®
COMPACT DISC PLAYER
AM/FM STEREO CASSETTE RECORDER
MODEL CD-102
OPERATING INSTRUCTIONS
PLAYS ALL MUSIC COMPACT DISCS
•
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT
•
RECEIVES AM/FM STEREO BROADCASTS
•
RECORDS FROM CD, RADIO, OR BUILT-IN MICROPHONE
•
FM STEREO AND POWER LED INDICATORS
•
2 WAY POWER - AC/DC
•
REQUIRES 6 SIZE “C” BATTERIES (not included)
•
PLEASE READ CAREFULLY BEFORE USE
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-102SY040300NLv.1 E
SAFETY INSTRUCTIONS
14. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
15. Damage Requiring Service - The appliance should be serviced by qualified service
personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure damaged.
16. Servicing- The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
17. Power lines - An outdoor antenna should be located away from power lines.
18. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the
antenna system is grounded so as to provide some protection against voltage surges and
built up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70 provides
information with respect to proper grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and requirements for the
grounding electrode. See Figure.
EXAMPLE OF ANTENNA GROUNDING AS PER
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
It is the intent of Lenoxx that this product be used in full compliance with the
copyright laws of the United States and that prior permission be obtained from
copyright owners whenever recording songs from the RADIO or CD’s.
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated
on the bottom of the set.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY SAFETY INSTRUCTIONS
CAUTION:
TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR
SET, READ ANDFOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery electrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING in this
instruction manual. If you can’t resolve the problem, or if the product is damaged, refer to the
LENOXX WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when
the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch your skin,
and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING THE POWER SOURCES
You can use the AC power or batteries as a power source.
To a wall outlet
AC SOCKET
NOTE: One blade of plug
and outlet is wider.
Battery compartment
1. Connecting the AC power
cord
TIP
Insert one end of the supplied AC power cord
(located in the battery compartment) into the socket
located at the rear of the player, and the other end
to the wall outlet.
If the plug of the AC power
cord does not match your
outlet, do not force it.
Reverse it and try again.
The plugs are polarized
and only fits one way into
the wall outlet and back of
the set.
2. Using the player on batteries
Insert 6 size “C” batteries (not supplied) into the
battery compartment.
To use the player on batteries, disconnect the AC
power cord from the player.
TIP
Replace the batteries
when the POWER lamp
dims or when the player
stops operating. Replace
all the batteries with new
ones. Before you replace
the batteries, be sure to
take out the CD from the
player and remember to
check the Battery Safety
Instructions on Page 3.
c
c
c
c
c
c
UP PE R
LO W E R
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A CD
3
1
2
4
Connect the supplied AC power cord or batteries (see page 4).
Slide the FUNCTION
switch to CD position
(power on), the POWER
1
2
POWER
lamp
lamp will be on.
FUNC TIO
N
Lift the right corner of the
CD DOOR to open it and
place the CD in the CD
compartment. The label
side of the CD should face
upward.
Close the CD DOOR by
pushing it down. The
display will show the total
tracks on that CD.
3
4
Press the CD PLAY
button.
The PLAY/
/
PLAY
PA USE
PAUSE lamp will be
steady on, the player
plays all the tracks once.
Track PLAY/PAUSE
number lamp
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME CONTROL
(at the left side of the set)
OPEN THE CD DOOR
FUNCTION SWITCH
BY LIFTING HERE
TIP
When CD play is
paused, the PLAY/
PAUSE lamp will
flash and no music
will play.
To
Press or Adjust
Adjust the volume
Stop playback
VOLUME control
To resume play,
press the PAUSE
button again, the
PLAY/PAUSE lamp
will stop flashing
and music will play.
The PLAY/PAUSE lamp will
flash during pause. Press
again to resume play after
pause.
Pause playback
Go to the next track
FORWARDS
BACKWARDS
TIP
If you bump the set
during CD play, the
music will stop or
Go back to the previous
track
skip for
a
few
or
seconds. This is
normal for this type
of player.
Press and hold down while
playing until you find the
point.
Locate a point in a song
Lift the CD DOOR (press
STOP first)
Remove the CD
Slide the FUNCTION switch
to TAPE position
Turn off the power
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LISTENING TO THE RADIO
2
3
1
4
Connect the supplied AC power cord or batteries (see page 4).
