®
COMPACT DISC PLAYER
MW/FM DUAL CASSETTE RECORDER
WITH REMOTE CONTROL
MODEL CD-511
OPERATING INSTRUCTIONS
INCLUDES FULL FEATURE REMOTE CONTROL
MULTI-COLOURED FLUORESCENT DISPLAY
PLAYS MUSIC COMPACT DISCS
SING ALONG WITH KARAOKE
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT PLAY
FUNCTION
•
•
•
•
•
RECEIVES MW/FM STEREO BROADCASTS
ROTARY BASS & TREBLE CONTROLS
RECORDS FROM CD, TAPE OR RADIO
2 WAY POWER - AC/DC
•
•
•
•
REQUIRES 8 X LR20 (SIZE “ D ”) BATTERIES (NO INCLUDED)
•
PLEASE READ CAREFULLY BEFORE USE
Imported and distributed by Worldwide Retail Sourcing (UK) Limited
491 Holloway Road London N19 4DD
email address: [email protected]
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY SAFETY INSTRUCTIONS
CAUTION:
TO REDUCE THE RISK OF FIRE, PERSONAL INJURY OR DAMAGE TO THE
PLAYER, PLEASE READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries stated in the operating instructions
booklet (Batteries are not included with the player. Please buy the correct
batteries).
2. Do not dispose of the batteries by burning them as they may explode.
Check with local regulations for any special instructions on the disposal of
batteries.
3. Do not open or dismantle batteries. Do not recharge non-rechargeable
batteries.
4. Be careful when handling batteries in order not to short-circuit them with
conducting materials such as rings, bracelets and keys. The battery or
conductor may overheat and cause burns.
5. Do not attempt to extend the life of batteries for use with this product by
heating them.
6. All batteries should be replaced at the same time. Mixing old and new
batteries could increase internal cell pressure and damage the batteries.
7. When inserting batteries into this product, the correct polarity (
direction must be observed.
or
) or
8. Remove the batteries from the product if it is not to be used for a long period
of time (several weeks or more).
9. Remove old or flat batteries as soon as possible as they are more likely to
leak in the product.
10. Do not store the product in high temperature areas.
11. Opening or removing covers may expose you to dangerous voltages or
other risks. Incorrect reassembly may cause electric shocks when the
appliance is subsequently used.
12. If any liquid leaks from the batteries, wipe it up immediately. Do not let any
of the liquid come into contact with your skin and discard the leaking
batteries.
13. Do not mix batteries (OLD and NEW or CARBON and ALKALINE etc.).
14. The use of rechargeable batteries is not recommended for this player
because their voltage and life is lower than those of standard batteries.
15. Installation of batteries should only be done by an adult.
PLEASE SAVE THESE INSTRUCTIONS
2
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING A POWER SOURCE
AC power or batteries may be used as a power source.
AC SOCKET
1. Connecting the AC power
TIP
cord
Replace the batteries
Insert one end of the supplied AC power cord (located
in the polyfoam) into the socket located at the back
of the player, and the other end into a wall outlet.
•
when the display dims or
when the player stops
operating. Replace all
batteries with new ones.
2. Using battery power
Insert 8 X LR20 (size “D”) batteries (not included)
into the battery compartment.
Before
replacing
batteries, make sure
there is no CD in the
player and remember to
check the Battery Safety
Instructions on Page 2.
To use the player on batteries, disconnect the AC
power cord from the player.
U P P E R
If the CD does not play
•
L O W E R
on batteries, this means
the batteries are almost
used up. But the radio
may continue to play on
these weak batteries
because it uses less
power than the CD
player.
VFD DISPLAY
The VFD display only lights up when using AC
power.
3
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE SPEAKERS
1.Position one of the speakers to the right
of the main unit.
P
R
O
G.
2.Align the tracks (rails) on the speaker with
the main unit as shown in FIG. 1.
FIG.1
3.When the speaker tracks (rails) are lined
up, push the speaker into the tracks (rails)
on the main unit as shown in FIG. 2.
P
ROG
.
4.Repeat steps 1 to 3 above for the left side.
