmin, you can also use this program to manage your LevelOne Printer
Server.
Ø Internet Printing Protocol (IPP) Support. Some LevelOne Printer Server models can
act an IPP (Internet Printing Protocol) Server, allowing clients, suppliers, colleagues and
others to print to your printer from anywhere on the Internet. Windows IPP Client software
is also supplied.
See the "Protocol Support" and "Feature Support"
tables in Appendix A for details of which models
support the different features.
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
For your own safety, and to protect your LevelOne Printer Server, please observe the following
safety advice.
1. Unplug this device from its power source before cleaning. Use only a slightly dampened
cloth for cleaning. Do not use liquid or aerosol cleaners.
2. Avoid using this product near water. Exposure to water poses an electric-shock hazard.
3. Do not place the LevelOne Printer Server on an unstable surface. The device may fall
causing serious damage to the device.
4. This device should only be used with the power supply type specified on the marking label.
If you are not sure of type of your local power supply, consult your dealer or the local
power company.
5. Do not pinch, crimp or otherwise damage the power cord. If exposed to foot traffic,
ensures that the cable is properly shielded and does not pose a tripping hazard.
6. If using an extension cord, makes sure the total ampere rating of the products using the
cord does not exceed the extension cord's ampere rating.
7. Do not attempt to service this device, as opening or removing casing may expose you to
dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
8. The LevelOne Printer Server should be serviced by qualified service personnel under the
following conditions:
·
·
·
·
·
The power cord is damaged or frayed.
Liquid has been spilled onto the product.
The product has been exposed to rain or water.
The product does not operate normally in accordance with the operating instructions.
The device has been dropped or the casing has been damaged.
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
You should find the following items packaged with your LevelOne Printer Server. If any items
are missing, contact your dealer immediately.
·
·
·
·
·
The LevelOne Printer Server
Power Adapter
One CD-ROM containing all support programs and this manual
Quick Install Guide
Wireless PCMCIA Card (for WPS-0100 and WPS-0100USB)
Models
This manual covers the following LevelOne Printer Server models. Details of the LEDs and
DIP Switches are in this Chapter. Further details of each model are contained in Appendix A -
Specifications.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
WPS-0100
41 Parallel Printer Port
4IEEE 802.11b Wireless Station
410/100BaseT
WLAN
LED
PCMCIA
Wireless
Card
ACT
LED
LAN
LED
Error
LED
10/100
BaseT
Port
Parallel
Port
12V
Power
Diagnostic
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
WPS-0100USB
41 USB Printer Port
4IEEE 802.11b Wireless Station
410/100BaseT
WLAN
LED
PCMCIA
ACT
LED
Error
LED
Wireless
Card
LAN
LED
USB
Port
10/100
BaseT
Port
12V Power
Diagnostic
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators
All models have two LED indicators on the top. The Status/Error LED is orange or red. The
Power/Link indicator LED is green. The LED indicator modes are described in the following
table.
Green LED
Off
Red/Orange LED
Status Description
No power.
Off
On
On
Hardware error.
Flashing
On
Flashing
Firmware upgrade in progress.
No printer connected to the USB port.
Normal operation - idle.
Flashing (USB only)
On
Off
Off
Flashing
Normal operation - transmitting or
receiving packets from the network.
LEDs - WPS-0100 and WPS-0100USB
The WPS-0100 and WPS-0100USB have 2 additional LED indicators as follows:
LED
Description
WLAN ACT
Off - Idle
Flashing - Transmitting or receiving data through the Wireless
LAN.
LAN ACT
Off - Idle
Flashing - Transmitting or receiving data through the LAN.
Diagnostic Push Button
LevelOne Printer Server models WPS-0100 and WPS-0100USB are fitted with a Diagnostic
Push Button. The button is recessed; a pin or paper clip can be used to press it. This button has
2 functions:
·
·
Restore the factory default settings
Print a test page containing all current settings.
To restore the factory default settings:
1. Turn the LevelOne Printer Server OFF.
2. Press and hold the diagnostic button. While pressing the button, switch the LevelOne
Printer Server ON.
3. If you continue pressing the button for 10 seconds, a diagnostic page will be printed,
showing the new (default) settings.
To generate a Diagnostic print out
1. Ensure that both the LevelOne Printer Server and the printer attached to port 1 are ON.
2. Press the diagnostic button, and hold it in for 2 seconds.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The test page, containing the current settings, will be printed.
Note:
PostScript printers are unable to print this page. If you have a PostScript printer on Port 1,
the test page will not be printed.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
LAN Installation
This chapter describes how to install the LevelOne Printer Server in your Local Area
Network.
Procedure
1. Preparation
·
·
Ensure the power is OFF. Do not connect the LevelOne Printer Server while power is On.
For the PS 7100 and WPS-0100USB only, the PCMCIA wireless card must be inserted
into the PCMCIA slot on the rear.
With the LEDs on the PCMCIA card facing UP, slide the card into the PCMCIA slot until
it encounters some resistance. Push firmly and it will click into position.
·
Find the Default Server Name for your LevelOne Printer Server.
The Default Server Name is shown on a sticker on the base of the device. It consists of 8
letters and/or digits. Record this name; it may be needed during configuration.
2. Connect the Printer or Printers
Connect the printer or plotter to the LevelOne Printer Server's printer port(s), as appropriate:
·
·
·
USB Ports - Use the USB cable supplied with your printer to connect the printer to the
LevelOne Printer Server's USB port
Parallel Ports - Use standard Parallel port cables to connect the printer to the parallel port
on the LevelOne Printer Server. Parallel printer cables should be less than 3 meters long.
Serial Port - Use a standard Serial port cable to connect the printer to the serial port on the
LevelOne Printer Server.
3. Connect the Network Cable
·
Connect the network cable to the proper connector on the LevelOne Printer Server. The
LevelOne Printer Server will automatically recognize whichever connector is used.
·
Note that if your LevelOne Printer Server has both BNC and UTP (10BaseT or
10/100BaseT) connectors, only ONE (1) connection can be used.
On the WPS-0100 and WPS-0100USB, connecting the LAN cable will
disable the Wireless interface, because the default "Infrastructure
mode" wireless setting can NOT be used with the LAN interface.
To use both the LAN and Wireless interfaces, the Wireless mode
must be set to "Ad-hoc".
After configuration, the LAN interface can be disconnected if not
required.
4. Power Up
Plug in the power adapter cable and power up. Start-up will take only a few seconds.
Use only the Power Supply unit provided with the device. Power
Supply units for different models are not interchangeable.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
LAN Installation
5. Check the LEDs
·
·
The Red Error LED should flash, then turn Off. When the Red LED goes off and the
Green LED remains lit or flashes, the LevelOne Printer Server is ready.
For models with USB ports, the Red Error LED will remain flashing if the LevelOne
Printer Server can't connect to the printer.
·
If your model supports 10BaseT and 100BaseT, check the 10/100BaseT link LED or
LEDs next to the LAN connection. If the auto negotiation Fails, the LED (or both LEDs, if
there are 2) will be Off. In this case, set the DIP switches to suit your LAN, as described in
the DIP Switch Table in Chapter 1.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
LevelOne Printer Server
Configuration
This chapter provides an overview of the configuration process.
Overview
The LevelOne Printer Server is designed to support many different platforms, and the
configuration required would depend upon the environment in which it is installed.
·
·
·
The LevelOne Printer Server usually requires configuration. A Windows-based setup
Wizard is provided on the CD-ROM to simplify this task.
PCs wishing to use the printer attached to the LevelOne Printer Server always require
configuration. See Chapter 4- Client Configuration for details.
If using a NetWare Server (V3, 4, or 5 in "compatibility" mode), the supplied Setup
Wizard can also configure the NetWare Server for basic operation.
·
For advanced configuration and management, the BiAdmin program (detailed in
Chapter 6 - BiAdmin Management Utility) is recommended.
·
If using NDPS, refer to Appendix B - Network Server Configuration.
·
If you wish to use a queue-based printing system using Windows NT Server/Windows
2000, the Network Server must be configured as detailed in Appendix B - Network Server
Configuration. However, it is not necessary to use a Network Server-based queue; client
PCs can print directly to the LevelOne Printer Server using the Peer-to-peer Print Driver
installed by the User setup option on the CD-ROM.
Using the Windows Wizard
The Windows-based Wizard runs on Windows 95, 98, NT4.0, Windows 2000 and XP.
It will configure the LevelOne Printer Server for your Network environment.
If using NetWare, the Wizard can also configure the NetWare Server, provided:
·
·
You are logged into the required NetWare server with ADMIN rights.
NetWare Client32 is installed on the PC you are using for configuration.
Procedure
1. Insert the supplied CD-ROM into your drive. If the setup program does not start
automatically, run SETUP in the root folder.
2. Select the Administrator installation option. This will install both the Wizard and the
BiAdmin management program. (See Chapter 5 for details on using BiAdmin.)
3. Follow the prompts to complete the installation.
4. Run the Setup Wizard, either by using this option on the final installation screen, or by
selecting it from the menu created by the installation.
5. Within the Setup Wizard, select the LevelOne Printer Server you wish to configure, click
Configure, and step through the Wizard.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
If the desired LevelOne Printer Server is not listed:
·
·
Check all cables to the LevelOne Printer Server.
Check the LevelOne Printer Server's LEDs:
·
·
The Red LED should be OFF and the Green LED should be ON or flashing.
If your model supports 10BaseT and 100BaseT, check the 10/100BaseT link LED
next to the LAN connection. If the auto negotiation fails, the 10/100BaseT Link LED
will not light when the device is powered up. (If there are 2 LEDs, neither will light.)
·
Check that your PC has either the TCP/IP or NetBEUI network protocols installed.
See Checking your Network Protocols for details.
·
If you PC can't configure the LevelOne Printer Server correctly (in Infrastructure mode),
then try to connect to LAN and disable the Wireless.
Wireless Configuration
For the WPS-0100 and WPS-0100USB, which include Wireless Stations, the Wizard will
display a "Wireless" configuration screen.
For further details about the WPS-0100 and WPS-0100USBs' Wireless Station feature, refer to
Wireless Configuration in Chapter 7 - Special Features.
The WPS-0100 and WPS-0100USB do NOT allow both a LAN
connection and "Infrastructure" mode.
To use "Infrastructure" mode, you must DISCONNECT the LAN
cable after configuration.
If using "Ad-hoc" mode, the LAN cable can be left connected,
and both the LAN and Wireless interfaces are available.
Alternatives to the Windows Wizard
If you do not have a Windows 32 platform available, use one of the following methods to
configure the LevelOne Printer Server.
Web Browser
FTP
Only available on 100BaseT models. See Chapter 6 - Web Interface
Setup for details.
Using this method, the configuration file is downloaded from the
LevelOne Printer Server, edited, then sent back. No software needs to be
installed.
See the UNIX manual for details. The Unix manual is on the CD-ROM,
in the Manual\Unixfolder
WPConfig
PSConfig
This program requires Windows 3.1, and the IPX/SPX protocol.
This program is on the CD-ROM, in the Utilities\WPConfig
folder. Instructions for using the program are in a sub-folder of the
Manualfolder on the CD-ROM.
Menu-based DOS program, intended only to configure the LevelOne
Printer Server for use with NetWare V2, 3 and 4.
This program is on the CD-ROM, in the Utilities\DOSfolder.
Instructions for using the program are in a sub-folder of the Manual
folder on the CD-ROM.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Quickset
Command-line DOS program, intended only to configure the LevelOne
Printer Server for use with NetWare V2, 3 and 4. This program also has
a limited ability to configure the NetWare Server itself.
This program is on the CD-ROM, in the Utilities\DOSfolder.
Instructions for using the program are in a sub-folder of the Manual
folder on the CD-ROM.