Slide the FUNCTION switch to
RADIO position, the POWER
lamp will be on.
1
2
FUNC TIO
N
Slide the BAND switch to the
proper band position (AM, FM, or
FM STEREO) that you want.
Tune into the station you prefer
using the TUNING control (at the
right side of the set). Adjust for
the clearest sound.
T
3
4
U
N
I
N
G
This indicator will light up when
receiving FM Stereo broadcasts.
FM STEREO
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
2
1
TIP
To
Slide or Adjust
If the FM broadcast is
•
Adjust the volume
VOLUME control (at the
left side of the set)
noisy, slide the BAND
switch from FM Stereo
to FM position (MONO).
Slide the FUNCTION
switch to TAPE position
Turn off the Radio
Next time you want to
listen to the radio, just
slide the FUNCTION
switch to RADIO. The
player automatically
starts playing the
•
To improve broadcast reception
Change position of the antenna for FM or FM Stereo.
Move the set itself for AM.
previously
station.
tuned
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A TAPE
3
2
1
Connect the supplied AC power cord or batteries (see page 4).
TAPE PLAY DIRECTION
Slide the FUNCTION
switch to TAPE position.
1
A
FUNC TIO
N
EMPTY
REEL
FULL
REEL
Press the STOP/EJECT
button to open the tape
compartment and insert
a recorded tape. Close
the door.
2
INSERT TAPE THIS WAY
FULL REEL ON RIGHT
STOP/EJECT
Press the PLAY button.
The player turns on and
starts playing.
3
4
PLAY
OK
NO
When the set finishes
playing this side of the
tape, the set will stop. To
hear the other side of the
tape, flip the tape over,
then insert and press
PLAY.
AUTO STOP
OK
NO
9
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR ADDITIONAL
OPERATIONS
VOLUME
CONTROL
MICROPHONE
PAUSE
STOP/EJECT
PLAY
FAST F.&REWIND
HEADPHONE
JACK
To
Press or Adjust
VOLUME control (at the left side
of the set)
Adjust the volume
STOP/EJECT button
Stop playback
Fast forward or rewind
the tape
FAST FORWARD button or
REWIND button
Pause playback
PAUSE button
Press again to resume play after
pause.
Eject the cassette
STOP/EJECT button
Insert your headphone plug into
the HEADPHONE Jack
To enjoy the music
without disturbing others
Make sure cassette buttons are
all up (stop) and FUNCTION switch
is in the center position (power
off).
To shut power off
10
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING ON A TAPE
1
3
Connect the supplied AC power cord or batteries (see page 4).
Press the STOP/EJECT button to
TAPE PLAY DIRECTION
open the tape compartment and
1
2
insert a blank tape. Select the
program source (AM, FM, CD, or,
built-in microphone) you want to
A
STOP/EJECT
record.
EMPTY
REEL
FULL
REEL
To record from the CD player, insert
a CD and follow the steps to play a
CD (see page 5).
IN SERT TAPE THIS WAY
FULL REEL ON RIGHT
To record from a radio, slide the
FUNCTION switch to RADIO, and
tune into the station you want (see
page 7).
FUNC TIO
FUNC TIO
N
N
To record from the built-in
microphone, leave the FUNCTION
switch at the TAPE position, and
speak in front of the set.
Press the RECORD button to start
recording. (The PLAY button is
depressed automatically.)
3
4
OK
NO
RECORD
To hear what you recorded, slide
the FUNCTION switch to TAPE
position, then press REWIND and
PLAY.
OK
NO
REWIND
PLAY
11
Download from Www.Somanuals.com. All Manuals Search And Download.
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
TIP
FUNCTION
SWITCH
• For best recording
effect, use the AC
power instead of
batteries.
PAUSE STOP/EJECT
To
Press or Adjust
• To
erase
a
recording, just start
a new recording,
and the old one is
a u t o m a t i c a l l y
replaced.
STOP/EJECT button
Stop recording
PAUSE button
Press the button again
to resume recording.
Pause recording
Turn off the power
Press the STOP/EJECT
button and slide the
FUNCTION switch to TAPE
position.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
PLAYING CD TRACKS REPEATEDLY
(REPEAT PLAY)
You can play CD tracks over and over in normal or program play modes (see page
14).