FIG.2
5.Carefully unwind the speaker wire from behind each speaker and insert the
right plug into Speaker Jack R and the left plug into Speaker Jack L (as shown
in FIG. 3). Wrap the remaining wire behind each speaker.
LOCK TAB
FIG.3
NOTE: This player can be used with the speakers either attached to the main unit
or standing alone so long as both speaker plugs are plugged into the
jacks.
To detach the speakers, press the lock tab and push the speakers out of
the tracks (rails).
4
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
The CD PLAYER can be operated with the REMOTE CONTROL provided (includes
the following controls: POWER ON/OFF, MUTE, VOLUME, CD REPEAT and PLAY).
NOTE: When you use the REMOTE CONTROL to operate the CD PLAYER,
make sure the POWER button on the main unit is turned on.
Otherwise, the REMOTE CONTROL will not work.
1. POWER ON/OFF
2. MUTE
3. REPEAT - ONE & ALL SONGS
9
1
4. PROGRAMME
5. VOLUME UP/DOWN
8
6. SKIP/SEARCH BACKWARD
7. SKIP/SEARCH FORWARD
8. STOP
2
3
7
9. PLAY/PAUSE
NOTE: When you press the POWER
ON/OFF button to switch the
player off, the VFD display will
go out and the STANDBY
indicator on the main unit will
come on.
4
6
5
Slide the battery cover off to remove the batteries. Insert 2 X LR4 (size “AAA”)
batteries (not included) correctly so that the + and - polarities match the polarity
indicators inside the battery compartment.
NOTE:
About half a year of normal operation can be expected when using alkaline
•
batteries.
When the batteries are worn out, the remote control will stop working.
Replace both batteries with new ones.
•
When the remote control is not to be used for a long time (2 months or
more), the batteries should be removed to avoid possible damage that may
be caused by battery leakage.
•
Avoid keeping the remote control in extremely hot or humid locations.
The remote control will operate at a distance of between about 0.2m (8
inches) and 6m (20 feet) from the remote sensor.
•
•
5
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A CD
3
5
1
2
6
PROG.
Connect the supplied AC power cord or batteries (see page 3).
Press the POWER button for the
VFD display and AUDIO LEVEL to
come on.
1
2
Slide the FUNCTION switch to the
CD position. Two dashes, “--” , will
appear on the VFD display.
Open the CD DOOR by pressing the
bottom righthand corner of the CD
door marked OPEN/CLOSE and
place the CD in the CD
compartment. The label side of the
CD should face upward.
3
O
C
P
E
N
L
O
S
E
CLOSE
Close the CD DOOR by pushing it
down. The display will show the total
number of tracks (songs) on that
CD.
4
5
6
Press the CD PLAY button. The
player will play all the songs (tracks)
once in order.
To change the sound effect, adjust
the BASS and TREBLE knobs as
desired.
TIP: “
” WILL APPEAR IN THE DISPLAY IF THERE IS NO DISC IN THE CD
COMPARTMENT OR IF THE DISC IS UPSIDE DOWN.
6
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME CONTROL
TIP
The AUDIO LEVEL
will light up when the
power is on and
the pointer will
PROG.
indicate
any
changes in audio
levels.
TIP
When CD play is
paused, “ ” will
flash and the CD
will stop playing.
FUNCTION SWITCH
To
Press or Adjust
Adjust the volume
VOLUME control
STOP
Stop playback
To resume play,
press the PAUSE
PLAY/PAUSE
” will flash when a CD is in
pause mode. Press again to
resume play.
button again, “
”
“
will stop flashing
and the CD will play.
Pause playback
Go to the next track
TIP
FORWARD
BACKWARD
If the player or the
table it is sitting on
is knocked while a
CD is playing, the
CD will stop or skip
for a few seconds.
This is normal for
this type of player.
Go back to the previous
track
or
Press and hold down while
playing until you find the
point.
Locate a point in a song
Press the bottom righthand
corner of the CD DOOR
TIP
This set has an
electronic volume
Remove the CD
marked
OPEN/CLOSE
(press STOP first).
control.