Advanced Configuration and Management
The BiAdmin management utility is provided for advanced configuration and management.
This program is installed by default when the Administrator install option is chosen.
·
·
See Chapter 5 for details on using BiAdmin.
For instructions on using BiAdmin for NetWare configuration, see the NetWare manual on
the CD-ROM. It is located in the Manual/Netwarefolder.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Client PC Configuration
The chapter details the client configuration required on LAN clients to use the printer
or printers attached to the LevelOne Printer Server.
Overview
Before performing client configuration, the following conditions must be met:
·
·
·
·
LevelOne Printer Server must be installed on your LAN
LevelOne Printer Server must be configured (refer to Chapter 3).
Both the LevelOne Printer Server and the attached printer must be powered ON.
If the client PC uses a Wireless connection to communicate with the LevelOne Printer
Server, the PC's wireless settings must be correct, as described below.
Wireless Settings for client PCs
The WPS-0100 and WPS-0100USB incorporate Wireless Stations for IEEE 802.11b devices.
This section is only relevant to users of the WPS-0100 and WPS-0100USB.
To print to the WPS-0100 and WPS-0100USB, Wireless stations must ensure that the
following Wireless Settings are correct.
Ad-hoc Mode
Infrastructure Mode
SSID
Must match the other Wireless stations, Must match the Access Point.
(WPS-0100 or WPS-0100USB) unless
the SSID is null or "any".
If its SSID is null or "any", a Wireless
station can join any Ad-hoc group.
Channel
Should match the other Wireless
stations (WPS-0100 or WPS-
0100USB).
Access Point sets the Channel
used.
Wireless stations
However, when joining an existing ad-
automatically locate the
hoc group, a Wireless station must use correct channel.
the Channel in use, rather than its own
Channel.
WEP Settings
Must match the other Wireless stations. Must match the Access Point.
(WPS-0100 or WPS-0100USB)
To change these settings on your PC, use the software provided with your Wireless card.
If your PC's wireless settings are not correct, you will not be able to print to the WPS-0100 or
WPS-0100USB via a Wireless connection.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Methods
The LevelOne Printer Server supports a number of printing methods:
·
Peer-to-peer Print Driver is used by the User installation on the CD-ROM. The print jobs
are stored (queued) on your PC, and sent to the LevelOne Printer Server when it is
available.
·
Server-based Print Queue means that the all print jobs are stored (queued) on the Network
Server (e.g. NetWare, Windows NT/2000) and then sent to the LevelOne Printer Server.
This allows the Network Administrator to modify the Print Queue. For example, an
important job can be moved to the head of the queue.
·
·
Windows SMB printing is a Microsoft standard for using a "Network Printer". No
additional software needs to be installed on your Windows PC, and printing from MS-
DOS programs is supported. However, because the LevelOne Printer Server can not store
files, large print jobs may cause problems.
AppleTalk is also supported, and normally no configuration of the LevelOne Printer
Server is required. See the Macintosh section of this chapter for details of client
configuration.
Which printing method should I use?
·
·
If using Windows 95, 98, NT, XP, or 2000, the easiest method is to install the Peer-to-peer
Print Driver on the CD-ROM, by selecting the User installation.
If using Windows, and you need to print from MS-DOS programs, or you don't wish to
install additional software, use SMB.
However, SMB is not suitable for large, complex documents, so if you need this as well as
MS-DOS printing, you should install BOTH the Peer-to-peer Print Driver and SMB
printing. MS-DOS programs can use the SMB printer, Windows programs should use the
Peer-to-peer Print Driver.
·
If your LAN has Network Servers (e.g. Windows NT, Windows 2000 Server, NetWare)
use the method advised by your Network Administrator. The LevelOne Printer Server can
print via a queue located on a Network server, if desired.
·
·
Unix users - refer to the Unix Manual on the CD-ROM, in the Manual/Unix directory.
Macintosh users - refer to the Macintosh section of this chapter.
Checking your Network Protocols (Windows)
Your PC must have EITHER the TCP/IP or NetBEUI protocols installed.
·
·
If using the Peer-to-peer Print Driver, the installation program will check this for you.
If using Windows SMB Printing, you must check manually, as described below.
(This is for Windows 95 only. All later versions of Windows have TCP/IP installed by
default.)
1. Select the Settings - Control Panel - Network option on the Start Menu. You should see a
screen like the one following:
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1: Network Configuration
·
·
The top line in the list (NetBEUI -> PCI Fast Ethernet Adapter) indicates that the
NetBEUI protocol is installed on this PC. Your PC will show the name of the your
Network card rather than "PCI Fast Ethernet Adapter".
The highlighted line (TCP/IP -> PCI Fast Ethernet Adapter) indicates that TCP/IP is
installed. Your PC will show the name of the your Network card rather than "PCI Fast
Ethernet Adapter".
2. If neither line is present:
·
Install the NetBEUI protocol by selecting Add - Protocol - Microsoft - NetBEUI - OK.
You may be prompted for your Windows CD-ROM.
·
If required, you can also install TCP/IP. However, depending on your LAN
environment, TCP/IP may require further configuration.
3. If either protocol is already installed, proceed with installation.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows Peer-to-peer Print Driver
With this printing method, print jobs are stored (queued) on your PC, and then sent to the
LevelOne Printer Server when it is available.
Setup
Before performing the following procedure, the LevelOne Printer Server must be installed on
your LAN, and configured as described in Chapter 3. Both the LevelOne Printer Server and the
attached printer should be powered ON.
1. Insert the supplied CD-ROM into your drive. If the setup program does not start
automatically, run SETUP in the root folder.
2. Select the Installation icon, then choose the User option in the "Setup Type" screen. This
will install the Peer-to-peer Print Driver.
3. Follow the prompts to complete the installation. (Refer to the Windows section of Chapter
8 - Troubleshooting if there is a problem with the installation.)
4. The Print Driver Setup will then run.
5. The LAN will be searched for LevelOne Printer Servers, and a screen like the following
will be displayed.
·
·
If desired, change the Workgroup name and click Refresh.
Select List all LevelOne Printer Servers to list all LevelOne Printer Servers,
regardless of Workgroup.
·
The name of the attached printer will be displayed if possible. If "No printer" is
displayed, check that the printer is properly connected and powered on.
Figure 2: Printer Port Setup (Peer-to-peer Print Driver)
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
If your LevelOne Printer Server is not listed:
·
·
Select "List all LevelOne Printer Servers", and click the "Refresh" button.
Check that both the LevelOne Printer Server and the printer are properly
connected, and powered on.
·
·
Check that the LevelOne Printer Server has been configured. (Use the Setup
Wizard on the CD-ROM.)
If using TCP/IP, try installing the NetBEUI protocol. See the earlier section
Checking your Network Protocols for details. Then uninstall and re-install
the Peer-to-peer Print Driver.
6. Select the desired printer port, and then click the "Next" button. A pop-up message will
inform you if the port has been created successfully.
If you see the following error message, either install Internet
Explorer 4 or later, or follow the procedure in the "Trouble
Shooting - Windows" section of Chapter 8.
7. Then a screen like the following will be displayed:
Figure 3: Configure Printer Port
8. Select the correct Windows printer in the Existing Printers list, and click the "Connect"
button.
If the correct printer type is not listed, click "Add New Printer" to run the Windows Add
Printer wizard. Step through the Wizard and install the required printer:
·
Select the correct Printer Manufacturer and Model, or use the "Have Disk" option if
appropriate.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
·
We recommend changing the Printer name to indicate which device is on.
(e.g. HP2100 on SCA43600_P1)
·
·
If prompted about Sharing the printer, do NOT enable Sharing
When the Printer installation is finished, it will be listed in the Configure Printer Port
screen above. Select it and click "Connect".
9. You can now print using this printer.
·
·
To install additional Printers, repeat steps 6 to 8.
Use the Start menu to run this program in future. The default installation is Start -
Programs - Printer Server Utility - Printer Server Setup.
Management
·
·
·
Print jobs can be managed like any Windows printer. Open the Printers folder (Start -
Settings - Printers) and double-click any printer to see the current print jobs.
If the printer attached to the LevelOne Printer Server is changed, just run this program
again, and select the correct printer.
To delete a port created by this setup program, use the Windows Delete Port facility:
·
·
Right-click any printer in the Printers folder, and select Properties.
Locate the Delete Port button. This button is on the Details or Ports tab, depending on
your version or Windows.
·
If the LevelOne Printer Server's IP Address is changed, and you can no longer print, delete
the port (see procedure above) and re-install it.
Port Options
The options for the Peer-to-peer Print Driver are accessed via the Port Settings button.
Use Start - Settings - Printers to open the Printers folder, then right-click the Printer, and select
Properties. The Port Settings button is on the Details or Ports tab, depending on your version
of Windows.
An example screen is shown below:
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4: Port Settings (Peer-to-peer Driver)
Items shown on this screen are as follows:
Port
If desired, click Browse to select a different LevelOne Printer Server. If
the selected device has multiple ports, the Select Device Port button can
be used to select the port.
The Port Name can not be changed after installation. This name is
shown in the Printer's Properties.
Banner
Check this option to print a banner page before each print job.
·
·
If using a PostScript Printer, check the PostScript box.
The User Name will be printed on the banner page.
Retry Interval
Sets how often Windows will poll the LevelOne Printer Server to
establish a connection when the printer is busy. Increase this value if
you get too many warning messages.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows SMB Printing
This method requires no additional software to be installed, but the NetBEUI or TCP/IP
protocol must be installed on your PC. Use the following procedure to install the LevelOne
Printer Server's printer as a Windows SMB network printer:
1. Double-click the Network Neighborhood icon on the desktop.
2. On the View menu, select Details.
3. Locate the desired LevelOne Printer Server, as shown below:
·
·
If it is the same Workgroup as your PC, it will be listed on screen.
If it is in a different workgroup, double-click Entire Network, then double-click the
appropriate Workgroup to open it.
Figure 5: Network Neighborhood
4. Double-click the LevelOne Printer Server icon to view a Printer icon for each printer port.
The "Comment" field may indicate what type of printer is connected to the port.
5. To install a printer, right-click the desired printer icon, and choose "Install", as shown
below. This will start the Add Printer wizard.
Figure 6: Install SMB Printer
6. Follow the prompts to complete the installation.
·
For information about the question "Do you print from MS-DOS programs?", see
Printing from MS-DOS Programs below.
·
Select the Printer Manufacturer and Model to match the printer connected to this port
on the LevelOne Printer Server, and complete the Wizard.
7. This printer will now appear in your Printers folder (Start - Settings - Printers) and can be
used like any other printer. However, SMB printing is not suitable for large complex print
jobs - you should use the Peer-to-peer Print Driver instead.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing from MS-DOS Programs
Windows can redirect print data from a parallel port on your PC (e.g. LPT1) to a network
printer. This redirection is called "Capture Printer Port", and is useful for MS-DOS programs.
The MS-DOS program is configured to use LPT1 (parallel port 1 on the PC), but Windows
"captures" the print data and sends it to the network printer.
Capture settings can be set by:
·
Saying "Yes" to the prompt "Do you print from MS-DOS programs?" when installing a
Network Printer.
·
OR, using the Capture Printer Port menu option shown in Figure 6 above.
This will result in a dialog like the following, where you can select the port on the PC to be
captured. Normally, this will be LPT1 (parallel port 1 on the PC).
Figure 7: Capture Printer Port
The File menu in the Printers folder also has options for Capture Printer Port and End
Capture.
Windows with Server-based Print Queues
1. Open your Printers folder, and start the Add Printer Wizard.
2. When prompted, select Network Printer.
3. When prompted for Network Path or Queue Name, click the Browse button, and locate the
Server and Printer (or Print Queue) which your Network Administrator advised you to use.
