|
LevelOne
10/100M 32bit Fast Ethernet
PC card
user’s manual
Version 1.2
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory compliance
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules. This
equipment also complies with CE EN55022 Class B and VCCI V3 Class B
specifications.
These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in
a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
own expense.
Changes or modifications not expressly approved by the parties
responsible for compliance could void the user’s authority to operate the
equipment.
About this manual
This user’s manual describes how to install and operate your LevelOne
10/100Mbps 32bit Fast Ethernet PC Card. Please read this manual before
you install the product.
This manual includes the following topics:
Ø
Ø
Ø
Ø
Product description, features and specifications.
Hardware installation procedure.
Software installation procedure.
Trouble shooting procedures
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
Table of contents
Regulatory compliance...................................................................................... i
About this manual............................................................................................... i
Table of contents................................................................................................ii
CHAPTER 1
Introduction
4
4
Features ..............................................................................................................4
CHAPTER 2
Hardware installation
5
5
What’s in the package.........................................................................................5
Hardware description .........................................................................................5
Inserting the LevelOne 10/100Mbps 32bit Fast Ethernet PC Card...................6
Connecting to a LAN..........................................................................................7
Status LEDs........................................................................................................7
Ejecting the LevelOne 10/100Mbps 32bit Fast Ethernet PC Card ....................9
CHAPTER 3
Driver installation for Win 95/98/2000/ME/NT
11
11
Driver installation for Windows 95..............................................................12
Driver installation for Windows 98..............................................................14
Driver installation for Windows 2000 .........................................................17
Driver installation for Windows ME ............................................................21
Driver installation for Windows NT 4.0.......................................................24
CHAPTER 4
Driver installation for DOS environments
28
28
System Requirements.......................................................................................28
Driver installation...........................................................................................28
Driver installation program...............................................................................28
Quick installation..............................................................................................29
The Install program.........................................................................................30
Using the Install program .................................................................................30
Auto configuration............................................................................................32
Custom configuration .......................................................................................34
Manual installation ........................................................................................36
Enablers ............................................................................................................36
Driver installation...........................................................................................38
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Microsoft Windows for Workgroups 3.11.......................................................38
Netware 3.X/4.X client.....................................................................................39
Microsoft LAN Manager .................................................................................39
Artisoft LANtastic version 6.0 ........................................................................40
CHAPTER 5
Installation for Linux
41
41
Before Installation ............................................................................................41
Install Driver.....................................................................................................42
APPENDIX A
Troubleshooting
45
45
Q&A for Windows environments...................................................................45
Windows 95/98.................................................................................................45
Windows NT 4.0..............................................................................................46
Windows 2000..................................................................................................46
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
Thank you for purchasing the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card. This high-speed LevelOne 10/100Mbps 32bit
Fast Ethernet PC Card complies with the CardBus standard and
uses a female RJ-45 adapter to connect to the network.
The LevelOne 10/100Mbps 32bit Fast Ethernet PC Card is
switchless and software configurable. For convenience and ease of
operation, LAN (RJ-45) connector is built onto the card.
Features
·
Extended PC Card design that integrates RJ-45 connector
onto the PC card
·
·
No moving parts to break and no media coupler to lose
Complies with IEEE 802.3u 100Base-TX and IEEE 802.3
10Base-T
·
·
·
·
·
·
Complies to PCMCIA 1995 PC Card standard
PC Card standard 68-pin 32-bit PCMCIA interface
Support all popular Network Operating Systems
Supports hot swap card insertion and removal
10/100Mbps auto-sensing
Full/half-duplex auto-negotiation for both 10Base-T and
100Base-TX
·
Switchless configuration setting
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware installation
Chapter 2
Hardware installation
This chapter covers inserting your LevelOne 10/100Mbps 32bit
Fast Ethernet PC Card in the notebook’s CardBus slot, and
connecting the card to a network.
What’s in the package
Please ensure that the following items are included in your package.
If any items are missing, contact your dealer.
