ThinkServer RD330
User Guide
Machine Types: 3072, 3073, 3074, 4302, 4304, and 4305
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Setting the system date and time
46
48
49
50
50
Using passwords .
Selecting a startup device
Introduction .
1
2
Configuring the TPM function .
0 .
51
51
51
53
Exiting the Setup Utility program .
Updating or recovering the BIOS.
7
7
Features .
Specifications .
Software .
11
11
11
12
12
12
12
12
12
12
13
program
program
53
54
ThinkServer EasyStartup .
ThinkServer EasyUpdate Firmware Updater
55
56
56
Configuring RAID.
About RAID .
Configuring RAID using the ThinkServer
Configuring the ThinkServer RAID 300
58
58
Configuring the advanced SATA/SAS hardware
Configuring the Ethernet controllers
Updating the firmware.
63
64
64
64
Machine type, model, and serial number
label .
13
14
17
19
20
22
25
25
27
program .
65
Rear view of the server
Hot-swap hard disk drive status LEDs
Guidelines
67
67
68
69
69
69
71
71
Mini-SAS to mini-SAS signal cable
Handling static-sensitive devices
connections .
29
31
34
39
Removing the server cover .
Installing, removing, or replacing hardware
Removing and reinstalling the rack handles
Removing and reinstalling the cooling
shroud .
73
75
81
85
43
43
Installing or removing a memory module.
Installing or removing the RAID card
Installing or removing the ThinkServer RAID
500 Upgrade Key for Advanced RAID .
Installing or removing the ThinkServer RAID
700 Battery .
45
45
89
93
program
45
© Copyright Lenovo 2012
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing or removing the ThinkServer RAID
problems .
156
157
300 Upgrade Key for Advanced RAID .
Installing or removing the ThinkServer
96
100
103
Management Module Premium
Platform Module .
Installing or replacing a hot-swap redundant
Information resources .
159
159
159
159
160
160
160
161
161
power supply
Installing or replacing a heat sink.
106
110
113
Installing or replacing a hot-swap hard disk
Help and service .
drive .
122
126
Before you call .
Using other services
Installing or replacing the optical drive
Replacing the hot-swap hard disk drive
backplane.
132
Replacing the Intelligent Diagnostics
Module .
137
139
141
143
145
147
Replacing a system fan
164
164
164
164
165
Replacing the riser card assembly 1
Replacing the system board battery
Polyvinyl Chloride (PVC) cable and cord notice .
Recycling information .
Completing the parts replacement .
Reinstalling the server cover and reconnecting
cables .
Updating the server configuration
147
151
perchlorate .
165
166
2002/96/EC .
166
170
170
170
153
153
153
154
Electronic emission notices.
Viewing the status and diagnostic LEDs.
Viewing the system event log .
Statement.
170
172
ThinkServer EasyStartup program
problems .
154
154
155
ii ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety information
Note: Before using the product, be sure to read and understand the multilingual safety instructions on the
documentation DVD that comes with the product.
Antes de usar o produto, leia e entenda as instruções de segurança multilíngues no DVD de documentação
que o acompanha.
Преди да използвате този продукт, задължително прочетете и вникнете в многоезичните инструкции
за безопасност в DVD диска с документация, който се предоставя с продукта.
Prije upotrebe ovog proizvoda obavezno pročitajte višejezične sigurnosne upute koje se nalaze na DVD-u s
dokumentacijom koji dobivate uz proizvod.
Před použitím produktu je třeba si přečíst a porozumět bezpečnostním pokynům uvedeným na disku DVD s
dokumentací, který je dodáván s produktem.
Før du bruger produktet, skal du sørge for at læse og forstå de sikkerhedsforskrifter, der findes på flere
sprog, på den dokumentations-dvd, der følger med produktet.
Lue tuotteen mukana toimitetulla DVD-tietolevyllä olevat monikieliset turvaohjeet ennen tämän tuotteen
käyttöä.
Avant d'utiliser le produit, veillez à bien lire et comprendre les instructions de sécurité multilingues figurant
sur le DVD de documentation fourni avec le produit.
Πριν χρησιμοποιήσετε το προϊόν, βεβαιωθείτε ότι έχετε διαβάσει και κατανοήσει τις οδηγίες ασφάλειας, οι
οποίες είναι διαθέσιμες σε διάφορες γλώσσες στο DVD τεκμηρίωσης που συνοδεύει το προϊόν.
Vor Verwendung des Produkts sollten Sie unbedingt die mehrsprachigen Sicherheitsanweisungen auf der
Dokumentations-DVD lesen, die im Lieferumfang des Produkts enthalten ist.
A termék használata előtt mindenképpen olvassa el és értelmezze a termékhez kapott dokumentációs DVD
lemezen található, több nyelven elolvasható biztonsági előírásokat.
Prima di utilizzare il prodotto, accertarsi di leggere e comprendere le informazioni sulla sicurezza multilingue
disponibili sul DVD di documentazione fornito con il prodotto.
製品をご使用になる前に、製品に付属の Documentation DVD に収録されているマルチリンガルの「安
全に正しくご使用いただくために」を読んで理解してください。
제품을 사용하기 전에 제품과 함께 제공되는 문서 DVD의 다국어 안전 지침을 주의 깊게 읽어보십시오.
Voordat u het product gebruikt, moet u ervoor zorgen dat u de meertalige veiligheidsinstructies op de
documentatie-dvd van het product hebt gelezen en begrijpt.
© Copyright Lenovo 2012
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Przed skorzystaniem z produktu należy zapoznać się z wielojęzycznymi instrukcjami bezpieczeństwa
znajdującymi się na płycie DVD z dokumentacją dostarczoną wraz z produktem.
Antes de utilizar o produto, leia atentamente as instruções de segurança multilingues que constam no
DVD de documentação fornecido com o produto.
Înainte de a utiliza produsul, asiguraţi-vă că aţi citit şi înţeles instrucţiunile de siguranţă în mai multe limbi de
pe DVD-ul cu documentaţie care însoţeşte produsul.
Før du bruker produktet, må du lese og forstå den flerspråklige sikkerhetsinformasjonen på DVDen med
dokumentasjon som følger med produktet.
Прежде чем использовать этот продукт, внимательно ознакомьтесь с инструкциями по технике
безопасности на разных языках, которые можно найти на DVD-диске с документацией в комплекте с
продуктом.
在使用本产品之前,请务必先阅读和了解产品附带的文档 DVD 中的多语言安全说明。
Pre nego to upotrebite proizvod obavezno paljivo proitajte i prouite viejeziko uputstvo za bezbednost na
dokumentacionom DVD-u koji ste dobili uz proizvod.
Pred pouvanm produktu si pretajte viacjazyn bezpenostn pokyny na disku DVD s dokumentciou dodanom s
produktom.
Preden začnete uporabljati izdelek, je pomembno, da preberete in razumete večjezična varnostna navodila
na DVD-ju z dokumentacijo, ki ste ga prejeli skupaj z izdelkom.
Antes de utilizar el producto, asegúrese de leer y comprender las instrucciones de seguridad multilingües del
DVD de documentación que se proporciona con el producto.
Var noga med att läsa säkerhetsinstruktionerna på dokumentations-DVD-skivan som följer med produkten
innan du börjar använda produkten.
使用本產品之前,請務必閱讀並瞭解產品隨附的文件 DVD 上的多國語言版本安全資訊。
Bu ürünü kullanmadan önce, ürünle birlikte gönderilen belge DVD'si üzerindeki çok dil içeren güvenlik
yönergelerini okuyup anladýðýnýzdan emin olun.
Перед використанням цього продукту уважно ознайомтеся з інструкціями з техніки безпеки на різних
мовах, що можна знайти на DVD-диску з документацією в комплекті з продуктом.
Important: The caution and danger statements in this document are labeled with numbers. Each number
identifies an English-language caution or danger statement that refers to translated versions of the caution
or danger statement in the Safety Information document. For example, if a danger statement is labeled
“Statement 1,” translations for this danger statement are in the Safety Information document under
“Statement 1.”
Ensure that you read and understand all caution and danger statements in this document before you perform
the procedures. Read and understand any additional safety information that is included with the server or
optional device before you install, remove, or replace the device.
iv ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 1
DANGER
Electrical current from power, telephone, and communication cables is hazardous.
To avoid a shock hazard:
• Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this
product during an electrical storm.
• Connect all power cords to a properly wired and grounded electrical outlet.
• Connect to properly wired outlets any equipment that will be attached to this product.
• When possible, use one hand only to connect or disconnect signal cables.
• Never turn on any equipment when there is evidence of fire, water, or structural damage.
• Disconnect the attached power cords, telecommunications systems, networks, and modems before you
open the device covers, unless instructed otherwise in the installation and configuration procedures.
• Connect and disconnect cables as described in the following table when installing, moving, or opening
covers on this product or attached devices.
To connect:
To disconnect:
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlets.
5. Turn devices ON.
2. First, remove power cords from outlets.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Statement 2
DANGER
Danger of explosion if battery is incorrectly replaced.
When replacing the lithium coin cell battery, use only the same or an equivalent type that is
recommended by the manufacturer. The battery contains lithium and can explode if not properly
used, handled, or disposed of.
Do not:
• Throw or immerse into water
• Heat to more than 100°C (212°F)
• Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
© Copyright Lenovo 2012
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are
installed, note the following:
• Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
• Use of controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam.
Statement 4
≥ 18 kg (39.7 lb)
< 32 kg (70.5 lb)
≥ 32 kg (70.5 lb)
< 55 kg (121.2 lb)
≥ 55 kg (121.2 lb)
< 100 kg (220.5 lb)
CAUTION:
Use safe practices when lifting.
Statement 5
CAUTION:
The power control button on the device and the power switch on the power supply do not turn off
the electrical current supplied to the device. The device also might have more than one power
cord. To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.
vi ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 6
CAUTION:
If you install a strain-relief bracket option over the end of the power cord that is connected to the
device, you must connect the other end of the power cord to a power source that is easily accessible
in case it needs to be disconnected.
Statement 7
CAUTION:
If the device has doors, ensure that you remove or secure the doors before moving or lifting the
device to protect against personal injury. The doors will not support the weight of the device.
Statement 8
CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.
Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components. If you suspect a problem with
one of these parts, contact a service technician.
Statement 9
CAUTION:
Disconnect the hot-swap fan cables before removing the fan from the device to protect against
personal injury.
Statement 10
CAUTION:
The following label indicates a sharp-edge hazard.
© Copyright Lenovo 2012
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 11
CAUTION:
The following label indicates a potential heat hazard.
Statement 12
DANGER
Overloading a branch circuit is a potential fire hazard and a shock hazard under certain conditions. To
avoid these hazards, ensure that your system electrical requirements do not exceed branch current ratings
at the installation site.
Statement 13
CAUTION:
Ensure that the rack is secured properly to avoid tipping when the server unit is extended on the rails.
Statement 14
CAUTION:
Some accessory or option board outputs exceed Class 2 or limited power source limits. You
must install the appropriate interconnecting cabling in accordance with your local electrical code
requirements.
Statement 15
CAUTION:
The power-control button on the device may put the device in standby mode instead of turning off
the device. In addition, the device might have multiple connections to dc power. To remove all
electrical current from the device, ensure that all connections to dc power are disconnected at
the dc power input terminals.
viii ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 16
CAUTION:
To reduce the risk of electric shock or energy hazards:
• This equipment must be installed by trained service personnel in a restricted-access location, as
defined by your local electrical code and the latest edition of IEC 60950.
• Connect the equipment to a reliably earthed safety extra low voltage (SELV) source. An SELV
source is a secondary circuit that is designed so that normal and single fault conditions do not
cause the voltages to exceed a safe level (60 V direct current).
• The branch circuit overcurrent protection must be rated in accordance with local electrical code
requirements.
• Use 1.3 mm2 or 16 American Wire Gauge (AWG) copper conductor only, not exceeding 3 meters
in length.
• Torque the wiring-terminal screws to 1.4 newton-meters or 12 inch-pounds.
• Provide a readily available, approved and rated disconnect device in the field wiring.
Statement 17
CAUTION:
This product contains a Class 1M laser. Do not view directly with optical instruments.
Statement 18
CAUTION:
Do not place any object on top of rack-mounted products.
Statement 19
CAUTION:
Hazardous moving parts. Keep fingers and other body parts away.
© Copyright Lenovo 2012
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Statement 20
CAUTION:
A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace the
battery only with the Lenovo-approved part. Recycle or discard the battery as instructed by local
regulations.
x
ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. General information
This chapter provides some general information about your product.
This chapter contains the following items:
•
•
Introduction
This user guide for your Lenovo® ThinkServer® product contains information about the server features,
specifications, component locations, configuration instructions, hardware replacement procedures, and
basic troubleshooting and diagnostics.
Your server comes with a documentation DVD that contains various server documents to help you use and
maintain the server. Meanwhile, your server comes with a ThinkServer EasyStartup DVD that provides a
convenient solution for configuring the server and installing an operating system.
The Lenovo Limited Warranty (LLW) contains the warranty terms that apply to the product you purchased from
Lenovo. Read the LLW on the documentation DVD that comes with your server. A printable generic version
of the latest LLW also is available in more than 30 languages at http://www.lenovo.com/warranty/llw_01. If
you cannot obtain the LLW through the documentation DVD or Lenovo Web site, contact your local Lenovo
office or reseller to obtain a printed version of the LLW, free of charge.
For warranty service, consult the worldwide Lenovo Support telephone list. Telephone numbers are subject
to change without notice. The most up-to-date telephone list for Lenovo Support is always available on the
Web site at http://www.lenovo.com/support/phone. If the telephone number for your country or region is not
listed, contact your Lenovo reseller or Lenovo marketing representative.
To obtain the most up-to-date information about the server, go to:
Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and
download documentation or device drivers and updates. To access the Lenovo Support Web site, go to:
© Copyright Lenovo 2012
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Record information about your server in the following table. You will need the information if you ever need
to have your server serviced.
For where to find the product information label on the chassis, see “Machine type, model, and serial number
______________________________________________
______________________________________________
______________________________________________
______________________________________________
Product name
Machine type and model (MT-M)
Serial number (S/N)
Date of purchase
You can register your server with Lenovo by following the instructions at:
When you register your server, information is entered into a database, which enables Lenovo to contact
you in case of a recall or other severe problem. After you register your server with Lenovo, you will receive
quicker service when you call Lenovo for help. In addition, some locations offer extended privileges and
services to registered users.
Server documentation
This topic provides general descriptions of the various documentation for your server and instructions on
how to obtain all the documentation.
Printed documents
The following documents are printed out and contained in your server package.
• Read Me First
This is a multilingual document you should read first. This document guides you to read the complete
warranty, support, and safety information on the documentation DVD that comes with your server before
using the product. This document also provides information about how to find the most up-to-date
information on the Lenovo Support Web site.
• Important Notices
This document includes safety and legal notices that you should read and understand before using
the server.
• Rack Installation Instructions
This document provides instructions on how to install your server into a standard rack cabinet by using
the rail kit shipped with the server.
Note: This document is available in five languages. A printed English version is included in your server
package. A PDF version of French, German, Italian, and Spanish are provided on the documentation DVD
that comes with the server.
2
ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Documentation DVD
The documentation DVD, which comes with your server, contains various documents for your server in
Portable Document Format (PDF) and HyperText Markup Language (HTML). The documentation DVD is not
bootable. To view the documents on the DVD, you will need a computer with a Web browser and the Adobe
Reader program, which is available for download at:
To start the documentation DVD, insert the DVD into the optical drive. The DVD is AutoPlay enabled and
starts automatically in most Microsoft® Windows® environments. If the DVD fails to start or if you are using a
Linux® operating system, open the launch.htm file located in the root directory of the DVD.
Note: Lenovo maintains pages on the World Wide Web, where you can get the latest technical information
and download documentation or device drivers and updates. Some information in the documents on the
documentation DVD might change without notice after the first release of the DVD. You can always obtain all
the most up-to-date documentation for your server from the Lenovo Web site at:
The following documents are on the documentation DVD that comes with your server:
• Safety Information
This is a multilingual document that includes all the safety statements for your product in more than 30
languages. Be sure to read and understand all the safety statements before using the product.
• Warranty and Support Information
This document includes the Lenovo warranty statement, Customer Replaceable Units (CRUs) information,
and information about how to contact Lenovo Support.
• Lenovo License Agreement
This document includes the terms and conditions of the Lenovo License Agreement.
• User Guide
This document provides detailed information to help you get familiar with your server and help you use,
configure, and maintain your server.
• Rack Installation Instructions
This document provides instructions on how to install your server into a standard rack cabinet by using
the rail kit shipped with the server.
• ThinkServer Management Module User Guide
This document provides information about server remote management. This document is in English only.
You might find this document on the documentation DVD that comes with your server. If not, download it
from the Lenovo Web site at:
Note: To obtain advanced remote management functions, install a ThinkServer Management Module
Chapter 1. General information
Download from Www.Somanuals.com. All Manuals Search And Download.
3
• MegaRAID SAS Software User Guide
This document provides information about Redundant Array of Independent Disks (RAID) and how to
use the utility programs to configure, monitor, and maintain your server RAID and related devices. This
document is in English only.
Note: Refer to this document for hardware RAID information if you have a required RAID card installed in
the server. See “Installing or removing the RAID card” on page 85. For information about the ThinkServer
RAID 300 (also known as the onboard SAS software RAID), see “Configuring the ThinkServer RAID
Document only for trained service personnel
The following document is intended only for trained service personnel of Lenovo.
Hardware Maintenance Manual
This document provides information about component locations, replacement procedures for major Field
Replaceable Units (FRUs), and troubleshooting and diagnostics. This document is updated frequently, and
the most up-to-date version is always available in English on the Lenovo Web site at:
4
ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Server setup road map
This chapter provides a general road map to guide you through setting up your server.
The server setup procedure varies depending on the configuration of the server when it was delivered. In
some cases, the server is fully configured and you just need to connect the server to the network and an
ac power source, and then you can turn on the server. In other cases, the server needs to have hardware
features installed, requires hardware and firmware configuration, and requires an operating system to
be installed.
The general procedure for setting up your server is:
2. Install any required hardware or server option. See the related topics in Chapter 6 “Installing, removing,
3. Install your server into a standard rack cabinet by using the rail kit shipped with the server. See Rack
Installation Instructions that comes with your server.
4. Connect the Ethernet cable and power cord(s) to the server. See “Rear view of the server” on page
20 to locate the connectors.
6. Review the Unified Extensible Firmware Interface (UEFI) settings and customize as needed. See “Using
8. Install any additional drivers needed for added features. Refer to the instructions that come with the
hardware option.
9. Configure Ethernet settings in the operating system by referring to the operating system help. This step
is not required if the operating system was installed using the ThinkServer EasyStartup program.
11. Install other applications. Refer to the documentation that comes with the applications that you want to
install.
© Copyright Lenovo 2012
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Product overview
This chapter provides information about the server package, features, specifications, software programs,
and component locations.
This chapter contains the following items:
•
•
•
•
•
Server package
The server package includes the server, a rail kit, power cord(s), printed documentation, a documentation
DVD, and software media.
Note: Depending on the model, your server might look slightly different from the illustration in this topic.
CPU
Mem
PSU
Figure 1. Server package
1 Server
2 Material box, including power cord(s), printed documentation, a documentation DVD, and software media
3 Rail kit
Features
This topic provides general information about the server features for a variety of models. Depending on your
specific model, some features might vary or not be available. For information about your specific model, use
© Copyright Lenovo 2012
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Microprocessor
One or two Intel® Xeon® quad-core, hexa-core, or octa-core microprocessors (internal cache size varies
by model)
For a list of the ThinkServer microprocessor options, go to:
Memory
Your server has 12 memory slots. For more information, see “Memory module installation rules” on page 75.
Power supply
One or two 550-watt hot-swap redundant power supplies (Universal input and compliant with 80 PLUS Gold)
System fans
You server comes with six system fans to provide proper system cooling and airflow.
Internal drives
Internal drives are devices that your server uses to read and store data. The internal drives supported
by your server vary by model.
• Hard disk drive
– Up to four 3.5-inch hot-swap Serial Advanced Technology Attachment (SATA) or Serial Attached SCSI
(SAS) hard disk drives (SCSI is the acronym for Small Computer System Interface)
– Up to six 2.5-inch hot-swap SAS hard disk drives or SATA solid-state drives
Note: The term “2.5-inch hot-swap hard disk drives” or “2.5-inch hard disk drives” hereinafter refers to all
the supported types of 2.5-inch hard disk drives, including the solid-state drives.
• Optical drive
– One slim SATA optical drive in some models
For the location information about the internal drives or drive bays, see “Server components” on page 22.
Expansion slots
• Two riser card assembly slots on the system board
• One PCI Express card slot on the riser card assembly 1
• One PCI Express card slot on the riser card assembly 2
Input/Output (I/O) features
• One or two Video Graphics Array (VGA) DB-15 connectors
• One serial connector on the rear panel
• Six USB 2.0 connectors (two on the front panel and four on the rear panel)
• Three RJ-45 Ethernet connectors on the rear panel (Ethernet connector 0 is for system management)
For the location information about the connectors, refer to the related topics in “Locations” on page 13.
8
ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Video subsystem
An integrated graphics controller in the ThinkServer Management Module (TMM), which also is known
as the Baseboard Management Controller (BMC) chip, on the system board to support VGA connectors
for connecting video devices
Ethernet connectivity
Three RJ-45 Ethernet connectors on the rear panel with 10 megabits per second (Mbps), 100 Mbps, or
1000 Mbps network connectivity.
• Onboard Intel 82574L Gigabit Ethernet controller for dedicated or shared local area network (LAN)
management interface (Ethernet connector 0 is for system management)
• Onboard Intel Gigabit Dual Port Ethernet controller for Ethernet connector 1 and Ethernet connector 2
Reliability, availability, and serviceability
Reliability, availability, and serviceability (hereinafter referred to as RAS) are three important server design
features. The RAS features help you to ensure the integrity of the data stored on the server, the availability of
the server when you need it, and the ease with which you can diagnose and correct problems.
Your server has the following RAS features:
• Security features
– Administrator password and user password to help protect unauthorized access to the server (see
– ThinkServer Trusted Platform Module (TPM), which is a security chip, to help enhance server security
Note: The TPM is only available in some models.
– Remote monitoring or control by an administrator to provide protection or help
– Hot-swap redundant power supplies to help avoid significant interruption to the operation of the
system when a power supply fails
• Basic system management features
– Ability to store the power-on self-test (POST) hardware test results
– BIOS Setup Utility program
The BIOS Setup Utility program helps you view the server information and configure the server in the
– TMM (also known as BMC) and Intelligent Platform Management Interface (IPMI) 2.0
The system board platform management subsystem is based on the integrated TMM features. The
TMM is a management chip that is integrated on the system board of your server. With the TMM chip,
no matter what condition the server operating system is in and no matter if the server is on or off, as long
as the server is connected to network and an ac power source, the interaction with the TMM-controlled
servers can be achieved through system network. The user can obtain the server hardware health
information and system event log (SEL), and is able to conduct the operations including turning on or
off the server, restarting the server, locking the power switch on the front panel, and so on. This part of
server management is independent of the operating system and is called out-of-band management.
The system board platform management subsystem consists of the integrated TMM, communication
buses, sensors, the BIOS, and server management firmware. It is responsible for error reporting,
system power control, thermal monitoring, system fan control, and other management features. The
TMM provides system management and monitoring features based on the IPMI 2.0 specification. IPMI
Chapter 3. Product overview
Download from Www.Somanuals.com. All Manuals Search And Download.
9
helps lower the overall costs of server management. You can find more information about IPMI 2.0
from the Web site of Intel. The TMM also supports some non-IPMI features, such as the Dynamic Host
Configuration Protocol (DHCP) and the Platform Environment Control Interface (PECI), to provide
more system management functions.
For more information, refer to the ThinkServer Management Module User Guide, which is available for
download at:
– Hot-swap feature
Your server supports hot-swap hard disk drives and hot-swap redundant power supplies. With the
hot-swap feature, you can install, remove, or replace a hot-swap device without turning off the server.
– Preboot Execution Environment (PXE)
The Intel PXE technology enables you to boot your computers, load an operating system, or deploy
executable images from a remote server by using a network interface. The operation can be done
independently of local data storage devices (such as hard disk drives) or operating systems.
– Redundant Array of Independent Disks (RAID)
Your server supports ThinkServer RAID 300 and advanced SATA/SAS hardware RAID configurations if
you have a required RAID card installed. For detailed information, see “Configuring RAID” on page 56.
– Status light-emitting diodes (LEDs) and diagnostic LEDs
For more information about the LEDs for your server, refer to the related topics in “Locations” on
page 13.
– Software programs
– Wake on LAN
When the Wake on LAN feature is enabled on a computer that is connected to a LAN, a network
administrator can remotely turn on or wake up the computer from a management console using remote
network management software. Besides, many other functions, such as data transfer and software
updates, can be performed remotely without remote attendance and can be done after normal working
hours and on weekends to save time and increase productivity.
• Advanced system management features
The advanced system management features are only available when the TMM detects the presence of a
ThinkServer Management Module Premium (TMM Premium), which also is known as integrated keyboard,
video, and mouse (iKVM) key. The TMM Premium is a remote management module. You can purchase
a TMM Premium from Lenovo and install it on the TMM Premium connector (also known as iKVM
connector) on the system board of your server to enable the iKVM function and activate the advanced
system management features.
For more information about advanced system management, refer to the ThinkServer Management Module
User Guide, which is available for download at:
10 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
This topic lists the physical specifications for your server.
Dimensions
Width: 436 mm ( 17.17 inches) without handles; 482.4 mm ( 18.99 inches) with handles
Height: 43.6 mm (1.72 inches)
Depth: 720.6 mm (28.37 inches) without handles; 734 mm (28.90 inches) with handles
Weight
The product weight varies depending on different system configurations.
Range of product weight without package: 12 kg (26.46 lb) to 17 kg (37.48 lb)
Range of product weight with package : 15 kg (33.07 lb) to 24 kg ( 52.91 lb)
Environment
• Air temperature:
Operating: 10°C to 35°C (50°F to 95°F)
Storage: -40°C to 70°C (-40°F to 158°F) in original shipping package
• Altitude: 0 to 3048 m (0 to 10 000 ft) in an unpressurized environment
• Humidity:
Operating: 8% to 80% (non-condensing)
Storage without package: 8% to 80% (non-condensing)
Storage with package: 8% to 90% (non-condensing)
Electrical input
• Universal input:
– Low range:
Minimum: 100 V ac
Maximum: 127 V ac
Input frequency range: 50 to 60 Hz
– High range:
Minimum: 200 V ac
Maximum: 240 V ac
Input frequency range: 50 to 60 Hz
Software
This topic provides information about the software programs that you can use to set up, use, and maintain
the server.