4. Click OK, then Next.
5. Select the correct printer Manufacturer and Model, as advised by your Network
Administrator, and click Next.
6. Follow the prompts to complete the Wizard.
The new printer will be listed with any other installed printers, any may be selected when
printing from any Windows application.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows using NDPS
Before using NetWare NDPS (NetWare Distributed Printing Service), one or more NDPS
Printer Agents must be created on the NetWare Server. See Appendix B for details of this
procedure.
Also, on your workstation, ensure that:
·
·
Novell IntranetWare Client v2.2 (or later) is installed on your PC.
You have access to the Novell Printer Manager utility (e.g. Nwpmw32.exe).
Procedure
1. Start the Novell Printer Manager utility.
2. Select Printer - New from the menu, then click Add.
3. Select the required printer and click Install, then Close.
Figure 8: NDPS Manager - Client
4. The printer (e.g. SerPrinter in the example above) appears in the main Printer Manager
window in the Name list, and is available for print jobs. Printer drivers are automatically
downloaded from the server as required.
5. The printer will appear in your Windows printer list, and may be used from by any
Windows application.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Macintosh (AppleTalk)
The LevelOne Printer Server supports AppleTalk (EtherTalk), PAP, ATP, NBP, ZIP and DDP
protocols, enabling Macintosh computers on the network to view and use the LevelOne Printer
Server as a regular AppleTalk printer.
Normally, no configuration is required. For advanced users, the PSTool program has been
provided specifically for the Macintosh environment.
Software Requirements
System 7.x OS or newer.
AppleTalk Setup
1. Click the apple icon and choose Control Panel.
2. Click Network.
3. Ensure that EtherTalk is selected under AppleTalk Connection.
4. Click Chooser. The Chooser panel will open.
5. Click on either the LaserWriter 8 icon (recommended) or the LaserWriter 7 icon.
LaserWriter 8 makes use of the fonts installed in the printer itself, so the printing response
time is quicker. LaserWriter 7 uses the fonts installed in the computer, which increases
network traffic and takes more printing time.
6. Select a LevelOne Printer Server from the printer list by clicking on the appropriate name.
The LevelOne Printer Server's name is recorded on a label on the bottom of the LevelOne
Printer Server as "Server Name". This name consists of 8 digits and/or numbers.
7. Click on the Close box.
Configuration is now complete.
Printing
Printing with the LevelOne Printer Server installed in an AppleTalk network is identical to
normal printing. Just select File - Print and choose the desired printer.
Advanced Setup and Management
In a mixed Windows PC/Macintosh environment, you can use BiAdmin to configure the
LevelOne Printer Server. See Chapter 5 for details on installing and using BiAdmin.
On the Mac, you can use SimpleText to edit the LevelOne Printer Server's CONFIG file and
the supplied PSTool program to send it to the LevelOne Printer Server. The procedure is as
follows:
1. Copy the following files from the Utility\Apple folder on the CD-ROM to an appropriate
folder on your hard disk.
PSTool
CONFIG.xxx
Select the appropriate CONFIG file for your model as follows:
config.1p
confiig2p
config.2p1s
config.3p
Single parallel port models
Dual parallel port models
Two parallel ports, 1 serial port model
Models with 3 parallel ports
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Use Chooser to select the desired LevelOne Printer Server.
3. Double click the CONFIG file, and edit it. The appropriate values for each line are
described in the following section. The file should look like the example below, but may
vary depending on your model.
Begin CMD
0001 Device Name: xxxxxxxx
3000 Apple Zone : *
3001 Printer Type (P1): LaserWriter
3002 Printer Type (P2) LaserWriter
3003 Printer Type (SP): LaserWriter
3004 Printer Type (P3) LaserWriter
3101 AP_PCOMM1: No
3102 AP_PCOMM2: No
3103 AP_PCOMM3: No
3104 AP_PCOMM4: No
Serial Port Configuration
0030 Baud Rate: 9600
0031 Stop Bits: 1
0032 Parity: None
0033 Data Bits: 8
0034 Handshake: HARDWARE
9002
Do NOT modify the following lines:
beginCMD
9002:
4. Save the file.
5. Double click the icon for PSTool.
6. Click the Printer submenu and choose Download Postscript File. A panel will appear with
a list of files.
7. Click the CONFIG file. Then click Download.
AppleTalk Settings
When editing the CONFIG file, only the parameter should be changed. The parameter is the
last part of the line, after the colon (:). Ensure that you use only valid parameters.
0001 Device Name
The Device Name will initially be the Default Server Name. The
Default Server Name is shown on a sticker on the base of the device.
The Device Name can be changed, but the new name MUST NOT
exceed 19 characters in length.
3000 Apple Zone
Printer Type
The default value "*" allows all AppleTalk zones to access the
LevelOne Printer Server's printers. To restrict access to a particular
zone, enter the zone name here
These are text fields, used to describe the printer driver used for each
port. P1, P2, P3 refer to the parallel ports, while SP refers to the
Serial Port The name can be up to 19 characters long.
AP_PCOMMn
These settings determine whether the port uses ASCII or Binary
Communication Protocol. Enter NO for ASCII or YES for Binary.
Values for n
·
Binary communication is twice as fast as ASCII.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
·
·
ASCII communication is more reliable.
1 = parallel port 1
2 = parallel port 2
3 = serial port
The computer, LevelOne Printer Server and printer MUST all be
configured to use the SAME protocol. Check your printer
manual for details of printer configuration, and use the Print
menu to configure your computer, so that they use the same
settings as the LevelOne Printer Server.
4 = parallel port 3
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
BiAdmin Management Utility
This chapter describes the installation and operation ofthe BiAdmin Configuration &
Management program.
Requirements
This program requires:
·
·
Windows 95, Windows 98 or ME
Windows NT 3.51, Windows NT 4.0, Windows 2000 or XP
Additional Recommendations:
·
·
Screen resolution of 800 * 600 or greater.
If using Novell NetWare, installation of Novell's Client 32 for Windows is strongly
recommended. This will greatly enhance the ability to BiAdmin to work with NetWare
servers.
Installation
Use the supplied CD-ROM. This CD-ROM will usually auto-run. If auto-run is disabled on
your PC, run the SETUP program in the root folder.
·
·
BiAdmin is always installed if the Administrator option is chosen.
If using the Custom option on the CD-ROM, select BiAdmin Management Utility.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
·
·
Start the program by using the icon created by the setup program.
When run, the program searches the network for all active LevelOne Printer Servers, then
lists them on screen, as shown by the example screen below.
Main Screen
Figure 9: BiAdmin Main Screen
Groups
On the left side of the screen is a column for Groups. Each LevelOne Printer Server may be
placed in a group, using the Configuration-System Configuration-Groups menu option.
·
If a group is selected, only LevelOne Printer Servers in that group will be listed on the
right side of the screen.
·
·
By default, all LevelOne Printer Servers will appear in the [ROOT] group.
A LevelOne Printer Server can only be a member of one (1) group, and will always be a
member of a group.
·
·
Use the Configuration-System Configuration-Groups menu option to select a group for the
current LevelOne Printer Server.
To create a new Group and add the current LevelOne Printer Server to it, just enter a group
name in the dialog. (See example screen below)
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 10: System Configuration - Groups
Device List
On the right side of the screen is a list of all LevelOne Printer Servers found on the network.
For each device, the following data is shown:
·
·
Default Name. The Default Server Name is shown on a sticker on the base of the device.
Device Name. If you have not changed the name, this will be the same as the Default
Server Name.
·
Printer Port. The number and type of ports is shown in the right column.
If the desired LevelOne Printer Server is not listed, try the following:
·
·
Check that the device is installed and ON, then Refresh the list.
Use the InitDevice - Find menu option to search for the LevelOne Printer Server. You
need to know the Default Name of the LevelOne Printer Server. The Default Server Name
is shown on a sticker on the base of the device.
·
·
If the LevelOne Printer Server is on another LAN segment, use the InitDevice - Attach
Remote menu option to locate and display the LevelOne Printer Server.
For networks using ONLY TCP/IP, LevelOne Printer Servers without an IP Address will
not appear. Use the InitDevice - Set IP Address menu option to assign an IP Address, then
Refresh the list. You need to know the Default Name of the unlisted device in order to
assign an IP Address. The Default Server Name is shown on a sticker on the base of the
device.
Status Icons
Once a LevelOne Printer Server has been selected, the Icons become active.
The icons provide status information as well as access to the
selected LevelOne Printer Server settings. If an icon is grayed out,
that option or protocol is unavailable.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
Device Information
Menu equivalent: Status - Backup/Restore Device Information
All of the settings for the current device are displayed in a read-only scrollable list
in the left panel.
You can use the "Save to File" and "Restore to Device" buttons on this screen to
save a copy of the selected device's CONFIG file to your PC, or restore a
previously saved file to the selected LevelOne Printer Server.
Port Status
Menu equivalent: Status - Port Status
After selecting this icon, a Detail button will be available to show more
information about the printer.
Configuration Icons
The following icons are available. Refer to the on-line help for details of the data on each
screen.
NetWare
Menu equivalent: Configuration - NetWare
BiAdmin supports configuration of both the LevelOne Printer Server and Novell
NetWare servers.
·
·
You need to be logged into the NetWare server(s) with ADMIN rights.
The screens you will see, and the operations which can be performed, depend
on whether or not you have Novell NetWare Client 32 installed.
·
If Novell NetWare Client 32 is installed on your PC, BiAdmin allows
you to configure both the LevelOne Printer Server and the NetWare
server from within BiAdmin.
·
If this Novell NetWare Client 32 is NOT installed, you can configure
only the LevelOne Printer Server itself, not the NetWare server.
·
The NetWare Manual (in the Manual\NetWare folder on the CD-ROM)
contains detailed information on using BiAdmin with NetWare Servers.
TCP/IP Configuration
Menu equivalent: Configuration - TCP/IP
Selecting this icon will allow configuration for TCP/IP. Some models may have
checkboxes for DHCP, Bootp, and Rarp. Some models may also display the setup
data for the proprietary "Internet Printing" feature (printing via E-Mail).
AppleTalk Configuration
Menu equivalent: Configuration - AppleTalk
Generally, no LevelOne Printer Server configuration is required in order to use
AppleTalk.
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
NetBEUI Configuration
Menu equivalent: Configuration - NetBEUI
SNMP Configuration
Menu equivalent: Configuration - SNMP
Configuration is only required if using Simple Network Management Protocol.
See Chapter 7 for details.
Wireless Configuration
This Icon will be active if the selected device has the capability to serve as a
Wireless Station for your LAN. See Wireless Configuration in Chapter 7 -
Special Features for details.
Logical Port Configuration
Menu equivalent: Configuration - Logical Port
Logical port (printers) can be used in the NetWare and Unix environments.
Other Icons
Upgrade
Menu Equivalent: InitDevice - Upgrade
This option allows you to upgrade the firmware for the selected LevelOne Printer
Server. Before using this option, you need to obtain the .BIN file for the firmware
upgrade, and copy it to the same directory as BiAdmin.
Refresh
Menu Equivalent: None
Select this icon to update the LevelOne Printer Server device lis ting after
changing the name or IP Address.
Exit
Menu Equivalent: Help - Exit
Exit the BiAdmin program. This does not save any changes you have made; you
must Save to Device on each screen.
Menu Options
Status Menu
Device Info
Same as Device button.
Display all the configuration and status information about the selected
LevelOne Printer Server. The data is presented in a scrolling, read-
only window.
Port
Same as Port Status buttons.
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
InitDevice Menu
Attach Remote
This is used to connect to a LevelOne Printer Server device on another
LAN segment. If your LAN does not have a Router, ignore this option.