·
·
LevelOne 10/100Mbps 32bit Fast Ethernet PC Card
CD-ROM diskettes (includes device drivers and this user’s
manual)
·
Quick Installation Guide
Hardware description
The LevelOne 10/100Mbps 32bit Fast Ethernet PC Card is
encased in a stainless compact frame and has a 68-pin connector
for attaching to the notebook’s CardBus slot, and an RJ-45
connector for use with 10BaseT Ethernet or 100BaseTx Fast
Ethernet networks.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
Please take note that the hardkey of a CardBus card is different
from that of the traditional 16-bit PCMCIA card. This mechanism
can protect the 3.3V CardBus card from mis-insertion to 5V 16-bit
PCMCIA slot.
Status LEDs
RJ-45
Hardkey of 5/3.3V Traditional PCMCIA Card (left) and 3.3V CardBus
Card (right)
Inserting the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card
These instructions apply to most notebook computers.
For detailed information on inserting PC cards into your
notebook, consult the notebook user’s manual.
Note!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware installation
Follow the procedure below to install the LevelOne 10/100Mbps
32bit Fast Ethernet PC Card.
1. With the card’s 68-pin connector facing the notebook’s
CardBus slots, slide the card all the way into an empty slot.
Do not force the connection!
2. Connect to a network. (See Connecting to a LAN that
follow.)
Connecting to a LAN
To use the LevelOne 10/100Mbps 32bit Fast Ethernet PC Card’s
Ethernet capability, you can connect to a port on a hub or to an RJ-
45 phone jack with another male-to-male RJ-45 line or connector.
Connecting to a hub
Connecting to an RJ-45 phone jack
7
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
Status LEDs
The following illustration shows the LevelOne 10/100Mbps 32bit
Fast Ethernet PC Card LEDs:
LINK/ACT LED
10/100M LED
RJ-45
The following table describes the meaning of the LEDs:
LED
MEANING
10/100M
Indicates the connection speed. When off, the
connection speed is 10 Mbps. When on, the connection
speed is 100 Mbps.
LINK/ACT
Indicates link status and transmit/receive activity. It is
normally off. When off, indicates that the link is inactive.
When lit, indicates that the link is active. When there is
packet transmit or receive activity, this LED is blinking.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware installation
Ejecting the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card
After you have disconnected the RJ-45 connectors, you can eject
the LevelOne 10/100Mbps 32bit Fast Ethernet PC Card from the
notebook’s PC Card slot.
In Win 95/98/2000/ME operating systems, you do not
have to power down the notebook to remove the card.
The card is hot-swappable—you can remove the card
when the notebook is powered on. However, Microsoft
recommends that you stop the card. Refer to your
Windows 95/98/2000/ME online help for information on
stopping the LevelOne 10/100Mbps 32bit Fast Ethernet
PC Card.
Note!
Most notebooks have an eject lever or button for ejecting PC cards
from the PC slots. Consult your notebook’s user’s manual for
details.
To prevent data loss, do not eject the LevelOne 10/100Mbps
32bit Fast Ethernet PC Card when a data transmission is
taking place. Exit your communications program normally,
stop the card if necessary, and then remove the card.
Warning!
This concludes Chapter 2. The next chapter covers driver
installation for Windows 2000/98/95/NT/ME operating systems.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
NOTES
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Driver installation for
Win 95/98/2000/ME/NT
The following sections cover LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card driver installation in the Windows
2000/98/95/NT/ME operating systems.
Before Installation
To identify the version of Windows 95, you can check the General
system properties. To get the general system properties, double-
click the System icon from the Control Panel.
The version of Windows 95 OSR2 is 4.00.950 B. Make sure the
version of your Windows 95 is correct.
Next, check whether your notebook PCMCIA controller supports
CardBus. You can check it from Device Manager. If the
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
PCMCIA socket is shown to be PCIC or TCIC compatible
Controller, then the notebook cannot support CardBus.
Driver installation for Windows 95
Installation of the LevelOne 10/100Mbps 32bit Fast Ethernet PC
Card is just the same as for any normal Windows 95 Plug & Play
device. Follow the steps below to install the driver in Windows 95.
1. Insert the LevelOne 10/100Mbps 32bit Fast Ethernet PC
Card into an available CardBus slot in your notebook(refer
to page 6 “Inserting the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card”).
2. After Windows 95 detects the card, the Update Device
Driver Wizard window appears:
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
3. Insert the driver disk and click Next to continue the
installation. Windows searches for the driver and the
following screen appears:
4. Click Finishto continue, Windows 95 copies driver files to
the hard disk.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
5. Windows 95 prompts you to restart the system. Click Yes
to complete the installation.