The
volume can be
raised or lowered
by pressing the
VOLUME UP or
DOWN button.
Press the POWER button
and the display will go off.
Turn off the player
To turn off the sound
instantly
Press the MUTE button on
the REMOTE CONTROL.
7
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
REPEAT PLAY
PLAYING CD SONGS (TRACKS) REPEATEDLY
CD tracks can be played over and over again in either normal or programmed play
mode (see page 9). (NOTE: To use this feature, you need to operate the set with
the REMOTE CONTROL, because there is no REPEAT button on the main unit.)
POWER
BUTTON
REPEAT
FUNCTION
SWITCH
1. Press the POWER button for the display to light up.
2. Set the FUNCTION switch to the CD position.
3. Select the track by pressing
or
, and then press
.
4. Press the CD REPEAT button on the REMOTE CONTROL.
To repeat
Display shows
Press
a single track (song)
Press the REPEAT
button once
“REP” will flash.
REP
Press the REPEAT
button twice
“REP” will stay
on continuously
all the tracks (all songs)
programmed tracks
Press the REPEAT
R E P
“REP” will stay
on continuously
button
twice
while
programmed tracks are
being played
To cancel Repeat Play
Press the REPEAT button until “REP” goes off.
8
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMED CD PLAY
SELECTING YOUR OWN MUSIC PLAYING ORDER
PROGRAMME
Up to 19 tracks may be programmed to play
in whatever order you wish.
NOTE: Programming is only done during
STOP mode.
During STOP mode, press the
1
PROGRAMME button. “
” and
“PRG.” will flash in the display.
Press
buttons,
the
SKIP/SEARCH
2
3
,
or
until the
desired track shows in the
display.
Press the PROGRAMME button.
“
” and “PRG.” will flash in the
display.
Repeat steps 2 and 3 until all the
desired tracks are programmed.
4
5
Press the PLAY button to start
programmed play. “
” , “PRG.”
and the track number being
played will show in the display.
To change the current programme
Simply create a new programme by following the programing procedure.
To cancel Programmed Play
Press the STOP button twice and “PRG.” will disappear from the display.
9
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
LISTENING TO THE RADIO
3
1
4
2
3
6
PROG
.
Connect the supplied AC power cord or batteries (see page 3).
Press the POWER button for the VFD
display and the AUDIO LEVEL to
come on.
1
Set the FUNCTION switch to the
RADIO position.
2
3
Set the BAND switch to the proper
band position (MW or FM), and the
FM MODE switch to STEREO or
MW
FM
MONO.
Tune into the station of your choice
using the TUNING control. Adjust for
the clearest sound.
4
“FM ST.” will appear in the VFD
display when receiving FM Stereo
broadcasts.
5
6
To change the tone, adjust the
BASS and TREBLE controls as
desired.
10
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME
FM MODE
FUNCTION
PROG.
TIP
To
Press or Set
If an FM broadcast is
•
noisy, move the FM
MODE switch from
STEREO to MONO.
VOLUME control (UP or
DOWN).
Adjust the volume
Set the FUNCTION switch
to the TAPE position or
press the POWER button.
Turn off the Radio
This player has an
•
electronic
volume
control. The volume
can be raised or
lowered by pressing
the VOLUME UP or
DOWN button.
To improve broadcast reception
Change position of the antenna for FM or FM Stereo.
Move the player itself for MW.
PROG.
PROG.
11
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A TAPE
1
2
PROG.
4
3
Connect the supplied AC power cord or batteries (see page 3).
Press the POWER
button for the VFD
display to come on.
1
2
3
FU LL
REEL
EM PTY
REEL
A
Set the FUNCTION
switch to the TAPE
position.
Press the STOP/EJECT
STOP/EJECT
INSERT THIS WAY
button (DECK
A
or
DECK B) to open the
tape compartment and
insert a recorded tape.
Close the door.
PLAY
Press the PLAY button.
The player will come on
and start playing the
tape.
4
5
When the player comes
to the end of one side of
the tape, it will stop. To
listen to the other side
of the tape, turn the tape
over, insert and press
PLAY.