Connected
Protocol
This option allows you to designate which LAN protocol will be used
for communication between the selected device and this application.
You should select ONE protocol only.
Find
Use this option to use the IPX/SPX protocol to locate a LevelOne
Printer Server on the LAN. Simply enter the Default Name of the
LevelOne Printer Server you wish to locate. The Default Server Name
is shown on a sticker on the base of the device.
Reset Device
This will cause the device to reboot. This should be done after making
any configuration changes, or if the device stops responding after some
problems.
Restore Factory
Default
This will restore ALL device values to their factory defaults. To restore
only the current screen, use the Set to Default button on the screen.
Set IP Address
For TCP/IP networks only:
·
·
If a LevelOne Printer Server does not appear on the main screen,
use this option to set a Device IP Address, Gateway IP Address,
and Network Mask to the LevelOne Printer Server.
This should only be necessary if your LAN is using ONLY the
TCP/IP protocol. In other cases, BiAdmin will use IPX/SPX to
locate the LevelOne Printer Server even if it doesn't have a valid
IP Address.
·
To locate the LevelOne Printer Server, enter the Default Name.
The Default Server Name is shown on a sticker on the base of the
device.
·
·
Enter the required IP Address, Network Mask, and Gateway IP
Address.
After saving the data to the device, refresh the listing. The
LevelOne Printer Server should then appear in the device list on
the main screen.
Upgrade
Upgrade the firmware in a LevelOne Printer Server. See Upgrade Icon
for details.
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Menu
The System option allows you to:
·
·
·
Change the name of the selected LevelOne Printer Server.
Change the "Group" for the selected LevelOne Printer Server.
Set the Network Protocols used the selected LevelOne Printer Server. (Any protocols not
used on your LAN may be disabled. This may improve performance.)
The Configuration Menu also contains selections for each of the following. These have the
same effect as the corresponding Icon:
·
·
·
·
·
·
·
NetWare
TCP/IP
AppleTalk
NetBEUI
Logical Port
SNMP
Wireless
Diagnostics menu
Print Test Page
Use this option to print a test sheet from the selected LevelOne
Printer Server port. The test print out will include status
information.
Control Menu
Abort Mail Print Job
This menu option refers to print jobs which has been received
through the proprietary "Internet Printing" feature (printing via E-
Mail). This menu option can be used to terminate a print job which
is not printing correctly.
Some models support the IPP (Internet Printing Protocol) standard.
The "Abort Mail Print Job" menu option does NOT cancel IPP print
jobs.
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Web Interface Setup
This chapter explains how to use your Web Browser to configure the 100BaseT
LevelOne Printer Server models
Overview
100BaseT LevelOne Printer Server models incorporate the HTTP server. This allows you to
connect to the LevelOne Printer Server and configure it using your Web Browser. Most
browsers should work, provided they support tables and forms.
Preparation
Because it supports dynamic IP Address allocation using DHCP, BOOTP, or RARP, the
LevelOne Printer Server ships with an IP Address of 0.0.0.0. This is NOT a valid IP Address.
Therefore, you must do ONE of the following:
·
·
·
·
Check your DHCP server (if you have one), and determine the IP Address allocated to the
LevelOne Printer Server.
Use the Diagnostic Button (if fitted) to print a to print a report which includes the current
IP address. (Press the Diagnostic Button, and hold it for 2 seconds.)
Use the Setup Wizard, BiAdmin or another LevelOne Printer Server utility to allocate a
valid IP Address to the LevelOne Printer Server.
Add an entry to the arptable to associate the hardware address of the LevelOne Printer
Server with the desired IP address, as follows:
arp -s IP_Address 00:c0:02:xx:xx:xx
arp -s IP_Address 00-c0-02-xx-xx-xx
(Unix)
(Windows)
Where:
IP_Addressis the IP Address you wish to assign to the LevelOne Printer Server.
00:c0:02:xx:xx:xxis the hardware address of the LevelOne Printer Server.
Example (Unix):
arp -s 192.168.0.21 00:c0:02:12:34:56
Example (Windows):
arp -s 192.168.0.21 00-c0-02-12-34-56
Note: The hardware address of the LevelOne Printer Server is shown on a sticker on the base
of the device.
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the LevelOne Printer Server
1. Start your Web Browser.
2. In the Address box, enter HTTP:// followed by the IP Address of the LevelOne Printer
Server.
e.g.
3. You will then be prompted for the password. If no password has been set, just press ENTER.
4. Use the menu bar on the top of the screen to move about. Remember to save each screen
before changing to a different screen.
Configuration Screens
AppleTalk
Figure 11: AppleTalk Screen
AppleTalk zone
This determines which Apple systems can gain access to this printer.
Printer Object
Type
These are text fields, used to describe the printer driver used for
each port. The LevelOne Printer Server is designed to work with
LaserWriter (or 100% compatible) printers.
Communication
Protocol
Sets whether the port uses ASCII or Binary Communication
Protocol.. The default is Binary.
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
NetBEUI
Figure 12: NetBEUI Screen
Domain Name
Response Time
Enter the designated work group to be serviced by the LevelOne
Printer Server. This field is not case sensitive, so names with
different case will be considered to be the same name.
Set how fast jobs are sent to the printer. The default value of zero
(0) delay should be increased only if your printer cannot cope with
no delays.
Abort Print Job
if Error
YES terminates a print job if a printing error occurs. NO (default)
will try to continue but may cause print errors. If print errors occur,
try setting this value to YES.
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
The NetWare screen will not be available WPS-0100 and WPS-0100USB.
Figure 13: NetWare Screen
General
NetWare Mode
Select LevelOne Printer Server or Remote Printer, as appropriate.
The default is LevelOne Printer Server.
Frame Type
Select the frame types used by your network. (Ethernet 802.2,
Ethernet 802.3, Ethernet SNAP, and Ethernet II) By default, all
frame types are enabled.
Remote Printer Mode
Novell LevelOne
NetWare LevelOne Printer Server to service the LevelOne Printer
Printer Server for P1 Server's parallel port 1.
Novell LevelOne
NetWare LevelOne Printer Server to service the LevelOne Printer
Printer Server for P2 Server's parallel port 2 (P2), if fitted.
LevelOne Printer Server Mode
NDS Tree Name
(NDN mode only)
The File Server's NDS tree name. (root name)
LevelOne Printer
Server
Path to the NDS Context. This does not include the Context itself,
and each OU should be separated by a period.
NDS Context
(NDS Mode only)
e.g.
department.company
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
Master File Server
(Bindery Mode only)
Name of the LevelOne Printer Server's master file server.
NetWare Password
The password on the NetWare Server. The LevelOne Printer
Server device needs this password to connect to the NetWare
server.
Job Notification
The options are:
·
Job notification at only the workstation where the print job
originated.
·
Job notification at all workstations that you have logged into.
Polling Queue
Interval
Defines how often the LevelOne Printer Server will poll the
queues to be serviced.
SNMP (Simple Network Management Protocol)
Figure 14: SNMP Screen
SysContact
SysLocation
Text Field - Name of the contact person.
Text Field - Location of the contact person.
Management Stations
Select the Management station (1..4), and click the Get Data button to
Station No.
update the display for the selected item.
IP Address
Enter the IP Address of the management station, which has the SNMP
program installed.
Community
Access
This is a text field. Enter the name of the community.
Select the desired level of access.
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Trap Receivers
Select the Trap Receiver number (1..4), and click the Get Data button
Receiver No.
to update the display for the selected item.
IP Address
Enter the IP Address of the Trap Receiver, which will be sent the
Trap message.
Community
Enable
This is a text field. Enter the name of the community.
Check to enable; select the severity level.
Note: Currently, all traps are level 1.
TCP/IP
Figure 15: TCP/IP Screen
IP Address
IP Address assigned to this device. If using dynamic IP Addresses
(DHCP, BOOTP, rarp), this should be left at 0.0.0.0.
Subnet Mask
(Network Mask)
If the Router (Gateway) Address is 0.0.0.0, the Subnet Mask should
also be left at 0.0.0.0. If you have a router, enter the Subnet mask for
the segment to which the LevelOne Printer Server is attached.
Gateway
Address
If your network segment has a router or gateways, enter its IP
Address here. Otherwise, leave the address as 0.0.0.0.
Connection
Delay before
reconnection
attempts
Sets how long the LevelOne Printer Server should wait before
retrying a TCP/IP connection which is lost. Allowable values are
from 0 to 255 seconds, with 2 as the default.
Number of
reconnection
attempts
Set how many attempts at reconnection will be made. After that, the
TCP/IP session will be terminated.
Allowable values are from 0 to 255, with 254 as the default.
Page 38
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Server
Figure 16: Configure Server Screen
LevelOne Printer
Server Name
Change the default name if you wish. The new name mu st not
contain any spaces or blanks.
Enter the device password, and again in the Verify field. Once a
password is entered, it is required in order to gain access and
change the configuration.
Password
Enable Protocols
Non-TCP/IP protocols may be disabled if they are not required on
your LAN.
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Configuration
On the WPS-0100 and WPS-0100USB, this Wireless screen will be available.
The settings on this screen must match the other Wireless stations in order for communication
to occur.
Figure 17: Wireless Screen
Page 40
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration
Regulatory
Domain
It is illegal to use this device in any location outside of the regulatory
domain.
Station name
This is the same as the Device (Host) Name on the WAN screen. On
your PC, some Wireless status screens may display this name as the
Access Point in use.
SSID
(ESSID)
To communicate, all Wireless stations MUST use the same
SSID/ESSID.
The default value is null.
Note! The SSID is case sensitive.
Channel No.
The default Channel for the USA and Canada is 3.
Select the value you wish to use on your Wireless LAN. If you
experience lost connections and/or slow data transfers you may need to
experiment with different channels to see which is the best.
Network Type
Select the correct value for your Wireless LAN.
·
·
·
802.11 Ad-hoc mode is used when there is no Wireless Access
Point, and each Wireless station communicates directly with other
Wireless stations. This is the current standard.
Ad-hoc mode is used when there is no Wireless Access Point, and
each Wireless station communicates directly with other Wireless
stations. This is the older standard.
Infrastructure mode is used when each Wireless station connects to
the Wireless Access point. This also provides access to the wired
LAN.
Link Info
Button
Click this button will open the sub screen.
WEP Data Privacy
Off
If OFF (default), data is NOT encrypted before being transmitted.
64 Bit
Encryption
If selected, data is encrypted, using the default key, before being
transmitted.
The receiving station must be set to 64 Bit Encryption, and have the
same Key value in the same position in its key table. Otherwise, it will
not be able to decrypt the data.
Default Key
Select the key you wish to be the default. Transmitted data is ALWAYS
encrypted using the Default Key; the other Keys are for decryption only.
Key Table:
This table is used when Encrypting and Decrypting data. All stations,
including this Access Point, always transmit data encrypted using their
default key. The key number (1, 2, 3, 4) is also transmitted. The
receiving station will use the key number (1, 2, 3, 4) to determine which
key value to use for decryption. If the key value does not match the
transmitting station, decryption will fail.
The easiest way to ensure there are no problems is to have every Station,
including the Access Point, use the same key table (all entries identical).
Then, it does not matter which key is used as the default key.
Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
128 Bit
Encryption
If selected, data is encrypted using the key before being transmitted. The
receiving station must be set to use 128 Bit Encryption, and have the
same Key value. Otherwise, it will not be able to decrypt the data.
Key
Enter the key value you wish to use. Other stations must have the same
key
WEP
Options are "Open System" or "Shared Key".
Authentication
Some Wireless cards do not support both methods. Check your Wireless
card's documentation to determine the correct value.
Ensure that all Wireless stations use the same setting as the Access Point.
Page 42
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Screens
Server Status
This screen shows server system data and the current settings for all of the other screens. It is
read-only; no data can be input on this screen.