Driver installation for Windows 98
Follow the steps below to install the LevelOne 10/100Mbps 32bit
Fast Ethernet PC Card drivers for Windows 98.
6. Insert the LevelOne 10/100Mbps 32bit Fast Ethernet PC
Card into an available CardBus slot on your notebook (refer
to page 6 “Inserting the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card”).
7. After Windows 98 detects the LevelOne 10/100Mbps 32bit
Fast Ethernet PC Card, the Add New Hardware Wizard
window appears:
8. Click Next to continue the installation. A screen appears
prompting you to select an installation method:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
9. Select Search for the best driver for your device.
(Recommended) and click Next. The following screen
appears:
10. Ensure that the CD-ROM drive box is checked.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
11. Insert the driver disk into your floppy drive and click Next.
The following screen appears:
12. Click Next. Windows 98 copies files to your hard disk drive,
and you see the following screen:
13. Click Finish.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
Windows 98 may need to copy required
system files and will prompt you to input
the path to the files. Follow the
instructions on your screen, then click
OK to continue.
Note!
You should reboot your system to finish the installation.
Driver installation for Windows 2000
Follow the steps below to install the LevelOne 10/100Mbps 32bit
Fast Ethernet PC Card drivers for Windows 2000.
1. Insert the LevelOne 10/100Mbps 32bit Fast Ethernet PC
Card into an available CardBus slot on your notebook (refer
to page 6 “Inserting the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card”).
2. After Windows 2000 detects the LevelOne 10/100Mbps
32bit Fast Ethernet PC Card, the Found New Hardware
Wizard window appears:
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
3. Click Next to continue the installation. A screen appears
prompting you to select an installation method:
4. Select Search for a suitable driver for my device
(recommended) and click Next. The following screen
appears:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
5. Ensure that the Specify a location box is checked and
click Next. The following screen appears:
6. Type “E:\Win2000” where “E” is your floppy drive letter.
Insert the driver disk, and click OK. The following screen
appears:
19
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
7. Click Next to continue. The following screen appears:
8. Click Yes to continue the installation.
9. Windows copies files and the following screen appears:
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
10. Click Finish to complete the installation.
You should reboot the computer to insure a successful installation.
Driver installation for Windows ME
Follow the steps below to install the LevelOne 10/100Mbps 32bit
Fast Ethernet PC Card drivers for Windows ME.
1. Insert the LevelOne 10/100Mbps 32bit Fast Ethernet PC
Card into an available CardBus slot on your notebook (refer
to page 6 “Inserting the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card”).
2. After Windows ME detects the LevelOne 10/100Mbps
32bit Fast Ethernet PC Card, the Add New Hardware
Wizard window appears:
21
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
3. Select Specify the location of the driver (Advanced)
and click Next. The following screen appears:
4. Select Search for the best driver for your device.
(Recommended) and choose Specify a location. Type
"E:\WinME" where "E" is your CD-ROM driver letter.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
Insert the driver disk, and click Next. The following screen
appears:
5. Click Next. Windows ME copies files to your hard disk
drive, and you see the following screen:
6. Click Finish.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
Windows ME may need to copy required
Note!
system files and will prompt you to input
the path to the files. Follow the
instructions on your screen, then click
OK to continue.
You should reboot your system to finish the installation.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
Driver installation for Windows NT 4.0
This installation procedure assumes that you have installed the
network component on your computer.
To check whether the network component has been installed,
double click the Network icon in the Control Panel. If it has not
been installed, refer to the Windows NT 4.0 installation guide for
instructions on installing the component.
Follow the steps below to install the driver.
1. Insert the LevelOne 10/100Mbps 32bit Fast Ethernet PC
Card into an available CardBus slot on your notebook (refer
to page 6 “Inserting the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card”).
2. Log in to NT 4.0 as “Administrator”.
3. Double click the Network icon in the Control Panel, and
select the Adapters tab as shown in the following screen:
25
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
4. Click Add to add a new adapter. The following screen
appears:
5. Click Have Disk. The following screen appears:
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
6. Type “E:\WinNT40” where “E” is your CD-ROM drive
letter. Insert the driver disk, and click OK.