AUTO STOP
12
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
RELAY PLAY
2
1
PROG.
5
4
3
Connect the supplied AC power cord or batteries (see page 3).
To play tapes in DECK A and then DECK B, follow the steps below:
Press the POWER button for the VFD
display and AUDIO LEVEL to come on.
1
Set the FUNCTION switch to the TAPE
position.
2
Press the cassette PLAY button on
DECK A for the tape in DECK A to play.
PLAY
3
Press the cassette PAUSE button on
DECK B.
PAUSE
PLAY
4
Press the cassette PLAY button on
DECK B. When DECK A finishes playing,
DECK B will automatically start playing.
5
6
When the player reaches the end of
the tape in DECK B, it will stop.
13
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR ADDITIONAL
CASSETTE TAPE OPERATIONS
VOLUME
CONTROL
PROG.
PAUSE
PLAY
PAUSE
STOP/EJECT
PLAY
FAST F.&REWIND
STOP/EJECT
RECORD
FAST F.&REWIND
To
Press or Adjust
Press the VOLUME button
(UP or DOWN)
Adjust the volume
Stop playback
STOP/EJECT button
Fast forward or rewind
Pause playback
FAST FORWARD button or
REWIND button
PAUSE button
Press again to resume play
STOP/EJECT button
Eject the cassette
To enjoy music without
Insert your headphone plug
into the HEADPHONE jack (at
the front of the player).
disturbing
others
(headphones are not
included)
PROG.
Make sure none of the cassette
buttons are down (on) and the
POWER button is off.
To turn the power off
14
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING ONTO A TAPE
1
PROG.
3
MICROPHONE JACK 4
2
Connect the supplied AC power cord or batteries (see page 3).
Press the POWER button for the VFD display and AUDIO
LEVEL to come on.
1
2
Press the STOP/EJECT button (DECK
STOP/EJECT
B) to open the tape compartment and
insert a blank tape. Select the source
(MW, FM, CD, or microphone) you wish
OK
NO
to record from.
To record from the CD player, set the FUNCTION switch to
the CD position, insert a CD and follow the steps for playing
a CD (see page 6).
To record from the radio, set the FUNCTION switch to the
RADIO position, and tune into the desired station (see page
10).
To record from the microphone, set the FUNCTION switch to
the TAPE position, and plug the microphone (not included)
into the MICROPHONE JACK. Speak into the microphone.
To record from DECK A, set the FUNCTION switch to the
TAPE position and follow the steps for playing a TAPE (see
page 12).
3
OR
OR
THEN
RECORD
4
Press the RECORD button to start recording. (The PLAY
button will automatically be depressed.)
PLAY
REWIND
To listen to what you have recorded, set the FUNCTION
switch to the TAPE position, press REWIND and then
PLAY.
5
15
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
PROG.
TIP
DOUBLE SPEED SWITCH
PAUSE
• For best recording
effect, use AC power
instead of batteries.
STOP/EJECT
• To erase a recording,
simply start a new
recording, and the
old one will auto-
matically be erased.
Press or Set
To
Stop recording
STOP/EJECT button
Pause recording
PAUSE button
Press the button again to
resume recording.
• See page 20 for
notes on cassettes.
Adjust recording
speed when copying
tapes
DUBBING SPEED
switch from NORMAL to
HIGH speed.
Press the STOP/EJECT
button and the POWER
button. The VFD display
will go off.
Turn off the power
16
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
SING ALONG WITH KARAOKE FUNCTION
VOLUME
PROG.
MIC
VOLUME
MICROPHONE JACK
2
Connect the supplied AC power cord or batteries (see page 3).
Insert the microphone plug into the microphone
jack. To avoid howling from the microphone, lower
the volume level first.
1
2
NOTE: Microphone is not included. You can
purchase one at the shop where you
purchased your player.
To sing along with the CD player, set the FUNCTION
switch to the CD position, insert a KARAOKE CD
disc and follow the steps for playing a CD (see
page 6).