ThinkServer EasyStartup
The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported
Microsoft Windows and Linux operating systems and device drivers on your server. This program is provided
with your server on a self-starting (bootable) ThinkServer EasyStartup DVD. The user guide for the program
also is on the DVD and can be accessed directly from the program interface. For detailed information, see
Chapter 3. Product overview 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ThinkServer EasyUpdate Firmware Updater
The ThinkServer EasyUpdate Firmware Updater program (hereinafter referred to as the Firmware Updater
program) enables you to maintain your server firmware up-to-date and helps you avoid unnecessary server
outages. The Firmware Updater program is provided on the Lenovo Support Web site. For more information
Lenovo ThinkServer EasyManage
The Lenovo ThinkServer EasyManage program enables enterprise users to remotely control and monitor
multiple Lenovo servers within a LAN.
BIOS and TMM update utilities
The BIOS and TMM (also known as BMC) firmware keeps updating after the shipment of the server.
Lenovo maintains pages on the Support Web site and provides the BIOS and TMM update utilities with
instructions for download to help you update the BIOS and TMM firmware if needed. For more information,
RAID configuration utilities
With some RAID configuration utilities, your server supports ThinkServer RAID 300 and advanced SATA/SAS
on page 56.
Remote management software
The integrated TMM provides basic remote management features for the server. The add-on TMM Premium
option provides advanced remote management features for the server.
For detailed information about the remote management software and server remote management, refer to
the ThinkServer Management Module User Guide, which is available for download at:
Lenovo Rack Planner
Racks and servers are usually deployed on a large scale. When deploying the equipment, equipment
managers need a lot of reference parameters to calculate power consumption and electric current values
under different configurations. The Lenovo Rack Planner program provides data maintenance, power
consumption and electric current calculations, and reports to help equipment managers significantly
increase efficiency in deploying the equipment and conveniently manage the equipment.
instructions on the Web page.
For detailed information about using the Lenovo Rack Planner program, refer to the help system for the
program.
ThinkServer Smart Grid Technology
The ThinkServer Smart Grid Technology program helps administrators to monitor and manage server
performance, especially the power consumption for groups of servers equipped with the Intel Intelligent
Power Node Manager technology.
12 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Lenovo provides a trial version of the ThinkServer Smart Grid Technology program with a free 90-day
subscription. After 90 days, you must renew the license to continue using the program. You can purchase
the license from Lenovo to activate the ThinkServer Smart Grid Technology program and expand the
management capability of the program when the free trial ends.
follow the instructions on the Web page.
For detailed information about using the ThinkServer Smart Grid Technology program, refer to the help
system for the program.
Locations
This topic provides information to help you locate your server components.
Machine type, model, and serial number label
This topic helps you locate the label that contains the machine type, model, and serial number information
for your server.
When you contact Lenovo for help, the machine type, model, and serial number information helps support
technicians to identify your server and provide faster service.
The machine type, model, and serial number label is attached on the pull-out information card, which is a
small plastic tab and can be slid out of the front of the chassis. The following illustrations are samples of the
machine type, model, and serial number labels on server models with different hard disk drive configurations.
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
CPU
Mem
PSU
Figure 2. Label on server models with 3.5-inch hard disk drives
Chapter 3. Product overview 13
Download from Www.Somanuals.com. All Manuals Search And Download.
PSU
Mem
CPU
Figure 3. Label on server models with 2.5-inch hard disk drives
Front view of the server
This topic provides information to help you locate the parts on the front of the server.
The front view of the server varies by model. The illustrations in this topic show the server front views
based on the supported hard disk drives:
• Front view of server models with 3.5-inch hard disk drives
• Front view of server models with 2.5-inch hard disk drives
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
Front view of server models with 3.5-inch hard disk drives
The following illustration shows the front view of server models with 3.5-inch hard disk drives.
PSU
Mem CPU
Figure 4. Front view of server models with 3.5-inch hard disk drives
1 Front panel
5 Right rack handle
2 Intelligent Diagnostics Module
3 Pull-out information card
6 3.5-inch hard disk drive area
7 Left rack handle
4 Slim optical drive (available in some models)
14 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Front panel
For detailed information about the controls, connectors, and status LEDs on the front panel, see “Front
2 Intelligent Diagnostics Module
3 Pull-out information card
The machine type, model, and serial number label of the server is attached on the pull-out information card.
4 Slim optical drive
Some server models come with a slim SATA optical drive.
5 Right rack handle
7 Left rack handle
If your server is installed in a rack cabinet, you can use the rack handles to slide the server out of the rack
cabinet; or use the rack handles and screws to secure the server in the rack cabinet so that the server
cannot slide out, especially in vibration-prone areas. For more information, refer to the Rack Installation
Instructions that comes with your server.
6 3.5-inch hard disk drive area
The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. The
number of the installed hard disk drives in your server varies by model. The vacant hard disk drive bays are
occupied by dummy hard disk drive trays.
The hard disk drive bay numbers are marked on the top edge of the front bezel.
Figure 5. 3.5-inch hard disk drive bay numbers (top view of the server)
Chapter 3. Product overview 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Front view of server models with 2.5-inch hard disk drives
The following illustration shows the front view of server models with 2.5-inch hard disk drives.
PSU
Mem CPU
6
Figure 6. Front view of server models with 2.5-inch hard disk drives
1 Front panel
5 2.5-inch hard disk drive area
2 Pull-out information card
3 Intelligent Diagnostics Module
4 Right rack handle
6 Slim optical drive (available in some models)
7 Left rack handle
1 Front panel
For detailed information about the controls, connectors, and status LEDs on the front panel, see “Front
2 Pull-out information card
The machine type, model, and serial number label of the server is attached on the pull-out information card.
3 Intelligent Diagnostics Module
4 Right rack handle
7 Left rack handle
If your server is installed in a rack cabinet, you can use the rack handles to slide the server out of the rack
cabinet; or use the rack handles and screws to secure the server in the rack cabinet so that the server
cannot slide out, especially in vibration-prone areas. For more information, refer to the Rack Installation
Instructions that comes with your server.
16 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5 2.5-inch hard disk drive area
The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. The
number of the installed hard disk drives in your server varies by model. The vacant hard disk drive bays are
occupied by dummy hard disk drive trays.
The hard disk drive bay numbers are marked on the top edge of the front bezel.
0
1
2
3
4
5
0
1
2
3
4
5
Figure 7. 2.5-inch hard disk drive bay numbers (top view of the server)
6 Slim optical drive
Some server models come with a slim SATA optical drive.
Front panel
This topic provides information to help you locate the controls, connectors, and LEDs on the front panel of
the server.
The following illustration shows the controls, connectors, and LEDs on the front panel of the server.
Figure 8. Front panel
1 Power switch with power status LED
2 ID button with ID LED
5 System error LED
6 Front USB connector 1
7 Front USB connector 2
8 Front VGA DB-15 connector
3 Network Interface Controller (NIC) 1 status LED
4 NIC 2 status LED
Note: The front VGA DB-15 connector is only available in server models with 2.5-inch hard disk drives.
Chapter 3. Product overview 17
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Power switch with power status LED
You can press the power switch to turn on the server when you finish setting up the server. You also can
hold the power switch for several seconds to turn off the server if you cannot turn it off from the operating
system. See Chapter 4 “Turning on and turning off the server” on page 43. The power status LED helps you
to determine the current power status.
Power status LED
Description
Color
Green
None
Green
The server is on.
The server is off.
On
Off
Blinking
The server is in ACPI S1 mode, which also is known
as Power On Suspend (POS) mode. In this mode, the
microprocessor is not working while other hardware
devices are still working.
2 ID button with ID LED
When you press the ID button, the ID LEDs on both the front and rear of the server are lit to help you locate
the server among other servers. You also can turn on the ID LEDs using a remote management program
for server presence detection.
ID LED
On
Description
The server is identified.
The ID LED is not in use or the server is not identified.
Color
Blue
None
Off
3 NIC 1 status LED
4 NIC 2 status LED
The two NIC status LEDs indicate the LAN status for the Ethernet connector 1 and Ethernet connector 2
on the rear panel of the server.
Description
The server is connected to a LAN.
The server is disconnected from a LAN.
The LAN is connected and active.
NIC status LED
Color
Green
None
Green
On
Off
Blinking
5 System error LED
The system error LED helps you to determine if there are any system errors.
Description
System error LED
Color
Amber
None
On
Off
A main component has failed.
The server is off or the server is on and is working
correctly.
18 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Front USB connector 1
7 Front USB connector 2
Used to attach a USB-compatible device, such as a USB keyboard, mouse, scanner, or printer. If you
have more than six USB devices, you can purchase a USB hub, which you can use to connect additional
USB devices.
8 Front VGA DB-15 connector
Used to attach a VGA-compatible video device, such as a VGA monitor.
Intelligent Diagnostics Module
This topic provides information about the Intelligent Diagnostics Module (hereinafter referred to as the IDM)
and the diagnostic LEDs on the module. Many errors are first indicated by a lit error LED on the diagnostic
panel of the server. If an LED is lit, one or more LEDs elsewhere in the server might also be lit to direct you to
The following illustration shows the location of the IDM and the diagnostic LEDs on the IDM panel.
Depending on the model, your server might look slightly different from the illustration in this topic.
Mem CPU
PSU
PSU
Mem CPU
Figure 9. IDM panel
1 Power supply error LED
2 Ambient temperature limit LED
3 System fan error LED
4 Memory module status LED
5 Microprocessor status LED
1 Power supply error LED
When the power supply error LED is lit in amber, it indicates that there is a power supply problem. To identify
the failing power supply, check the status LED near the power cord connector on the redundant power
supply. When the status LED is lit in green, it indicates that the power supply is working correctly. When the
status LED is lit in amber, it indicates that the power supply is likely to fail or has failed.
Chapter 3. Product overview 19
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Ambient temperature limit LED
When this LED is lit in amber, it indicates that the ambient temperature is below 7°C (44.6°F) or over 40°C
(104°F), which is not proper for server operation.
3 System fan error LED
When the system fan error LED is lit in amber, it indicates that one or more system fans are operating
slowly or have failed. To identify the failing system fan(s), check the status LEDs on the system board.
4 Memory module status LED
When the memory module status LED is lit in amber, it indicates that one or more memory modules are
overheated.
5 Microprocessor status LED (also known as CPU error LED)
When the microprocessor status LED is lit in amber, it indicates that one or more microprocessors are
overheated.
Rear view of the server
This topic provides information to help you locate the connectors and components on the rear of your server.
The following illustration shows the rear view of the server with two hot-swap power supplies.
9
8
Figure 10. Rear view of the server
1 Hot-swap redundant power supply 2 (available in 7 VGA DB-15 connector
some models)
2 Hot-swap redundant power supply 1
3 Low-profile PCI Express card slot
4 PCI Express card slot
8 Ethernet connector 1 (RJ-45)
9 Ethernet connector 0 for system management (RJ-45)
10 Serial port
11 ID LED
5 Ethernet connector 2 (RJ-45)
6 USB connectors (4)
1 Hot-swap redundant power supply 2 (available in some models)
2 Hot-swap redundant power supply 1
The hot-swap redundant power supplies help you avoid significant interruption to the operation of the
system when a power supply fails. You can purchase a hot-swap redundant power supply option directly
from Lenovo and install the power supply to provide power redundancy without turning off the server.
20 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
On each hot-swap redundant power supply, there is a status LED near the power cord connector. When the
LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly. When the LED
is lit in amber, it indicates that the hot-swap redundant power supply is likely to fail or has failed.
3 Low-profile PCI Express card slot
It is recommended to attach a RAID card to the low-profile PCI Express card slot.
Physical link width
Negotiable link width
Supported card length and height
x8
x4, x2, x1
Low-profile card
4 PCI Express card slot
Used to attach an Ethernet card or any other supported PCI Express card.
Physical link width
Negotiable link width
Supported card length and height
x16
x16, x8, x4, x2, x1
Half-length, full-height card
5
8
9 Ethernet connectors (RJ-45)
Used to attach an Ethernet cable for a LAN. Each Ethernet connector has two status LEDs to help you
identify the Ethernet connectivity, activity, and connection speed.
Notes:
• The Ethernet connector 0 (callout 9 ) marked with “MGMT” is for system management. If you want to use
remote management functions, you need to connect an Ethernet cable to the Ethernet connector 0.
• The Ethernet connector 0 for system management is 82574L by default. If you have selected share mode
for the 82574L Ethernet connector in the Setup Utility program, you can use it as an ordinary Ethernet
connector with 100 Mbps network connectivity. However, teaming with other Ethernet connectors is not
supported if the management Ethernet connector is used as an ordinary Ethernet connector. For detailed
information about setting the mode of the Ethernet connector for system management, see “Setting the
Figure 11. Ethernet status LEDs
Ethernet status LED
1 Left
Description
Color
Amber
Status
The connection speed is 1000 Mbps.
The connection speed is 100 Mbps.
The connection speed is 10 Mbps.
The server is connected to a LAN.
The server is disconnected from a LAN.
The LAN is connected and active.
On
On
Off
On
Off
Green
None
Green
None
Green
2 Right
Blinking
Chapter 3. Product overview 21
Download from Www.Somanuals.com. All Manuals Search And Download.
6 USB connectors (4)
Used to attach a USB-compatible device, such as a USB keyboard, mouse, scanner, or printer. If you
have more than six USB devices, you can purchase a USB hub, which you can use to connect additional
USB devices.
7 VGA DB-15 connector
Used to attach a VGA-compatible video device, such as a VGA monitor.
10 Serial port
Used to attach a device that uses a 9-pin serial port.
11 ID LED
When you press the ID button, the ID LEDs on both the front and rear of the server are lit to help you locate
the server among other servers. You also can turn on the ID LEDs using a remote management program
for server presence detection.
ID LED
On
Description
The server is identified.
The ID LED is not in use or the server is not identified.
Color
Blue
None
Off
Server components
This topic provides information to help you locate the components of your server. For more information
To remove the server cover and the cooling shroud and gain access to the inside of the server, see
“Removing the server cover” on page 69 and “Removing and reinstalling the cooling shroud” on page 73.
The chassis configuration varies by model. The following illustrations show the two chassis configurations
based on the supported hard disk drives.
• Server models with 3.5-inch hot-swap hard disk drives
• Server models with 2.5-inch hot-swap hard disk drives
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
22 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Components of server models with 3.5-inch hot-swap hard disk drives
PSU
Mem
CPU
Figure 12. Components of server models with 3.5-inch hot-swap hard disk drives
1 Cooling shroud
11 Pull-out information card
12 3.5-inch hard disk drive bays
13 Intelligent Diagnostics Module
14 Front panel
2 Riser card assembly 1
3 PCI Express card (available in some models)
4 Riser card assembly 2
5 One or two hot-swap redundant power supplies
6 CPU2 DIMMs (vary by model)
7 Heat sinks (vary by model)
15 Left rack handle
16 System fans
17 CPU1 DIMMs (vary by model)
18 System board
8 Backplane for 3.5-inch hard disk drives
9 Right rack handle
19 System board battery
20 PCI Express card (available in some models)
10 Slim optical drive (available in some models)
Chapter 3. Product overview 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Components of server models with 2.5-inch hot-swap hard disk drives
CPU
Mem
PSU
Figure 13. Components of server models with 2.5-inch hot-swap hard disk drives
1 Cooling shroud
11 Pull-out information card
12 Front panel
2 Riser card assembly 1
3 PCI Express card (available in some models)
4 Riser card assembly 2
13 Left rack handle
14 System fans
5 One or two hot-swap redundant power supplies
6 Backplane for 2.5-inch hard disk drives
7 Right rack handle
15 CPU2 DIMMs (vary by model)
16 CPU1 DIMMs (vary by model)
17 Heat sinks (vary by model)
18 System board
8 2.5-inch hard disk drive bays
9 Intelligent Diagnostics Module
10 Slim optical drive (available in some models)
19 System board battery
20 PCI Express card (available in some models)
24 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot-swap hard disk drive status LEDs
Each hot-swap hard disk drive has two status LEDs on the front.
Figure 14. Hot-swap hard disk drive status LEDs
1 Hard disk drive activity LED
2 Hard disk drive RAID status LED
Description
Off
Off
The hard disk drive has failed or is
not present.
The hard disk drive is present but not
in use.
On, green
Off
Off
Blinking, green
On, green
The hard disk drive is active and data
is being transferred.
Blinking rapidly (about four flashes
per second), amber
The RAID controller is identifying the
hard disk drive.
On, green
On, amber
The RAID array has failed and cannot
be recovered. You need to recreate a
new array.
Blinking, green
The hard disk drive is being rebuilt.
Blinking slowly (about one flash per
second), amber
RAID card
This topic provides information to help you locate the connectors on a RAID card if you have one installed
on the riser card assembly 2.
Some server models come with a RAID card to provide advanced SATA/SAS hardware RAID functions to the
Note: The option kit for the RAID card is designed for different types of servers and might contain additional
cables that are not required for your server.
Your server supports the following RAID cards:
• ThinkServer RAID 500 Adapter (also known as ThinkServer 9240-8i RAID 0/1 Adapter)
• ThinkServer RAID 700 Adapter (also known as ThinkServer 9260-8i SAS RAID Adapter)
Chapter 3. Product overview 25
Download from Www.Somanuals.com. All Manuals Search And Download.
ThinkServer RAID 500 Adapter (also known as ThinkServer 9240-8i RAID 0/1 Adapter)
The following illustration shows the connectors on the ThinkServer RAID 500 Adapter.
Figure 15. ThinkServer RAID 500 Adapter
1 Port 0
3 ThinkServer RAID 500 Upgrade Key for Advanced RAID
connector
2 Port 1
1 Port 0
Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 29.
2 Port 1
Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 29.
3 ThinkServer RAID 500 Upgrade Key for Advanced RAID connector
Used to connect a ThinkServer RAID 500 Upgrade Key for Advanced RAID. See “Installing or removing the
26 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
ThinkServer RAID 700 Adapter (also known as ThinkServer 9260-8i SAS RAID Adapter)
The following illustration shows the connectors on the ThinkServer RAID 700 Adapter.
Figure 16. ThinkServer RAID 700 Adapter
1 Ports 7-4
3 ThinkServer RAID 700 Battery connector
2 Ports 3-0
1 Ports 7-4
Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 29.
2 Ports 3-0
Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 29.
3 ThinkServer RAID 700 Battery connector
Used to connect a ThinkServer RAID 700 Battery. See “Installing or removing the ThinkServer RAID 700
Hot-swap hard disk drive backplane
Your server comes with one of the following hot-swap hard disk drive bay and backplane configurations:
• Up to four 3.5-inch hot-swap SATA or SAS hard disk drives with one backplane
• Up to six 2.5-inch hot-swap SAS hard disk drives or SATA solid-state drives with one backplane
Backplane for 3.5-inch hard disk drives
This topic provides information to help you locate the connectors on the backplane for 3.5-inch hard disk
drives.
Chapter 3. Product overview 27
Download from Www.Somanuals.com. All Manuals Search And Download.
The following illustrations show the connectors on the backplane for 3.5-inch hard disk drives.
Figure 17. Front view of the backplane for 3.5-inch hard disk drives
1 Slot 0 for a 3.5-inch hard disk drive
3 Slot 2 for a 3.5-inch hard disk drive
2 Slot 1 for a 3.5-inch hard disk drive
4 Slot 3 for a 3.5-inch hard disk drive
Figure 18. Rear view of the backplane for 3.5-inch hard disk drives
1 8-pin power connector
3 Mini-SAS ports 0-3
2 Optical drive power connector
1 8-pin power connector
Used to connect a power cable to provide power to the backplane.
2 Optical drive power connector
Used to connect the power cable for the slim optical drive if the server has one installed.
3 Mini-SAS ports 0-3
Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the
hard disk drive 0 to hard disk drive 3.
Backplane for 2.5-inch hard disk drives
This topic provides information to help you locate the connectors on the backplane for 2.5-inch hard disk
drives.
28 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
The following illustrations show the connectors on the backplane for 2.5-inch hard disk drives.
Figure 19. Front view of the backplane for 2.5-inch hard disk drives
1 Slot 0 for a 2.5-inch hard disk drive
2 Slot 2 for a 2.5-inch hard disk drive
3 Slot 4 for a 2.5-inch hard disk drive
4 Slot 5 for a 2.5-inch hard disk drive
5 Slot 3 for a 2.5-inch hard disk drive
6 Slot 1 for a 2.5-inch hard disk drive
Figure 20. Rear view of the backplane for 2.5-inch hard disk drives
1 8-pin power connector
3 Mini-SAS ports 0-3
2 Mini-SAS ports 4-5
4 Optical drive power connector
1 8-pin power connector
Used to connect a power cable to provide power to the backplane.
2 Mini-SAS ports 4-5
Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the
hard disk drive 4 to hard disk drive 5.
3 Mini-SAS ports 0-3
Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the
hard disk drive 0 to hard disk drive 3.
4 Optical drive power connector
Used to connect the power cable for the slim optical drive if the server has one installed.
Mini-SAS to mini-SAS signal cable connections
This topic provides instructions on the following mini-SAS to mini-SAS signal cable connections:
• Connecting cables from the system board to the backplane
Chapter 3. Product overview 29
Download from Www.Somanuals.com. All Manuals Search And Download.
• Connecting cables from the RAID card to the backplane
Connecting cables from the system board to the backplane
To connect cables from the system board to the backplane, do the following:
1. Use one mini-SAS to mini-SAS signal cable. Connect one connector of the mini-SAS signal cable to the
SAS connector 0-3 on the system board. Then, connect the other connector of the mini-SAS signal
cable to the mini-SAS ports 0-3 on the hot-swap hard disk drive backplane.
2. If you have more than four hard disk drives installed, use the other mini-SAS to mini-SAS signal cable.
Connect one connector of the mini-SAS signal cable to the SAS connector 4-7 on the system board.
Then, connect the other connector of the mini-SAS signal cable to the mini-SAS ports 4-5 on the
hot-swap hard disk drive backplane.
Note: If you connect the mini-SAS to mini-SAS signal cables from the system board to the backplane,
you can configure RAID using the configuration utility for the ThinkServer RAID 300. See “Configuring
Connecting cables from the RAID card to the backplane
If your server has a supported RAID card installed, you can connect cables from the RAID card to the
backplane to support up to six hard disk drives. In this case, you can configure RAID for the hard disk
drives using the advanced hardware RAID functions.
Note: The option kit for the RAID card is designed for different types of servers and might contain additional
cables that are not required for your server.
Figure 21. Connecting cables from the RAID card to the backplane
To connect cables from the RAID card to the backplane, do one of the following depending on the type of
your RAID card:
• If you are using a ThinkServer RAID 700 Adapter, do the following:
1. Use one mini-SAS to mini-SAS signal cable. Connect the mini-SAS connector 3 on one end of the
cable to the ports 3-0 on the RAID card. Then, connect the mini-SAS connector 4 on the other end
of the cable to the mini-SAS ports 0-3 on the backplane.
2. If your server has more than four hard disk drives installed, use the other mini-SAS to mini-SAS
signal cable. Connect the mini-SAS connector 1 on one end of the cable to the ports 7-4 on the
RAID card. Then, connect the mini-SAS connector 2 on the other end of the cable to the mini-SAS
ports 4-5 on the backplane.
• If you are using a ThinkServer RAID 500 Adapter, do the following:
30 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Use one mini-SAS to mini-SAS signal cable. Connect the mini-SAS connector 1 on one end of the
cable to the port 0 on the RAID card. Then, connect the mini-SAS connector 2 on the other end of
the cable to the mini-SAS ports 0-3 on the backplane.
2. If your server has more than four hard disk drives installed, use the other mini-SAS to mini-SAS
signal cable. Connect the mini-SAS connector 3 on one end of the cable to the port 1 on the RAID
card. Then, connect the mini-SAS connector 4 on the other end of the cable to the mini-SAS ports
4-5 on the backplane.
Refer to the following topics for information about the connector locations:
•
•
•
System board components
The following illustration shows the component locations on the system board.
Figure 22. System board components
1 Front panel connector
17 Riser card assembly 1 slot
18 Riser card assembly 2 slot
2 Internal USB connector 1
19 Redundant power supply connector 1
20 Redundant power supply connector 2
3 Internal USB connector 2
4 Intelligent Diagnostics Module connector
Chapter 3. Product overview 31
Download from Www.Somanuals.com. All Manuals Search And Download.
21 Backplane power connector 1
22 Backplane power connector 2
23 System fan 7 connector
24 Microprocessor socket 2
25 System fan 6 connector
26 Memory slots (6)
5 Front VGA connector
6 SATA connector 0
7 SAS connector 4-7
8 SAS connector 0-3
9 System board battery
10 Platform Controller Hub (PCH)
11 Internal USB Type A connector 1
12 TMM Premium connector
13 Internal USB Type A connector 2
14 TPM connector
27 System fan 5 connector
28 System fan 3 connector
29 Microprocessor socket 1
30 System fan 2 connector
31 Memory slots (6)
15 iButton socket
16 ThinkServer Management Module
32 System fan 1 connector
1 Front panel connector
Used to connect the front panel cable.
2 Internal USB connector 1
Used to connect the front panel USB cable.
3 Internal USB connector 2
Reserved for the manufacturer.
4 Intelligent Diagnostics Module connector
Used to connect the cable of the Intelligent Diagnostics Module.
5 Front VGA connector
Used to connect the cable of the front VGA connector on the front panel of the server.
6 SATA connector 0
Used to connect the signal cable of the slim optical drive if the server has one installed.
7 SAS connector 4-7
Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the
hard disk drive 4 to hard disk drive 5.
8 SAS connector 0-3
Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the
hard disk drive 0 to hard disk drive 3.
32 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
9 System board battery
Your server has a special type of memory that maintains the date, time, and configuration information for
built-in features. The system board battery keeps the information active when you turn off the server.
10 Platform Controller Hub (PCH)
This chip on the system board serves as a PCH, which provides the data buffering and interface arbitration
required to ensure that system interfaces operate efficiently and provides the bandwidth necessary for
the system to achieve peak performance. The chip supports and provides many features, including the
onboard SAS software RAID.
11 Internal USB Type A connector 1
13 Internal USB Type A connector 2
Used to connect a device that uses a USB Type A connector. For example, in some situations, you might
want to connect a USB key directly to the system board. In this case, you can connect it to an internal
USB Type A connector.
12 TMM Premium connector
Used to connect a server option named ThinkServer Management Module Premium (TMM Premium) to
enable advanced remote management functions on your server. See “Installing or removing the ThinkServer
14 TPM connector
Used to connect a ThinkServer Trusted Platform Module (TPM), which is a security chip, to enhance server
15 iButton socket
Your server supports ThinkServer RAID 300, which includes onboard SAS software RAID levels 0, 1, and 10.
You also can activate onboard SAS software RAID 5 by installing a ThinkServer RAID 300 Upgrade Key for
Advanced RAID in the iButton socket. For more information, see “Installing or removing the ThinkServer
16 ThinkServer Management Module
With the integrated ThinkServer Management Module (hereinafter referred to as the TMM), no matter what
condition the server operating system is in and no matter if the server is on or off, as long as the server
is connected to network and an ac power source, the interaction with the TMM controlled servers can be
achieved through system network. The user can obtain the server hardware health information and SEL,
and is able to conduct the operations including turning on or off the server, restarting the server, locking
the power switch on the front panel, and so on. This part of the server management is independent of the
operating system and is called out-of-band management.
17 Riser card assembly 1 slot
Used to install the riser card assembly 1.
18 Riser card assembly 2 slot
Used to install the riser card assembly 2.