After finding the installation file, the Select OEM Option
window is displayed.
7. Click OK. A screens appears prompting you to input the
IRQ, I/O port address, and connection type:
27
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
8. Select the desired resources and connection type.
You must select resources that are not
being used by another device;
otherwise, you will have a system
conflict error. In case of a system
conflict error, try another setting and
continue.
Note!
9. Click OK to continue. Windows will configure the
LevelOne 10/100Mbps 32bit Fast Ethernet PC Card. You
are returned to the Network window.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Win 95/98/2000/ME/NT
10. Click Close to exit the Network window. Windows NT
4.0 will bind the adapter with the network component and
you will be prompted to restart the system.
When Windows NT is finished binding the adapter to the
network component, you are prompted to restart the system.
11. Click Yes to finish the installation.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Driver installation for DOS environments
This section covers CardBus 10/100Mbps Ethernet Card driver
installation for DOS environment operating systems.
System Requirements
Hardware
Requirements
Notebook equipped with Type II PC Card slot
and CardBus controller (PCMCIA 1995 PC Card
Standard or higher)
Software
Requirements
The Card & Socket service drivers should
comply with PCMCIA 1995 PC Card Standard or
higher
Driver installation
You must install the CardBus 10/100Mbps Ethernet Card drivers
before your computer system can recognize your Ethernet Card.
The following sections cover client driver installation.
Driver installation program
INSTALL is the CardBus 10/100Mbps Ethernet Card driver
installation program. The INSTALL program automatically selects
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver installation for DOS environments
the most suitable option settings, or you can perform a custom
configuration where you individually select each setting.
Quick installation
This section gives a brief overview of the installation process. For
a more detailed description, refer to The Install Program?
1. Card and Socket Services software should be bundled with your
computer; if it is not, contact your dealer. It is recommended
that you use this software when installing your CardBus
10/100Mbps Ethernet Card.
A system with Card and Socket Services installed allows
the CardBus card to automatically configure itself. While
the system is on, available system resources and insertion or
removal of the card will automatically be detected.
2. Run the INSTALL.EXE program found on your driver disk.
The install program guides you through the installation process
and will install the network drivers needed to run the card on
your network operating system.
If you successfully completed the installation, go to step 5.
If installation was unsuccessful, then go to the next step.
3. If you are using Card and Socket Services, select auto-
configuration. The install program will prompt Card and Socket
Services to assign an available hardware resource configuration.
4. If you do not have Card and Socket Services or if your card
does not work with your version of Card and Socket Services,
the enabler program can communicate directly with the
31
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
CardBus controller on your system. However, you must select
hardware resource settings that are not being used by other
devices; otherwise, your PC system may have device conflicts.
5. Insert the LevelOne 10/100Mbps 32bit Fast Ethernet PC Card
into the CardBus socket. Then attach the network cable to the
card.
6. Restart your computer and connect to your network. If you
cannot connect to the network, refer to Appendix A
The Install program
Before you can use your LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card, you need to install and modify some files in your
computer system. You can make these changes manually, or you
can let the INSTALL.EXE program make them for you.
This section explains how you can use the INSTALL.EXE
program to install the enablers and the files needed by the network
operating system.
Using the Install program
To run the INSTALL.EXE program, follow these instructions:
At the DOS prompt type INSTALL and press [Enter]. You see an
opening screen, which welcomes you to the program and asks if
you wish to continue.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver installation for DOS environments
Press [Enter] to continue the installation.
The program prompts you for the directory where you want to
install the driver files. You can choose the default directory name
or enter a new name. Then, press <Enter> to continue with the
installation.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
The next screen asks if you want to do an Auto Configuration or
a Custom Configuration.
Select Auto Configuration if you want to do a quick installation and
use the default configuration settings. If you wish to individually set
any of the settings, then select Custom Configuration.
Auto configuration
If you selected Auto Configuration, the program auto detects
which IRQ and I/O Port the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card can use. After successfully auto-detecting the
configuration, the program shows the following screen:
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver installation for DOS environments
After the configuration process, you are prompted to select the
type of network that you are installing. Select a network operating
system from the list by moving the cursor to your selection and
pressing <Enter>.