To sing along with a tape, set the FUNCTION switch
to the TAPE position, insert a KARAOKE TAPE
into Deck A or B, and follow the steps for playing a
TAPE (see page 12).
3
4
Press the CD PLAY/PAUSE button on the CD
player or the PLAY button on Deck A or B.
PLAY
Adjust the volume controls (both the VOLUME
control on the player and the MICROPHONE
VOLUME control) to achieve the best effect.
17
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR ADDITIONAL
OPERATIONS
PROG.
VOLUME
CONTROL
MIC VOLUME
BASS
TREBLE
To
Press or Adjust
Adjust the MIC volume
MIC. VOLUME
Adjust the CD or TAPE
volume
VOLUME control
Adjust the sound effect
for low or high tones.
BASS or TREBLE
control.
TIP: If any squealing or howling (feedback) occurs during KARAOKE
use, move the microphone away from the speakers or turn down
the volume.
18
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
Safety
Power Sources
The laser beam used in the CD player
For battery operation, use 8 X LR20
•
•
section could damage your eyes so
you should never attempt to take the
cabinet apart. Refer servicing to
qualified personnel only.
(size “D”) batteries (not included). We
recommend alkaline batteries for
longer life.
When the batteries will not be used
•
If any solid object or liquid gets into
for several weeks or more, they should
be removed to avoid damage that
could be caused by battery leakage
or corrosion.
•
the player, unplug it, and have it
checked by qualified personnel before
operating it again.
Location
Operation
Do not leave the player near a heat
•
If the player is moved directly from a
cold to a warm location or is placed
in a very damp room, moisture may
condense on the lens in the CD player
section. Should this occur, the player
will not operate properly. In this case,
remove the CD and wait about an hour
for the moisture to evaporate. If the
player has not been used for a long
time, put it in playback mode to warm
up for a few minutes before inserting
a CD.
•
source in direct sunlight or where it
might be exposed to excessive dust
or mechanical shocks.
Do not place the player on a sloping
or unstable surface.
•
Do not place anything within one inch
•
of the back of the cabinet. The
ventilation holes must not be covered
for the player to operate properly and
to prolong the life of its components.
If the player is left in a car parked in
the sun, be sure to put it somewhere
in the car where it will not be in direct
sunlight.
This CD player is designed to be
played on a stable, vibration-free
surface. If it is knocked while a CD is
playing, the CD will stop or skip for a
few seconds. This is normal for this
type of player.
•
•
Powerful magnets are used in the
•
speakers so personal credit cards
using magnetic coding and spring-
wound watches should be kept away
from the player to prevent possible
damage from the magnets.
19
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS (continued)
CDs
Cassettes
Break off the cassette tab from Side
Before playing, clean the CD with a
•
•
A or B to prevent accidental recording.
cleaning cloth. Wipe the CD from the
centre out.
Side A
Do not use solvents such as benzene,
•
Tab for side A
Tab for side B
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
Do not expose CDs to direct sunlight
To record on a tape with its tab broken
off, cover the respective tab hole for
Side A or B with adhesive tape.
•
•
or heat sources such as hot air ducts,
or leave them in a car parked in direct
sunlight as the temperature inside the
car could get extremely hot and cause
damage to the CDs.
Use of a cassette with more than 90
minutes, such as C-120 (120
minutes), is not recommended. The
extreme thinness of this tape may
damage this set.
•
Do not attach paper or stickers to CDs
or scratch them.
•
•
After playing, CDs should be stored in
their cases. If there is a scratch, dirt
or fingerprints on the CD, tracking
errors or skipping may occur.
To reduce the chance of tapes
jamming or tangling, check that there
is no tape slack visible through the
window in the centre of the cassette.
Any tape slack should be taken up
with a pencil before inserting the
cassette into the player.
•
20
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cleaning the Lens
Storage Cassette
Tapes
If the lens is dirty, skipping may occur
while the CD is playing. Clean with a
commercially available lens cleaner and
blower.
1. Never place tapes near a magnetic
field such as a TV, or speaker.
Magnetic fields may reduce tape
sensitivity or even erase recording.
2. Do not store tapes for any length of
time in hot, damp or dusty locations.