Printer Ports
This screen displays the current status of each port. For each port, the following data is listed:
·
Connected Printer- the model name of the printer connected to the port, if the printer
name is known. (If the printer is not bi-directional, this information is unavailable.)
·
·
Status - the current status of the printer (On-line, Off-line, Out of paper)
Printing Information - this will show either Idle or Printing.
Serial Port Configuration
If fitted, the Serial Port Screen can be accessed by clicking the Configuration button on the
Printer Ports Screen.
If the default values do not work, check your serial printer to determine what settings should be
used.
Logical Printers
Logical Printers (ports) can be used under Unix or NetWare. For each Logical Printer, the
following fields are available:
Logical Printer
(Port)
Select the Logical Printer Port you wish to configure. (L1 to L3 or
L1 to L8, depending on your model)
Click the Get Data button to update the display with the current data
for the selected logical printer.
Port
Select the Printer Port which the Logical printer will use.
Pre-string
The printer control string (in hex) to be sent to the printer before
each print job. This string cannot exceed 15 characters.
Post String
The printer control string (in hex) to be sent to the printer after each
print job. This string cannot exceed 15 characters.
Convert LF to
CR+LF
If checked, LF (line feed) characters are changed to CR+LF (carriage
return + line feed).
Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
Special Features
This chapter covers the special features of the LevelOne Printer Server.
Overview
The LevelOne Printer Server has four (4) special features:
·
·
·
·
Some LevelOne Printer Servers support IPP (Internet Printing Protocol).
All model support the proprietary Internet Mail Printing system.
SNMP (Simple Network Management Protocol) is supported by all models.
Wireless Station - supported by WPS-0100 and WPS-0100USB only.
Internet Printing Protocol (IPP)
IPP (Internet Printing Protocol) is a new standards-based system to allow remote printing from
a PC to any accessible printer. Normally, the printer will be attached to a computer or other
device which functions as an IPP Server.
For client PCs, it is necessary to install a compatible IPP Client program. The Client must also
know the IP Address or URL or the IPP Server.
IPP Server Configuration
The LevelOne Printer Server contains the necessary firmware to act as an IPP Server. No
additional configuration is necessary. However, the following requirements must be met.
·
The LevelOne Printer Server must have a valid IP Address. For printing via the Internet,
the LevelOne Printer Server's IP Address must be external (allocated by your ISP), rather
than an IP Address on your local LAN.
·
·
·
Any Router, Gateway or Firewall linking your LAN to the Internet must NOT block the
IPP protocol.
You must advise clients of the correct URL or IP Address of the IPP Server. To use a URL
rather than an IP Address, you need to register the domain name for the URL.
Unless clients are using Windows 2000, you must provide your clients with the supplied
IPP Client software. If it is not convenient to provide the CD-ROM, supply the
IPP_CLIENT.EXE file, located in the IPP folder.
Page 44
Download from Www.Somanuals.com. All Manuals Search And Download.
IPP Client Setup - Windows 95/98/ME/NT 4.0
The IPP Client Software can be installed on any of the following systems:
·
·
Window 95/98/ME
Windows NT 4.0
Installing from the CD-ROM
1. Insert the CD-ROM in your drive. If the program does not start automatically, run the
SETUP program in the top-level folder.
2. Follow the prompts until you reach the Select Installation screen, and select IPP Client.
3. At the next screen, select the Install IPP Client option.
4. Click Next, and step though the remaining screens to complete the installation.
Installing using IPP_CLIENT.EXE
1. Run this program to unzip the included files.
2. The IPP Setup program will then run.
3. Follow the prompts to complete the installation.
IPP Client Configuration (Windows 95/98/ME/NT 4.0)
1. Run the "Add IPP Port" program entry created by the installation. A screen like the
following will be displayed.
Figure 18: IPP Port
2. If Internet access from your location is via a Proxy Server, check Access IPP Server via
Proxy Server, and enter details of your Proxy Server. (This will be the same as your
Browser configuration.)
3. Enter the IP Address or URL of the IPP Server.
4. Click Select Device Port to view the available ports on the IPP Server, and select the
appropriate port. A connection to the IPP Server will be established at this time.
Page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click Save to create the IPP port on your system. You will see a message confirming that
the port has been created, then the following dialog:
Figure 19: Select Printer for IPP Port
6. Either select an existing printer to use the new port, and click OK.
OR
Click the Add New Printer button to create a new printer to use the IPP port. This will start
the Add Printer wizard. Follow the prompts to complete the process. Ensure that the new
printer uses the IPP port.
Installation is now complete.
·
·
To create additional IPP Ports, repeat the entire procedure.
The Proxy Server and other options are set individually for each IPP Port.
Changing the IPP Port Settings
After the IPP port is created, you can reach the screen shown in Figure 18: IPP Port using the
Windows Port Settings button:
1. Open the Printers folder (Start - Settings - Printers)
2. Right-click the IPP Printer, and select Properties.
3. Locate and click the Port Settings button (Details or Port tab, depending on your version
of Windows).
There are 2 settings - Retry Interval and Retry Count - which can be adjusted if you have
problems connecting to the IPP Server.
·
Retry Interval sets the time interval (in seconds) between connection attempts. Increase
this number if you have a poor connection, or the remote server is very busy.
·
Retry Count sets how many connection attempts will be made. Increase this number if
you have a poor connection, or the remote server is very busy.
Page 46
Download from Www.Somanuals.com. All Manuals Search And Download.
IPP Client Setup - Windows 2000
Windows 2000 has its own IPP Client, and there is no need to install the supplied IPP Client
Software. To use Windows 2000's IPP Client with the LevelOne Printer Server, follow this
procedure:
1. Start the Add Printer wizard.
2. Select Network Printer, and click "Next" to see the Locate your Printer screen, as shown
below.
Figure 20: Windows 2000 - Locate your Printer
3. Select Connect to a printer on the Internet or on your Intranet, and enter the URL of the
IPP Server as follows, where ip_addressrepresents the IP Address of the IPP Server,
and 631 is the port number.
ip_address:631/ipp/P1
ip_address:631/ipp/P2
ip_address:631/ipp/P3
Parallel Port 1
Parallel Port 2 (if exists)
Parallel Port 3 (if exists)
These entries are case sensitive. They must be
entered as shown, with "ipp" in lower case, and
P1, P2 and P3 in UPPER case.
4. If the connection can be established, and the printer on that port is on-line, the following
dialog will be displayed.
Page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 21: Windows 2000: No printer driver
5. Click "OK", and then select the printer manufacturer and model to match the printer
connected to the port on the IPP Server.
6. Click "Next", and complete the Wizard.
The IPP printer is now ready for use.
Using IPP Printers
The IPP Printer can be selected and used like any other Windows printer. If the IPP Server is
not on your network, your Internet connection needs to be active.
If you wish to check the availability of the remote IPP Server, you can use the Query IPP
Printer program installed with Add IPP Port.
An IPP Server may be unavailable for any of the following reasons:
·
·
It is powered off.
A printer problem has caused the IPP Server to cease responding, and a restart (reboot) is
required.
·
·
·
The Server's IP Address has changed.
The Internet connection for the IPP Server is down.
Network congestion causes the connection attempt to time out.
If using the supplied IPP Client software, there are 2 settings - Retry Interval and Retry Count -
which can be adjusted if you have problems connecting to the IPP Server.
See the previous section Changing the IPP Port Settings for details.
Page 48
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet Mail Printing
The Internet Mail Printing System allows users to print data to your printer across the Internet.
Users send the Internet LevelOne Printer Server an E-Mail, with the print job normally sent as
an attachment to the E-Mail. The LevelOne Printer Server will retrieve the E-Mail and print it.
System Requirements
Mail Server
·
·
Accessibility. The Mail Server must be accessible by the intended clients or users.
Normally, this means a permanent connection to the Internet.
Protocols. The Mail Server must support the POP3 and SMTP protocols. The Internet
Printing System uses these protocols and the most common E-Mail formatting standards:
·
·
MIME (Multipurpose Internet Mail Extensions)
Base64 Encoding (for mail attachments)
Internet LevelOne Printer Server
·
·
TCIP/IP Protocol. The LAN must use the TCP/IP protocol.
Mail Server Access. The LevelOne Printer Server must be able to access the Mail Server
using a single IP address.
·
Mail Account. The LevelOne Printer Server must have a Mail Account. Users print by
sending an E-Mail to this mail account.
User (Client) Requirements
·
·
Internet Connection. Either through a LAN, or dial-up.
E-Mail address. This is used to notify the user that their print job has been done, or if
there any problems.
·
·
Printer Driver. Users must have a printer driver which matches the printer connected to
the remote Internet LevelOne Printer Server.
Print Capture Software. To print more than plain text, users require InterNet Printing
Port software to capture the print job and convert it into an E-Mail attachment.
The Internet Printing Port software is available for the following operating systems:
·
·
Microsoft Windows 95
Microsoft Windows NT 3.51 or later.
Page 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet Mail Printing Configuration
The LevelOne Printer Server must be configured with the data in the following table.
The supplied BiAdmin utility program, or the Web interface (on 100BaseT models) can be
used to set the following entries on the TCP/IP screen.
Mail Server IP Address
Mail Account
The IP Address of the E-Mail Server used by the LevelOne
Printer Server.
The name of the E-Mail Account used by the LevelOne
Printer Server.
Mail Account Password
Check Mail Interval
Enter the password for the above Mail Account here.
Sets how often to check for mail. Values range from 0 to
65,535 minutes, with 0 meaning a continuous connection
and 1 as the default.
Print Banner
If YES (default), a banner page is printed to identify the
owner of the print job.
Redirect Mail Account
Default Printer Number
Print every E-Mail
Jobs which can not be printed will be sent to this account. If
blank, unprintable jobs will be discarded.
Printer number for all Internet print jobs. Only one port can
be selected. Users on the LAN can also use this port.
If ON, then all E-Mail received is printed. Otherwise, only
E-Mail from the InterNet Printing Port will be printed.
Activate Response Mail
If YES, all print jobs receive an E-Mail response. If NO,
only users who set this option in their InterNet Printing Port
software receive an E-Mail.
Printer Model ID String
This text field identifies the printer used for Internet
printing. This value is sent to remote users upon request.
Page 50
Download from Www.Somanuals.com. All Manuals Search And Download.
User Software
The software provided for remote users (InterNet Printing Port) should be installed by
everyone intending to use Internet printing. Otherwise, remote users can print correctly only if:
·
They send an E-Mail directly to the LevelOne Printer Server Mail Account, using their
normal E-Mail application.
·
·
The E-Mail contains plain text only.
The Internet LevelOne Printer Server is configured with Print every E-Mail ON.
Installation of the InterNet Printing Port software will create a new printer port. After attaching
the correct printer to this port, users can print to the Internet Printer using any Windows
application.
Installation - User Software
1. Run the InterNet Printing Port installation program SETUP.EXE
2. Default values for the installation are:
·
·
Directory - C:\Program Files\Internet_Printer
Start Menu folder - InterNet Printing Port Driver
3. You will then see the Configure Port screen, as shown in the following screenshot.
Figure 22 InterNet Printer Port
4. The following data must be provided.
Port Name
Enter a descriptive name (e.g. "WAN") for the new
printer port.
Page 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Printer
E-mail Address
The E-Mail address for the Internet printer. Your print
jobs will be sent to this E-Mail address.
Mail Server Name
or IP Address
This is the name or IP Address of your Mail Server. If
you are on a LAN, ask the LAN Administrator. If using
a dial-up connection, use the data provided by your ISP.
Your Internet
The normal address that people use to send you E-mail.
E-mail Address
Retry Interval
(Seconds)
If unable to connect to the E-Mail server, retry after this
time period (1 to 255 seconds, 30 is usually OK).