Chapter 3. Product overview 33
Download from Www.Somanuals.com. All Manuals Search And Download.
19 Redundant power supply connector 1
20 Redundant power supply connector 2
Used to connect a hot-swap redundant power supply.
21 Backplane power connector 1
Used to connect the power cable from the backplane.
22 Backplane power connector 2
Reserved for the manufacturer.
23 25 27 28 30 32 System fan connectors
Used to connect the cable of the corresponding system fan.
26 31 Memory slots
There are 12 memory slots on the system board. For more information, see “Memory module installation
24 Microprocessor socket 2
29 Microprocessor socket 1
If the server has two microprocessors, each of the microprocessor is secured in the microprocessor socket
on the system board and a heat sink is installed above the microprocessor to provide cooling. If the server
has only one microprocessor, the microprocessor socket 2 is protected by a microprocessor socket cover.
System board jumpers and switches
This topic provides information about the jumpers and switches on the system board.
A jumper is a short length of conductor used to set up or adjust printed circuit boards, such as the system
board of a computer. A jumper usually is encased in a non-conductive block of plastic for convenient use
and to avoid any possible damage to a live circuit. Jumper pins arranged in groups on the system board are
called jumper blocks. When two or more jumper pins are capped with a jumper, an electrical connection is
made between them and the equipment is thus instructed to activate certain settings accordingly.
34 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
The following illustration shows a jumper in the default setting position (pin 1 and pin 2). This is the correct
position for normal operation.
Figure 23. Default jumper setting
Chapter 3. Product overview 35
Download from Www.Somanuals.com. All Manuals Search And Download.
The following illustration shows the status of the jumpers and switches on the system board of your server.
You can configure, recover, enable, or disable some specific features of the system board by setting the
jumpers or moving the switches.
Figure 24. System board jumpers and switches
Table 1. System jumpers
1 Clear CMOS (Complementary Metal Oxide Semiconductor) jumper
3 Switches
2 ThinkServer Management Module Enable/Disable jumper
Attention: To set the jumpers or move switches, you need to remove the server cover to access the system
board. Do not open your server or attempt any repair before reading and understanding “Safety information”
1 Clear CMOS jumper
Used to clear CMOS and recover your server to the factory default settings.
Note: After clearing CMOS, your BIOS recovers to the factory default settings.
36 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
To clear CMOS, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Locate the Clear CMOS jumper on the system board. Then, remove any parts and disconnect any
cables that might impede your access to the jumper.
5. Move the clear CMOS jumper from the default normal position (pin 1 and pin 2) to the short-circuited
position (pin 2 and pin 3).
6. Wait more than five seconds and then move the Clear CMOS jumper back to the normal position
(pin 1 and pin 2).
7. Reinstall any parts and reconnect any cables. Then, reinstall the server cover. See “Completing the
8. Connect the server to an ac power source and wait about 30 seconds. Then, turn on the server. The
BIOS recovers to the factory default settings.
2 ThinkServer Management Module Enable/Disable jumper
When the ThinkServer Management Module Enable/Disable jumper (hereinafter referred to as the TMM
Enable/Disable jumper) is in the default normal position (pin 1 and pin 2), the server needs about 30 seconds
for the TMM to initialize whenever you connect the server to an ac power source. If you press the power
switch on the front panel during this period, the server will not start immediately; it will start after the TMM
initialization finishes. The TMM function is available in this situation.
If you move the TMM Enable/Disable jumper to pin 2 and pin 3, the TMM function is not available and the
server will be directly turned on when you press the power switch without waiting for the TMM to be ready.
Chapter 3. Product overview 37
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Switches
There are four switches on the system board of your server.
Figure 25. Switches
Table 2. Switches
1 BIOS recovery switch
3 Management Engine (ME) in force update switch
4 Reserved for the manufacturer
2 Clear password switch
1 BIOS recovery switch
Used to recover the BIOS if the power to your server is interrupted while the BIOS is being updated and your
server cannot start correctly.
2 Clear password switch
Used to erase forgotten passwords, such as the BIOS passwords.
38 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
To clear passwords, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Locate the Clear password switch on the system board. Then, remove any parts and disconnect any
cables that might impede your access to the switch.
5. Move the clear password switch from the default off position to the on position.
6. Wait more than five seconds and then move the clear password switch back to the off position.
7. Reinstall any parts and reconnect any cables. Then, reinstall the server cover. See “Completing the
8. Connect the server to an ac power source and wait about 30 seconds. Then, turn on the server. The
BIOS passwords are erased, including the administrator password and user password.
3 ME in force update switch
Used to update (flash) the ME.
The ME updating process usually is contained in the BIOS updating (flashing) process.
Note: Only some BIOS versions contain the parameters for updating the ME. If you want to update the ME,
ensure that your BIOS version contains the required parameters.
To update the ME, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Locate the ME in force update switch on the system board. Then, remove any parts and disconnect any
cables that might impede your access to the switch.
5. Move the ME in force update switch from the default off position to the on position.
6. Reinstall any parts and reconnect any cables. Then, reinstall the server cover. See “Completing the
7. Connect the server to an ac power source. Then, update the BIOS. See “Updating (flashing) the BIOS”
on page 52.
8. Repeat step 1 through step 4.
9. Move the ME in force update switch back to the off position.
10. Reinstall any parts and reconnect any cables. Then, reinstall the server cover. See “Completing the
11. Connect the server to an ac power source and turn on the server. The BIOS and ME have been
updated. You need to check and configure the BIOS settings for your specific needs. See “Using
System board LEDs
This topic helps you locate the LEDs on the system board.
Chapter 3. Product overview 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Depending on the model, your server might look slightly different from the illustration in this topic.
The server is designed so that LEDs remain lit when the server is connected to an ac power source but is
not turned on, provided that the power supply is operating correctly. This helps you isolate problems
when the server is not turned on. Many errors are first indicated by a lit error LED on the diagnostic panel
of the server. If an LED is lit, one or more LEDs elsewhere in the server might also be lit to direct you to
the source of the error.
The following illustration shows the ThinkServer Management Module status LED and system fan error LEDs
on the system board.
Figure 26. System board LEDs
1 ThinkServer Management Module status LED
2 System fan 7 error LED
5 System fan 3 error LED
6 System fan 2 error LED
7 System fan 1 error LED
3 System fan 6 error LED
4 System fan 5 error LED
1 ThinkServer Management Module status LED
This LED indicates the status of the onboard ThinkServer Management Module (TMM).
Description
ThinkServer Management Module
status LED
Color
The TMM is not ready.
On
Off
Green
None
Green
The TMM has no power or has failed.
The TMM is working.
Blinking
40 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
2 - 7 System fan error LEDs
When a system fan error LED on the system board is lit, it indicates that the corresponding system fan is
operating slowly or has failed. To solve the problem, you might need to reinstall or replace the system fan.
See “Replacing a system fan” on page 139. If it is a system board problem, contact the Lenovo Customer
Support Center.
Chapter 3. Product overview 41
Download from Www.Somanuals.com. All Manuals Search And Download.
42 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Turning on and turning off the server
This chapter provides information about turning on and turning off the server.
Turning on the server
The server can be turned on in one of the following ways:
• After you finish unpacking and setting up the server, connect it to an ac power source. Press the power
switch on the front panel to turn on the server. See “Front panel” on page 17. The server needs about
30 seconds for the TMM to initialize whenever you connect the server to an ac power source. If you
press the power switch on the front panel during this period, the server will not start immediately; it will
start after the TMM initialization finishes.
• When the Wake on LAN feature is enabled on the server that is connected to an ac power source and a
LAN, a network administrator can remotely turn on or wake up the server from a management console
using remote network management software.
• You also can use the related TMM feature to remotely turn on the server through the management LAN.
For more information about the TMM, refer to the ThinkServer Management Module User Guide, which is
available for download at:
Turning off the server
CAUTION:
The power control button on the device and the power switch on the power supply do not turn off
the electrical current supplied to the device. The device also might have more than one power
cord. To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.
The server can be turned off in one of the following ways:
• Turn off the server from the operating system if your operating system supports this feature. After an
orderly shutdown of the operating system, the server will turn off automatically. For instructions on how
to shut down your specific operating system, refer to the related documentation or help system for
the operating system.
• Press the power switch on the front panel to start an orderly shutdown of the operating system and turn
off the server, if your operating system supports this feature.
• If your server stops responding and you cannot turn it off, press and hold the power switch on the
front panel for four seconds or more. If you still cannot turn off the server, disconnect all power cords
from the server.
• If the server is connected to a LAN, a network administrator can remotely turn off the server from a
management console using remote network management software.
• You also can use the related TMM feature to remotely turn off the server through the management LAN.
For more information about the TMM, refer to the ThinkServer Management Module User Guide, which is
available for download at:
© Copyright Lenovo 2012
43
Download from Www.Somanuals.com. All Manuals Search And Download.
• The server might be turned off as an automatic response to a critical system failure.
Notes:
• When you turn off the server and leave it connected to an ac power source, the server also can respond
to a remote request to turn on the server. To remove all power from the server, you must disconnect
the server from the ac power source.
• For information about your specific operating system, refer to the related documentation or help system
for the operating system.
44 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Configuring the server
This chapter provides the following information to help you configure the server:
•
•
•
•
•
•
Using the Setup Utility program
This topic provides information about using the Setup Utility program.
The Setup Utility program is part of the server firmware. You can use the Setup Utility program to view and
change the configuration settings of your server, regardless of which operating system you are using.
However, the operating system settings might override any similar settings in the Setup Utility program.
Starting the Setup Utility program
This topic provides instructions on how to start the Setup Utility program.
To start the Setup Utility program, do the following:
1. Connect the server to an ac power source and press the power switch on the front panel to turn on the
2. Press the F1 key as soon as you see the logo screen. Then, wait for several seconds, and the Setup
Utility program opens. If you have set a password, you need to type the correct password to enter the
Viewing information in the Setup Utility program
The Setup Utility program menu lists various items about the system configuration. Select a desired item
to view information or change settings.
When working with the Setup Utility program, you must use the keyboard. The keys used to perform various
tasks are displayed on the right bottom pane of each screen. You also can press the F1 key for general help
about the keys. For most items, the corresponding help message is displayed on the right top pane of the
screen when the item is selected. If the item has submenus, you can display the submenus by pressing Enter.
You can view the following information about your specific server model in the Setup Utility program:
• The Main menu lists information about the BIOS and BMC, total memory size, and system date and time.
• On the Advanced menu:
– Select Processor Configuration and follow the instructions on the screen to view information about
the installed microprocessor and its supported technologies.
– Select Memory Configuration and follow the instructions on the screen to view information about the
installed memory modules.
© Copyright Lenovo 2012
45
Download from Www.Somanuals.com. All Manuals Search And Download.
– Select SATA/SAS Configuration and follow the instructions on the screen to view information about
the installed SATA or SAS devices, such as a hard disk drive or an optical drive.
• On the Server Management menu, select System Information to view information about your system.
Setup Utility program interface
This topic provides general information about the menus and items in the Setup Utility program.
Depending on the BIOS version of your server, some menu or item information might differ slightly from
the information in this topic.
Notes:
• The default settings already are optimized for you. Use the default value for any item you are not familiar
with. Do not change the value of unfamiliar items to avoid unexpected problems. If you consider
changing the server configuration, proceed with extreme caution. Setting the configuration incorrectly
might cause unexpected results. If you cannot turn on the server because of incorrect BIOS settings,
use the Clear CMOS jumper to restore the BIOS settings to the factory default settings. See “System
• If you have changed any hardware in the server, you might need to reflash the BIOS, the BMC firmware,
and the FRU/Sensor Data Records (SDR).
The Setup Utility program main interface consists of the following menus:
•
•
•
•
•
•
•
Lenovo provides the BIOS update utility on the Lenovo Support Web site. You can download the BIOS
update utility to update the BIOS if the newer BIOS version specifically solves a problem you have. See
If the power to your server is interrupted while the BIOS is being updated and your server cannot start
correctly, use the BIOS recovery switch to recover from a BIOS update failure. See “System board jumpers
Main menu
After entering the Setup Utility program, you can see the Main menu, which lists basic information about
the BIOS and BMC, total memory size, and system date and time.
To set the system date and time on the Main menu, see “Setting the system date and time” on page 48.
Advanced menu
You can view or change various server component settings on the Advanced menu in the Setup Utility
program. The Advanced menu contains various configuration submenus and items. On each submenu,
press Enter to show selectable options and select a desired option by using the up and down arrow
keys or type desired values from the keyboard. Some items are displayed on the menu only if the server
supports the corresponding features.
46 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
• Enabled means that the function is configured.
• Disabled means that the function is not configured.
The Advanced menu contains the following submenus. For more information, enter the corresponding
submenu and refer to the instructions on the screen.
• PCI Configuration: View and set PCI configuration parameters.
• ACPI Configuration: View and set ACPI configuration parameters.
• Processor Configuration: View information about the installed microprocessor(s) and set microprocessor
configuration parameters.
• Memory Configuration: View information about the installed memory modules and set memory
configuration parameters.
• Chipset Configuration: View and set chipset configuration parameters.
• SATA/SAS Configuration: View information about the installed SATA or SAS devices and set SATA or
SAS configuration parameters.
• USB Configuration: View and set USB configuration parameters, such as enabling or disabling USB
devices.
• Super IO Configuration: View and set serial port configuration parameters.
• Serial Port Console Redirection: View and set configuration parameters for the serial port console
redirection.
Security menu
You can set passwords and configure the TPM function on the Security menu in the Setup Utility program.
For each menu item, press Enter to show selectable options and select a desired option by using the up and
down arrow keys or type desired values from the keyboard. Some items are displayed on the menu only if
the server supports the corresponding features.
Notes:
• Enabled means that the function is configured.
• Disabled means that the function is not configured.
The Security menu contains the following items:
• Administrator Password: Set an administrator password to protect against unauthorized access to
• User Password: Set a user password to protect against unauthorized access to your server. See “Using
• TPM/TCM: Configure the TPM function if your server has a TPM installed in the TPM connector on the
Server Management menu
You can view system information and view or change event log and BMC settings on the Server
Management menu in the Setup Utility program. On each submenu, press Enter to view the information or
show selectable options and select a desired option by using the up and down arrow keys. Some items are
displayed on the menu only if the server supports the corresponding features.
The Server Management menu contains the following submenus. For more information, enter the
corresponding submenu and refer to the instructions on the screen.
• Erase SEL: Erase system event log (SEL).
Chapter 5. Configuring the server 47
Download from Www.Somanuals.com. All Manuals Search And Download.
• System Information: View basic information about your server.
• BMC Network Configuration: Set BMC configuration parameters.
Boot Options menu
The Boot Options menu in the Setup Utility program provides an interface to help you view or change the
server startup options, including the startup sequence and boot priority for various devices. Changes in the
startup options take effect when the server starts.
The startup sequence specifies the order in which the server checks devices to find a boot record. The server
starts from the first boot record that it finds. For example, you can define a startup sequence that checks a
disc in the optical drive, then checks the hard disk drive, and then checks a network device. For information
about setting the startup sequence or selecting a startup device, see “Selecting a startup device” on page 50.
Boot Manager menu
The Boot Manager menu in the Setup Utility program lists all the bootable devices installed in your server
and the listed items vary depending on your server configuration. If you select a desired device listed on this
menu, the server will start from the device you select.
You can press F12 when turning on the server and select a temporary startup device from the boot device
Save & Exit menu
After you finish viewing or changing settings in the Setup Utility program, you can choose a desired
action from the Save & Exit menu to save changes, discard changes, or load default values, and exit the
program. Press Enter to select the item on the Save & Exit menu and then select Yes when prompted to
confirm the action. For information about exiting the Setup Utility program, see “Exiting the Setup Utility
The Save & Exit menu contains the following items:
• Save Changes and Exit: Save changes and exit the Setup Utility program.
• Save Changes and Reset: Save changes and then continue with the configuration in the Setup Utility
program.
• Discard Changes and Exit: Discard changes, load previous values, and then exit the Setup Utility
program.
• Discard Changes: Discard changes and load previous values.
• Restore Defaults: Return to the optimized default settings.
• Save as User Defaults: Save the current settings as user default values.
• Restore User Defaults: Restore the user default values for all the items.
Setting the system date and time
This topic provides instructions on how to set the system date and time in the Setup Utility program.
To set the system date and time in the Setup Utility program, do the following:
2. On the Main menu, select System Date or System Time.
3. Use the Tab key to switch between data elements and type the numbers from the keyboard to set the
system date and time.
4. Press F10 to save settings and exit the Setup Utility program.
48 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Using passwords
By using the Setup Utility program, you can set a password to prevent unauthorized access to your server.
You do not have to set a password to use your server. However, using a password improves computing
security. If you decide to set a password, read the following topics.
Setup Utility program password types
The following types of passwords are available in the Setup Utility program:
• Administrator password
Setting an administrator password deters unauthorized users from changing configuration settings. If you
are responsible for maintaining the configuration settings of several computers, you might want to set
an administrator password. When an administrator password is set, you are prompted to type a valid
password each time you try to access the Setup Utility program. The Setup Utility program cannot
be accessed until a valid password is typed in.
• User password
When a user password is set, the server cannot be used until a valid password is typed in.
Note: If both the administrator password and user password are set, you can type either password to use
the server. However, you must use your administrator password to change any configuration settings.
Password considerations
For security reasons, it is recommended to use a strong password that cannot be easily compromised.
Notes:
• The Setup Utility program passwords are not case sensitive.
• The server supports Setup Utility program passwords that consist of three to 20 characters.
To set a strong password, use the following guidelines:
• Have at least eight characters in length
• Contain at least one alphabetic character and one numeric character
• Not be your name or your user name
• Not be a common word or a common name
• Be significantly different from your previous passwords
Besides the alphabetic characters (a-z) and numeric characters (0-9), the server also supports characters
typed using special keys on the keyboard for a password. Refer to the help message on the screen when
setting a password to determine the valid special characters.
Setting, changing, or deleting a password
This topic provides instructions on how to set, change, or delete a password in the Setup Utility program.
To set, change, or delete a password in the Setup Utility program, do the following:
2. On the Security menu, select Administrator Password to set an administrator password or select
User Password to set a user password.
change a password.
Chapter 5. Configuring the server 49
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If you want to delete a password, type your current password. Press Enter when you are prompted
to type a new password. Then, press Enter to confirm the new password. The previous password
will be cleared.
Note: For security reasons, it is recommended that you always set a password for your server.
5. Press F10 to save settings and exit the Setup Utility program.
If you have forgotten the password, you can use the Clear password switch on the system board to erase the
password. See “System board jumpers and switches” on page 34. Then, set a new password for the server.
Selecting a startup device
If your server does not start up from a desired device such as the disc or hard disk drive as expected, do one
of the following to select the startup device you want.
Note: Not all discs, hard disk drives, or other removable devices are bootable.
• To select a temporary startup device, do the following:
Note: Selecting a startup device using the following method does not permanently change the startup
sequence.
1. Turn on or restart your server.
2. When you see the logo screen, press F10 if your server is connected to a network and you want to
start up the server from the network. Otherwise, press F12 to display the boot menu. The boot
device selection window opens.
3. In the boot device selection window, use the up and down arrow keys on the keyboard to switch
between the selections. Press Enter to select the device of your choice. Then, the server will start
up from the selected device.
• To view or permanently change the configured startup device sequence, do the following:
2. On the Boot Options menu, follow the instructions on the screen to set the startup device for Boot
Option #1 to Boot Option #5 depending on your needs. You also can set the boot priority for various
3. Press F10 to save settings and exit the Setup Utility program. The server will follow the startup device
sequence you have set each time you turn on the server.
Configuring the TPM function
The TPM works as a hardware security solution to help you to encrypt data and protect the server. The TPM
function is only available when there is a TPM installed in your server. See “Installing the ThinkServer Trusted
After installing a TPM, you need to check if the TPM function is enabled in the Setup Utility program.
To enable the TPM function in the Setup Utility program, do the following:
2. On the Security menu, select TPM/TCM ➙ TPM Support. Ensure that TPM Support is set to Enabled.
3. When TPM Support is set to Enabled, the TPM State item is displayed. Set TPM State to Enabled.
4. Press F10 to save settings and exit the Setup Utility program. The server will restart to enable the
TPM function.
50 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the mode of the Ethernet connector 0
The Ethernet connector 0 on the rear of the server is for system management. If you want to use remote
management functions, you need to connect an Ethernet cable to the Ethernet connector 0. See “Rear
The Ethernet connector 0 for system management is 82574L by default. If you have selected share mode
for the 82574L Ethernet connector in the Setup Utility program, you can use the connector as an ordinary
Ethernet connector with 100 Mbps network connectivity. However, teaming with other Ethernet connectors
is not supported if the management Ethernet connector is used as an ordinary Ethernet connector.
To set the mode of the Ethernet connector 0 in the Setup Utility program, do the following:
2. On the Server Management menu, select BMC Network Configuration ➙ BMC LAN Share Setting.
3. Do one of the following:
• If you want to use the Ethernet connector 0 as an ordinary Ethernet connector, select Shared.
• If you want to use the Ethernet connector 0 as a dedicated system management Ethernet connector,
select Dedicated.
4. Press F10 to save settings and exit the Setup Utility program.
Exiting the Setup Utility program
After you finish viewing or changing settings, press Esc to return to the Setup Utility program main interface.
If you are on a nested submenu, press Esc repeatedly until you reach the main interface. Then, you can do
one of the following to exit the Setup Utility program:
• If you want to save the new settings and exit the Setup Utility program, press F10 or select Save & Exit ➙
Save Changes and Exit. Otherwise, your changes will not be saved.
• If you do not want to save the new settings, select Save & Exit ➙ Discard Changes and Exit.
• If you want to return to the default settings, press F9 or select Save & Exit ➙ Restore Defaults.
For more information about the Save & Exit menu in the Setup Utility program, see “Save & Exit menu”
on page 48.
Updating or recovering the BIOS
This topic provides instructions on how to update the BIOS and how to recover from a POST and BIOS
update failure.
System programs are the basic layer of software built into your server. System programs include the POST,
the UEFI BIOS, the Setup Utility program, and the TMM firmware. The POST is a set of tests and procedures
that are performed each time you turn on your server. The UEFI BIOS is a layer of software that translates
instructions from other layers of software into electrical signals that the server hardware can execute. You
can use the Setup Utility program to view or change the configuration settings of your server. See “Using the
Lenovo might make changes and enhancements to the BIOS and TMM firmware. When updates are released,
they are available for download on the Lenovo Web site at http://www.lenovo.com/drivers. You can update
the server firmware by downloading an update package and following the instructions on the Web page.
You also can use the Firmware Updater program to help you keep the server firmware up-to-date. See
Chapter 5. Configuring the server 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Updating (flashing) the BIOS
This topic provides instructions on how to update (flash) the BIOS.
Notes:
• Update the BIOS on your server only if the newer BIOS version specifically solves a problem you have.
We do not recommend BIOS updates for servers that do not need them. You can view the updated
information for the new BIOS version in the installation instructions for the BIOS update package.
• Downgrading the BIOS to an earlier version is not recommended and might not be supported. An earlier
BIOS version might not support the latest system configurations.
• If the power to your server is interrupted while the POST and BIOS are being updated, your server might
not restart correctly. Ensure that you perform the BIOS update procedure in an environment with a
steady power supply. Besides, ensure that your server can restart successfully without encountering
hardware problems.
• If you have updated the BIOS firmware, all the BIOS settings become the default settings of the updated
BIOS version. You need to check and reconfigure the BIOS settings for your specific needs. You can
select Save as User Defaults on the Save & Exit menu in the Setup Utility program to save your current
BIOS settings as user default values before updating the BIOS. Then, you can select Restore User
Defaults on the Save & Exit menu in the Setup Utility program to restore the user default values after
updating the BIOS. In this case, you can keep your previous BIOS settings and do not need to reconfigure
the settings after updating the BIOS. You also can note down your specific BIOS settings before updating
the BIOS for an easier reconfiguration in the new BIOS version.
To update (flash) the BIOS, do the following:
1. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to locate the BIOS
update package.
2. Download the BIOS update package and the installation instructions in a TXT file.
3. Print the TXT file that contains the installation instructions and follow the instructions to update (flash)
the BIOS.
4. Do one of the following after the BIOS update process is completed:
• If you have saved your BIOS settings as user default values before updating the BIOS, select Restore
User Defaults on the Save & Exit menu in the Setup Utility program to restore the user default
values. Then, check if the user default values meet your current requirements.
• Check and reconfigure the BIOS settings for your specific needs based on your note or refer to
Recovering from a BIOS update failure
If the power to your server is interrupted while the BIOS is being updated, your server might not restart
correctly. If this happens, perform the following procedure to recover from the BIOS update failure.
Note: If the operating system of your server is installed under EFI mode, you need to reinstall the operating
system after recovering the BIOS.
To recover from a BIOS update failure, do the following:
1. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to download a BIOS
update package. Then, put the amiboot.rom file contained in the package into the root directory of
a bootable USB key.
2. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
3. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
52 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
page 34. Then, remove any parts and disconnect any cables that might impede your access to the
switch.
6. Move the BIOS recovery switch from the default off position to the on position.
7. Reinstall any parts and reconnect any cables. Then, reinstall the server cover. See “Completing the
8. Connect the server to an ac power source and then start the server from the bootable USB key that
contains the amiboot.rom file. The recovery process starts. After the recovery process is completed,
your server will automatically turn off.
9. Repeat step 2 through step 5.
10. Move the BIOS recovery switch back to the off position.
11. Reinstall any parts and reconnect any cables. Then, reinstall the server cover. See “Completing the
12. Connect the server to an ac power source and turn on the server. The BIOS settings recover to the
factory default settings. You need to check and configure the BIOS settings for your specific needs. See
Note: If you cannot recover the BIOS after using the instructions in this topic, the BIOS read-only memory
(ROM) might be damaged and you need to replace the system board. Contact the Lenovo Customer
Support Center.
Using the ThinkServer EasyStartup program
This topic guides you to use the ThinkServer EasyStartup program to set up and configure your server.
The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported
Windows and Linux operating systems and device drivers on your server. The program works in conjunction
with your Windows or Linux operating system installation disc to automate the process of installing the
operating system and associated device drivers. This program is provided with your server on a self-starting
(bootable) ThinkServer EasyStartup DVD. The user guide for the program also is on the DVD and can be
accessed directly from the program interface.
If you do not have a ThinkServer EasyStartup DVD, you also can download an ISO image from the Lenovo
Support Web site and make a disc by yourself.
To download the ThinkServer EasyStartup program image and burn it into a disc, do the following:
ThinkServer EasyStartup program.
2. Download the ISO image for the ThinkServer EasyStartup program and the readme file. The readme file
contains important information about the ThinkServer EasyStartup program.
3. Print the readme file and read it carefully.
4. Use an optical drive and any DVD burning software to create a bootable disc with the ISO image.
Features of the ThinkServer EasyStartup program
This topic lists the features of the ThinkServer EasyStartup program.
The ThinkServer EasyStartup program has the following features:
• Contained in a self-starting (bootable) DVD
Chapter 5. Configuring the server 53
Download from Www.Somanuals.com. All Manuals Search And Download.