After selecting the network operating system, the INSTALL
program will copy and modify files on your boot drive. Your
35
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
CONFIG.SYS file will also be modified to include the Enabler
Driver. You should see the following message if the installation has
been successful:
Custom configuration
To perform a custom installation, you need to select the Custom
Configuration Menu after you begin the INSTALL program.
After selecting the Custom Installation Menu, you see a series of
submenus prompting you to select an IRQ and I/O address.
Interrupt select
The first submenu is the Interrupt submenu. Move the cursor to the
interrupt of your choice and select it by pressing <Enter>.
Interrupts available for your LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card include 9, 10, 11, 12 and 15.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver installation for DOS environments
IO port select
Move the cursor to the desired I/O address and press <Enter>.
Available I/O Ports are D000H, D400H, D800H, E000H, E400H
and E800H.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
Manual installation
In most cases, the INSTALL program can make all system
changes necessary for using your LevelOne 10/100Mbps 32bit
Fast Ethernet PC Card. However, in some cases, you may wish to
make changes manually. This section explains how to manually
make driver and file modifications to enable your card.
Enablers
You can use RTPCI.EXE to enable the CardBus 10/100Mbps
Ethernet Card.
The RTPCI program
The program RTPCI.EXE communicates with the PC Card
controller of your computer. This program is needed only for DOS
environment network operating systems. You may install the
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver installation for DOS environments
Socket and Card Services to your notebook before executing the
driver. If you do not have the Socket and Card Services program,
please contact your notebook vendor.
The Install program can use the following syntax and format:
RTPCI /?[h] /l /r<d> /s<d> /i<dd> /p<xxxx> /m<xxxx>
where
/?
/h
/l
Display this message
Display this message
List PCI config space
/r
IRQ routing [1=PCI, 2=ISA]
Socket number (dec) [0-1]
IRQ line number (dec) [00-15]
I/o base address (hex) [1000-FF80]
Mem base address (hex) [C000-FFC0]
/s
/I
/p
/m
After you executed RTPCI.EXE, you will see a display similar to
the following indicating that the installation was successful:
I/o hole : 1000
Mem hole : CC00
IRQ:-1, I/O: 100h
SOCKET:A
,
MEM: CC00h,
bus: 002, dev: 00, fun: 0, irq: 11
39
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
After you executed RTPCI.EXE, you must run the RTBIOS.COM
to enhance the PCI BIOS.
Driver installation
The following sections cover installation of the client driver for
Windows for Workgroups 3.11, Netware 3X/4X, Microsoft LAN
Manager, and Artisoft LANtastic Version 6.0.
Microsoft Windows for Workgroups 3.11
Follow these instructions to install the Windows for Workgroups
3.11 client for your Ethernet Card:
1. Run INSTALL.EXE, and choose Windows for Workgroups.
2. Run Windows by typing WIN at the DOS prompt.
3. Click the Network icon in the Main Program Group.
4. Click the Network Setup icon from the Network window.
5. Select the Drivers item from the Network Setup dialog box.
6. Select the Add Adapters item in the Option dialog box.
7. Select Unlisted or Updated Network Adapter when the Install
driver field appears.
8. Type the path E:\WFW311(where E: is your floppy drive) and
press <Enter>.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver installation for DOS environments
9. When the CardBus 10/100Mbps Ethernet Card dialog box
appears, select the options step by step.
10. Follow the instructions on the screen.
11. Reboot your computer.
Netware 3.X/4.X client
Follow these instructions to install the Netware 3.X/4.X client for
your Fast Ethernet PC Card:
1. Run the INSTALL program, and select the Netware ODI
Driver.
2. Follow the instructions on the screen to complete the installation.
3. Reboot the computer.
4. When the computer reboots, log on to the network.
Microsoft LAN Manager
Follow these instructions to install the Microsoft LAN Manager
client for your Fast Ethernet PC Card:
1. Run the INSTALL program, and choose LAN Manager.
2. Type lmsetup in the LAN Manager Directory. Press <Enter>.
3. Select Network Drivers in Configuration Press <Enter>.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
4. Select Add New Configs and then press <Enter>.
5. Select Other Driver and press <Enter>.
6. Insert the driver disk into the floppy drive and click OK.
7. Select the Network Adapter Driver, CardBus 10/100Mbps
Ethernet Card, then click OK.