PROGRAM REPEAT
FUNCTION
LAMP LAMP
SWITCH
1. Slide the FUNCTION switch to CD position.
2. Select the track by pressing
or
, and then press
.
3. Press the CD REPEAT button.
To repeat
Repeat Lamp
Press
a single track (song)
Press the REPEAT button once
Flashing
all the tracks (all songs)
programmed tracks
Press the REPEAT button twice
Steady on
During programmed play, press
the REPEAT button twice
Steady on
(the PROGRAM
lamp also on)
To cancel Repeat Play
Press the REPEAT button until the REPEAT lamp goes off.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING YOUR OWN MUSIC PLAYING ORDER
(Programmed Play)
PROGRAM LAMP
PGM
You can make a program of up to 16
tracks in the order you want them to
be played.
NOTE: Programming is only done during
stop mode.
1. Slide the FUNCTION switch to CD position.
2. Press the PROGRAM button. The letters “Pr” and
PROGRAM.
the PROGRAM lamp will flash.
3. Press
or
to select the tracks you want to
program in the order you want.
4. Press the PROGRAM button to confirm. The letters
“Pr” and the PROGRAM lamp will flash.
5. Repeat steps 3 and 4. You can program up to 16
tracks.
/
SKIP SEARC H
6. Press
to start program play. The PROGRAM
PROGRAM
lamp will be steady on.
To check the order of tracks before play
Press the PROGRAM button, the programmed track number appears in the display
automatically.
PROGRAM
To change the current program
Just create a new program following the programing procedure.
PROGRAM.
To cancel Program Play
Press the STOP button twice and the PROGRAM lamp goes off.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
On Safety
On Power Sources
For battery operation, use 6 size C
As the laser beam used in the CD
•
•
batteries. We recommend alkaline
batteries for longer life.
player section may be harmful to the
eyes, do not attempt to disassemble
the cabinet.
qualified personnel only.
Refer servicing to
When the batteries will not be used
•
for a few weeks or more, remove them
to avoid damage that can be caused
by battery leakage or corrosion.
Should any solid object or liquid fall
into the player, unplug the player, and
have it checked by qualified personnel
before operating it any further.
•
On Operation
On Placement
If the player is brought directly from a
•
Do not leave the player in a location
•
cold to a warm location, or is placed
in a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
player will not operate properly. In
this case, remove the CD and wait
about an hour for the moisture to
evaporate. If the player has not been
used for a long time, set it in the
playback mode to warm it up for a few
minutes before inserting a cassette.
near a heat source, or in a place
subject to direct sunlight, excessive
dust or mechanical shock.
Do not place the player on an inclined
or unstable place.
•
Do not place anything within 1 inch of
•
the back of the cabinet. The
ventilation holes must not be covered
for the player to operate properly and
prolong the life of its components.
This CD player is designed to be
•
If the player is left in a car parked in
•
played on
a
stable no vibration
the sun, be sure to choose a location
in the car where the player will not be
subjected to the direct rays of the
sun.
position. If you bump the set during
CD play, the music will stop or skip for
a few seconds. This is normal for this
type of player.
Since a strong magnet is used for the
•
If you have any questions or problems
concerning your player, please contact
our customer service department at
1-800-315-5885.
(Monday - Thursday 09:00 AM - 05:00 PM,
Friday 09:00 AM - 01:00 PM EST)
speakers, keep personal credit cards
using magnetic coding or springwound
watches away from the player to
prevent possible damage from the
magnets.
•
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS (continued)
Notes on CDs
Notes on Cassettes
Before playing, clean the CD with a
Break off the cassette tab from side A
•
•
cleaning cloth. Wipe the CD from the
center out.
or B to prevent accidental recording.
Side A
Do not use solvents such as benzene,
•
Tab for side A
Tab for side B
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
Do not expose the CD to direct
To record on a tape with its tab broken
off, cover the respective tab hole for
side A or B with adhesive tape.
•
•
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car.
The use of a cassette with more than
•
90 minutes of play time is not
recommended except for long
continuous recording or playback.
Do not stick paper or stickers on the
CD, nor scratch the CD.