• Easy-to-use, language-selectable interface
• Integrated help system and user guide
• Automatic hardware detection
• Contains the RAID configuration utility
• Provides device drivers based on the server model and detected devices
• Downloads device drivers from the ThinkServer EasyStartup DVD according to the operating system
or add-on device
• Selectable partition size and file system type
• Support for multiple operating systems
• Ability to install the operating system and device drivers in an unattended mode to save time
• Ability to create a reuseable response file that can be used with similarly configured Lenovo servers to
make future installations even faster
Starting the ThinkServer EasyStartup program
This topic provides instructions on how to start the ThinkServer EasyStartup program. After you start the
program and enter the main interface, click User Guide for detailed information about how to use this
program to help you configure the server and install an operating system.
To start the ThinkServer EasyStartup program, do the following:
1. Insert the ThinkServer EasyStartup DVD into an optical drive, set the optical drive as the first startup
device, and start your server from the DVD in the optical drive. See “Selecting a startup device” on
page 50.
2. Wait for the program to load. Then, you will be prompted for the following selections:
• The language in which you want to view the program
• The language of the keyboard layout you will be using with the program
Note: The supported languages and keyboard layouts for the ThinkServer EasyStartup program are
Dutch, English, French, German, Italian, Japanese, Russian, Spanish, and Turkish. Your ThinkServer
EasyStartup DVD might be English only. In this case, the keyboard layout should be English.
3. After selecting the language and keyboard layout, click OK. Then, you will see one or more reminders
or messages about configuring storage devices. Click Next until you are presented with the Lenovo
License Agreement. Read the Lenovo License Agreement carefully. In order to continue, you must
accept the terms by clicking Agree. Then, the Date and time window opens.
4. Set the current date and time and click OK. The Start option window opens.
5. The Start option window provides the following selections:
• Continue to the main interface.
• Install the operating system using a pre-existing response file.
• Configure RAID using a pre-existing response file.
Read the explanations on the screen and select a desired option. Then, follow the instructions on the
screen. If this is the first time you are using the ThinkServer EasyStartup program, select the option to
continue to the main interface and view the compatibility notes and user guide.
Notes:
• Functionality and supported operating systems vary depending on the version of the ThinkServer
EasyStartup program. From the main interface of the program, click Compatibility notes to view the
information about the RAID controllers, operating systems, and server configurations supported by the
54 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
specific version of the program; and click User Guide to view the various functions and learn how to
use the program.
• Before using the ThinkServer EasyStartup program to install an operating system, ensure that any external
storage devices and fiber channels are configured correctly.
The ThinkServer EasyStartup program main interface provides the following menus on the left pane of
the screen:
• Home
This menu is the welcome page that contains some general descriptions about the program and the
Lenovo copyright and trademark statements.
• Compatibility notes
This menu provides information about the RAID controllers, operating systems, and server configurations
supported by the version of the program you are using.
• User Guide
This menu provides information about the features of the program and instructions on how to use the
program.
• Hardware list
This menu displays a list of hardware devices detected by the program.
• Configure RAID
This menu guides you to configure RAID or view the current RAID configuration and make changes
if needed.
• Install operating system
This menu displays a series of choices and prompts to collect information required for operating system
installation, prepares the hard disk drive for installation, and then initiates the installation process using
your operating system installation disc.
• Download drivers
This menu helps you download the required device drivers from the ThinkServer EasyStartup DVD to a
removable storage device so that you can easily get the drivers for server configuration when you need
them.
Note: The most up-to-date device drivers for various server models are always available for download on
the Lenovo Support Web site at:
• About
This menu provides the version information and legal notices.
Using the ThinkServer EasyStartup program on a Windows operating
system
You can run the ThinkServer EasyStartup DVD on a Windows operating system with the Internet Explorer® 6.0
Web browser or a later version installed. Enter the operating system and insert the ThinkServer EasyStartup
DVD into an internal or external optical drive. The DVD starts automatically in most environments. If the DVD
fails to start, open the launch.exe file located in the root directory of the DVD.
Notes:
• You should read and accept the Lenovo License Agreement when prompted.
Chapter 5. Configuring the server 55
Download from Www.Somanuals.com. All Manuals Search And Download.
• On the Microsoft Windows Server® 2003 operating system, you might need to add the Uniform Resource
Locator (URL) for the ThinkServer EasyStartup program Web page to the trusted Web site list so that
the page can open correctly.
You can do the following when using the ThinkServer EasyStartup program on a Windows operating system.
For detailed information, refer to the help system.
• View a general introduction to your ThinkServer server model and the specific server configuration
information.
• View general guidance on how to use the ThinkServer EasyStartup DVD.
• Download the required device drivers to a removable storage device so that you can easily get the
drivers for server configuration when you need them, especially when you finish installing an operating
system without using the ThinkServer EasyStartup DVD and need appropriate device drivers to configure
your server.
• Install the required device drivers directly on the server on which you are running the ThinkServer
EasyStartup DVD.
• View information about all server models supported by the ThinkServer EasyStartup program and
information about the device drivers for each server model, including the driver versions and driver
locations in the root directory of the ThinkServer EasyStartup DVD.
Note: The most up-to-date device drivers for various server models are always available for download on
the Lenovo Support Web site at:
Configuring RAID
This topic provides information about RAID and the utility programs that are available for you to configure
RAID.
This topic contains the following items:
•
•
•
•
About RAID
RAID, an acronym for Redundant Array of Independent Disks, is a technology that provides increased
storage functions and reliability through redundancy. This is achieved by combining multiple hard disk drives
into a logical unit, where data is distributed across the drives in one of several ways called RAID levels.
When a group of independent physical hard disk drives are set up to use RAID technology, they are in a
RAID array. This array distributes data across multiple hard disk drives, but the array appears to the host
server as one single storage unit. Creating and using RAID arrays provides high performance, such as the
expedited I/O performance, because several drives can be accessed simultaneously.
RAID drive groups also improve data storage reliability and fault tolerance compared with single-drive
storage systems. Data loss resulting from a drive failure can be prevented by reconstructing missing data
from the remaining drives.
The following list describes some of the most commonly used RAID levels:
56 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
• RAID 0: block-level striping without parity or mirroring
Simple stripe sets are normally referred to as RAID 0. RAID 0 uses striping to provide high data
throughput, especially for large files in an environment that does not require fault tolerance. RAID 0 has no
redundancy and it provides improved performance and additional storage without fault tolerance. Any
drive failure destroys the array and the likelihood of failure increases with more drives in the array. RAID
0 does not implement error checking, so any error is uncorrectable. More drives in the array means
higher bandwidth, but greater risk of data loss.
RAID 0 requires a minimum number of two hard disk drives.
• RAID 1: mirroring without parity or striping
RAID 1 uses mirroring so that data written to one drive is simultaneously written to another drive. This is
good for small databases or other applications that require small capacity but complete data redundancy.
RAID 1 provides fault tolerance from disk errors or failures and continues to operate as long as at least
one drive in the mirrored set is functioning. With appropriate operating system support, there can be
increased read performance and only a minimal write performance reduction.
RAID 1 requires a minimum number of two hard disk drives.
• RAID 5: block-level striping with distributed parity
RAID 5 uses disk striping and parity data across all drives (distributed parity) to provide high data
throughput, especially for small random access. RAID 5 distributes parity along with the data and requires
all drives but one to be present to operate; drive failure requires replacement, but the array is not
destroyed by a single drive failure. Upon drive failure, any subsequent read operations can be calculated
from the distributed parity so that the drive failure is masked from the end user. The array will have data
loss in the event of a second drive failure and is vulnerable until the data that was on the failing drive is
rebuilt onto a replacement drive. A single drive failure in the set will result in reduced performance of
the entire set until the failing drive has been replaced and rebuilt.
RAID 5 requires a minimum number of three hard disk drives.
• RAID 10: a combination of RAID 0 and RAID 1
RAID 10 consists of striped data across mirrored spans. A RAID 10 drive group is a spanned drive
group that creates a striped set from a series of mirrored drives. RAID 10 allows a maximum of eight
spans. You must use an even number of drives in each RAID virtual drive in the span. The RAID 1
virtual drives must have the same stripe size. RAID 10 provides high data throughput and complete data
redundancy but uses a larger number of spans.
RAID 10 requires a minimum number of four hard disk drives and also requires an even number of drives,
for example, six hard disk drives or eight hard disk drives.
• RAID 50: a combination of RAID 0 and RAID 5
RAID 50 uses distributed parity and disk striping. A RAID 50 drive group is a spanned drive group in
which data is striped across multiple RAID 5 drive groups. RAID 50 works best with data that requires
high reliability, high request rates, high data transfers, and medium-to-large capacity.
Note: Having virtual drives of different RAID levels, such as RAID 0 and RAID 5, in the same drive group is
not allowed. For example, if an existing RAID 5 virtual drive is created out of partial space in an array, the
next virtual drive in the array has to be RAID 5 only.
RAID 50 requires a minimum number of six hard disk drives.
For detailed information about RAID, refer to “Introduction to RAID” in the MegaRAID SAS Software User
Guide on the documentation DVD that comes with your server.
Chapter 5. Configuring the server 57
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring RAID using the ThinkServer EasyStartup program
The ThinkServer EasyStartup program simplifies the process of configuring supported RAID and installing
supported Windows and Linux operating systems and device drivers on your server. The user guide for the
program can be accessed directly from the program interface.
The ThinkServer EasyStartup program has the following features for RAID configuration:
• For use with all supported RAID controllers
• Automatically detects hardware and lists all supported RAID configurations
• Configures one or more disk arrays per controller depending on the number of drives attached to the
controller and the RAID level selected
• Supports hot-spare drives
• Creates a RAID response file that can be used to configure RAID controllers on similarly configured
Lenovo servers
interface of the program.
Some RAID management software also is provided on the ThinkServer EasyStartup DVD to help you manage
RAID arrays and RAID controllers in an operating system environment. After you enter the operating system,
insert the ThinkServer EasyStartup DVD into the optical drive. The installation packages for the programs
are located in the Utilities and Others folder in the root directory of the DVD. The ThinkServer EasyStartup
DVD is designed for different types of servers and the Utilities and Others folder might contain additional
installation packages that are not required to be installed on your server.
Configuring the ThinkServer RAID 300
The ThinkServer RAID 300 (also known as onboard SAS software RAID) is integrated in the PCH on
the system board. If you connect the mini-SAS to mini-SAS signal cables from the system board to the
backplane, you can configure RAID for the hard disk drives using the LSI Software RAID Configuration Utility
program, independently of the operating system. The ThinkServer RAID 300 supports RAID levels 0, 1, and
10 by default. You also can activate RAID 5 by installing a ThinkServer RAID 300 Upgrade Key for Advanced
RAID. See “Installing or removing the ThinkServer RAID 300 Upgrade Key for Advanced RAID” on page 96.
You can install and use the MegaRAID Storage Manager program to manage the RAID array and RAID
controller in an operating system environment.
Before configuring RAID for your server, observe the following precautions:
• Use hard disk drives that are of the same type (SATA or SAS) and have the same capacity within a
single RAID array.
• The total drive capacity of the primary RAID array might be limited to 2 TB.
RAID array status
When you turn on the server, the RAID controller ROM version, the RAID array status, and the list of the
available hard disk drives will be displayed during the POST.
The RAID array status can be one of the following:
• Online
This is the normal status, which indicates that the RAID array is working correctly.
• Degrade
58 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
This status indicates that more than one hard disk drive in the RAID array cannot be synchronized or have
failed. You need to replace the failing hard disk drives and rebuild the data. See “Installing or replacing a
• Offline
This status indicates that the RAID array has failed and cannot be rebuilt. You need to create a new RAID
Starting the LSI Software RAID Configuration Utility program
This topic provides instructions on how to start the LSI Software RAID Configuration Utility program.
To start the LSI Software RAID Configuration Utility program, do the following:
1. Turn on the server.
2. During the POST, when you see the message “Press Ctrl-M or Enter to run LSI Software RAID Setup
Utility,” immediately press Ctrl+M to start the LSI Software RAID Configuration Utility program.
LSI Software RAID Configuration Utility program interface
This topic provides information about the menus and items in the LSI Software RAID Configuration Utility
program. Depending on the version of the program, some menu or item information might differ slightly from
the information in this topic.
When working with the LSI Software RAID Configuration Utility program, you must use the keyboard.
The keys used to perform various tasks are displayed on the bottom of each screen. Use up and down
arrow keys to navigate between items. For most items, the corresponding help message is displayed
on the bottom of the screen when the item is selected. If the item has submenus, you can display the
submenus by pressing Enter.
After entering the LSI Software RAID Configuration Utility program, you can see the Management Menu on
the screen. The Management Menu contains the following menu items:
• Configure
This menu contains items to help you create a RAID array, view the current RAID configuration, add a new
RAID array, delete an existing RAID array, and select a boot virtual drive.
• Initialize
This menu helps you initialize virtual drive(s).
Note: Initializing a virtual drive erases all data on the virtual drive. Back up any data you want to keep and
ensure that the operating system is not installed on the virtual drive before the initialization.
• Objects
This menu helps you configure parameters for the RAID controller, the virtual drive(s), and the physical
drive(s).
• Rebuild
This menu helps you rebuild a physical drive in a RAID array in the event of a physical drive failure.
You can choose to rebuild the data on the failing drive if the drive is still operational. If the drive is not
operational, it must be replaced and the data on the failing drive must be rebuilt on a new drive to restore
the system to fault tolerance.
• Check Consistency
This menu helps you do consistency check for the virtual drive(s). The consistency check verifies the
correctness of the data on virtual drive(s) that use RAID 1, 5, and 10.
Chapter 5. Configuring the server 59
Download from Www.Somanuals.com. All Manuals Search And Download.
The following table shows the various menus and items in the LSI Software RAID Configuration Utility
program. On each menu, press the Enter key to show selectable options and select a desired option by
using up and down arrow keys or type desired values from the keyboard directly.
Table 3. LSI Software RAID Configuration Utility program menu items
Menu item
Submenu item
Easy Configuration
Comments
Configure
Create physical arrays. An array will
automatically become a virtual drive.
New Configuration
Clear the existing configuration and
start a new configuration.
View/Add Configuration
View the existing configuration or add a
new configuration.
Clear Configuration
Select Boot Drive
Varies by configuration.
Adapter
Clear the existing configuration.
Select a boot virtual drive.
Initialize virtual drives.
Initialize
Objects
Set adapter related parameters, such
as rebuild rate, consistency check rate,
auto-rebuild, and so on.
Virtual Drive
Set virtual drive parameters.
Physical Drive
Set physical drive parameters, such as
creating a hot-spare drive for the virtual
drive, making a failing drive as online,
changing a drive state, and viewing the
specifications of a physical drive.
Rebuild
Varies by configuration.
Varies by configuration.
Rebuild physical drive(s).
Check Consistency
Check consistency of virtual drive(s).
Creating, adding, or deleting a RAID array
This topic provides instructions on how to create, add, or delete a RAID array using the LSI Software RAID
Configuration Utility program.
Note: Before you create a RAID array using the LSI Software RAID Configuration Utility program, ensure that
the server meets the required hardware configuration. For example, the server needs to have the required
for information about the required number of hard disk drives for each RAID level. If you want to create a
RAID 5 array using the LSI Software RAID Configuration Utility program, the server also needs to have a
ThinkServer RAID 300 Upgrade Key for Advanced RAID. See “Installing or removing the ThinkServer RAID
To create, add, or delete a RAID array using the LSI Software RAID Configuration Utility program, do the
following:
2. On the main interface of the program, do one of the following depending on your needs:
• If you want to create a RAID array, select Easy Configuration and then follow the instructions on
the screen.
• If you want to add a secondary RAID array (if supported by your server), select View/Add
Configuration and then follow the instructions on the screen to view the current configuration and
add a new RAID array.
60 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you want to delete the existing RAID array, exit the program and back up all your data on the
hard disk drives. After backing up all your data, enter the program main interface and select Clear
Configuration. Select Yes when prompted and follow the instructions on the screen.
Attention: Deleting an existing RAID array erases all data on the array. Ensure that you back up all
data before deleting the RAID array. If the operating system is installed on the RAID array you want to
delete, you need to reinstall the operating system after deleting the RAID array.
• If you want to delete the existing RAID array and create a new RAID array, exit the program and back
up all your data on the hard disk drives. After backing up all your data, enter the program main
interface and select New Configuration. Select Yes when prompted to proceed and then follow the
instructions on the screen.
Attention: Deleting an existing RAID array erases all data on the array. Ensure that you back up all
data before deleting the RAID array. If the operating system is installed on the RAID array you want to
delete, you need to reinstall the operating system after deleting the RAID array.
Initializing a virtual drive
This topic provides instructions on how to initialize a virtual drive using the LSI Software RAID Configuration
Utility program after completing the configuration process.
Virtual drive initialization is the process of writing zeros to the data fields of a virtual drive and, in fault-tolerant
RAID levels, generating the corresponding parity to put the virtual drive in a ready state. Initialization erases
all data on the virtual drive. Drive groups will work without being initialized, but they can fail a consistency
check because the parity fields have not been generated.
Notes:
• Ensure that you back up any data you want to keep before initializing a virtual drive.
• Ensure that the operating system is not installed on the virtual drive you are initializing. Otherwise, you
need to reinstall the operating system after initializing the virtual drive.
To initialize a virtual drive using the LSI Software RAID Configuration Utility program, do the following:
2. On the main interface of the program, select Initialize and follow the instructions on the screen.
Setting a hot-spare drive
This topic provides instructions on how to set a hard disk drive as a hot-spare drive using the LSI Software
RAID Configuration Utility program.
A hot-spare drive is an extra, unused drive that is part of the disk subsystem. It is usually in standby mode
and ready for service if a hard disk drive fails. For detailed information about hot-spare drives, refer to
“Introduction to RAID” in the MegaRAID SAS Software User Guide on the documentation DVD that comes
with your server.
To set a hard disk drive as a hot-spare drive using the LSI Software RAID Configuration Utility program,
do the following:
2. Do one of the following:
• If you want to create or add a new RAID array, you can set a hot-spare drive during the configuration
process by following the instructions on the screen.
Chapter 5. Configuring the server 61
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you want to set a hot-spare drive right after the configuration, select Objects ➙ Physical Drive
from the program main interface. Then, select the hard disk drive that you want to set as a hot-spare
drive and press Enter. A submenu is displayed. Select Make Hot Spare from the submenu and then
select Yes when prompted to set the hard disk drive as a hot-spare drive.
Rebuilding a physical drive
This topic provides instructions on how to rebuild a physical drive using the LSI Software RAID Configuration
Utility program when a physical drive in a RAID array fails.
When a physical drive in a RAID array fails, you can rebuild the drive by recreating the data that was stored
on the drive before it fails. If the drive is not operational, it must be replaced and the data on the failing drive
must be rebuilt on a new drive to restore the system to fault tolerance.
The RAID controller recreates the data using the data stored on other drives in the drive group. Rebuilding
can be done only in drive groups with data redundancy, such as RAID 1, RAID 5, and RAID 10 arrays. For
detailed information about disk rebuild, refer to “Introduction to RAID” in the MegaRAID SAS Software User
Guide on the documentation DVD that comes with your server.
To rebuild a physical drive using the LSI Software RAID Configuration Utility program when a physical drive
in a RAID array fails, do the following:
2. On the main interface of the program, select Rebuild and follow the instructions on the screen.
Note: Run a consistency check immediately after the rebuild completes to ensure data integrity for the virtual
The rebuild rate is the percentage of the computing cycles dedicated to rebuilding failing drives. The rebuild
rate can be configured between 0 percent and 100 percent. At 0 percent, the rebuild is done only if the system
is not doing anything else. At 100 percent, the rebuild has a higher priority than any other system activity.
To configure the rebuild rate using the LSI Software RAID Configuration Utility program, do the following:
Note: Using a rebuild rate of 0 or 100 percent is not recommended. The default value is 30 percent.
2. On the main interface of the program, select Objects ➙ Adapter ➙ Rebuild Rate.
3. Set the rebuild rate by typing a desired value from the keyboard directly.
Running a consistency check
This topic provides instructions on how to run a consistency check for virtual drives using the LSI Software
RAID Configuration Utility program.
The consistency check operation verifies that all stripes on a virtual drive with a redundant RAID level (RAID
1, RAID 5, and RAID 10) are consistent and the date on the virtual drive is correct. For example, in a system
with parity, checking consistency means computing the data on one drive and comparing the results to
the contents of the parity drive.
You should run a consistency check on fault-tolerant virtual drives periodically. It is recommended that you
run a consistency check at least once a month. You must run a consistency check if you suspect that the
virtual drive data might be corrupted. Ensure that you back up the data before running a consistency check
if you suspect that the data might be corrupted.
62 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
To run a consistency check using the LSI Software RAID Configuration Utility program, do the following:
2. On the main interface of the program, select Check Consistency and follow the instructions on the
screen.
The consistency check rate is the rate at which consistency check operations are run on a system. The
consistency check rate can be configured between 0 percent and 100 percent. At 0 percent, the consistency
check is done only if the system is not doing anything else. At 100 percent, the consistency check has a
higher priority than any other system activity.
To configure the consistency check rate using the LSI Software RAID Configuration Utility program, do
the following:
Note: Using a consistency check rate of 0 or 100 percent is not recommended. The default value is 30
percent.
2. On the main interface of the program, select Objects ➙ Adapter ➙ Chk Const Rate.
3. Set the consistency check rate by typing a desired value from the keyboard directly.
Installing and using the MegaRAID Storage Manager program
You can install and use the MegaRAID Storage Manager program to manage the RAID array and RAID
controller in an operating system environment after configuring RAID.
The installation package for the MegaRAID Storage Manager program is on the ThinkServer EasyStartup
DVD. After you enter the operating system, insert the ThinkServer EasyStartup DVD into the optical drive.
The installation package for the MegaRAID Storage Manager program is located in the Utilities and Others
folder in the root directory of the DVD.
To install and use the MegaRAID Storage Manager program, refer to the following chapters in the MegaRAID
SAS Software User Guide on the documentation DVD that comes with your server:
Note: Some information in these chapters might be intended for the advanced SATA/SAS hardware RAID
configurations and might not apply to the ThinkServer RAID 300 configurations.
• “MegaRAID Storage Manager Overview and Installation”
• “MegaRAID Storage Manager Window and Menus”
• “Monitoring System Events and Storage Devices”
• “Maintaining and Managing Storage Configurations”
The MegaRAID SAS Software User Guide also is available on the Lenovo Web site at:
Configuring the advanced SATA/SAS hardware RAID
Before configuring RAID for your server, observe the following precautions:
• Use hard disk drives that are of the same type (SATA or SAS) and have the same capacity within a
single RAID array.
• The total drive capacity of the primary RAID array might be limited to 2 TB.
Chapter 5. Configuring the server 63
Download from Www.Somanuals.com. All Manuals Search And Download.
Some server models come with a RAID card to provide advanced SATA/SAS hardware RAID functions. You
on page 25.
The RAID card provides the WebBIOS Configuration Utility program to help you configure RAID
independently of the operating system. You also can install the MegaRAID Storage Manager program and
the MegaCLI Configuration Utility program to help you manage the RAID array and RAID controller in an
operating system environment.
The installation packages for the MegaRAID Storage Manager program and the MegaCLI Configuration
Utility program are on the ThinkServer EasyStartup DVD. After you enter the operating system, insert the
ThinkServer EasyStartup DVD into the optical drive. The installation packages for the programs are located in
the Utilities and Others folder in the root directory of the DVD.
Note: The ThinkServer EasyStartup DVD is designed for different types of servers and the Utilities and Others
folder might contain additional installation packages that are not required to be installed on your server.
For instructions on how to configure and manage the advanced SATA/SAS hardware RAID, refer to the
MegaRAID SAS Software User Guide on the documentation DVD that comes with your server. This
document also is available on the Lenovo Web site at:
Configuring the Ethernet controllers
The Ethernet controllers are integrated on the system board. They provide an interface for connecting to
a 10 Mbps, 100 Mbps, or 1000 Mbps network and provide full-duplex (FDX) capability, which enables
simultaneous transmission and reception of data on the network.
You do not have to set any jumpers or configure the Ethernet controllers. However, you must install a device
driver to enable the operating system to recognize the controllers.
The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported
operating systems and device drivers on your server. See “Using the ThinkServer EasyStartup program”
on page 53.
The device drivers for onboard Ethernet controllers also are available for download at:
Updating the firmware
The firmware in the server is periodically updated and is available for download on the Lenovo Web site.
Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to check for the latest
level of firmware, such as the BIOS updates and device drivers.
When you replace a device in the server, you might have to either update the server with the latest version of
the firmware that is stored in memory on the device or reflash the BIOS, the TMM firmware, and the FRU/SDR.
Using the Firmware Updater program
The Firmware Updater program enables you to maintain your system firmware up-to-date and helps you
avoid unnecessary outages.
To update your system firmware using the Firmware Updater program, do the following:
64 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Before distributing the firmware updates to a server, ensure that your server can restart successfully
without encountering hardware problems.
Firmware Updater program.
2. Download the ISO image for the Firmware Updater program and the installation instructions in a TXT file.
3. Use any CD or DVD burning software to create a bootable disc with the ISO image.
4. Print the TXT file that contains the installation instructions and follow the instructions to use the Firmware
Updater program to update your system firmware.
Using the Lenovo ThinkServer EasyManage program
The Lenovo ThinkServer EasyManage program enables enterprise users to remotely control and monitor
multiple Lenovo servers within a LAN. The program provides an interface to display all severs being
managed, which enables the administrator to conveniently search for, monitor, and manage servers.
follow the instructions on the Web page.
For detailed information about using the Lenovo ThinkServer EasyManage program, refer to the help system
for the program.
Chapter 5. Configuring the server 65
Download from Www.Somanuals.com. All Manuals Search And Download.
66 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Installing, removing, or replacing hardware
This chapter provides instructions on how to install, remove, or replace hardware for your server.
This chapter contains the following items:
•
•
•
•
For a list of the ThinkServer options, go to:
Guidelines
This topic provides some guidelines that you should read and understand before using your server.
Precautions
Before you use the server, ensure that you read and understand the following precautions:
• Before using the product, be sure to read and understand the multilingual safety instructions and the
Lenovo Limited Warranty (LLW) on the documentation DVD that comes with the product. Reading and
understanding the safety instructions reduces the risk of personal injury and damage to your product.
• When you install your new server, take the opportunity to download and apply the most recent firmware
updates. This step will help to ensure that any known issues are addressed and that your server is
ready to function at maximum levels of performance. To download firmware updates for your server, go
• Before you install optional hardware devices, ensure that the server is working correctly. If the server
troubleshooting. If the problem cannot be solved, see Chapter 8 “Getting information, help, and service”
on page 159.
• Observe good housekeeping in the area where you are working. Put removed covers and other parts
in a safe place.
• If you must turn on the server while the server cover is removed, ensure that no one is near the server
and that no tools or other objects have been left inside the server.
• Do not attempt to lift an object that you think is too heavy for you. If you have to lift a heavy object,
observe the following precautions:
– Ensure that you can stand safely without slipping.