Reply Notification
Mail
Check to receive an E-Mail when your print job has
been processed.
5. On completion, a new printer port will have been created.
Using the new Port
The Windows Control Panel is used to connect the correct printer to the InterNet Printing Port.
In Windows 95/NT, the procedure is:
1. Select the Printer which matches the remote printer, then choose Properties, as shown in
the example below.
Figure 23 InterNet Printer Properties
2. Select the new port - WAN (InterNet Printer) in the example - as the port for this printer.
·
·
·
If you do not have the correct printer driver, or you wish to create another printer
using an existing driver, use the Windows Add Printer facility.
Using the Windows Port Settings or Configure Port facility will reveal the same
Configure Port screen shown in Figure 22 InterNet Printer Port on page 51.
If you wish to print to multiple Internet Printers, use the Windows Add Port facility to
add a new InterNet Printer port. Ensure that the correct data is entered in each port,
and that each port has a unique name.
Page 52
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the Printer Driver
To make sure that the correct printer driver for the remote printer is installed on your system,
you can use the InterNet Printing Port to send an E-Mail to the Internet Printer. The procedure
is as follows:
1. Connect your default printer to the InterNet Printing Port.
2. Check that "Reply Notification Mail" in the InterNet Printing Port is ON.
3. From Notepad or another text editor, print a short message (e.g. "This is a test print") to
the Internet Printer.
You will receive a reply E-Mail containing the "Printer ID" which will identify the printer
attached to the LevelOne Printer Server. If this does not match the printer driver you are using,
install the correct printer driver.
Printing through the Internet
1. Create or open the document you wish to print.
2. Select the Printer connected to the InterNet Printing Port.
3. If you do not have a permanent Internet connection, establish a connection now. (Note:
The InterNet Printing Port will NOT establish a dial-up connection, but it will send the E-
Mail the next time you are connected.)
4. Print the document.
5. The InterNet Printing Port will generate an E-Mail and send it to the remote printer. The
document will be encoded and sent as an attachment to the E-Mail. You will see a progress
screen similar to the example below:
Figure 24 InterNet Printing Progress
6. Close the Internet connection if you opened it in Step 3.
7. If the "Notify after print job" option is set, you will receive an E-Mail when your job is
printed.
Canceling a Print Job
Users cannot cancel a Print Job once it has been sent, but Print Jobs can be canceled at the
LevelOne Printer Server. In BiAdmin, the Control - Abort Mail Print Job menu option can be
used to cancel a print job which has already started printing.
Page 53
Download from Www.Somanuals.com. All Manuals Search And Download.
SNMP
The LevelOne Printer Server supports SNMP (Simple Network Management Protocol). This
allows network supervisors to monitor and control the LevelOne Printer Server using network
management platforms such as HP OpenView, IBM SystemView, etc.
The appropriate MIB file must be imported into your SNMP management program using the
Import-Compile command. Check your management program for details on this procedure.
The MIB files are provided in the Mib folder on the CD-ROM, as follows:
Mib1p.mib
Mib2p.mib
Mib2p1s.mib
Mib3p.mib
Single port models.
Models with 2 parallel ports
Two parallel ports, 1 serial port model.
Models with 3 parallel ports
Configuring the LevelOne Printer Server for SNMP
Before using a SNMP Management station to manage the LevelOne Printer Server, the
following settings should be assigned to it, in addition to the IP Address, Gateway Address,
and Subnet Mask.
SNMP Settings
SysContact
SysLocation
Text Field - Name of the contact person.
Text Field - Location of the contact person.
Up to 4 Management Stations can be entered.
Management Station
IP Address(s)
Trap Receiving
IP Address(s)
Up to 4 Trap Receiving Stations can be entered.
Management Station Settings
For each Management Station, the following fields are available:
Access Permission
Community String
Options are:
Read Only
Read/Write
Not Accessible
Leaving this blank will disable management by this station.
Trap Receiving Station Settings
For each Trap Receiving Station, the following fields are available:
Community String
Trap Enable
Leaving this blank will disable management by this station.
Use this option to Enable/Disable Trap Receiving by this
station.
Trap Severity
In this version, all traps are level 1.
Page 54
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Configuration
Models WPS-0100 & WPS-0100USB
The WPS-0100 and WPS-0100USB are Wireless stations, NOT access points. Like all other
Wireless stations, they have 3 modes:
·
802.11 Ad Hoc mode - no Access Point is used, Wireless stations communicate directly
with each other. This is the current standard.
·
Ad Hoc mode - no Access Point is used, Wireless stations communicate directly with each
other. This is the older standard.
Of the two (2) Ad-hoc modes, "802.11 Ad Hoc" mode is
recommended. If your Wireless LAN Card doesn't provide "802.11
Ad Hoc" mode, try "Ad Hoc" mode on the PC and "802.11 Ad
Hoc" on the WPS-0100/7800. If this fails, select"Ad-hoc" mode on
the LevelOne Printer Server.
·
Infrastructure (Default) - all Wireless stations connect to the Access Point. This allows
connection to both other Wireless stations and the wired LAN.
The WPS-0100 and WPS-0100USB do NOT allow both a LAN
connection and "Infrastructure" mode.
In "Infrastructure" mode, connecting a LAN cable will disable the
Wireless interface.
To use the LAN interface, "Ad-hoc" mode must be used.
Required configuration
Ad-hoc Mode
Infrastructure Mode
SSID
Must match the other Wireless stations, Must match the Access Point.
unless the SSID is null or "any".
If its SSID is null or "any", a Wireless
station can join any Ad-hoc group.
But since the WPS-0100 and WPS-
0100USB are fixed devices (rather than
roaming), their SSID should not be
null or "any".
It's recommended to assign value to
SSID for WPS-0100 and WPS-
0100USB.
Channel
Should match the other Wireless
stations.
Access Point sets the Channel
used.
However, when joining an existing ad-
Wireless stations
hoc group, a Wireless station must use automatically locate the
the Channel in use, rather than its own
Channel.
correct channel.
For a device like the WPS-0100 or
WPS-0100USB0 in a fixed location, it
is best to set them to the Channel
providing the least interference and
best performance.
Page 55
Download from Www.Somanuals.com. All Manuals Search And Download.
WEP Settings
Must match the other Wireless stations. Must match the Access Point.
Page 56
Download from Www.Somanuals.com. All Manuals Search And Download.
Two (2) methods are available to perform the required configuration:
·
·
BiAdminmanagement utility program - see below for details.
Web-based setup - see Chapter 6 for details.
BiAdmin Wireless Screen
Installation and use of the BiAdmin Windows utility is described in Chapter 5.
Clicking the Wireless icon, or selecting Configuration - Wireless on the menu, will display the
following screen.
Figure 25: Wireless Screen
Regulatory
Domain
It is illegal to use this device in any location outside of the regulatory
domain.
Station Name
SSID
The name used to identify this Wireless station.
·
·
·
If using an ESS (Extended Service Set, with multiple access
points) this ID is called an ESSID (Extended Service Set
Identifier).
To communicate, all Wireless stations MUST use the same
SSID/ESSID. Change this value, or change the other Wireless
stations, to ensure each Wireless station has the same value.
The default value is "null", so the Wireless station can join any
Ad-hoc group.
Note! The SSID is case sensitive.
Page 57
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel No
To communicate in "802.11 Ad-hoc" or "Ad hoc" mode, all Wireless
stations MUST use the same Channel number.
·
·
·
If using "802.11 Ad-hoc" or "Ad-hoc" mode, select the value you
wish to use on your Wireless LAN.
If using "Infrastructure" mode, the Channel is selected
automatically, to match the Channel used by the Access Point.
If you experience interference (shown by lost connections and/or
slow data transfers) you may need to experiment with different
channels to see which is the best.
Network Type
Select the correct value for your Wireless LAN.
·
·
·
802.11 Ad-hoc mode is used when there is no Wireless Access
Point, and each Wireless station communicates directly with other
Wireless stations. This is the current standard.
Ad-hoc mode is used when there is no Wireless Access Point, and
each Wireless station communicates directly with other Wireless
stations. This is the older standard.
Infrastructure mode is used when each Wireless station connects
to the Wireless Access point. This also provides access to the
wired LAN.
Encryption
WEP Disabled/
Enabled
If Disabled (default), data is NOT encrypted before being transmitted.
If Enabled, you must provide either the 64 Bit key table or the 128 Bit
keys, as described below. The key is used to encrypt the data before
transmission.
64 Bit
·
If selected, data is encrypted, using the default key, before being
transmitted. The receiving station must be set to 64 Bit
Encryption, and have the same Key value in the same position in
its key table. Otherwise, it will not be able to decrypt the data.
·
Default Key - select the key you wish to be the default.
Transmitted data is ALWAYS encrypted using the Default Key;
the other Keys are for decryption only.
Key Table:
This table is used when Encrypting and Decrypting data. All stations,
including this Access Point, always transmit data encrypted using their
default key. The key number (1, 2, 3, 4) is also transmitted. The
receiving station will use the key number (1, 2, 3, 4) to determine
which key value to use for decryption. If the key value does not match
the transmitting station, decryption will fail.
The easiest way to ensure there are no problems is to have every
Station, including the Access Point, use the same key table (all entries
identical). Then, it does not matter which key is used as the default
key.
128 Bit
If selected, data is encrypted using the key before being transmitted.
The receiving station must be set to use 128 Bit Encryption, and have
the same Key value. Otherwise, it will not be able to decrypt the data.
WEP
Options are "Open System" or "Shared Key".
Authentication
Some Wireless cards and Access Points do not support both methods.
Check your documentation to determine the correct value to use.
Page 58
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Link Info Screen
After clicking the "Link Info" button on the Wireless Screen, a screen like the example below
will be shown.
Figure 26:Link Info Screen
State
This indicates which access point is currently in use.
The current channel which has been used.
Current Channel
Current TX Rate
Throughput (Tx )
Throughput ( Rx )
Link Quality
The current transmitting speed.
This will show how much data has been transmitted per second.
This will show how much data has been received per second.
This indicates the quality of the Wireless connection
This indicates the strength of the Wireless signal being received.
Signal Strength
The "Link Quality" and "Signal Strength" data is not
available if using "Ad-hoc" or "802.11 Ad-hoc" mode.
Page 59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8
Troubleshooting
This chapter describes some problem situations, which may arise, and the solutions to
them.
Overview
If you encounter printing difficulties, please refer to the appropriate section.
If, after following the advice in these documents, the LevelOne Printer Server still does not
function properly, please contact your dealer for further advice.
Hardware & LAN Problems
Problem No. 1
Solution No. 1
Problem No. 2
Solution No. 2
All the LevelOne Printer Server's LEDs are off.
Check the power supply or power connection.
LevelOne Printer Server's status light continuously stays lit.
Reset LevelOne Printer Server by unplugging the power supply and
plugging it back in.
Problem No. 3
Solution No. 3
Problem No. 4
Solution No. 4
Leve lOne Printer Server's status light and power light stay on
continuously and do not turn off.
Reset the LevelOne Printer Server by unplugging the power supply or by
pushing the reset push button, if fitted.
The LevelOne Printer Server unit can not be found on the LAN, so
configuration is not possible.
If using 10/100BaseT:
·
·
Check the Hub. The link LED for the port to which the LevelOne
Printer Server is connected should be ON. If it is Off, there is a
problem in the network cable.
On the LevelOne Printer Server, check the LED(s) next to the
connector. If the LED is not ON (or neither LED is On, if there are
2), the network connection is not working.
Check the Ethernet cable and connectors. If they seem OK, set the
DIP Switches of the LevelOne Printer Server to match your LAN
environment.
If using TCP/IP:
·
Ensure that there are no routers between the LevelOne Printer
Server and the PC used for configuration.