•
To reduce the chances of tape
•
After playing, store the CD in its case.
jamming or tangling, you should check
that there are no loose layers of tape
visible through the cassette center
window. If any, tighten these loose
layers of tape using a pencil before
inserting the cassette into the set.
•
If there is a scratch, dirt or fingerprints
on the CD, it may cause a tracking
error or skipping.
Download from Www.Somanuals.com16. All Manuals Search And Download.
MAINTENANCE
Cleaning the Lens
Notes for Storing
Cassette Tapes
If the lens becomes dirty, it may cause a
skipping of sound during CD operation.
Clean with a commercially available lens
cleaner and blower.
1. Do not put a tape near a magnetic
field, such as a TV, or speaker.
Magnetic fields may reduce the tape
sensitivity or even erase the
recording.
2. Do not store tape for any length of
time in a hot, moist or dusty place.
Cleaning the Tape Heads
Wipe the heads, the pinch roller and
the capstan with a cleaning swab slightly
moistened with cleaning fluid or alcohol
after every 10 hours of operation for
optimum playback and recording quality.
After cleaning, insert a tape when the
areas cleaned are completely dry.
Cleaning the Cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder, or solvent, such as alcohol or
benzene.
RECORD/PLAY BACK HEAD
PINCH ROLLER
ERASE HEAD
CAPSTAN
COTTON SWAB
NOTE: In order to see and clean the
head, you may have to press
PLAY first.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Problem
Remedy
Connect the AC power cord to a wall
outlet securely.
•
The power is not on.
Make sure the batteries are inserted
correctly and they are fresh.
•
Make sure the FUNCTION switch is at the
right position as you want.
•
There is no sound.
Adjust the volume.
Unplug the headphones when listening
through speakers.
•
•
Insert the CD with the label side up.
“
” appears in the display
•
•
even when a CD is in place.
Make sure that the CD compartment is
closed.
Place the CD with the label side up.
Clean the CD.
Take out the CD and leave the CD DOOR
open for about an hour to dry moisture
condensation.
•
•
•
CD does not play.
Make sure the FUNCTION switch is at CD
position.
•
•
•
Clean the CD, or replace it if the CD is
badly damaged.
Place the player in a location free from
vibration.
The sound drops out.
Check if your batteries are fresh.
•
•
Replace all the batteries with new ones if
they are weak, or bring the set near a
window, or rotate the set.
The sound is weak or has
poor quality.
Make sure the safety tab on the cassette is
in place.
Make sure the FUNCTION switch is at TAPE
position.
•
•
The RECORD button does
not function/The tape does
not play.
Clean the erasing head (see page 17).
Replace all the batteries with new ones if
they are weak.
•
•
The tape does not erase
completely.
Make sure the tape is inserted properly.
Make sure the safety tab of the cassette
is in place.
•
•
The tape does not record.
Clean the heads, pinch roller and capstan
(see page 17).
The sound is weak/The
sound quality is poor.
•
The tape has reached its end. Remove it,
flip to the other side and re-insert.
Cassette PLAY button pops
up.
•
Download from Www.Somanuals.com. All Manuals Search And Download.
18
SPECIFICATION
General Description
Power source:
AC 120V, 60Hz 12Watts
DC 12V (6 size “C” batteries)
(Alkaline batteries are recommended)
1
Speakers:
2 - 3 / ” 8 ohm
2
Output power:
Dimensions:
1.5W/channel
1
Width: 14 / ”
Depth: 8”
2
3
Height: 6 / ”
4
Weight: 5LBs (without batteries)
CD Section
Any normal CD used in portable players
760 - 800 NM
Plays disc type:
Laser wavelength:
Tracking method:
3 - spot error detection
3.86 mm lens
Frequency response: 80Hz - 15kHz
Tape Recorder Section
Frequency response: Standard normal bias cassette tape,
70 - 10kHz
Radio Section
Frequency range:
FM: 88 - 108 MHz
AM: 530 - 1700 kHz
LENOXX reserves the right to make design and specification changes for
product improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED
UNDER THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR
LACQUER FINISH.
For customer service
Dial 1-800-315-5885
(MONDAY - THURSDAY 09:00 AM - 5:00 PM, FRIDAY 09:00 AM - 1:00 PM EST)
or Visit Our Website: http://www.lenoxx.com
© 2000 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
19
CD-102SY032000NLv.1 E
|