8. Press <Spacebar> to select the desired protocol.
9. Click OK. The message Configuration Complete appears.
10. Click Save, then press <F3> to exit.
Artisoft LANtastic version 6.0
Follow these instructions to install the Artisoft LANtastic Version
6.0 client for your Fast Ethernet PC Card:
1. Run the INSTALL program, and choose LANtastic.
2. Select Artisoft LANtastic, and specify C:\LANTASTI as the
destination directory.
3. When the Select network adapter screen appears, choose
NDIS Support for Network Adapters.
4. When the install program prompts you for the manufacturer's
driver disk in the Enter NDIS driver directory screen, insert the
driver disk.
Follow the instructions on the screen to complete the installation,
then reboot the computer to start LANtastic.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation for LINUX
Chapter 5
Installation for LINUX
This device driver has been fully tested on the following platforms:
Slackware 3.6
Slackware 4.0
Slackware 7.0
Slackware 7.1
Redhat 5.2
Redhat 6.0
Redhat 6.2
The complete file list is as follows:
README
makefile
rtl8139.c
en0100r.o
Before Installation
Before you start rebuilding the driver, you must have PCMCIA binaries
and source installed in your system. PCMCIA module version 3.0.9 or
later are quaranteed to work well with this driver. Latest version of
43
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
have just rebuilt your kernel, you must first rebuild PCMCIA then the
device driver to avoid any inconsistency. When you are rebuilding
PCMCIA modules, be sure you select the following item:
(1) Read from the currently running kernel.
Otherwise, you might encounter some problems with when module
version is set.
Install Driver
1. To login as the "root".
2. To copy the driver code from the floppy diskette, simply do
> mcopy a:Linux/en0100r-v1.0.tgz
> gzip -cd en0100r-v1.0.tgz | tar xvf -
> cd en0100r-v1.0
3. To generate the driver
Modify the PCMCIASRC variable in your makefile to the location of your
PCMCIA source.
Modify the KERN_VER variable in your makefile.
After you finish the modification of variables in your makefile, you can
rebuild the driver by doing
> make
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation for LINUX
4. To install the driver
> make install
5. To configure the LevelOne 10/100Mbps 32bit Fast Ethernet PC
Card
> cd /etc/pcmcia
To add the following text into the "config" file (The mode of
the "config" file must be the "write" mode.)
> vi config
device "FPC-0106TX
class "network" module "cb_enabler", FPC-0106TX"
card " LevelOne 10/100Mbps 32bit Fast Ethernet PC Card "
manfid 0x018a, 0x0106
bind "FPC-0106TX"
To configure the PCMCIA NIC interface
> vi network.opts
6. To reboot the Linux
> shutdown -r now
45
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
NOTES
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Troubleshooting
Q&A for Windows environments
These guidelines give you tips to deal with some problems you may
encounter while using the LevelOne 10/100Mbps 32bit Fast
Ethernet PC Card. If the problems remain unsolved, contact your
dealer for assistance.
Windows 95/98
Problem: Ejecting the card from the CardBus socket hangs or
reboots the computer.
Solution: To prevent this phenomenon from occurring, stop the
card by using the PC Card tool in the Control Panel or the PC
Card icon on the taskbar before you remove the card.
Problem: The card cannot be detected when reinserted.
Cause: This is caused by certain unstable CardBus status lines
when the card is removed and reinserted. The Windows 95/98
drivers may read an incorrect status during this period of signal
instability, and fail to detect the correct status of the card.
Solution: The card can be detected by clicking Refresh in
Device Manager.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
LevelOne Fast Ethernet PC Card user’s manual
Windows NT 4.0
Question: Does the driver support "hot-swap" on NT 4.0?
Answer: Windows NT 4.0 don't support hot swapping. If you want
to remove the card, shut down the computer and remove it.
Windows 2000
Question: What is the Microsoft digital signature?
Answer: Drivers that pass Microsoft Windows 2000 certification
receive a digital signature file from Microsoft. The LevelOne
10/100Mbps 32bit Fast Ethernet PC Card does not have such a
digital signature, however it is fully compatible with Windows
2000.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
|