·
Ensure that the PC used for configuration has the TCP/IP network
protocol installed. Test its network connection by seeing if you can
locate other LAN devices from the PC. (e.g. Use Network
Neighborhood and try to browser the network.)
Problem No. 5
I am using DHCP, and getting an IP Address conflict involving the
Page 60
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Printer Server.
Solution No. 5
If the LevelOne Printer Server is left on, but the DHCP server is turned
off, then the LevelOne Printer Server will retain its IP Address without
the DHCP Server being aware of it. Simply reset the LevelOne Printer
Server so it will obtain a new IP Address.
This problem would also arise if you assigned static IP Address, which is
within the range used by the DHCP server. If so, use another address
which is NOT within the range used by the DHCP server.
AppleTalk (Macintosh)
Problem No. 1
Why do I get an incorrect printout?
Some possible reasons are:
Solution No. 1
·
You may have chosen Binary encoding to print the file. Try to use
ASCII encoding.
·
Some of the fonts, which are in your print file may not be
supported by the printer. Try selecting LaserWriter 7 instead of
LaserWriter 8.
Problem No. 2
Can't find the LevelOne Printer Server's name in the Chooser.
Solution No. 2
Try the following:
1. Make sure that AppleTalk is on (the button next to Active is
highlighted in the Chooser).
2. Make sure the printer has been on and in the READY state for a
few minutes.
3. Make sure the printer has not been renamed since its last
appearance in the Chooser.
4. If the printer resides on a network with multiple zones, make sure
the correct zone is selected from the AppleTalk Zones box in the
Chooser.
Problem No. 3
My document didn't print to the right printer.
Solution No. 3
Check the following:
·
Another LevelOne Printer Server with the same name may have
received your print job. Use the PSTOOL to reconfigure your
LevelOne Printer Server name and ensure all LevelOne Printer
Servers have unique names.
·
Make sure your application output encode is set to ASCII. If not,
change it to ASCII.
Problem No. 4
Solution No. 4
Problem No. 5
Solution No. 5
My file doesn't print with the correct fonts.
Try changing your printer driver to LaserWriter 7.
My EPS file doesn't print with the correct fonts.
This is a problem that occurs in some application programs. Try
downloading the fonts contained in the EPS file before printing the
saved EPS file.
Page 61
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem No. 6
I can't select the "Remaining from:" item in the print dialog box.
Solution No. 6
If you have selected the Layout value, "2 Up", or "4 Up", you cannot
access the Remaining from item. Choose other selections.
Problem No. 7
A cover page prints either on the first or the last page of the
document.
Solution No. 7
Select one of these solutions:
·
·
Turn the cover page feature off.
Insert extra page breaks in your document to avoid the cover page
printing on the first or last page of your document.
·
Install the Apple LaserWriter 7 driver. You are having trouble
printing with the Apple LaserWriter 8 driver.
Problem No. 8
Why do I have trouble printing with the LaserWriter 8?
Solution No. 8
Your application software may not be compatible with the LaserWriter
8 driver or your system may not meet the requirements of the
LaserWriter 8 driver. Use the Apple LaserWriter 7 driver instead.
Problem No. 9
The colors on my printed output do not match the colors on my
computer screen.
Solution No. 9
When the printer receives a color file, it tries to match the printed
output color to the screen color. Sometimes the printer cannot match up
the colors as closely as wanted. To alleviate this problem, perform the
following steps:
·
Choose "Calibrated Color/Grayscale" in the Print pop-up menu in
the Print Options dialog box. The printer will make adjustments
to match the colors.
·
Check your monitor to make sure all settings (for example,
brightness) are adjusted correctly.
Problem No. 10
When I send a print job, I get a PostScript Command error or no
print out.
Solution No. 10
Check the communication protocols. The computer, LevelOne
Printer Server and printer must all be configured to the same
communication protocol.(either Binary or ASCII).
To configure your system:
1. Choose which protocol you are going to use. You should check
your printer; it may not give you a choice.
2. Set your printer to the correct protocol.
3. Use the computer's Print submenu to configure your computer to
use the protocol you have chosen.
4. Configure the LevelOne Printer Server to use the same protocol as
the printer and computer.
Page 62
Download from Www.Somanuals.com. All Manuals Search And Download.
Novell NetWare
Problem No. 1
My LevelOne Printer Server cannot print the jobs sent to the print
queue.
Solution No. 1
Try the following:
1. Check if the printer attached to the LevelOne Printer Server is on-
line.
2. Check if your LevelOne Printer Server is logged into the file server
(See Problem 2 below.).
3. Check the current status of the queues used by the LevelOne Printer
Server, and ensure the queues are active.
4. Check if the NetWare printer number is correct.
0 = parallel port 1 of the LevelOne Printer Server.
1 = parallel port 2 of the LevelOne Printer Server.
2 = serial port or parallel port 3.
5. Check to see if the LevelOne Printer Server is a static queue server
to the queue.
Locate the LevelOne Printer Server Object, and check the Queues
Serviced by Printer. Ensure that the correct queues are on the list.
6. The total number of queues to be serviced may be over the limit of
56. If so, reduce the number of queues.
Problem No. 2
My LevelOne Printer Server is configured as a Novell LevelOne
Printer Server, and cannot log in to a File Server.
Solution No. 2
The following steps may solve this problem:
1. Check the Novell file server's name. If it is over 20 characters long,
rename it using no more than 20 characters.
2. Check that the LevelOne Printer Server's configuration data,
especially the password, is correct.
3. Check the NetWare server. If using Bindery mode, check the master
file server to see if the login status of the LevelOne Printer Server is
Ready. If it is not, check the error message and perform the required
corrective action.
4. If the LevelOne Printer Server is servicing more than one file server,
check to see that all required file servers are in the list of "File
Servers To Be Serviced". If not, insert the required file server name
to the list.
Page 63
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows Printing Problems
Problem No. 1
When I tried to install the Printing software for Peer-to-Peer
printing, I received an error message and the installation was
aborted..
Solution No. 1
This may be caused by an existing installation of the printer port
software. Before attempting another installation:
·
·
Remove the existing installation
Restart your PC
To remove an existing printer port installation:
1. Open Start - Settings - Control Panel - Add/Remove Programs
2. Look for an entry with a name like "Shared Port", "Shared Printer
Port", "LevelOne Printer Server Driver" or " LevelOne Printer
Server Port".
3. Select this item, click "Add/Remove", and confirm the deletion.
Problem No. 2
On Windows 95, I installed the Print Port Driver for Peer-to-Peer
Printing, but when I selected a port on a LevelOne Printer Server
and clicked "Add", the printer was not installed.
Solution No. 2
Try installing the Printer using the standard Windows tools, as follows:
1. Start the Add Printer Wizard.
2. Select Network Printer when prompted "How is the printer attached
to your Computer?", and click Next.
3. When prompted for the Network Path or Queue, enter a dummy
value such as shown below. (Do NOT select Yes for "Do you print
for MS-DOS programs?")
4. The printer wizard will display a message stating that "The Network
Printer is off-line". This is OK. Continue the Add Printer Wizard
until finished.
5. Go to the Printers folder (Control Panel-Printers). The printer icon
will be grayed out indicating the printer is not ready.
6. Right-click the Printer, and select Properties. Then select the Details
Page 64
Download from Www.Somanuals.com. All Manuals Search And Download.
tab, as shown below.
7. Click the Add Port button. On the resulting screen, select Other,
then LevelOne Printer Server, as the port to add, as shown below.
8. Click OK to see the Print Port Configuration screen, as shown
below.
Page 65
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Click the Browse Device button, select the desired LevelOne Printer
Server, and click OK.
10. Click OK to return to the Printers folders, and right-click on the
Printer. Ensure that the Work off-line option is NOT checked.
The Printer should no longer be grayed out, and is ready for use.
Problem No. 3
I connected and configured a WPS (Windows Printing System)
printer as described, but I can't get the print job to print.
Solution No. 3
Printer drivers for WPS printers poll the printer before sending print
data. Since the printer is networked, the printer is not found and no data
is sent. The solution is to add your printer as a network printer as
described in Solution 1 above.
Note: The screens shown in Solution 1 are from Windows 95. Other
versions of Windows may look slightly different, but the process is
identical. If using Window NT or 2000, do NOT enable Sharing for the
printer.
Problem No. 4
When printing from some software applications such as Power
Point, it takes a long time and the print out is incorrect.
Solution No. 4
The problem is due to the printer, which is being configured to Start
printing after the first page is spooled. To change this setting:
·
·
·
·
Go to Control Panel - Printers and click on your printer.
Then select File - Properties - Details.
When the Details screen appears, click the Spool Settings button.
When the Spool Settings dialogue box appears, choose Start
Page 66
Download from Www.Somanuals.com. All Manuals Search And Download.
printing after last page is spooled and click OK.
Problem No. 5
A printing device connected to the LevelOne Printer Server port
cannot print or prints garbage.
Solution No. 5
Check the following:
·
·
·
Cable connection between LevelOne Printer Server and printer.
Serial port configuration, if a serial device.
Printer driver in the application program or Windows matches the
printer.
The Configuration button on the Printer Status screen in BiAdmin is
Problem No. 6
grayed out, even though my printer is bi -directional.
Solution No. 6
The button is unavailable if the printer is busy. You must wait until the
printer is idle.
Page 67
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
General Specifications
WPS-0100
3w max.
Power Consumption
External Power Adapter
LEDs
12V DC
4
Parallel Port
1 Centronic female DB-25
connector
Ethernet Connector
FCC / CE
10/100BaseT
Class B
WPS-0100USB
Power Consumption
External Power Adapter
LEDs
3w max.
12V DC
4
USB Port (1.1)
Ethernet Connector
FCC / CE
1
10/100BaseT
Class B
Environmental Specifications (all Models)
Operating Temperature
Storage Temperature
Shipping Temperature
Operating Humidity
Storage Humidity
0 ~ 40°C
-10 ~ 70°C
-40 ~ 70°C
10 ~ 80%
5 ~ 90%
Shipping Humidity
5 ~ 100%
Page 68
Download from Www.Somanuals.com. All Manuals Search And Download.
Parallel Port Pin Assignments
Other Models
Signal Name
- Strobe
Pin
Direction
To printer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
+Data 0
+Data 1
+Data 2
+Data 3
+Data 4
+Data 5
+Data 6
+Data 7
- ACK
To printer
To printer
To printer
To printer
To printer
To printer
To printer
To printer
To Server
To Server
To Server
To Server
To printer
To Server
To printer
To printer
Ground
+ Busy
+ Paper End
+ Select
- Auto Feed
- Error
- Init
- Select In
GND
18-25
Page 69
Download from Www.Somanuals.com. All Manuals Search And Download.
Protocol Support
Model
WPS-0100
TCP/IP
NetBEUI
NetWare
AppleTalk FTP/Telnet
v
v
v
v
v
v
WPS-0100USB
Feature Support
Model
HTTP
Setup
E-mail
Printing
IPP
JetAdmin
SNMP
WPS-0100
v
v
v
v
v
v
v
v
v
v
WPS-
0100USB
Models WPS-0100 and WPS-0100USB can also act as IEEE 802.11b Wireless Stations.
Page 70
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Approvals
Appendix B
Network Server Configuration
Windows NT Server
Preparing for TCP/IP Printing
If using Windows NT 3.51 or Windows NT 4.0, Microsoft TCP/IP Printing Support must be
installed.
·
·
If it is already installed, proceed to Adding a TCP/IP Remote Printer.
Otherwise, the procedure to install TCP/IP printing support is as follows.
Windows NT 3.51
1. Start the Network option in Control Panel. When the Network Settings dialog box appears,
click the Add Software button to display the Add Network Software dialog box.