– Distribute the weight of the object equally between your feet.
– Use a slow lifting force. Never move suddenly or twist when you lift a heavy object.
– To avoid straining the muscles in your back, lift by standing or by pushing up with your leg muscles.
• Ensure that you have an adequate number of properly grounded electrical outlets for the server, monitor,
and other devices.
• Back up all important data before you make changes to drives.
• Have a small flat-blade screwdriver available.
© Copyright Lenovo 2012
67
Download from Www.Somanuals.com. All Manuals Search And Download.
• You do not have to turn off the server to install or replace a hot-swap redundant power supply, a
hot-swap hard disk drive, or a hot-plug USB device. However, you must turn off the server before
performing any step that involves installing, removing, or replacing adapter cables or non-hot-swap
devices or components.
• To view the LEDs on the system board and internal components, leave the server connected to power.
• When you are finished working on the server, reinstall all safety shields, guards, labels, and ground wires.
• When working inside the server, you might find some tasks easier if you lay the server on its side.
Handling static-sensitive devices
Attention: Do not open the static-protective package that contains the new part until the defective part has been
removed from the server and you are ready to install the new part. Static electricity, although harmless to you,
can seriously damage server components and parts.
Any server part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
• Use product-specific ESD procedures when they exceed the requirements noted here.
• Ensure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When you handle server parts and components, take these precautions to avoid static-electricity damage:
• Limit your movement. Movement can cause static electricity to build up around you.
• Always carefully handle the parts and other components (such as PCI Express cards, memory modules,
system boards, and microprocessors) by edges or frame. Do not touch solder joints, pins, or exposed
circuitry.
• Do not leave the device where others can handle and possibly damage the device.
• Before you replace a new part, touch the static-protective package containing the new part to an
unpainted metal part of the server for at least two seconds. This reduces static electricity from the
package and your body.
• Remove the new part from the static-protective package and directly install it in the server without
placing it on any other surface. If it is hard for you to do this in your specific situation, place the
static-protective package of the new part on a smooth, level surface, and then place the new part on
the static-protective package.
• Do not place the part on the server cover or other metal surface.
• Take additional care when handling devices during cold weather. Heating reduces indoor humidity
and increases static electricity.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• The use of a grounding system is recommended. For example, it is recommended to wear an electrostatic
discharge (ESD) wrist strap, if one is available. Ensure that you work in an ESD-safe area. Select a
grounding system, such as those listed below, to provide protection that meets the specific service
requirement.
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
68 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the ground prong of the ac plug on ac-operated servers.
System reliability guidelines
To help ensure proper cooling and system reliability, strictly follow these guidelines:
• Each of the drive bays has a drive or a dummy tray installed.
• If the server supports hot-swap redundant power supplies, each of the power supply bay has a redundant
power supply installed, or one bay has a redundant power supply installed while the other bay is covered
by a shield.
• Leave adequate space around the server to ensure that the server cooling system works well. Leave
approximately 50 mm (2 inches) of open space around the front and rear of the server. Do not place
objects in front of the fans. For proper cooling and airflow, install the server cover before you turn on
the server. Operating the server for extended periods of time (more than 30 minutes) with the server
cover removed might damage server components.
• Properly route the cables. For some options, such as PCI Express cards, follow the cabling instructions
that come with the options in addition to the instructions in this manual.
• When replacing a hot-swap drive, install the new hot-swap drive within two minutes of removal.
• If your server has air ducts or air baffles, do not remove them while the server is running. Operating the
server without the air ducts or air baffles might cause the microprocessor(s) to overheat.
• For servers that support up to two microprocessors, ensure that the second microprocessor socket
always contains a microprocessor or is protected by a microprocessor socket cover.
Working inside the server with the power on
Attention: Static electricity that is released to internal server components when the server is turned on might cause
the server to halt, which might result in the loss of data. To avoid this potential problem, always use an ESD wrist strap
or other grounding system when you work inside the server with the power on.
The server supports hot-swap devices and is designed to operate safely while it is turned on and the cover is
removed. Follow these guidelines when you work inside the server with the power on:
• Avoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirts before working inside
the server; do not wear cuff links while you are working inside the server.
• Do not allow your necktie or scarf to hang inside the server.
• Remove jewelry, such as bracelets, necklaces, rings, and loose-fitting wrist watches.
• Remove items from your shirt pocket, such as pens and pencils. These items might fall into the server as
you lean over it.
• Avoid dropping any metallic objects into the server, such as paper clips, hairpins, and screws.
Removing the server cover
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove the server cover.
Chapter 6. Installing, removing, or replacing hardware 69
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
To remove the server cover, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets.
2. Disconnect the power cords, Input/Output (I/O) cables, and all other cables that are connected to
the server.
3. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Press the release button 1 in the direction as shown.
CPU
Mem
PSU
Figure 27. Pressing the release button
70 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Fully open the cover latch 1 and slide the server cover to the rear until it is disengaged from the chassis.
Then, lift the server cover off the chassis and set it aside.
Note: It is recommended that you wait three to five minutes to let the server cool before removing
the server cover.
CPU
Mem
PSU
Figure 28. Removing the server cover
Attention: For proper cooling and airflow, install the server cover before turning on the server. Operating the
server for more than 30 minutes with the server cover removed might damage server components.
To reinstall the server cover, see “Reinstalling the server cover and reconnecting cables” on page 147.
Installing, removing, or replacing hardware
This topic provides instructions on how to install, remove, or replace hardware for your server. You can
expand the capabilities of your server by adding new hardware devices, such as memory modules or other
server options, and maintain your server by replacing the failing hardware devices.
If you are handling a server option, refer to the appropriate installation or removal instructions in this topic
along with the instructions that come with the option.
Notes:
• Use only parts provided by Lenovo.
• Depending on the model, your server might look slightly different from the illustrations in this topic.
The EMI integrity and cooling of the server are protected by having all drive bays and PCI Express card slots
covered or occupied. When you install an internal drive or a PCI Express card, save the EMI shield or dummy
tray from the drive bay or save the PCI Express card slot bracket in the event that you later remove the device.
Attention: An unoccupied drive bay or PCI Express card slot without a cover, shield, dummy tray, filler,
or any other protection might impact the EMI integrity and cooling of the server, which might result in
overheating or component damage.
Removing and reinstalling the rack handles
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
Chapter 6. Installing, removing, or replacing hardware 71
Download from Www.Somanuals.com. All Manuals Search And Download.
This topic provides instructions on how to remove and reinstall the rack handles.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
To remove and reinstall the rack handles, do the following:
1. On each side of the server, remove the screw that secures the rack handle and then remove the rack
handle from the chassis.
PSU
Mem
CPU
Figure 29. Removing the rack handles
72 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
2. To reinstall the rack handles, insert the small tab 1 on the rack handle into the hole 2 in the chassis.
Then, align the screw hole in the rack handle with the corresponding hole in the chassis and install the
screw to secure the rack handle on each side of the server.
PSU
Mem
CPU
Figure 30. Installing the rack handles
Removing and reinstalling the cooling shroud
The cooling shroud must be removed to allow access to most server components. This topic provides
instructions on how to remove and reinstall the cooling shroud.
Removing the cooling shroud
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove the cooling shroud.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
To remove the cooling shroud, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
Chapter 6. Installing, removing, or replacing hardware 73
Download from Www.Somanuals.com. All Manuals Search And Download.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Insert a finger into each of the two holes in the cooling shroud and then lift the cooling shroud out of
the server.
CPU
Mem
PSU
Figure 31. Removing the cooling shroud
Attention: For proper cooling and airflow, reinstall the cooling shroud before turning on the server. Operating
the server for more than 30 minutes with the cooling shroud removed might damage server components.
Reinstalling the cooling shroud
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to reinstall the cooling shroud.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
To reinstall the cooling shroud, do the following:
1. Ensure that all components have been reassembled correctly and that no tools or loose screws are
left inside your server.
2. Ensure that all cables inside the server have been properly routed so that they will not interfere with
installing the cooling shroud.
74 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Note the orientation of the cooling shroud and then place it above the server so that the tabs on both
sides of the cooling shroud are aligned with the corresponding holes or gaps in both sides of the
chassis. Then, lower the cooling shroud into the chassis until it snaps into position.
Note: If necessary, gently press the cooling shroud on both sides so that the tabs on the cooling shroud
completely engage with both sides of the chassis.
CPU
Mem
PSU
Figure 32. Reinstalling the cooling shroud
Installing or removing a memory module
This topic provides instructions on how to install or remove a memory module.
Note: The memory modules are extremely sensitive to ESD. Ensure that you read and understand “Handling
Memory module installation rules
Your server has 12 memory slots and it has the following features:
• Each slot supports 4 GB, 8 GB, and 16 GB 1333 MHz double data rate 3 low-voltage registered dual inline
memory modules (DDR3 LV RDIMMs).
• Each slot supports 4 GB, 8 GB, and 16 GB 1333 MHz DDR3 RDIMMs.
• Each slot supports 2 GB and 4 GB 1333 MHz DDR3 unbuffered dual inline memory modules (UDIMMs)
with Error Checking and Correcting (ECC) technology.
• Your server supports up to six memory modules when one microprocessor is installed and up to 12
memory modules when two microprocessors are installed.
• The minimum system memory for RDIMMs or LV RDIMMs is 4 GB (only one microprocessor installed and
only one 4 GB RDIMM or LV RDIMM installed in the CPU1 DIMMA1 slot).
Chapter 6. Installing, removing, or replacing hardware 75
Download from Www.Somanuals.com. All Manuals Search And Download.
• The minimum system memory for UDIMMs is 2 GB (only one microprocessor installed and only one 2
GB UDIMM installed in the CPU1 DIMMA1 slot).
• The maximum system memory for RDIMMs or LV RDIMMs is 192 GB (two microprocessors installed and
one 16 GB RDIMM or LV RDIMM installed in each of the 12 memory slots).
• The maximum system memory for UDIMMs is 48 GB (two microprocessors installed and one 4 GB
UDIMM installed in each of the 12 memory slots).
For more information about the memory modules in your specific server model, use the Setup Utility
For a list of the supported ThinkServer memory module options, go to:
The following illustration shows the locations of all memory slots on a system board that has two
microprocessors (also known as CPUs) installed.
Figure 33. Memory slots on the system board
1 Memory slot (CPU1 DIMMA1)
2 Memory slot (CPU1 DIMMA2)
3 Memory slot (CPU1 DIMMB1)
4 Memory slot (CPU1 DIMMB2)
5 Memory slot (CPU1 DIMMC1)
6 Memory slot (CPU1 DIMMC2)
7 Memory slot (CPU2 DIMMA1)
8 Memory slot (CPU2 DIMMA2)
9 Memory slot (CPU2 DIMMB1)
10 Memory slot (CPU2 DIMMB2)
11 Memory slot (CPU2 DIMMC1)
12 Memory slot (CPU2 DIMMC2)
76 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
The following table explains the memory module installation rules for servers that have only one
microprocessor (CPU1) installed. The “X” mark indicates the memory slot(s) into which the memory
module(s) should be installed in different situations.
Note: All memory modules to be installed on a server must be the same type (LV RDIMM, RDIMM, or
UDIMM) with the same rank, voltage, and frequency.
Figure 34. CPU1 DIMMs
Table 4. Memory module installation rules for servers with one microprocessor
CPU1 DIMM
One DIMM
A1
X
A2
B1
B2
C1
C2
Two DIMMs
Three DIMMs
Four DIMMs
Six DIMMs
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Chapter 6. Installing, removing, or replacing hardware 77
Download from Www.Somanuals.com. All Manuals Search And Download.
The following table explains the memory module installation rules for servers that have two microprocessors
(CPU1 and CPU2) installed. The “X” mark indicates the memory slot(s) into which the memory module(s)
should be installed in different situations.
Note: All memory modules to be installed on a server must be the same type (LV RDIMM or RDIMM) with
the same rank, voltage, and frequency.
Figure 35. CPU1 DIMMs and CPU2 DIMMs
Table 5. Memory module installation rules for servers with two microprocessors
CPU1 DIMM
CPU2 DIMM
A1
X
A2
B1
B2
C1
C2
A1
X
A2
B1
B2
C1
C2
Two DIMMs
Four DIMMs
Six DIMMs
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Eight DIMMs
Twelve DIMMs
X
X
X
X
X
X
X
X
X
X
X
X
Installing a memory module
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install a memory module.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• To optimize system performance, ensure that you consider and follow the memory module installation
• Use any documentation that comes with the memory module and follow those instructions in addition to
the instructions in this topic.
78 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
To install a memory module, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Locate the memory slots on the system board and read the memory module installation rules. See
6. Disconnect any cables that might prevent your access to the memory slots.
7. Open the retaining clips of the appropriate memory slot.
Figure 36. Opening the retaining clips of the memory slots
8. Touch the static-protective package that contains the new memory module to any unpainted surface on
the outside of the server. Then, take the new memory module out of the package.
Note: Carefully handle the memory module by its edges.
Chapter 6. Installing, removing, or replacing hardware 79
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Position the new memory module over the memory slot. Ensure that the notch 1 on the new memory
module is aligned with the key 2 in the memory slot. Then, press the new memory module straight down
into the memory slot until the retaining clips close and the new memory module snaps into position.
Note: If there is a gap between the memory module and the retaining clips, the memory module has
not been installed correctly. Open the retaining clips, remove the memory module, and then reinstall it
into the memory slot until the retaining clips are completely closed.
Figure 37. Installing a memory module
10. Reconnect any cables that you have disconnected.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Removing a memory module
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove a memory module.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: To optimize system performance, ensure that you consider and follow the memory module installation
To remove a memory module, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Locate the memory slots on the system board and read the memory module installation rules. See
80 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Disconnect any cables that might prevent your access to the memory slots.
7. Locate the memory module that you want to remove and open the retaining clips on both ends of the
memory slot. Then, grasp the memory module by its edges and carefully pull it straight up to remove it
from the memory slot.
Figure 38. Removing a memory module
8. Reconnect any cables that you have disconnected.
9. If you are instructed to return the old memory module, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Installing or removing the Ethernet card
This topic provides instructions on how to install or remove the Ethernet card. If you are installing or
removing any other types of supported PCI Express cards, the procedure is similar.
Note: The Ethernet card is extremely sensitive to ESD. Ensure that you read and understand “Handling
Installing the Ethernet card
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install the Ethernet card.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Use any documentation that comes with the Ethernet card and follow those instructions in addition to
the instructions in this topic.
• Depending on the specific type, the Ethernet card might look different from the illustrations in this topic.
To install the Ethernet card, do the following:
Chapter 6. Installing, removing, or replacing hardware 81
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Remove the riser card assembly 1 and lay it upside down on a flat, clean, and static-protective surface.
Note: Usually an Ethernet card is installed on the riser card assembly 1 and also can be installed in
any PCI Express card slot that supports it. See “Rear view of the server” on page 20 to identify the
PCI Express card slots of your server.
5. Locate the PCI Express card slot for installing the Ethernet card and then remove the PCI Express card
slot bracket from the riser card assembly 1. Store the PCI Express card slot bracket in the event that
you later remove the Ethernet card and need the bracket to cover the place.
Figure 39. Removing a PCI Express card slot bracket
6. Touch the static-protective package that contains the Ethernet card to any unpainted surface on the
outside of the server. Then, take the Ethernet card out of the package.
Note: Carefully handle the Ethernet card by its edges.
82 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Position the Ethernet card near the PCI Express card slot and align the tab of the Ethernet card with
the hole in the riser card assembly 1. Then, press the Ethernet card straight into the slot until it is
securely seated in the slot.
Figure 40. Installing the Ethernet card
8. Depending on the type of the Ethernet card, you might need to connect any required cables. Refer to
the documentation that comes with the Ethernet card for specific information.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation, go to “Completing the parts replacement” on page 147. Then, continue with
the following procedure to install the Ethernet card driver if required.
To install the required device driver for the Ethernet card, do one of the following:
Note: You do not need to use the driver disc that might come with the Ethernet card.
• If you are using a Windows operating system, run the ThinkServer EasyStartup DVD that comes with
your server and follow the instructions on the screen to download and install the required Ethernet
card driver to the server. For more information, see “Using the ThinkServer EasyStartup program on a
• If you are using a Linux operating system, run the ThinkServer EasyStartup DVD that comes with your
server on a computer with a Windows operating system and download the required Ethernet card driver
to a removable storage device. Then, transfer the Ethernet card driver from the removable storage device
to your server and run the driver file to install the driver.
The most up-to-date device drivers for various server models are always available for download on the
Lenovo Support Web site at:
Removing the Ethernet card
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove the Ethernet card.
Chapter 6. Installing, removing, or replacing hardware 83
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Use any documentation that comes with the Ethernet card and follow those instructions in addition to
the instructions in this topic.
• Depending on the specific type, the Ethernet card might look different from the illustration in this topic.
To remove the Ethernet card, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Remove the riser card assembly 1 and lay it upside down on a flat, clean, and static-protective surface.
Note: Usually an Ethernet card is installed on the riser card assembly 1 and also can be installed in
any PCI Express card slot that supports it. See “Rear view of the server” on page 20 to identify the
PCI Express card slots of your server.
5. Locate the Ethernet card on the riser card assembly 1. Depending on the type of the Ethernet card, you
might need to disconnect all cables from the Ethernet card. Then, grasp the Ethernet card by its edges
and carefully pull it out of the riser card assembly 1.
Note: The Ethernet card might fit tightly into the PCI Express card slot. If necessary, alternate moving
each side of the Ethernet card a small and equal amount until it is completely removed from the slot.
Figure 41. Removing the Ethernet card
6. Install a new Ethernet card to replace the old one or install a PCI Express card slot bracket to cover the
8. If you are instructed to return the old Ethernet card, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
84 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing or removing the RAID card
This topic provides instructions on how to install or remove the RAID card.
Some server models come with a required RAID card to provide advanced SATA/SAS hardware RAID
functions to the server. You also can purchase a supported RAID card from Lenovo and install it into the
Note: The RAID card is extremely sensitive to ESD. Ensure that you read and understand “Handling
Installing the RAID card
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install the RAID card.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Use any documentation that comes with the RAID card and follow those instructions in addition to
the instructions in this topic.
• Depending on the specific type, the RAID card and its bracket might look different from the illustrations in
this topic.
• Ensure that you back up your data before installing the RAID card because you might need to reconfigure
RAID and reinstall the operating system after installing the RAID card.
• If you want to install any other PCI Express card your server supports to the riser card assembly 2, refer
to the following installation procedure.
To install the RAID card, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Remove the riser card assembly 2 and lay it upside down on a flat, clean, and static-protective surface.
The procedure is similar to that of the riser card assembly 1. See “Replacing the riser card assembly
Chapter 6. Installing, removing, or replacing hardware 85
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Locate the PCI Express card slot for installing the RAID card and then remove the PCI Express card slot
bracket from the riser card assembly 2. Store the PCI Express card slot bracket in the event that you
later remove the RAID card and need the bracket to cover the place.
Figure 42. Removing a PCI Express card slot bracket
7. Touch the static-protective package that contains the RAID card to any unpainted surface on the outside
of the server. Then, take the RAID card and the low-profile bracket out of the package.
Note: Carefully handle the RAID card by its edges.
8. Remove the two screws that secure the RAID card and then remove the full-height bracket from the
RAID card.
Figure 43. Removing the full-height bracket from the RAID card
86 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Note the orientation of the low-profile bracket and position it on the RAID card. Align the two screw
holes in the low-profile bracket with the corresponding screw holes in the RAID card and then install the
screws to secure the bracket.
Figure 44. Installing the low-profile bracket to the RAID card
10. Position the RAID card near the PCI Express card slot. Ensure that the left edge of the RAID card is
inserted into the notch of the RAID card retention bracket 1 . Then, carefully press the RAID card
straight into the slot until it is securely seated and the low-profile bracket also is secured by the riser
card assembly 2.
Figure 45. Installing the RAID card
11. Connect signal cables to the connectors on the new RAID card and the connectors on the hot-swap
12. Reinstall the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Chapter 6. Installing, removing, or replacing hardware 87
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the RAID card
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove the RAID card. This topic applies only to models that have
a RAID card installed.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Use any documentation that comes with the RAID card and follow those instructions in addition to
the instructions in this topic.
• Depending on the specific type, the RAID card might look different from the illustration in this topic.
• If you remove the RAID card, you will lose the advanced SATA/SAS hardware RAID functions.
• Ensure that you back up your data before removing the RAID card because you might need to reconfigure
RAID and reinstall the operating system after removing the RAID card.
To remove the RAID card, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Remove the riser card assembly 2 and lay it upside down on a flat, clean, and static-protective surface.
The procedure is similar to that of the riser card assembly 1. See “Replacing the riser card assembly
6. Locate the RAID card, which is installed in the PCI Express card slot on the riser card assembly 2.
7. Disconnect all cables from the RAID card and any other related parts.
88 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Grasp the RAID card by its edges and gently slide the RAID card out of the RAID card retention bracket
and the riser card assembly 2.
Note: The RAID card might fit tightly into the PCI Express card slot. If necessary, alternate moving each
side of the RAID card a small and equal amount until it is completely removed from the slot.
Figure 46. Removing the RAID card
9. Depending on your needs, do one of the following:
• Install a new RAID card to replace the old one and reconnect cables. See “Installing the RAID card”
on page 85.
• Install a PCI Express card slot bracket to cover the place and connect related cables to the system
10. Reinstall the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
11. If you are instructed to return the old RAID card, follow all packaging instructions and use any packaging
materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the removal procedure, go to “Completing the parts replacement” on page 147. Then, you
Installing or removing the ThinkServer RAID 500 Upgrade Key for
Advanced RAID
This topic provides instructions on how to install or remove the ThinkServer RAID 500 Upgrade Key for
Advanced RAID (hereinafter referred to as the TR 500 Key).
The TR 500 Key expands the capability of the installed ThinkServer RAID 500 Adapter by activating RAID 5
and RAID 50 levels for advanced SATA/SAS hardware RAID. You can purchase a TR 500 Key from Lenovo.
Installing the TR 500 Key
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
Chapter 6. Installing, removing, or replacing hardware 89
Download from Www.Somanuals.com. All Manuals Search And Download.
This topic provides instructions on how to install the TR 500 Key on a ThinkServer RAID 500 Adapter if your
server has a ThinkServer RAID 500 Adapter installed.
Attention: Back up your data before you begin if you want to reconfigure RAID and reinstall the operating
system after installing the TR 500 Key.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: Use any documentation that comes with the TR 500 Key and follow those instructions in addition to
the instructions in this topic.
To install the TR 500 Key, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Locate the ThinkServer RAID 500 Adapter, which is installed in the PCI Express card slot on the riser
card assembly 2. Then, disconnect any cables from the ThinkServer RAID 500 Adapter.
6. Remove the riser card assembly 2 and lay it upside down on a flat, clean, and static-protective surface.
The procedure is similar to that of the riser card assembly 1. See “Replacing the riser card assembly
7. Touch the static-protective package that contains the TR 500 Key to any unpainted surface on the
outside of the server. Then, take the TR 500 Key out of the package.
Note: Carefully handle the TR 500 Key by its edges.
90 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Locate the TR 500 Key connector on the ThinkServer RAID 500 Adapter and then insert the TR 500 Key
into the connector. You might need to remove the ThinkServer RAID 500 Adapter first, install the TR 500
Key on the ThinkServer RAID 500 Adapter, and then reinstall the ThinkServer RAID 500 Adapter. See
Note: Ensure that the TR 500 Key is securely seated on the ThinkServer RAID 500 Adapter.
Figure 47. Installing the TR 500 Key
10. Reinstall the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation, go to “Completing the parts replacement” on page 147. Then, the hardware
RAID 5 and RAID 50 levels are available for your server if your server has the required number of hard disk
drives installed. Refer to the MegaRAID SAS Software User Guide on the documentation DVD that comes
with your server for information about how to configure the hardware RAID.
Removing the TR 500 Key
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove the TR 500 Key from a ThinkServer RAID 500 Adapter if
your server has a ThinkServer RAID 500 Adapter with a TR 500 Key option installed.
Attention: Back up your data before you begin if you need to reconfigure RAID and reinstall the operating
system after removing the TR 500 Key.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
Chapter 6. Installing, removing, or replacing hardware 91
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you remove the TR 500 Key from the ThinkServer RAID 500 Adapter, the hardware RAID 5 and RAID 50
levels will be disabled.
• Use any documentation that comes with the TR 500 Key and follow those instructions in addition to
the instructions in this topic.
To remove the TR 500 Key, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Locate the ThinkServer RAID 500 Adapter, which is installed in the PCI Express card slot on the riser
card assembly 2. Then, disconnect all cables from the ThinkServer RAID 500 Adapter.
6. Remove the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
7. Locate the TR 500 Key on the ThinkServer RAID 500 Adapter and then remove it from the ThinkServer
RAID 500 Adapter. You might need to remove the ThinkServer RAID 500 Adapter first, remove the TR
500 Key from the ThinkServer RAID 500 Adapter, and then reinstall the ThinkServer RAID 500 Adapter.
Note: Carefully handle the TR 500 Key by its edges.
Figure 48. Removing the TR 500 Key
9. Reinstall the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
10. If you are instructed to return the old TR 500 Key, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
92 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
hardware RAID 5 and 50 levels are not available without the TR 500 Key, you might need to reconfigure
RAID for your server. Refer to the MegaRAID SAS Software User Guide on the documentation DVD that
comes with your server for information about how to configure the hardware RAID.
Installing or removing the ThinkServer RAID 700 Battery
This topic provides instructions on how to install or remove the ThinkServer RAID 700 Battery (also known as
the ThinkServer 9260-8i Battery and hereinafter referred to as the TR 700 Battery).
The TR 700 Battery protects the integrity of the cached data on the ThinkServer RAID 700 Adapter by
providing backup power up to 72 hours in the case of a complete ac power failure or a brief power outage.
It has built-in functionality to automatically charge the battery pack and to communicate battery status
information (such as voltage, temperature, and current) to your server. It also provides an inexpensive
alternative to using an uninterruptible power supply, and a second level of fault tolerance when used in
conjunction with an uninterruptible power supply.
The temperature of the TR 700 Battery is generally 15-20°C (59-68°F) higher than the ambient temperature
during fast charge. Therefore, to complete a recharge cycle, the ambient temperature should be lower
than 55°C (131°F). If the ambient temperature exceeds 55°C (131°F), the recharge cycle will terminate
prematurely, thus preventing the TR 700 Battery from reaching a fully charged state. A recharge cycle lasts
at least six hours under normal operating conditions.
Attention: It is recommended that you replace the TR 700 Battery annually or after 500 recharging cycles,
whichever comes first.
Installing the ThinkServer RAID 700 Battery
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install the TR 700 Battery on a ThinkServer RAID 700 Adapter if
your server has a ThinkServer RAID 700 Adapter installed.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: Use any documentation that comes with the TR 700 Battery and follow those instructions in addition
to the instructions in this topic.
To install the TR 700 Battery, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Locate the ThinkServer RAID 700 Adapter, which is installed in the PCI Express card slot on the riser
card assembly 2. Then, disconnect all cables from the ThinkServer RAID 700 Adapter.