Cleaning the Tape Heads
Wipe the heads, the pinch roller and
the capstan with a cleaning swab slightly
moistened with cleaning fluid or alcohol
after every 10 hours of operation for
optimum playback and recording quality.
After cleaning, wait until the areas
cleaned are completely dry before
inserting a tape.
Cleaning the Cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzene.
COTTON SWAB
CAPSTAN
PINCH ROLLER
ERASE HEAD
RECORD/PLAY BACK HEAD
NOTE: In order to see and clean the
head(s), you may have to
press PLAY first.
21
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Problem
Remedy
Connect the AC power cord securely to a wall outlet.
Make sure the batteries are inserted correctly and
are not worn out.
•
The power is not on.
•
•
Make sure the FUNCTION switch is in the correct
position.
Adjust the volume.
Unplug the headphones when listening
through the speakers.
There is no sound.
•
•
You may be using battery power. The VFD display
will only light up when AC power is used.
•
•
VFD display does not light up.
“
” appears in the display even
Insert the CD with the label side up.
when a CD is in place.
Make sure that the CD compartment is closed.
Clean the CD.
Remove the CD and leave the CD DOOR open for
about an hour to get rid of moisture condensation.
Make sure the FUNCTION switch is in the CD position.
•
•
•
CD does not play.
•
Clean the CD or replace it if it is badly damaged.
Place the player in a location free from vibrations.
Check that the batteries are not worn out.
•
•
•
The sound drops out.
CD does not play while radio may
continue to play.
It is normal since the radio uses less power than
the CD player.
•
Replace all the batteries with new ones if
they are low, move the player close to a
window for better MW reception or rotate it
•
Sound is weak or sound quality is
poor.
for better FM reception.
Make sure the safety tab on the cassette
is in place (see page 20).
Make sure the FUNCTION switch is in the
•
•
The RECORD button does not
function/The tape does not play.
TAPE position.
Clean the erasing head (see page 21).
Replace all the batteries with new ones if they are
low.
The tape does not erase
completely.
•
•
Make sure the tape is inserted correctly.
Make sure the safety tab on the cassette is in place.
•
•
The tape does not record.
Clean the heads, pinch roller and capstan
(see page 21).
Sound is weak or sound quality is
poor.
•
The tape has reached the end of one side. Remove,
turn over and re-insert.
•
Cassette PLAY button pops up.
Tape jamming or tangling
Use only better quality tapes.
•
•
•
Do not use a cassette with more than 90 minutes.
Make sure there are no loose layers of tape visible
before inserting the cassette.
22
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
General Description
Power source:
AC 240V, 50Hz 20Watts
DC 8 X LR20 (size “D”) batteries (not included) for
player
DC 2 X LR4 (size “AAA”) batteries (not included) for
Remote Control
(Alkaline batteries are recommended)
50 - 125mm 4 ohm woofers
50 - 75mm 4 ohm tweeters with crossover
5.0W/channel
Speakers (2 ways):
Output power:
Dimensions (approx.):
MAIN UNIT
265MM
Depth: 220MM
Height: 260MM
Weight: 2.0KG
SPEAKER
172MM
195MM
315MM
1.3KG
Width:
CD Section
Type of disc played:
Laser wavelength:
Tracking method:
Any normal CD used in portable players
760 - 800 NM
3 - spot error detection
3.86 mm lens
Frequency response: 50Hz - 15kHz +1/-2 dB
NOTE: This CD player will only play NORMAL music CDs (or CD-R CDs).
It will not play CDRW encoded discs.
Tape Recorder Section
Frequency response: Standard normal bias cassette tapes
70Hz - 10kHz
Radio Section
Tuning range:
FM: 88 - 108 MHz
MW: 530 - 1600 kHz
LENOXX reserves the right to make design and specification changes for
product improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL IS PUT UNDER
THE PLAYER WHEN IT IS PLACED ON SURFACE WITH A NATURAL OR LACQUER
FINISH.
23
IB-CD511(TA)-SW-E-091002
Download from Www.Somanuals.com. All Manuals Search And Download.
|