2. Select TCP/IP Protocol And Related Components in the Network Software list box, and
then click the Continue button.
3. In the Windows NT TCP/IP Installation Options dialog box, check the TCP/IP Network
Printing Support option.
4. Click the OK button. Windows NT Setup will display a message asking for the full path to
the Windows NT distribution files. Provide the appropriate location and click the Continue
button. All necessary files will be copied to your hard disk.
5. If you did not check the Enable Automatic DHCP Configuration option in the Windows
NT TCP/IP Installation Options dialog box, you must complete all the required TCP/IP
configuration procedures manually.
6. After you finish configuring TCP/IP, the Network Settings dialog box will reappear, click
the Close button and then restart your computer for the changes to take effect.
Windows NT 4.0
1. Go to Start-Settings-Control Panel-Network.
2. Click the Service option and ensure that Microsoft TCP/IP Printing is enabled. If it is not
enabled, select the Add option and enable it as usual.
3. If you added services in step 2, reboot the computer for the changes to take affect.
Page 71
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding a TCP/IP Remote Printer
Windows 3.51
1. From the Printer menu in Print Manager, select Create Printer.
2. In the resulting dialog box, enter data as follows:
Printer Name
Enter a name (up to 32 characters). This name appears in the title
bar of the printer window.
Driver
Select the appropriate driver for the attached printer.
Enter a printer description for other network users to reference.
Select Other.
Description
Print To
3. A Print Destinations dialog box will appear after selecting Other. In the Available Print
Monitor list, select LPR Port, then OK.
4. An Add LPR compatible printer window will appear. Enter data in the fields as follows:
Name Or Address Of Host
Providing LPD
Enter the IP address of the LevelOne Printer Server.
Name Of Printer On That
Machine
Enter the appropriate logical printer number. (e.g.
L1)
5. When the Create Printer dialog box reappears, check the Share This Printer On The
Network option.
6. The resource name shown in the Share Name box can be changed if you wish. In the
Location box, you can enter information concerning the printer location. Network users
will see this information when browsing to find this printer.
7. Complete any other configuration information in the Create Printer dialog box, save and
exit.
Client PCs can now be configured as described in Chapter 4 - Client Configuration.
Windows NT 4.0
1. Go to Start-Settings-Printer and invoke the Add Printer wizard.
2. When prompted with This printer will be managed by, select My Computer and click
Next.
3. Select Add Port…, then select LPR Port and click New Port.
4. In the Name of Address of server providing lpd: Dialog box, enter the LevelOne Printer
Server's IP address.
5. In the Name of printer or print queue on that server dialog box, enter the appropriate
logical printer number (L1..L3, or L1..L8, depending on the model) as previously
configured on the LevelOne Printer Server.
6. Click OK. When returned to the Printer Ports window, simply select Close and then install
your printer driver as usual.
7. When prompted whether or not the printer will be shared, select the Sharing radio button.
8. In the Shared dialog box, enter the shared printer name. (The shared name is how other
users will see this printer.) Click OK to save and exit.
Client PCs can now be configured as described in Chapter 4 - Client Configuration.
Page 72
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 2000 Server
1. Start the Add Printer Wizard, select Network Printer, then click Next to browse for the
LevelOne Printer Server.
2. Locate and double-click the LevelOne Printer Server, select the desired port, and click
Next.
The following message will be displayed:
Figure 27: Windows 2000 Message
3. Click "OK", and select the correct Manufacturer and Model for this printer.
4. Follow the prompts to complete the installation.
5. In the Printers folder, right-click the new printer, and select Sharing.
·
Select "Shared As:" and enter an appropriate name for this printer. Users will see this
name when browsing for the printer during installation.
·
If desired, click "Additional Drivers" and install printer drivers for other versions of
Windows, such as Windows 98. This will assist users during the installation process.
6. Click OK to close this Window. Configuration is now complete.
Client PCs can now be configured as described in Chapter 4 - Client Configuration.
Novell NetWare
The LevelOne Printer Server fully supports both Bindery and NDS Novell systems.
With either Bindery or NDS, two (2) NetWare operating modes are possible - LevelOne
Printer Server and Remote Printer. LevelOne Printer Server mode is recommended.
Novell Distributed Printing Services (NDPS) under NetWare 5 is also supported.
Configuration Methods (Bindery or NDS)
The following configuration methods are available. In each case, you must be logged into the
required NetWare Server with ADMIN rights.
Also, if using Windows, Novell's Client32 should be installed on your PC. Without Client32,
only limited configuration changes can be made on the NetWare Server.
Setup Wizard
Using the Setup Wizard is recommended. This allows configuration of the LevelOne Printer
Server in NetWare LevelOne Printer Server Mode, which is the recommended system.
Page 73
Download from Www.Somanuals.com. All Manuals Search And Download.
BiAdmin
For more control and flexibility, or to use NetWare Remote Printer Mode, you can use the
supplied BiAdmin management utility. Provided you have Novell's Client 32 installed,
BiAdmin will allow you to configure the NetWare Server as well as the LevelOne Printer
Server.
·
BiAdmin is installed by the Administrator menu option on the CD-ROM.
·
·
See Chapter 5 for general information on using BiAdmin.
The NetWare Manual (in the Manual\NetWare folder on the CD-ROM) contains detailed
information on using BiAdmin with NetWare Servers.
Other Methods
If you are unable to use Windows-based programs for configuration, the following methods are
available to configure the LevelOne Printer Server:
WPConfig
PSConfig
This program requires Windows 3.1, and the IPX/SPX protocol.
Menu-based DOS program, intended only to configure the LevelOne
Printer Server for use with NetWare V2, 3 and 4.
Quickset
Command-line DOC program, intended only to configure the LevelOne
Printer Server for use with NetWare V2, 3 and 4. This program also has
a limited ability to configure the NetWare Server itself.
·
·
These programs are provided on the CD-ROM, in the Utility folder.
WPConfig has a SETUP program; the other programs need only to be copied to the
desired folder on your PC.
·
·
The documentation for these programs is provided in sub-folders of the Manual folder on
the CD-ROM.
PSConfig and WPConfig do NOT configure your NetWare Server. It is necessary to use
PCONSOLE to create the necessary print object and queues, and ensure the appropriate
users have access rights to the print queues.
Configuration Data
The LevelOne Printer Server requires the following "General" data, and the data for the mode
(LevelOne Printer Server or Remote Printer) you are using.
General
Device Name
The device name (Default Server Name) is shown on a sticker on
the base of the device. Change this if you wish. The new name
MUST NOT exceed 19 characters, nor contain any spaces.
Device Password
NetWare Mode
Frame Type
Default is NULL (no password).
LevelOne Printer Server or Remote Printer.
Select the frame types used by your network. (Ethernet 802.2,
Ethernet 802.3, Ethernet SNAP, and Ethernet II) By default, all
frame types are enabled.
Novell Remote Printer Mode
Novell LevelOne
NetWare LevelOne Printer Server to service the LevelOne Printer
Printer Server for P1
Server's parallel port 1.
Novell LevelOne
NetWare LevelOne Printer Server to service the LevelOne Printer
Page 74
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Server for P2,
P3 & SP
Server's parallel port 2 (P2), parallel port 3 (P3), or Serial port
(SP), if these port exist.
(if exist)
Novell LevelOne Printer Server Mode
NDS Tree Name
Not applicable.
(NetWare NDS mode only)
LevelOne Printer
Server
Not applicable.
(NetWare NDS mode only)
NDS Context
Master File Server
(Bindery mode only)
Name of the LevelOne Printer Server's master file server.
Polling Queue
Interval
Defines how often the LevelOne Printer Server will poll the
queues to be serviced.
Job Notification by
Connection ID
Set to Yes to receive a job notification at only the workstation
where the print job originated, No to receive a job notification at
all workstations that you have logged on.
NetWare Password
The password on the NetWare Server. The LevelOne Printer
Server device needs this password to connect to the NetWare
Server.
Setup for NDPS (NetWare 5)
Overview
·
·
The LevelOne Printer Server must be configured as a valid device on your TCP/IP
network.
To use NDPS (Novell Distributed Printing Services), the Novell server must be running
Novell NetWare 5, and the PCs (clients) must be running IntranetWare Client V2.2. or
later.
The following procedure is designed to enable Public Access Printing under NDPS. Public
Access Printing allows anybody on the network to access the printer.
Creating an NDPS Manager Object
If an NDPS Manager Object already exists, skip this procedure and proceed to Creating an
NDPS Printer Agent.
1. Login to NetWare 5.0 Server as Admin and start the NetWare Administrator program
Nwadmn32.exe.
2. Select the container on NetWare Administrator where you want the NDPS Manager object
to reside. (e.g. TeSupp)
3. Select Create - Object from the menu bar to view the New Object dialog.
4. Select NDPS Manager as the object to create. The Create NDPS Manager Object window
shown below will appear.
Page 75
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 28: Create NDPS Manager Object
5. Type a name in the NDPS Manager Name.(e.g. SerMGR in Figure 1 above)
6. Browse the Resident Server and select where you want the NDPS Manager object to be
assigned. (e.g. TECH_50.TeSupp in figure 1 above)
7. Browse the Database Volume and select where you want the NDPS Manager database to
be assigned. (e.g. TECH_50_SYS.TeSupp in figure 1 above)
8. Click Create. The new NDPS Manager will appear in the main browser window.
·
·
To start the NDPS Manager in future, enter the following command at the console:
LOAD NDPSM
then select the NDPS Manager object.
To start the NDPS Manager whenever you bring up the server, add a command like
the following to your server's AUTOEXEC.NCF file:
LOAD NDPSM SerMGR.TeSupp
The last item is the name of the NDPS Manager object you wish to load.
9. After creating an NDPS Manager, you can create NDPS printers by using NetWare
Administrator, as explained below.
Creating an NDPS Printer Agent
To create Public Access Printers using the NDPS Manager Object in NetWare Administrator,
follow this procedure:
1. Start the NDPS Manager object you will be using to control the Printer Agent.
2. At the Identification page, click the Printer Agent List.
3. Click New to see the Create Printer Agent window, as shown below.
Figure 29: Create Printer Agent
Page 76
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Enter the desired name for the Printer Agent (PA) Name.
5. Normally, the NDPS Manager will be the NDPS Manger object you are using.
6. Select Novell Printer Gateway in the Gateway Type. (see figure2 above)
7. Click OK and then select the available printer.
8. Select Remote (LPR on IP) in the Connection Type.
9. Click Next to see the following Configure Port Handler screen.
Figure 30 Configure Port Handler
10. In the Host address IP field, enter the IP Address previously assigned to the LevelOne
Printer Server device.
11. In the Printer Name field, enter the Logical Port name on the LevelOne Printer Server.
(e.g.: L1)
Note: For LevelOne Printer Servers with one parallel port, the logical ports are named L1,
L2 and L3. For devices with three parallel ports, the logical ports are named L1 to L8.
12. Click Finish, then select appropriate drivers for Windows 3.1, Windows 95/98 and
Windows NT 4.
13. The new Printer Agent will now appear in the Printer Agent List window.
Repeat this procedure for any other ports on the LevelOne Printer Server, or for any other
logical printers you wish to use.
Client PCs can now be configured as described in Chapter 4 - Client Configuration.
Page 77
Download from Www.Somanuals.com. All Manuals Search And Download.
Unix Systems
Your LevelOne Printer Server can be configured using FTP, and it supports the following Unix
printing methods:
·
·
·
·
LPD
FTP
Direct Socket Interface
PSfilter (proprietary printing method)
For full details on using Unix systems with your LevelOne Printer Server, refer to the Unix
manual in the /Manual/Unix directory on the CD-ROM.
Page 78
Download from Www.Somanuals.com. All Manuals Search And Download.
|