6. Remove the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
7. Remove the ThinkServer RAID 700 Adapter from the riser card assembly 2. See “Installing or removing
Chapter 6. Installing, removing, or replacing hardware 93
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Carefully handle the ThinkServer RAID 700 Adapter by its edges and place it on a flat, clean,
and static-protective surface after you remove it.
8. Touch the static-protective package that contains the TR 700 Battery to any unpainted surface on the
outside of the server. Then, take the TR 700 Battery out of the package.
9. Hold the TR 700 Battery with the battery side up and the board-to-board connector 1 on the bottom
of the TR 700 Battery lining up with the connector 2 on the ThinkServer RAID 700 Adapter. Carefully
install the TR 700 Battery onto the ThinkServer RAID 700 Adapter so that the two connectors are firmly
joined. Then, install the three screws that come with the TR 700 Battery option kit to secure the TR
700 Battery in place.
Notes:
• Center the screwdriver when you install the screws and do not over-tighten the screws to avoid
possible damage to any parts.
• Do not touch the board on the bottom of the TR 700 Battery.
Figure 49. Installing the TR 700 Battery
10. Reinstall the ThinkServer RAID 700 Adapter with the TR 700 Battery to the riser card assembly 2. See
12. Reinstall the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation, go to “Completing the parts replacement” on page 147. Then, configure
Removing the ThinkServer RAID 700 Battery
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove the TR 700 Battery from a ThinkServer RAID 700 Adapter
if your server has a ThinkServer RAID 700 Adapter with a TR 700 Battery installed.
94 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• If you remove the TR 700 Battery, you will lose the backup power for the ThinkServer RAID 700 Adapter.
• Use any documentation that comes with the TR 700 Battery and follow those instructions in addition to
the instructions in this topic.
To remove the TR 700 Battery, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Locate the ThinkServer RAID 700 Adapter, which is installed in the PCI Express card slot on the riser
card assembly 2. Then, disconnect all cables from the ThinkServer RAID 700 Adapter.
6. Remove the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
7. Remove the ThinkServer RAID 700 Adapter from the riser card assembly 2. See “Installing or removing
8. Remove the three screws first. Then, hold the TR 700 Battery and lift it up from the ThinkServer RAID
700 Adapter.
Note: Center the screwdriver when you remove the screws to avoid possible damage to any parts.
Figure 50. Removing the TR 700 Battery
9. Reinstall the ThinkServer RAID 700 Adapter to the riser card assembly 2. See “Installing or removing
11. Reinstall the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See
Chapter 6. Installing, removing, or replacing hardware 95
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Installing or removing the ThinkServer RAID 300 Upgrade Key for
Advanced RAID
This topic provides instructions on how to install or remove the ThinkServer RAID 300 Upgrade Key for
Advanced RAID (hereinafter referred to as the TR 300 Key).
The TR 300 Key expands the capability of the system board by activating RAID 5 for the onboard SAS
software RAID. You can purchase a TR 300 Key from Lenovo.
Installing the TR 300 Key
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install the TR 300 Key.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Use any documentation that comes with the TR 300 Key and follow those instructions in addition to
the instructions in this topic.
• Depending on the model, your server might look slightly different from the illustration in this topic.
To install the TR 300 Key, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Locate the iButton socket on the system board. See “System board components” on page 31. If there is
any PCI Express card installed on the riser card assembly 1, it might block your access to the iButton
socket on the system board. In this case, you need to remove the cooling shroud and then carefully lift
the riser card assembly 1 up so that you can access the iButton socket. You do not need to disconnect
any cables from the PCI Express card or completely remove the riser card assembly 1.
5. Touch the static-protective package that contains the TR 300 Key to any unpainted surface on the
outside of the server. Then, take the TR 300 Key out of the package.
96 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Insert one side of the TR 300 Key under one of the retaining clips on the iButton socket. Then, carefully
press the other side of the TR 300 Key straight down until the key snaps into position and is secured
by the two retaining clips on the iButton socket.
Figure 51. Installing the TR 300 Key
7. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation, go to “Completing the parts replacement” on page 147. Then, the onboard
SAS software RAID 5 is available for your server if your server has the required number of hard disk drives
Removing the TR 300 Key
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
Chapter 6. Installing, removing, or replacing hardware 97
Download from Www.Somanuals.com. All Manuals Search And Download.
This topic provides instructions on how to remove the TR 300 Key if your server has a TR 300 Key installed.
Notes:
• If you remove the TR 300 Key, the onboard SAS software RAID 5 will be disabled.
• Use any documentation that comes with the TR 300 Key and follow those instructions in addition to
the instructions in this topic.
• Depending on the model, your server might look slightly different from the illustration in this topic.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
To remove the TR 300 Key, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Locate the iButton socket on the system board. See “System board components” on page 31. If there is
any PCI Express card installed on the riser card assembly 1, it might block your access to the iButton
socket on the system board. In this case, you need to remove the cooling shroud and then carefully lift
the riser card assembly 1 up so that you can access the iButton socket. You do not need to disconnect
any cables from the PCI Express card or completely remove the riser card assembly 1.
98 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Open the retaining clip 1 on the iButton socket to release the TR 300 Key and then completely remove
the key from the iButton socket.
Figure 52. Removing the TR 300 Key
6. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser
7. If you are instructed to return the old TR 300 Key, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
onboard SAS software RAID 5 is not available without the TR 300 Key, you might need to reconfigure
Chapter 6. Installing, removing, or replacing hardware 99
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing or removing the ThinkServer Management Module Premium
This topic provides instructions on how to install or remove the ThinkServer Management Module Premium
(hereinafter referred to as the TMM Premium).
The TMM Premium offers convenient, remote KVM access and control through the LAN or Internet. You
can use the TMM Premium to gain location-independent remote access to respond to critical incidents and
to undertake necessary maintenance. Therefore, working as an integrated solution in your server, the
TMM Premium provides an increased level of manageability over the basic server management. You can
purchase a TMM Premium from Lenovo.
Installing the TMM Premium
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install the TMM Premium.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Use any documentation that comes with the TMM Premium and follow those instructions in addition to
the instructions in this topic.
• Depending on the model, your server might look slightly different from the illustration in this topic.
To install the TMM Premium, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Touch the static-protective package that contains the TMM Premium to any unpainted surface on the
outside of the server. Then, take the TMM Premium out of the package.
100 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Locate the TMM Premium connector on the system board and then insert the TMM Premium into
the TMM Premium connector.
Note: Ensure that the TMM Premium is securely seated on the system board.
Figure 53. Installing the TMM Premium
What to do next:
• To work with another piece of hardware, go to the appropriate section.
refer to the ThinkServer Management Module User Guide, which is available for download at
Removing the TMM Premium
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove the TMM Premium if the server has one installed.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Chapter 6. Installing, removing, or replacing hardware 101
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
• Use any documentation that comes with the TMM Premium and follow those instructions in addition to
the instructions in this topic.
• If you remove the TMM Premium, the iKVM function for server remote management will be unavailable.
• Depending on the model, your server might look slightly different from the illustration in this topic.
To remove the TMM Premium, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Locate the TMM Premium on the system board and then lift the TMM Premium straight up to remove
it from the connector.
Figure 54. Removing the TMM Premium
5. If you are instructed to return the old TMM Premium, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
102 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Installing or removing the ThinkServer Trusted Platform Module
This topic provides instructions on how to install or remove the ThinkServer Trusted Platform Module
(hereinafter referred to as the TPM).
The TPM is a security chip designed by the Trusted Computing Group (TCG) to provide a hardware method
of data encryption. It stores passwords, encryption keys, and digital certificates to help provide security
solutions and protect the computer. You can purchase a TPM option from Lenovo.
Installing the ThinkServer Trusted Platform Module
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install the TPM.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Use any documentation that comes with the TPM and follow those instructions in addition to the
instructions in this topic.
• Depending on the model, your server might look slightly different from the illustration in this topic.
To install the TPM, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
there is any PCI Express card installed on the riser card assembly 1, it might block your access to the
TPM connector on the system board. In this case, you need to remove the cooling shroud and then
carefully lift the riser card assembly 1 up so that you can access the TPM connector. You do not need to
disconnect any cables from the PCI Express card or completely remove the riser card assembly 1.
5. Touch the static-protective package that contains the TPM to any unpainted surface on the outside of
the server. Then, take the TPM out of the package.
Note: Carefully handle the TPM by its edges.
Chapter 6. Installing, removing, or replacing hardware 103
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Insert the TPM into the TPM connector on the system board.
Figure 55. Installing the TPM
7. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser
What to do next:
• To work with another piece of hardware, go to the appropriate section.
configure the TPM function in the Setup Utility program. See “Configuring the TPM function” on page 50.
Removing the ThinkServer Trusted Platform Module
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to remove the TPM if the server has one installed.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
104 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
• If you remove the TPM, the TPM function will be unavailable.
• Use any documentation that comes with the TPM and follow those instructions in addition to the
instructions in this topic.
• Depending on the model, your server might look slightly different from the illustration in this topic.
To remove the TPM, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Locate the TPM on the system board. See “System board components” on page 31. If there is any PCI
Express card installed on the riser card assembly 1, it might block your access to the TPM connector on
the system board. In this case, you need to remove the cooling shroud and then carefully lift the riser
card assembly 1 up so that you can access the TPM connector. You do not need to disconnect any
cables from the PCI Express card or completely remove the riser card assembly 1.
Chapter 6. Installing, removing, or replacing hardware 105
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the TPM from the TPM connector by lifting it straight up.
Note: Carefully handle the TPM by its edges.
Figure 56. Removing the TPM
6. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser
7. If you are instructed to return the old TPM, follow all packaging instructions and use any packaging
materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Installing or replacing a hot-swap redundant power supply
This topic provides instructions on how to install or replace a hot-swap redundant power supply.
On each hot-swap redundant power supply, there is a status LED near the power cord connector. When the
LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly. When the LED
is lit in amber, it indicates that the hot-swap redundant power supply is likely to fail or has failed.
106 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
The hot-swap redundant power supply adds a second source of power to the server. When the server is
populated with two hot-swap redundant power supplies, it can withstand a power loss from either power
supply. This helps you avoid significant interruption to the operation of the system when a power supply
fails. You can replace a hot-swap redundant power supply without turning off the server.
Note: To maintain the EMI integrity and cooling of the server, install a new hot-swap redundant power
supply as soon as you remove the failing one or cover the other bay with a shield if you just use one module
to provide power.
Some server models come with only one power supply. You can purchase a hot-swap redundant power
supply option from Lenovo.
CAUTION:
Hazardous moving parts. Keep fingers and other body parts away.
CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.
Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components. If you suspect a problem with
one of these parts, contact a service technician.
Installing a hot-swap redundant power supply
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install a hot-swap redundant power supply.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Your hot-swap redundant power supply might look slightly different from the illustrations in this topic.
• Use any documentation that comes with the new hot-swap redundant power supply and follow those
instructions in addition to the instructions in this topic.
To install a hot-swap redundant power supply, do the following:
Chapter 6. Installing, removing, or replacing hardware 107
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Locate the bay for the power supply in the rear of your server. Insert a finger into the hole in the metal
shield that protects the bay, press the tab 1 in the direction as shown, and then pull the shield out of
the chassis. Store the shield in the event that you later remove the power supply and need the shield
to cover the bay.
Figure 57. Removing the protective shield for the power supply bay
2. Touch the static-protective package that contains the new hot-swap redundant power supply to any
unpainted surface on the outside of the server. Then, take the new hot-swap redundant power supply
out of the package.
108 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Note the orientation of the new hot-swap redundant power supply and then slide it into the chassis until
it snaps into position.
Figure 58. Installing a hot-swap redundant power supply
4. Connect the power cord to the power connector on the new hot-swap redundant power supply. Then,
check the status LED near the power connector. When the LED is lit in green, it indicates that the
hot-swap redundant power supply is working correctly. When the LED is lit in amber, it indicates that the
hot-swap redundant power supply is likely to fail or has failed. Reinstall the new hot-swap redundant
power supply to see if the problem can be solved. If the new hot-swap redundant power supply still
does not work correctly, contact your place of purchase or a service representative for help.
Replacing a hot-swap redundant power supply
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to replace a hot-swap redundant power supply.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Your hot-swap redundant power supply might look slightly different from the illustrations in this topic.
• Use any documentation that comes with the hot-swap redundant power supply and follow those
instructions in addition to the instructions in this topic.
Chapter 6. Installing, removing, or replacing hardware 109
Download from Www.Somanuals.com. All Manuals Search And Download.
To replace a hot-swap redundant power supply, do the following:
1. Locate the failing hot-swap redundant power supply in the rear of your server. Then, disconnect the
power cord from the failing hot-swap redundant power supply.
2. Press the tab 1 in the direction as shown and carefully pull the handle 2 at the same time to slide the
failing hot-swap redundant power supply out of the chassis.
Note: Do not use too much force. You can first carefully slide the hot-swap redundant power supply a
little bit out to release it from the secured position. Then, completely slide it out of the chassis.
Figure 59. Removing a hot-swap redundant power supply
4. If you are instructed to return the old hot-swap redundant power supply, follow all packaging instructions
and use any packaging materials that are supplied to you for shipping.
Installing or replacing a heat sink
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install or replace a heat sink.
110 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION:
The heat sink might be very hot. Turn off the server and wait three to five minutes to let the server
cool before removing the server cover.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Use any documentation that comes with the heat sink and follow those instructions in addition to the
instructions in this topic.
• Depending on the model, your server might look slightly different from the illustrations in this topic.
To install or replace a heat sink, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Locate the heat sink or the place for installing the second heat sink. See “Server components” on
page 22.
Chapter 6. Installing, removing, or replacing hardware 111
Download from Www.Somanuals.com. All Manuals Search And Download.
6. If you are replacing a heat sink, remove the four screws that secure the heat sink to the system board. It
is recommended that you carefully remove the four screws from the system board using the following
method to avoid any possible damage to the system board.
a. Partially remove screw 1 , then completely remove screw 3 , and then return to screw 1 and
completely remove it.
b. Partially remove screw 2 , then completely remove screw 4 , and then return to screw 2 and
completely remove it.
Note: The four screws are integrated parts of the heat sink. Do not try to remove the four screws
from the heat sink.
Figure 60. Removing the screws that secure the heat sink
7. Gently twist the heat sink to free it from the microprocessor and then lift the heat sink off the system
board.
8. Lay aside the old heat sink. Touch the static-protective package that contains the new heat sink to any
unpainted surface on the outside of the server. Then, take the new heat sink out of the package.
Notes:
• If you are replacing a heat sink, you need to use a cleaning pad that might come with the new heat
sink to wipe the thermal grease from the top of the microprocessor before installing the new heat
sink. Dispose of the cleaning pad after all of the thermal grease is removed from the microprocessor.
• When handling the new heat sink, do not touch the thermal grease on the bottom of it.
9. Remove any protective cover that protects the thermal grease on the bottom of the new heat sink. Then,
place the new heat sink on the system board so that the four screws on the new heat sink are aligned
with the corresponding mounting studs on the system board.
112 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Install the four screws to secure the new heat sink on the system board. It is recommended that you
carefully install the four screws using the following method to avoid any possible damage to the system
board.
a. Partially tighten screw 1 , then firmly tighten screw 3 , and then return to screw 1 and firmly tighten
it. Do not over-tighten the screws.
b. Partially tighten screw 2 , then firmly tighten screw 4 , and then return to screw 2 and firmly tighten
it. Do not over-tighten the screws.
Figure 61. Installing the screws to secure the heat sink
11. If you are instructed to return the old heat sink, follow all packaging instructions and use any packaging
materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.
Installing or replacing the microprocessor
This topic provides instructions on how to install or replace the microprocessor.
Installing the second microprocessor
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install the second microprocessor.
Chapter 6. Installing, removing, or replacing hardware 113
Download from Www.Somanuals.com. All Manuals Search And Download.
Depending on the model, your server might come with one or two microprocessors. For server models with
one microprocessor, the microprocessor is installed in the microprocessor socket 1 and the microprocessor
socket 2 is protected by a plastic socket cover. You can purchase a microprocessor option kit from Lenovo
and install the second microprocessor to expand system capabilities.
CAUTION:
Turn off the server and wait three to five minutes to let the server cool before removing the server
cover.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Ensure that you install the correct type of microprocessor option your server supports. See “Memory
module installation rules” on page 75. When two microprocessors are installed, both must have the same
core voltage and core speed.
• Use any documentation that comes with the microprocessor option kit and follow those instructions in
addition to the instructions in this topic.
• Your microprocessor, socket, and socket cover might look slightly different from the illustrations in this
topic.
To install the second microprocessor, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Locate the microprocessor socket 2 on the system board. See “System board components” on page 31.
114 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press down the small handle on the microprocessor socket and then pull the handle a little bit outward
to release it from the secured position. Then, gently press the microprocessor retainer to open it. Ensure
that the small handle and the microprocessor retainer are in the fully open position.
Figure 62. Opening the handle and microprocessor retainer
7. Touch the static-protective package that contains the new microprocessor to any unpainted surface on
the outside of the server. Then, remove the new microprocessor from the package.
Chapter 6. Installing, removing, or replacing hardware 115
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Remove the plastic microprocessor socket cover. Store the microprocessor socket cover in the
event that you later remove the microprocessor and need the socket cover to protect the pins on
the socket. Then, remove the protective cover that protects the gold contacts on the bottom of the
new microprocessor.
Figure 63. Removing the microprocessor socket cover
Notes:
• Do not remove the socket cover until you install a microprocessor into the socket. If you remove the
microprocessor, install the socket cover or a new microprocessor immediately.
• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be
kept as clean as possible.
• Do not touch the pins on the microprocessor socket and the gold contacts on the bottom of the
new microprocessor.
Figure 64. Do not touch the pins
116 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align
the notches 1 on it with the tabs 2 in the microprocessor socket. Then, carefully lower the new
microprocessor straight down into the microprocessor socket.
Note: The small triangle 3 on one corner of the new microprocessor is the microprocessor orientation
indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled
corner 4 of the microprocessor socket.
Figure 65. Installing the microprocessor
Chapter 6. Installing, removing, or replacing hardware 117
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Gently close the microprocessor retainer, press down the small handle, and then push the handle inward
to lock the retainer into position and secure the new microprocessor in the socket.
Figure 66. Securing the microprocessor in the socket
11. Install the new heat sink that comes with the microprocessor option kit. See “Installing or replacing a
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Replacing the microprocessor
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to replace the microprocessor.
CAUTION:
The heat sink and microprocessor might be very hot. Turn off the server and wait three to five minutes
to let the server cool before removing the server cover.
118 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
installation rules” on page 75. When two microprocessors are installed, both must have the same core
voltage and core speed.
• Use any documentation that comes with the microprocessor option kit and follow those instructions in
addition to the instructions in this topic.
• Your microprocessor, socket, and socket cover might look slightly different from the illustrations in this
topic.
To replace the microprocessor, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
Chapter 6. Installing, removing, or replacing hardware 119
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Locate the microprocessor socket, press down the small handle on the microprocessor socket, and
then pull the handle a little bit outward to release it from the secured position. Then, gently press
the microprocessor retainer to open it. Ensure that the small handle and the microprocessor retainer
are in the fully open position.
Figure 67. Opening the handle and microprocessor retainer
7. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor
socket. Place the old microprocessor on a static-protective surface.
Notes:
• Do not touch the gold contacts on the bottom of the microprocessor.
• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be
kept as clean as possible.
Figure 68. Removing the microprocessor
120 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Touch the static-protective package that contains the new microprocessor to any unpainted surface on
the outside of the server. Then, remove the new microprocessor from the package.
9. Remove the protective cover that protects the gold contacts on the bottom of the new microprocessor.
Do not touch the pins on the microprocessor socket and the gold contacts on the bottom of the new
microprocessor.
Figure 69. Do not touch the pins
10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align
the notches 1 on it with the tabs 2 in the microprocessor socket. Then, carefully lower the new
microprocessor straight down into the microprocessor socket.
Note: The small triangle 3 on one corner of the new microprocessor is the microprocessor orientation
indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled
corner 4 of the microprocessor socket.
Figure 70. Installing the microprocessor
Chapter 6. Installing, removing, or replacing hardware 121
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Gently close the microprocessor retainer, press down the small handle, and then push the handle inward
to lock the retainer into position and secure the new microprocessor in the socket.
Figure 71. Securing the microprocessor in the socket
13. If you are instructed to return the old microprocessor, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Installing or replacing a hot-swap hard disk drive
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install or replace a hot-swap hard disk drive.
For a list of the ThinkServer hard disk drive options, go to:
You can install or replace a failing hot-swap hard disk drive without turning off the server, which helps you
avoid significant interruption to the operation of the system.
122 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. The
number of the installed hard disk drives in your server varies depending on the server model. The vacant
bays are occupied by dummy hard disk drive trays. When you install a hot-swap hard disk drive, save the
removed dummy hard disk drive tray from the drive bay in the event that you later remove the hot-swap hard
disk drive and need the dummy tray to cover the place.
Attention: An unoccupied drive bay without any other protection might impact the EMI integrity and cooling
of the server, which might result in overheating or component damage. To maintain the EMI integrity and
cooling of the server, install a new hot-swap hard disk drive as soon as you remove the failing one or
the dummy tray.
Before you begin, review the following hard disk drive installation rules:
• Follow the order of the hard disk drive bays when installing a hard disk drive. See “Server components”
on page 22 to locate the hard disk drive bays in your server.
• For RAID configuration, the hard disk drives must be the same type with the same capacity if they are
• For hard disk drives with different capacities, install the hard disk drive by following the order of the hard
disk drive bays as well as the order from the lowest capacity to the highest capacity.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Depending on the model, your server might come with 3.5-inch hot-swap hard disk drives or 2.5-inch
hot-swap hard disk drives. The illustrations in this topic are based on server models with 3.5-inch
hot-swap hard disk drives. For other models, the replacement procedure is similar.
• Depending on the model, your server might look slightly different from the illustrations in this topic.
• Use any documentation that comes with the hot-swap hard disk drive and follow those instructions in
addition to the instructions in this topic.
To install or replace a hot-swap hard disk drive, do the following:
Chapter 6. Installing, removing, or replacing hardware 123
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press the release button 1 to open the handle of the hot-swap hard disk drive or the dummy tray.
PSU
Mem
CPU
Figure 72. Opening the handle of the hot-swap hard disk drive
Figure 73. Opening the handle of the dummy hot-swap hard disk drive tray
124 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Pull the handle and carefully slide the hot-swap hard disk drive or the dummy tray out of the front of
the chassis.
PSU
Mem
CPU
Figure 74. Removing the hot-swap hard disk drive
Figure 75. Removing the dummy hot-swap hard disk drive tray
4. Touch the static-protective package that contains the new hot-swap hard disk drive to any unpainted
surface on the outside of the server. Then, take the new hot-swap hard disk drive out of the package.
Note: Do not touch the circuit board on the hard disk drive.
Chapter 6. Installing, removing, or replacing hardware 125
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Slide the new hot-swap hard disk drive into the drive bay from the front until it snaps into position
and then completely close the handle.
PSU
Mem
CPU
Figure 76. Installing the hot-swap hard disk drive
6. Check the hot-swap hard disk drive status LEDs to ensure that the hard disk drive is operating correctly.
You might have to restart the server for the newly installed hard disk drive to be recognized. See
“Hot-swap hard disk drive status LEDs” on page 25. If the hard disk drive is faulty, you need to reinstall
or replace it until it is operating correctly.
7. Do one of the following:
• If you are installing a hot-swap hard disk drive, save the removed dummy hard disk drive tray in
the event that you later remove the hot-swap hard disk drive and need a dummy tray to cover the
drive bay.
• If you are replacing a failing hot-swap hard disk drive and are instructed to return the failing hot-swap
hard disk drive, follow all packaging instructions and use any packaging materials that are supplied to
you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Installing or replacing the optical drive
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install or replace the optical drive.
126 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
This topic contains the following items:
Installing or replacing the optical drive for server models with 3.5-inch hard disk
drives
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to install or replace the optical drive for server models with 3.5-inch
hard disk drives.
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are
installed, note the following:
• Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
• Use of controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Depending on the model, your server might look slightly different from the illustrations in this topic.
• Use any documentation that comes with the new optical drive and follow those instructions in addition to
the instructions in this topic.
• If no optical drive is installed on your server, there is a dummy optical drive.
To install or replace the optical drive for server models with 3.5-inch hard disk drives, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Do one of the following:
Chapter 6. Installing, removing, or replacing hardware 127
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of
the optical drive. Press the rear of the retaining bracket 1 in the direction as shown and push the
optical drive from the rear until it is projected from the front of the chassis. Then, hold the optical
drive from the front and completely slide it out of the chassis.
PSU
Mem
CPU
Figure 77. Removing the optical drive for server models with 3.5-inch hard disk drives
• If you are installing an optical drive, remove the dummy optical drive tray. The way of removing the
dummy optical drive tray is similar to the way of removing the optical drive that is described above.
Store the dummy optical drive tray in the event that you later remove the optical drive and need the
dummy optical drive tray to cover the place.
6. Touch the static-protective package that contains the new optical drive to any unpainted surface on the
outside of the server. Then, take the new optical drive out of the package.
7. Remove the retaining bracket from the old optical drive or the dummy optical drive tray. Then, install it
on the side of the new optical drive.
Figure 78. Installing the optical drive retaining bracket
128 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Slide the new optical drive with the retaining bracket into the drive bay from the front until it snaps
into position.
PSU
Mem
CPU
Figure 79. Installing the optical drive for server models with 3.5-inch hard disk drives
9. Connect the signal cable 1 and the power cable 2 to the rear of the new optical drive.
Figure 80. Connecting cables to the rear of the optical drive
10. If necessary, connect the other end of the signal cable to the SATA connector 0 on the system board
11. If you are instructed to return the old optical drive, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.
Installing or replacing the optical drive for server models with 2.5-inch hard disk
drives
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
Chapter 6. Installing, removing, or replacing hardware 129
Download from Www.Somanuals.com. All Manuals Search And Download.
This topic provides instructions on how to install or replace the optical drive for server models with 2.5-inch
hard disk drives.
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are
installed, note the following:
• Do not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
• Use of controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Depending on the model, your server might look slightly different from the illustrations in this topic.
• Use any documentation that comes with the new optical drive and follow those instructions in addition to
the instructions in this topic.
• If no optical drive is installed on your server, there is a dummy optical drive.
To install or replace the optical drive for server models with 2.5-inch hard disk drives, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Do one of the following:
130 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you are replacing an optical drive, disconnect the signal cable from the system board and
disconnect the power cable from the backplane. Press the rear of the retaining bracket 1 in the
direction as shown and push the optical drive from the rear until it is projected from the front of the
chassis. Then, hold the optical drive from the front and completely slide it out of the chassis.
CPU
Mem
Figure 81. Removing the optical drive for server models with 2.5-inch hard disk drives
• If you are installing an optical drive, remove the dummy optical drive tray. The way of removing the
dummy optical drive tray is similar to the way of removing the optical drive that is described above.
Store the dummy optical drive tray in the event that you later remove the optical drive and need the
dummy optical drive tray to cover the place.
6. Touch the static-protective package that contains the new optical drive to any unpainted surface on the
outside of the server. Then, take the new optical drive out of the package.
7. Remove the retaining bracket from the old optical drive or the dummy optical drive tray. Then, install it
on the side of the new optical drive.
Figure 82. Installing the optical drive retaining bracket
Chapter 6. Installing, removing, or replacing hardware 131
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Connect the signal cable 1 and the power cable 2 to the rear of the new optical drive.
Figure 83. Connecting cables to the rear of the optical drive
9. Slide the new optical drive with the retaining bracket and cables into the drive bay from the front until
it snaps into position.
Figure 84. Installing the optical drive for server models with 2.5-inch hard disk drives
10. Connect the other end of the signal cable to the SATA connector 0 on the system board and connect the
other end of the power cable to the backplane. See “Reinstalling the server cover and reconnecting
11. If you are instructed to return the old optical drive, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.
Replacing the hot-swap hard disk drive backplane
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
132 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
This topic provides instructions on how to replace the hot-swap hard disk drive backplane.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• The hot-swap hard disk drive backplane is sensitive to ESD. Ensure that you read and understand
• Depending on the model, your server might look slightly different from the illustrations in this topic.
• The illustrations in the following procedure show the backplane for 3.5-inch hard disk drives. For the
backplane for 2.5-inch hard disk drives, the replacement procedure is similar.
• In the following illustrations, system fans are removed in order to make the hot-swap hard disk drive
backplane clearly visible.
To replace the hot-swap hard disk drive backplane, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
4. Locate the hot-swap hard disk drive backplane. See “Hot-swap hard disk drive backplane” on page 27.
5. Remove all the installed hot-swap hard disk drives and dummy trays (if any) from the hard disk drive
6. Note down the cable connections on the backplane and then disconnect all cables from the backplane.
Chapter 6. Installing, removing, or replacing hardware 133
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Press the two retaining latches in the direction as shown to release the backplane.
Figure 85. Releasing the backplane
134 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Carefully lift up the backplane. When the hooks 1 on the chassis are aligned with the corresponding
holes in the backplane, slowly move the backplane a little bit outward. Then, completely remove the
backplane.
Figure 86. Removing the backplane
9. Touch the static-protective package that contains the new hot-swap hard disk drive backplane to any
unpainted surface on the outside of the server. Then, remove the new backplane from the package.
Note: Carefully handle the backplane by its edges.
Chapter 6. Installing, removing, or replacing hardware 135
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Note the orientation of the new backplane and position it on the chassis so that the hooks 1 on the
chassis pass through the corresponding holes in the new backplane. Then, carefully press the new
backplane straight down until it is secured in place by the small retaining studs on the chassis.
Figure 87. Installing the backplane
136 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Press the two retaining latches as shown. Then, the backplane is secured in place.
Figure 88. Securing the backplane
12. Reinstall all the hot-swap hard disk drives and dummy trays (if any) in the hard disk drive bays. See
13. Refer to your note to connect the cables to the new backplane.
14. If you are instructed to return the old hot-swap hard disk drive backplane, follow all packaging
instructions and use any packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Replacing the Intelligent Diagnostics Module
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to replace the Intelligent Diagnostics Module (hereinafter referred to
as the IDM).
The IDM provides diagnostic LEDs through the IDM panel to help you easily identify a problem. For more
Chapter 6. Installing, removing, or replacing hardware 137
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Depending on the model, your server might look slightly different from the illustrations in this topic.
• If you remove the IDM, the server will lose the diagnostic LEDs on the IDM panel.
To replace the IDM, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Disconnect the cable from the rear of the IDM.
6. Remove the two screws that secure the IDM and then carefully remove the IDM from the chassis.
PSU
Mem
CPU
Figure 89. Removing the IDM
7. Touch the static-protective package that contains the new IDM to any unpainted surface on the outside
of the server. Then, take the new IDM out of the package.
138 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Position the new IDM on the chassis so that the screw holes in the new IDM are aligned with the
corresponding mounting studs on the chassis. Then, install the screws to secure the new IDM in place.
PSU
Mem
CPU
Figure 90. Installing the IDM
9. Connect the IDM cable to the rear of the new IDM.
10. If you are instructed to return the old IDM, follow all packaging instructions and use any packaging
materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Replacing a system fan
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to replace a system fan.
CAUTION:
Hazardous moving parts. Keep fingers and other body parts away.
Chapter 6. Installing, removing, or replacing hardware 139
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
To replace a system fan, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Reconnect the power cord to the server and the electrical outlet.
6. Locate the failing system fan. The system fan error LED on the system board is lit. See “System board
7. Disconnect the power cord from the electrical outlet.
8. Disconnect the cable of the system fan from the system fan connector on the system board. See
9. Lift up the tape of the system fan to remove the system fan out of the chassis.
Figure 91. Removing the system fan
10. Touch the static-protective package that contains the new system fan to any unpainted surface on the
outside of the server. Then, remove the new system fan from the package.
140 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Note the orientation of the new system fan and then insert the new system fan into the chassis until
it snaps into position.
Note: Install a new system fan as soon as you remove the failing one.
Figure 92. Installing the system fan
12. Press down the tape of the new system fan and then connect the cable of the new system fan to
the system fan connector on the system board.
13. If you are instructed to return the old system fan, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Replacing the front panel board
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to replace the front panel board.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Depending on the model, your server might look slightly different from the illustrations in this topic.
• The front panel board is extremely sensitive to ESD. Ensure that you read and understand “Handling
Chapter 6. Installing, removing, or replacing hardware 141
Download from Www.Somanuals.com. All Manuals Search And Download.
To replace the front panel board, do the following:
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
5. Disconnect the front panel cable and the front panel USB cable from the rear of the front panel board.
6. Remove the two screws that secure the front panel board and then carefully remove the front panel
board from the chassis.
PSU
Mem
CPU
Figure 93. Removing the front panel board
7. Touch the static-protective package that contains the new front panel board to any unpainted surface
on the outside of the server. Then, take the new front panel board out of the package.
Note: Carefully handle the front panel board by its edges.
142 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Carefully position the new front panel board on the chassis so that the front controls, connectors,
and LEDs are through the corresponding holes in the front bezel and the two screw holes in the new
front panel board are aligned with the corresponding mounting studs on the chassis. Then, install the
screws to secure the front panel board in place.
PSU
Mem
CPU
Figure 94. Installing the front panel board
9. Connect the front panel cable and the front panel USB cable to the rear of the new front panel board.
10. If you are instructed to return the old front panel board, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Replacing the riser card assembly 1
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to replace the riser card assembly 1.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Notes:
• Depending on the model, your server might look slightly different from the illustrations in this topic.
• Use any documentation that comes with the new riser card assembly 1 and follow those instructions in
addition to the instructions in this topic.
To replace the riser card assembly 1, do the following:
Chapter 6. Installing, removing, or replacing hardware 143
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
6. Grasp the riser card assembly 1 by its edges and carefully lift it straight up and off the chassis.
Figure 95. Lifting the riser card assembly 1 off the chassis
7. If there is any PCI Express card (such as an Ethernet card) installed on the riser card assembly 1, note
down the cable connections, disconnect all cables from the card, and then completely remove the riser
card assembly 1 out of the chassis. Then, remove the PCI Express card from the riser card assembly 1.
8. Touch the static-protective package that contains the new riser card assembly 1 to any unpainted
surface on the outside of the server. Then, take the new riser card assembly 1 out of the package.
144 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Position the new riser card assembly 1 on the chassis and align it with the riser card assembly 1 slot on
the system board and align the rear of it with the corresponding rail guides in the rear of the chassis.
Then, press the new riser card assembly 1 straight down until it is securely seated in the slot.
Note: If there is any PCI Express card (such as an Ethernet card) installed on the riser card assembly 1,
install the PCI Express card to the new riser card assembly 1 first. See “Installing the Ethernet card” on
page 81. Then, refer to your note to reconnect any cables to the PCI Express card on the new riser
card assembly 1 and properly route all the cables.
Figure 96. Installing the riser card assembly 1
10. If you are instructed to return the old riser card assembly, follow all packaging instructions and use any
packaging materials that are supplied to you for shipping.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
Replacing the system board battery
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to replace the system board battery.
Chapter 6. Installing, removing, or replacing hardware 145
Download from Www.Somanuals.com. All Manuals Search And Download.
Your server has a special type of memory that maintains the date, time, and configuration information for
built-in features. The system board battery keeps the information active when you turn off the server. The
system board battery normally requires no charging or maintenance throughout its life; however, no battery
lasts forever. If the system board battery fails, the date, time, and configuration information, including
passwords, are lost and an error message is displayed when you turn on the server.
DANGER
Danger of explosion if battery is incorrectly replaced.
When replacing the lithium coin cell battery, use only the same or an equivalent type that is
recommended by the manufacturer. The battery contains lithium and can explode if not properly
used, handled, or disposed of.
Do not:
• Throw or immerse into water
• Heat to more than 100°C (212°F)
• Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
The following statement applies to users in the state of California, U.S.A.
California Perchlorate Information:
Products containing CR (manganese dioxide) lithium coin cell batteries may contain perchlorate.
Perchlorate Material - special handling may apply, See
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
To replace the system board battery, do the following:
Note: After you replace the system board battery, you must reset passwords, reset system date and time,
and reconfigure the server.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all
power cords from electrical outlets and disconnect all cables that are connected to the server.
2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,
clean, and static-protective surface. See the Rack Installation Instructions that comes with the server.
Note: If there is any PCI Express card installed on the riser card assembly 1, it might block your access
to the system board battery. In this case, you need to remove the cooling shroud and then carefully
lift the riser card assembly 1 up so that you can access the system board battery. You do not need to
disconnect any cables from the riser card assembly 1 or completely remove the riser card assembly 1.
146 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the old system board battery.
Figure 97. Removing the system board battery
6. Install a new system board battery.
Figure 98. Installing the system board battery
7. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser
8. Dispose of the old system board battery as required by local ordinances or regulations.
What to do next:
• To work with another piece of hardware, go to the appropriate section.
• To complete the replacement, go to “Completing the parts replacement” on page 147. After you replace
the system board battery, you must reset passwords, reset system date and time, and reconfigure the
Completing the parts replacement
This topic provides instructions to help you complete the parts replacement and turn on your server.
To complete the parts replacement, you must properly route the cables inside the server, reinstall the cooling
shroud (if necessary), reinstall the server cover, reconnect all the external cables and, for some devices,
update the firmware and run the Setup Utility program to do further setup.
Reinstalling the server cover and reconnecting cables
Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”
This topic provides instructions on how to reinstall the server cover and reconnect cables to your server.
Attention: For proper cooling and airflow, reinstall the server cover before turning on the server. Operating
the server for extended periods of time (more than 30 minutes) with the server cover removed might
damage server components.
Chapter 6. Installing, removing, or replacing hardware 147
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.
Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
To reinstall the server cover and reconnect cables to your server, do the following:
1. Ensure that all components have been reassembled correctly and that no tools or loose screws are
left inside your server.
2. Ensure that all internal cables are routed correctly and secured by any cable clips or ties in the server.
Keep cables clear of the hinges and sides of the server chassis to avoid interference with reinstalling
the cooling shroud and the server cover. The following illustrations show the cable routing for the two
chassis configurations based on the supported hard disk drives.
• Route the signal cables 1 through the left inner side of the chassis. The signal cables include the
mini-SAS to mini-SAS signal cable, the front panel cable, the front panel USB cable, the diagnostic
module cable, and the SATA signal cable for the optical drive.
• Connect the power cable 2 for the optical drive to the optical drive power connector on the
backplane and properly route the cable in the chassis.
• Route the backplane power cable 3 through the right inner side of the chassis.
Figure 99. Cable routing for server models with 3.5-inch hard disk drives
148 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 100. Cable routing for server models with 2.5-inch hard disk drives
3. If the cooling shroud is removed, reinstall the cooling shroud. See “Removing and reinstalling the
Chapter 6. Installing, removing, or replacing hardware 149
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Ensure that the cover latch is in the open position. Place the server cover above the chassis so that
the cover latch is aligned with the cover latch slot in the chassis. Then, lower the server cover onto
the chassis until the cover latch is inserted into its slot and both sides of the server cover engage the
guides on both sides of the chassis.
CPU
Mem
PSU
Figure 101. Installing the server cover
5. Pivot the cover latch to the closed position and slide the server cover to the front of the chassis at the
same time until the server cover snaps into position and the cover latch is completely closed.
CPU
Mem
PSU
Figure 102. Closing the server cover completely
6. If the server is installed in a rack cabinet, reinstall the server into the rack cabinet. See the Rack
Installation Instructions that comes with the server.
150 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Reconnect external cables and power cord(s) to the server. See “Rear view of the server” on page 20 to
identify the connectors on the rear panel of the server.
Attention: To avoid component damage, connect the power cord(s) last.
Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will
come with the CRU or will come a few days after the CRU arrives.
Updating the server configuration
When you turn on the server for the first time after you install, remove, or replace a device, you might
need to update the server configuration.
Some optional devices have device drivers that you must install. For information about installing device
drivers, use the documentation that comes with each optional device. To obtain the supported device drivers
for your server from the Lenovo Support Web site, go to http://www.lenovo.com/drivers, and then follow the
instructions on the Web page to find and download the device drivers you need.
Refer to the following information resources to update the server configuration:
page 53.
Chapter 6. Installing, removing, or replacing hardware 151
Download from Www.Somanuals.com. All Manuals Search And Download.
152 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Troubleshooting and diagnostics
This chapter provides information about basic troubleshooting and diagnostic methods to help you solve
problems that might occur in the server.
If you cannot diagnose and correct a problem by using the information in this chapter, see Chapter 8
Troubleshooting procedure
Use the following information as a general procedure for diagnosing and troubleshooting problems you
experience with your server:
1. Verify that the power cords and the cables for all attached devices are connected correctly and securely.
2. Verify that the server and all attached devices that require ac power are connected to properly grounded,
functioning electrical outlets.
3. Verify that all installed hardware and attached devices are enabled in the BIOS settings of your server.
For more information about accessing and changing the BIOS settings, see “Using the Setup Utility
4. View the status and diagnostic LEDs to identify the system and device status and diagnose problems.
5. If the server is not working after you have added new software, installed a new optional device, or
replaced a piece of hardware, remove or reinstall the software, device, or hardware to see if the problem
could be solved.
7. Turn on the server and press Esc as soon as you see the logo screen to view any diagnostic messages.
8. Refer to “Basic troubleshooting tables” on page 154 and follow the instructions for the type of problem
you are experiencing. If the basic troubleshooting information does not help you resolve a problem,
continue with the next step.
9. Try using a previous server configuration to see if a recent change to hardware or software settings has
caused a problem. Before restoring your previous configuration, capture your current configuration in
case the older configuration settings do not solve the problem or have adverse effect.
10. Use an antivirus program to see if your server has been infected by a virus. If the program detects a
virus, remove the virus.
Viewing the status and diagnostic LEDs
Your server has status and diagnostic LEDs on the front panel, the rear panel, the panel of the diagnostic
module (varies by model), the system board, the hot-swap hard disk drives, and the optical drive (if
supported). The various LEDs help you easily identify the system and device status and diagnose problems.
Viewing the system event log
The system event log (SEL) contains information about all the POST and system management interrupt (SMI)
events. You can view the SEL to diagnose system problems.
© Copyright Lenovo 2012
153
Download from Www.Somanuals.com. All Manuals Search And Download.
The TMM implements the SEL as specified in the IPMI 2.0 specification. The SEL is accessible regardless of
the system power state through the TMM in-band and out-of-band interfaces.
For more information about viewing the SEL, refer to the ThinkServer Management Module User Guide,
Basic troubleshooting tables
Use the basic troubleshooting information to find solutions to problems that have definite symptoms.
ThinkServer EasyStartup program problems
Follow the suggested actions for the corresponding symptom in the order in which they are listed until the
problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 153
for the subsequent steps you should check after using the information in this topic. If the problem still cannot
be solved, seek technical assistance. See Chapter 8 “Getting information, help, and service” on page 159.
Note: If you are instructed to remove, install, or replace any CRUs, refer to the related procedure in Chapter
Action
Symptom
The ThinkServer EasyStartup DVD does not start.
1. Ensure that the server supports the ThinkServer
EasyStartup program and has a bootable DVD drive
installed or a bootable external DVD drive attached.
2. Ensure that you have set the optical drive with the
ThinkServer EasyStartup DVD installed as the first
startup device. See “Selecting a startup device” on
page 50.
3. Verify if the optical drive or the disc has problems.
The operating system installation program continuously
loops.
Make more space available on the hard disk drive.
1. Ensure that the operating system medium is
supported by the ThinkServer EasyStartup program
version your are using. For a list of the supported
operating systems, refer to the user guide and
compatibility notes for the ThinkServer EasyStartup
program through the program main interface. See
page 54.
The ThinkServer EasyStartup program cannot start the
operating system medium.
2. Verify if the optical drive or the disc has problems.
Optical drive problems
Follow the suggested actions for the corresponding symptom in the order in which they are listed until the
problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 153
for the subsequent steps you should check after using the information in this topic. If the problem still cannot
be solved, seek technical assistance. See Chapter 8 “Getting information, help, and service” on page 159.
Notes:
• If you are instructed to remove, install, or replace any CRUs, refer to the related procedure in Chapter 6
154 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
• If an action step is preceded by “(Trained service technician only),” this action step is reserved for a trained
service technician and must be performed only by a trained service technician.
Action
Symptom
The optical drive is not recognized.
1. Ensure that:
• The related cables and connectors are not
damaged and the connector pins are not bent.
• The optical drive is securely connected to the
correct SATA connector on the system board and
the SATA connector is enabled in the Setup Utility
program. See “Using the Setup Utility program”
on page 45.
• All cables and jumpers (if any) are installed
correctly.
• The correct device driver is installed for the optical
drive.
2. Run any optical drive diagnostic programs if you
have.
3. Reinstall the optical drive and reconnect cables.
4. Replace the signal cable for the optical drive.
5. Replace the power cable for the optical drive.
6. Replace the power cable for the backplane.
7. Replace the optical drive.
8. Replace the backplane.
9. (Trained service technician only) Replace the system
board.
A disc is not working correctly.
1. Ensure that the disc is in the optical drive with the
shiny side facing down.
2. Ensure that the disc surface is clean and not
scratched.
3. Check the disc or package for regional coding. You
might need to purchase a disc with coding for the
region where you are using the product.
4. Restart the disc player program.
5. Restart the server.
6. Run any optical drive diagnostic programs if you
have.
7. Reinstall the optical drive and reconnect cables.
8. Replace the signal cable for the optical drive.
9. Replace the optical drive.
Hard disk drive problems
Follow the suggested actions for the corresponding symptom in the order in which they are listed until the
problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 153
for the subsequent steps you should check after using the information in this topic. If the problem still cannot
be solved, seek technical assistance. See Chapter 8 “Getting information, help, and service” on page 159.
Notes:
Chapter 7. Troubleshooting and diagnostics 155
Download from Www.Somanuals.com. All Manuals Search And Download.
• If you are instructed to remove, install, or replace any CRUs, refer to the related procedure in Chapter 6
• The status LEDs on each hot-swap hard disk drive help you easily identify a problem. See “Hot-swap
Action
Symptom
A newly installed hot-swap hard disk drive is not
recognized.
1. Ensure that the drive is installed into the correct drive
bay.
2. Restart the server.
3. Remove the drive from the bay, wait 45 seconds,
and reinsert the drive into the bay, making sure that
the drive connects to the hot-swap hard disk drive
backplane.
4. Run any diagnostic programs to test the hard disk
drive if you have.
5. Ensure that the hot-swap hard disk drive backplane
is correctly seated. When it is correctly seated,
the drive assemblies correctly connect to the
backplane without bowing or causing movement of
the backplane.
6. Ensure that the cable connection is correct. See
“Mini-SAS to mini-SAS signal cable connections” on
page 29.
7. Reconnect the backplane power cable and repeat
step 1 through step 4.
8. Reconnect the backplane signal cable and repeat
step 1 through step 4.
9. If you suspect a problem with the backplane signal
cable or the backplane:
a. Replace the affected backplane signal cable.
b. Replace the affected backplane.
Multiple hard disk drives fail.
1. Ensure that the cable connection is correct. See
“Mini-SAS to mini-SAS signal cable connections” on
page 29.
2. Reconnect the power cable(s).
3. Reconnect the signal cable(s).
4. Replace the affected signal cable(s).
5. If you suspect a problem with the backplane, replace
the affected backplane.
Memory module problems
Follow the suggested actions for the corresponding symptom in the order in which they are listed until the
problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 153
for the subsequent steps you should check after using the information in this topic. If the problem still cannot
be solved, seek technical assistance. See Chapter 8 “Getting information, help, and service” on page 159.
Notes:
• If you are instructed to remove, install, or replace any CRUs, refer to the related procedure in Chapter 6
156 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
• If an action step is preceded by “(Trained service technician only),” this action step is reserved for a trained
service technician and must be performed only by a trained service technician.
Action
Symptom
The amount of system memory that is displayed is less
than the total capacity of the installed physical memory
modules and you suspect a memory module problem.
1. Ensure that:
• All memory modules are the correct type
• You followed the memory module installation
rules. See “Memory module installation rules” on
page 75.
• All memory modules are seated correctly and
securely.
• The system firmware is up-to-date.
2. Reinstall the memory modules.
3. Replace the suspect memory modules.
4. (Trained service technician only) Replace the system
board.
Keyboard, mouse, and USB device problems
Follow the suggested actions for the corresponding symptom in the order in which they are listed until the
problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 153
for the subsequent steps you should check after using the information in this topic.
Action
Symptom
All or some keys on the keyboard do not work.
1. Ensure that:
• The USB keyboard cable is securely connected
to a USB connector on the server. If the USB
keyboard is connected to a USB hub, disconnect
the keyboard from the hub and connect it directly
to the server.
• No keys are stuck.
• The USB controller is enabled in the Setup Utility
program. See “Using the Setup Utility program”
on page 45.
2. Restart the server.
3. Replace the keyboard.
1. Ensure that:
The mouse or pointing device does not work.
• The mouse or pointing device cable is securely
connected to the server. If the USB mouse or
pointing device is connected to a USB hub,
disconnect the mouse or pointing device from the
hub and connect it directly to the server.
• The mouse or pointing device is clean and no dust
accumulates.
• The device drivers are installed correctly.
• The USB controller is enabled in the Setup Utility
program. See “Using the Setup Utility program”
on page 45.
2. Restart the server.
Chapter 7. Troubleshooting and diagnostics 157
Download from Www.Somanuals.com. All Manuals Search And Download.
Action
Symptom
3. Replace the mouse or pointing device.
1. Ensure that:
A USB device does not work.
• The USB cable is securely connected to the server.
If the USB device is connected to a USB hub,
disconnect the device from the hub and connect
it directly to the server.
• The device drivers are installed correctly.
• The USB controller is enabled in the Setup Utility
program. See “Using the Setup Utility program”
on page 45.
2. Restart the server.
3. Replace the USB device.
158 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Getting information, help, and service
This chapter contains information about help, service, and technical assistance for products manufactured
by Lenovo and where to go for additional information about Lenovo and Lenovo products.
Information resources
You can use the information in this topic to access useful resources relating to your needs when using
the product.
Using the documentation
Information about your Lenovo system and installed software, if any, or optional devices is available in the
documentation that comes with the product. The documentation can include printed documents, online
documents, readme files, and help files. Most of the documentation for your server is on the documentation
DVD provided with your server. Refer to the troubleshooting information in your server User Guide
for instructions on how to diagnose problems and do basic troubleshooting. The troubleshooting and
diagnostics information might tell you that you need additional or updated device drivers or other software.
Lenovo maintains pages on the World Wide Web where you can get the latest technical information and
download documentation or device drivers and updates. To access the Lenovo Support Web site, go to:
If you suspect a software problem, refer to the documentation, including readme files and online help, that
comes with the operating system or software program.
ThinkServer Web site
The ThinkServer Web site provides up-to-date information and services to help you buy, use, upgrade, and
maintain your server. You also can do the following by visiting the ThinkServer Web site at:
• Shop for servers as well as upgrades and accessories for your server.
• Purchase additional services and software.
• Purchase upgrades and extended hardware repair services.
• Access the Lenovo Limited Warranty (LLW).
• Access the online manuals for your products.
• Access troubleshooting and support information for your server model and other supported products.
• Download the latest device drivers and software updates for your server model.
• Find the service and support phone numbers for your country or region.
• Find a Service Provider located near you.
Lenovo Support Web site
Technical support information is available on the Lenovo Support Web site at:
This Web site is updated with the latest support information such as the following:
• Drivers and software
© Copyright Lenovo 2012
159
Download from Www.Somanuals.com. All Manuals Search And Download.
• Diagnostic solutions
• Product and service warranty
• Product and parts details
• User guides and manuals
• Knowledge base and frequently asked questions
Help and service
This topic contains information about obtaining help and service.
Before you call
Before you call, do the following to try to solve the problem by yourself:
• Check all cables to ensure that they are connected.
• Check the power switches to ensure that the system and optional devices are turned on.
• Use the troubleshooting information in your system documentation on the documentation DVD that
comes with your product.
• Check for the updated information, new device drivers, and hints and tips on the Lenovo Support Web
site at:
If possible, be at your product when you call. Have the following information available:
• Machine type and model
• Serial numbers of your Lenovo hardware products
• Description of the problem
• Exact wording of any error messages
• Hardware and software configuration information
Calling for service
During the warranty period, you can get help and information by telephone through the Customer Support
Center.
The following services are available during the warranty period:
• Problem determination - Trained service personnel are available to assist you with determining a
hardware problem and deciding what action is necessary to fix the problem.
• Hardware repair - If the problem is caused by hardware under warranty, trained service personnel are
available to provide the applicable level of service.
• Engineering Change management - There might be changes that are required after a product has
been sold. Lenovo or your reseller will make selected Engineering Changes (ECs) that apply to your
hardware available.
The warranty does not cover the following:
• Replacement or use of parts not manufactured for or by Lenovo or non-warranted Lenovo parts
• Identification of software problem sources
• Configuration of the Unified Extensible Firmware Interface (UEFI) BIOS as part of an installation or upgrade
• Changes, modifications, or upgrades to device drivers
• Installation and maintenance of network operating systems (NOS)
• Installation and maintenance of application programs
160 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
For the warranty type and duration for your product, refer to the Warranty and Support Information on
the documentation DVD that comes with you server. You must retain your proof of purchase to obtain
warranty service.
For warranty service, consult the worldwide Lenovo Support telephone list. Telephone numbers are subject
to change without notice. The most up-to-date telephone list for Lenovo Support is always available on the
Web site at http://www.lenovo.com/support/phone. If the telephone number for your country or region is not
listed, contact your Lenovo reseller or Lenovo marketing representative.
Using other services
If you travel with a Lenovo notebook computer or relocate your computer to a country where your desktop,
notebook, or server machine type is sold, your computer might be eligible for International Warranty Service,
which automatically entitles you to obtain warranty service throughout the warranty period. Service will be
performed by service providers authorized to perform warranty service.
Service methods and procedures vary by country, and some services might not be available in all countries.
International Warranty Service is delivered through the method of service (such as depot, carry-in, or
on-site service) that is provided in the servicing country. Service centers in certain countries might not be
able to service all models of a particular machine type. In some countries, fees and restrictions might
apply at the time of service.
To determine whether your computer is eligible for International Warranty Service and to view a list of the
countries where service is available, go to http://www.lenovo.com/support, click Warranty, and follow
the instructions on the screen.
For technical assistance with the installation of or questions related to Service Packs for
your installed Windows product, refer to the Microsoft Product Support Services Web site at
http://support.microsoft.com/directory or you can contact the Customer Support Center. Some fees might
apply.
Purchasing additional services
During and after the warranty period, you can purchase additional services, such as support for hardware,
operating systems, and application programs; network setup and configuration services; upgraded or
extended hardware repair services; and custom installation services. Service availability and service names
might vary by country or region. For more information about these services, go to the Lenovo Web site at:
Chapter 8. Getting information, help, and service 161
Download from Www.Somanuals.com. All Manuals Search And Download.
162 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's
responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply
to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo
or third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of
the materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been
made on development-level systems and there is no guarantee that these measurements will be the same
on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.
© Copyright Lenovo 2012
163
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
Lenovo, the Lenovo logo, and ThinkServer are trademarks of Lenovo in the United States, other countries, or
both.
Intel and Intel Xeon are trademarks of Intel Corporation in the United States, other countries, or both.
Internet Explorer, Microsoft, Windows, and Windows Server are trademarks of the Microsoft group of
companies.
Linux is a registered trademark of Linus Torvalds.
Other company, product, or service names may be trademarks or service marks of others.
Important notes
Processor speed indicates the internal clock speed of the microprocessor; other factors also affect
application performance.
CD or DVD drive speed is the variable read rate. Actual speeds vary and are often less than the possible
maximum.
When referring to processor storage, real and virtual storage, or channel volume, KB stands for 1 024 bytes,
MB stands for 1 048 576 bytes, and GB stands for 1 073 741 824 bytes.
When referring to hard disk drive capacity or communications volume, MB stands for 1 000 000 bytes,
and GB stands for 1 000 000 000 bytes. Total user-accessible capacity can vary depending on operating
environments.
Maximum internal hard disk drive capacities assume the replacement of any standard hard disk drives
and population of all hard disk drive bays with the largest currently supported drives that are available
from Lenovo.
Maximum memory might require replacement of the standard memory with an optional memory module.
Lenovo makes no representations or warranties with respect to non-Lenovo products. Support (if any) for
the non-Lenovo products is provided by the third party, not Lenovo.
Some software might differ from its retail version (if available) and might not include user manuals or all
program functionality.
Polyvinyl Chloride (PVC) cable and cord notice
WARNING: Handling the cord on this product or cords associated with accessories sold with this product
will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
Recycling information
Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment
when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in
recycling their IT products. For information on recycling Lenovo products, go to:
164 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery return program
This product may contain a lithium or lithium ion battery. Consult your user manual or service manual for
specific battery information. The battery must be recycled or disposed of properly. Recycling facilities may
not be available in your area. For information on disposal or batteries outside the United States, go to
Battery recycling information for the United States and Canada
Battery recycling information for the European Union
Notice: This mark applies only to countries within the European Union (EU).
Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC
concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the
framework for the return and recycling of used batteries and accumulators as applicable throughout the
European Union. This label is applied to various batteries to indicate that the battery is not to be thrown
away, but rather reclaimed upon end of life per this Directive.
In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to indicate
that they are to be collected separately and recycled at end of life. The label on the battery may also
include a chemical symbol for the metal concerned in the battery (Pb for lead, Hg for mercury, and Cd for
cadmium). Users of batteries and accumulators must not dispose of batteries and accumulators as unsorted
municipal waste, but use the collection framework available to customers for the return, recycling, and
treatment of batteries and accumulators. Customer participation is important to minimize any potential
effects of batteries and accumulators on the environment and human health due to the potential presence of
hazardous substances. For proper collection and treatment, go to:
Requirement for batteries containing perchlorate
The following statement applies to users in the state of California, U.S.A.
California Perchlorate Information:
Products containing CR (manganese dioxide) lithium coin cell batteries may contain perchlorate.
Perchlorate Material - special handling may apply, See
Appendix A. Notices 165
Download from Www.Somanuals.com. All Manuals Search And Download.
Particulate contamination
Attention: Airborne particulates (including metal flakes or particles) and reactive gases acting alone or in
combination with other environmental factors such as humidity or temperature might pose a risk to the
server that is described in this document. Risks that are posed by the presence of excessive particulate
levels or concentrations of harmful gases include damage that might cause the server to malfunction or
cease functioning altogether. This specification sets forth limits for particulates and gases that are intended
to avoid such damage. The limits must not be viewed or used as definitive limits, because numerous
other factors, such as temperature or moisture content of the air, can influence the impact of particulates
or environmental corrosives and gaseous contaminant transfer. In the absence of specific limits that are
set forth in this document, you must implement practices that maintain particulate and gas levels that are
consistent with the protection of human health and safety. If Lenovo determines that the levels of particulates
or gases in your environment have caused damage to the server, Lenovo may condition provision of repair
or replacement of servers or parts on implementation of appropriate remedial measures to mitigate such
environmental contamination. Implementation of such remedial measures is a customer responsibility.
Table 6. Limits for particulates and gases
Contaminant
Limits
Particulate
• The room air must be continuously filtered with 40% atmospheric dust spot efficiency
(MERV 9) according to ASHRAE Standard 52.21.
• Air that enters a data center must be filtered to 99.97% efficiency or greater, using
high-efficiency particulate air (HEPA) filters that meet MIL-STD-282.
• The deliquescent relative humidity of the particulate contamination must be more than 60%2.
• The room must be free of conductive contamination such as zinc whiskers.
Gaseous
• Copper: Class G1 as per ANSI/ISA 71.04-19853
• Silver: Corrosion rate of less than 300 Å in 30 days
1 ASHRAE 52.2-2008 - Method of Testing General Ventilation Air-Cleaning Devices for Removal Efficiency by Particle
Size. Atlanta: American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.
2 The deliquescent relative humidity of particulate contamination is the relative humidity at which the dust absorbs
enough water to become wet and promote ionic conduction.
3
ANSI/ISA-71.04-1985. Environmental conditions for process measurement and control systems: Airborne
contaminants. Instrument Society of America, Research Triangle Park, North Carolina, U.S.A.
Important information for the European Directive 2002/96/EC
The Waste Electrical and Electronic Equipment (WEEE) mark applies only to countries within the European
Union (EU) and Norway. Appliances are labeled in accordance with European Directive 2002/96/EC
concerning waste electrical and electronic equipment (WEEE). The Directive determines the framework for
the return and recycling of used appliances as applicable throughout the European Union. This label is
applied to various products to indicate that the product is not to be thrown away, but rather reclaimed upon
end of life per this Directive. Users of electrical and electronic equipment (EEE) with the WEEE marking per
166 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Annex IV of the WEEE Directive must not dispose of end of life EEE as unsorted municipal waste, but use the
collection framework available to them for the return, recycle, recovery of WEEE and minimize any potential
effects of EEE on the environment and human health due to the presence of hazardous substances. For
additional WEEE information go to:
Le marquage des déchets d'équipements électriques et électroniques (DEEE) s'applique uniquement aux
pays de l'Union européenne (EU) et à la Norvège. Les appareils sont marqués conformément à la Directive
2002/96/CE du Conseil Européen relative aux déchets d'équipements électriques et électroniques (DEEE).
Cette directive, applicable à l'ensemble des pays de l'Union européenne, concerne la collecte et le recyclage
des appareils usagés. Ce marquage est apposé sur différents produits pour indiquer que ces derniers
ne doivent pas être jetés, mais récupérés en fin de vie, conformément à cette directive. Les utilisateurs
d'équipements électriques et électroniques portant le marquage DEEE, conformément à l'Annexe IV de la
Directive DEEE, ne doivent pas mettre au rebut ces équipements comme des déchets municipaux non triés,
mais ils doivent utiliser la structure de collecte mise à disposition des clients pour le retour, le recyclage et la
récupération des déchets d'équipements électriques et électroniques, afin de réduire tout effet potentiel
des équipements électriques et électroniques sur l'environnement et la santé en raison de la présence
possible de substances dangereuses dans ces équipements. Pour plus d'informations sur les équipements
Die WEEE-Kennzeichnung gilt nur in Ländern der Europäischen Union und in Norwegen. Geräte werden
gemäß der Richtlinie 2002/96/EC der Europäischen Union über Elektro- und Elektronikaltgeräte (WEEE)
gekennzeichnet. Die Richtlinie regelt die Rückgabe und Wiederverwertung von Altgeräten innerhalb der
Europäischen Union. Mit dieser Kennzeichnung versehene Altgeräte dürfen gemäß dieser Richtlinie
nicht weggeworfen werden, sondern müssen zurückgegeben werden. Anwender von Elektro- und
Elektronikgeräten mit der WEEE-Kennzeichnung dürfen diese gemäß Annex IV der WEEE-Richtlinie nach
ihrem Gebrauch nicht als allgemeinen Hausmüll entsorgen. Stattdessen müssen diese Geräte im verfügbaren
Sammelsystem zurückgegeben werden und damit einem Recycling- oder Wiederherstellungsprozess
zugeführt werden, bei dem mögliche Auswirkungen der Geräte auf die Umwelt und den menschlichen
Organismus aufgrund gefährlicher Substanzen minimiert werden. Weitere Informationen zur Entsorgung von
La marca de Residuos de equipos eléctricos y electrónicos (WEEE) se aplica sólo a los países pertenecientes
a la Unión Europea (UE) y a Noruega. Los aparatos se etiquetan conforme a la Directiva Europea 2002/96/EC
relativa a los residuos de equipos eléctricos y electrónicos (WEEE). La directiva determina el marco para
devolver y reciclar los aparatos usados según sea aplicable en toda la Unión Europea. Esta etiqueta se
aplica a varios productos para indicar que el producto no se va a desechar, sino que va ser reclamado por
esta Directiva, una vez termine su ciclo de vida. Los usuarios de los equipos eléctricos y electrónicos (EEE)
con la marca WEEE por el Anexo IV de la Directiva WEEE no deben tratar los EEE como desperdicios
municipales no clasificados, una vez terminado su ciclo de vida, sino que deben utilizar el marco de recogida
disponible para devolver, reciclar y recuperar los WEEE y minimizar los posibles efectos de los EEE en el
medio ambiente y en la salud debidos a la presencia de substancias peligrosas. Para obtener información
Il marchio WEEE (Waste Electrical and Electronic Equipment) viene applicato soltanto ai paesi all'interno
dell'unione europea (EU) e norvegia. Le apparecchiature vengono etichettate in accordo con la direttiva
europea 2002/96/EC riguardande lo smaltimento di apparecchiatura elettrica ed alettronica (WEEE). Le
direttive determinano la procedura di restituzione e di riciclaggio delle apparecchiature usate in conformità
con le normative dell'unione europea. Questa classificazione viene applicata a vari prodotti per indicare che
il prodotto stesso non deve essere gettato ma riscattato al termine dell'utilizzo per quasta direttiva. Gli utenti
di apparecchiature elettriche o elettroniche (EEE) marchiate WEEE secondo Annex IV della direttiva WEEE
non devono disporre di fine utilizzo EEE come rifiuto, municipale non classificato, ma deve essere utilizzata
la procedura di classificazione disponibile per il riscatto, riciclo, recupero del WEEE e minimizzare qualsiasi
potenziale effetto della EEE sull'ambiente e sulla salute umana dovuto alla presenza di sostanze pericolose.
Appendix A. Notices 167
Download from Www.Somanuals.com. All Manuals Search And Download.
A marca REEE (Resíduos de Equipamentos Eléctricos e Electrónicos) aplica-se apenas aos Estados
Membros da União Europeia e à Noruega. Os aparelhos eléctricos deverão ser identificados em
conformidade com a Directiva Europeia 2002/96/CE relativa a REEE (Resíduos de Equipamentos Eléctricos
e Electrónicos). A Directiva determina o enquadramento normativo relativamente à devolução e reciclagem
de aparelhos eléctricos utilizados, conforme aplicável no espaço da União Europeia. Esta etiqueta
deverá ser aposta em diversos produtos para indicar que os mesmos não poderão ser deitados fora,
mas sim recuperados no final da respectiva vida útil, de acordo com a referida Directiva. Os utilizadores
de equipamentos eléctricos e electrónicos (EEE) com a marca REEE em conformidade com o Anexo IV da
Directiva REEE não poderão deitar fora os EEE no final da respectiva vida útil como lixo municipal não
separado, devendo sim utilizar a estrutura de recolha que lhes tenha sido disponibilizada para efeitos de
devolução, reciclagem e recuperação de REEE, por forma a minimizar potenciais efeitos dos EEE sobre
o ambiente e saúde pública resultantes da presença de substâncias perigosas. Para obter informações
Het WEEE-merkteken (Waste Electrical and Electronic Equipment) geldt alleen voor landen binnen de
Europese Unie (EU) en Noorwegen. Apparaten worden van een merkteken voorzien overeenkomstig
Europese Richtlijn 2002/96/EC inzake afgedankte elektrische en elektronische apparatuur (waste electrical
and electronic equipment, WEEE). Deze richtlijn bepaalt het raamwerk voor het retourneren en recyclen van
gebruikte apparatuur, zoals van toepassing binnen de Europese Unie. Dit merkteken wordt aangebracht op
diverse producten om aan te geven dat het product in kwestie niet dient te worden weggegooid, maar dat
het aan het eind van de levenscyclus krachtens deze Richtlijn dient te worden geretourneerd. Gebruikers van
elektrische en elektronische apparaten (EEE) welke zijn voorzien van het WEEE-merkteken zijn gehouden
aan Annex IV van de WEEE Richtlijn en mogen gebruikte EEE niet weggooien als ongesorteerd afval, maar
dienen gebruik te maken van het inzamelproces voor het teruggeven, recyclen en terugwinnen van WEEE
dat voor hen beschikbaar is, en dienen de mogelijke effecten die EEE ten gevolge van de aanwezigheid van
schadelijke stoffen kunnen hebben op het milieu en de volksgezondheid, tot een minimum te beperken. Voor
WEEE-mærkningen (Waste Electrical and Electronic Equipment) gælder kun for lande i EU samt Norge.
Udstyr mærkes i henhold til EU's direktiv 2002/96/EF om affald af elektrisk og elektronisk udstyr (WEEE).
Direktivet fastlægger de rammer, der gælder for returnering og genbrug af brugt udstyr i EU. Mærkaten
påsættes forskellige produkter for at angive, at produktet ikke må smides væk, når det er udtjent, men skal
genvindes i henhold til dette direktiv. Brugere af elektrisk og elektronisk udstyr (EEE), der er mærket med
WEEE-mærket som angivet i Bilag IV til WEEE-direktivet, må ikke bortskaffe brugt EEE som usorteret
husholdningsaffald, men skal bruge den indsamlingsordning, der er etableret, så WEEE kan returneres,
genbruges eller genvindes. Formålet er at minimere den eventuelle påvirkning af miljøet og menneskers
sundhed som følge af tilstedeværelsen af skadelige stoffer. Der er flere oplysninger om affald af elektrisk
Sähkö- ja elektroniikkalaiteromu (Waste electrical and electronic equipment, WEEE) -merkintä koskee vain
Euroopan unionin (EU) jäsenmaita ja Norjaa. Sähkö- ja elektroniikkalaitteet merkitään Euroopan parlamentin
ja neuvoston direktiivin 2002/96/EY mukaisesti. Kyseinen direktiivi määrittää Euroopan Unionin alueella
käytössä olevat palautus- ja kierrätyskäytännöt. WEEE-merkintä laitteessa osoittaa, että direktiivin ohjeiden
mukaan tuotetta ei tulisi hävittää sen elinkaaren päässä, vaan se tulee toimittaa uusiokäyttöön. Käyttäjien,
joiden sähkö- ja elektroniikkalaitteissa on tämä sähkö- ja elektroniikkalaiteromun direktiivin liitteen IV
mukainen merkintä, tulee kierrättää kyseiset laitteet käytettävissä olevien resurssien mukaan ja varmistaa,
että niistä tai niissä käytetyistä materiaaleista ei aiheudu haittaa ympäristölle tai ihmisten terveydelle. Sähkö-
ja elektroniikkalaitteita ei saa hävittää sekajätteen mukana. Lisätietoja sähkö- ja elektroniikkalaiteromun
WEEE-merket (Waste Electrical and Electronic Equipment) gjelder bare for land i Den europeiske union
(EU) og Norge. Utstyr merkes i henhold til EU-direktiv 2002/96/EF om avfall fra elektrisk og elektronisk
utstyr (WEEE). Direktivet fastsetter rammene for retur og resirkulering av brukt utstyr innenfor EU. Dette
merket benyttes på forskjellige produkter for å angi at produktet ikke må kastes, men må behandles i
henhold til dette direktivet ved slutten av produktets levetid. Brukere av elektrisk og elektronisk utstyr
168 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
(EEE) som er merket med WEEE-merket ifølge vedlegg IV i WEEE-direktivet, må ikke kaste utstyret som
usortert husholdningsavfall, men må bruke de tilgjengelige innsamlingssystemene for retur, resirkulering og
gjenvinning av kassert elektrisk og elektronisk utstyr for å redusere en eventuell skadelig virkning av elektrisk
og elektronisk utstyr på miljø og helse, som skyldes skadelige stoffer. Du finner mer informasjon om WEEE
Appendix A. Notices 169
Download from Www.Somanuals.com. All Manuals Search And Download.
German Ordinance for Work gloss statement
The product is not suitable for use with visual display work place devices according to clause 2 of the
German Ordinance for Work with Visual Display Units.
Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der
Bildschirmarbeitsverordnung geeignet.
Export classification notice
This product is subject to the United States Export Administration Regulations (EAR) and has an Export
Classification Control Number (ECCN) of 4A994.b. It can be re-exported except to any of the embargoed
countries in the EAR E1 country list.
Electronic emission notices
The following information refers to the Lenovo ThinkServer machine types 3072, 3073, 3074, 4302, 4304,
and 4305.
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits.
Lenovo is not responsible for any radio or television interference caused by using other than specified or
recommended cables and connectors or by unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Industry Canada Class A emission compliance statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
United Kingdom telecommunications safety requirement
Notice to Customers
This apparatus is approved under approval number NS/G/1234/J/100003 for indirect connection to public
telecommunication systems in the United Kingdom.
170 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
European Union - Compliance to the Electromagnetic Compatibility Directive
This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the
approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot
accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended
modification of the product, including the installation of option cards from other manufacturers.
This product has been tested and found to comply with the limits for Class A Information Technology
Equipment according to European Standard EN 55022. The limits for Class A equipment were derived for
commercial and industrial environments to provide reasonable protection against interference with licensed
communication equipment.
Warning: This is a Class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
German Class A compliance statement
Deutschsprachiger EU Hinweis:
Hinweis für Geräte der Klasse A EU-Richtlinie zur Elektromagnetischen Verträglichkeit
Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG (früher 89/336/EWG) zur
Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten
und hält die Grenzwerte der EN 55022 Klasse A ein.
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu
betreiben. Des Weiteren dürfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden.
Lenovo übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt
ohne Zustimmung der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne
Empfehlung der Lenovo gesteckt/eingebaut werden.
Deutschland:
Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Betriebsmittein
Dieses Produkt entspricht dem „Gesetz über die elektromagnetische Verträglichkeit von Betriebsmitteln“
EMVG (früher „Gesetz über die elektromagnetische Verträglichkeit von Geräten“). Dies ist die Umsetzung der
EU-Richtlinie 2004/108/EG (früher 89/336/EWG) in der Bundesrepublik Deutschland.
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit
von Betriebsmitteln, EMVG vom 20. Juli 2007 (früher Gesetz über die elektromagnetische
Verträglichkeit von Geräten), bzw. der EMV EG Richtlinie 2004/108/EC (früher 89/336/EWG), für
Geräte der Klasse A.
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen
- CE - zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo
(Deutschland) GmbH, Gropiusplatz 10, D-70563 Stuttgart.
Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4:
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A.
Nach der EN 55022: „Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich
Funkstörungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Maßnahmen
durchzuführen und dafür aufzukommen.“
Appendix A. Notices 171
Download from Www.Somanuals.com. All Manuals Search And Download.
Nach dem EMVG: „Geräte dürfen an Orten, für die sie nicht ausreichend entstört sind, nur mit besonderer
Genehmigung des Bundesministers für Post und Telekommunikation oder des Bundesamtes für Post und
Telekommunikation betrieben werden. Die Genehmigung wird erteilt, wenn keine elektromagnetischen
Störungen zu erwarten sind.“ (Auszug aus dem EMVG, Paragraph 3, Abs. 4). Dieses Genehmigungsverfahren
ist nach Paragraph 9 EMVG in Verbindung mit der entsprechenden Kostenverordnung (Amtsblatt 14/93)
kostenpflichtig.
Anmerkung: Um die Einhaltung des EMVG sicherzustellen sind die Geräte, wie in den Handbüchern
angegeben, zu installieren und zu betreiben.
ENERGY STAR model information
ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency and the U.S. Department
of Energy aimed at saving money and protecting the environment through energy efficient products and
practices.
Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation. Some
models of the following machine types have been designed and tested to conform to the ENERGY STAR
program requirement for computer servers at the time of manufacture: 3072, 3073, 3074, 4302, 4304,
and 4305.
By using ENERGY STAR compliant products and taking advantage of the power-management features of
your server, you reduce the consumption of electricity. Reduced electrical consumption contributes to
potential financial savings, a cleaner environment, and the reduction of greenhouse gas emissions.
For more information about ENERGY STAR, go to:
http://www.energystar.gov
Lenovo encourages you to make efficient use of energy an integral part of your day-to-day operations. To
help in this endeavor, set the following power-management features to take effect when your servers
have been used:
• Processor- or core-reduced power states
• Variable speed fan control based on power or thermal readings
• Low power memory states
• Liquid cooling capability
172 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
2.5-inch hard disk drive backplane
locations 28
using 159
3.5-inch hard disk drive backplane
locations 27
E
EasyUpdate Firmware Updater program
using 64
error
A
LED 19
Advanced menu
advanced SATA/SAS hardware RAID
configuring 63
Ethernet card
installing 81
ambient temperature limit LED
LED 20
removing 83
Ethernet connectivity
features
9
Ethernet connector 0
Ethernet controllers
configuring 64
Ethernet status
B
Boot Manager menu
Boot Options menu
LED 21
exiting
expansion slots
features
8
C
cable connection 29
configuring
F
server 45
features
7
firmware
updating 64
flashing
the BIOS 52
front panel
configuring RAID
consistency check
LED 17
locations 17
running 62
front panel board
replacing 141
front view of the server
locations 14
cooling shroud
reinstalling 74
removing 73
creating, adding, or deleting
CRU
G
gaseous contamination 166
getting information 159
D
DIMM
guidelines 67
installing 78
removing 80
H
hardware
documentation
© Copyright Lenovo 2012
173
Download from Www.Somanuals.com. All Manuals Search And Download.
installing 67
removing 67
replacing 67
Intelligent Diagnostics Module
locations 19
heat sink
help, getting 159
hot-spare drive
internal drives
setting 61
features
8
hot-swap hard disk drive
installing
122
replacing 122
hot-swap hard disk drive backplane
locations 27
L
LED
replacing 132
hot-swap hard disk drive status
LED 25
hot-swap hard disk drive status LEDs
locations 25
hot-swap redundant power supply
installing 107
replacing 109
hot-swap redundant power supply status
LED 21
front panel 17
IDM 19
NIC status 18
Lenovo Rack Planner
Lenovo ThinkServer EasyManage
I
ID button
LED 18
IDM
replace 137
IDM panel
Lenovo ThinkServer EasyManage program
using 65
LED 19
locations 13
locations 19
initializing
Input/Output (I/O)
low-profile
LSI Software RAID Configuration Utility program
starting 59
features
8
installation rules
DIMM 75
installing
DIMM 78
M
machine type and model label
locations 13
Main menu
MegaRAID Storage Manager program
memory
features
8
memory module
installing 78
removing 80
guidelines 75
installing and using
installing or replacing
features
8
installing 113
replacing 118
174 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
N
NIC status
LED 18
O
optical drive
TR 500 Key
replace
IDM 137
replacing
91
option
front panel board
141
P
password
PCI Express card slot
riser card assembly 1
replacing 143
road map
physical drive
rebuilding 62
power status
server setup
running
5
LED 18
power supply
features
8
precautions
guidelines 67
S
Save & Exit menu
Security menu
serial number label
locations 13
R
RAID
configuring 56
introduction 56
RAID array
RAID card
server components
locations 22
server configuration
updating 151
installing 85
locations 25
server cover
removing 88
installing 147
RAID configuration utilities
removing 69
server documentation
2
rear view of the server
locations 20
rebuilding
recovering
server package
server setup
7
road map
5
the BIOS 52
reinstalling
setting
reliability, availability, and serviceability
setting, changing, deleting
features
9
removing
Setup Utility program
exiting 51
DIMM 80
starting 45
© Copyright Lenovo 2012
175
Download from Www.Somanuals.com. All Manuals Search And Download.
TPM 50
LED 40
using 45
slim optical drive
ThinkServer RAID 300
configuring 58
locations 15, 17
specifications 11
starting
installing 103
startup device
removing 104
ThinkServer Web address
TMM Premium
installing 100
removing 101
TPM
1
selecting 50
static-sensitive devices
guidelines 68
TR 300 Key
LED 39
installing 96
removing 97
TR 500 Key
system board battery
replacing 145
installing 89
removing 91
locations 31
TR 700 Battery
installing 93
locations 34
system board LEDs
locations 39
system date
setting 48
system event log
system fan
replacing 139
LED 41
removing 94
troubleshooting and diagnostics
system fans
features
8
system reliability
guidelines 69
system status
LED 18
system time
setting 48
U
updating
the BIOS 52
updating or recovering
the BIOS 51
using
documentation 159
T
the BIOS
flashing 52
recovering 52
updating 52
ThinkServer EasyStartup
ThinkServer EasyStartup program
starting 54
V
video subsystem
using 53
features
9
ThinkServer EasyUpdate Firmware Updater
viewing information
virtual drive
176 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
initializing 61
W
Web site
compatible options 75–76
guidelines 69
© Copyright Lenovo 2012
177
Download from Www.Somanuals.com. All Manuals Search And Download.
178 ThinkServer RD330 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Kunz Lawn Mower MR55B User Manual
Land Pride Lawn Mower 701 069A User Manual
Lasko Ventilation Hood 4907ES User Manual
Lincoln Electric Welding System K386 User Manual
Logitech Radio 930 000101 User Manual
Makita Drill DA3010 User Manual
Makita Power Screwdriver 6823N 6824N User Manual
Maytag Washer MAT14CS User Manual
Mazda Bluetooth Headset HTS3367 User Manual
Melissa Styling Iron 635 069 User Manual